Search Results

Search found 5693 results on 228 pages for 'ago'.

Page 174/228 | < Previous Page | 170 171 172 173 174 175 176 177 178 179 180 181  | Next Page >

• Strange boot problems on 6 month old setup

  - by Balefire

  I've already exhausted my knowledge on this one, so forgive me if this post is a bit long. I built a computer 6 months ago for my wife and it worked fine until last week. Then it randomly shut down and would lock up while trying to boot on the boot screen. I cleared cmos and it allowed me to do startup recovery, but it "failed to fix the issue" so I reinstalled windows on the HD (moving the old install to windows_old). It worked, so I started installing drivers again, but then when I restarted to finalize installations it locked up again. This time, I took the hard drive and hooked it up to my computer, backed up all her files, and then formatted the hard drive before reinstalling it. (again had to clear cmos to let me boot from disk) It installed windows, I installed drivers, and it worked for a few hours but then died during startup again. So, then I got a new HD, cleared cmos, and installed clean again, with the same result as the time before, it worked for a few hours, installed windows updates, then crashed on the 3rd or 4th time turning it on. I decided next to try reinstalling and then going online to see if there were any updates for the BIOS or drivers on the Motherboard, but now I can't get it to even bring up the boot menu, so now I'm just left wondering was it the motherboard, or is it the CPU, or the RAM? The problem was strangely intermittent so I thought it had to be a software issue, since a hardware issue would ALWAYS fail to boot, right? But now it seems to be a hardware issue, because it's not bringing up anything. Any suggestions? System: Windows 7 64-bit 970A-DS3 Gigabyte Motherboard AMD Phenom II X4 955 Deneb 3.2GHz Quad core Proc GeForce GT 430 (Fermi) 1GB Video Card 500W PSU 2 x G.SKILL Ripjaws X Series 4GB 240-Pin DDR3 1600 RAM

  Read the article

• Removing expired self-signed certificate in IE9 (created with IIS7.5)

  - by Itison

  Over 1 year ago, I created a self-signed certificate in IIS 7.5 and exported it. I then installed it for IE9 (it may have been IE8 at the time), which worked fine until a year later when the certificate expired. I have put this off, but today I created a new self-signed certificate in IIS, exported it, and attempted to install it in IE9. The problem is that for whatever reason, IE cannot seem to forget about the old, expired certificate. Here's what I tried initially: Accessed my ASP.NET application and see the Certificate error. Clicked "View certificates". Clicked "Install Certificate" and then Next/Next/Finish. At this point, it says the import is successful, but it still only shows the expired certificate. I've tried simply double-clicking on the exported certificate on my desktop. Initially I chose to automatically select the certificate store, but then I tried it again and manually selected "Trusted Root Certification Authorities". I've also tried dragging/dropping the certificate over an IE window and clicking "Open". The process is then exactly the same as it is if I had double-clicked on the certificate, but I had hoped that this would somehow specifically tell IE to use this certificate. I tried opening MMC and with the Certificate snap-in, confirmed that the new certificate was added under "Trusted Root Certification Authorities". It was also under my "Personal" certificates (I guess this is where it goes by default). Nothing worked, so I went through every folder in MMC and deleted the expired certificate. I also deleted the expired certificate in IIS. Nothing has worked. Any ideas? I see no clear resolution and I can't seem to find any posts related to this issue.

  Read the article

• Debian 100% cpu every 30 minutes but not loggable?

  - by user654123

  I have a Debian 7 x64 machine running with Digital Ocean that has every 30 Minutes a 100% cpu usage for about 1 minute. A couple of days ago it stayed there for a couple of hours so the server finally crashed and I had to repair my Mysql databases. The server is a pure webserver running apache2 and Mysql. I tried tracing which processes use the cpu but with no luck. The script I used: #!/bin/sh while true; do ps -A -eo pcpu,pid,user,args | sort -k 1 -r | head -3 >> proclog.txt; echo "\n" >> proclog.txt; sleep 2; done I was monitoring htop as well while this was happening, but the top processess' cpu usage didn't add up to ~15% even though htop's cpu meter showed constant 100%. htop was configured to show all users' processess, user- and kernel-threads. Edit: By stopping Apache2 & Mysql prior to the expected 100% usage I can tell both are not responsible for it. The 100% usage occurred anyway. This is what the graph looked like the past hours:

  Read the article

• How to change the MAC address in Win 8 to spoof a Roku Player through a WiFi splash page?

  - by luser droog

  My Linux laptop died yesterday and now I can't watch TV. Let me explain. I use a Roku Player to stream Netflix shows to my television; and a year or two ago, the Internet Service provided in my apartment complex added a Splash Page to get through the router and onto the net. After not too many days, I remembered that internet devices identify themselves with a MAC address. So I delved into the manpage of ifconfig and discovered that I could persuade my laptop to pretend to be the Roku Player, connect, click through the Splash Page, disconnect and change it back. This would allow the Roku to connect for about 24 hours, when I would have to do it again. But the laptop died yesterday during my smoke break. So during lunch, I ran to OfficeMax and got a new one. But I don't know where to begin looking for where to change the MAC address (assuming it's possible). I know I can try dual-boot, or a keychain OS, or possibly other things to resurrect my old method. But, is it possible to get Windows do it?

  Read the article

• php extensions & apache mods gone/not working after server restart?

  - by user1782359

  I was wondering if anyone has ever come across this before, as I'm pretty stumped to be honest, and my server admin knowledge isn't particular good so I'm not sure what could even be wrong, let alone how to fix it. Basically, Thursday last week everything was fine on our server. I come in on Friday and it's a mess: php extensions are missing/not working, apache modules are gone. (e.g. oci_* was gone completely, odbc_ not working but still there, the apache ntlm_auth for single sign on was gone and so the website wasn't even loading in IE). I'm ruling out anything deliberate because it's just incredibly unlikely. The only thing that really happened between thursday & friday is that on thursday evening one of the network guys did a RAM upgrade on the server and restarted it. That's it, nothing else. Now I'm wondering if somehow those extensions and such which we installed months ago were somehow only saved in a local memory of sorts, and a restart has wiped them? But we installed them all as root, so I don't see why it should be any different from installing anything else. It makes little/no sense to me. To expand on an example of something that's gone very wrong, the php odbc_ extension: It's still on the server, it doesn't return undefined function or anything. But it just cannot connect to the datasource any more. I've tested it through the command line and it's working perfectly fine with that datasource and login details, but all of a sudden having it in the php odbc_connect() function and it just can't connect. ( [S1000][unixODBC][FreeTDS][SQL Server]Unable to connect to data source. ) But unixODBC is set up fine. Like I say i've tested it all through the terminal and it can connect, and we've not changed anything, it's just now all of a sudden not working through the PHP function. Anyone have any ideas whatsoever as to what could be going on? This is on CentOS 5.x by the way.

  Read the article

• Are there any benchmarks showing difference between hardware virtualisation enabled/disabled?

  - by Wil

  I have a 13" sub-laptop/large-netbook, it has an AMD Athlon Neo X2 L335, and I chose this one because it supports hardware virtualisation. In the end, I hardly do any virtualisation on it, however, when I do... it is fast. To my shock, I went in to the BIOS and saw that virtualisation was disabled! I turned this on and, I see no speed difference.... or at least none that I can tell. I do not have time to do a full set of benchmarks - and I run quite a bit of software on the host, so it wouldn't be scientific. I have searched quite a few places and I just can not find any benchmarks showing the difference of virtualisation bit enabled/disabled on the same hardware. Does anyone have any benchmarks they have seen that they can share? In addition, I know there was an uproar a while ago as Sony disable the hardware virtualisation on some models and only offer it in their higher models as a premium feature, however, apart from forcing an up-sell, are there any benefits to having it disabled e.g. battery/heat? I just can't find any information and can't work out why it would be disabled by default. Edit--- To add, The only thing I can find is that without it, you can not perform x64 virtualisation as fast. This is the only down side I can find. However, if this is the only difference, then I am still interested in the second part of the question - why offer the option to disable it?

  Read the article

• What's Keeping My Computer Awake?

  - by phantomdata

  Hey guys, First the question; How do I figure out what is preventing my Windows 7 computer from going into sleep mode? Second; some background... I've been struggling with this for a few days and am utterly perplexed. I setup sleep mode on my Windows 7 PC a few weeks ago, and all was well. The PC would sleep as expected and I was snuggly in knowing that my computer was saving power and some wear and tear on the components (we'll leave the 'is it better to sleep' debate for another thread/day, please don't start it). Well, I noticed the other night that my system stopped ever going to sleep. I set the sleep time down to 1 minute and wandered fully away from the PC (ensuring that no errant mouse or keyboard movements would occur) and the PC never went to sleep. I've also observed this over longer intervals as well, such as overnight. I have sleep mode enabled, of course "multimedia settings - When Sharing Media" is set to allow the computer to sleep. "powercfg -lastwake" show nothing of interest, since it never goes to sleep and can't wake up. "powercfg /requests" shows 3 entries - all "[DRIVER] ?". I assume that 2 of these are my mouse and keyboard - as I've recently used them to run the powercfg command. I'm at a loss for the third though. I've unhooked all USB peripherals save for my keyboard and mouse. Wake on LAN is disabled in my BIOS. I know that you can disable all apps from waking/preventing sleep - but I want the ability to remain for those apps that do legitimately need to keep the system awake. So; does anyone know of a way to figure out what the 3rd phantom "[DRIVER] ?" is in powercfg /requests?

  Read the article

• Replacing Failing RAID 1 Drive

  - by mrduclaw

  I hope this is a simple question, but I simply don't know anything about RAID. Some time ago I received a machine that, as I understand it, has two drives in it under RAID 1 (or so that one drive is mirrored on the other and appears as just 1 drive to the OS). Recently, one of these drives has started marking a clicking noise and I would like to replace it. I believe the machine has a hardware RAID controller on the motherboard that handles the RAID stuff, but if it matters the Operating System is Windows XP 32-bit. Is the solution to my problem as simple as buying another drive that is of the same capacity and plugging it in where the clicking drive is currently? Or could I possibly lose everything if the drive that's clicking is the one being mirrored on to the other drive? Is there some menu I need to find before unhooking things? Any best practices out there? I'm sure I'm leaving out some required information, so please just tell me what I'm missing. Thanks!

  Read the article

• Intranet machines refuse to talk anymore

  - by ashes999

  I have two machines on the local intranet. They used to be able to talk to each other (ping, share files, etc.). Both are not successfully connected to the internet. The problem machine (lets call it test machine) can't talk to my main machine. The test machine can ping other machines on the intranet (at least one of my coworkers), but not mine. Odd. When I try to ping it from my machine, by machine name, I get Destination host unreachable. Both machines are on the intranet, with the network configured as Work Both machines have Windows Firewall disabled temporarily Both machines can talk to the internet (Google, SO, etc.) Neither machine can ping the other I need help resolving this. What I really want to achieve, is to remote into the test machine from my main machine, like I used to be able to do a few weeks ago. Some notes: Tried arp -a on both machines. I don't see the other machine's IP listed. Both machines have stable IPs; neither seems to have an IP conflict The configuration under ipconfig /all on my main machine mathces my coworker's machine. The test machine can ping his machine, but not my machine. The target machine times out trying to ping the main machine; the main machine gives me Destination host unreachable. I have rebooted both machines (several times) to no avail I have /release and /renewed both machines several times

  Read the article

• AWS instance went down for restart, came back up and has been "Waiting for network configuration... " for 12 hours

  - by kavisiegel

  What happened was about a month ago, I created a new instance, re-configured everything, and mounted the old instances drive to the new one. I then detached the old drive from the instance, but it was still mounted, so it errored out. Now, come the outage last month, and when the instance boots back up - the drive isn't there, because in the downtime, it dismounted. It hangs because the fstab is looking for it. I get word that the server's not up today, I check the logs, re-attach the drive and restart. Now I'm getting "Waiting for network configuration..." and it doesn't seem to be doing anything. Some googling told me that I'm going to need to start from zero again, which I don't think is right. I created a new instance, which booted no problem, then I stopped it and swapped the two old drives into the new instance. Still the same error. Using the fresh AMI, it worked. I figure it's just a misconfigured Amazon file. I can attach the drive to a functioning instance on the same AMI and copy some files over, then try again - but I don't know where to even start or what files to check.

  Read the article

• Timestamp Updating Constantly on /dev/null

  - by motorleague

  I've been working on a problem with a /dev/null file on an AIX system (just for background it looks as though it was inadvertently deleted and recreated as a normal file by somebody), but in trying to determine what caused the problem, I noticed that the timestamp on it seems to update every minute. I've observed this on several AIX servers at my workplace. At present I can't entirely rule out this be something specific to the Application being used at my workplace, so I compared with CentOS and Debian based computers at home last night. The CentOS box, which runs 24 hours, had a mod time on /dev/null of around 4 days ago (during which time it was essentially just being used as a web browser and multimedia player, although it would have had active but essentially unused Apache, MySQL and VMM processes running in the background). The timestamp on /dev/null on the Debian machine, which was a just booted laptop, pretty much reflected the boot time, but I tested redirecting STDIN from, and STDOUT to it, and the modification time was unchanged (I'm not sure 100% sure if directing data to /dev/null constitutes "writing to it" in the way it would a normal file). So my question is essentially, could anybody please offer any advice with regards to what circumstances (permissions changes etc.. aside) might cause the timestamp on /dev/null to update? Thanks very much for any suggestions. Alex.

  Read the article

• Computer turns on and off very quickly, then nothing, then works?

  - by hellohellosharp

  The strange nature of this problem is what is stumping me. I built my computer about 7 months ago using all new parts off of Newegg (not a kit or anything). One day, I wake up and turn on my computer. I press the power button and it turns on, but then back off after half a second. I press the power button again, this time nothing. I continue pressing the power button while at the same time turning the power supply on and off (to try and reset things). The power button still does nothing. But then, after about 5 minutes, WALLAH, it works just fine like nothing was ever wrong. It goes for an entire week working just fine. Then, one morning, the entire process starts again. I press the power button and it comes on and then right back off. I press the power button several times and nothing happens, and then it works again after a couple minutes of trying. What is going on with my computer?

  Read the article

• What are possible results/side effects if replication between DC's in a Windows domain is unable to occur?

  - by hydroparadise

  There's plenty of administration literature out there how to properly manage Windows servers. But in dealing with real life, things don't always occur like you want them to. In Microsoft's Windows Server 2003 Administrator's Companion, out of 1400+ pages, theres only one page that I could find when it comes up setting up additional domain controlers. They make it sound seemless and don't reveal a whole lot on what happens if "peer" DC's are unable to replicate. Down to the specific issue at hand, we had a DC go down about a month ago due to a bad RAID controller. There was nothing critical that waranted imediate attention, so bringing it back up got put on the back burner. A month later, we get the DC back up and running and everyting seemed ok. The next day, nobody is able to logon complaining that the "user does not exist" or "unable to establish a trust relationship". Knowing that I had just put the downed DC back on the network, I immediately took it back off the network and had everybody restart the workstations. After that, exchange was fine, shares became available, and everybody was able to log in. After doing some event log swimming, it would appear that everything started due to replication issues on the SYSVOL. I've read where you can force replication, but that would mean putting it back on the network. I am afraid to put the DC back on the network in fear that something else could go wrong. So, what other issues could one expect to run into where two DC's are unreplicated for over a month?

  Read the article

• Folder name in sidebar is changed, how to get it back?

  - by otakustay

  My OSX is Simplified Chinese, so the user folders in finder's sidebar is like this: AirDrop ???? ?? ?? ?? ?? ?? ?? These stand for AirDrop, Applications, Desktop, Documents, Downloads, Movies, Musics and Pictures. However, now with an accident, my "Downloads" folders in sidebar is changed to its original english name, and I don't why, so my sidebar is now look like: AirDrop ???? ?? ?? Downloads ?? ?? ?? I know do symbol link to these folders would cause such case but I cannot find any symbol links to my ~/Downloads folder. So is there any way to get the Chinese name back? it looks so weired and dirty. I have a time machine backup 3 days ago, but I have quite a lot modifications to my user folder these 3 days, so time machine may not be a good choice.

  Read the article

• sendmail appends server name to external domains when relaying

  - by Chris

  My server is set to send all email to a corporate relay server. For the company domain, it works perfectly. I've recently found emails being sent to an outside domain are getting the hostname of my server appended to the email prior to being sent. Here is the log entry for one such attempt. Nov 6 09:46:45 myservername sendmail[45023]: rA6EkjiI045023: [email protected], delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30590, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (rA6Ekj2g045037 Message accepted for delivery) Nov 6 09:46:45 myservername sendmail[45061]: rA6Ekj2g045037: to=<[email protected]>, delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=120885, relay=relay.company.com [x.x.x.x], dsn=2.0.0, stat=Sent (ok: Message 342335947 accepted) Notice the email address difference between it being accepted by my server for delivery (correct email address), and being sent and accepted by the corporate relay (incorrect with server name appended). To make it more interesting, the application on my server uses email for user account verification/activation. In August, this particular user was able to register his account and activate it. I have made no configuration changes to mail since setting the server up over a year ago. DNS is also a corporate service. I've never touched my /etc/resolv.conf configuration. domain company.com nameserver <ip1> nameserver <ip2> search myservername Thanks!

  Read the article

• Same script, different behavior [migrated]

  - by Antoine_935

  I just stumbled upon an interesting bug... Still trying to figure out what is exactly happening. Maybe you can help. First, the context. I'm currently building yet another man to html converter (for some reasons I won't motivate here, but I need it). So, have a look at the screenshot below (see the link), more precisely at the outlined spots. See? On the upper shell, I have &lt ; and &gt ;, that is, escaped html. While on the shell below I have < and directly. But as you can see (or do I seriously need looking glass ?), the command man 2 semget | webmanneris the same on both sides, as is the which webmanner. The two are executed roughly at the same moment, with no modification made to the script between. [Oops, cannot post pictures just yet... Here comes the link] http://aspyct.org/media/webmanner-bug.png But the shell below is older (open about 1 hour ago). Newer shells all print out &lt ;. So my first guess was that it somehow had a cached reference to the old inode of the file, or old blocks or whatever. So I modified parts of the script, at the start and then at the end, to print different messages. And, surprise, the message shown up on both terminals. But still, same difference between &lt ; and <. I'm confused... How to explain that behavior? I'm working on a OSX 10.8 (Mountain Lion) EDIT: OK, there is one big difference: the shell below uses ruby 1.9.3, while above is 1.8.7. Is there any known difference in string handling between the two versions ?

  Read the article

• Pc sometimes turns on sometimes not

  - by cprogcr

  Some time ago, the PC gave the same problem. It wouldn't turn on. When i pressed the button, it turned on but showed nothing. I had replaced the CPU and that seemed to work. I didn't use the PC that much, rarely you know. But now, after some time, it gives the same problem. It turns on, the front light is on, it makes the normal noise the pc makes when it's turned on , but if I try to shut it down by holding the power button it just doesn't work. So again, I tried replacing the CPU and it worked again. I kept it all day working, just to be sure, and sometimes I would restart it and it would work again. No problems at all. So I turned it off at night, and next morning it just would make the same problem. So I tried replacing the PSU. And it worked again. Now while I had the PC with the new PSU, i tried to insert the old CPU, and again, it would turn on. The same thing, tried restarting too, and it would work. But this morning the same problem happened. Edit: I also tried another CPU today and yet no signs of working. I don't know now what to think.

  Read the article

• Removed Old Domain Trust. Now Progress (9.1D) can't open DB File

  - by RLH

  My company has an old server, running Progress 9.1D on a Windows 2000 VM, which was used by our company OS (Vantage 6 by Epicor.) Vantage was our primary OS for a very long time. About 2 years ago, we migrated to a larger, corporate OS and we cancelled our service contract with Epicor. Yesterday, we removed an AD trust between the corporate domain and our old AD domain we used in the days of Vantage. After restarting the virtual server, I have been able to start the ProService for 9.1D Windows service, however, I can not get Vantage to start back up. When I run the application, I get the error in the message listed below. Transcript: ** Could not connect to server for database [progress db file], errno 0. (1432) How can I fix this? FYI, I haven't had to work with Progress in years and even then I wouldn't have considered myself a "novice"-- I'm even less knowledgeable than that title would suggest. Vantage had a lot of internal tools and I recall that Epicor support managed to prevent .pf scripts from being executed. If there was a Progress specific patch that needed to be applied, you had to do it within the Vantage software OR they had to remote into the machine to fix this. I may not be able to run a .pf script but I do know that I can log into the console-based server application. (Yes, I can't even recall which utility that was called. It is sad.) It's been a long time and I never had to digg into Progress that much. Please help and feel free to ask questions. If you need more info, I'll update this post.

  Read the article

• Ubuntu server 10.04 disconnects after short periods of inactivity on my site

  - by user57019

  I'm new to Ubuntu (installed it for the first time just a couple of days ago on my server). I've Ubuntu Server 10.04 and am just using the terminal, no GUI like Gnome. So far it's working pretty great except for one big thing. Whenever I go to sleep and there's no activity on my server (it's not a big site so active users drop to 0 during the night), the server kind of disconnects. The only thing that can bring the site back online is to restart the whole server. I've tried disabling powersaving by using setterm but that changes nothing. Even if I wake up the server by pressing any key or so the site wont go back online! I've tried just restarting both Apache and MySQL (I'm using LAMP-server btw) but not even that works. But as soon as I turn the power off and on at the server, everythings work like normal for a couple of minutes of inactivity (~5-15 minutes I'd guess) and then it's down again unless someone logs in to the site and is active. I was previously using XAMPP on my laptop with Windows XP and that worked 24/7 so I don't think it's anything with my router or ISP. This is driving me crazy! My site is down all the time I'm in school as I have no possibility to restart the server if it becomes offline. Does anyone have a clue to what could be wrong?

  Read the article

• Video adapter problem on new motherboard

  - by Dmitriy Matveev

  Something bad happened to my PC several days ago. I wasn't near my PC, so I have no idea about what happened it was just halted. When I tried to boot it was entering infinite loops of a few seconds power up (cpu, hdds, etc) and then power down. I've tried to boot the system with no additional components (that includes hdd, video, network adapters and even memory) connected and that didn't solved the problem, so I've made a decision that most likely it's either some a problem with power unit or with motherboard. I've tried to replace my power unit by another one (which was expected to be working) and the problem didn't resolved again. I've bought a new MB (ASUS P5KPL-AM SE) and tried to get it running with my old CPU and memory (I hope it's still alive). Since this MB include on-board video I've tried to run the PC without installation of mine video. The PC wasn't running and the BIOS was beeping one long signal following by two short (Does it means a video problem?). After that I've installed my video adapter to PCI-E slot and tried to boot the system again and the BIOS was beeping the same. I don't get it. I may expect some problem with CPU and/or memory since I don't know what happened to my PC (maybe some power failure or something different), but not with video and not with on-board video on newly bought MB. How can I understand what's wrong with my system now?

  Read the article

• Vim: auto-comment in new line

  - by padde

  Vim automatically inserts a comment when I start a new line from a commented out line, because I have set formatoptions=tcroql. For example (cursor is *): // this is a comment* and after hitting <Enter> (insert mode) or o (normal mode) i am left with: // this is a comment // * This feature is very handy when writing long multi-line comments, but often I just want a single line comment. Now if I want to end the comment series I have several options: hit <Esc>S hit <BS> three times Both of these afford three keystrokes, taken together with the <Enter> this means four keystrokes for a new line, which I think is too much. Ideally, I would like to just hit <Enter> a second time to be left with: // this is a comment * It is important that the solution will also work with different indentation levels, i.e. int main(void) { // this is a comment* } hit <Enter> int main(void) { // this is a comment // * } hit <Enter> int main(void) { // this is a comment * } I think I have seen this feature in some text editor a few years ago but I do not recall which one it was. Is anyone aware of a solution that will do this for me in Vim? Pointers in the right direction on how to roll my own solution are also very welcome.

  Read the article

• Pc freezes then wont boot. The fans spin, but HDD activity light is off

  - by Stuart

  I'm having a problem with my PC and this isn't the first time it's happened. For a few days now, when I turned my PC on, it didn't immediately start to boot up. The monitor said "No signal" and the machine just sat there although the power light was on and the fans were running. Then, after a few minutes, it would begin to boot as if nothing was wrong. Today I started my machine and it ran ok for about 10 minutes. Then the whole thing froze up and I had to shut it down and restart by holding the power button. When it rebooted, the same thing happened again and again and now finally it wont boot up at all. This happened before about 8 months ago. I ended up taking it to the shop after getting a blue screen. They replaced the HDD and upgraded it to windows 7 and it has worked fine since then. However, they charged an arm and a leg for the work and I dont want to have to go back there again. As this is a recurring fault I figure its a mechanical problem of some sort but I'm not sure what. Any ideas? Thanks for your help.

  Read the article

• Can my employer force me to backup my personal machine? [closed]

  - by Eric B

  Here's the background: Approximately 1.25 years ago, the company I work for was acquired by a larger 400 person company. Before acquisition (and today still) we are all remote employees using our own personal hardware for work-related duties (coding, email, etc). We are approximately 15 employees within the larger organization. Some time after acquisition, the now owning company was slapped with a civil lawsuit. Part of this lawsuit (discovery) is requiring them to retrieve & store from us any related information. Because we were a separate company up until acquisition, there is a high probability that our personal machines might contain information about what the lawsuit alleges (email, documents, chat logs?, etc). Obviously, this depends largely on the person's job function (engineer vs. customer support vs. CEO). All employees are being required to comply. Since acquisition (1.25 yrs), the new company has not provided us with company laptops/desktops. We continue to use personal hardware, licenses, etc for work. Email is via POP3s and not hanging around on the mail server - it's on everyone's client. Documents are spread across personal machines. So, now they want us each to backup our complete personal machines. They are allowing us to create a "personal" folder where we can place personal documents. That single folder will be excluded from backup. Of course, that means total re-arrangement of documents, etc. For most of us, 99% of the data on the machine is NOT related to work. So, what's the consensus? Should we comply? What is their recourse if we do not?

  Read the article

• Windows 7 Icons, Buttons, and Tabs corrupted...Professional 32-bit

  - by xhyperx

  The other day, about two or three ago, I was simply typing in a Microsoft Word document when my screen froze. After a few moments, it went black...I thought it was my vid hardware (dual nVidia 9800 GTs). Anyway, I did a hard reboot, and chose to Start Normally. The system blue screened telling me there was a failure in the Memory Manager. So then I thought maybe a RAM failure or vid memory failure. I attempted reboot again, this time I got presented with the option to repair windows...so I went with that. The repair app finished and did an auto reboot. This time I got all the way back to my desktop where in a matter of a about 30 seconds, the system blue screened again and pointed to the Memory Manager as the area of cause. Again I rebooted, the repair thingy came up again and I allowed it to do its thing. Deciding if the same failure occured I'd begin pulling hardware to see at what point I may have found the possibly defective party. However, this time it rebooted, I got back to desktop and no crash. All looked well, untill I looked at the baloon messages when hovering over the System Bar icons. Also when I opened any of my browsers, the tabs had no text, and any window that pops up that has regular buttons (OK, Cancel, etc., etc.) looks weird. The buttons are really really long and have no text. So it seems like the system is once again running smoothly, however something has gotten corrupted.. something relating to drawing basic windows user interface objects. Help...all ideas are respected and appreciated. Have a great day everyone!

  Read the article

• Ubuntu server 10.04 disconnects after short periods of inactivity on my site

  - by Melot

  Hi! I'm new to Ubuntu (installed it for the first time just a couple of days ago on my server). I've Ubuntu Server 10.04 and am just using the terminal, no GUI like Gnome. So far it's working pretty great except for one big thing. Whenever I go to sleep and there's no activity on my server (it's not a big site so active users drop to 0 during the night), the server kind of disconnects. The only thing that can bring the site back online is to restart the whole server. I've tried disabling powersaving by using setterm but that changes nothing. Even if I wake up the server by pressing any key or so the site wont go back online! I've tried just restarting both Apache and MySQL (I'm using LAMP-server btw) but not even that works. But as soon as I turn the power off and on at the server, everythings work like normal for a couple of minutes of inactivity (~5-15 minutes I'd guess) and then it's down again unless someone logs in to the site and is active. I was previously using XAMPP on my laptop with Windows XP and that worked 24/7 so I don't think it's anything with my router or ISP. This is driving me crazy! My site is down all the time I'm in school as I have no possibility to restart the server if it becomes offline. Does anyone have a clue to what could be wrong?

  Read the article

< Previous Page | 170 171 172 173 174 175 176 177 178 179 180 181  | Next Page >