Search Results

Search found 6033 results on 242 pages for 'partition magic'.

Page 172/242 | < Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179  | Next Page >

• Windows 7 Bootcamp to see data doubler SATA SSD in Optical Bay Connector

  - by bumble_bee_tuna

  Hi I purchased a OWC data doubler http://eshop.macsales.com/item/OWC/DDAMBS0GB/ ... Long story short it lets you add a second HD to your macbook pro in place of the cd/dvd drive (which is useless anyway, impossible to get stuff out when stuck). My current setup is 600gb intel SSD bootdrive 100gb partition for OSX / 500gb for Windows 7 Prof from Bootcamp (use 99 % of time). My desire is to have a second 300gb SSD to run disk intensive VM's off of. So I added a second 300gb intel SSD (again, NO desire to boot off of) on the sata optical port. I can see the drive no problem if I boot in to OSX, however, can't see it in disk management on Win7 ??? Any ideas similar experience ... Funny thing is I can see it in "Device Manager Disk Drivers" but not Disk Management ??? Also no I don't want to use Fusion/Parallels this is a waste of resources for me.

  Read the article

• HDD bad sectors with OS

  - by Michael Z

  I wonder is that possible for OS to make bad sectors on Hard Drive? Preface: I have bought new HDD on 1Tb WB Caviar Black. I have installed new OS on ext4 partition Ubuntu 12.04.1 LTS. After few days S.M.A.R.T. of the Ubuntu's Disk Utility show that my hard has bad sectors! I have checked on S.M.A.R.T. immediately after installing OS - all was OK. During new OS working I have noticed some strange with HDD - all OS was freezed from 20 sec to 1 min and I have heard like HDD's engine restarting. At the dmes I have found something like this: [40085.407947] ata1.00: device reported invalid CHS sector 0

  Read the article

• RHEL raw device (over VMware RDM) performance issues

  - by jifa

  I'm running RHEL 5.3 over vSphere 4.0U1. I configured multiple LUNs on my NetApp (Fibre) storage, and added the RDM on two (Linux) VMs, using the Paravirtual SCSI adapter. One LUN is 100GB in size, successfully mapped to /dev/sdb on both VMs, 5 more are 500MB in size (mapped to /dev/sd{c-g}. I also created one partition per device. I have encountered two issues: First, writing directly to /dev/sdb1 gives me ~50MB/s, while any of the /dev/sd{c-g}1 gives me ~9MB/s. There is no difference in configuration of the LUNs apart from their size. I am wondering what causes this but this is not my main problem, as I would settle for 9 MB/s. I created raw devices using udev pretty straightforwardly: ACTION=="add", KERNEL=="sdb1", RUN+="/bin/raw /dev/raw/raw1 %N" per device Writing to any of the new raw devices dramatically slows down performance to just over 900KB/s. Can anyone point me in a helpful direction? Thanks in advance, -- jifa

  Read the article

• Can I bind multiple forms to a single model using the default model binder?

  - by MedicineMan

  I have a complex page with several forms on it. The page is divided into sections, and each section has a continue button on it. The page is bound to a pageViewModel, each section addresses a different set of properties on the model. The continue button makes an ajax call to the controller, and the model binder binds it appropriately to the appropriate sections of the model. The section is refreshed appropriately. Finally, I would like to have a save button at the bottom of the page that takes all the forms, and binds all of the forms to the model. The model, at this point has all of the properties filled out, and can be processed accordingly. Can I accomplish this by some ASP MVC magic?

  Read the article

• AbsoluteTime with numeric argument behaves strangely.

  - by dreeves

  This is strange: DateList@AbsoluteTime[596523] returns {2078, 7, 2, 2, 42, 9.7849} But DateList@AbsoluteTime[596524] returns {1942, 5, 26, 20, 28, 39.5596} The question: What's going on? Note that AbsoluteTime with a numeric argument is undocumented. (I think I now know what it's doing but figured this is useful to have as a StackOverflow question for future reference; and I'm curious if there's some reason for that magic 596523 number.) PS: I encountered this when writing these utility functions for converting to and from unix time in Mathematica: (* Using Unix time (an integer) instead of Mathematica's AbsoluteTime... *) tm[x___] := AbsoluteTime[x] (* tm is an alias for AbsoluteTime. *) uepoch = tm[{1970}, TimeZone->0]; (* unixtm works analogously to tm. *) unixtm[x___] := Round[tm[x]-uepoch] (* tm & unixtm convert between unix & *) unixtm[x_?NumericQ] := Round[x-uepoch] (* mma epoch time when given numeric *) tm[t_?NumericQ] := t+uepoch (* args. Ie, they're inverses. *)

  Read the article

• Clone a 2TB WD Green internal drive with bad sectors to a 3TB partitioned external

  - by ron

  I have a 2TB WD Black drive and would like to simply do a straight clone from a failing 3TB drive to it. Both are SATA. Will I be able to just install the new drive alongside the faulty one and then do the clone/rescue attempt with ddrescue or is there a better method? The faulty internal drive mentioned has bed sectors although am usually able to boot into Windows 7 Ultimate with it and navigate and access all my programs. I have been attempting some trials with an Ubuntu Live CD using ddrescue but am not sure I'm doing it right. I have a 3TB WD my book essential external which is GPT and have created a separate 2TB partition on it which I am trying to clone to. I assume I need to format the new drive first to NTFS? Can I do that via the Ubuntu Rescue Remix 12-04 live DVD that I've been booting with?

  Read the article

• understanding mount -o bind

  - by Ionut

  Few questions after the following commands: mount -o bind /new_disk/home/user/ /home/user/ mount -o bind --no-mtab /new_disk/home/user/ /home/user/ What is the difference between the two commands other than " Mount without writing in /etc/mtab. This is necessary for example when /etc is on a read-only filesystem." What is the difference between mount -o bind and mount --bind ...if there are Let's suppose i don't know there is a partition mounted using -o bind --no-mtab...where can I find if there is any mound point with bind ? The only way i can detect this is grep user /proc/mounts but in that line there is no info abut bind. Thank you.

  Read the article

• remove disks or other media press any key to restart

  - by Sam I am

  I'm having an issue regarding a disk imaging process. I have a WinPE image that will re-partition, the hard drive, and put a boot-able image on it. When I run the imaging process from an initial state, I get the following error remove disks or other media press any key to restart If I run the process subsequent times, It will work as desired, but I'm still interested in getting the process to work the first time. How do I figure out what's going on here? what should I be looking at? I'm a little bit out of my depth here, I don't know what to do next

  Read the article

• Why C++ virtual function defined in header may not be compiled and linked in vtable?

  - by 0xDEAD BEEF

  Situation is following. I have shared library, which contains class definition - QueueClass : IClassInterface { virtual void LOL() { do some magic} } My shared library initialize class member QueueClass *globalMember = new QueueClass(); My share library export C function which returns pointer to globalMember - void * getGlobalMember(void) { return globalMember;} My application uses globalMember like this ((IClassInterface*)getGlobalMember())->LOL(); Now the very uber stuff - if i do not reference LOL from shared library, then LOL is not linked in and calling it from application raises exception. Reason - VTABLE contains nul in place of pointer to LOL() function. When i move LOL() definition from .h file to .cpp, suddenly it appears in VTABLE and everything works just great. What explains this behavior?! (gcc compiler + ARM architecture_)

  Read the article

• How do I SCP/FTP to a Coraid SR2421

  - by Pitto

  I need to save data to a Coraid SR2421. I am no expert and I'm trying to understand how this costy piece of hardware works. All I have is a Ethernet cable connecting my laptop and the coraid to a switch and the coraid's console with cursor blinking. Any kind of help would be greatly appreciated. edit and further explanation: I've tried using software on the coraid website but It's not working. So I've contacted the support and they sent me a file to upload on the coraid. It looks like if I upgrade coraid's firmware then I'll be able to use the coraid software on the windows side. That's why I'd need SCP/FTP or any kind of solution to copy a file in the partition that can be read from coraid console command line so I can launch the update command as requested. I hope I was a bit clearer now.

  Read the article

• Why don't Domain class static methods work from inside a grails "service"?

  - by ?????

  I want a grails service to be able to access Domain static methods, for queries, etc. For example, in a controller, I can call IncomingCall.count() to get the number of records in table "IncomingCall" but if I try to do this from inside a service, I get the error: org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'incomingStatusService': Invocation of init method failed; nested exception is groovy.lang.MissingMethodException: No signature of method: static ms.wdw.tropocontrol.IncomingCall.count() is applicable for argument types: () values: [] How do these methods get injected? There's no magic def statement in a controller that appears to do this. Or is the problem that Hibernate isn't available from my Service class?

  Read the article

• Using rsync with link-dest from HFS to NTFS

  - by Tom

  Hi, I'm having a problem with rsync. I'm on a Mac and I'd like to sync my everyday's changes from my HFS+ partition to my NTFS formated networked drive. Pretty simple, and everything goes well except that it syncs every file each times. Here's my script: #! /bin/sh snapshot_dir=/Volumes/USB_Storage/Backups snapshot_id=`date +%Y%m%d%H%M` /usr/bin/rsync -a \ --verbose \ --delete --delete-excluded \ --human-readable --progress \ --one-file-system \ --partial \ --modify-window=1 \ --exclude-from=.backup_excludes \ --link-dest ../current \ /Users/tommybergeron/Desktop/Brainpad \ $snapshot_dir/in-progress cd $snapshot_dir rm -rf $snapshot_id mv in-progress $snapshot_id rm -f current ln -s $snapshot_id $snapshot_dir/current Could someone help me out please? I've been searching for like two hours and I still am clueless. Thanks so much.

  Read the article

• Get error (Repair Filesystem) 1 # when I install 4 new Hard drives in RedHat Linux 5 on a Dell PowerEdge 2900

  - by Alos Diallo

  Hi I am using a Dell PowerEdge 2900 running RedHat 5. I had 4 drives in the system using a Raid 5, I purchased and installed 4 more drives keeping the configuration the same. Set up the Vertual disks in PERC 6/i. When I exit out and reboot the system I get the following: fsck.ext3: No such file or dirrectory while trying open /dev/ddb1 [FAILED] ***An error occurred during the file system check. ***Dropping you to a shell; the system will reboot ***when you leave the shell. Then am prompted for the root pw. I enter it and am then prompted with: (Repair filesystem) 1# if I type fdisk -l I get some info on the disk along with: Disk /dev/sdb doesn't contain a valid partition table I am then prompted for (Repair filesystem) 2# If I reboot I am taken to the same screen again. The system was working before this happened. Does anyone know why this is happening and or what I can do to fix it? Thanks

  Read the article

• Sorting out mSSD acceleration on a Acer M3-581TG

  - by PhonicUK

  I recently purchased a Acer Timeline M3 Ultra, it ships with a 500GB HDD and a 20GB mSSD to use as a cache. First thing I did when I got it was format the drives and install a clean OS (on the HDD, the mSSD has nothing on it) - but now I can't figure out how everything needs to be configured in order to use the mSSD as a cache, it just looks like a standard storage drive. I've poked around in the BIOS and there is a SATA mode setting, but it only has one option (AHCI), most of the documentation I've seen on the subject says that the SATA controller needs to be in RAID mode otherwise 'Acceleration' isn't visible in the Intel SRT menu (which for me, it isn't) I've seen a few things that suggest I just need the correct partition layout, I tried this using fdisk from a Linux LiveCD but got nowhere. Any ideas? The laptop shipped with no recovery media so I'm marginally stumped. I don't have any issue with reformatting again if required.

  Read the article

• XP can't read data from transferred HD

  - by Alexander Miller

  Computer A, running XP, died. XP was installed on a fresh HD in computer B. Slaved data-backup HD from A was installed as slave on B. B will not read it; shows only 2 folders, Recycler and System Volume Info. All of these are older machines with IDE drives. What's going on & how can I read/transfer the data from the transferred drive? This was only a trial run. Actually I will need to transfer the master HD from A - which has XP on it - and read from its data partition because (blush) the backup drive was not up to date.

  Read the article

• How to rename a BTRFS subvolume?

  - by hochl

  I have a BTRFS filesystem with a set of subvolumes in it. So far so good. I need to change the name of a subvolume, unfortunately the btrfs program does not allow me to rename a subvolume. Searching with Google has yielded some results, one said I can just mv, the other said I can just snapshot to a new name and delete the old subvolume. Before I crash my partition and have to reload it from the backup (it's quite large), my question is: What is the currently best way to rename a subvolume? Is it ok to just mv it, or will it invalidate some internal structures? Is making a new snapshot and removing the old subvolume the way to go, or has this some drawbacks? I know everything is still experimental, but for my purposes it has been working quite well (so far, and I have incremental backups for each day).

  Read the article

• C inline assembly of x96 fbstp instruction

  - by David HUnter

  Was wondering how to inline a usage of fbstp on a 32 bit I86 architecture. I tried something like int main( ) { double foo = 100.0; long bar = 0; asm( "pushl %1; fbstp %0" : "=m"(bar) : "r"(foo) ); ... But bar is unchanged. I have tried reading everything I can find on this but most example simply do things like add two integers together. I can’t find any that talk about pushing operands onto the stack and what I should be doing when an instruction like fbstp writes 80 bits of data back to memory ( i.e. what C type to use ) and how to specify it in the asm syntax. Also on x86-64 there seems to be a pushq and no pushl but fbstp still exists whereas fbstq does not. Is there some other magic for 64 bit.

  Read the article

• Rails way for querying join table in has_and_belongs_to_many

  - by Michelle

  I have a user model and a role model with a has_and_belongs_to_many reliationship. The join table is roles_users (two columns - the PK of the user and the role) and has no corresponding model. I want to have a method that returns all users with a given role. In SQL that'd be something like SELECT u.id FROM role.r, roles_users ru WHERE r.role_id = #{role.id} AND r.role_id = ru.role_id I see that Rails' activerecord has a find_by_sql method, but it's only expecting one results to be returned. What is the "Rails Way" to give me a list of users with a given role e.g. def self.find_users_with_role(role) users = [] users << # Some ActiveRecord magic or custom code here..? end

  Read the article

• Howto boot directly into a VirtualBox image?

  - by mawimawi

  I have a running setup as following: Native OS: Windows 7 64bit, 3 Partitions: c: (System) d: (FAT32, here is my vdi file) e: (unformatted) VirtualBox: Fedora 14 running off the vdi file on drive d. Usually this setup is great for me, but sometimes I'd like to run Linux natively, and not inside VirtualBox. Is there a way to boot directly into the vdi file without the Windows overhead? E.g. using a USB stick with some modified Linux Kernel / GRUB that can mount the vdi file directly as "/"? Or copy the contents of my vdi file to the empty partition and somehow use this from VirtualBox (when booting into Windows) AND directly booting into Linux? Hope to get some hints or even howtos.

  Read the article

• Howto boot directly into a VirtualBox image?

  - by mawimawi

  I have a running setup as following: Native OS: Windows 7 64bit, 3 Partitions: c: (System) d: (FAT32, here is my vdi file) e: (unformatted) VirtualBox: Fedora 14 running off the vdi file on drive d. Usually this setup is great for me, but sometimes I'd like to run Linux natively, and not inside VirtualBox. Is there a way to boot directly into the vdi file without the Windows overhead? E.g. using a USB stick with some modified Linux Kernel / GRUB that can mount the vdi file directly as "/"? Or copy the contents of my vdi file to the empty partition and somehow use this from VirtualBox (when booting into Windows) AND directly booting into Linux? Hope to get some hints or even howtos. EDIT: yes, sorry. not programming related. I posted the question to serverfault.com (hopefully that's the better site for my question.)

  Read the article

• Ubuntu dual boot and grub error 18

  - by srboisvert

  I've attempted to install 9.04 on an older toshiba laptop with a new 300GB drive and am getting the dreaded Grub error 18 that indicates that grub is looking beyond the bios readable area of the HD and failing. I just let ubuntu roll with its default selections when installing and ended up with this: Drive layout /dev/sda1 -ntfs 128GB -boot /dev/sda2 -extended 170GB -lba /dev/sda5 -ntfs 167.59GB /dev/sda6 -ext3 2.33GB /dev/sda7 -linux-swap 172MB I'd like make the system dual bootable without having to reinstall windows (real pain since I would have to go through an obstructionist IT dept). I know I can make windows bootable with a rescue disk and fixmbr but is there something I can do to make it dual bootable using the ubuntu livecd? Alternately, what should I have done at the partition stage of ubuntu installation to avoid this?

  Read the article

• Jquery autocomplete for input form, using Textpattern category list as a source

  - by John Stephens

  I'm using the Textpattern CMS to build a discussion site-- I have a firm grasp of XHTML and CSS, as well as Textpattern's template language, but PHP and Javascript are a bit beyond my cunning. On the input form to begin a new topic, users need to select a category from a list of over 5,000 options. Using the HTML select-type input element is very unwieldy, but it works. I would like to use some kind of Javascript magic to display a text-type input element that will read user input and display matches or autocomplete from the available categories, passing the required option's value into the appropriate database field. I've seen several autocomplete plugins for jquery, but the instructions presuppose that you understand how Javascript works. As I mentioned above, it's easy for me to generate the category list as a select-type input element, and I can hide that element using CSS. Is it possible to control select-list input using an autocomplete mechanism in a text-type input element? How would I do that?

  Read the article

• Uninstalled Ubuntu, no GRLDR?

  - by user32965

  So I'm a big fat idiot. I installed Ubuntu 11.04 on my school's laptop, and here's come the time that I have to turn it back in. I wrote GRUB to the Master Boot Record, thinking it wasn't going to be permanent. So, fast forward to yesterday. I decided to hell with this, and popped in my Windows 7 CD, deleted the whole partition, formatted to NTFS, and installed Windows 7 on it. I'm surfing the web and my computer overheats [totally typical] I boot up, and get this: Try (hd0,0): FAT32: No GRLDR Try (hd0,1): invalid or null Try (hd0,2): invalid or null Try (hd0,3): invalid or null Try (hd1,0): NTFS5: No grldr Try (hd1,1): invalid or null Try (hd1,2): invalid or null Try (hd1,3): invalid or null Cannot find GRLDR. Press space bar to hold the screen, any other key to boot previous MBR... Timeout: 5 The timeout part just counts down to 0 from 5. I need to turn in this thing before tomorrow, please please please can someone help me out?

  Read the article

• UBUNTU.. GRUB problem

  - by pravinp

  Hi, I have/(had) windows xp on one partition of my hdd. on second i installed ubuntu 9.10 yesterday. and after reboot of windows xp i get error "GRUB LOADING.". now i know that you can play around with that using live GRUB and all. putting GRUB on top of MBR or etc etc. something like that. i want to know - if i reinstall Ubuntu 10.04 which is available now - will it give me still the same error? or i will be able to use both OS? (i.e. is that problem solved in version 10.04 or still there? and if it is solved reinstallation of ubuntu will solve the problem or not?) anyhelp is welcome. Thanks

  Read the article

• Video converters don't work anymore after reinstalling Windows

  - by tassiekev

  A few days ago, I decided to reinstall Windows 7 as my HD partition seemed to be nearly full and things were slowing down. I'd been using Handbrake almost exclusively to convert TV recordings and used Freemake on occasion. Following the reinstall, I can't get either to work: Handbrake says it's encoding for about 2 seconds and then says it's finished, but there are no converted files of any size. Freemake just says 'Conversion Error' and won't go any further. As an experiment I tried two programs that I don't normally use, VideoReDo & Any Video Converter. Both worked fine. Anyone got any clues?

  Read the article

< Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179  | Next Page >