trouble shooting - Page 172

Single application through OpenVPN tunnel (Debian Lenny)

- by mikael

I'm using Debian Lenny and I want to tunnel rtorrent only through a OpenVPN tunnel. I have a tunnel running, the config file looks like this: client dev tun proto udp remote openvpn.xxx.com 1194 resolv-retry infinite nobind persist-key persist-tun ca /etc/openvpn/xxx/keys/ca.crt cert /etc/openvpn/xxx/keys/client.crt key /etc/openvpn/xxx/keys/client.key tls-auth /etc/openvpn/xxx/keys/tls.key 1 ns-cert-type server comp-lzo verb 3 auth-user-pass script-security 3 reneg-sec 0 My idea is that I could run a sockd proxy internally that redirects traffic to the openvpn tunnel. I could use the *nix "proxifier" application "tsocks" to make it possible for rtorrent to connect through that proxy (as rtorrent doesn't support proxies). I have trouble configuring sockd as my IP inside the VPN changes every time I connect. This is a config file someone said would help: http://ircpimps.org/sockd.conf As my IP changes at each connect I don't know what to put in that config file. I have no control over the host side config file. Any help wanted. Any other method is very welcome.

Read the article

Bad results converting PDF to EPS on Linux

- by Tim

I'm having some trouble converting PDFs (created by Adobe Illustrator on a Mac) to EPS. I have tried several things but I am wondering if there is a better option. The following list is ordered by decreasing quality: inkscape --export-area-page --export-eps=out.eps in.pdf using the graphical program Inkscape works best, but is a bit slow; pdftops -eps in.pdf out.eps uses Poppler and works good and is fast; pdf2ps in.pdf out.eps uses ghostscript and works ok for simple documents; convert in.pdf out.eps uses ImageMagick and always rasterizes the image. I haven't tested the following: acroread -toPostScript use acroread (Linux only) Some issues I've found: Transparency is not supported in EPS, but instead of flattening the layers, most programs rasterize the image producing big files and ugly graphs. Inkscape does this best by only rasterizing the unsupported area. Gradients are rendered properly by Inkscape, but Poppler somehow chops up the gradient into many shapes of different colors. Greek symbols are seemingly not supported by Ghostscript and are rasterized (using pdf2ps). What are your experiences for this kind of task? Did I forgot certain programs and/or command line options that improve quality? I found some posts on this, but not a (thorough) comparison of possibilities, please correct me if I'm wrong. Related posts How to convert PDF to EPS? on TeX

Read the article

OpenLDAP Authentication UID vs CN issues

- by user145457

I'm having trouble authenticating services using uid for authentication, which I thought was the standard method for authentication on the user. So basically, my users are added in ldap like this: # jsmith, Users, example.com dn: uid=jsmith,ou=Users,dc=example,dc=com uidNumber: 10003 loginShell: /bin/bash sn: Smith mail: [email protected] homeDirectory: /home/jsmith displayName: John Smith givenName: John uid: jsmith gecos: John Smith gidNumber: 10000 cn: John Smith title: System Administrator But when I try to authenticate using typical webapps or services like this: jsmith password I get: ldapsearch -x -h ldap.example.com -D "cn=jsmith,ou=Users,dc=example,dc=com" -W -b "dc=example,dc=com" Enter LDAP Password: ldap_bind: Invalid credentials (49) But if I use: ldapsearch -x -h ldap.example.com -D "uid=jsmith,ou=Users,dc=example,dc=com" -W -b "dc=example,dc=com" It works. HOWEVER...most webapps and authentication methods seem to use another method. So on a webapp I'm using, unless I specify the user as: uid=smith,ou=users,dc=example,dc=com Nothing works. In the webapp I just need users to put: jsmith in the user field. Keep in mind my ldap is using the "new" cn=config method of storing settings. So if someone has an obvious ldif I'm missing please provide. Let me know if you need further info. This is openldap on ubuntu 12.04. Thanks, Dave

Read the article

Why should one have a secondary DNS server?

- by Sam Levin

I'm very confused. I basically understand how DNS works. Here's an example that helps illustrate what I'm having trouble understanding. Right now, I run a small web-server. I use my provider's DNS manager, so I don't have a DNS server hosted on the machine. Let's say for a second, that I don't use my host's DNS, and I decide to set up a DNS server on my server. Hypothetical scenario: my server (entire) server goes down - DNS included. Why do I need backup DNS? If the server is down, who cares if the DNS server is down too, considering that even if I had DNS up (it wasn't on the crashed server), it wouldn't be able to forward requests anyway since the server would be down? Is the point of having secondary DNS, to be able to change the IP addresses that your DNS server points to, so if your webserver was down, you could redirect traffic to a backup? How would you switch to the secondary provider, in the event that your main DNS provider becomes unavailable? Is a backup DNS system basically up all the time? How is it configured? Is it just an exact clone of the DNS server you would have on your server? Do they run simultaneously? Hopefully someone can see what I'm hung up on, and provide some guidance. Thanks

Read the article

Openldap, groups, admin groups, etc

- by Juan Diego

We have a samba server as PDC with OpenLDAP. So far everything is working, even windows 7 can log on to the Domain. Here is the tricky part. We have many departments, each department has it's own IT guys, and these IT guy should be able to create users in their department and change any info of the users in their department. My Idea was to create 2 groups for each department, For example: Department1 and Admins Department1. Admins Deparment1 has "write" priviledges for members of group Department dn: ou=People,dc=mydomain,dc=com,dc=ec objectClass: top objectClass: organizationalUnit ou: People dn: cn=Admins,ou=Group,dc=mydomain,dc=com,dc=ec objectClass: groupOfNames objectClass: top cn: Admins dn: cn=Admins Department1,cn=Admins,ou=Group,dc=mydomain,dc=com,dc=ec objectClass: groupOfNames objectClass: top cn: Admins Department1 member: uid=jdc,ou=People,dc=mydomain,dc=com,dc=ec structuralObjectClass: groupOfNames I dont know if you should make Department1 as part of Domain Users dn: cn=Deparment1,cn=Domain Users,ou=Group,dc=mydomain,dc=com,dc=ec objectClass: groupOfNames objectClass: top cn: Deparment1 member: uid=user1,ou=People,dc=mydomain,dc=com,dc=ec Or just create the deparments like this. dn: cn=Deparment1,ou=Group,dc=mydomain,dc=com,dc=ec objectClass: groupOfNames objectClass: top cn: Deparment1 member: uid=user1,ou=People,dc=mydomain,dc=com,dc=ec I seems that when you use smbldap tools bydefault the users are part of Domain Users even if you dont have them as part of Domain Users in the memberUid attribute, when I use finger they showup as part of the Domain Users group. I dont want the Departments Admins to be Domain Admins because they have power over all the users, unless I am mistaken. I also have trouble with the ACLs. I was trying to create an acl for members of this Admins group, I was trying with this search, but didnt work ldapsearch -x "(&(objectClass=organizationalPerson)(member=cn=Admins Department1,ou=Group,dc=mydomain,dc=com,dc=ec))" I am open to suggestions.

Read the article

What could cause a WMV to not play to completion in a browser?

- by Ty W

A realtor has had videos created for a community she is selling homes for, the people who made the videos gave them to us in WMV format. I can play these videos without any problem in Windows Media Player, VLC, and Quicktime (via Flip4Mac). I can play the videos from their location at videohomeguide.com in my browser without any trouble. However when I upload the files to our server the video stops at about the 1 minute mark in Safari and FireFox on Mac OS X Snow Leopard. I'm not sure if Windows browsers have the same issue because they are loaded using Windows Media Player. http://carolepaul.com/images/uploads/cottageslsjamestown.wmv <- our server, will fail at 1:09ish. http://www.videohomeguide.com/media/cottageslsjamestown.wmv <- should play to completion (3:27ish) The files generate the same MD5 hash on my desktop and on our server. I used WGET to transfer the files, always downloading from videohomeguide.com. Since the files are identical and are playable using VLC/WMP/Quicktime, and playable in the browsers from videohomeguide.com it seems to me that it is some sort of server config... maybe incorrect headers sent to the browsers? Here are the headers sent and received by FireFox on OS X: http://carolepaul.com/images/uploads/cottageslsjamestown.wmv GET /images/uploads/cottageslsjamestown.wmv HTTP/1.1 Host: carolepaul.com User-Agent: Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.6; en-US; rv:1.9.2.2) Gecko/20100316 Firefox/3.6.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 115 Connection: keep-alive HTTP/1.1 200 OK Date: Mon, 29 Mar 2010 20:43:20 GMT Server: Apache/1.3.41 (Unix) PHP/5.2.6 FrontPage/5.0.2.2635 mod_psoft_traffic/0.2 mod_ssl/2.8.31 OpenSSL/0.9.8b Last-Modified: Wed, 02 Dec 2009 18:08:46 GMT Etag: "1e7919c-198eadc-4b16ad2e" Accept-Ranges: bytes Content-Length: 26798812 Keep-Alive: timeout=10, max=200 Connection: Keep-Alive Content-Type: video/x-ms-wmv

Read the article

New hard drive for backup? [closed]

- by glaeven

I have come to realize that I need another external drive to use with my MacBook Pro. I currently have a 1TB WD MyBook Essential that I have been using for about a year and a half. I have it currently partitioned into two drives, one for backup (I named it Leonov) and one for movies, TV shows and other large files I don't need very often (I call that side Discovery One). I use Time Machine for backups since it is completely automated and I can restore from it without much trouble (I have had to at least three times now). As of now, Leonov is full enough that every backup deletes an old one and Discovery One is approaching it's limits. I would like to get a new drive and move one of the sides to it. What are some reliable, external (~1TB) drives for under or around $100? Would it be easier to move the movies (et al.) or the backups to the new drive? I also feel like I should say that all of my important documents (for school and the like, just not my music) are also synced to Dropbox as another form of backup and access.

Read the article

IIS 7.0 404 Custom Error Page and web.config

- by Colin

I am having trouble with a custom 404 error page. I have a domain running a .NET proj with it's own error handling. I have a web.config running for the domain which contains: <customErrors mode="RemoteOnly"> <error statusCode="500" redirect="/Error"/> <error statusCode="404" redirect="/404"/> </customErrors> On a sub dir of that domain I am ignoring all routes there by doing routes.IgnoreRoute("Assets/{*pathInfo}"); in the .NET proj and I want to put a custom 404 error page on that and any sub dir's of Assets. The sub dir contains static content like images, css, js etc etc. So in the Error Pages section of IIS I put a redirect to an absolute URL. The web.config for that dir looks like the following: <system.webServer> <httpErrors> <remove statusCode="404" subStatusCode="-1" /> <error statusCode="404" prefixLanguageFilePath="" path="http://mydomain.com/404" responseMode="Redirect" /> </httpErrors> </system.webServer> But I navigate to an unknown URL under that dir and yet I still see the default IIS 404 page. I am also seeing an alert in IIS that reads: You have configured detailed error messages to be returned for both local and remote requests. When this option is selected, custom error configuration is not used. Does this have anything to do with the customErrors mode="RemoteOnly" in the site web.config? I have tried to overwrite the customErrors in the sub dir web.config but nothing changes. Any help would be appreciated. Thanks.

Read the article

/usr/bin/python (Python 2.4) was deleted on CentOS 5. I compiled from source but yum is still broken. How can I get everything back to the way it was?

- by Maxwell

I saw a lot of other questions like this but none of them answered the exact part I am having trouble with (actually installing the Python RPM). Someone on my system deleted /usr/bin/python and /usr/bin/python2.4 on my 64 bit CentOS 5.8 installation. I recompiled Python 2.4 from source, but now whenever I try to yum install anything I get the following error: [root@cerulean-OW1 ~]# yum install httpd There was a problem importing one of the Python modules required to run yum. The error leading to this problem was: No module named yum Please install a package which provides this module, or verify that the module is installed correctly. It's possible that the above module doesn't match the current version of Python, which is: 2.4 (#1, Dec 16 2012, 09:16:56) [GCC 4.1.2 20080704 (Red Hat 4.1.2-52)] If you cannot solve this problem yourself, please go to the yum faq at: http://wiki.linux.duke.edu/YumFaq I checked http://wiki.linux.duke.edu/YumFaq and it said the following: If you are getting a message that yum itself is the missing module then you probably installed it incorreclty (or installed the source rpm using make/make install). If possible, find a prebuilt rpm that will work for your system like one from Fedora or CentOS. Or, you can download the srpm and do a rpmbuild --rebuild yum*.src.rpm I tried going to http://rpm.pbone.net/index.php3/stat/4/idpl/17838875/dir/centos_5/com/python-2.4.3-46.el5.x86_64.rpm.html to install Python, which resulted in the following error: [root@cerulean-OW1 ~]# rpm -Uvh python-2.4.3-46.el5.x86_64.rpm error: Failed dependencies: python-libs-x86_64 = 2.4.3-46.el5 is needed by python-2.4.3-46.el5.x86_64 So I tried installing python-libs-x86_64, which resulted in the following: [root@cerulean-OW1 ~]# rpm -Uvh python-libs-2.4.3-46.el5_8.2.x86_64.rpm warning: python-libs-2.4.3-46.el5_8.2.x86_64.rpm: Header V3 DSA signature: NOKEY, key ID 192a7d7d Preparing... ########################################### [100%] package python-libs-2.4.3-46.el5_8.2.x86_64 is already installed file /usr/lib64/libpython2.4.so.1.0 from install of python-libs-2.4.3-46.el5_8.2.x86_64 conflicts with file from package python-libs-2.4.3-46.el5_8.2.x86_64

Read the article

Sun T5120: Memory issue with 8GB DIMMs, "Unsupported memory configuration"

- by watain

Read the article

Windows Server 2003 DC hangs after network drivers update

- by tcv

Earlier today, we attempted to update the Broadcom BCM5716C network drivers on a Windows Server 2003. (Dell PowerEdge T310, FWIW). Since then we have not been able to boot the server in any normal mode. Safe Mode works. Safe Mode with Networking and regular bootups hang at "Applying Network Settings." I haven't tried Last Known Good Configuration nor have I tried Directory Services Restore Mode. I should also mention that the longest I've allowed "Applying Network Settings" was perhaps 30 minutes. I spoke to Dell since the server is under a basic warranty. They sent me the original Broadcom drivers. The trouble seems to be, however, that since I can only boot in Safe Mode, I can't install the application package as given. In safe mode, I receive the error: "The system administrator has set policies to prohibit this installation." I can install the drivers independently, but that doesn't allow the NICs to work. The most I've been able to get are Code 10 errors on each NIC. I plan to get back to the site tomorrow to attempt installation of a different NIC. I'm wondering what else I can try.

Read the article

Why can't this user connect to domain share?

- by Saariko

Part of my reorganizing credentials in the domain, I have created several users that will be used solely for services (backup, LDAP, etc) The idea is that systems that need specific usage will use a user/service user, that will give them what they need. However, I am having trouble setting the correct needed data. For this example, I have a NAS (Ready NAS 1100 by Netgear), that runs it's own backup jobs. The job reads from a domain share: \domain\qa and copies all data to another location. When using the domain\administrator everything works. When I input the domain\srv.backup user I get an error connecting to the folder. The srv.backup is part of the 'Domain Admins' group, which is a member of 'Administrators' I thought there might be propagation issues, but even when the srv.backup user was a direct member of 'Administrators' the error still occurred. I have 2 DC's (W2K8R2 replicas) - I thought that could also cause a problem, AFAIKT it's not the issue. Sharing permissions are open to everyone The Security on the folder is as follow This is the test window from the NAS dashboard I doubled check that the 'srv.domain' is part of the 'Domain Admins' group As well as tried with a simple 1-9 password. What else do I need to check? thanks.

Read the article

Winamp question: Generating 'dynamic playlists' from file playlists -OR- mass-tagging by file playli

- by Daddy Warbox

I'm trying to think of a way to do this. I sort my songs into a variety of playlists corresponding to different 'moods' I might have as I listen to them, and some songs fit for more than one kind of mood (e.g. a jazz song might be 'stylish' and 'emotional', or something to that effect). I also give them star ratings for a general sort of opinion about them. I want to be able to filter and sort my media library by the moods I want or don't want, as well as by star rating. Anyone have a good way to do something like this? I can't seem to use Winamp's dynamic playlists to generate lists from existing filesystem playlists (e.g. songs in a given .m3u files). Hand-tagging files with Winamp's tag editor is a royal pain. It's trouble enough just giving a star rating and sorting into playlists as is. If there is there a way to mass tag songs within each playlist with mood words to allow me to create dynamic playlists, I'd be fine (for now). It'd be nice if I could do this via some kind of hotkey for each song, too. I'm looking to see if I can use a macro program or something to do that, though. Thanks in advance. P.S: Alternatively, would something like Foobar have functions like this? Note: Italics are recent edits.

Read the article

CentOS networking BNX2

- by james moore

Having some trouble with my NICs. The server starts fine and I can wget/ping etc. However, when I /etc/init.d/networking restart I then receive the following error: Bringing up interface eth0: bnx2: fw sync timeout, reset code = 1030009 SIOCSIFFLAGS: Device or resource busy Consequently, the task fails. I have searched around on google users suggesting to disable PNP in the BIOS but I see no option. Here is some system information: $ ethtool -i eth0 driver: bnx2 version: 2.0.8-rh firmware-version: bc 2.9.1 $ uname -a Linux host 2.6.18-238.9.1.el5 #1 SMP Tue Apr 12 18:10:13 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux $/sbin/lspci | grep Broadcom 04:00.0 PCI brodge: Broadcom EPB PCI-Express to PCI-X Bridge (rev c3) 05:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5700 Gigabit Ethernet (rev 12) 08:00.0 PCI brodge: Broadcom EPB PCI-Express to PCI-X Bridge (rev c3) 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5700 Gigabit Ethernet (rev 12) $ lsmod | grep bnx2 bnx2i 81704 0 cnic 109512 1 bnx2i libiscsi2 77765 6 be2iscsi,ib_iser,iscsi_tcp,bnx2i,cxgb3i,libiscsi_tcp scsi_transport_iscsi2 73945 8 be2iscsi,ib_iser,iscsi_tcp,bnx2i,cxgb3i,libiscsi2 bnx2 224780 0 scsi_mod 199001 15 mpt2sas,scsi_transport_sas,mptctl,be2iscsi,ib_iser,iscsi_tcp,bnx2i,cxgb3i,libiscsi2,scsi_transport_iscsi2,scsi_dh,sg,libata,megaraid_sas,sd_mod $ rmmod bnx2; modprobe bnx2 PCI: Enabling device 0000:05:00.0 (0158 -> 015a) PCI: Enabling device 0000:09:00.0 (0158 -> 015a) bnx2: fw sync timeout, reset code = 10300003 Any help would be appreciated as I am at a loss.

Read the article

Very strange networking problem in all computers in my house

- by Anthony

I have three computers in my house: One desktop (wired), and two laptops (wireless). I'm using Cox Communications (yes they suck), and yesterday they had a major outage. I know it was them because I called them up when I started losing connection to the internet. All the computers can connect just fine, but they don't have internet access. It just says "local only". The weird thing is, some of them work occasionally. For the first day my laptop was working perfectly, while all the other computers couldn't connect. Later on in the day it got reversed, and the desktop was the one with internet access. By the second day the problem on Cox's end was fixed, but we still had no access. I called them up and they reset my modem, and did the usual troubleshooting stuff. It never fixed the problem, but we found out that the problem had to do with conflicting IP addresses. My router was a Linksys WRT54G and it was about 5 years old. I figured it might have gotten damaged from the outage since it was so old, and now it's having trouble "fixing itself" and giving out the proper IP addresses. So I bought a new router, a Cisco Linksys E1000. I set everything up, and still the same problem. My computer has access right now (that's how I'm writing this), but no other computers seem to be able to get access. Is there possible damage to the modem? Can someone help me please? Sorry for this being so long.

Read the article

Bluehost Emails Getting Blocked

- by colithium

A site for my client has the run-of-the-mill "website with users" email pattern. Create an account, get an activation email. Get an email when a subscription is expiring, etc. The site is hosted on Bluehost and currently it uses php's mail() function. There isn't much configuration that is allowed (as far as I know). The trouble is, about a third of these emails disappear into the void. They aren't in spam or junk folders, there's no bounce message, they just cease to exist. I've read about Bluehost email troubles but I can't figure out what my options are for fixing it. These aren't marketing emails, ie they have user-specific information contained within them. I suppose if a solution offers a good templating system that would be fine. What are my options? Excerpt of headers when delivered to a Gmail address: Received-SPF: neutral (google.com: 00.000.000.000 is neither permitted nor denied by best guess record for domain of domain@box###.bluehost.com) client-ip=00.000.000.000; DomainKey-Status: good Authentication-Results: mx.google.com; spf=neutral (google.com: 00.000.000.000 is neither permitted nor denied by best guess record for domain of domain@box###.bluehost.com) smtp.mail=domain@box###.bluehost.com; domainkeys=pass [email protected]

Read the article

Multiple Internet connections, multiple networks and split access in Linux

- by Swapneel Patnekar

I am having trouble setting up multiple internet connections for split access in Linux. We have 3 internet connections from 3 different ISP's. We want to configure our Linux gateway machine such that our three internal networks 10.2.1.0/24, 192.168.20.0/24 & 192.168.2.0/24 use ISP1, ISP2 and ISP3 respectively in a split access manner. Outlined below is the layout/settings, Interfaces of the Linux Gateway connected to Routers: eth0: 10.1.1.2<---------->10.1.1.1(Internal Interface of ADSL Router)[ISP1] eth1: 192.168.15.2<------>192.168.15.1(Internal Interface of 3G Router)[ISP2] eth3: 192.168.1.2<------->192.168.1.1(Internal Interface of ADSL Router)[ISP3] Kindly note that none of the interfaces in the Linux gateway has a public static IP address. Routers of ISP1 and ISP2 get assigned a dynamic public IP address when connected to the Internet, router of ISP3 has been assigned a public static IP address. Interface of Linux gateway connected to a switch, eth4: 10.2.1.1(LAN Interface for ISP1) eth4:0 192.168.20.1(LAN interface for ISP2) eth4:1 192.168.2.1(LAN Interface for ISP3) eth4:0 & eth4:1 are virtual interfaces with eth4 being the interface connected physically. Based on http://linux-ip.net/html/adv-multi-internet.html I've set the following routes, ip route flush table 4 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table 4 $ROUTE done ip route add table 4 default via 192.168.15.1 ip rule add fwmark 4 table 4 ip route flush cache Additionally, using the following iptables rules to mark & route packets as per the guide mentioned above : http://pastebin.com/KzWHFGJA At this point, computers from 192.168.2.0/24 network are successfully able to reach the Internet through ISP3. 192.168.20.0/24 and 10.2.1.0/24 are unable to access the Internet through ISP1 and ISP2 respectively. Any inputs will be much appreciated !

Read the article

Linux Mounting Problem

- by Sam

I have an Iomega Network Attached Storage device on my Windows network. I am trying to use a clonezilla live USB flash drive to backup my netbook to my Iomega Network Attached Storage device. The clonezilla USB flash drive runs linux. I'm having trouble getting the Network Attached Storage unit to mount using the following command: mount -t cifs -o username="myUsername" //192.168.1.100/backup /home/partimg The response from linux is: [134.730738] CIFS VFS: cifs_mount failed w/return code = -6 retrying with upper case share name [134.788461] CIFS VFS: cifs_mount failed w/return code = -6 mount error(6): No such device or address Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) I also tried adding the following to my username: username="myUsername,domain=workgroup" but that did not change the error. I am able to ping the network attached storage unit from linux on my netbook. I also booted from a Slax Live USB Flash Drive and Slax auto-mounted my network attached storage unit via Samba. Unfortunately, I don't believe that I can run clonezilla from inside the Slax installation. Does anyone have any insight about what is wrong with my mount statement? Or is there something peculiar about Iomega drives which makes this impossible?

Read the article

Asterisk, IAXModem & Hylafax how-tos?

- by Brian Postow

I'm trying to set up Asterisk and IAXModem to send faxes via T38 (Yes, I know I'm swatting a fly with a Buick...) However, since I'm trying to do something so small with a product so large, I'm having trouble finding samples or how-tos that show me how to set this up. I've got all three installed, and I THINK I have my IAXModem config correct. I'm pretty sure that I have Hylafax correct (I've used it with T38Modem) so, I need to know which of the Asterisk samples I need to use, and how to use them. I think I want to use some combination of iax.conf, iaxprov.conf, sip.conf and sip_notify.conf. But I'm not sure where to put them, or what to change... I'm sure that the answer is RTFM, but I'm not sure WHICH M, or where in it to R... thanks. EDIT On a mailing list, someone told me that this actually WON'T WORK because IAX doesn't do T38. So, is there some other way to get Asterisk to work with Hylafax and send T38? I know that Asterisk does T38, the question is how to get the data from Hylafax and back...

Read the article

Cause of slow download speed on a particular EC2 instance?

- by James

I have a networking issue I'm trying to solve. I have two EC2 instances, same zone, same type. On one of the two EC2 instances (the 'bad' instance), the download speed is really poor (200k/s), while on the other (the 'good' instance), the download speed is fine, comfortable at 30M/s +). To clarify, I'm talking about downloading files to the EC2 instance while ssh'd into the server, e.g running wget with a large file. I've tried different files, including S3 objects and a large linux ISO from elsewhere. Running ethtool eth0 only returns 'Link detected: yes' for both. When running ifconfig, both return the same for most part, aside from how the good instance shows no error packets yet the bad instance shows many: UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:168372370 errors:5075643 dropped:0 overruns:0 frame:0 TX packets:122116480 errors:0 dropped:0 overruns:0 carrier:0 Both servers are configured the same, at least were supposed to be. How can I go about diagnosing the cause for the slow download speed? Is there anything particular to EC2 instances that could cause this? Having trouble knowing where to start. Thanks for any help!

Read the article

Compiled ruby fails to find curses

- by Hamish Downer

I'm attempting to install the sup MUA but I'm having trouble. When I try to run it, it can't find curses: /usr/local/lib/ruby/site_ruby/1.8/rubygems/custom_require.rb:31:in `gem_original_require': no such file to load -- curses (LoadError) ... I am installing on a server running CentOS 5. I have compiled ruby and rubygems from source, and then installed sup using rubygems. I followed this article to compile ruby. I have found having a similar problem on ubuntu. The fix suggested there is to install libcurses-ruby, but I can't find a similarly named package in CentOS. I have installed the ncurses-devel package, as that was required for installing sup using gem. I have also installed the ncurses, cursesx and rbcurse gems, but none of these have fixed the problem. The article above about compiling ruby said you had to recompile the zlib extension, after doing: cd ext/zlib sudo ruby extconf.rb --with-zlib-include=/usr/include --with-zlib-lib=/usr/lib cd ../.. sudo make sudo make install So I've tried a few variants in ext/curses. The top few lines of ext/curses/extconf.rb are require 'mkmf' dir_config('curses') dir_config('ncurses') dir_config('termcap') So I've tried a few variants of setting paths: sudo ruby extconf.rb --with-curses-include=/usr/include --with-curses-lib=/usr/lib --with-ncurses-include=/usr/include --with-ncurses-lib=/usr/lib --with-termcap-lib=/lib sudo ruby extconf.rb --with-curses-include=/usr/include --with-curses-lib=/usr/lib --with-termcap-lib=/lib and re-doing the make, but to no avail as yet. Any ideas to move it forward are welcome.

Read the article

Debugging "clogged" TCP connections

- by Nikratio

I'm having trouble with an internet connection that seems to randomly "freeze" arbitrary tcp connections. The connections stay established, but no data is coming through. When this happens, netstat still shows the connection status as ESTABLISHED on both the local computer: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name Timer tcp 0 53 192.168.0.10:41129 173.255.235.238:143 ESTABLISHED 8219/gnutls-cli on (79.31/13/0) ..and the remote server: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name Timer tcp 0 0 173.255.235.238:143 68.5.174.98:41129 ESTABLISHED 5303/imapd off (0.00/0/0) However, it seems that no data at all is transferred. If I run strace on the local and remote process, both just show a repeating sequence of select calls (with different fds of course), e.g. select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) The internet connection overall does not seem affected, I can still establish new connections to the same service on the same server without any problems. However, the affected local applications seem to be unaware of the problem and just hang. When I look at a packet capture of this connection on the client side, the last thing that happens is that the client transmits some data, then nothing happens for about 1100 seconds, and then several TCP Retransmission requests go out, with intervals increasing from 4 seconds to 130 seconds. No activity is captured after that. After about 10 minutes, the connection on the remote end disappears from the netstat (I wasn't able to catch any intermediate state), but still stays ESTABLISHED on the local end. Finally, after some more minutes, the local application aborts with a timeout and disappears from the local netstat output as well. Does anyone have a suggestion of how I could debug this further to find out where the problem lies and how to fix it? Additionaly and/or as a temporary workaround: is is there some way to globally reduce the timeout on client and/or server to reduce the time before the local application aborts?

Read the article

why is rdiff-backup not compatible with encfs ---reverse

- by user330273

I'm trying to use encfs with rdiff-backup to ensure that my backups to a remote server are encrypted. The easiest way to do this would be to use encfs --reverse - which means encfs will create a virtual encrypted file system, which I can then backup using rdiff-backup. Except that it doesn't work. Rdiff-backup fails every time with an "input/output error" on the encfs virtual filesystem. It seems I'm not the only one with this problem, but no one has said what the problem is: this person reported the same issue, but was just told to use sshfs instead (see below on that); in this question on serverfault, one of the answers just states that "rdiff-backup seems to have trouble accessing the EncFS-reverse filesystem." There's an open bug report on the Debian bug tracker(bug 731413, I can't post the link) on this bug, but it's been open since December 2013 with no response. Does anyone know what the problem actually is? Is there a workaround? I can't use the two most commonly suggested alternatives - sshfs and then running encfs on that, or using Duplicity - as both require a much higher bandwidth connection than I have access to (Duplicity requires regular full backups).

Read the article

MSE updating fails, no warning or error message.

- by WebDevHobo

I'm running Windows 7 Ultimate, 32-bit. For the last couple of days, MSE doesn't fails to update, remaining stuck at version 1.75.119 I presume that an error log is created somewhere, or an event log, but I don't know where to find those. It just says "connection failed". Tried it at home, at work and friends places, but never works. Restarted computer a lot of times now, checked for Microsoft Updates in general, but nothing shows up. EDIT: I've opened a bounty for this, because I really don't know what to do anymore. The oldest answer(the long post) here did not work. Besides this problem, I'm having trouble using MSI installers too. I've had to add the SYSTEM group to a lot of maps and give them full control, but shouldn't the SYSTEM already be there? Also, I had to remove the "read-only" attribute from the ProgramData and Users folders, add the SYSTEM group there too and give them full control. Only then will the MSI install work and even then, it says I doesn't have the rights to create a shortcut on the desktop. Don't know what I need to modify and where for that. I'm saying this because I don't know how MSE updates, but if they use MSI files to do that, that might explain things. The SYSTEM group remains added, but every time I take away the read only attribute, click OK and check the settings again, read-only is still active... That's all I know. Screenshot, all those updates were manual:

Read the article

Deploying concrete5 on nginx

- by Nithin

I have a concrete5 site that works 'out of the box' in apache server. However I am having a lot of trouble running it in nginx. The following is the nginx configuration i am using: server { root /home/test/public; index index.php; access_log /home/test/logs/access.log; error_log /home/test/logs/error.log; location / { # First attempt to serve request as file, then # as directory, then fall back to index.html try_files $uri $uri/ index.php; # Uncomment to enable naxsi on this location # include /etc/nginx/naxsi.rules } # pass the PHP scripts to FastCGI server listening on unix socket # location ~ \.php($|/) { fastcgi_pass unix:/tmp/phpfpm.sock; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_path_info; include fastcgi_params; } location ~ /\.ht { deny all; } } I am able to get the homepage but am having problem with the inner pages. The inner pages display an "Access denied". Possibly the rewrite is not working, in effect I think its querying and trying to execute php files directly instead of going through the concrete dispatcher. I am totally lost here. Thank you for your help, in advance.

Search Results

Search found 6433 results on 258 pages for 'trouble shooting'.

Page 172/258 | < Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179 | Next Page >

- by mikael

- by Tim

- by user145457

- by Sam Levin

- by Juan Diego

- by Ty W

- by glaeven

- by Colin

- by Maxwell

- by watain

- by tcv

- by Saariko

- by Daddy Warbox

- by james moore

- by Anthony

- by colithium

- by Swapneel Patnekar

- by Sam

- by Brian Postow

- by James

- by Hamish Downer

- by Nikratio

- by user330273

- by WebDevHobo

- by Nithin

< Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179 | Next Page >