Search Results

Search found 12681 results on 508 pages for 'logical drive'.

Page 171/508 | < Previous Page | 167 168 169 170 171 172 173 174 175 176 177 178  | Next Page >

  • Adaptec 6405 RAID controller turned on red LED

    - by nn4l
    I have a server with an Adaptec 6405 RAID controller and 4 disks in a RAID 5 configuration. Staff in the data center called me because they noticed a red LED was turned on in one of the drive bays. I have then checked the status using 'arcconf getconfig 1' and I got the status message 'Logical devices/Failed/Degraded: 2/0/1'. The status of the logical devices was listed as 'Rebuilding'. However, I did not get any suspicious status of the affected physical device, the S.M.A.R.T. setting was 'no', the S.M.A.R.T. warnings were '0' and also 'arcconf getsmartstatus 1' returned no problems with any of the disk drives. The 'arcconf getlogs 1 events tabular' command gives lots of output (sorry, can't paste the log file here as I only have remote console access, I could post a screenshot though). Here are some sample entries: eventtype FSA_EM_EXPANDED_EVENT grouptype FSA_EXE_SCSI_GROUP subtype FSA_EXE_SCSI_SENSE_DATA subtypecode 12 cdb 28 00 17 c4 74 00 00 02 00 00 00 00 data 70 00 06 00 00 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 0 The 'arcconf getlogs 1 device tabular' command reports mediumErrors 1 for two of the disks. Today, I have checked the status of the controller again. Everything is back to normal, the controller status is now 'Logical devices/Failed/Degraded: 2/0/0', the logical devices are also all back to 'Optimal'. I was not able to check the LED status, my guess is that the red LED is off again. Now I have a lot of questions: what is a possible cause for the medium error, why it is not reported by the SMART log too? Should I replace the disk drives? They were purchased just a month ago. The rebuilding process took one or two days, is that normal? The disks are 2 TByte each and the storage system is mostly idling. the timestamp of the logs seem to show the moment of the log retrieval, not the moment of the incident. Please advise, all help is very appreciated.

    Read the article

  • Ubuntu 10.04 preseed unattended install results in faulty partition table

    - by joschi
    I'm currently trying to set up an unattended installation of Ubuntu 10.04 (Lucid Lynx) through preseeding. But whenever I try to create a custom partition scheme, the Debian installer (which Ubuntu is using) produces a faulty partition table. I've taken the partition scheme described in the example preseed file: d-i partman-auto/expert_recipe string \ boot-root :: \ 40 50 100 ext3 \ $primary{ } $bootable{ } \ method{ format } format{ } \ use_filesystem{ } filesystem{ ext3 } \ mountpoint{ /boot } \ . \ 500 10000 1000000000 ext3 \ method{ format } format{ } \ use_filesystem{ } filesystem{ ext3 } \ mountpoint{ / } \ . \ 64 512 300% linux-swap \ method{ swap } format{ } \ . Unfortunately it also produces an incorrect partition table on the disk. The installation process itself is working and the installed system eventually boots and is working, as far as I can tell. But fdisk and cfdisk are still complaining: # fdisk -l /dev/sda Disk /dev/sda: 17.2 GB, 17179869184 bytes 255 heads, 63 sectors/track, 2088 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000a1cdd Device Boot Start End Blocks Id System /dev/sda1 * 1 5 37888 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 5 2089 16736257 5 Extended /dev/sda5 5 2013 16121856 83 Linux /dev/sda6 2013 2089 613376 82 Linux swap / Solaris cfdisk even refuses to start at all: # cfdisk /dev/sda FATAL ERROR: Bad primary partition 1: Partition ends in the final partial cylinder parted on the other hand does not complain about the cylinder boundary of /dev/sda1: # parted /dev/sda p Model: VMware Virtual disk (scsi) Disk /dev/sda: 17.2GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 39.8MB 38.8MB primary ext4 boot 2 40.9MB 17.2GB 17.1GB extended 5 40.9MB 16.5GB 16.5GB logical ext4 6 16.6GB 17.2GB 628MB logical linux-swap(v1) Since the installed system is working, it shouldn't be a big problem but I'm afraid that this will mean trouble in the future.

    Read the article

  • fsck on LVM snapshots

    - by Alpha01
    I'm trying to do some file system checks using LVM snapshots of our Logical Volumes to see if any of them have dirty file systems. The problem that I have is that our LVM only has one Volume Group with no available space. I was able to do fsck's on some of the logical volumes using a loopback file system. However my question is, is it possible to create a 200GB loopback file system, and saved it on the same partition/logical volume that I'll be taking a snapshot of? Is LVM smart enough to not take a snapshot copy of the actual snapshot? [root@server z]# vgdisplay --- Volume group --- VG Name Web2-Vol System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 29 VG Access read/write VG Status resizable MAX LV 0 Cur LV 6 Open LV 6 Max PV 0 Cur PV 1 Act PV 1 VG Size 544.73 GB PE Size 4.00 MB Total PE 139450 Alloc PE / Size 139450 / 544.73 GB Free PE / Size 0 / 0 VG UUID BrVwNz-h1IO-ZETA-MeIf-1yq7-fHpn-fwMTcV [root@server z]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.7G 3.6G 5.6G 40% / /dev/sda1 251M 29M 210M 12% /boot /dev/mapper/Web2--Vol-var 12G 1.1G 11G 10% /var /dev/mapper/Web2--Vol-var--spool 12G 184M 12G 2% /var/spool /dev/mapper/Web2--Vol-var--lib--mysql 30G 15G 14G 52% /var/lib/mysql /dev/mapper/Web2--Vol-usr 13G 3.3G 8.9G 27% /usr /dev/mapper/Web2--Vol-z 468G 197G 267G 43% /z /dev/mapper/Web2--Vol-tmp 3.0G 76M 2.8G 3% /tmp tmpfs 7.9G 92K 7.9G 1% /dev/shm The logical volume in question is /dev/mapper/Web2--Vol-z. I'm afraid if I created the loopback file system in /dev/mapper/Web2--Vol-z and take a snapshot of it, the disk size will be trippled in size, thus running out of disk space available.

    Read the article

  • I flashed my DS4700 with a 7 series firmware, now my DS4300 cannot read the disks I moved to that lo

    - by Daniel Hoeving
    In preparation for adding a number of 1Tb SATA disks to our DS4700 I flashed the controller firmware from a 6 series (which only supports up to 2Tb logical drives) to a 7 series (which supports larger than 2Tb logical drives). Attached to this DS4700 was a EXP710 expansion drawer that we had planned to migrate out to our co-location to allieviate the storage issues we were having there. Unfortunately these two projects were planned in isolation to one another so I was at the time unaware of the issue that this would cause. Prior to migrating the drawer I was reading the "IBM TotalStorage DS4000 EXP700 and EXP710 Storage Expansion EnclosuresInstallation, User’s, and Maintenance Guide" and discovered this: Controller firmware 6.xx or earlier has a different metadata (DACstore) data structure than controller firmware 7.xx.xx.xx. Metadata consists of the array and logical drive configuration data. These two metadata data structures are not interchangeable. When powered up and in Optimal state, the storage subsystem with controller firmware level 7.xx.xx.xx can convert the metadata from the drives configured in storage subsystems with controller firmware level 6.xx or earlier to controller firmware level 7.xx.xx.xx metadata data structure. However, the storage subsystem with controller firmware level 6.xx or earlier cannot read the metadata from the drives configured in storage subsystems with controller firmware level 7.xx.xx.xx or later. I had assumed that if I deleted the logical drives and array information on the EXP710 prior to migrating it to the DS4300 (6.60.22 firmware) this would satisfy the above, unfortunately I was wrong. So my question is a) Is it possible to restore the DAC information to its factory settings, b) What tool(s) would I use to accomplish this, or c) is this a lost cause? Daniel.

    Read the article

  • Finding a shared HDD attached to the network from my F-13 machine

    - by Ramy
    Sorry for the slew of n00bie questions, but here is one more. I recently partitioned my 1.5TB harddrive according to this question I then bought this to attach the harddrive to my network. The problem is, how do I navigate to the hard drive to move files over the network to the HDD. should this be moved to serverfault? update: the disk isn't even showing up when i call "fdisk -l" (as root). How can I mount it if I can't even find it? [root@Moonface ~]# /sbin/fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00018598 Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 19458 155777024 8e Linux LVM Disk /dev/dm-0: 53.7 GB, 53687091200 bytes 255 heads, 63 sectors/track, 6527 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/dm-1: 4764 MB, 4764729344 bytes 255 heads, 63 sectors/track, 579 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-1 doesn't contain a valid partition table Disk /dev/dm-2: 101.0 GB, 101032394752 bytes 255 heads, 63 sectors/track, 12283 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-2 doesn't contain a valid partition table

    Read the article

  • RAID6 mdraid -> LVM -> EXT4 root with GRUB2?

    - by Rotonen
    2012-03-31 Debian Wheezy daily build in VirtualBox 4.1.2, 6 disk devices. My steps to reproduce so far: Setup one partition, using the entire disk, as a physical volume for RAID, per disk Setup a single RAID6 mdraid array out of all of those Use the resulting md0 as the only physical volume for the volume group Setup your logical volumes, filesystems and mount points as you wish Install your system Both / and /boot will be in this stack. I've chosen EXT4 as my filesystem for this setup. I can get as far as GRUB2 rescue console, which can see the mdraid, the volume group and the LVM logical volumes (all named appropriately on all levels) on it, but I cannot ls the filesystem contents of any of those and I cannot boot from them. As far as I can see from the documentation the version of GRUB2 shipped there should handle all of this gracefully. http://packages.debian.org/wheezy/grub-pc (1.99-17 at the time of writing.) It is loading the ext2, raid, raid6rec, dosmbr (this one is in the list of modules once per disk) and lvm modules according to the generated grub.cfg file. Also it is defining the list of modules to be loaded twice in the generated grub.cfg file and according to quick Googling around this seems to be the norm and OK for GRUB2. How to get further by getting GRUB2 to actually be able to read the content of the filesystems and boot the system? What am I wrong about in my assumptions of functionality here? EDIT (2012-04-01) My generated grub.cfg: http://pastie.org/3708436 It seems it first makes my /usr logical volume the root and that might be source of the failure? A grub-mkconfig bug? Or is it supposed to get access to stuff from /usr before / and /boot? /boot is on / for me - no separate boot logical volume.

    Read the article

  • file system that allow to specify different RAID level per directory and change it afterward

    - by Adam Ryczkowski
    I have 5 hard drives, where I want to keep my data. Some of my files are more important, and some of them are less. So some of them I wish to put on RAID-6, and for some it RAID-5 is sufficient. It is difficult to predict at the moment of creation of the arrays how much space of each type to declare. What I would do if I didn't hear about zfs, is partition the hard drives into identical 100GB partitions, and as my needs grow, assemble those partitions into md devices using linux-raid. Then, I'd combine those devices using lvm into logical volumes where I'd put my data. So when I'd need more space of e.g. RAID-6, I'd take 100GB partition from each hard drive and assemble them into another RAID-6 md device and would use it as physical storage for the logical volume group dedicated for RAID-6 data. Then I could grow the file system on this logical volume. On top of RAID-6 and RAID-5 Volume Groups (managed by lvm) would reside completely independent file systems, which I'd later merge with multiple mount --bind into a single directory structure that would reflect the logical structure of data rather that of the storage. But now, when I heard about the ZFS with all the performance, data-healing and compression capabilities I cannot stop thinking if it can help me. If so, what do you think would be the best setup?

    Read the article

  • Relayout LVM Disk

    - by Tom
    I have an Ubuntu 11.10 system with two 500GB disks. The partition tables look like this: /dev/sda1 primary 465.52GB /dev/sda2 extended 243.17MB -> /dev/sda5 logical 243.14MB /dev/sdb1 primary 465.76GB sda1 and sdb1 are in a single LVM physical volume group containing a single logical volume containing a single logical filesystem which is mounted as /. sda5 is mounted as /boot. The problem comes when I want to upgrade to Ubuntu 12.04, which requires at least 247MB free on /boot. So I need to reduce the size of sda1 so that I can increase the size of sda2 and sda5. How the heck do I do that? I can find how to shrink the logical volume group, but I'm not at all clear on how to clear out the end part of sda1 so that I can reduce the physical volume group. Does pvresize just deal with this automagically? Or is that wild wishful thinking? I guess the alternatives are to back everything up onto something or other and recreate the thing from scratch or find out whether GRUB2 supports using LVM for /boot.

    Read the article

  • disk partition centos

    - by FlourishDNA
    I am setting up server for hosting two WordPress which has size of around 70GB. I have already installed CentOS as OS and I would like to partition the Disk. Is there any tool which can help me or can someone guide me though the process as I am not expert is SSH commands. Here are some output that might help. OS: CentOS release 6.3 fdisk -l Disk /dev/xvdb: 214.7 GB, 214748364800 bytes 255 heads, 63 sectors/track, 26108 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b91e0 Device Boot Start End Blocks Id System Disk /dev/xvda: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e542c Device Boot Start End Blocks Id System /dev/xvda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvda2 64 2611 20458496 8e Linux LVM Disk /dev/mapper/vg_flourish-lv_root: 16.7 GB, 16718495744 bytes 255 heads, 63 sectors/track, 2032 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_flourish-lv_swap: 4227 MB, 4227858432 bytes 255 heads, 63 sectors/track, 514 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 df Filesystem 1K-blocks Used Available Use% Mounted on /dev/mapper/vg_flourish-lv_root 16070076 758184 14495560 5% / tmpfs 958500 0 958500 0% /dev/shm /dev/xvda1 495844 31926 438318 7% /boot df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_flourish-lv_root 16G 741M 14G 5% / tmpfs 937M 0 937M 0% /dev/shm /dev/xvda1 485M 32M 429M 7% /boot Thanks

    Read the article

  • Is it safe to format this partition?

    - by xanesis4
    On a ubuntu server I own, I am running out of space. When I ran sudo parted /dev/sda -l to find all available drives, I got this: Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 256MB 255MB primary ext2 boot 2 257MB 1000GB 1000GB extended 5 257MB 1000GB 1000GB logical lvm Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-swap_1: 2135MB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 2135MB 2135MB linux-swap(v1) Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-root: 998GB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 998GB 998GB ext4 I understand /dev/mapper/server--vg-root is the filesystem, and /dev/sda1 has some stuff related to GRUB. But, what about /dev/sda2 and /dev/sda5? When I tried to mount /dev/sda2, it said that I needed to specify the file system, which according to the table, is nonexistent. So, is it safe to format this with, say ext4 and mount it? Also, when I tried to mount /dev/sd5, it gave me this error: mount: unknown filesystem type 'LVM2_member' I assume it is NOT save to reformat this. If I'm wrong, then that would be great, because I could save some space. Please let me know either way. Thanks in advance! UPDATE: Here is the result of mount: /dev/mapper/server--vg-root on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda1 on /boot type ext2 (rw,acl) /dev/sda1 on /media/hd2 type ext2 (rw)

    Read the article

  • FileSystem.GetFiles() + UnauthorizedAccessException error?

    - by OverTheRainbow
    Hello, It seems like FileSystem.GetFiles() is unable to recover from the UnauthorizedAccessException exception that .Net triggers when trying to access an off-limit directory. In this case, does it mean this class/method isn't useful when scanning a whole drive and I should use some other solution (in which case: Which one?)? Here's some code to show the issue: Private Sub bgrLongProcess_DoWork(ByVal sender As System.Object, ByVal e As System.ComponentModel.DoWorkEventArgs) Handles bgrLongProcess.DoWork Dim drive As DriveInfo Dim filelist As Collections.ObjectModel.ReadOnlyCollection(Of String) Dim filepath As String 'Scan all fixed-drives for MyFiles.* For Each drive In DriveInfo.GetDrives() If drive.DriveType = DriveType.Fixed Then Try 'How to handle "Access to the path 'C:\System Volume Information' is denied." error? filelist = My.Computer.FileSystem.GetFiles(drive.ToString, FileIO.SearchOption.SearchAllSubDirectories, "MyFiles.*") For Each filepath In filelist DataGridView1.Rows.Add(filepath.ToString, "temp") 'Trigger ProgressChanged() event bgrLongProcess.ReportProgress(0, filepath) Next filepath Catch Ex As UnauthorizedAccessException 'How to ignore this directory and move on? End Try End If Next drive End Sub Thank you. Edit: What about using a Try/Catch just to have GetFiles() fill the array, ignore the exception and just resume? Private Sub bgrLongProcess_DoWork(ByVal sender As System.Object, ByVal e As System.ComponentModel.DoWorkEventArgs) Handles bgrLongProcess.DoWork 'Do lengthy stuff here Dim filelist As Collections.ObjectModel.ReadOnlyCollection(Of String) Dim filepath As String filelist = Nothing Try filelist = My.Computer.FileSystem.GetFiles("C:\", FileIO.SearchOption.SearchAllSubDirectories, "MyFiles.*") Catch ex As UnauthorizedAccessException 'How to just ignore this off-limit directory and resume searching? End Try 'Object reference not set to an instance of an object For Each filepath In filelist bgrLongProcess.ReportProgress(0, filepath) Next filepath End Sub

    Read the article

  • MySQL – How to Find mysqld.exe with Command Prompt – Fix: ‘mysql’ is not recognized as an internal or external command, operable program or batch file

    - by Pinal Dave
    One of the most popular question I get after watching my MySQL courses on Pluralsight is that beginning users are not able to find where they have installed MySQL Server. The error they receive is as follows when they type mysqld command on their default command line. ‘mysql‘ is not recognized as an internal or external command, operable program or batch file. This error comes up if user try to execute mysqld command on default command prompt. The user should execute this command where mysql.exe file exists.  If you are using Windows Explorer you can easily search on your drive mysqld.exe and find the location of the file and execute the above command there. However, if you want to find out with command prompt the location of mysqld.exe file you can follow the direction here. Step 1: Open a command prompt Open command prompt from Start >> Run >> cmd >> enter Step 2: Change directory You need to change the default directory to root directory, hence type cd\ command on the prompt to change the default directory to c:\ . Here we are assuming that you have installed MySQL on your c: drive. If you have installed it on any other drive change the drive to that letter. Step 3: Search Drive Type the command dir mysqld.exe /s /p on the command prompt. It will search your directories and will list the directory where mysqld.exe is located. Step 4: Change Directory Now once again change your command prompt file location to the folder where your mysqld.exe is located. In my case it is located here in folder C:\Program Files\MySQL\MySQL Server 5.6\bin hence I will run following command: cd C:\Program Files\MySQL\MySQL Server 5.6\bin . Step 5: Execute mysqld.exe Now you can once again mysqld.exe on your command prompt. You can use this method to search pretty much any file with the help of command prompt. Reference: Pinal Dave (http://blog.sqlauthority.com)Filed under: MySQL, PostADay, SQL, SQL Authority, SQL Query, SQL Tips and Tricks, T SQL

    Read the article

  • How To Disconnect Non-Mapped UNC Path “Drives” in Windows

    - by The Geek
    Have you ever browsed over to another PC on your network using “network neighborhood”, and then connected to one of the file shares? Without a drive letter, how do you disconnect yourself once you’ve done so? Really confused as to what I’m talking about? Let’s walk through the process. First, imagine that you browse through and connect to a share, entering your username and password to gain access. The problem is that you stay connected, and there’s no visible way to disconnect yourself. If you try and shut down the other PC, you’ll receive a message that users are still connected. So let’s disconnect! Open up a command prompt, and then type in the following: net use This will give you a list of the connected drives, including the ones that aren’t actually mapped to a drive letter. To disconnect one of the connections, you can use the following command: net use /delete \\server\sharename For example, in this instance we’d disconnect like so: net use /delete \\192.168.1.205\root$ Now when you run the “net use” command again, you’ll see that you’ve been properly disconnected. If you wanted to actually connect to a share without mapping a drive letter, you can do the following: net use /user:Username \\server\sharename Password You could then just pop \\server\sharename into a Windows Explorer window and browse the files that way. Note that this technique should work exactly the same in any version of windows. Similar Articles Productive Geek Tips Remove "Map Network Drive" Menu Item from Windows Vista or XPDisable the Annoying "This page has an unspecified potential security risk" When Using Files on a Network ShareCopy Path of a File to the Clipboard in Windows 7 or VistaMap a Network Drive from XP to Windows 7Defrag Multiple Hard Drives At Once In Windows TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Enable DreamScene in Windows 7 Microsoft’s “How Do I ?” Videos Home Networks – How do they look like & the problems they cause Check Your IMAP Mail Offline In Thunderbird Follow Finder Finds You Twitter Users To Follow Combine MP3 Files Easily

    Read the article

  • ODI 12c's Mapping Designer - Combining Flow Based and Expression Based Mapping

    - by Madhu Nair
    post by David Allan ODI is renowned for its declarative designer and minimal expression based paradigm. The new ODI 12c release has extended this even further to provide an extended declarative mapping designer. The ODI 12c mapper is a fusion of ODI's new declarative designer with the familiar flow based designer while retaining ODI’s key differentiators of: Minimal expression based definition, The ability to incrementally design an interface and to extract/load data from any combination of sources, and most importantly Backed by ODI’s extensible knowledge module framework. The declarative nature of the product has been extended to include an extensible library of common components that can be used to easily build simple to complex data integration solutions. Big usability improvements through consistent interactions of components and concepts all constructed around the familiar knowledge module framework provide the utmost flexibility. Here is a little taster: So what is a mapping? A mapping comprises of a logical design and at least one physical design, it may have many. A mapping can have many targets, of any technology and can be arbitrarily complex. You can build reusable mappings and use them in other mappings or other reusable mappings. In the example below all of the information from an Oracle bonus table and a bonus file are joined with an Oracle employees table before being written to a target. Some things that are cool include the one-click expression cross referencing so you can easily see what's used where within the design. The logical design in a mapping describes what you want to accomplish  (see the animated GIF here illustrating how the above mapping was designed) . The physical design lets you configure how it is to be accomplished. So you could have one logical design that is realized as an initial load in one physical design and as an incremental load in another. In the physical design below we can customize how the mapping is accomplished by picking Knowledge Modules, in ODI 12c you can pick multiple nodes (on logical or physical) and see common properties. This is useful as we can quickly compare property values across objects - below we can see knowledge modules settings on the access points between execution units side by side, in the example one table is retrieved via database links and the other is an external table. In the logical design I had selected an append mode for the integration type, so by default the IKM on the target will choose the most suitable/default IKM - which in this case is an in-built Oracle Insert IKM (see image below). This supports insert and select hints for the Oracle database (the ANSI SQL Insert IKM does not support these), so by default you will get direct path inserts with Oracle on this statement. In ODI 12c, the mapper is just that, a mapper. Design your mapping, write to multiple targets, the targets can be in the same data server, in different data servers or in totally different technologies - it does not matter. ODI 12c will derive and generate a plan that you can use or customize with knowledge modules. Some of the use cases which are greatly simplified include multiple heterogeneous targets, multi target inserts for Oracle and writing of XML. Let's switch it up now and look at a slightly different example to illustrate expression reuse. In ODI you can define reusable expressions using user functions. These can be reused across mappings and the implementations specialized per technology. So you can have common expressions across Oracle, SQL Server, Hive etc. shielding the design from the physical aspects of the generated language. Another way to reuse is within a mapping itself. In ODI 12c expressions can be defined and reused within a mapping. Rather than replicating the expression text in larger expressions you can decompose into smaller snippets, below you can see UNIT_TAX AMOUNT has been defined and is used in two downstream target columns - its used in the TOTAL_TAX_AMOUNT plus its used in the UNIT_TAX_AMOUNT (a recording of the calculation).  You can see the columns that the expressions depend on (upstream) and the columns the expression is used in (downstream) highlighted within the mapper. Also multi selecting attributes is a convenient way to see what's being used where, below I have selected the TOTAL_TAX_AMOUNT in the target datastore and the UNIT_TAX_AMOUNT in UNIT_CALC. You can now see many expressions at once now and understand much more at the once time without needlessly clicking around and memorizing information. Our mantra during development was to keep it simple and make the tool more powerful and do even more for the user. The development team was a fusion of many teams from Oracle Warehouse Builder, Sunopsis and BEA Aqualogic, debating and perfecting the mapper in ODI 12c. This was quite a project from supporting the capabilities of ODI in 11g to building the flow based mapping tool to support the future. I hope this was a useful insight, there is so much more to come on this topic, this is just a preview of much more that you will see of the mapper in ODI 12c.

    Read the article

  • SQL SERVER – Example of Performance Tuning for Advanced Users with DB Optimizer

    - by Pinal Dave
    Performance tuning is such a subject that everyone wants to master it. In beginning everybody is at a novice level and spend lots of time learning how to master the art of performance tuning. However, as we progress further the tuning of the system keeps on getting very difficult. I have understood in my early career there should be no need of ego in the technology field. There are always better solutions and better ideas out there and we should not resist them. Instead of resisting the change and new wave I personally adopt it. Here is a similar example, as I personally progress to the master level of performance tuning, I face that it is getting harder to come up with optimal solutions. In such scenarios I rely on various tools to teach me how I can do things better. Once I learn about tools, I am often able to come up with better solutions when I face the similar situation next time. A few days ago I had received a query where the user wanted to tune it further to get the maximum out of the performance. I have re-written the similar query with the help of AdventureWorks sample database. SELECT * FROM HumanResources.Employee e INNER JOIN HumanResources.EmployeeDepartmentHistory edh ON e.BusinessEntityID = edh.BusinessEntityID INNER JOIN HumanResources.Shift s ON edh.ShiftID = s.ShiftID; User had similar query to above query was used in very critical report and wanted to get best out of the query. When I looked at the query – here were my initial thoughts Use only column in the select statements as much as you want in the application Let us look at the query pattern and data workload and find out the optimal index for it Before I give further solutions I was told by the user that they need all the columns from all the tables and creating index was not allowed in their system. He can only re-write queries or use hints to further tune this query. Now I was in the constraint box – I believe * was not a great idea but if they wanted all the columns, I believe we can’t do much besides using *. Additionally, if I cannot create a further index, I must come up with some creative way to write this query. I personally do not like to use hints in my application but there are cases when hints work out magically and gives optimal solutions. Finally, I decided to use Embarcadero’s DB Optimizer. It is a fantastic tool and very helpful when it is about performance tuning. I have previously explained how it works over here. First open DBOptimizer and open Tuning Job from File >> New >> Tuning Job. Once you open DBOptimizer Tuning Job follow the various steps indicates in the following diagram. Essentially we will take our original script and will paste that into Step 1: New SQL Text and right after that we will enable Step 2 for Generating Various cases, Step 3 for Detailed Analysis and Step 4 for Executing each generated case. Finally we will click on Analysis in Step 5 which will generate the report detailed analysis in the result pan. The detailed pan looks like. It generates various cases of T-SQL based on the original query. It applies various hints and available hints to the query and generate various execution plans of the query and displays them in the resultant. You can clearly notice that original query had a cost of 0.0841 and logical reads about 607 pages. Whereas various options which are just following it has different execution cost as well logical read. There are few cases where we have higher logical read and there are few cases where as we have very low logical read. If we pay attention the very next row to original query have Merge_Join_Query in description and have lowest execution cost value of 0.044 and have lowest Logical Reads of 29. This row contains the query which is the most optimal re-write of the original query. Let us double click over it. Here is the query: SELECT * FROM HumanResources.Employee e INNER JOIN HumanResources.EmployeeDepartmentHistory edh ON e.BusinessEntityID = edh.BusinessEntityID INNER JOIN HumanResources.Shift s ON edh.ShiftID = s.ShiftID OPTION (MERGE JOIN) If you notice above query have additional hint of Merge Join. With the help of this Merge Join query hint this query is now performing much better than before. The entire process takes less than 60 seconds. Please note that it the join hint Merge Join was optimal for this query but it is not necessary that the same hint will be helpful in all the queries. Additionally, if the workload or data pattern changes the query hint of merge join may be no more optimal join. In that case, we will have to redo the entire exercise once again. This is the reason I do not like to use hints in my queries and I discourage all of my users to use the same. However, if you look at this example, this is a great case where hints are optimizing the performance of the query. It is humanly not possible to test out various query hints and index options with the query to figure out which is the most optimal solution. Sometimes, we need to depend on the efficiency tools like DB Optimizer to guide us the way and select the best option from the suggestion provided. Let me know what you think of this article as well your experience with DB Optimizer. Please leave a comment. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Joins, SQL Optimization, SQL Performance, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

    Read the article

  • Cannot dual Windows XP and Ubuntu

    - by Fabio Machado
    I am new to Ubuntu and at the moment I am trying to get Ubuntu 12.10 to one of my machines. The machine is a Pentium 4 @ 3.06, 2Gb RAM, 200GB Hard Drive and a NVidia GeForce 8800 GT. A few days ago, I tried Ubuntu without installing and it worked perfectly. Yesterday, I decided to formatted the hard drive and divide my hard drive into four partitions: 1 for the XP, 1 for Ubuntu, 1 for swamp and 1 where I will have my documents. Everything went great, I installed XP and then Ubuntu but I did something wrong on the partition window (Ubunto partion window) that I ended up without boot loader. This morning, I formatted everything again, installed XP and when I went to install Ubuntu (with the same DVD as before) the problems started. First, I had a black screen with a msg written with white text saying something like: unable to find a medium containing a live file system. After I burned another CD and tried again, I got stuck at the red dots (loading screen). I then went online and I read somewhere that it could be the CD, so I checked the integrity of the CD and everything was fine. I also unplugged all USBs connected to the computer and nothing changed. I goggled further options to try to solve my problem and some users suggested that people having these types of problems should try the alternate installation, which if I am not wrong is for networks. I then tried to install and yes the installation process was different from the normal CD, but it did get stuck on a page where it was doing something, like: ...finding ethd0 and it was stuck on the 100%. I tried USB installation as well and it also got stuck at the red dots (I do not have USB 3.0 on the computer in question). I have burned 5 different CD's and all at low speed. I checked the integrity and all are fine. I downloaded other distribution as well as other versions of Ubuntu and I still cannot install or even run the Live CD of Ubuntu or any other distribution. What is really annoying me is that everything was working perfectly before, when I first tried to install Ubuntu. Anyway, any help is welcome. Edit: My boot load is normal, no errors and all the hardware is working fine. I forgot to mention that after the loading screen (red dots) gets stuck, the DVD drive and the hard drive goes into idle state. I also restored the default values of the BIOS and no luck.

    Read the article

  • Grub rescue - error: unknown filesystem

    - by user53817
    I have a multiboot system set up. The system has three drives. Multiboot is configured with Windows XP, Windows 7, and Ubuntu - all on the first drive. I had a lot of unpartitioned space left on the drive and was reserving it for adding other OSes and for storing files there in the future. One day I went ahead and downloaded Partition Wizard and created a logical NTFS partition from within Windows 7, still some unpartitioned space left over. Everything worked fine, until I rebooted the computer a few days later. Now I'm getting: error: unknown filesystem. grub rescue First of all I was surprised not to find any kind of help command, by trying: help, ?, man, --help, -h, bash, cmd, etc. Now I'm stuck with non-bootable system. I have started researching the issue and finding that people usually recommend to boot to a Live CD and fix the issue from there. Is there a way to fix this issue from within grub rescue without the need for Live CD? UPDATE By following the steps from persist commands typed to grub rescue, I was able to boot to initramfs prompt. But not anywhere further than that. So far from reading the manual on grub rescue, I was able to see my drives and partitions using ls command. For the first hard drive I see the following: (hd0) (hd0,msdos6) (hd0,msdos5) (hd0,msdos2) (hd0,msdos1) I now know that (hd0,msdos6) contains Linux on it, since ls (hd0,msdos6)/ lists directories. Others will give "error: unknown filesystem." UPDATE 2 After the following commands I am now getting to the boot menu and can boot into Windows 7 and Ubuntu, but upon reboot I have to repeat these steps. ls ls (hd0,msdos6)/ set root=(hd0,msdos6) ls / set prefix=(hd0,msdos6)/boot/grub insmod /boot/grub/linux.mod normal UPDATE 3 Thanks Shashank Singh, with your instructions I have simplified my steps to the following. I have learned from you that I can replace msdos6 with just a 6 and that I can just do insmod normal instead of insmod /boot/grub/linux.mod. Now I just need to figure out how to save this settings from within grub itself, without booting into any OS. set root=(hd0,6) set prefix=(hd0,6)/boot/grub insmod normal normal UPDATE 4 Well, it seems like it is a requirement to boot into Linux. After booting into Ubuntu I have performed the following steps described in the manual: sudo update-grub udo grub-install /dev/sda This did not resolve the issue. I still get the grub rescue prompt. What do I need to do to permanently fix it? I have also learned that drive numbers as in hd0 need to be translated to drive letters as in /dev/sda for some commands. hd1 would be sdb, hd2 would be sdc, and so on. Partitions listed in grub as (hd0,msdos6) would be translated to /dev/sda6.

    Read the article

  • Failure connecting to Dell MD3200i from XenServer 6.2 pool

    - by Tom Sparrow
    This question also asked at Citrix Forums http://forums.citrix.com/thread.jspa?threadID=332289 I have a MD3200i that is currently working fine with my Xen5.6 pool, but I cannot get a connection to the new 6.2 pool to work. I previously had a problem with a 6.0 upgrade (which is why the old pool is still on 5.6), but rolled back rather than fix it as it wasn't urgent at the time. This install is on new machines - I tried 6.1 first (which had the same problems) then 6.2 was released the second day after installation so I switched to that. I've not installed anything from the Dell resource DVD at this point - I can't find anything saying I should, and everything I have read suggests it shouldn't be necessary. I can ping all 8 ip addresses from both servers in the pool, iscsiadm -m discovery works fine, I can login to the nodes and iscsiadm reports the sessions active correctly. I've added the required sections to multipath.conf, but multipath -ll reports DM multipath kernel driver not loaded immediately after boot. The following is a log of a test session immediately after boot. root@xen3 ~]# iscsiadm -m node --loginall=all Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.101,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.101,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.104,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.102,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.103,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.104,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.102,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.103,3260] Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.101,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.101,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.104,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.102,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.103,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.104,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.102,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.103,3260]: successful [root@xen3 ~]# iscsiadm -m session tcp: [1] 192.168.130.101:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [2] 192.168.131.101:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [3] 192.168.131.104:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [4] 192.168.131.102:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [5] 192.168.130.103:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [6] 192.168.130.104:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [7] 192.168.130.102:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [8] 192.168.131.103:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 [root@xen3 ~]# service multipathd restart ok Stopping multipathd daemon: [ OK ] Starting multipathd daemon: [ OK ] [root@xen3 ~]# multipath Jul 04 09:58:47 | DM multipath kernel driver not loaded Jul 04 09:58:47 | DM multipath kernel driver not loaded [root@xen3 ~]# multipath -ll Jul 04 09:59:03 | DM multipath kernel driver not loaded Jul 04 09:59:03 | DM multipath kernel driver not loaded [ root@xen3 ~]# modprobe dm_multipath [root@xen3 ~]# multipath Jul 04 10:19:50 | 36b8ca3a0e7024800194a0bd11891cd14: ignoring map create: 1Dell_Internal_Dual_SD_0123456789AB undef Dell,Internal Dual SD size=1.9G features='0' hwhandler='0' wp=undef `-+- policy='round-robin 0' prio=1 status=undef `- 7:0:0:0 sdb 8:16 undef ready running [root@xen3 ~]# multipath -ll 1Dell_Internal_Dual_SD_0123456789AB dm-1 Dell,Internal Dual SD size=1.9G features='0' hwhandler='0' wp=rw `-+- policy='round-robin 0' prio=1 status=enabled `- 7:0:0:0 sdb 8:16 active ready running [root@xen3 ~]# iscsiadm -m session tcp: [1] 192.168.130.101:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [2] 192.168.131.101:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [3] 192.168.131.104:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [4] 192.168.131.102:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [5] 192.168.130.103:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [6] 192.168.130.104:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [7] 192.168.130.102:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [8] 192.168.131.103:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 [root@xen3 ~]# dmesg | tail -n 50 [ 1161.881010] sd 8:0:0:0: [sdf] Unhandled error code [ 1161.881013] sd 8:0:0:0: [sdf] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1161.881017] sd 8:0:0:0: [sdf] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1161.881024] end_request: I/O error, dev sdf, sector 0 [ 1161.881031] Buffer I/O error on device sdf, logical block 0 [ 1161.881045] sd 15:0:0:0: [sdi] Unhandled error code [ 1161.881048] sd 15:0:0:0: [sdi] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1161.881052] sd 15:0:0:0: [sdi] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1161.881058] end_request: I/O error, dev sdi, sector 0 [ 1161.881065] Buffer I/O error on device sdi, logical block 0 [ 1161.881122] sd 9:0:0:0: [sdg] Unhandled error code [ 1161.881124] sd 9:0:0:0: [sdg] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1161.881126] sd 9:0:0:0: [sdg] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1161.881132] end_request: I/O error, dev sdg, sector 0 [ 1161.881140] Buffer I/O error on device sdg, logical block 0 [ 1168.220951] connection6:0: ping timeout of 15 secs expired, recv timeout 10, last rx 84060, last ping 85060, now 86560 [ 1168.220957] connection7:0: ping timeout of 15 secs expired, recv timeout 10, last rx 84060, last ping 85060, now 86560 [ 1168.220967] connection7:0: detected conn error (1011) [ 1168.220969] connection4:0: ping timeout of 15 secs expired, recv timeout 10, last rx 84060, last ping 85060, now 86560 [ 1168.220973] connection4:0: detected conn error (1011) [ 1168.220975] connection3:0: ping timeout of 15 secs expired, recv timeout 10, last rx 84060, last ping 85060, now 86560 [ 1168.220978] connection3:0: detected conn error (1011) [ 1168.220985] connection6:0: detected conn error (1011) [ 1168.480994] sd 14:0:0:0: [sde] Unhandled error code [ 1168.480998] sd 14:0:0:0: [sde] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1168.481001] sd 14:0:0:0: [sde] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1168.481009] end_request: I/O error, dev sde, sector 0 [ 1168.481015] Buffer I/O error on device sde, logical block 0 [ 1168.481076] sd 11:0:0:0: [sdc] Unhandled error code [ 1168.481078] sd 11:0:0:0: [sdc] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1168.481080] sd 11:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1168.481087] end_request: I/O error, dev sdc, sector 0 [ 1168.481092] Buffer I/O error on device sdc, logical block 0 [ 1168.481144] sd 10:0:0:0: [sdd] Unhandled error code [ 1168.481147] sd 10:0:0:0: [sdd] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1168.481150] sd 10:0:0:0: [sdd] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1168.481156] end_request: I/O error, dev sdd, sector 0 [ 1168.481163] Buffer I/O error on device sdd, logical block 0 [ 1168.481168] sd 13:0:0:0: [sdj] Unhandled error code [ 1168.481170] sd 13:0:0:0: [sdj] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1168.481172] sd 13:0:0:0: [sdj] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1168.481178] end_request: I/O error, dev sdj, sector 0 [ 1168.481184] Buffer I/O error on device sdj, logical block 0 [ 1457.105996] device-mapper: multipath round-robin: version 1.0.0 loaded [ 1457.106155] device-mapper: multipath: Cannot access device path 8:0: -16 [ 1457.106164] device-mapper: table: 252:1: multipath: error getting device [ 1457.106172] device-mapper: ioctl: error adding target to table [ 1457.171292] device-mapper: multipath: Cannot access device path 8:0: -16 [ 1457.171299] device-mapper: table: 252:1: multipath: error getting device [ 1457.171304] device-mapper: ioctl: error adding target to table [root@xen3 ~]# fdisk -l Disk /dev/sda: 299.4 GB, 299439751168 bytes 255 heads, 63 sectors/track, 36404 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 5 40131 de Dell Utility /dev/sda2 * 6 528 4194304 83 Linux Partition 2 does not end on cylinder boundary. /dev/sda3 528 1050 4194304 83 Linux /dev/sda4 1050 36404 283986359+ 8e Linux LVM Disk /dev/sdb: 2040 MB, 2040528896 bytes 255 heads, 63 sectors/track, 248 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 1 248 1992028+ 83 Linux Disk /dev/dm-1: 2040 MB, 2040528896 bytes 255 heads, 63 sectors/track, 248 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/dm-1p1 1 248 1992028+ 83 Linux [root@xen3 ~]# xe sr-probe type=lvmoiscsi device-config:target=192.168.130.101 device-config:targetIQN=iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 Error code: SR_BACKEND_FAILURE_107 Error parameters: , The SCSIid parameter is missing or incorrect, <?xml version="1.0" ?> <iscsi-target/> Note: the xml ends there correctly on the last line - it doesn't ever return a list of LUNs (and there is one in the group on the SAN for those servers.

    Read the article

  • Dual booting on separate hard drives

    - by tornadorider
    I have windows XP professional installed on 1 hard drive and Ubuntu 10.10 on my second hard drive. On start up the computer completely skips the grub menu and boots straight into 10.10. I have tried running os-prober with the windows hard drive mounted and then updating grub but it didnt work. Any ideas? I have changed the boot order so that the HDD with xp on it is first however the computer still booted into linux. I tried running grub-install /dev/sda and got this /usr/sbin/grub-setup: warn: Sector 32 is already in use by FlexNet; avoiding it. This software may cause boot or other problems in future. Please ask its authors not to store data in the boot track.. /usr/sbin/grub-setup: warn: Sector 33 is already in use by FlexNet; avoiding it. This software may cause boot or other problems in future. Please ask its authors not to store data in the boot track.. Installation finished. No error reported I checked using disk utility and the code for my xp hard drive is sdb so i ran the camand grub-install /dev/sdb shich gave me this Installation finished. No error reported. So i rebooted but it still didnt work. Any other ideas? Additional info gedit /boot/grub/grub.cfg: # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga } insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 load_video insmod gfxterm fi terminal_output gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c set locale_dir=($root)/boot/grub/locale set lang=en insmod gettext if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.35-28-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux /boot/vmlinuz-2.6.35-28-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro quiet splash initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-28-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c echo 'Loading Linux 2.6.35-28-generic ...' linux /boot/vmlinuz-2.6.35-28-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-22-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux /boot/vmlinuz-2.6.35-22-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro quiet splash initrd /boot/initrd.img-2.6.35-22-generic } menuentry 'Ubuntu, with Linux 2.6.35-22-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c echo 'Loading Linux 2.6.35-22-generic ...' linux /boot/vmlinuz-2.6.35-22-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-22-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### if [ "x${timeout}" != "x-1" ]; then if keystatus; then if keystatus --shift; then set timeout=-1 else set timeout=0 fi else if sleep --interruptible 3 ; then set timeout=0 fi fi fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### sudo fdisk -l: Disk /dev/sda: 80.1 GB, 80060424192 bytes 255 heads, 63 sectors/track, 9733 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0008a483 Device Boot Start End Blocks Id System /dev/sda1 * 1 9352 75112448 83 Linux /dev/sda2 9352 9734 3068929 5 Extended /dev/sda5 9352 9734 3068928 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc5d6c5d6 Device Boot Start End Blocks Id System /dev/sdb1 1 60800 488375968+ 7 HPFS/NTFS sudo blkid /dev/sda1: UUID="d682c9bd-dd89-4827-9802-a1f921ebe21c" TYPE="ext4" /dev/sda5: UUID="09e9c2cb-d903-4f0b-a181-536951845231" TYPE="swap" /dev/sdb1: UUID="B21844EB1844AFE1" TYPE="ntfs" sudo os-prober (nothing) Boot Info Script 0.55 dated February 15th, 2010 ============================= Boot Info Summary: ============================== => Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in partition #1 for (,msdos1)/boot/grub. => Grub 2 is installed in the MBR of /dev/sdb and looks on the same drive in partition #1 for (,msdos1)/boot/grub. sda1: _________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 10.10 Boot files/dirs: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sda2: _________________________________________________________________________ File system: Extended Partition Boot sector type: Unknown Boot sector info: sda5: _________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: sdb1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows XP Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows XP Boot files/dirs: =========================== Drive/Partition Info: ============================= Drive: sda ___________________ _____________________________________________________ Disk /dev/sda: 80.1 GB, 80060424192 bytes 255 heads, 63 sectors/track, 9733 cylinders, total 156368016 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/sda1 * 2,048 150,226,943 150,224,896 83 Linux /dev/sda2 150,228,990 156,366,847 6,137,858 5 Extended /dev/sda5 150,228,992 156,366,847 6,137,856 82 Linux swap / Solaris Drive: sdb ___________________ _____________________________________________________ Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/sdb1 * 63 976,751,999 976,751,937 7 HPFS/NTFS blkid -c /dev/null: ____________________________________________________________ Device UUID TYPE LABEL /dev/sda1 d682c9bd-dd89-4827-9802-a1f921ebe21c ext4 /dev/sda2: PTTYPE="dos" /dev/sda5 09e9c2cb-d903-4f0b-a181-536951845231 swap /dev/sda: PTTYPE="dos" /dev/sdb1 B21844EB1844AFE1 ntfs /dev/sdb: PTTYPE="dos" ============================ "mount | grep ^/dev output: =========================== Device Mount_Point Type Options /dev/sda1 / ext4 (rw,errors=remount-ro,commit=0) =========================== sda1/boot/grub/grub.cfg: =========================== # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga } insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 load_video insmod gfxterm fi terminal_output gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c set locale_dir=($root)/boot/grub/locale set lang=en insmod gettext if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.35-28-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux /boot/vmlinuz-2.6.35-28-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro quiet splash initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-28-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c echo 'Loading Linux 2.6.35-28-generic ...' linux /boot/vmlinuz-2.6.35-28-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-22-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux /boot/vmlinuz-2.6.35-22-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro quiet splash initrd /boot/initrd.img-2.6.35-22-generic } menuentry 'Ubuntu, with Linux 2.6.35-22-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c echo 'Loading Linux 2.6.35-22-generic ...' linux /boot/vmlinuz-2.6.35-22-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-22-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### if [ "x${timeout}" != "x-1" ]; then if keystatus; then if keystatus --shift; then set timeout=-1 else set timeout=0 fi else if sleep --interruptible 3 ; then set timeout=0 fi fi fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. menuentry "Windows XP" { set root=(hd1,1) chainloader (hd1,1)+1 } ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### =============================== sda1/etc/fstab: =============================== # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 /dev/sda1 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=09e9c2cb-d903-4f0b-a181-536951845231 none swap sw 0 0 =================== sda1: Location of files loaded by Grub: =================== 51.7GB: boot/grub/core.img 58.5GB: boot/grub/grub.cfg 1.2GB: boot/initrd.img-2.6.35-22-generic 1.3GB: boot/initrd.img-2.6.35-28-generic 58.2GB: boot/vmlinuz-2.6.35-22-generic 51.7GB: boot/vmlinuz-2.6.35-28-generic 1.3GB: initrd.img 1.2GB: initrd.img.old 51.7GB: vmlinuz 58.2GB: vmlinuz.old =========================== Unknown MBRs/Boot Sectors/etc ======================= Unknown BootLoader on sda2 00000000 d9 ed 13 ab ff a8 33 8c 01 b2 47 99 e1 4a b1 f1 |......3...G..J..| 00000010 69 5f a7 29 a4 1a 03 9e 31 b9 45 02 71 e6 58 78 |i_.)....1.E.q.Xx| 00000020 3d f6 ee 7b 3e 33 1b 82 c6 7d cf 1a c8 e7 bc 2f |=..{>3...}...../| 00000030 b9 e1 70 75 cf 18 aa e7 d5 7e 3c f1 b4 e7 9e 3a |..pu.....~<....:| 00000040 55 38 f1 b4 ee 78 59 0b 5e f7 3c 4c 57 73 9c 2a |U8...xY.^.<LWs.*| 00000050 28 f1 19 ed 11 9c b2 19 e2 80 92 1c 7b 84 ee 0b |(...........{...| 00000060 e2 c0 ac af 0a 50 42 b9 cf 0c dc 2c 20 77 85 dc |.....PB...., w..| 00000070 8f 70 5f 7b 84 9b a1 f7 8c 2d ee 70 5c ae f7 39 |.p_{.....-.p\..9| 00000080 63 f7 09 8a ec 79 4c ed 9f cc ad 3c f8 1b 47 7d |c....yL....<..G}| 00000090 3f 97 d5 16 cb 29 45 38 25 61 36 08 de 10 93 0f |?....)E8%a6.....| 000000a0 95 4f ea 54 f9 89 ff f1 bf 9a cc bb fd b6 22 b1 |.O.T..........".| 000000b0 65 08 05 21 78 19 46 b0 24 7e fb de d4 b3 ba d6 |e..!x.F.$~......| 000000c0 ec 11 65 82 ee 10 1d 12 04 91 da 6d 67 47 ea 9b |..e........mgG..| 000000d0 6f b0 aa fb cb 67 10 64 86 e8 26 85 fb f9 50 77 |o....g.d..&...Pw| 000000e0 9d 13 9b 9e d9 11 f3 a1 50 1b 11 b7 93 79 9f ab |........P....y..| 000000f0 c1 b6 86 0f 35 ed d4 9f dc f8 db bd ed 45 3a 68 |....5........E:h| 00000100 54 68 4a 1d d1 fc b8 c9 72 b4 d7 7b 60 e7 39 2f |ThJ.....r..{`.9/| 00000110 2a 0a 4e 52 72 52 c6 e2 2a 55 6a 2a e1 82 40 71 |*.NRrR..*Uj*..@q| 00000120 11 11 e0 53 d6 ff 1b a9 c6 65 df 1e b7 15 6f a2 |...S.....e....o.| 00000130 15 02 a4 6d 19 b7 78 57 a6 ee 9e 36 08 7d 6f 7c |...m..xW...6.}o|| 00000140 fd f7 7c d5 40 ff 0f c7 97 dc aa 00 ce 8b bb dc |..|.@...........| 00000150 e2 eb 1c 50 74 d8 14 cc 9a d6 5c a2 ab f2 67 f9 |...Pt.....\...g.| 00000160 58 ed 43 79 0e 78 7a 5c a6 f8 7b e8 05 4e 62 8a |X.Cy.xz\..{..Nb.| 00000170 0a 5f 22 ee a6 38 b9 e1 32 45 97 08 cc 75 66 c6 |._"..8..2E...uf.| 00000180 b3 a2 2d 89 a1 e9 95 21 28 53 fd dd be b1 b2 a2 |..-....!(S......| 00000190 78 3f a3 c9 3d e3 31 54 88 cf 78 0d e1 21 a8 74 |x?..=.1T..x..!.t| 000001a0 06 60 9d 21 c6 7a 24 e1 cc 28 f8 98 e0 99 e3 fc |.`.!.z$..(......| 000001b0 fa 8b eb d5 56 03 20 b8 54 ba c6 ee 9f 57 00 fe |....V. .T....W..| 000001c0 ff ff 82 fe ff ff 02 00 00 00 00 a8 5d 00 00 00 |............]...| 000001d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 000001f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.| 00000200

    Read the article

  • "0x80004005: Unspecified error" when renaming folders in Windows 7

    - by Michael Steele
    Setup I've just installed Windows 7 Ultimate 64bit. The operating system is installed on an 80GB Intel X-25M. I have a secondary 500GB Barracuda 7200.12 to be used for storage. This second drive is mounted as 'G'. Problem I'm getting an error whenever I try to rename a folder within this drive. The error says: An unexpected error is keeping you from renaming the folder. If you continue to receive this error, you can use the error code to search for help with this problem. Error 0x80004005: Unspecified error Clicking the "Try Again" button gets past the error, and correctly renames the folder. If I create a folder and leave it's name as "New Folder", then I don't see an error. I'm also able to manipulate files however I want without seeing an error. Things I've Tried Changing permissions on the drive Reformatting the drive. I've tried using both a "Basic" and "Dynamic" partition table. Checking the drive for errors using Microsoft tools Things I've Not Yet Tried When I first installed Windows I was given a choice between three types of partitions to use. I no longer remember what the choices were or what I selected. One was a GUID partition table, one was a traditional MBR, and I can't remember the third option.

    Read the article

  • SYSPART hidden folder in Windows 7

    - by BenGC
    We had a user with a Lenovo G-series laptop getting a STOP error on boot. We reinstalled Windows 7 Home Premium using non-OEM media and restored the user's files from backup. We are now seeing a hidden folder in the root of the C:\ drive called SYSPART which appears to contain a copy of the contents of the C:\ drive - so while the user has 160 GB of files, the drive is using 320 GB because of this folder. What is it, and is it safe to delete?

    Read the article

  • 3Ware 9650SE RAID-6, two degraded drives, one ECC, rebuild stuck

    - by cswingle
    This morning I came in the office to discover that two of the drives on a RAID-6, 3ware 9650SE controller were marked as degraded and it was rebuilding the array. After getting to about 4%, it got ECC errors on a third drive (this may have happened when I attempted to access the filesystem on this RAID and got I/O errors from the controller). Now I'm in this state: > /c2/u1 show Unit UnitType Status %RCmpl %V/I/M Port Stripe Size(GB) ------------------------------------------------------------------------ u1 RAID-6 REBUILDING 4%(A) - - 64K 7450.5 u1-0 DISK OK - - p5 - 931.312 u1-1 DISK OK - - p2 - 931.312 u1-2 DISK OK - - p1 - 931.312 u1-3 DISK OK - - p4 - 931.312 u1-4 DISK OK - - p11 - 931.312 u1-5 DISK DEGRADED - - p6 - 931.312 u1-6 DISK OK - - p7 - 931.312 u1-7 DISK DEGRADED - - p3 - 931.312 u1-8 DISK WARNING - - p9 - 931.312 u1-9 DISK OK - - p10 - 931.312 u1/v0 Volume - - - - - 7450.5 Examining the SMART data on the three drives in question, the two that are DEGRADED are in good shape (PASSED without any Current_Pending_Sector or Offline_Uncorrectable errors), but the drive listed as WARNING has 24 uncorrectable sectors. And, the "rebuild" has been stuck at 4% for ten hours now. So: How do I get it to start actually rebuilding? This particular controller doesn't appear to support /c2/u1 resume rebuild, and the only rebuild command that appears to be an option is one that wants to know what disk to add (/c2/u1 start rebuild disk=<p:-p...> [ignoreECC] according to the help). I have two hot spares in the server, and I'm happy to engage them, but I don't understand what it would do with that information in the current state it's in. Can I pull out the drive that is demonstrably failing (the WARNING drive), when I have two DEGRADED drives in a RAID-6? It seems to me that the best scenario would be for me to pull the WARNING drive and tell it to use one of my hot spares in the rebuild. But won't I kill the thing by pulling a "good" drive in a RAID-6 with two DEGRADED drives? Finally, I've seen reference in other posts to a bad bug in this controller that causes good drives to be marked as bad and that upgrading the firmware may help. Is flashing the firmware a risky operation given the situation? Is it likely to help or hurt wrt the rebuilding-but-stuck-at-4% RAID? Am I experiencing this bug in action? Advice outside the spiritual would be much appreciated. Thanks.

    Read the article

  • RAID 5 RECONSTRUCT with RAID Reconstructor

    - by user22914
    I have Dell Poweredge server 2600 with Raid 5 in 3 hard drive Scsi 36gb each, it was fail to boot sinc the third drive is offline. I attached Sata card adapter to Sata hard drive and install OS SERVER 2003 to it, downloaded drivers for Raid and everything goes fine when I use recovery data software called "GetDataBack" from here http://www.runtime.org/data-recovery-software.htm but the problem that not all data recovered, I am still looking for importants data with about 5 GB size. I have another software called "RAID Reconstructor" from "http://www.runtime.org/raid.htm" I thought if I run it to reconstruct that will help to recover more data and put the third drive to be Online but I am afraid that might erase the current data in the other drives. Please I need your advise in how I could retrive the remaining data? Thanks

    Read the article

  • Windows server 2008 R2 + VMWare Workstation 7.0

    - by G0RY
    Hi, im trying to install Windows 2008 R2 on VMWare, and I got this error: A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD or usb flash drive, please insert it now. I was trying to install it from ISO, daemon and from DVD drive, but always get this error.

    Read the article

  • CHKDSK: What option DOES NOT delete files and turn them into .chk files?

    - by CHKDSKuser
    I had a recent power outage while using my computer, with a 1TB hard drive being directly accessed as the power went out. When the power came back on, and I rebooted my computer, one of my 1TB hard drives would not register with WinXP SP3, and showed a Total Space of 0, and an Available Space of 0. The file system (NTFS) also did not register...every entry for the drive was either blank or zeroed. My assumption is that the file tables were damaged/corrupted because the drive was being directly accessed when the power went out. After doing some research, I ran CHKDSK with whatever default options it runs with (I'm not sure what they are as I didn't see them displayed). Upon completion of CHKDSK, the drive registered with WinXP as a 1TB hard drive, with an accurately-reflected amount of available space. But CHKDSK also deleted about 16GB of files from their original directories, and changed them all into sequentially-named *.chk files. My question is how can CHKDSK be run in a situation like mine where the file tables needed to be restored, but without having CHKDSK delete any files from their original directories, even if they may be damaged/corrupt? I'd simply like to be able to run CHKDSK and have it restore the file tables, and repair bad sector damage, as it did, but not have it do anything else such as delete files and convert them to CHK files. Any ideas? Or is there a CHKDSK alternative that can perform the same functions without the file deletions?

    Read the article

< Previous Page | 167 168 169 170 171 172 173 174 175 176 177 178  | Next Page >