Search Results

Search found 1541 results on 62 pages for 'ivy bridge'.

Page 17/62 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• VMWare Player guest does not re-aquire IP on bridged interface after host loses and re-acquires network connectivity

  - by Vineet

  I am running a Ubuntu Linux image in VMWare Player on my laptop. The host is Windows XP. There are two network adapters configured in VMWare Player - one is host-only and the other is bridged. Everything works fine as long as the host does not lose network connectivity. If the host loses connectivity (even briefly) and then re-acquires it, my bridged adapter in VMWare Player is still unable to get an IP address. The host-only adapter remains unaffected. Disconnecting/Reconnecting the bridged adapter does not help. Simply restarting the guest OS does not help. Restarting VMWare Player does not help. The only remedy is to reboot the host and then bring up VMWare Player all over again. Is there something I can try to avoid this reboot? I searched the existing questions but they seemed to talk about adapters in NAT mode, whereas I am interested in retaining Bridged mode.

  Read the article

• Adding a Second Wireless Router to an Existing Wired Network

  - by KVCrawford

  I apologize ahead of time, I know this has been asked before, but I'm still having problems...maybe you guys can help. I started out with the basic instructions from the highest-voted answer at http://serverfault.com/questions/41572/adding-a-second-wireless-router-to-my-network The new Wireless router in question is a Linksys Wireless-N Gigabit Router, Model # WRT310N Here are the steps I've taken in setting it up: Plug my laptop into LAN port #2 in the new router. Nothing else is connected at this point Configure the new router to be 192.168.1.200 (the original router is 192.168.1.1, and its DHCP clients are from 192.168.1.100-x.x.x.199) Set the internet connection on the new router to "DHCP Client" Turn off the DHCP server & NAT routing on the new router Plug in a LAN cable from the original router into the LAN port #1 on the new router (NOT the WAN port, nothing is plugged in there) Reset the new router Afterwards, I try to ping 192.168.1.1 from the laptop plugged into LAN port #2 on the new router, with no response. 192.168.1.200 garners no response either. Typing "ipconfig" tells me: Autoconfiguration IP Address: 169.254.198.113 Subnet Mask: 255.255.0.0 Default Gateway: 169.254.198.113 What's going wrong? I appreciate any help!

  Read the article

• Best dual band A/B/G/N wireless router/ap for Linux

  - by Kevin Bowling

  Hello, I am looking for the best A/B/G/N dual band (simultaneous) router or access point that can be flashed with community firmware like dd-wrt or openwrt. In the past I have used the WRT54G series from Linksys with great success as access points and bridges. The WRT610N looks nice but I'm not sure how well the community firmwares support it. I am open to any manufacturer and any input or experience would be appreciated.

  Read the article

• Virtual Box Networking; How to configure bridged networking on Windows 7

  - by Krist van Besien

  I have VirtualBox on Windows 7. I have two virtual machines running RHEL, that work fine when the network is set to NAT. However I want to change the network adapters for the VM's to bridged in stead of NAT. However when I go in to the VM configuration, and select bridged I also need to select an adapter, but there is nothing to select. Apparently I need to install a separate driver/filter on the network adapter. However I don't know where to start. I reinstalled VirtualBox (latest version) but did not see an option to install such driver. What should I do?

  Read the article

• wireless router on LAN

  - by Scott

  Hi, Can I put a wireless router (for a laptop to talk to) which is configured to use DHCP on our work LAN ? I just need the laptop to be able to talk to the internet. Will it automatically get the gateway information when it is assigned an IP via DHCP ? Thanks Scott

  Read the article

• email spam filering in bridging

  - by User4283

  I've a mail server, which handle multiple domains. Due to concern of spam and mail server performance. I've configured another machine which will be in bridging and mail server would be behind that it. How can i filter spam emails in bridging server without running any smtp services. Scenario Internet +------+ Spamfilter Server (in bridging mode) +---------+ MailServer SmartHost will work for outgoing email. In this scenario i can filter all incoming emails. There is also another option of DNS which i don't want to use.

  Read the article

• Hardware needed to route between two networks over wireless

  - by AptDweller

  I recently rented an apartment about 100 yards from my brother's house. I have line of sight to his house and can pick up his home AP signal with one of my two laptops if I go out on my balcony (facing his house) or put the laptop by the window. The other laptop will sometimes see the SSID broadcast, but fails to connect, drops, etc. We would like to set up a persistent wireless connection between our homes. We would prefer each network be logically segmented as independent networks, but he will share his internet connection. I've got a bunch of tv shows saved to a NAS by my TiVO that I'd like to make available to him across the wireless link. My brother strongly prefers to not mess with his WAP at all. His network is running fine and is afraid to mess it up. I guess you could say he is "technologically declined". If we can get a reliable 11Mbps connection we will be satisfied. What hardware do I need to make this work? I was thinking a router with two wireless interfaces (external antennas) a wired interface, and a directional antenna mounted on my balcony facing his house. Can anyone recommend hardware to make this happen? Cheaper is better. I'll only be living in the area a year or two. I do have an old satellite TV antenna if that can be used to direct the signal.

  Read the article

• When I restart my LXC environment, the container does not re-bind to the IP address

  - by RoboTamer

  The IP does no longer respond to a remote ping With restart I mean: lxc-stop -n vm3 lxc-start -n vm3 -f /etc/lxc/vm3.conf -d -- /etc/network/interfaces auto lo iface lo inet loopback up route add -net 127.0.0.0 netmask 255.0.0.0 dev lo down route add -net 127.0.0.0 netmask 255.0.0.0 dev lo # device: eth0 auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.22.189.58 netmask 255.255.255.248 gateway 192.22.189.57 broadcast 192.22.189.63 bridge_ports eth0 bridge_fd 0 bridge_hello 2 bridge_maxage 12 bridge_stp off post-up ip route add 192.22.189.59 dev br0 post-up ip route add 192.22.189.60 dev br0 post-up ip route add 192.22.189.61 dev br0 post-up ip route add 192.22.189.62 dev br0 -- /etc/lxc/vm3.conf lxc.utsname = vm3 lxc.rootfs = /var/lib/lxc/vm3/rootfs lxc.tty = 4 #lxc.pts = 1024 # pseudo tty instance for strict isolation lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.mtu = 1500 #lxc.cgroup.cpuset.cpus = 0 # security parameter lxc.cgroup.devices.deny = a # Deny all access to devices lxc.cgroup.devices.allow = c 1:3 rwm # dev/null lxc.cgroup.devices.allow = c 1:5 rwm # dev/zero lxc.cgroup.devices.allow = c 5:1 rwm # dev/console lxc.cgroup.devices.allow = c 5:0 rwm # dev/tty lxc.cgroup.devices.allow = c 4:0 rwm # dev/tty0 lxc.cgroup.devices.allow = c 4:1 rwm # dev/tty1 lxc.cgroup.devices.allow = c 4:2 rwm # dev/tty2 lxc.cgroup.devices.allow = c 1:9 rwm # dev/urandon lxc.cgroup.devices.allow = c 1:8 rwm # dev/random lxc.cgroup.devices.allow = c 136:* rwm # dev/pts/* lxc.cgroup.devices.allow = c 5:2 rwm # dev/pts/ptmx lxc.cgroup.devices.allow = c 254:0 rwm # rtc # mounts point lxc.mount.entry=proc /var/lib/lxc/vm3/rootfs/proc proc nodev,noexec,nosuid 0 0 lxc.mount.entry=devpts /var/lib/lxc/vm3/rootfs/dev/pts devpts defaults 0 0 lxc.mount.entry=sysfs /var/lib/lxc/vm3/rootfs/sys sysfs defaults 0 0

  Read the article

• need advice on data center move, communication with both facilities during transition

  - by Brian Roden

  We are beginning the process of moving to a new facility. Office and warehouse operations will both be moving, and we must get shipping operations up and running at the new location while continuing to ship from the old location. Our contract with some third-party warehouse tenants requires two business day turnaround (only weekends and holidays excluded), so we can't have major downtime during the move. We would like to keep our 172.16.60/61.xxx internal address space in use throughout the move. Is it possible to keep using this same internal range, and have our existing WatchGuard Firebox 520 and whatever router we get for the other location (preferably the same model) just treat both locations as one network, leaving our host IPs the same throughout the move? Renumbering the servers when they move isn't a big deal, but our wireless terminals for order picking in the warehouse have fixed IPs (and a fixed IP, non-DNS reference to the host they speak with) and would be a massive undertaking to reconfigure when the servers move (each device would have to be reconfigured at least 2 times -- some when we start using them in the new building and the host is still here, all of them in both locations when the host moves to the new building, and the rest when they finally make the move to the new building). We're trying to avoid that if possible.

  Read the article

• Wireless network relay?

  - by IPX Ares

  Is there hardware (links would be great) that can connect to the wireless internet already in my house and provide hard links to other hardware? Basically the problem is that my basement is not wired up to let me hook up my cable modem. I have some electronics that do not have wireless and need a LAN wire. Is there something I could plug in downstairs to act as a relay hub?

  Read the article

• Bridging wlan0 to eth0

  - by user46127

  On arch Linux, I would like to mainly have eth0 (connected to bridged router) share the connection recieved from wlan0, Ive read tutorials but I'm not command sabby as other users are and don't completely understand. I would appreciate some help! Ty!

  Read the article

• Sharing internet connection from Windows XP using wi-fi router

  - by Darius

  Hi, I have an network configuration like: Ethernet cable from ISP connected to Windows XP machine, configured with static IP 192.168.0.3 Another ethernet connection from 2nd Windows XP machine's network adapter to a Wi-Fi router (D-Link Airport G+) XP set to "Share internet connection", the 2nd adapter configured as static to 192.169.0.1 D-Link Airport Wi-Fi router also configured as "static connection", it's IP set to 192.169.0.2, default gateway set to 192.169.0.1. Network mask everywhere is 24. Laptop computer connected with the router with static IP 192.169.0.3 The problems are: XP machine sees the router (it's able to ping it and access it via the web admin tool) The router somehow cannot PING the XP machine (using the tool provided by the web-based admin tool) The laptop computer cannot ping anything and cannot be pinged The router is only accessible when the ethernet cable is connected with a router's 1-4 LAN port, when I connect it via "WAN" port (which I believe is the proper one) it's not visible from the XP machine If you have similar experience with configuring a network like this I would really appreciate your help. I cannot use the Wi-Fi router with the ISP cable itself.

  Read the article

• Issue with multiple bridging for KVM hosts

  - by Henry-Nicolas Tourneur

  I'm using KVM and libvirt on my host (Debian lenny) + 2 bridges per guest (one for mgmt, one for public traffic). That setup isn't stable at all, sometimes I can do pings to a management ip, sometimes not. I don't know if my bridging paramateres are correct, could you check ? or if there is anything wrong ... Please also note that interface on guest doesn't flap and that I got not logs on my host. Of course forwarding is enabled. iface eth3 inet manual auto bond0 iface bond0 inet manual slaves eth1 eth2 pre-up ip link set bond0 up down ip link set bond0 down auto br0 iface br0 inet static address 10.160.0.7 netmask 255.255.255.128 bridge_ports eth3 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br0:1 iface br0:1 inet static address 10.160.0.9 netmask 255.255.255.128 auto br0:2 iface br0:2 inet static address 10.160.0.10 netmask 255.255.255.128 auto br1 iface br1 inet static address 217.4.40.242 netmask 255.255.255.240 gateway 217.4.40.241 pre-up /etc/network/firewall start bridge_ports bond0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br1:1 iface br1:1 inet static address 217.4.40.252 netmask 255.255.255.240 auto br1:2 iface br1:2 inet static address 217.4.40.253 netmask 255.255.255.240

  Read the article

• wireless ethernet adapter with EAP-PEAP?

  - by Joseph

  We have a wireless network set up to support WPA or WPA2 with AES or TKIP encryption and EAP-PEAP authentication. Users are wanting to connect devices that don't have the ability to do EAP-PEAP but have ethernet ports. I have found a wireless printer server that can do this, but I have yet to find a wireless ethernet adapter that can. Has anyone seen one with this ability?

  Read the article

• Connect ADSL modem SMC7904WBRA-N to CISCO RV082

  - by Cy.

  I have a SMC7904WBRA-N ADSL modem/router that connects to the internet with a static IP given by the provider. I've received a RV082 to create a VPN connection which is having problems to connect to the remote VPN Server. After many tries we deduced that the SMC7904WBRA-N is being problematic with the NAT and I have been suggested to put the SMC router into the appropriate DSL bridging mode so the RV082 gets direct access to internet with the static IP. Can you give me any hints on how could this be done? Which mode is that?

  Read the article

• Virtual firewall to protect hypervisor

  - by manutenfruits

  I am running an Ubuntu Server 12.10 as a single host connected to a NATed router connected using PPPoE to a optical fiber modem. This server is meant to be accessed from the Internet, but also to be used from the LAN as a SVN, MySQL and what not... The issue is that the router is not customizable enough to serve, so I was thinking about creating a virtual pfSense firewall using KVM inside of the server itself, removing the need of the router. Is this possible? Can the host ignore and block all traffic coming to itself, but not for the firewall? I am aware this is not the most desirable environment, I accept suggestions based on budget!

  Read the article

• ClearOS transparent firewall and web proxy mode possible?

  - by Scott Szretter

  In other firewall software packages I have seen the ability and am hoping it is possible with ClearOS to put it in to transparent or bridged mode where the device sits physically between the client workstations and the internet router, but is the client workstation has the internet router address as it's gateway, not the clearos machine. The client workstation would also not have to enter an http proxy address as that would be transparent. Is this possible and how do you configure ClearOS this way? Thanks!

  Read the article

• How to force my laptop to use the discrete GPU?

  - by Anton Roth

  My laptop (Asus X7BSV) is stuck using only the integrated GPU. It has a nVidia GT540M as well, but I cannot get it to work. I am using a Windows 7 x64 with latest drivers. This occurred after I attached an external USB monitor I need for work, and since then I cannot swap back to the nVidia GPU (dxdiag for example says that the primary GPU is the Intel integrated one). Asus support asked me to completely reinstall the system, but that is something I do not want to do. I checked the BIOS, there is no option as to what GPU to use. The nVidia card itself is working, since I can use CUDA on it, and it worked with a Ubuntu Live CD. In the nVidia software management I tried setting it to global setting, high performance GPU (nVidia), but that had no impact. What am I missing here? I did uninstall/delete all drivers and software related to the external monitor, but that did not help.

  Read the article

• How to set up my network/bridging using Apple Airport equipment?

  - by John

  I'd like to set up my network like this, and I want to make sure it's possible using the hardware I have. I think it should be... I've got my cable modem in one room. I want to plug it into an Apple Airport Express and create my wireless my wireless network here. The airport express will do the NAT and DHCP. By my TV there are a few things to be networked (Xbox and Tivo). I have an airport extreme here. I'd like to have the airport extreme join the wireless network and share the connection to the ethernet ports. Can anyone provide some assistance on the best way to configure to do this? Thanks!

  Read the article

• setting up bridged adapter for VPN server

  - by B. VB.

  I have an Ubuntu linux Linode server that I am trying to install OpenVPN on. I'm following the tutorials (which, it turns out, are quite incomplete). auto br0 iface br0 inet static address 192.168.0.10 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off When I add this chunk in my /etc/network/interfaces, and I restart networking, my eth0 interface does not have an IP and I cannot get on the network (I need to use a buggy, slow, and annoying AJAX term to do damage repair). Why does adding this screw everything up? Any tips on how to set up this bridged adapter?? Thanks in advance!

  Read the article

• Openstack - Connectivity between instances on 2 separate nodes

  - by drcursor

  I have the following setup: 1 x Management Node (node A) 2 x Compute Nodes (node B & C) 1 x Volume Node (node D) Relevant configurations: VlanManager multi_host=true Node B[eth0=192.168.6.102;br100=10.1.0.6] Node C [eth0=192.168.6.103;br100=10.1.0.4] I can ping between instances on the same node,but not with instances in different nodes. If I run "brctl br100 eth0" , Instances can ping between nodes, but I loose conectivity on eth0 (192.168.6.102/192.168.6.103) What do I have to change to be able to ping instances between nodes while maintaining normal connectivity on eth0 ?

  Read the article

• Cisco 1242 WAP Bridging

  - by DanWake

  I'm looking to connect two facilities with a a pair of Cisco 1242 access points and am looking for advice on configuration. We have multiple VLANs running that will need to be passed through the connection, but otherwise a fairly simple setup. Any advice on best practices from security, reliability, and speed points of views?

  Read the article

• Media Encoder w\ Merge Files & SandyBridge Hardware Encoding Support

  - by GruffTech

  So i have a Z68 chipset that allows Quick Sync encoding on my i7 processor. I want a media encoder that supports both Hardware encoding and allows me to "merge files". My problem is Fraps breaks my recording into 4GB files. I need to stitch these files together & re-encode for Youtube ect, but i want to use the hardware encoding I paid for. I have not figured out how to do this on Handbrake or MediaEsspresso.

  Read the article

• Bridging two connections in windows 7

  - by Serban Razvan

  I have recently bought an Samsung UE32ES5500 and I want to connect it to the internet. Not wanting to buy an expensive Samsung wireless adapter for the TV, I've decided to use an ethernet cable. Because the Internet cable passes through underground to the bedroom and the TV is located in the living room, i decided to put a router in the bedroom, and receive it's signal in the living room using a windows 7 laptop. Afterwards I connected the laptop to the TV through an ethernet cable, and bridged the two connections in Network Connections in Control Panel on the laptop. The TV successfully finds the laptop (and the router I think) but still cannot connect to the internet. Does anyone knows a solution to this problem? (the connections must be bridged because I want to have only one network in the house)

  Read the article

• D-Link DIR-300 slows down / loses network

  - by basic6

  there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >