Search Results

Search found 19267 results on 771 pages for 'computer adventure games'.

Page 172/771 | < Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179  | Next Page >

• Laptop shuts down randomly without warning

  - by Robert P.

  My Asus Zenbook UX32V turns off randomly when I'm working on it. This happens both when the computer is recently turned on (5 minutes), and after being on for several days. I'm not running any heavy software The laptop is not heating The fan is not working on the maximum capacity (it's not heating) It happens when the laptop is lying still on the table It is no warning, it simply goes black It happens both when charging and on battery My guess is that it suddenly lose power somehow. What puzzles me is that I can flip the laptop upside down, sideways, shake it, etc. without it shutting off. This makes me think it's not something that's loose causing occasional short-circuits. I realize that the laptop probably doesn't like flipping and shaking, but it was the best way I could troubleshoot. I rarely turn the computer off, only have it in hibernate or sleep mode (most often hibernate). I've never experienced that the laptop is off when I wake it up from sleep mode. I've had the problem for a few months and it happens 2-8 times a week. Specs: Asus Zenbook UX32V Windows 8.1 (it happened in Windows 8.0 too) Intel i5-3317U CPU @ 1.70GHz The laptop is approx 1.5 years, but it has a small dent on one of the sides that probably voids the warranty. The dent has been there since week one and I don't think it's related to the problems I'm having now. Does anyone have a clue what might cause this, and how it might be fixed? I've read all other questions (some of which are listed below) that seem related to my issue, but none report the same behavior as I'm experiencing. Most report heavy games, heating etc. Asus N53J Laptop randomly shuts down Laptop is randomly shutting off Computer shuts down without warning My laptop acer aspire 5720 suddenly turn off randomly Computer randomly shutting down Windows 8.1 randomly shuts self down ASUS K55VM Laptop unexpectedly shuts down

  Read the article

• Laptop Randomly Turning On and Off

  - by Ian Mallett

  So, I have a pretty new laptop, and one of its quirks is that, at random times (though typically in the middle of the night), it seems to wake up from sleep mode, churn a bit, and then go back into sleep mode. I write "seems" because its fans are very loud, so it's obvious when it's not asleep, but during the time it is "on", I can't see anything on the screen. I have researched the problem somewhat, and could only find similar issues; nothing identical. In those cases, it appeared that certain devices could be responsible. Nothing is plugged into my computer during this behavior, but I nonetheless disabled every device's permission to wake the computer through the device manager. This included disabling the magic packet wake for the network (despite its only having a wireless connection). Using "powercfg /lastwake" gives an empty wake history. But, I also went through all the tasks and checked if they would wake the computer. None appeared to. The problem persisted, so, after some more research, I found this, and executed it for all power schemes on the computer. The problem persists. System: OS: Windows 7 Professional CPU: Intel 990X GPU: NVIDIA GeForce 580M/12GB RAM Motherboard: Clevo X7200 Model: NP7282-S1 (Sager-built laptop)

  Read the article

• Samsung S23A750D 23" 120Hz get no signal

  - by John Carter

  I have a few days ago received this monitor. Samsung S23A750D 23" 120Hz I am using it with a Gainward Nvidia GTX570 Phantom GPU via DisplayPort cabling. The trouble I am having is that the monitor has great trouble picking up a signal from the GPU when the computer has gone into sleep mode or been switched off (at this point I can get a signal to the monitor). It's only when I turn the computer back on and then the monitor that I get no signal. To get a signal I have to remove the power cable and put back in or sometimes remove the DP cable and put back in. I have tried not turning the monitor off (the monitor goes into a sleep mode when the computer goes into sleep mode) but on putting the computer on it does not pick up a signal. It is only by removing the power cable and/or DisplayPort cable will I get a signal. And this is intermittent. I have tried upgrading the firmware from Samsung but this hasn't helped. Any ideas?

  Read the article

• Blank list of windows services

  - by Joe

  Recently when I open windows services (always as administrator) I get a blank list of services: When I try and click on one of the empty lines I get this "Script Error" message: This happens over and over again, after several times I restarted my computer. I can't pinpoint exactly when this started happening or if I made any specific changes to my computer at that time. Someone told my to try running scf /scannow as administrator, but when I try to do that the scan stops at 34% and I get the message: "Windows Resource Protection could not perform the requested operation." I am running Windows 7 Enterprise 64 bit, and I would really like to avoid reinstalling windows. Does anyone know how to fix this? Edit - Here is another attempt I made and some more information that might help: Following WhoIsRich's suggestion, I tried the command sfc /scannow /offbootdir=c:\ /offwindir=c:\windows. This gave the error message "The arguments passed to sfc are invalid. The offline windows directory specified points to the online system", and then I realized this command is meant to be run after booting from another system. Since I don't have my windows installation disk right now, I used my own system to create a recovery disk, and then restarted my computer and used the recovery disk to boot. I then ran the above command, and I got the following message: "Windows Resource Protection found corrupt files but was unable to fix some of them. Details are included in the CBS.log". I then restarted my computer and let it boot up normally. The problem with windows services persists, and the CBS.log file is a long log file with many entries, and I don't know if there is useful information in it, and if there is, how to find it.

  Read the article

• How to tell if OpenGL is really working in Ubuntu 10.04

  - by Jonathan

  I have a lenovo S9e running Intel integrated graphics. Here is my lspci output related to the graphics: 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) Subsystem: Lenovo Device 3870 Flags: bus master, fast devsel, latency 0 Memory at f0580000 (32-bit, non-prefetchable) [size=512K] Capabilities: [d0] Power Management version 2 I want to know how I can make sure OpenGL support is running in full on an Ubuntu 10.04 installation. I have a few hints to think that it is not: The "Desktop Effects" will not load Apps such as stardock, when attempting to use OpenGL rendering, will display black boxes instead of transparency In the games Pioneers, the number-tile icons are suspiciously just black circles Windows games running with Wine will only support software rendering, not hardware rendering When I boot into a Knoppix LiveCD, the desktop effects do work, splendidly, meaning compiz detects my computer as capable. My problem with troubleshooting is that Canonical has basically eliminated the conf-file-based mechanism of X11 as far as I can tell, thus making it even harder to ensure graphics modules are loading properly. How do I debug and test OpenGL on m Ubuntu 10.04 installation?

  Read the article

• Why can't I connect to my router's config page with Windows 7?

  - by user17940

  I've got a Belkin wireless router, and just bought a new Dell computer with Windows 7 pre-installed. I can connect to the Internet and my home network just fine, but when I try to visit my router's configuration page at http://192.168.2.1, I get a "Connection was reset" error. Nothing I do will make the router's configuration page come up in my web browser. More background information: I could always get to the router's config page from my Windows XP machine. I never had any trouble prior to getting this Windows 7 computer. I can ping 192.168.2.1 successfully from my Windows 7 computer. My PC is connected to the router by a physical CAT5 cable, not via wireless. Every device connected to my router, including the new computer, can get to the Internet with no problem. Here are some things that did not solve the problem: I tried turning off IPV6 in Windows. I tried turning off my firewall and antivirus software I tried using https instead of http I tried disabling and then enabling the network connection in Windows I tried reverting my network card driver back to an older version I have tried both Firefox and Internet Explorer web browsers. Has anyone experienced something like this before, and solved it? Thanks a lot for your help!

  Read the article

• AC/battery laptop issues(not a simple charging fix)

  - by Deric Hatchett

  Is it possible to run a laptop off the battery while the AC is plugged in? I can play games no problem while just the battery is plugged in, but obviously that means I have to let it charge after every hour or so. But, when I plug it in to charge, it can't handle any video games anymore. I thought it was the brick in the power cord going out, but I just bought a new one and it still doesn't work. The specs are actually better than the old cord. I think the problem is an over heating problem in the AC outlet, but if it charges the battery while I play, it would work just fine running solely off the battery.

  Read the article

• Enable multiple audio output on Windows 7

  - by patrick

  For Windows 7, 64 bit: I have a digital SPDIF output to my stereo, which controls speakers in other rooms. I also have a set of speakers connected to the regular audio jack at the computer. This allows me to send music to the kitchen while my child plays games on the computer. Works great. Except when I'm playing games and still want to listen to music. ;-D I know I can manually switch WMP to play through the speakers instead of SPDIF, but I was wondering if there's any way to enable simultaneous audio out in Windows 7? Virtual Audio Card is a non-starter because I'm running 64 bits and the VAC driver isn't signed.

  Read the article

• VPN sharing on Mac OS X 10.5 machine

  - by Jens

  I have a rather weird problem. I want to share a VPN connection that has been established by my Mac OS X 10.5 computer with another machine in my network. This is what I did: In the /etc/hostcongig file on the main computer I added the line: IPFORWARDING=-YES- I assigned a fixed IP address to my computer (192.168.178.30), a fixed one to the other machine (192.168.178.60) and my computer's IP address as gateway on the other machine. I connected to my VPN using the internal Mac OS X VPN client (PPTP connection) I run this script: #!/bin/sh natd -same_ports -use_sockets -unregistered_only -dynamic -interface ppp0 -clamp_mss ipfw -f flush ipfw add divert natd ip from any to any via ppp0 ipfw add pass all from any to any sysctl -w net.inet.ip.forwarding=1 Source: Using (and sharing) a VPN connection on your Mac Now everthing works smootly, however speed is an issue. I get 1,8 MBit/s on my main machine and only 0,3 - 0,6 MBit/s on the other one. My question: What could possibly be wrong? Do I have to tweak MTU settings, is there any packet inspection ongoing that needs time....? Any help appreciated!

  Read the article

• How to fix audio/game stuttering in Google Chrome's Flash plug-in?

  - by Simon Belmont

  I'm having an issue. Windows XP, running the latest Chrome 23 build. I'm using Flash 11.5 built into Chrome (Pepper Flash). It runs horribly. Chrome 22 did not have this issue as far as I recall. What a shame. YouTube videos stutter badly and after a while, they begin to lag and lose sync with the video. I disabled Pepper Flash and tested HTML5 video in YouTube and it was smooth as glass. Additionally, certain Flash based games are almost unusable now. The plug-in is using 100% CPU and it lags horribly in these games. Google/Adobe, please fix this. I shouldn't have to disable the built-in Flash plug-in (with added sandboxing security) and use regular Flash to resolve this. Short of waiting for an update to Chrome, does anyone have a better solution to fixing this? I am all ears.

  Read the article

• Serious voltage and temperature problems

  - by James Willson

  My computer has been acting up when I play games so I wanted to look into why. Issue 1: GPU Temp According to afterburner and speedfan my 8800GTX idles at 90 degrees and then when playing games shoots up to over 110C which is when my graphics basically starts to give rendering issues. Issue 2: CPU Temp Speedfan is saying my CPU temp is 83C idle but when I look at core temp it says core0 is at 35C and core1 is at 33C. Issue 3: Voltages This is what speedfan is saying for my voltages: Vcore1: 1.01V Vcore2: 1.90V +3.3V: 3.31V +5V: 4.95V +12V: 0.51V -12V: -16.80V -5V: -8.43V +5V 5.13V Vbat: 3.25V Vcore: 3.00V +3.3V: 3.20V These voltages, for lack of a better word, look f*cked. With all this happening, the computer runs ok under normal use. Is the software giving out incorrect readouts or instead should I immediately move the computer into another room before it explodes? P.s I would like to add this is a stock system. EVGA 8800GTX, E6850 CPU, 800W PSU

  Read the article

• Proper end of day sequence to maintain monitor config

  - by WarmBeer

  I've got an HP EliteBook 6930p that travels from home, where it is connected to individual cables, and work where there is a docking station. At both locations I have an external monitor as the secondary monitor and like to have the laptop screen as the primary, i.e. with the task bar. At the end of the day I close the laptop, which is supposed to set it to standby. When I get home I plug in the power cord and the external monitor cord and open the computer. When heading into work I close the computer and unplug everything. Inevitably when I open the computer at the new location the monitors are reversed, i.e. the primary, task bar display is on the external monitor and the laptop shows the secondary, even though when i click identify the laptop has the 1. I then have to disable the secondary display, switch the primary to the laptop and re-enable the secondary. I've tried locking the computer before closing and occasionally that works to keep the setup in place but not always. Any suggestions for how to keep the config in place during transport? ed

  Read the article

• How to configure a large mtu (linux)

  - by Somejan

  I have a gigabit ethernet connection from my laptop to my router, and a working ipv6 connection to the internet. I can receive very large packets from sites on the internet, with sizes up to at least 10000 bytes (according to wireshark). (edit: turns out to be linux's 'generic receive offload') However, when trying to send anything, my local computer fragments at just below 1500 bytes for ipv6. (On ipv4, I can send tcp packets to the internet of at least 1514 bytes, I can ping with packets up to the configured mtu of 6128 but they are blackholed.) I'm on ubuntu 12.04. I have configured an mtu for my eth0 of 6128 (the maximum it accepts), both using ip link set dev eth0 mtu 6128 and in the NetworkManager applet gui, and restarted the connection. ip link show eth0 shows the 6128 mtu is indeed set. ip -6 route shows that none of the paths the kernel knows about have an mtu set. I can ping over ipv4 with packets up to 6128 bytes (though I don't get responses), but when I do ping6 myrouter -c3 -s1500 -Mdo I get error replies from my own computer saying that the packets are too large and the mtu is 1480. I have confirmed with Wireshark that nothing is put on the wire, and the replies are indeed generated by my own computer. So, how do I get my computer to use the larger mtu?

  Read the article

• How can I remove all drivers and other files related to a USB Mass Storage device?

  - by Bob

  I have a flash drive here that does not work on one OS on computer - let's call it the desktop Windows 7. It works fine on another computer - laptop Windows 7. It also works fine on Windows 8 on the same desktop computer. Other flash drives work fine under desktop Windows 7. So not a hardware issue, not a generic USB Mass Storage driver issue. It's something specific to this drive. On desktop Windows 7, I can connect the drive but no volume comes up under Windows Explorer. Ditto for Disk Management. With diskpart, loading hangs until I unplug the drive, if I replug it and try list disk it hangs again. If I unplug the drive at this point, list disk prints out all attached drives - including the just removed flash drive. The drive consistently appears under Device Manager, but uninstalling the drivers, restarting and reinstalling the drivers (by inserting the drive) only works for the first insertion. After that it fails again. I get the feeling that the driver files are not actually removed, and are corrupted, meaning every reinstall it's the same corrupted drivers being installed. Is there any way to remove these drivers completely? Or perhaps some other setting Windows 7 retains? Formatting the drive through another computer/OS does not help. I've also tried a complete wipe and rebuild of the MBR and single partition. The allocation unit size makes no difference; neither does a NTFS format. This is a relatively small matter, and I would not like to reinstall the entire OS!

  Read the article

• How can I use my cell phone to establish a dial-up networking connection?

  - by gWiz

  I am using Windows 7 and have a BlackBerry with T-Mobile (U.S.). I have paired the phone with my computer over Bluetooth, which automatically creates a serial port for it. I am able to open the port in PuTTY and successfully issue AT commands to the modem, including dialing. However, while using Windows to create and establish a Dial-Up Networking connection, I get an error dialog stating "Error 678. The remote computer did not respond." In my testing, I also tried setting up a connection to dial a number connected to a phone. When attempting to connect over this connection, the phone does ring but the very moment I answer the call, my computer displays the above error dialog. What must be done to successfully establish such a PPP connection? Some special AT initialization string perhaps? To clarify, I'm not referring to the well-described and popular technique known as "tethering," in which the remote host of the data link is the mobile service provider. I am interested specifically in establishing direct data links with remote hosts other than my mobile service provider. Think old-school landline connection to your friend's computer or BBS. Edit 1 As grawity pointed out in comments, the missing piece of the puzzle is the actual modulator that is compatible with v-series protocols, which I expected to be built into the cellphone. So far the best only software alternative I could find is this experimental project. Edit 2 Found this forum discussion today. The participants state that there is no old-school modem in the BlackBerry. Edit 3 When I place a call in PuTTY with ATD, immediately after the call is answered (and the callee is initiating the handshake) the cellphone returns OK. This is not the expected behavior for establishing a data connection. The phone should reciprocate the handshake, and upon success return CONNECT. (Alternatively it should return BUSY or NO CARRIER, but never simply OK.) Windows DUN must be interpreting this as the "Error 678" I was seeing.

  Read the article

• script to list user's mapped drive not giving results or error

  - by user223631

  We are in the process of migrating two file servers to a new server. We have mapped drives via user group in group policy. Many users have manually mapped drives and we need to find these mappings. I have created a PowerShell script to run that remotely get the drive mappings. It works on most computers but there are many that are not returning results and I am not getting any error messages. Each workstation on the list creates a text file and the ones that are not returning results have no text in the files. I can ping these machines. If the machine is not turned on, it does come up error message that the RPC server is not available. My domain user account is in a group that is in the local admin account. I have no idea why some are not working. Here is the script. # Load list into variable, which will become an array of strings If( !(Test-Path C:\Scripts)) { New-Item C:\Scripts -ItemType directory } If( !(Test-Path C:\Scripts\Computers)) { New-Item C:\Scripts\Computers -ItemType directory } If( !(Test-Path C:\Scripts\Workstations.txt)) { "No Workstations found. Please enter a list of Workstations under Workstation.txt"; Return} If( !(Test-Path C:\Scripts\KnownMaps.txt)) { "No Mapping to check against. Please enter a list of Known Mappings under KnownMaps.txt"; Return} $computerlist = Get-Content C:\Scripts\Workstations.txt # Loop through each item in the array (each computer in the list of computers we loaded into the variable) ForEach ($computer in $computerlist) { $diskObject = Get-WmiObject Win32_MappedLogicalDisk -computerName $computer | Select Name,ProviderName | Out-File C:\Tester\Computers\$computer.txt -width 200 } Select-String -Path C:\Tester\Computers\*.txt -Pattern cmsfiles | Out-File C:\Tester\Drivemaps-all.txt $strings = Get-Content C:\Tester\KnownMaps.txt Select-String -Path C:\Tester\Drivemaps-all.txt -Pattern $strings -notmatch -simplematch | Out-File C:\Tester\Drivemaps-nonmatch.txt -Width 200 Select-String -Path C:\Tester\Drivemaps-all.txt -Pattern $strings -simplematch | Out-File C:\Tester\Drivemaps-match.txt -Width 200

  Read the article

• Keyboard layout to shift wasd keys

  - by Joel Coehoorn

  I like to play video games on my computer. One of the things that bugs me, though, is how the wasd keys became the standard movement keys in first person shooters and mmorpgs. To me, esdf makes a lot more sense, because that matches your normal hand placement for typing. "Fixing" that layout is always the first thing I do when installing a new game. Sadly, this is often a pain in the neck, and some games won't let you do it at all. Is there an alternative keyboard layout you can install that will just switch these around, so the wasd keys fall in the esdf positions? And is low-level enough two work with DirectX/DirectInput, perhaps that works with the language bar for easy swapping back and forth?

  Read the article

• Building a Server at Home

  - by madhairsilence

  Am left with a Spare PC . So , I thought of converting it to a Server kind of thing. I read about NAS Serer for simple file storage. But it is just a file server. I also play games like counter strike and other online games. So, I would like to use the same server for those purpose., so that a game server will running all the time so that me and my friends can join any time. Is running NAS server a best option or, is there any better arrangement possible so that my spare system can act better than a simple file server

  Read the article

• I just got a virus 6 mins ago, how? Situation.

  - by acidzombie24

  -Edit- for the people who say it isn't a virus. Norton does detect it as a virus, an icon was placed on my system tray and rkpg.exe is in my C: which was placed 6 min ago around the time my computer rebooted on its own causing me to lose data :@. Situation I on Windows XP, behind a Linksys router, I don't have DMZ on so nothing should be connecting to me. I had Firefox, MSN and Visual Studio opened. With C# I programmed a quick application to scan some pages with Internet Explorer. The site it was scanning was deviantART (which is pretty trustworthy), I doubt any banners there would hold a virus. I went to a suspicious site called freetxt.com but that was on Firefox and it didn't load the site. With an extra check I ping it and got this message "Ping request could not find host freetxt.com." The virus seems to be called braviax. Right now it brought up a message saying my computer may be infected? How on earth did it get in? I don't have uTorrent installed or any torrent or p2p applications. Nothing is installed on my computer that I haven't installed before and I know the exact time it installed because I see rkpg.exe on my C drive and my computer restarted on its own around the same time. For the previous 30 minutes actually the previous hour all I did was talk on MSN, not click any links (I went to freetxt on my own) and had that Internet Explorer thing running (which I programmed). How did it get in? I really doubt it came from a banner on deviantART and installed when I loaded the page with the webbrowser-control so something else may have happened? Is there any system defaults I should turn off? I have remote assistance off but even if it was on I shouldn't be infected due to the router not forwarding any ports?

  Read the article

• Windows Server 2003 IPSec Tunnel Connected, But Not Working (Possibly NAT/RRAS Related)

  - by Kevinoid

  Configuration I have setup a "raw" IPSec tunnel between a Windows Server 2003 (SBS) machine and a Netgear FVG318 according to the instructions in Microsoft KB816514. The configuration is as follows (using the same conventions as the article): NetA | SBS2003 | FVG318 | NetB 10.0.0.0/24 | 216.x.x.x | 69.y.y.y | 10.0.254.0/24 Both the Main Mode and Quick Mode Security Associations are successfully completed and appear in the IP Security Monitor. I am also able to ping the SBS2003 server on its private address from any computer on NetB. The Problem Any traffic sent from a computer on NetA to NetB, or from SBS2003 to NetB (excluding ICMP Ping responses), is sent out on the public network interface outside the IPSec tunnel (no encryption or header authentication, as if the tunnel were not there). Pings sent from a computer on NetB to a computer on NetA successfully reach computers on NetA, but the responses are silently discarded by SBS2003 (they do not go out in the clear and do not generate any encrypted traffic). Possible Solutions Incorrect Configuration I could have mistyped something, somewhere, or KB816514 could be incorrect in some way. I have tried very hard to eliminate the first option. Have re-created the configuration several times, tried tweaking and adjusting all the settings I could without success (most prevent the SA from being established). NAT/RRAS I have seen multiple posts elsewhere suggesting that this could be due to interaction between NAT and the IPSec filters. Possibly the NetA private addresses get rewritten to 216.x.x.x before being compared with the Quick Mode IPSec filters and don't get tunneled because of the mismatch. In fact, The Cable Guy article from June 2005 "TCP/IP Packet Processing Paths" suggests that this is the case, (see step 2 and 4 of the Transit Traffic path). If this is the case, is there a way to exclude NetA-NetB traffic from NAT? Any thoughts, ideas, suggestions, and/or comments are appreciated.

  Read the article

• PATH variable recently changed

  - by Dan

  $ loopy Command 'loopy' is available in '/usr/games/loopy' The command could not be located because '/usr/games' is not included in the PATH environment variable. loopy: command not found Every answer I've found just says to add it to my .profile... but this should be be in the PATH for all users, and was up until recently (I have no idea what would have caused it to change). How can I solve this on my system for all users? What could have caused this to change? Thanks.

  Read the article

• How to safely move where itunes saves music/iphone apps/and meta data to another internal Drive?

  - by GingerLee

  In the past, when I have moved my itunes data from one computer to another, I usually just follow these steps: Copy the contents of two folders: %USERPROFILE%\Music\iTunes %USERPROFILE%\AppData\Roaming\Apple Computer 1) Install iTunes on the new computer, start it and close it (don't let it search for music). 2) Copy all the files in the above folders from old PC to new PC. 3) Start iTunes and authorize the new computer (and deauthorize old one). 4) Before syncing, update all iphone apps to current versions on both my iphone and in itunes. 5) The Sync. The above steps always work for me, and basically Itunes on my new PC works exactly as it did on the old PC. My Question: In the hopes of bybassing the above steps in the future, I would like to just have Itunes use another internal Drive that I use for file storage (e.g. D:/) as the path for the above two directory? Then if I move to new PC again, I could just setup itunes to use the correct path. Is that possible yet with minimal implications? If so how?

  Read the article

• Installing a .NET framework on Windows 7?

  - by user23392

  I just switched to windows 7 from Vista and a lot of programs/games don't work anymore. The issue is that some games need a specific .NET framework version. when I try to install that it says that I should turn on/off windows features. I go to that and I find .NET framework in the list and tried both checking it and unchecking it. Both don't work and I still get the message that I need to turn on/off that thing. Any suggestion please? I have Windows 7 Ultimate 32-bit.

  Read the article

• pfsense 2.0 traffic priority - set full priority for single host

  - by Waxhead

  I have a network with several computers all on the same network and since I have very limited bandwidth I would like to prioritize traffic almost like a CPU scheduler prioritize processes. Example: Computer A: Used for webstuff: YouTube, downloads, news, emails etc. Computer B: Transferring files over HTTP Computer C: Transferring files over ftp, rsync whatever What I would like to do is to give A up to for example 90% of the available bandwidth IF A requires it. The leftovers (10%) is divided between B and C (5% each if both is busy) If A is not utilizing all bandwidth then of course B and C should share the full bandwidth (50% each as long as both are maxing out their bandwidth). All computers are on the same network (192.168.1.0 - 192.168.1-10 for example). Appreciate if anyone could shed some light on how I should set up my network to achieve this. To be honest I actually need a step by step guide on how I should set this up. Network setup: (ADSL modem configured in bridge mode (1500kbps/300kbps)) [ADSL modem (bridge)]<-[pfsense2.0]<-[switch]<-[Computer A,B,C...etc]

  Read the article

• What is the most important type of apps for new users? [closed]

  - by Nicu Zecheru

  What app do you think is most important for a new user (home users)? Office applications Browsing the web Playing games Email

  Read the article

< Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179  | Next Page >