Search Results

Search found 1163 results on 47 pages for 'jeff goulette'.

Page 17/47 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• Linux IPv6: DHCP and /127 prefixes

  - by Jeff Ferland

  I've tried multiple pieces of DHCP client and software in attempting to setup a solution for allocating a /127 prefix to virtual machines so that each maintains its own layer 2 isolation. Because there would only be one host assigned to each network, a /64 is impractical. While the prefix size could reasonably be somewhere in the /64-127 range, the crux of the problem has been the same regardless of the software used in configuring: the DHCP call to bring up the interface uses the address advertised by DHCPv6 and inserts two routes: the /127 given by the router advertising packets and a /64 as well. Any thoughts on why I'm getting the additional route added across dhcp client vendors?

  Read the article

• Video card not detected in POST on initial boot.

  - by Jeff M

  I have a minor problem with my desktop computer after cleaning it out for dust. When I first boot up the computer, the video card does not get detected so I can't see anything. In POST, I'm getting the "can't detect video card" beeps. The boot sequence continues normally, just without video. However, if I restart it (using the restart button) anytime after POST, it would boot up normally. I have no reason to think that the motherboard, video card or PSU got damaged in the process. It was working fine before, works fine after resetting. Took all the necessary precautions while cleaning. On the initial boot, I can hear the video card's fan power up but immediately power down and try again one more time only to fail. After the beep, resetting gets everything running and sounding normally. I've reseated the card a couple of times and reset the BIOS but doesn't seem to help. I'm hoping I won't have to take it out and remove and reinstall everything again. Does anyone recognize these symptoms to know exactly what the problem is? My guess is that the video card isn't getting enough juice initially to be running stable to be detected. I just don't know what I did (or didn't do) to get it to be in this state. It's not a high priority thing for me at the moment, just means I have to always reset it after initially turning it on but will eventually remove everything and reinstall if it comes to that. I don't think the specs are relevant here but just in case, here's the relevant stuff: Motherboard: Gigabyte P35-DS3P Video: EVGA GeForce 8600 GTS PSU: Antec True Power Trio 650W Built ~2 years ago, still running well

  Read the article

• View Public Key in Domain Key for a Domain

  - by Josh

  Using Jeff's blog post I'm creating domain keys for my account. I wanted to verify the setup using Get or Host command with Bind for Windows but I'm lost one of the commands. I can see view the _domainkey. txt file with this command: host -t txt _domainkey.stackoverflow.com but I'm at a loss at how I'd find the selector record. Jeff points out it can be anything before the before the period in "._domainkey.domain.com" but how would I list all records if I didn't know the exact query name? Is there a wildcard I could use to view all TXT or all records under this section?

  Read the article

• How do I create a calendar appointment from an e-mail in Outlook 2011 for Mac?

  - by Jeff O

  How do I create a calendar appointment from an e-mail in Outlook 2011 for Mac? In Windows, the e-mail content and attachments are carried over just by dragging and dropping. Dragging and dropping on the Mac doesn't work. Is there any other function to take an e-mail and make it a calendar appointment? I'm trying to avoid emailing it to myself. Edit: Since someone went to the trouble to make email2task, is it safe to assume this feature is not available otherwise?

  Read the article

• Programatically Determine Exchange Attachment Limit

  - by Jeff Ballard

  Is there any way to query the exchange server to determine the maximum attachment file size? I'd be doing this in ASP.NET/C#. I'd like to be able to validate the file they want to attach is not over the limit before the user attempts to send the file to the server as opposed to having the server send back an exception when it attempts to attach the file and it discovers the file is too large. I've also posted this question about this on stackoverflow.com as well - I figured a sysadmin for Exchange may have an answer as well as a developer. Hopefully I do not incur the wrath of the stackexchange gods.

  Read the article

• Error mounting samba share, cannot mount block device xxxx read-only

  - by Jeff Ward

  After installing Ubuntu 12.04, I'm trying to mount a samba share from Windows under Linux, using a scripted command that's always worked, and the server hasn't changed. The error is as follows: $ mount -t cifs //<host>/<share> /media/<share> -o username=<user>,password=<pass> mount: block device //<host>/<share> is write-protected, mounting read-only mount: cannot mount block device //<host>/<share> read-only $ I've read a lot of discussions about permissions, but unfortunately, that wasn't the issue. I'm submitting my own answer below for reference, hope this helps someone else.

  Read the article

• password protect apache user directory using system passwords

  - by Jeff

  I have set up Apache to check user passwords using these modules: LoadModule authz_user_module modules/mod_authz_user.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule auth_basic_module modules/mod_auth_basic.so However, these modules require me to manually add everyone to a new password file (which requires every user to type in their password). Is there a way to have Apache check the system passwords, so that anyone who can ssh can use the same password for web login?

  Read the article

• Time issues on the Network -- How to find the Root Cause

  - by Jeff

  A number of application servers started erroring out in my domain. Troubleshooting led me to a missconfiguration of NTP. I fixed the issue, but I don't know how the issue arose in the first place. The only errors I can find are System Error: 1097 Source: useenv System Error: 1058 Source: useenv System Error: 1030 Source: useenv System Error: 1000 Source: mmc How else can I find out why NTP started acting up on my domain? Is there any troubleshooting steps to diagnose why my DC started pulling from a random timeserver with the wrong time? EDIT: Current issue actually remains: the two 2003 DCs are not syncing with the PDC (a 2k8 box). w32tm /resync -- The computer did not resync because no time data was available.

  Read the article

• Domain user cannot connect to Exchange

  - by Jeff

  I can login to the local PC and connect to Exchange server - on the same physical network if i log into the domain i cannot connect to the Exchange server. DNS / DHCP all functioning as expected. User has AD account with Domain Admin rights. Quite confusing!

  Read the article

• Suggestions? Password & Encrypted Read/Write File like a Mac (.dmg or .SparseBundle) also R/W on Windows, Ubuntu

  - by Jeff Drew

  For years I have used .dmg or .sparsebundle (Encrypted and Password Protected) to safely keep home directory backups on my Mac. Now, I am looking for a similar Full Permissions/Read/Write that maintains an encrypted, and password protected file that it Tri-Platform. I'd like to have the future ability to use it on Mac OS X, Windows 7/8, and Ubuntu (current releases+). I appreciate your recommendations. Thank you. (I like mounting a DMG and having a file directory structure that can be easily maintained and organized. When done, un-mounting the file.) (I've seen Windows tools to open encrypted DMG files? and I will explore these options, but with the desire to also keep the file accessible on on three OSes, someone might have additional suggestions.)

  Read the article

• Transport rule - Exchange 2010

  - by Jeff

  I have two transport rules on my exchange server. One is: > Apply rule to messages: From users that are 'outside the organization' > and when any of the recipients in the To or Cc fields is a member of > '[email protected]' Forward the messageto sender's manager > for moderation The second is: Apply rule to messages from a member of '[email protected]' and sent to users that are 'outside the organization' forward the message to the sender's manager for moderation. nointernetmail is a distribution group, and each user has the managed by set to there local manager. However these transport rules do not work, internet mail is still sent and received without issue. I have read various tutorials / articles of how to do this on sites such as msexchangeblog and even microsoft technet, however even after following the guides I am still unable to have this function properly. Any help is appreciated.

  Read the article

• Troubleshooting an overheating CPU

  - by Jeff Fry

  I & my father just recently put together a new PC. Specs below. From the very beginning, on boot it will often complain that the CPU is too hot. If I sit in BIOS and watch the CPU, it'll drop back down from red to blue (<72C), at which point I've tended to just boot into Windows...and haven't had any problems. In fact, I've played a couple hours straight of Skyrim at max settings, and not had any visible issues. That said, I've occasionally walked away & come back to find that it's crashed. Yesterday, it crashed (while idle) twice in 12 hours, which shifted the balance from busy-with-life to nervous-I'm-about-to-melt-something. I just installed Core Temp which is showing my 4 cores fluxuating between 70-98C. I'm guessing at this point that the CPU fan may be incorrectly installed or defective. My first thought is to either (a) add water cooling (which the case supports) and / or (b) replace the CPU fan with an after-market one. That said, I'm very open to suggestions. A note, while I certainly don't want to burn money here, I have a baby coming any day now and am still unpacking from a recent move so if I have a choice between an option that costs money and another that takes a while...I'll happily spend a bit extra. Side question: Should I be nervous to even have this on at this point? Let me know if there's something useful I could add to my report. Otherwise, I'm looking forward to your suggestions! Thanks. CPU Intel i7-2600 CPU w/ stock fan Other HW ASUS P8Z68-V Pro motherboard 64G SSD boot drive 4 older SATA HDs GIGABYTE ATI Radeon HD6950 1 GB DDR5 8G Kingston T1 Series RAM Corsair 650W Gold Certified power supply Antec P280 case

  Read the article

• Rackspace Cloud Sites API (Not Cloud Servers)

  - by Jeff

  I'm looking for a way to pull data from my Rackspace Cloud SITES account. The data I want to pull is bandwidth, diskspace, and compute cycles (all available from control panel). I'd like to set up my own warning system, to be notified if I'm close to my limits on any given month. Does anyone know of a way/API to do this?

  Read the article

• How do I prevent a tar pipe from causing swapping?

  - by Jeff Shattock

  I have a rather large filesystem that I need to transfer from one Linux server to another. I figured the best way to do this was via a tar/netcat pipe arrangment, something like tar c . | pv | nc blah blah blah And it works great, the network stays fairly saturated, life is good. Until the source machine starts swapping. The files are on a raid on the source system, so the read speed is much faster than the write speed on the other end. Since the dest machine hasnt picked up the data yet, the source machine needs to stick it somewhere, so into RAM it goes, until there is no more free RAM. It then starts swapping, which is horribly painful since that machine has its OS installed on a somewhat slow CF card. Both machines have 4GB of physical ram, 64 bit Ubuntu 9.04 server. GigE link between them. How do I prevent this swapping? Can I put a "speed-limit" on the tar or netcat process so that the transfer speed doesn't overwhelm the write throughput on the destination end? The man pages didn't list anything, but there might be something I'm overlooking.

  Read the article

• How do I update my servers' domain name for Reverse DNS?

  - by Jeff

  I'm updating my mail servers' rDNS and I think I have it all figured out except for one thing. When I installed my OS (Debian Etch), the installer asked me to enter the "domain name". Is the "domain name" updated by using the hostname command? If so, which config file(s) are updated when using the hostname command? If not, how do I change my servers' domain name? My current /etc/hosts: 127.0.0.1 localhost 67.228.178.164 mrspock.example-old.com mrspock My current /etc/hostname: mrspock $ hostname -f mrspock.example-old.com I need to update hostname -f to be mrspock.example-new.com.

  Read the article

• What Device/System to use as a "router on a stick"

  - by Jeff Leyser

  I need to create several distinct VLANs, and provide a way for traffic to move between them. A "router on a stick" approach seems ideal: Internet | Router with Trunking Capability ("router on a stick") * * Trunk between router and switch * Switch with Trunking Capability | | | | | | | | | | | LAN 2 | LAN 4 | | 10.0.2.0/24 | 10.0.4.0/24 | | | | LAN 1 LAN 3 LAN 5 10.0.1.0/24 10.0.3.0/24 10.0.5.0/24 We have trunk-capable Layer-2 switches. The question is what to use as the router on a stick. My choices seem to be: 1) Use an existing Cisco 5505 ASA firewall. It appears the ASA can do the routing, but it's a 100Mbps device, and so seems sub-optimal at best 2) Buy a router. This seems overkill. 3) Buy a Layer-3 switch. Also seems overkill. 4) Use an existing Linux Box as a router 5) Use a new Linux box as a router' 6) Something I'm not thinking of I think either (4) or (5) is my best option, but I'm not sure how to choose between them. I expect the amount of traffic that has to cross the VLANs to be somewhat small, but bursty. How much load does routing add to a CentOS machine?

  Read the article

• Printer Properties not sending the correct page size to program

  - by Jeff

  We have a Zebra 2844 Label Printer with 4"x3" labels in it. When we check the page settings in Windows XP, it is set to the correct size. When we go to print out of any program, it prints 4"x11". I have checked the page settings in one of the programs that we are using and it does show correctly the 4"x3" settings but prints at the incorrect 4"x11". I have followed the steps here Paper size: Printer Properties vs Page Setup and here Is there a way to programatically set the printer properties in windows? but have not been able to glean enough information to figure it out. If anyone can help, I would appreciate it!

  Read the article

• Blocking IP address with port forwarding

  - by Jeff Storey

  I have a website setup behind a router, so the router has the external facing address and it will forward requests to the webserver inside the network. If there are X number of invalid login attempts, that IP address will be blocked from logging in. The problem is that because the site is being accessed through port forwarding, all requests show up as though they are coming from the router address, and thus the router address becomes the blocked IP. I'm not sure if this is a limitation of the router (linksys wrt160n) or if this a more general issue. Is there a way to handle this?

  Read the article

• Best DSL hardware for ADSL Troubleshooting

  - by Jeff Sacksteder

  I have a situation where I need to make the best of a bad DSL situation. The CPE is a black box with no access to DSL diagnostics. My plan is to get some sort of DSL hardware that exposes link-layer state and gives me knobs to tweak. I'd like to be able to mitigate bufferbloat as much as I can while I'm at it. The obvious choice would seem to be a Sangoma card in a linux system. I have no way of knowing if that will do anything for me without testing it, however. I have no other access to WAN troubleshooting equipment. Are there any other options avail to me as a consumer?

  Read the article

• Cannot write to directory after taking ownership

  - by jeff charles

  I had a directory on an internal hard-drive that was created in an old Windows 7 install. After re-installing my operating system, when I try to create a new directory inside that directory, I get an Access Denied message. This isn't a protected directory, just a random directory I created at the drive root (that drive was not the C drive in either install). I tried to take ownership by opening folder properties, going to the Security tab, clicking on Advanced, going to Owner tab, clicking on Edit, selecting my user account, checking Replace owner on subcontainers and objects, and clicking Apply. There were no error messages and I closed the dialogs. I rebooted, checked the owner on that folder and a couple subfolders and it appears to be set correctly. I am still getting an Access Denied message however when trying to create a directory in it. I've also tried using attrib -R . to remove any possible readonly attribute inside the directory in an admin command prompt but am still unable to create a directory using a non-admin prompt (it does work in an admin prompt). Is there anything I can do to get write access to that folder and it's subcontents in a non-elevated context without disabling UAC?

  Read the article

• Access Denied Error in PagesListCPVEventReceiver post SharePoint SP2 upgrade

  - by Jeff

  I am seeing the following errors from one of the SharePoint Web Front Ends after the SP2 upgrade. Has anyone else seen this error or a solution? Event Type: Error Event Source: Windows SharePoint Services 3 Event Category: General Event ID: 6875 Date: 2009-10-27 Time: 13:09:57 User: N/A Computer: XXXXXXX Description: Error loading and running event receiver Microsoft.SharePoint.Publishing.PagesListCPVEventReceiver in Microsoft.SharePoint.Publishing, Version=12.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429c. Additional information is below. : Access is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED)) For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• Managing service passwords with Puppet

  - by Jeff Ferland

  I'm setting up my Bacula configuration in Puppet. One thing I want to do is ensure that each password field is different. My current thought is to hash the hostname with a secret value that would ensure each file daemon has a unique password and that password can be written to both the director configuration and the file server. I definitely don't want to use one universal password as that would permit anybody who might compromise one machine to get access to any machine through Bacula. Is there another way to do this other than using a hash function to generate the passwords? Clarification: This is NOT about user accounts for services. This is about the authentication tokens (to use another term) in the client / server files. Example snippet: Director { # define myself Name = <%= hostname $>-dir QueryFile = "/etc/bacula/scripts/query.sql" WorkingDirectory = "/var/lib/bacula" PidDirectory = "/var/run/bacula" Maximum Concurrent Jobs = 3 Password = "<%= somePasswordFunction =>" # Console password Messages = Daemon }

  Read the article

• How can I find out which service is keeping Vista from restarting?

  - by Jeff

  Running Vista on my Toshiba laptop for several years now. Recently, I noticed it will not restart - I have to power cycle it. I have enabled Verbose Status messages, so I know it's stuck at "Stopping services". Is there a way to figure out which service is not stopping? I'm hoping for some kind of log like the bootlog. I've tried looking through the event viewer - no luck there.

  Read the article

• ownership of hard drive recoveery of files Windows 7

  - by Jeff

  Here is the issue. I have an old laptop that died that was running xp. I now have a win 7 laptop. I need to get the files off the old drive. Win 7 will not let me take ownership of the drive. I can runn the comand prompt in regular mode and do a dir on the drive that shows up as Q: drive in regular mode. I gives me the volume as c and the serial number. I can not take ownership in regular mode with the comand prompt or other means. Microsoft site says use safe mode with networking. So I go to safe mode the drive shows up as G: in safe mode. I use the comand prompt Takeown /f G: and get the device is not ready error. I am at a loss. All I want is to retrieve my files from this drive. Any ideas or sugestions. I don't see how you can dir and get some info in one mode and not acces it in another. I have to get ownership and permissions fixed to get in the drive to get my files. Thanks in advance. I might add that I am using a usb3.0 to ide/sata cable adapter. Software came with the device but I can't make heads or tails out of the manual to know if any of the software can help me. The soft ware is PCClone Ex lite, and Clone Drive Soft ware

  Read the article

• Upgrade CentOS 5.2 to 5.3 -- but not 5.4

  - by Jeff Leyser

  Server currently running CentOS 5.2. Developers tell me they'd like the machine upgrade to CentOS 5.3 -- but not all the way to CentOS 5.4, as they haven't tested with 5.4 yet. I'm pretty sure a yum upgrade will put me at 5.4, as a yum check-update shows all sorts of 5.4 packages. So how do I move up to 5.3?

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >