Search Results

Search found 4542 results on 182 pages for 'idle ide'.

Page 175/182 | < Previous Page | 171 172 173 174 175 176 177 178 179 180 181 182  | Next Page >

• l2tp / ipsec debian Openswan U2.6.38 does not connect

  - by locojay

  i am trying to get ipsec/l2tp running on a debian server with an iphone as a client but always get: Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [RFC 3947] method set to=115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] meth=114, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-08] meth=113, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-07] meth=112, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-06] meth=111, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-05] meth=110, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-04] meth=109, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: ignoring Vendor ID payload [FRAGMENTATION 80000000] Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [Dead Peer Detection] Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: responding to Main Mode from unknown peer <clientip> Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: STATE_MAIN_R1: sent MR1, expecting MI2 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): both are NATed Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: STATE_MAIN_R2: sent MR2, expecting MI3 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: ignoring informational payload, type IPSEC_INITIAL_CONTACT msgid=00000000 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: Main mode peer ID is ID_IPV4_ADDR: '10.2.210.176' Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: switched from "L2TP-PSK-noNAT" to "L2TP-PSK-noNAT" Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: deleting connection "L2TP-PSK-noNAT" instance with peer <clientip> {isakmp=#0/ipsec=#0} Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: new NAT mapping for #20, was <clientip>:43598, now <clientip>:49826 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_256 prf=oakley_sha group=modp1024} Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: Dead Peer Detection (RFC 3706): enabled Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: the peer proposed: <public ip>/32:17/1701 -> 10.2.210.176/32:17/0 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: NAT-Traversal: received 2 NAT-OA. using first, ignoring others Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: responding to Quick Mode proposal {msgid:311d3282} Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: us: 171.138.2.13<171.138.2.13>:17/1701 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: them: <clientip>[10.2.210.176]:17/61719 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: Dead Peer Detection (RFC 3706): enabled Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: transition from state STATE_QUICK_R1 to state STATE_QUICK_R2 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: STATE_QUICK_R2: IPsec SA established transport mode {ESP=>0x05e23c9a <0x216077a9 xfrm=AES_256-HMAC_SHA1 NATOA=10.2.210.176 NATD=<clientip>:49826 DPD=enabled} Dec 2 21:00:26 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received Delete SA(0x05e23c9a) payload: deleting IPSEC State #21 Dec 2 21:00:26 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received and ignored informational message Dec 2 21:00:27 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received Delete SA payload: deleting ISAKMP State #20 Dec 2 21:00:27 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip>: deleting connection "L2TP-PSK-noNAT" instance with peer <clientip> {isakmp=#0/ipsec=#0} Dec 2 21:00:27 vpn pluto[22711]: packet from <clientip>:49826: received and ignored informational message Dec 2 21:00:27 vpn pluto[22711]: ERROR: asynchronous network error report on eth0 (sport=4500) for message to <clientip> port 49826, complainant <clientip>: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] my setup looks like this verizon fios actiontec -- DMZ-- ddwrt router -- debian xen instance actiontec : 192.168.1.1 ddwrt: 171.138.2.1 debian xen server: 171.138.2.13 forwarded udp 500, 4500, 1701 on ddwrt to debian xen instance. vpn passthrough is enabled /etc/ipsec.conf config setup dumpdir=/var/run/pluto/ nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:25.0.0.0/8,%v6:fd00::/8,%v6:fe80::/10,%v4:!171.138.2.0/24,%v4:!192.168.1.0/24 protostack=netkey # Add connections here conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 # we cannot rekey for %any, let client rekey rekey=no # Apple iOS doesn't send delete notify so we need dead peer detection # to detect vanishing clients dpddelay=30 dpdtimeout=120 dpdaction=clear # Set ikelifetime and keylife to same defaults windows has ikelifetime=8h keylife=1h # l2tp-over-ipsec is transport mode type=transport # left=171.138.2.13 # # For updated Windows 2000/XP clients, # to support old clients as well, use leftprotoport=17/%any leftprotoport=17/1701 # # The remote user. # right=%any # Using the magic port of "%any" means "any one single port". This is # a work around required for Apple OSX clients that use a randomly # high port. rightprotoport=17/%any #force all to be nat'ed. because of ios conn passthrough-for-non-l2tp type=passthrough left=171.138.2.13 leftnexthop=171.138.2.1 right=0.0.0.0 rightsubnet=0.0.0.0/0 auto=route /etc/xl2tp/xl2tp.conf [global] ipsec saref = no listen-addr = 171.138.2.13 ;port = 1701 ;debug network = yes ;debug tunnel = yes ;debug network = yes ;debug packet = yes [lns default] ip range = 171.138.2.231-171.138.2.239 local ip = 171.138.2.13 assign ip = yes require chap = no refuse pap = no require authentication = no ;name = OpenswanVPN ppp debug = yes pppoptfile = /etc/ppp/options.xlt2tpd lenght bit = yes /etc/ppp/options.xl2tpd ;require-mschap-v2 pcp-accept-local ipcp-accept-local ipcp-accept-remote ;ms-dns 171.138.2.1 ms-dns 192.168.1.1 ms-dns 8.8.8.8 name l2tpd noccp auth crtscts idle 1800 mtu 1410 mru 1410 lock proxyarp connect-delay 5000 debug dump logfd 2 logfile /var/log/xl2tpd.log ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K3.0.0-1-amd64 (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Two or more interfaces found, checking IP forwarding [FAILED] Checking NAT and MASQUERADEing [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] The failed can be ignored i guess since cat /proc/sys/net/ipv4/ip_forward returns 1 any help would be much appreciated as i don't have any idea why this is not working

  Read the article

• My computer freezes irregularly

  - by Manhim

  My computer started to freeze at irregular times for 3 weeks now. Please note that this question change with each things that i try. (For additional details) What happens My computer freezes, the video stops. (No graphic glitches, it just stops) Sound keeps playing up to some time (Usually 10-30 seconds) then stops playing. Sometimes, randomly, the screen on my G-15 keyboard flickers and I see caracters not at the right places. Usually happens for about 1-2 seconds and a bit before my computer freezes. I have to keep the power button pressed for 4 seconds to shut my computer down. I still hear my hard drives and fans working. Sometimes it works with no problems for a full day, some other times it just keeps freezing each time I restart my computer and I have to leave it for the rest of the day. Sometimes my mouse freezes for a fraction of a second (Like 0.01 to 0.2 seconds) quite randomly, usually before it freezes. No errors spotted by the "Action center" unlike when I had problems with my last video card on this system (Driver errors). My G-15 LCD screen also freezes. Sometimes my G-15 LCD screen flickers and caracters gets caried around temporary under heavy load. Now, most of the times, the BIOS hard disks boot order gets reversed for some reason and I have to put it to the right one and save each times I boot. (Might be unrelated, not sure, but it first started yesterday) Sometimes the BIOS doesn't detect my 750GB hard drive plugged in SATA1. What I did so far I have had similar problems in the past and I had changed my hard drive (It was faulty), so I tested my software RAID-0 array and it was faulty so I changed it. (I reinstalled Windows 7 with this part). I also tested with unplugging my secondary hard drive. My CPU was running at about 100 degree Celsius, I removed the dust between the fans and the heatsink and it's now between 45-55. I ran a CPU stress-test and it didn't freeze during the tests (using Prime95 on all cores) Ran a memory test (using memtest86+) for a single pass and there were no errors. Ran a GPU stress test with ati-tools and furmark and it didn't freeze during the tests. (No artefacts either) I had troubles with my graphic card when I got it, but I think that it got fixed with a driver update. I checked the voltages in my BIOS setup and they all seemed ok (±0.2 I think). I have ran on the computer without problems with Fedora 15 on an external hard drive (Appart that it couldn't load Gnome 3 and was reverting to Gnome 2, didn't want to install drivers since I use it on multiple computers) I used it to backup my files from the raid array to my 1TB hard drive for the reinstallation of Windows. (So the crashes only happenned on Windows) [The external hard drive is plugged directly on a SATA port] I contacted EVGA (My graphic card vendor) and pointed them on this question, I'm looking for an answer. Ran sensors on Fedora 15 and got this output: http://pastebin.com/0BHJnAvu Ran 6 short different CPU stress test on Fedora 15 (Haven't found any complete stress testers for Linux) and it didn't crash. Changed the thermal paste to some Artic Silver 5 for my CPU and stress tested the CPU, temperature was at 50 idle, then 64 highest and slowly went down to 62 during the test. Ran some stress testing with a temporary graphic card and it went ok. Ran furmark stress test with my original graphic card and it freezed again. GPU had a temp of 74C, a CPU temp of 58C and a mobo temp of 40C or 45C (Dunno which one it is from SpeedFan). Ran a furmark stress test and a CPU stress test at the same time, results: http://pastebin.com/2t6PLpdJ I have been using my computer without stressing it for about 2 hours now and no crashes yet. I also have disabled the AMD Cool'n'quiet function on the BIOS for a more regular power to the CPU. When I ran Furmark without C'n'q my computer didn't freeze but I had a "Driver Kernel Error" that have recovered (And Furmark crashed) all that while running a CPU stress test. The computer eventually frozed without me being at it, but this time my screen just went on sleep and I couldn't wake it. Using the stability tester in nTune my computer freezed again (In the same manner as before). I notived that Speedfan gives me a -12V of -16.97V and a -5V of -8.78V. I wonder if these numbers are reliable and if they are good or bad. I have swapped my G-15 with another basic USB keyboard (HP) and I have ran furmark for about 10 minutes with a CPU stability test running each 60 seconds for 30 seconds and my computer haven't crashed yet. Ran some more extended tests without my G-15 and it freezed like it usually do. Removed the nForce Hard disk controler. Disabled command queuing in the NVIDIA nForce SATA Controller for both port 0 and port 1 (Errors from the logs) Used CPUID HwMonitor, here are the voltages: http://pastebin.com/dfM7p4jV Changed some configurations in the motherboard BIOS: Disabled PEG Link Mode, Changed AI Tuning to Standard, Disabled the 1394 Controller, Disabled HD Audio, Disabled JMicron RAID controller and Disabled SATA Raid. When it happens When I play video games (Mostly) When I play flash games (Second most) When I'm looking at my desktop background (It rarely happens when I have a window open, but it does, sometimes) When my Graphic card and my CPU are stressed. Sometimes when my Graphic card is stressed. Never happenned while stressing only the CPU. Sometimes when my CPU is stressed. Specs Windows Seven x64 Home Premium Motherboard: M2N-SLI Deluxe CPU: AMD Phenom 9950 x2 @ 2.6GHz Memory: Kingston 4x2GB Dual Channel (Pretty basic memory sticks) Hard drives: Was 2x250GB (Western digital caviar) in raid-0 + 1TB (WD caviar black), I replaced the raid array with a 750GB (WD caviar black) [Yes I removed the array from the raid configurations] 750W Power supply No overcloking. Ever. There have been some power-downs like 4-5 weeks ago, but the problem didn't start immediately after. (I wasn't home, so my computer got shut-down) Event logs (Warnings, errors and critical errors) for the last 24 hours: http://pastebin.com/Bvvk31T7 My current to-try list Reinstall the drivers and software 1 by 1 and do extensive stress testing between each. Update the BIOS firmware to the most recent stable one. Change my motherboard. Status updates Keeping only the last 3 (28/06 04pm) More stress testing and still pass the tests. (28/06 03pm) Been stress testing for 10 minute straight now and 5 minutes with both CPU and GPU being stressed at the same time. (28/06 03pm) Stress-testing right now, so far no problems. A little hope Tests with Furmark and Prime95. Testing Windows bare-bone: 30 Minutes stress, no freeze. Installing an Anti-virus and some software, restarting computer. Testing with Anti-virus and some software (No drivers installed): 30 Minutes stress, no freeze. Installing audio drivers, restarting computer. Testing with the audio drivers: 30 Minutes stress, no freeze. Installing the latest graphic drivers from EVGA's website (without 3d vision since I don't use it), restarting computer. Testing with the graphic drivers: 30 Minutes stress, no freeze. Configuring Windows to my liking and installing more softwares. In this situation, how can I successfully pin-point the current hardware problem? (If it's a hardware problem) Because I don't really have the budget to just forget and replace everything. I also don't really have hardware to test-replace current hardware.

  Read the article

• Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  - by Mark S. Rasmussen

  As we've been having some problems with sporadic packet loss, I've been preparing a replacement router (also an SSG5) for our current Juniper SSG5. I've setup the new SSG5 identically to the old one. We have a /29 IP range with a single IP setup as a MIP map to a server and two others being used for VIP maps. Each VIP/MIP is accompanied by relevant policies. Long story short - we tried connected the new SSG5 and some things were not working as they should. No problem, I just reconnected the old one. However, some things are still broken, even when I reconnected the old one. I fear I may have inadvertently changed some settings while browsing through old settings in my attempt to reconfigure the new SSG5 unit. All inbound traffic seems to work as expected. However, the 192.168.2.202 server can't initiate any outbound connections. It works perfectly on the local network, but any pings or DNS lookups to external IP's fail. The MIP & VIP map to it works perfectly - I can access it through HTTP and RDP without issues. Any tips on what to debug, or where I've messed up my config? I've attached the full config here (with anonymized IPs): set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin auth timeout 10 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "DMZ" tcp-rst set zone "VLAN" block unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 212.242.193.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 212.242.193.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 212.242.193.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 212.242.193.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname iplan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname nzlan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 212.242.193.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set pak-poll p1queue pak-threshold 96 set pak-poll p2queue pak-threshold 32 set flow tcp-mss unset flow tcp-syn-check set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set ike respond-bad-spi 1 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit traffic set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "HTTP" permit traffic priority 0 set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(212.242.193.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

  Read the article

• Proper network configuration for a KVM guest to be on the same networks at the host

  - by Steve Madsen

  I am running a Debian Linux server on Lenny. Within it, I am running another Lenny instance using KVM. Both servers are externally available, with public IPs, as well as a second interface with private IPs for the LAN. Everything works fine, except the VM sees all network traffic as originating from the host server. I suspect this might have something to do with the iptables-based firewall I'm running on the host. What I'd like to figure out is: how to I properly configure the host's networking such that all of these requirements are met? Both host and VMs have 2 network interfaces (public and private). Both host and VMs can be independently firewalled. Ideally, VM traffic does not have to traverse the host firewall. VMs see real remote IP addresses, not the host's. Currently, the host's network interfaces are configured as bridges. eth0 and eth1 do not have IP addresses assigned to them, but br0 and br1 do. /etc/network/interfaces on the host: # The primary network interface auto br1 iface br1 inet static address 24.123.138.34 netmask 255.255.255.248 network 24.123.138.32 broadcast 24.123.138.39 gateway 24.123.138.33 bridge_ports eth1 bridge_stp off auto br1:0 iface br1:0 inet static address 24.123.138.36 netmask 255.255.255.248 network 24.123.138.32 broadcast 24.123.138.39 # Internal network auto br0 iface br0 inet static address 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 bridge_ports eth0 bridge_stp off This is the libvirt/qemu configuration file for the VM: <domain type='kvm'> <name>apps</name> <uuid>636b6620-0949-bc88-3197-37153b88772e</uuid> <memory>393216</memory> <currentMemory>393216</currentMemory> <vcpu>1</vcpu> <os> <type arch='i686' machine='pc'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='cdrom'> <target dev='hdc' bus='ide'/> <readonly/> </disk> <disk type='file' device='disk'> <source file='/raid/kvm-images/apps.qcow2'/> <target dev='vda' bus='virtio'/> </disk> <interface type='bridge'> <mac address='54:52:00:27:5e:02'/> <source bridge='br0'/> <model type='virtio'/> </interface> <interface type='bridge'> <mac address='54:52:00:40:cc:7f'/> <source bridge='br1'/> <model type='virtio'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target port='0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes' keymap='en-us'/> </devices> </domain> Along with the rest of my firewall rules, the firewalling script includes this command to pass packets destined for a KVM guest: # Allow bridged packets to pass (for KVM guests). iptables -A FORWARD -m physdev --physdev-is-bridged -j ACCEPT (Not applicable to this question, but a side-effect of my bridging configuration appears to be that I can't ever shut down cleanly. The kernel eventually tells me "unregister_netdevice: waiting for br1 to become free" and I have to hard reset the system. Maybe a sign I've done something dumb?)

  Read the article

• Forensic Analysis of the OOM-Killer

  - by Oddthinking

  Ubuntu's Out-Of-Memory Killer wreaked havoc on my server, quietly assassinating my applications, sendmail, apache and others. I've managed to learn what the OOM Killer is, and about its "badness" rules. While my machine is small, my applications are even smaller, and typically only half of my physical memory is in use, let alone swap-space, so I was surprised. I am trying to work out the culprit, but I don't know how to read the OOM-Killer logs. Can anyone please point me to a tutorial on how to read the data in the logs (what are ve, free and gen?), or help me parse these logs? Apr 20 20:03:27 EL135 kernel: kill_signal(13516.0): selecting to kill, queued 0, seq 1, exc 2326 0 goal 2326 0... Apr 20 20:03:27 EL135 kernel: kill_signal(13516.0): task ebb0c6f0, thg d33a1b00, sig 1 Apr 20 20:03:27 EL135 kernel: kill_signal(13516.0): selected 1, signalled 1, queued 1, seq 1, exc 2326 0 red 61795 745 Apr 20 20:03:27 EL135 kernel: kill_signal(13516.0): selecting to kill, queued 0, seq 2, exc 122 0 goal 383 0... Apr 20 20:03:27 EL135 kernel: kill_signal(13516.0): task ebb0c6f0, thg d33a1b00, sig 1 Apr 20 20:03:27 EL135 kernel: kill_signal(13516.0): selected 1, signalled 1, queued 1, seq 2, exc 383 0 red 61795 745 Apr 20 20:03:27 EL135 kernel: kill_signal(13516.0): task ebb0c6f0, thg d33a1b00, sig 2 Apr 20 20:03:27 EL135 kernel: OOM killed process watchdog (pid=14490, ve=13516) exited, free=43104 gen=24501. Apr 20 20:03:27 EL135 kernel: OOM killed process tail (pid=4457, ve=13516) exited, free=43104 gen=24502. Apr 20 20:03:27 EL135 kernel: OOM killed process ntpd (pid=10816, ve=13516) exited, free=43104 gen=24503. Apr 20 20:03:27 EL135 kernel: OOM killed process tail (pid=27401, ve=13516) exited, free=43104 gen=24504. Apr 20 20:03:27 EL135 kernel: OOM killed process tail (pid=29009, ve=13516) exited, free=43104 gen=24505. Apr 20 20:03:27 EL135 kernel: OOM killed process apache2 (pid=10557, ve=13516) exited, free=49552 gen=24506. Apr 20 20:03:27 EL135 kernel: OOM killed process apache2 (pid=24983, ve=13516) exited, free=53117 gen=24507. Apr 20 20:03:27 EL135 kernel: OOM killed process apache2 (pid=29129, ve=13516) exited, free=68493 gen=24508. Apr 20 20:03:27 EL135 kernel: OOM killed process sendmail-mta (pid=941, ve=13516) exited, free=68803 gen=24509. Apr 20 20:03:27 EL135 kernel: OOM killed process tail (pid=12418, ve=13516) exited, free=69330 gen=24510. Apr 20 20:03:27 EL135 kernel: OOM killed process python (pid=22953, ve=13516) exited, free=72275 gen=24511. Apr 20 20:03:27 EL135 kernel: OOM killed process apache2 (pid=6624, ve=13516) exited, free=76398 gen=24512. Apr 20 20:03:27 EL135 kernel: OOM killed process python (pid=23317, ve=13516) exited, free=94285 gen=24513. Apr 20 20:03:27 EL135 kernel: OOM killed process tail (pid=29030, ve=13516) exited, free=95339 gen=24514. Apr 20 20:03:28 EL135 kernel: OOM killed process apache2 (pid=20583, ve=13516) exited, free=101663 gen=24515. Apr 20 20:03:28 EL135 kernel: OOM killed process logger (pid=12894, ve=13516) exited, free=101694 gen=24516. Apr 20 20:03:28 EL135 kernel: OOM killed process bash (pid=21119, ve=13516) exited, free=101849 gen=24517. Apr 20 20:03:28 EL135 kernel: OOM killed process atd (pid=991, ve=13516) exited, free=101880 gen=24518. Apr 20 20:03:28 EL135 kernel: OOM killed process apache2 (pid=14649, ve=13516) exited, free=102748 gen=24519. Apr 20 20:03:28 EL135 kernel: OOM killed process grep (pid=21375, ve=13516) exited, free=132167 gen=24520. Apr 20 20:03:57 EL135 kernel: kill_signal(13516.0): selecting to kill, queued 0, seq 4, exc 4215 0 goal 4826 0... Apr 20 20:03:57 EL135 kernel: kill_signal(13516.0): task ede29370, thg df98b880, sig 1 Apr 20 20:03:57 EL135 kernel: kill_signal(13516.0): selected 1, signalled 1, queued 1, seq 4, exc 4826 0 red 189481 331 Apr 20 20:03:57 EL135 kernel: kill_signal(13516.0): task ede29370, thg df98b880, sig 2 Apr 20 20:04:53 EL135 kernel: kill_signal(13516.0): selecting to kill, queued 0, seq 5, exc 3564 0 goal 3564 0... Apr 20 20:04:53 EL135 kernel: kill_signal(13516.0): task c6c90110, thg cdb1a100, sig 1 Apr 20 20:04:53 EL135 kernel: kill_signal(13516.0): selected 1, signalled 1, queued 1, seq 5, exc 3564 0 red 189481 331 Apr 20 20:04:53 EL135 kernel: kill_signal(13516.0): task c6c90110, thg cdb1a100, sig 2 Apr 20 20:07:14 EL135 kernel: kill_signal(13516.0): selecting to kill, queued 0, seq 6, exc 8071 0 goal 8071 0... Apr 20 20:07:14 EL135 kernel: kill_signal(13516.0): task d7294050, thg c03f42c0, sig 1 Apr 20 20:07:14 EL135 kernel: kill_signal(13516.0): selected 1, signalled 1, queued 1, seq 6, exc 8071 0 red 189481 331 Apr 20 20:07:14 EL135 kernel: kill_signal(13516.0): task d7294050, thg c03f42c0, sig 2 Watchdog is a watchdog task, that was idle; nothing in the logs to suggest it had done anything for days. Its job is to restart one of the applications if it dies, so a bit ironic that it is the first to get killed. Tail was monitoring a few logs files. Unlikely to be consuming memory madly. The apache web-server only serves pages to a little old lady who only uses it to get to church on Sundays a couple of developers who were in bed asleep, and hadn't visited a page on the site for a few weeks. The only traffic it might have had is from the port-scanners; all the content is password-protected and not linked from anywhere, so no spiders are interested. Python is running two separate custom applications. Nothing in the logs to suggest they weren't humming along as normal. One of them was a relatively recent implementation, which makes suspect #1. It doesn't have any data-structures of any significance, and normally uses only about 8% of the total physical RAW. It hasn't misbehaved since. The grep is suspect #2, and the one I want to be guilty, because it was a once-off command. The command (which piped the output of a grep -r to another grep) had been started at least 30 minutes earlier, and the fact it was still running is suspicious. However, I wouldn't have thought grep would ever use a significant amount of memory. It took a while for the OOM killer to get to it, which suggests it wasn't going mad, but the OOM killer stopped once it was killed, suggesting it may have been a memory-hog that finally satisfied the OOM killer's blood-lust.

  Read the article

• Allowing connections initiated from outside

  - by Mark S. Rasmussen

  I've got an old Juniper SSG5 running ScreenOS 5.4.0r6.0. Once a day, more or less, it'll start randomly dropping packets at a rate of ~5-10%. We currently solve this issue by simply rebooting the unit, after which it resumes working in perfect condition. As this error has started appearing randomly, without any configuration or hardware changes, I'm assuming I've got an aging unit about to fail. As such, I've got a replacement SSG5 running ScreenOS 6.0. I've dumped the config on the 5.4 and imported it into a clean 6.0, and it seems to gladly accept it, and all my configuration seems to be A-OK. However, upon connecting the new unit, all outside-initiated connections seem to be blocked. If I browse our external IP from the inside, everything works perfectly, and it's not just port 80, SSH, Crashplan - all of our policies route correctly. All normal networking, initiated from the inside, work perfectly as well. If on the other hand I browse our external IP from the outside, everything is blocked. Barring differences between ScreenOS 5.4 and 6.0, the config is identical. Is there a setting somewhere that defines whether outside/inside initiated connections are allowed? unset key protection enable set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "XXX" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 215.173.182.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 215.173.182.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 215.173.182.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 215.173.182.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname companyalan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname companyblan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 215.173.182.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set pki x509 dn name "[email protected]" set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set vrouter "untrust-vr" exit set vrouter "trust-vr" exit set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "HTTP" permit log set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(215.173.182.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit Note that I've previously posted a similar question (pertaining to the same device & replacement, but ultimately caused by a malfunctioning switch, and thus clouding the current issue): Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  Read the article

• Trouble connecting to vsftpd on ubuntu server

  - by littleK

  I have installed Ubuntu Server 10.10 and I am using it to host a domain that I have. I am trying to set up FTP for the server, but I am running into some problems. I have successfully installed vsFTPd and I have opened up ports 20, 21 on my firewall. In my vsFTPd configuration, I have enabled SSL. Every time I try to connect to my server via FTP, I receive a "Connection Refused" error. I have had a little more success with SSL disabled, however the connection process will time out after the LIST command (but it does accept my authentication). Here is my vsFTPd configuration, the SSL stuff is at the bottom: # Example config file /etc/vsftpd.conf # # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # # Run standalone? vsftpd can run either from an inetd or as a standalone # daemon started from an initscript. listen=YES # # Run standalone with IPv6? # Like the listen parameter, except vsftpd will listen on an IPv6 socket # instead of an IPv4 one. This parameter and the listen parameter are mutually # exclusive. #listen_ipv6=YES # # Allow anonymous FTP? (Disabled by default) anonymous_enable=NO # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) #local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. #anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. #anon_mkdir_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # If enabled, vsftpd will display directory listings with the time # in your local time zone. The default is to display GMT. The # times returned by the MDTM FTP command are also affected by this # option. use_localtime=YES # # Activate logging of uploads/downloads. xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # You may override where the log file goes if you like. The default is shown # below. #xferlog_file=/var/log/vsftpd.log # # If you want, you can have your log file in standard ftpd xferlog format. # Note that the default log file location is /var/log/xferlog in this case. #xferlog_std_format=YES # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # # You may fully customise the login banner string: #ftpd_banner=Welcome to blah FTP service. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd.banned_emails # # You may restrict local users to their home directories. See the FAQ for # the possible risks in this before using chroot_local_user or # chroot_list_enable below. #chroot_local_user=YES # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). #chroot_local_user=YES #chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd.chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. #ls_recurse_enable=YES # # Debian customization # # Some of vsftpd's settings don't fit the Debian filesystem layout by # default. These settings are more Debian-friendly. # # This option should be the name of a directory which is empty. Also, the # directory should not be writable by the ftp user. This directory is used # as a secure chroot() jail at times vsftpd does not require filesystem # access. secure_chroot_dir=/var/run/vsftpd/empty # # This string is the name of the PAM service vsftpd will use. pam_service_name=vsftpd # # This option specifies the location of the RSA certificate to use for SSL # encrypted connections. rsa_cert_file=/etc/ssl/private/vsftpd.pem # SSL ssl_enable=YES allow_anon_ssl=NO force_local_data_ssl=YES force_local_logins_ssl=YES ssl_tlsv1=YES ssl_sslv2=YES ssl_sslv3=YES Thanks!

  Read the article

• Recently "exposed" to Clicksor

  - by I take Drukqs

  Previous information concerning my issue can be found here: Virus...? Tons of people talking. Not sure where else to ask. I heard the loud sounds and whatnot from one of the ads but nothing was harmed and other than having the life scared out of me nothing was immediately affected. Literally nothing has changed. I really don't know what to do. My PC seems fine and from what Malwarebytes and Spybot tells me none of my files have been infected with anything. If you need more information I will be glad to supply it. Thanks in advance. Malwarebytes quick and full scan: Clean. Spybot S&D scan: Clean. HijackThis log: Logfile of Trend Micro HijackThis v2.0.4 Scan saved at 5:23:33 PM, on 2/2/2011 Platform: Windows 7 (WinNT 6.00.3504) MSIE: Internet Explorer v8.00 (8.00.7600.16700) Boot mode: Normal Running processes: C:\Program Files (x86)\DeviceVM\Browser Configuration Utility\BCU.exe C:\Program Files (x86)\NEC Electronics\USB 3.0 Host Controller Driver\Application\nusb3mon.exe C:\Program Files (x86)\Common Files\InstallShield\UpdateService\issch.exe C:\Program Files (x86)\Common Files\Java\Java Update\jusched.exe C:\Program Files (x86)\Pidgin\pidgin.exe C:\Program Files (x86)\Steam\Steam.exe C:\Program Files (x86)\Mozilla Firefox\firefox.exe C:\Program Files (x86)\uTorrent\uTorrent.exe C:\Fraps\fraps.exe C:\Program Files (x86)\Mozilla Firefox\plugin-container.exe C:\Program Files (x86)\Trend Micro\HiJackThis\HiJackThis.exe R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKCU\Software\Microsoft\Internet Explorer\Main,Start Page = http://go.microsoft.com/fwlink/?LinkId=69157 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Page_URL = http://go.microsoft.com/fwlink/?LinkId=69157 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Search_URL = http://go.microsoft.com/fwlink/?LinkId=54896 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKLM\Software\Microsoft\Internet Explorer\Main,Start Page = http://go.microsoft.com/fwlink/?LinkId=69157 R0 - HKLM\Software\Microsoft\Internet Explorer\Search,SearchAssistant = R0 - HKLM\Software\Microsoft\Internet Explorer\Search,CustomizeSearch = R0 - HKLM\Software\Microsoft\Internet Explorer\Main,Local Page = C:\Windows\SysWOW64\blank.htm R0 - HKCU\Software\Microsoft\Internet Explorer\Toolbar,LinksFolderName = R3 - URLSearchHook: SearchHook Class - {BC86E1AB-EDA5-4059-938F-CE307B0C6F0A} - C:\Program Files (x86)\DeviceVM\Browser Configuration Utility\AddressBarSearch.dll F2 - REG:system.ini: UserInit=userinit.exe O2 - BHO: AcroIEHelperStub - {18DF081C-E8AD-4283-A596-FA578C2EBDC3} - C:\Program Files (x86)\Common Files\Adobe\Acrobat\ActiveX\AcroIEHelperShim.dll O2 - BHO: Windows Live ID Sign-in Helper - {9030D464-4C02-4ABF-8ECC-5164760863C6} - C:\Program Files (x86)\Common Files\Microsoft Shared\Windows Live\WindowsLiveLogin.dll O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files (x86)\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [BCU] "C:\Program Files (x86)\DeviceVM\Browser Configuration Utility\BCU.exe" O4 - HKLM\..\Run: [JMB36X IDE Setup] C:\Windows\RaidTool\xInsIDE.exe O4 - HKLM\..\Run: [NUSB3MON] "C:\Program Files (x86)\NEC Electronics\USB 3.0 Host Controller Driver\Application\nusb3mon.exe" O4 - HKLM\..\Run: [ISUSScheduler] "C:\Program Files (x86)\Common Files\InstallShield\UpdateService\issch.exe" -start O4 - HKLM\..\Run: [ISUSPM Startup] C:\PROGRA~2\COMMON~1\INSTAL~1\UPDATE~1\ISUSPM.exe -startup O4 - HKLM\..\Run: [Adobe Reader Speed Launcher] "C:\Program Files (x86)\Adobe\Reader 10.0\Reader\Reader_sl.exe" O4 - HKLM\..\Run: [Adobe ARM] "C:\Program Files (x86)\Common Files\Adobe\ARM\1.0\AdobeARM.exe" O4 - HKLM\..\Run: [SunJavaUpdateSched] "C:\Program Files (x86)\Common Files\Java\Java Update\jusched.exe" O4 - HKLM\..\RunOnce: [Malwarebytes' Anti-Malware] C:\Program Files (x86)\Malwarebytes' Anti-Malware\mbamgui.exe /install /silent O4 - HKCU\..\Run: [ISUSPM Startup] C:\PROGRA~2\COMMON~1\INSTAL~1\UPDATE~1\ISUSPM.exe -startup O4 - HKUS\S-1-5-19\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-19\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-20\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'NETWORK SERVICE') O4 - HKUS\S-1-5-20\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'NETWORK SERVICE') O10 - Unknown file in Winsock LSP: c:\program files (x86)\common files\microsoft shared\windows live\wlidnsp.dll O10 - Unknown file in Winsock LSP: c:\program files (x86)\common files\microsoft shared\windows live\wlidnsp.dll O23 - Service: @%SystemRoot%\system32\Alg.exe,-112 (ALG) - Unknown owner - C:\Windows\System32\alg.exe (file missing) O23 - Service: AppleChargerSrv - Unknown owner - C:\Windows\system32\AppleChargerSrv.exe (file missing) O23 - Service: Browser Configuration Utility Service (BCUService) - DeviceVM, Inc. - C:\Program Files (x86)\DeviceVM\Browser Configuration Utility\BCUService.exe O23 - Service: DES2 Service for Energy Saving. (DES2 Service) - Unknown owner - C:\Program Files (x86)\GIGABYTE\EnergySaver2\des2svr.exe O23 - Service: @%SystemRoot%\system32\efssvc.dll,-100 (EFS) - Unknown owner - C:\Windows\System32\lsass.exe (file missing) O23 - Service: @%systemroot%\system32\fxsresm.dll,-118 (Fax) - Unknown owner - C:\Windows\system32\fxssvc.exe (file missing) O23 - Service: InstallDriver Table Manager (IDriverT) - Macrovision Corporation - C:\Program Files (x86)\Common Files\InstallShield\Driver\11\Intel 32\IDriverT.exe O23 - Service: JMB36X - Unknown owner - C:\Windows\SysWOW64\XSrvSetup.exe O23 - Service: @keyiso.dll,-100 (KeyIso) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @comres.dll,-2797 (MSDTC) - Unknown owner - C:\Windows\System32\msdtc.exe (file missing) O23 - Service: @%SystemRoot%\System32\netlogon.dll,-102 (Netlogon) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: NVIDIA Driver Helper Service (NVSvc) - Unknown owner - C:\Windows\system32\nvvsvc.exe (file missing) O23 - Service: @%systemroot%\system32\psbase.dll,-300 (ProtectedStorage) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @%systemroot%\system32\Locator.exe,-2 (RpcLocator) - Unknown owner - C:\Windows\system32\locator.exe (file missing) O23 - Service: @%SystemRoot%\system32\samsrv.dll,-1 (SamSs) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @%SystemRoot%\system32\snmptrap.exe,-3 (SNMPTRAP) - Unknown owner - C:\Windows\System32\snmptrap.exe (file missing) O23 - Service: @%systemroot%\system32\spoolsv.exe,-1 (Spooler) - Unknown owner - C:\Windows\System32\spoolsv.exe (file missing) O23 - Service: @%SystemRoot%\system32\sppsvc.exe,-101 (sppsvc) - Unknown owner - C:\Windows\system32\sppsvc.exe (file missing) O23 - Service: Steam Client Service - Valve Corporation - C:\Program Files (x86)\Common Files\Steam\SteamService.exe O23 - Service: NVIDIA Stereoscopic 3D Driver Service (Stereo Service) - NVIDIA Corporation - C:\Program Files (x86)\NVIDIA Corporation\3D Vision\nvSCPAPISvr.exe O23 - Service: @%SystemRoot%\system32\ui0detect.exe,-101 (UI0Detect) - Unknown owner - C:\Windows\system32\UI0Detect.exe (file missing) O23 - Service: @%SystemRoot%\system32\vaultsvc.dll,-1003 (VaultSvc) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @%SystemRoot%\system32\vds.exe,-100 (vds) - Unknown owner - C:\Windows\System32\vds.exe (file missing) O23 - Service: @%systemroot%\system32\vssvc.exe,-102 (VSS) - Unknown owner - C:\Windows\system32\vssvc.exe (file missing) O23 - Service: @%SystemRoot%\system32\Wat\WatUX.exe,-601 (WatAdminSvc) - Unknown owner - C:\Windows\system32\Wat\WatAdminSvc.exe (file missing) O23 - Service: @%systemroot%\system32\wbengine.exe,-104 (wbengine) - Unknown owner - C:\Windows\system32\wbengine.exe (file missing) O23 - Service: @%Systemroot%\system32\wbem\wmiapsrv.exe,-110 (wmiApSrv) - Unknown owner - C:\Windows\system32\wbem\WmiApSrv.exe (file missing) O23 - Service: @%PROGRAMFILES%\Windows Media Player\wmpnetwk.exe,-101 (WMPNetworkSvc) - Unknown owner - C:\Program Files (x86)\Windows Media Player\wmpnetwk.exe (file missing) -- End of file - 7889 bytes

  Read the article

• Eclipse Helios on OS X Snow Leopard crashes frequently when editing certain PHP files

  - by William

  I use Eclipse Helios (Eclipse Platform: 3.6.0.I20100608-0911, Eclipse IDE for PHP Developers: 1.3.0.20100617-0520) all the time on OS X (Snow Leopard), and it seems I only run into trouble whenever I'm editing a PHP file that's part of the WordPress blogging framework. When I move my cursor to a variable or function name, that often triggers the beach ball of death. I suspect Eclipse is trying to look up that variable/function and for some reason that causes an endless loop. Sometimes it's not just variables or functions. Just today I was trying to replace all occurrences of a quoted string. Every time I clicked "Replace All", the program would freeze immediately after the string was replaced and the text cursor was moved to the replaced position. I think the moving of the text cursor is important, because I got the same result when I searched for the string (thus moving the cursor), but NOT when I searched for a nonexistent string. I tried disabling everything in my preferences related to marked occurrences, hovering, code assistance, etc. Nothing helps. I use Eclipse for all my projects, and I find that it's only WordPress projects where this happens. Here's my eclipse.ini file: -startup ../../../plugins/org.eclipse.equinox.launcher_1.1.0.v20100507.jar --launcher.library ../../../plugins/org.eclipse.equinox.launcher.cocoa.macosx_1.1.0.v20100503 -product org.eclipse.epp.package.php.product --launcher.defaultAction openFile -showsplash org.eclipse.platform --launcher.XXMaxPermSize 512m --launcher.defaultAction openFile -vmargs -Dosgi.requiredJavaVersion=1.5 -XstartOnFirstThread -Dorg.eclipse.swt.internal.carbon.smallFonts -XX:PermSize=128m -XX:MaxPermSize=128m -XX:MaxGCPauseMillis=10 -XX:MaxHeapFreeRatio=70 -XX:+UseConcMarkSweepGC -XX:+CMSIncrementalMode -XX:+CMSIncrementalPacing -XX:CompileThreshold=5 -Xms128m -Xmx512m -Xss2m -Xdock:icon=../Resources/Eclipse.icns -XstartOnFirstThread -Dorg.eclipse.swt.internal.carbon.smallFonts -framework ../../../plugins/org.eclipse.osgi.services_3.2.100.v20100503.jar I have 4GB of RAM, so I don't know if the problem is I'm underutilizing my resources. Here's what I see over and over in the error log: !ENTRY org.eclipse.jface 2 0 2011-01-16 16:26:21.533 !MESSAGE Keybinding conflicts occurred. They may interfere with normal accelerator operation. !SUBENTRY 1 org.eclipse.jface 2 0 2011-01-16 16:26:21.533 !MESSAGE A conflict occurred for ALT+COMMAND+Q P: Binding(ALT+COMMAND+Q P, ParameterizedCommand(Command(org.eclipse.ui.views.showView,Show View, Shows a particular view, Category(org.eclipse.ui.category.views,Views,Commands for opening views,true), org.eclipse.ui.handlers.ShowViewHandler@2a46d1, [Lorg.eclipse.ui.internal.commands.Parameter;@18f50c2,,true), [Lorg.eclipse.core.commands.Parameterization;@1ff1855), org.eclipse.ui.defaultAcceleratorConfiguration, org.eclipse.ui.contexts.window,,cocoa,system) Binding(ALT+COMMAND+Q P, ParameterizedCommand(Command(org.eclipse.ui.views.showView,Show View, Shows a particular view, Category(org.eclipse.ui.category.views,Views,Commands for opening views,true), org.eclipse.ui.handlers.ShowViewHandler@2a46d1, [Lorg.eclipse.ui.internal.commands.Parameter;@18f50c2,,true), [Lorg.eclipse.core.commands.Parameterization;@96b40c), org.eclipse.ui.defaultAcceleratorConfiguration, org.eclipse.ui.contexts.window,,cocoa,system) !ENTRY org.eclipse.core.net 1 0 2011-01-16 16:26:22.217 !MESSAGE System property http.proxyHost has been set to 127.0.0.1 by an external source. This value will be overwritten using the values from the preferences !ENTRY org.eclipse.core.net 1 0 2011-01-16 16:26:22.217 !MESSAGE System property http.proxyPort has been set to 8888 by an external source. This value will be overwritten using the values from the preferences !ENTRY org.eclipse.core.net 1 0 2011-01-16 16:26:22.218 !MESSAGE System property https.proxyHost has been set to 127.0.0.1 by an external source. This value will be overwritten using the values from the preferences !ENTRY org.eclipse.core.net 1 0 2011-01-16 16:26:22.219 !MESSAGE System property https.proxyPort has been set to 8888 by an external source. This value will be overwritten using the values from the preferences I did some experimenting with the particular script that's giving me trouble. It's a hybrid of HTML and PHP, so Eclipse has to do both HTML and PHP validation. I wondered if the HTML validation had something to do with it, so I created a new file, copied the contents over, and messed with the doctype element. I found that if I replaced the well-formed XHTML 1.0 Strict doctype element with a generic doctype (as such: <!DOCTYPE html>), then I did not crash the program just by moving the cursor around. I set all HTML validation rules to "Ignore", but it still didn't solve my problems. For now, I'm just going to echo the doctype using PHP instead of entering it literally. That seems to prevent crashes. I notice that when I move the cursor around the document, Eclipse displays the "xpath" to my current location at the bottom of the screen. Sometimes there's a delay while it figures out my current path. Perhaps when it's validating against the Strict doctype, it has problems quickly calculating the xpath as I move the cursor around? Maybe it has a stack overflow that causes it to crash.

  Read the article

• How can I get FreeNAS to respond to libvirt shutdown requests

  - by ptomli

  I have a KVM VM of FreeNAS 0.7.1 Shere (revision 5127) running on Ubuntu Server 10.04 and I'm unable to convince the VM to shutdown from the host virsh shutdown freenas I would expect this to send some ACPI? trigger to the VM and FreeNAS then do what it's told. I'm not a FreeBSD fundi so I don't really know what packages or processes to poke to get this running. I have tried to convince powerd to run, but the VM cpus don't have the required freq entry Sysctl HW $ sysctl hw hw.machine: amd64 hw.model: QEMU Virtual CPU version 0.12.3 hw.ncpu: 1 hw.byteorder: 1234 hw.physmem: 523116544 hw.usermem: 463806464 hw.pagesize: 4096 hw.floatingpoint: 1 hw.machine_arch: amd64 hw.realmem: 536850432 hw.aac.iosize_max: 65536 hw.amr.force_sg32: 0 hw.an.an_cache_iponly: 1 hw.an.an_cache_mcastonly: 0 hw.an.an_cache_mode: dbm hw.an.an_dump: off hw.ata.to: 15 hw.ata.wc: 1 hw.ata.atapi_dma: 1 hw.ata.ata_dma_check_80pin: 1 hw.ata.ata_dma: 1 hw.ath.txbuf: 200 hw.ath.rxbuf: 40 hw.ath.regdomain: 0 hw.ath.countrycode: 0 hw.ath.xchanmode: 1 hw.ath.outdoor: 1 hw.ath.calibrate: 30 hw.ath.hal.swba_backoff: 0 hw.ath.hal.sw_brt: 10 hw.ath.hal.dma_brt: 2 hw.bce.msi_enable: 1 hw.bce.tso_enable: 1 hw.bge.allow_asf: 0 hw.cardbus.cis_debug: 0 hw.cardbus.debug: 0 hw.cs.recv_delay: 570 hw.cs.ignore_checksum_failure: 0 hw.cs.debug: 0 hw.cxgb.snd_queue_len: 50 hw.cxgb.use_16k_clusters: 1 hw.cxgb.force_fw_update: 0 hw.cxgb.singleq: 0 hw.cxgb.ofld_disable: 0 hw.cxgb.msi_allowed: 2 hw.cxgb.txq_mr_size: 1024 hw.cxgb.sleep_ticks: 1 hw.cxgb.tx_coalesce: 0 hw.firewire.hold_count: 3 hw.firewire.try_bmr: 1 hw.firewire.fwmem.speed: 2 hw.firewire.fwmem.eui64_lo: 0 hw.firewire.fwmem.eui64_hi: 0 hw.firewire.phydma_enable: 1 hw.firewire.nocyclemaster: 0 hw.firewire.fwe.rx_queue_len: 128 hw.firewire.fwe.tx_speed: 2 hw.firewire.fwe.stream_ch: 1 hw.firewire.fwip.rx_queue_len: 128 hw.firewire.sbp.tags: 0 hw.firewire.sbp.use_doorbell: 0 hw.firewire.sbp.scan_delay: 500 hw.firewire.sbp.login_delay: 1000 hw.firewire.sbp.exclusive_login: 1 hw.firewire.sbp.max_speed: -1 hw.firewire.sbp.auto_login: 1 hw.mfi.max_cmds: 128 hw.mfi.event_class: 0 hw.mfi.event_locale: 65535 hw.pccard.cis_debug: 0 hw.pccard.debug: 0 hw.cbb.debug: 0 hw.cbb.start_32_io: 4096 hw.cbb.start_16_io: 256 hw.cbb.start_memory: 2281701376 hw.pcic.pd6722_vsense: 1 hw.pcic.intr_mask: 57016 hw.pci.honor_msi_blacklist: 1 hw.pci.enable_msix: 1 hw.pci.enable_msi: 1 hw.pci.do_power_resume: 1 hw.pci.do_power_nodriver: 0 hw.pci.enable_io_modes: 1 hw.pci.host_mem_start: 2147483648 hw.syscons.kbd_debug: 1 hw.syscons.kbd_reboot: 1 hw.syscons.bell: 1 hw.syscons.saver.keybonly: 1 hw.syscons.sc_no_suspend_vtswitch: 0 hw.usb.uplcom.interval: 100 hw.usb.uvscom.interval: 100 hw.usb.uvscom.opktsize: 8 hw.wi.debug: 0 hw.wi.txerate: 0 hw.xe.debug: 0 hw.intr_storm_threshold: 1000 hw.availpages: 127714 hw.bus.devctl_disable: 0 hw.ste.rxsyncs: 0 hw.busdma.total_bpages: 32 hw.busdma.zone0.total_bpages: 32 hw.busdma.zone0.free_bpages: 32 hw.busdma.zone0.reserved_bpages: 0 hw.busdma.zone0.active_bpages: 0 hw.busdma.zone0.total_bounced: 0 hw.busdma.zone0.total_deferred: 0 hw.busdma.zone0.lowaddr: 0xffffffff hw.busdma.zone0.alignment: 2 hw.busdma.zone0.boundary: 65536 hw.clockrate: 2808 hw.instruction_sse: 1 hw.apic.enable_extint: 0 hw.kbd.keymap_restrict_change: 0 hw.acpi.supported_sleep_state: S3 S4 S5 hw.acpi.power_button_state: S5 hw.acpi.sleep_button_state: S3 hw.acpi.lid_switch_state: NONE hw.acpi.standby_state: S1 hw.acpi.suspend_state: S3 hw.acpi.sleep_delay: 1 hw.acpi.s4bios: 0 hw.acpi.verbose: 0 hw.acpi.disable_on_reboot: 0 hw.acpi.handle_reboot: 0 hw.acpi.cpu.cx_lowest: C1 Processes $ ps ax PID TT STAT TIME COMMAND 0 ?? DLs 0:00.00 [swapper] 1 ?? ILs 0:00.00 /sbin/init -- 2 ?? DL 0:00.08 [g_event] 3 ?? DL 0:00.29 [g_up] 4 ?? DL 0:00.33 [g_down] 5 ?? DL 0:00.00 [crypto] 6 ?? DL 0:00.00 [crypto returns] 7 ?? DL 0:00.00 [xpt_thrd] 8 ?? DL 0:00.00 [kqueue taskq] 9 ?? DL 0:00.00 [acpi_task_0] 10 ?? RL 34:12.42 [idle: cpu0] 11 ?? WL 0:01.13 [swi4: clock sio] 12 ?? WL 0:00.00 [swi3: vm] 13 ?? WL 0:00.00 [swi1: net] 14 ?? DL 0:00.04 [yarrow] 15 ?? WL 0:00.00 [swi6: task queue] 16 ?? WL 0:00.00 [swi2: cambio] 17 ?? DL 0:00.00 [acpi_task_1] 18 ?? DL 0:00.00 [acpi_task_2] 19 ?? WL 0:00.00 [swi5: +] 20 ?? DL 0:00.01 [thread taskq] 21 ?? WL 0:00.00 [swi6: Giant taskq] 22 ?? WL 0:00.00 [irq9: acpi0] 23 ?? WL 0:00.09 [irq14: ata0] 24 ?? WL 0:00.11 [irq15: ata1] 25 ?? WL 0:00.57 [irq11: ed0 uhci0] 26 ?? DL 0:00.00 [usb0] 27 ?? DL 0:00.00 [usbtask-hc] 28 ?? DL 0:00.00 [usbtask-dr] 29 ?? WL 0:00.01 [irq1: atkbd0] 30 ?? WL 0:00.00 [swi0: sio] 31 ?? DL 0:00.00 [sctp_iterator] 32 ?? DL 0:00.00 [pagedaemon] 33 ?? DL 0:00.00 [vmdaemon] 34 ?? DL 0:00.00 [idlepoll] 35 ?? DL 0:00.00 [pagezero] 36 ?? DL 0:00.01 [bufdaemon] 37 ?? DL 0:00.00 [vnlru] 38 ?? DL 0:00.14 [syncer] 39 ?? DL 0:00.01 [softdepflush] 1221 ?? Is 0:00.00 /sbin/devd 1289 ?? Is 0:00.01 /usr/sbin/syslogd -ss -f /var/etc/syslog.conf 1608 ?? Is 0:00.00 /usr/sbin/cron -s 1692 ?? Ss 0:00.03 /usr/local/sbin/mDNSResponderPosix -b -f /var/etc/mdn 1730 ?? S 0:00.43 /usr/local/sbin/lighttpd -f /var/etc/lighttpd.conf -m 1882 ?? DL 0:00.00 [system_taskq] 1883 ?? DL 0:00.00 [arc_reclaim_thread] 4139 ?? S 0:00.03 /usr/local/bin/php /usr/local/www/exec.php 4144 ?? S 0:00.00 sh -c ps ax 4145 ?? R 0:00.00 ps ax 1816 v0 Is 0:00.01 login [pam] (login) 1818 v0 I+ 0:00.03 -tcsh (csh) 1817 v1 Is+ 0:00.00 /usr/libexec/getty Pc ttyv1 1402 con- I 0:00.00 /usr/local/sbin/afpd -F /var/etc/afpd.conf 1404 con- S 0:00.00 /usr/local/sbin/cnid_metad 1682 con- I 0:02.78 /usr/local/sbin/mt-daapd -m -c /var/etc/mt-daapd.conf 1789 con- S 0:00.18 /usr/local/bin/fuppesd --config-dir /var/etc --config Libvert snippet <domain type='kvm'> <name>freenas</name> <uuid>********-****-****-****-************</uuid> <memory>524288</memory> <currentMemory>524288</currentMemory> <vcpu>1</vcpu> <os> <type arch='x86_64' machine='pc-0.12'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> Is this possible? Ideally I'd like to be able to stop the host without having to manually deal with shutting down the VM.

  Read the article

• Can't Get Virtual Users Setup in VSFTPD -Tried Everything

  - by N.T.

  Have Ubuntu 11.10 with vsftpd installed and working. Can not get virtual users setup at all? Vsftpd will allow main Ubuntu owner account to login, but nothing else? I've followed several tutorials on adding virtual users, but nothing works? I just need to add 2 virtual users and have them be able to upload files to vsftpd Ubuntu computer from other computers on my Lan network. Everywhere I've looked, people just point toward tutorials on adding virtual users, but that just is NOT working. I've been struggling with this for over a week now! PLEASE Help. Thanks. I'll even give a donation if someone can figure this out. here is the vsftpd.conf file I am using. I copied the original, and make a new one, every time I try a tutorial. So far, none have worked. Here is the vsftpd.conf file I'm using. (I hope this helps?) # Example config file /etc/vsftpd.conf # # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # # Run standalone? vsftpd can run either from an inetd or as a standalone # daemon started from an initscript. listen=YES # # Run standalone with IPv6? # Like the listen parameter, except vsftpd will listen on an IPv6 socket # instead of an IPv4 one. This parameter and the listen parameter are mutually # exclusive. #listen_ipv6=YES # # Allow anonymous FTP? (Disabled by default) anonymous_enable=YES # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. #anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. anon_mkdir_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # If enabled, vsftpd will display directory listings with the time # in your local time zone. The default is to display GMT. The # times returned by the MDTM FTP command are also affected by this # option. use_localtime=YES # # Activate logging of uploads/downloads. xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # You may override where the log file goes if you like. The default is shown # below. #xferlog_file=/var/log/vsftpd.log # # If you want, you can have your log file in standard ftpd xferlog format. # Note that the default log file location is /var/log/xferlog in this case. xferlog_std_format=YES # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # # You may fully customise the login banner string: ftpd_banner=Welcome to Sage FTP service. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd.banned_emails # # You may restrict local users to their home directories. See the FAQ for # the possible risks in this before using chroot_local_user or # chroot_list_enable below. chroot_local_user=YES # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). #chroot_local_user=YES #chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd.chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. #ls_recurse_enable=YES # # Debian customization # # Some of vsftpd's settings don't fit the Debian filesystem layout by # default. These settings are more Debian-friendly. # # This option should be the name of a directory which is empty. Also, the # directory should not be writable by the ftp user. This directory is used # as a secure chroot() jail at times vsftpd does not require filesystem # access. secure_chroot_dir=/var/run/vsftpd/empty # # This string is the name of the PAM service vsftpd will use. pam_service_name=vsftpd local_root=/media/FilesDrive # # This option specifies the location of the RSA certificate to use for SSL # encrypted connections. rsa_cert_file=/etc/ssl/private/vsftpd.pem

  Read the article

• Strange Recurrent Excessive I/O Wait

  - by Chris

  I know quite well that I/O wait has been discussed multiple times on this site, but all the other topics seem to cover constant I/O latency, while the I/O problem we need to solve on our server occurs at irregular (short) intervals, but is ever-present with massive spikes of up to 20k ms a-wait and service times of 2 seconds. The disk affected is /dev/sdb (Seagate Barracuda, for details see below). A typical iostat -x output would at times look like this, which is an extreme sample but by no means rare: iostat (Oct 6, 2013) tps rd_sec/s wr_sec/s avgrq-sz avgqu-sz await svctm %util 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 16.00 0.00 156.00 9.75 21.89 288.12 36.00 57.60 5.50 0.00 44.00 8.00 48.79 2194.18 181.82 100.00 2.00 0.00 16.00 8.00 46.49 3397.00 500.00 100.00 4.50 0.00 40.00 8.89 43.73 5581.78 222.22 100.00 14.50 0.00 148.00 10.21 13.76 5909.24 68.97 100.00 1.50 0.00 12.00 8.00 8.57 7150.67 666.67 100.00 0.50 0.00 4.00 8.00 6.31 10168.00 2000.00 100.00 2.00 0.00 16.00 8.00 5.27 11001.00 500.00 100.00 0.50 0.00 4.00 8.00 2.96 17080.00 2000.00 100.00 34.00 0.00 1324.00 9.88 1.32 137.84 4.45 59.60 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 22.00 44.00 204.00 11.27 0.01 0.27 0.27 0.60 Let me provide you with some more information regarding the hardware. It's a Dell 1950 III box with Debian as OS where uname -a reports the following: Linux xx 2.6.32-5-amd64 #1 SMP Fri Feb 15 15:39:52 UTC 2013 x86_64 GNU/Linux The machine is a dedicated server that hosts an online game without any databases or I/O heavy applications running. The core application consumes about 0.8 of the 8 GBytes RAM, and the average CPU load is relatively low. The game itself, however, reacts rather sensitive towards I/O latency and thus our players experience massive ingame lag, which we would like to address as soon as possible. iostat: avg-cpu: %user %nice %system %iowait %steal %idle 1.77 0.01 1.05 1.59 0.00 95.58 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sdb 13.16 25.42 135.12 504701011 2682640656 sda 1.52 0.74 20.63 14644533 409684488 Uptime is: 19:26:26 up 229 days, 17:26, 4 users, load average: 0.36, 0.37, 0.32 Harddisk controller: 01:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 1078 (rev 04) Harddisks: Array 1, RAID-1, 2x Seagate Cheetah 15K.5 73 GB SAS Array 2, RAID-1, 2x Seagate ST3500620SS Barracuda ES.2 500GB 16MB 7200RPM SAS Partition information from df: Filesystem 1K-blocks Used Available Use% Mounted on /dev/sdb1 480191156 30715200 425083668 7% /home /dev/sda2 7692908 437436 6864692 6% / /dev/sda5 15377820 1398916 13197748 10% /usr /dev/sda6 39159724 19158340 18012140 52% /var Some more data samples generated with iostat -dx sdb 1 (Oct 11, 2013) Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sdb 0.00 15.00 0.00 70.00 0.00 656.00 9.37 4.50 1.83 4.80 33.60 sdb 0.00 0.00 0.00 2.00 0.00 16.00 8.00 12.00 836.00 500.00 100.00 sdb 0.00 0.00 0.00 3.00 0.00 32.00 10.67 9.96 1990.67 333.33 100.00 sdb 0.00 0.00 0.00 4.00 0.00 40.00 10.00 6.96 3075.00 250.00 100.00 sdb 0.00 0.00 0.00 0.00 0.00 0.00 0.00 4.00 0.00 0.00 100.00 sdb 0.00 0.00 0.00 2.00 0.00 16.00 8.00 2.62 4648.00 500.00 100.00 sdb 0.00 0.00 0.00 0.00 0.00 0.00 0.00 2.00 0.00 0.00 100.00 sdb 0.00 0.00 0.00 1.00 0.00 16.00 16.00 1.69 7024.00 1000.00 100.00 sdb 0.00 74.00 0.00 124.00 0.00 1584.00 12.77 1.09 67.94 6.94 86.00 Characteristic charts generated with rrdtool can be found here: iostat plot 1, 24 min interval: http://imageshack.us/photo/my-images/600/yqm3.png/ iostat plot 2, 120 min interval: http://imageshack.us/photo/my-images/407/griw.png/ As we have a rather large cache of 5.5 GBytes, we thought it might be a good idea to test if the I/O wait spikes would perhaps be caused by cache miss events. Therefore, we did a sync and then this to flush the cache and buffers: echo 3 > /proc/sys/vm/drop_caches and directly afterwards the I/O wait and service times virtually went through the roof, and everything on the machine felt like slow motion. During the next few hours the latency recovered and everything was as before - small to medium lags in short, unpredictable intervals. Now my question is: does anybody have any idea what might cause this annoying behaviour? Is it the first indication of the disk array or the raid controller dying, or something that can be easily mended by rebooting? (At the moment we're very reluctant to do this, however, because we're afraid that the disks might not come back up again.) Any help is greatly appreciated. Thanks in advance, Chris. Edited to add: we do see one or two processes go to 'D' state in top, one of which seems to be kjournald rather frequently. If I'm not mistaken, however, this does not indicate the processes causing the latency, but rather those affected by it - correct me if I'm wrong. Does the information about uninterruptibly sleeping processes help us in any way to address the problem? @Andy Shinn requested smartctl data, here it is: smartctl -a -d megaraid,2 /dev/sdb yields: smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Device: SEAGATE ST3500620SS Version: MS05 Serial number: Device type: disk Transport protocol: SAS Local Time is: Mon Oct 14 20:37:13 2013 CEST Device supports SMART and is Enabled Temperature Warning Disabled or Not Supported SMART Health Status: OK Current Drive Temperature: 20 C Drive Trip Temperature: 68 C Elements in grown defect list: 0 Vendor (Seagate) cache information Blocks sent to initiator = 1236631092 Blocks received from initiator = 1097862364 Blocks read from cache and sent to initiator = 1383620256 Number of read and write commands whose size <= segment size = 531295338 Number of read and write commands whose size > segment size = 51986460 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36556.93 number of minutes until next internal SMART test = 32 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 509271032 47 0 509271079 509271079 20981.423 0 write: 0 0 0 0 0 5022.039 0 verify: 1870931090 196 0 1870931286 1870931286 100558.708 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 16 36538 - [- - -] # 2 Background short Completed 16 36514 - [- - -] # 3 Background short Completed 16 36490 - [- - -] # 4 Background short Completed 16 36466 - [- - -] # 5 Background short Completed 16 36442 - [- - -] # 6 Background long Completed 16 36420 - [- - -] # 7 Background short Completed 16 36394 - [- - -] # 8 Background short Completed 16 36370 - [- - -] # 9 Background long Completed 16 36364 - [- - -] #10 Background short Completed 16 36361 - [- - -] #11 Background long Completed 16 2 - [- - -] #12 Background short Completed 16 0 - [- - -] Long (extended) Self Test duration: 6798 seconds [113.3 minutes] smartctl -a -d megaraid,3 /dev/sdb yields: smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Device: SEAGATE ST3500620SS Version: MS05 Serial number: Device type: disk Transport protocol: SAS Local Time is: Mon Oct 14 20:37:26 2013 CEST Device supports SMART and is Enabled Temperature Warning Disabled or Not Supported SMART Health Status: OK Current Drive Temperature: 19 C Drive Trip Temperature: 68 C Elements in grown defect list: 0 Vendor (Seagate) cache information Blocks sent to initiator = 288745640 Blocks received from initiator = 1097848399 Blocks read from cache and sent to initiator = 1304149705 Number of read and write commands whose size <= segment size = 527414694 Number of read and write commands whose size > segment size = 51986460 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36596.83 number of minutes until next internal SMART test = 28 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 610862490 44 0 610862534 610862534 20470.133 0 write: 0 0 0 0 0 5022.480 0 verify: 2861227413 203 0 2861227616 2861227616 100872.443 0 Non-medium error count: 1 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 16 36580 - [- - -] # 2 Background short Completed 16 36556 - [- - -] # 3 Background short Completed 16 36532 - [- - -] # 4 Background short Completed 16 36508 - [- - -] # 5 Background short Completed 16 36484 - [- - -] # 6 Background long Completed 16 36462 - [- - -] # 7 Background short Completed 16 36436 - [- - -] # 8 Background short Completed 16 36412 - [- - -] # 9 Background long Completed 16 36404 - [- - -] #10 Background short Completed 16 36401 - [- - -] #11 Background long Completed 16 2 - [- - -] #12 Background short Completed 16 0 - [- - -] Long (extended) Self Test duration: 6798 seconds [113.3 minutes]

  Read the article

• How can I resolve this one application coming up with an "You don't have permission to use the application" error?

  - by morgant

  I've got a Mac OS X 10.6 Snow Leopard Server Open Directory Master with a user who's getting Mobility & Application managed preferences from a group (the only group they're a member of). The workstation is also running Mac OS X 10.6 Snow Leopard, when the user logs in and tries to run our primary application which they're explicitly allowed to run (via the group's preferences), it says "You don't have permission to use the application 'Blah'". Now, the application is added to the group's list of always allowed applications, unsigned (so a minor difference in application version or file contents shouldn't disallow it). It even lives in a subdirectory of /Applications which is in the list of folders to allow applications. I've run into this when logging this user into new workstations and the following usually works: Log them out Remove the following files from their mobile home folder on the workstation: /Library/Managed\ Preferences/, ~/.FileSync, ~/Library/Preferences/com.apple.finder.plist, and ~/Library/Preferences/com.apple.MCX.plist. Remove the following files from their network home folder on the server: ~/.FileSync, ~/Library/Preferences/com.apple.finder.plist, and ~/Library/Preferences/com.apple.MCX.plist. Log them back in on the workstation. However, this no longer resolves the issue. Their Home Sync preferences are set (on the group) to sync ~, but not the following files (manually, at login, and at logout... no background sync here): ~/.SymAVQSFile ~/NAVMac800QSFile ~/Library ~/.FileSync ~/.account Their Preferences Sync preferences are set (also on the group) to sync ~/Library & ~/Documents/Microsoft User Data, but not the following files (also manually, at login, and at logout... no background sync): ~/.SymAVQSFile ~/.Trash ~/.Trashes ~/Documents/Microsoft User Data/Entourage Temp ~/Library/Application Support/SyncServices ~/Library/Application Support/MobileSync ~/Library/Caches ~/Library/Calendars/Calendar Cache ~/Library/Logs ~/Library/Mail/AvailableFeeds ~/Library/Mail/Envelope Index ~/Library/Preferences/Macromedia/ ~/Library/Printers ~/Library/PubSub/Database ~/Library/PubSub/Downloads ~/Library/PubSub/Feeds ~/Library/Safari/Icons.db ~/Library/Safari/HistoryIndex.sk ~/Library/iTunes/iPhone Software Updates IMAP-* Exchange-* EWS-* Mac-* ~/Library/Preferences/ByHost ~/Library/Preferences/com.apple.dock.plist ~/Library/Preferences/com.apple.sitebarlists.plist ~/Library/Application Support/4D ~/Library/Preferences/com.apple.MCX.plist ~/.FileSync ~/.account Even with ~/Library/Preferences/com.apple.MCX.plist prevented from syncing during a Preferences Sync, it still seems to show up in the network home on the server frequently. Are there any other files other than ~/Library/Preferences/com.apple.MCX.plist that contain application Managed Preferences that might be causing this one app to be showing up as not allowed? Any ideas on how ~/Library/Preferences/com.apple.MCX.plist keeps getting sync'd back up the network home folder on the server? Update: I thought I had found a workaround this morning, but it also seemed to be extremely temporary. Basically, loking at /Library/Managed\ Preferences/[shortname]/com.apple.applicationaccess.new.plist I discovered that it didn't have an entry for the application in question, but /Library/Managed\ Preferences/[shortname]/complete.plist did. Naturally, I deleted com.apple.applicationaccess.new.plist, logged in again, and it worked... on one workstation. It failed on others, and after logging out & back in a couple more times it started failing on all of them again, even after further deletions of com.apple.applicationaccess.new.plist. Oddly, com.apple.applicationaccess.new.plist & complete.plist do both contain an entry for the application in question now, but it still says it's not allowed. Further Update: Okay, so I now have a reproducible workaround which seems to be required after every reboot of the workstation: Log in as the user (you'll discover you cannot launch the application in question). Fast User Switch to the local admin account on the workstation (we always have one on every machine). From that local admin account, run sudo mcxrefresh -n 'shortname' (logging out and back in as the user in question will not work). Fast User Switch back to the user (you'll still not be allowed to run the application). Log the user out and back in (you'll now be able to run the application in question.) Fast User Switch back to the local admin account, log it out, and log back in as the user in question. If you do all that exactly as described it'll keep working through log out & log back in, but NOT through a reboot. If, after a reboot, you try something like logging in as the local admin account, running sudo mcxrefresh -n 'shortname', logging out, then logging in as the user in question, it will NOT work. Yet Another Update We don't have any computer groups in our Open Directory, so it shouldn't be getting any conflicting settings from there. I ran sudo mcxquery -format xml -user shortname -group groupname before & after performing the aforementioned process to allow the application in question to be run and the results were identical (saved the result to files & diff'd... I'm not just guessing here). One Step Forward, Half a Step Back: When the Mac OS X 10.6.5 Server update was released, we upgraded our Open Directory Master to it as the changes included the following managed preferences fixes which I hoped might address this issue: Addresses an issue that could prevent managed preferences from being applied when a user logs in on a workstation that has been idle. Fixes an issue that could prevent administrators from bypassing client management settings on a workstation. This seemed to improve the situation slightly. The application in question now usually launches without error. If, and when it does launch with the "You don't have permission to use the application" error, logging the user out and back in seems to correct it. That said, we've since had to add a couple of applications to the user's ~/Applications/ directory and those are still prevented from launching. The workstations are running Mac OS X 10.6.4, the OD Master (which the workstations are bound to) is running Mac OS 10.6.5 Server (although there are two OD Replicas still running 10.6.4 Server), and we're using Workgroup Manager 10.6.3 (which is included with the Server Admin Tools 10.6.5 upgrade) to add the applications (unsigned, as always). This time, I've caught the following in /var/log/system.log when attempting to launch one of the allowed applications from ~/Applications: Dec 22 17:36:24 hostname parentalcontrolsd[43221]: -[ActivityTracker checkApp:csFlags:] [954:username] -- *** Incoming app appears to be masquerading as white listed app and failed signature validation: /Users/username/Applications/FileMaker Pro 5.5/FileMaker Pro.app/Contents/MacOS/FileMaker Pro. Note: This may be a valid app of a different version than what was whitelisted (on a different volume?) Dec 22 17:36:24 hostname [0x0-0xa42a42].com.filemaker.filemakerpro[43304]: launch of /Users/username/Applications/FileMaker Pro 5.5/FileMaker Pro.app/Contents/MacOS/FileMaker Pro was blocked Dec 22 17:36:24 hostname com.apple.launchd.peruser.1340[6375] ([0x0-0xa42a42].com.filemaker.filemakerpro[43304]): Exited with exit code: 255 Dec 22 17:36:24 hostname parentalcontrolsd[43221]: -[ActivityTracker(Private) _removeAppFromWhiteList:] [1362:username] -- *** Couldn't find local user record Running sudo mcxquery -format xml -user username -group groupname includes the following entry for FileMaker Pro 5.5 (and appears to include a full integration of the user's application whitelist & group's application whitelist): <dict> <key>bundleID</key> <string>com.filemaker.filemakerpro</string> <key>displayName</key> <string>FileMaker Pro</string> </dict> Note the lack of <key>appID</key><data> ... </data> which seems to specify a signed application. While whitelisted directories also appear to be correctly listed in the results, they too do not actually allow the applications to be run either. What is going on here?! Where else should I be looking?

  Read the article

• More interruptions than cpu context switches

  - by Christopher Valles

  I have a machine running Debian GNU/Linux 5.0.8 (lenny) 8 cores and 12Gb of RAM. We have one core permanently around 40% ~ 60% wait time and trying to spot what is happening I realized that we have more interruptions than cpu context switches. I found that the normal ratio between context switch and interruptions is around 10x more context switching than interruptions but on my server the values are completely different. backend1:~# vmstat -s 12330788 K total memory 12221676 K used memory 3668624 K active memory 6121724 K inactive memory 109112 K free memory 3929400 K buffer memory 4095536 K swap cache 4194296 K total swap 7988 K used swap 4186308 K free swap 44547459 non-nice user cpu ticks 702408 nice user cpu ticks 13346333 system cpu ticks 1607583668 idle cpu ticks 374043393 IO-wait cpu ticks 4144149 IRQ cpu ticks 3994255 softirq cpu ticks 0 stolen cpu ticks 4445557114 pages paged in 2910596714 pages paged out 128642 pages swapped in 267400 pages swapped out 3519307319 interrupts 2464686911 CPU context switches 1306744317 boot time 11555115 forks Any ideas if that is an issue? And in that case, how can I spot the cause and fix it? Update Following the instructions of the comments and focusing on the core stuck in wait I checked the processes attached to that core and below you can find the list: PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ P COMMAND 24 root RT -5 0 0 0 S 0 0.0 0:03.42 7 migration/7 25 root 15 -5 0 0 0 S 0 0.0 0:04.78 7 ksoftirqd/7 26 root RT -5 0 0 0 S 0 0.0 0:00.00 7 watchdog/7 34 root 15 -5 0 0 0 S 0 0.0 1:18.90 7 events/7 83 root 15 -5 0 0 0 S 0 0.0 1:10.68 7 kblockd/7 291 root 15 -5 0 0 0 S 0 0.0 0:00.00 7 aio/7 569 root 15 -5 0 0 0 S 0 0.0 0:00.00 7 ata/7 1545 root 15 -5 0 0 0 S 0 0.0 0:00.00 7 ksnapd 1644 root 15 -5 0 0 0 S 0 0.0 0:36.73 7 kjournald 1725 root 16 -4 16940 1152 488 S 0 0.0 0:00.00 7 udevd 2342 root 20 0 8828 1140 956 S 0 0.0 0:00.00 7 sh 2375 root 20 0 8848 1220 1016 S 0 0.0 0:00.00 7 locate 2421 root 30 10 8896 1268 1016 S 0 0.0 0:00.00 7 updatedb.findut 2430 root 30 10 58272 49m 616 S 0 0.4 0:17.44 7 sort 2431 root 30 10 3792 448 360 S 0 0.0 0:00.00 7 frcode 2682 root 15 -5 0 0 0 S 0 0.0 3:25.98 7 kjournald 2683 root 15 -5 0 0 0 S 0 0.0 0:00.64 7 kjournald 2687 root 15 -5 0 0 0 S 0 0.0 1:31.30 7 kjournald 3261 root 15 -5 0 0 0 S 0 0.0 2:30.56 7 kondemand/7 3364 root 20 0 3796 596 476 S 0 0.0 0:00.00 7 acpid 3575 root 20 0 8828 1140 956 S 0 0.0 0:00.00 7 sh 3597 root 20 0 8848 1216 1016 S 0 0.0 0:00.00 7 locate 3603 root 30 10 8896 1268 1016 S 0 0.0 0:00.00 7 updatedb.findut 3612 root 30 10 58272 49m 616 S 0 0.4 0:27.04 7 sort 3655 root 20 0 11056 2852 516 S 0 0.0 5:36.46 7 redis-server 3706 root 20 0 19832 1056 816 S 0 0.0 0:01.64 7 cron 3746 root 20 0 3796 580 484 S 0 0.0 0:00.00 7 getty 3748 root 20 0 3796 580 484 S 0 0.0 0:00.00 7 getty 7674 root 20 0 28376 1000 736 S 0 0.0 0:00.00 7 cron 7675 root 20 0 8828 1140 956 S 0 0.0 0:00.00 7 sh 7708 root 30 10 58272 49m 616 S 0 0.4 0:03.36 7 sort 22049 root 20 0 8828 1136 956 S 0 0.0 0:00.00 7 sh 22095 root 20 0 8848 1220 1016 S 0 0.0 0:00.00 7 locate 22099 root 30 10 8896 1264 1016 S 0 0.0 0:00.00 7 updatedb.findut 22108 root 30 10 58272 49m 616 S 0 0.4 0:44.55 7 sort 22109 root 30 10 3792 452 360 S 0 0.0 0:00.00 7 frcode 26927 root 20 0 8828 1140 956 S 0 0.0 0:00.00 7 sh 26947 root 20 0 8848 1216 1016 S 0 0.0 0:00.00 7 locate 26951 root 30 10 8896 1268 1016 S 0 0.0 0:00.00 7 updatedb.findut 26960 root 30 10 58272 49m 616 S 0 0.4 0:10.24 7 sort 26961 root 30 10 3792 452 360 S 0 0.0 0:00.00 7 frcode 27952 root 20 0 65948 3028 2400 S 0 0.0 0:00.00 7 sshd 30731 root 20 0 0 0 0 S 0 0.0 0:01.34 7 pdflush 31204 root 20 0 0 0 0 S 0 0.0 0:00.24 7 pdflush 21857 deploy 20 0 1227m 2240 868 S 0 0.0 2:44.22 7 nginx 21858 deploy 20 0 1228m 2784 868 S 0 0.0 2:42.45 7 nginx 21862 deploy 20 0 1228m 2732 868 S 0 0.0 2:43.90 7 nginx 21869 deploy 20 0 1228m 2840 868 S 0 0.0 2:44.14 7 nginx 27994 deploy 20 0 19372 2216 1380 S 0 0.0 0:00.00 7 bash 28493 deploy 20 0 331m 32m 16m S 4 0.3 0:00.40 7 apache2 21856 deploy 20 0 1228m 2844 868 S 0 0.0 2:43.64 7 nginx 3622 nobody 30 10 21156 10m 916 D 0 0.1 4:42.31 7 find 7716 nobody 30 10 12268 1280 888 D 0 0.0 0:43.50 7 find 22116 nobody 30 10 12612 1696 916 D 0 0.0 6:32.26 7 find 26968 nobody 30 10 12268 1284 888 D 0 0.0 1:56.92 7 find Update As suggested I take a look at /proc/interrupts and below the info there: CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7 0: 35 0 0 1469085485 0 0 0 0 IO-APIC-edge timer 1: 0 0 0 8 0 0 0 0 IO-APIC-edge i8042 8: 0 0 0 1 0 0 0 0 IO-APIC-edge rtc0 9: 0 0 0 0 0 0 0 0 IO-APIC-fasteoi acpi 12: 0 0 0 105 0 0 0 0 IO-APIC-edge i8042 16: 0 0 0 0 0 0 0 580212114 IO-APIC-fasteoi 3w-9xxx, uhci_hcd:usb1 18: 0 0 142 0 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb6, ehci_hcd:usb7 19: 9 0 0 0 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb3, uhci_hcd:usb5 21: 0 0 0 0 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb2 23: 0 0 0 0 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb4, ehci_hcd:usb8 1273: 0 0 1600400502 0 0 0 0 0 PCI-MSI-edge eth0 1274: 0 0 0 0 0 0 0 0 PCI-MSI-edge ahci NMI: 0 0 0 0 0 0 0 0 Non-maskable interrupts LOC: 214252181 69439018 317298553 21943690 72562482 56448835 137923978 407514738 Local timer interrupts RES: 27516446 16935944 26430972 44957009 24935543 19881887 57746906 24298747 Rescheduling interrupts CAL: 10655 10705 10685 10567 10689 10669 10667 396 function call interrupts TLB: 529548 462587 801138 596193 922202 747313 2027966 946594 TLB shootdowns TRM: 0 0 0 0 0 0 0 0 Thermal event interrupts THR: 0 0 0 0 0 0 0 0 Threshold APIC interrupts SPU: 0 0 0 0 0 0 0 0 Spurious interrupts ERR: 0 All the values seems more or less the same for all the cores but this one IO-APIC-fasteoi 3w-9xxx, uhci_hcd:usb1 only affects to the core 7 (the same with the wait time of 40% ~ 60%) could be something attached to the usb port causing the issue? Thanks in advanced

  Read the article

• How can I resolve this one application coming up with an "You don't have permission to use the application" error?

  - by morgant

  I've got a Mac OS X 10.6 Snow Leopard Server Open Directory Master with a user who's getting Mobility & Application managed preferences from a group (the only group they're a member of). The workstation is also running Mac OS X 10.6 Snow Leopard, when the user logs in and tries to run our primary application which they're explicitly allowed to run (via the group's preferences), it says "You don't have permission to use the application 'Blah'". Now, the application is added to the group's list of always allowed applications, unsigned (so a minor difference in application version or file contents shouldn't disallow it). It even lives in a subdirectory of /Applications which is in the list of folders to allow applications. I've run into this when logging this user into new workstations and the following usually works: Log them out Remove the following files from their mobile home folder on the workstation: /Library/Managed\ Preferences/, ~/.FileSync, ~/Library/Preferences/com.apple.finder.plist, and ~/Library/Preferences/com.apple.MCX.plist. Remove the following files from their network home folder on the server: ~/.FileSync, ~/Library/Preferences/com.apple.finder.plist, and ~/Library/Preferences/com.apple.MCX.plist. Log them back in on the workstation. However, this no longer resolves the issue. Their Home Sync preferences are set (on the group) to sync ~, but not the following files (manually, at login, and at logout... no background sync here): ~/.SymAVQSFile ~/NAVMac800QSFile ~/Library ~/.FileSync ~/.account Their Preferences Sync preferences are set (also on the group) to sync ~/Library & ~/Documents/Microsoft User Data, but not the following files (also manually, at login, and at logout... no background sync): ~/.SymAVQSFile ~/.Trash ~/.Trashes ~/Documents/Microsoft User Data/Entourage Temp ~/Library/Application Support/SyncServices ~/Library/Application Support/MobileSync ~/Library/Caches ~/Library/Calendars/Calendar Cache ~/Library/Logs ~/Library/Mail/AvailableFeeds ~/Library/Mail/Envelope Index ~/Library/Preferences/Macromedia/ ~/Library/Printers ~/Library/PubSub/Database ~/Library/PubSub/Downloads ~/Library/PubSub/Feeds ~/Library/Safari/Icons.db ~/Library/Safari/HistoryIndex.sk ~/Library/iTunes/iPhone Software Updates IMAP-* Exchange-* EWS-* Mac-* ~/Library/Preferences/ByHost ~/Library/Preferences/com.apple.dock.plist ~/Library/Preferences/com.apple.sitebarlists.plist ~/Library/Application Support/4D ~/Library/Preferences/com.apple.MCX.plist ~/.FileSync ~/.account Even with ~/Library/Preferences/com.apple.MCX.plist prevented from syncing during a Preferences Sync, it still seems to show up in the network home on the server frequently. Are there any other files other than ~/Library/Preferences/com.apple.MCX.plist that contain application Managed Preferences that might be causing this one app to be showing up as not allowed? Any ideas on how ~/Library/Preferences/com.apple.MCX.plist keeps getting sync'd back up the network home folder on the server? Update: I thought I had found a workaround this morning, but it also seemed to be extremely temporary. Basically, loking at /Library/Managed\ Preferences/[shortname]/com.apple.applicationaccess.new.plist I discovered that it didn't have an entry for the application in question, but /Library/Managed\ Preferences/[shortname]/complete.plist did. Naturally, I deleted com.apple.applicationaccess.new.plist, logged in again, and it worked... on one workstation. It failed on others, and after logging out & back in a couple more times it started failing on all of them again, even after further deletions of com.apple.applicationaccess.new.plist. Oddly, com.apple.applicationaccess.new.plist & complete.plist do both contain an entry for the application in question now, but it still says it's not allowed. Further Update: Okay, so I now have a reproducible workaround which seems to be required after every reboot of the workstation: Log in as the user (you'll discover you cannot launch the application in question). Fast User Switch to the local admin account on the workstation (we always have one on every machine). From that local admin account, run sudo mcxrefresh -n 'shortname' (logging out and back in as the user in question will not work). Fast User Switch back to the user (you'll still not be allowed to run the application). Log the user out and back in (you'll now be able to run the application in question.) Fast User Switch back to the local admin account, log it out, and log back in as the user in question. If you do all that exactly as described it'll keep working through log out & log back in, but NOT through a reboot. If, after a reboot, you try something like logging in as the local admin account, running sudo mcxrefresh -n 'shortname', logging out, then logging in as the user in question, it will NOT work. Yet Another Update We don't have any computer groups in our Open Directory, so it shouldn't be getting any conflicting settings from there. I ran sudo mcxquery -format xml -user shortname -group groupname before & after performing the aforementioned process to allow the application in question to be run and the results were identical (saved the result to files & diff'd... I'm not just guessing here). One Step Forward, Half a Step Back: When the Mac OS X 10.6.5 Server update was released, we upgraded our Open Directory Master to it as the changes included the following managed preferences fixes which I hoped might address this issue: Addresses an issue that could prevent managed preferences from being applied when a user logs in on a workstation that has been idle. Fixes an issue that could prevent administrators from bypassing client management settings on a workstation. This seemed to improve the situation slightly. The application in question now usually launches without error. If, and when it does launch with the "You don't have permission to use the application" error, logging the user out and back in seems to correct it. That said, we've since had to add a couple of applications to the user's ~/Applications/ directory and those are still prevented from launching. The workstations are running Mac OS X 10.6.4, the OD Master (which the workstations are bound to) is running Mac OS 10.6.5 Server (although there are two OD Replicas still running 10.6.4 Server), and we're using Workgroup Manager 10.6.3 (which is included with the Server Admin Tools 10.6.5 upgrade) to add the applications (unsigned, as always). This time, I've caught the following in /var/log/system.log when attempting to launch one of the allowed applications from ~/Applications: Dec 22 17:36:24 hostname parentalcontrolsd[43221]: -[ActivityTracker checkApp:csFlags:] [954:username] -- *** Incoming app appears to be masquerading as white listed app and failed signature validation: /Users/username/Applications/FileMaker Pro 5.5/FileMaker Pro.app/Contents/MacOS/FileMaker Pro. Note: This may be a valid app of a different version than what was whitelisted (on a different volume?) Dec 22 17:36:24 hostname [0x0-0xa42a42].com.filemaker.filemakerpro[43304]: launch of /Users/username/Applications/FileMaker Pro 5.5/FileMaker Pro.app/Contents/MacOS/FileMaker Pro was blocked Dec 22 17:36:24 hostname com.apple.launchd.peruser.1340[6375] ([0x0-0xa42a42].com.filemaker.filemakerpro[43304]): Exited with exit code: 255 Dec 22 17:36:24 hostname parentalcontrolsd[43221]: -[ActivityTracker(Private) _removeAppFromWhiteList:] [1362:username] -- *** Couldn't find local user record Running sudo mcxquery -format xml -user username -group groupname includes the following entry for FileMaker Pro 5.5 (and appears to include a full integration of the user's application whitelist & group's application whitelist): <dict> <key>bundleID</key> <string>com.filemaker.filemakerpro</string> <key>displayName</key> <string>FileMaker Pro</string> </dict> Note the lack of <key>appID</key><data> ... </data> which seems to specify a signed application. While whitelisted directories also appear to be correctly listed in the results, they too do not actually allow the applications to be run either. What is going on here?! Where else should I be looking?

  Read the article

• e2fsck extremely slow, although enough memory exists

  - by kaefert

  I've got this external USB-Disk: kaefert@blechmobil:~$ lsusb -s 2:3 Bus 002 Device 003: ID 0bc2:3320 Seagate RSS LLC As can be seen in this dmesg output, there is some problem that prevents that disk from beeing mounted: kaefert@blechmobil:~$ dmesg ... [ 113.084079] usb 2-1: new high-speed USB device number 3 using ehci_hcd [ 113.217783] usb 2-1: New USB device found, idVendor=0bc2, idProduct=3320 [ 113.217787] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1 [ 113.217790] usb 2-1: Product: Expansion Desk [ 113.217792] usb 2-1: Manufacturer: Seagate [ 113.217794] usb 2-1: SerialNumber: NA4J4N6K [ 113.435404] usbcore: registered new interface driver uas [ 113.455315] Initializing USB Mass Storage driver... [ 113.468051] scsi5 : usb-storage 2-1:1.0 [ 113.468180] usbcore: registered new interface driver usb-storage [ 113.468182] USB Mass Storage support registered. [ 114.473105] scsi 5:0:0:0: Direct-Access Seagate Expansion Desk 070B PQ: 0 ANSI: 6 [ 114.474342] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.475089] sd 5:0:0:0: [sdb] Write Protect is off [ 114.475092] sd 5:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 114.475959] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 114.477093] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.501649] sdb: sdb1 [ 114.502717] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.504354] sd 5:0:0:0: [sdb] Attached SCSI disk [ 116.804408] EXT4-fs (sdb1): ext4_check_descriptors: Checksum for group 3976 failed (47397!=61519) [ 116.804413] EXT4-fs (sdb1): group descriptors corrupted! ... So I went and fired up my favorite partition manager - gparted, and told it to verify and repair the partition sdb1. This made gparted call e2fsck (version 1.42.4 (12-Jun-2012)) e2fsck -f -y -v /dev/sdb1 Although gparted called e2fsck with the "-v" option, sadly it doesn't show me the output of my e2fsck process (bugreport https://bugzilla.gnome.org/show_bug.cgi?id=467925 ) I started this whole thing on Sunday (2012-11-04_2200) evening, so about 48 hours ago, this is what htop says about it now (2012-11-06-1900): PID USER PRI NI VIRT RES SHR S CPU% MEM% TIME+ Command 3704 root 39 19 1560M 1166M 768 R 98.0 19.5 42h56:43 e2fsck -f -y -v /dev/sdb1 Now I found a few posts on the internet that discuss e2fsck running slow, for example: http://gparted-forum.surf4.info/viewtopic.php?id=13613 where they write that its a good idea to see if the disk is just that slow because maybe its damaged, and I think these outputs tell me that this is not the case in my case: kaefert@blechmobil:~$ sudo hdparm -tT /dev/sdb /dev/sdb: Timing cached reads: 3562 MB in 2.00 seconds = 1783.29 MB/sec Timing buffered disk reads: 82 MB in 3.01 seconds = 27.26 MB/sec kaefert@blechmobil:~$ sudo hdparm /dev/sdb /dev/sdb: multcount = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 364801/255/63, sectors = 5860533160, start = 0 However, although I can read quickly from that disk, this disk speed doesn't seem to be used by e2fsck, considering tools like gkrellm or iotop or this: kaefert@blechmobil:~$ iostat -x Linux 3.2.0-2-amd64 (blechmobil) 2012-11-06 _x86_64_ (2 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 14,24 47,81 14,63 0,95 0,00 22,37 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util sda 0,59 8,29 2,42 5,14 43,17 160,17 53,75 0,30 39,80 8,72 54,42 3,95 2,99 sdb 137,54 5,48 9,23 0,20 587,07 22,73 129,35 0,07 7,70 7,51 16,18 2,17 2,04 Now I researched a little bit on how to find out what e2fsck is doing with all that processor time, and I found the tool strace, which gives me this: kaefert@blechmobil:~$ sudo strace -p3704 lseek(4, 41026998272, SEEK_SET) = 41026998272 write(4, "\212\354K[_\361\3nl\212\245\352\255jR\303\354\312Yv\334p\253r\217\265\3567\325\257\3766"..., 4096) = 4096 lseek(4, 48404766720, SEEK_SET) = 48404766720 read(4, "\7t\260\366\346\337\304\210\33\267j\35\377'\31f\372\252\ffU\317.y\211\360\36\240c\30`\34"..., 4096) = 4096 lseek(4, 41027002368, SEEK_SET) = 41027002368 write(4, "\232]7Ws\321\352\t\1@[+5\263\334\276{\343zZx\352\21\316`1\271[\202\350R`"..., 4096) = 4096 lseek(4, 48404770816, SEEK_SET) = 48404770816 read(4, "\17\362r\230\327\25\346//\210H\v\311\3237\323K\304\306\361a\223\311\324\272?\213\tq \370\24"..., 4096) = 4096 lseek(4, 41027006464, SEEK_SET) = 41027006464 write(4, "\367yy>x\216?=\324Z\305\351\376&\25\244\210\271\22\306}\276\237\370(\214\205G\262\360\257#"..., 4096) = 4096 lseek(4, 48404774912, SEEK_SET) = 48404774912 read(4, "\365\25\0\21|T\0\21}3t_\272\373\222k\r\177\303\1\201\261\221$\261B\232\3142\21U\316"..., 4096) = 4096 ^CProcess 3704 detached around 16 of these lines every second, so 4 read and 4 write operations every second, which I don't consider to be a lot.. And finally, my question: Will this process ever finish? If those numbers from fseek (48404774912) represent bytes, that would be something like 45 gigabytes, with this beeing a 3 terrabyte disk, which would give me 134 days to go, if the speed stays constant, and e2fsck scans the disk like this completly and only once. Do you have some advice for me? I have most of the data on that disk elsewhere, but I've put a lot of hours into sorting and merging it to this disk, so I would prefer to getting this disk up and running again, without formatting it anew. I don't think that the hardware is damaged since the disk is only a few months and since I can't see any I/O errors in the dmesg output. UPDATE: I just looked at the strace output again (2012-11-06_2300), now it looks like this: lseek(4, 1419860611072, SEEK_SET) = 1419860611072 read(4, "3#\f\2447\335\0\22A\355\374\276j\204'\207|\217V|\23\245[\7VP\251\242\276\207\317:"..., 4096) = 4096 lseek(4, 43018145792, SEEK_SET) = 43018145792 write(4, "]\206\231\342Y\204-2I\362\242\344\6R\205\361\324\177\265\317C\334V\324\260\334\275t=\10F."..., 4096) = 4096 lseek(4, 1419860615168, SEEK_SET) = 1419860615168 read(4, "\262\305\314Y\367\37x\326\245\226\226\320N\333$s\34\204\311\222\7\315\236\336\300TK\337\264\236\211n"..., 4096) = 4096 lseek(4, 43018149888, SEEK_SET) = 43018149888 write(4, "\271\224m\311\224\25!I\376\16;\377\0\223H\25Yd\201Y\342\r\203\271\24eG<\202{\373V"..., 4096) = 4096 lseek(4, 1419860619264, SEEK_SET) = 1419860619264 read(4, ";d\360\177\n\346\253\210\222|\250\352T\335M\33\260\320\261\7g\222P\344H?t\240\20\2548\310"..., 4096) = 4096 lseek(4, 43018153984, SEEK_SET) = 43018153984 write(4, "\360\252j\317\310\251G\227\335{\214`\341\267\31Y\202\360\v\374\307oq\3063\217Z\223\313\36D\211"..., 4096) = 4096 So the numbers in the lseek lines before the reads, like 1419860619264 are already a lot bigger, standing for 1.29 terabytes if those numbers are bytes, so it doesn't seem to be a linear progress on a big scale, maybe there are only some areas that need work, that have big gaps in between them. UPDATE2: Okey, big disappointment, the numbers are back to very small again (2012-11-07_0720) lseek(4, 52174548992, SEEK_SET) = 52174548992 read(4, "\374\312\22\\\325\215\213\23\0357U\222\246\370v^f(\312|f\212\362\343\375\373\342\4\204mU6"..., 4096) = 4096 lseek(4, 46603526144, SEEK_SET) = 46603526144 write(4, "\370\261\223\227\23?\4\4\217\264\320_Am\246CQ\313^\203U\253\274\204\277\2564n\227\177\267\343"..., 4096) = 4096 so either e2fsck goes over the data multiple times, or it just hops back and forth multiple times. Or my assumption that those numbers are bytes is wrong. UPDATE3: Since it's mentioned here http://forums.fedoraforum.org/showthread.php?t=282125&page=2 that you can testisk while e2fsck is running, i tried that, though not with a lot of success. When asking testdisk to display the data of my partition, this is what I get: TestDisk 6.13, Data Recovery Utility, November 2011 Christophe GRENIER <[email protected]> http://www.cgsecurity.org 1 P Linux 0 4 5 45600 40 8 732566272 Can't open filesystem. Filesystem seems damaged. And this is what strace currently gives me (2012-11-07_1030) lseek(4, 212460343296, SEEK_SET) = 212460343296 read(4, "\315Mb\265v\377Gn \24\f\205EHh\2349~\330\273\203\3375\206\10\r3=W\210\372\352"..., 4096) = 4096 lseek(4, 47347830784, SEEK_SET) = 47347830784 write(4, "]\204\223\300I\357\4\26\33+\243\312G\230\250\371*m2U\t_\215\265J \252\342Pm\360D"..., 4096) = 4096 (times are in CET)

  Read the article

• Alternate way to create a clone of a UNIX System

  - by Spirit

  THE STORY: (If you don't like to read much, down below is the question :) ) Where I work we have two HP RP2470 servers same hardware same number of hard drives same everything :). One of them is a production server and runs HP-UX 11.00. The poor ba***rd hasn't been turned off for years and now I have to make a clone of it on the other server - just in case, for redundancy. The problem is simple (or not simple) as I have to make the the other server exactly the same. However the old version of OS (UX 11.00 is a history now) and the old software running on it, have made my task almost impossible. On the production server there is also a cloning/recover utility Ignite-UX. I tried many times to create a recovery tape with it. Then when I load the tape on the backup server, it succeeds with the loading of the tape (no errors no warnings) but on the next restart it fails to load the OS :S and drops into HP`s ISL prompt. --- THE QUESTION: Is there an alternate way to create a clone of the Unix System? The environment is: 1. 2x HP RP2470 Servers (non-Intel), same hardware, same number od HDDs (two each of them) same everything. 2. OS running: HP-UX 11.00 The production server has to be cloned without downtime - sadly :( as I hope that they will reconsider on this one For example (like on Windows platforms), if you try to copy an entire HDD with Windows inside on another HDD, and then put that HDD on another PC it will still work, as long as the hardware is the same. Can I do something like that with a Unix system? Can I somehow COPY the contents of the entire HDD, put those on another HDD, and then just load the HDD into the other server? (If you haven't read the story the servers are exactly the same) Will it work? Can it be done with ordinary commands like cp or dump or something like that? Does any one have a similar experience? --- UPDATE: 26.01.2012 NOTE: The update is related to "The Story". If you haven't read that part then you can skip this update. This is just a short update on the recover logs from the Ignite Tape.. someone with more exp. might notice something.. ... --- READING CONTENTS OF THE IGNITE TAPE --- --- OUTPUT OMITED --- ... ... x ./configure3, 413696 bytes, 808 tape blocks x ./monitor_bpr, 20480 bytes, 40 tape blocks * Download_mini-system: Complete * Loading_software: Begin * Installing boot area on disk. * Enabling swap areas. * Backing up LVM configuration for "vg00". * Processing the archive source (Recovery Archive). * Wed Jan 25 15:27:32 EST 2012: Starting archive load of the source (Recovery Archive). * Positioning the tape (/dev/rmt/0mn). * Archive extraction from tape is beginning. Please wait. * Wed Jan 25 15:39:52 EST 2012: Completed archive load of the source (Recovery Archive). * Executing user specified script: "/opt/ignite/data/scripts/os_arch_post_l". * Running in recovery mode (os_arch_post_l). * Running the ioinit command ("/sbin/ioinit -c") * Creating device files via the insf command. insf: Installing special files for sdisk instance 0 address 0/0/1/1.15.0 insf: Installing special files for sdisk instance 1 address 0/0/2/0.1.0 insf: Installing special files for sdisk instance 2 address 0/0/2/1.15.0 insf: Installing special files for stape instance 0 address 0/0/1/0.3.0 insf: Installing special files for btlan instance 0 address 0/0/0/0 insf: Installing special files for btlan instance 1 address 0/2/0/0 insf: Installing special files for pseudo driver dlpi insf: Installing special files for pseudo driver kepd insf: Installing special files for pseudo driver framebuf insf: Installing special files for pseudo driver sad * Running "/opt/upgrade/bin/tlinstall -v" and correcting transition link permissions. * Constructing the bootconf file. * Setting primary boot path to "0/0/1/1.15.0". * Executing: "/var/adm/sw/products/PHSS_20146/pfiles/iux_postload". * Executing: "/var/adm/sw/products/PHSS_25982/pfiles/iux_postload". NOTE: tlinstall is searching filesystem - please be patient NOTE: Successfully completed * Loading_software: Complete * Build_Kernel: Begin NOTE: Since the /stand/vmunix kernel is already in place, the kernel will not be re-built. Note that no mod_kernel directives will be processed. * Build_Kernel: Complete * Boot_From_Client_Disk: Begin * Rebooting machine as expected. NOTE: Rebooting system. sync'ing disks (0 buffers to flush): 0 buffers not flushed 0 buffers still dirty Closing open logical volumes... Done Console reset done. Boot device reset done. ********** VIRTUAL FRONT PANEL ********** System Boot detected ***************************************** LEDs: RUN ATTENTION FAULT REMOTE POWER FLASH OFF OFF ON ON LED State: Running non-OS code. (i.e. Boot or Diagnostics) ... ... ... --- SERVER IS PERFORMING POST SEQUENCE HERE --- --- OUTPUT OMITED --- ... ... ... ***************************************** ************ EARLY BOOT VFP ************* End of early boot detected ***************************************** Firmware Version 43.50 Duplex Console IO Dependent Code (IODC) revision 1 ------------------------------------------------------------------------------ (c) Copyright 1995-2002, Hewlett-Packard Company, All rights reserved ------------------------------------------------------------------------------ Processor Speed State CoProcessor State Cache Size Number State Inst Data --------- -------- --------------------- ----------------- ------------ 0 650 MHz Active Functional 750 KB 1.5 MB 1 650 MHz Idle Functional 750 KB 1.5 MB Central Bus Speed (in MHz) : 120 Available Memory : 2097152 KB Good Memory Required : 16140 KB Primary boot path: 0/0/1/1.15 Alternate boot path: 0/0/2/1.15 Console path: 0/0/4/1.643 Keyboard path: 0/0/4/0.0 Processor is starting autoboot process. To discontinue, press any key within 10 seconds. 10 seconds expired. Proceeding... Trying Primary Boot Path ------------------------ Booting... Boot IO Dependent Code (IODC) revision 1 HARD Booted. ISL Revision A.00.38 OCT 26, 1994 ISL booting hpux ISL>

  Read the article

• Why are my USB 2.0 devices crashing Windows XP?

  - by BenAlabaster

  Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic ATX motherboard with no identifying markings other than one stamp that says "Rev.B". CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. On board it has 1 x 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors. It has a DVD+/-RW running as master on IDE1 and a 1.44Mb 3.5" floppy drive connected to the floppy connector. It has an 80Gb Western Digital hard drive running as master on IDE0. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. The hard disk is freshly formatted and built with Windows XP Professional/Service Pack 3 and is up to date with all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 hangs the whole machine as soon as it starts up, requiring a hard boot to recover). It's got a Daytek MV150 15" touch screen hooked up to the on board VGA and COM1 sockets with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem: If I hook any devices to the USB 2.0 sockets, it hangs the whole machine and I have to hard boot it to get it back up. If I have any devices attached to the USB 2.0 sockets when I boot up, it hangs before Windows gets to the login prompt and I have to hard boot it to recover. Workarounds found: I can plug the same devices into the on board USB 1.0 sockets and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions: I've seen suggestions that this could be a power problem - that the PSU just doesn't have the wattage to drive these ports. While I'm doubtful this is the problem [after all the motherboard has the same standard connector regardless of the PSU wattage], I tried disabling all the on board devices that I'm not using - on board LAN, the second COM port, the AGP connector etc. through the BIOS in what I'm sure is a futile attempt to reduce the power consumption... I also modified the ACPI and power management settings. It didn't have any noticeable affect, although it didn't do any harm either. Could the wattage of the PSU really cause this problem? If it can, is there anything I need to be aware of when replacing it or do I just need to make sure it's got a higher wattage than the current one? My interpretation was that the wattage only affected the number of drives you could hook up to the power connectors, is that right? I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself, and Windows says the card is installed and working correctly... right up until I connect a device to it. The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference - does anyone have any experience that would suggest this might work? Other thoughts/questions: Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question: Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine?

  Read the article

• Why are my USB 2.0 devices hanging Windows XP?

  - by BenAlabaster

  Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic ATX motherboard with no identifying markings other than one stamp that says "Rev.B". CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. On board it has 1 x 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors - it has a NEC uPD720102 chipset. It has a DVD+/-RW running as master on IDE1 and a 1.44Mb 3.5" floppy drive connected to the floppy connector. It has an 80Gb Western Digital hard drive running as master on IDE0. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. The hard disk is freshly formatted and built with Windows XP Professional/Service Pack 3 and is up to date with all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 hangs the whole machine as soon as it starts up, requiring a hard boot to recover). It's got a Daytek MV150 15" touch screen hooked up to the on board VGA and COM1 sockets with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem: If I hook any devices to the USB 2.0 sockets, it hangs the whole machine and I have to hard boot it to get it back up. If I have any devices attached to the USB 2.0 sockets when I boot up, it hangs before Windows gets to the login prompt and I have to hard boot it to recover. Workarounds found: I can plug the same devices into the on board USB 1.0 sockets and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions: I've seen suggestions that this could be a power problem - that the PSU just doesn't have the wattage to drive these ports. While I'm doubtful this is the problem [after all the motherboard has the same standard connector regardless of the PSU wattage], I tried disabling all the on board devices that I'm not using - on board LAN, the second COM port, the AGP connector etc. through the BIOS in what I'm sure is a futile attempt to reduce the power consumption... I also modified the ACPI and power management settings. It didn't have any noticeable affect, although it didn't do any harm either. Could the wattage of the PSU really cause this problem? If it can, is there anything I need to be aware of when replacing it or do I just need to make sure it's got a higher wattage than the current one? My interpretation was that the wattage only affected the number of drives you could hook up to the power connectors, is that right? I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself, and Windows says the card is installed and working correctly... right up until I connect a device to it. The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference - does anyone have any experience that would suggest this might work? Other thoughts/questions: Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question: Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine? Edit: Updated the USB 2.0 info with reference to actual card - http://www.xpcgear.com/lpnec4u.html

  Read the article

• Unable to import Maven project into IntelliJ IDEA

  - by del

  I'm having problems importing any Maven projects into IntelliJ IDEA. I create an empty Maven project like this: $ mvn archetype:generate -DgroupId=com.mycompany.app -DartifactId=my-app -DarchetypeArtifactId=maven-archetype-quickstart -DinteractiveMode=false Then I try to open the project in IDEA (File Open Project, then choose the pom.xml). A progress box saying "Reading pom.xml" displays for a few minutes, and then just disappears without opening the project. Looking in the IDEA log, I see some connection timeout exceptions like this: 2012-10-03 11:55:55,483 [ 16981] INFO - ution.rmi.RemoteProcessSupport - Port/ID: 18011/Maven2ServerImpl9407569f 2012-10-03 11:56:58,898 [ 80396] WARN - ution.rmi.RemoteProcessSupport - The cook failed to start due to java.net.ConnectException: Connection timed out 2012-10-03 11:57:55,483 [ 136981] WARN - ution.rmi.RemoteProcessSupport - java.rmi.NotBoundException: _DEAD_HAND_ 2012-10-03 11:57:55,484 [ 136982] WARN - ution.rmi.RemoteProcessSupport - at sun.rmi.registry.RegistryImpl.lookup(RegistryImpl.java:106) 2012-10-03 11:57:55,484 [ 136982] WARN - ution.rmi.RemoteProcessSupport - at com.intellij.execution.rmi.RemoteServer.start(RemoteServer.java:73) 2012-10-03 11:57:55,484 [ 136982] WARN - ution.rmi.RemoteProcessSupport - at org.jetbrains.idea.maven.server.RemoteMavenServer.main(RemoteMavenServer.java:22) 2012-10-03 11:58:01,749 [ 143247] ERROR - com.intellij.ide.IdeEventQueue - Error during dispatching of java.awt.event.MouseEvent[MOUSE_RELEASED,(65,116),absolute(64,140),button=1,modifiers=Button1,clickCount=1] on frame0 java.lang.RuntimeException: Cannot reconnect. at org.jetbrains.idea.maven.server.RemoteObjectWrapper.perform(RemoteObjectWrapper.java:82) at org.jetbrains.idea.maven.server.MavenServerManager.applyProfiles(MavenServerManager.java:311) at org.jetbrains.idea.maven.project.MavenProjectReader.applyProfiles(MavenProjectReader.java:369) at org.jetbrains.idea.maven.project.MavenProjectReader.doReadProjectModel(MavenProjectReader.java:98) at org.jetbrains.idea.maven.project.MavenProjectReader.readProject(MavenProjectReader.java:52) at org.jetbrains.idea.maven.project.MavenProject.read(MavenProject.java:405) at org.jetbrains.idea.maven.project.MavenProjectsTree.doUpdate(MavenProjectsTree.java:534) at org.jetbrains.idea.maven.project.MavenProjectsTree.doAdd(MavenProjectsTree.java:481) at org.jetbrains.idea.maven.project.MavenProjectsTree.update(MavenProjectsTree.java:442) at org.jetbrains.idea.maven.project.MavenProjectsTree.updateAll(MavenProjectsTree.java:413) at org.jetbrains.idea.maven.wizards.MavenProjectBuilder.readMavenProjectTree(MavenProjectBuilder.java:198) at org.jetbrains.idea.maven.wizards.MavenProjectBuilder.access$800(MavenProjectBuilder.java:44) at org.jetbrains.idea.maven.wizards.MavenProjectBuilder$3.run(MavenProjectBuilder.java:179) at org.jetbrains.idea.maven.utils.MavenUtil$8.run(MavenUtil.java:388) at com.intellij.openapi.progress.impl.ProgressManagerImpl$TaskRunnable.run(ProgressManagerImpl.java:469) at com.intellij.openapi.progress.impl.ProgressManagerImpl$6.run(ProgressManagerImpl.java:288) at com.intellij.openapi.progress.impl.ProgressManagerImpl$2.run(ProgressManagerImpl.java:178) at com.intellij.openapi.progress.impl.ProgressManagerImpl.executeProcessUnderProgress(ProgressManagerImpl.java:218) at com.intellij.openapi.progress.impl.ProgressManagerImpl.runProcess(ProgressManagerImpl.java:169) at com.intellij.openapi.application.impl.ApplicationImpl$8$1.run(ApplicationImpl.java:641) at com.intellij.openapi.application.impl.ApplicationImpl$6.run(ApplicationImpl.java:434) at java.util.concurrent.Executors$RunnableAdapter.call(Executors.java:441) at java.util.concurrent.FutureTask$Sync.innerRun(FutureTask.java:303) at java.util.concurrent.FutureTask.run(FutureTask.java:138) at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:886) at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:908) at java.lang.Thread.run(Thread.java:662) at com.intellij.openapi.application.impl.ApplicationImpl$1$1.run(ApplicationImpl.java:145) Caused by: java.rmi.RemoteException: Cannot start maven service; nested exception is: java.rmi.ConnectException: Connection refused to host: localhost; nested exception is: java.net.ConnectException: Connection timed out at org.jetbrains.idea.maven.server.MavenServerManager.create(MavenServerManager.java:120) at org.jetbrains.idea.maven.server.MavenServerManager.create(MavenServerManager.java:71) at org.jetbrains.idea.maven.server.RemoteObjectWrapper.getOrCreateWrappee(RemoteObjectWrapper.java:41) at org.jetbrains.idea.maven.server.MavenServerManager$8.execute(MavenServerManager.java:314) at org.jetbrains.idea.maven.server.MavenServerManager$8.execute(MavenServerManager.java:311) at org.jetbrains.idea.maven.server.RemoteObjectWrapper.perform(RemoteObjectWrapper.java:76) ... 27 more Caused by: java.rmi.ConnectException: Connection refused to host: localhost; nested exception is: java.net.ConnectException: Connection timed out at sun.rmi.transport.tcp.TCPEndpoint.newSocket(TCPEndpoint.java:601) at sun.rmi.transport.tcp.TCPChannel.createConnection(TCPChannel.java:198) at sun.rmi.transport.tcp.TCPChannel.newConnection(TCPChannel.java:184) at sun.rmi.server.UnicastRef.newCall(UnicastRef.java:322) at sun.rmi.registry.RegistryImpl_Stub.lookup(Unknown Source) at com.intellij.execution.rmi.RemoteProcessSupport$2.compute(RemoteProcessSupport.java:215) at com.intellij.execution.rmi.RemoteUtil.executeWithClassLoader(RemoteUtil.java:122) at com.intellij.execution.rmi.RemoteProcessSupport.acquire(RemoteProcessSupport.java:212) at com.intellij.execution.rmi.RemoteProcessSupport.acquire(RemoteProcessSupport.java:133) at org.jetbrains.idea.maven.server.MavenServerManager.create(MavenServerManager.java:117) ... 32 more Caused by: java.net.ConnectException: Connection timed out at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:351) at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:213) at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:200) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366) at java.net.Socket.connect(Socket.java:529) at java.net.Socket.connect(Socket.java:478) at java.net.Socket.(Socket.java:375) at java.net.Socket.(Socket.java:189) at sun.rmi.transport.proxy.RMIDirectSocketFactory.createSocket(RMIDirectSocketFactory.java:22) at sun.rmi.transport.proxy.RMIMasterSocketFactory.createSocket(RMIMasterSocketFactory.java:128) at sun.rmi.transport.tcp.TCPEndpoint.newSocket(TCPEndpoint.java:595) ... 41 more I'm using the latest versions of IDEA (11.1.3) and Maven (3.0.4). Any ideas what I am doing wrong?

  Read the article

• Issues using SoapUI with Eclipse

  - by Epitaph

  I get the following in the Error log when using the latest SoapUI 3.5. plugin in Eclipse Galileo on Ubuntu. Also, this seems to continually freeze Eclipse. I have tried a complete uninstall and restarting Eclipse with -clean argument to no avail. Has anyone encountered the same issue? Is there anything I can do to fix this? Could not acquire children from extension: com.eviware.soapui.eclipse.projectContent for Plugin org.eclipse.ui.navigator java.lang.NullPointerException at org.eclipse.ui.internal.navigator.NavigatorContentService.rememberContribution(NavigatorContentService.java:686) at org.eclipse.ui.internal.navigator.extensions.SafeDelegateTreeContentProvider.getElements(SafeDelegateTreeContentProvider.java:97) at org.eclipse.ui.internal.navigator.NavigatorContentServiceContentProvider.getElements(NavigatorContentServiceContentProvider.java:156) at org.eclipse.jface.viewers.StructuredViewer.getRawChildren(StructuredViewer.java:959) at org.eclipse.jface.viewers.ColumnViewer.getRawChildren(ColumnViewer.java:703) at org.eclipse.jface.viewers.AbstractTreeViewer.getRawChildren(AbstractTreeViewer.java:1330) at org.eclipse.jface.viewers.TreeViewer.getRawChildren(TreeViewer.java:390) at org.eclipse.jface.viewers.AbstractTreeViewer.getFilteredChildren(AbstractTreeViewer.java:636) at org.eclipse.jface.viewers.AbstractTreeViewer.getSortedChildren(AbstractTreeViewer.java:602) at org.eclipse.jface.viewers.AbstractTreeViewer.updateChildren(AbstractTreeViewer.java:2578) at org.eclipse.jface.viewers.AbstractTreeViewer.internalRefreshStruct(AbstractTreeViewer.java:1863) at org.eclipse.jface.viewers.TreeViewer.internalRefreshStruct(TreeViewer.java:716) at org.eclipse.jface.viewers.AbstractTreeViewer.internalRefresh(AbstractTreeViewer.java:1838) at org.eclipse.jface.viewers.AbstractTreeViewer.internalRefresh(AbstractTreeViewer.java:1794) at org.eclipse.ui.navigator.CommonViewer.internalRefresh(CommonViewer.java:566) at org.eclipse.jface.viewers.StructuredViewer$8.run(StructuredViewer.java:1484) at org.eclipse.jface.viewers.StructuredViewer.preservingSelection(StructuredViewer.java:1392) at org.eclipse.jface.viewers.TreeViewer.preservingSelection(TreeViewer.java:402) at org.eclipse.jface.viewers.StructuredViewer.preservingSelection(StructuredViewer.java:1353) at org.eclipse.jface.viewers.StructuredViewer.refresh(StructuredViewer.java:1482) at org.eclipse.jface.viewers.ColumnViewer.refresh(ColumnViewer.java:548) at org.eclipse.ui.navigator.CommonViewer.refresh(CommonViewer.java:358) at org.eclipse.ui.navigator.CommonViewer.refresh(CommonViewer.java:515) at org.eclipse.jface.viewers.StructuredViewer.refresh(StructuredViewer.java:1414) at org.eclipse.jface.viewers.StructuredViewer.addFilter(StructuredViewer.java:582) at org.eclipse.ui.internal.navigator.resources.actions.WorkingSetActionProvider.setWorkingSet(WorkingSetActionProvider.java:280) at org.eclipse.ui.internal.navigator.resources.actions.WorkingSetActionProvider$3.propertyChange(WorkingSetActionProvider.java:226) at org.eclipse.ui.internal.navigator.extensions.ExtensionStateModel.firePropertyChangeEvent(ExtensionStateModel.java:135) at org.eclipse.ui.internal.navigator.extensions.ExtensionStateModel.setBooleanProperty(ExtensionStateModel.java:90) at org.eclipse.ui.internal.navigator.resources.actions.WorkingSetActionProvider.restoreState(WorkingSetActionProvider.java:318) at org.eclipse.ui.navigator.NavigatorActionService.initialize(NavigatorActionService.java:372) at org.eclipse.ui.navigator.NavigatorActionService.getActionProviderInstance(NavigatorActionService.java:355) at org.eclipse.ui.navigator.NavigatorActionService.fillActionBars(NavigatorActionService.java:253) at org.eclipse.ui.navigator.CommonNavigatorManager.selectionChanged(CommonNavigatorManager.java:239) at org.eclipse.jface.viewers.Viewer$2.run(Viewer.java:162) at org.eclipse.core.runtime.SafeRunner.run(SafeRunner.java:42) at org.eclipse.core.runtime.Platform.run(Platform.java:888) at org.eclipse.ui.internal.JFaceUtil$1.run(JFaceUtil.java:48) at org.eclipse.jface.util.SafeRunnable.run(SafeRunnable.java:175) at org.eclipse.jface.viewers.Viewer.fireSelectionChanged(Viewer.java:160) at org.eclipse.jface.viewers.StructuredViewer.updateSelection(StructuredViewer.java:2132) at org.eclipse.jface.viewers.StructuredViewer.setSelection(StructuredViewer.java:1669) at org.eclipse.jface.viewers.TreeViewer.setSelection(TreeViewer.java:1124) at org.eclipse.ui.navigator.CommonViewer.setSelection(CommonViewer.java:380) at org.eclipse.ui.navigator.CommonNavigator.selectReveal(CommonNavigator.java:362) at org.eclipse.ui.internal.navigator.actions.LinkEditorAction$3.run(LinkEditorAction.java:101) at org.eclipse.core.runtime.SafeRunner.run(SafeRunner.java:42) at org.eclipse.ui.internal.navigator.actions.LinkEditorAction$2.runInUIThread(LinkEditorAction.java:89) at org.eclipse.ui.progress.UIJob$1.run(UIJob.java:95) at org.eclipse.swt.widgets.RunnableLock.run(RunnableLock.java:35) at org.eclipse.swt.widgets.Synchronizer.runAsyncMessages(Synchronizer.java:134) at org.eclipse.swt.widgets.Display.runAsyncMessages(Display.java:3468) at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3115) at org.eclipse.ui.internal.Workbench.runEventLoop(Workbench.java:2405) at org.eclipse.ui.internal.Workbench.runUI(Workbench.java:2369) at org.eclipse.ui.internal.Workbench.access$4(Workbench.java:2221) at org.eclipse.ui.internal.Workbench$5.run(Workbench.java:500) at org.eclipse.core.databinding.observable.Realm.runWithDefault(Realm.java:332) at org.eclipse.ui.internal.Workbench.createAndRunWorkbench(Workbench.java:493) at org.eclipse.ui.PlatformUI.createAndRunWorkbench(PlatformUI.java:149) at org.eclipse.ui.internal.ide.application.IDEApplication.start(IDEApplication.java:113) at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandle.java:194) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runApplication(EclipseAppLauncher.java:110) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(EclipseAppLauncher.java:79) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:368) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:179) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:559) at org.eclipse.equinox.launcher.Main.basicRun(Main.java:514) at org.eclipse.equinox.launcher.Main.run(Main.java:1311)

  Read the article

• Compiling JS-Test-Driver Plugin and Installing it on Eclipse 3.5.1 Galileo?

  - by leeand00

  I downloaded the source of the js-test-driver from: http://js-test-driver.googlecode.com/svn/tags/1.2 It compiles just fine, but one of the unit tests fails: [junit] Tests run: 1, Failures: 1, Errors: 0, Time elapsed: 0.012 sec [junit] Test com.google.jstestdriver.eclipse.ui.views.FailureOnlyViewerFilterTest FAILED I am using: - ANT 1.7.1 - javac 1.6.0_12 And I'm trying to install the js-test-driver plugin on Eclipse 3.5.1 Galileo Despite the failed test I installed the plugin into my C:\eclipse\dropins\js-test-driver directory by copying (exporting from svn) the compiled feature and plugins directories there, to see if it would yield any hints to what the problem is. When I started eclipse, added the plugin to the panel using Window-Show View-Other... Other-JsTestDriver The plugin for the panel is added, but it displays the following error instead of the plugin in the panel: Could not create the view: Plugin com.google.jstestdriver.eclipse.ui was unable to load class com.google.jstestdriver.eclipse.ui.views.JsTestDriverView. And then bellow that I get the following stack trace after clicking Details: java.lang.ClassNotFoundException: com.google.jstestdriver.eclipse.ui.views.JsTestDriverView at org.eclipse.osgi.internal.loader.BundleLoader.findClassInternal(BundleLoader.java:494) at org.eclipse.osgi.internal.loader.BundleLoader.findClass(BundleLoader.java:410) at org.eclipse.osgi.internal.loader.BundleLoader.findClass(BundleLoader.java:398) at org.eclipse.osgi.internal.baseadaptor.DefaultClassLoader.loadClass(DefaultClassLoader.java:105) at java.lang.ClassLoader.loadClass(Unknown Source) at org.eclipse.osgi.internal.loader.BundleLoader.loadClass(BundleLoader.java:326) at org.eclipse.osgi.framework.internal.core.BundleHost.loadClass(BundleHost.java:231) at org.eclipse.osgi.framework.internal.core.AbstractBundle.loadClass(AbstractBundle.java:1193) at org.eclipse.core.internal.registry.osgi.RegistryStrategyOSGI.createExecutableExtension(RegistryStrategyOSGI.java:160) at org.eclipse.core.internal.registry.ExtensionRegistry.createExecutableExtension(ExtensionRegistry.java:874) at org.eclipse.core.internal.registry.ConfigurationElement.createExecutableExtension(ConfigurationElement.java:243) at org.eclipse.core.internal.registry.ConfigurationElementHandle.createExecutableExtension(ConfigurationElementHandle.java:51) at org.eclipse.ui.internal.WorkbenchPlugin$1.run(WorkbenchPlugin.java:267) at org.eclipse.swt.custom.BusyIndicator.showWhile(BusyIndicator.java:70) at org.eclipse.ui.internal.WorkbenchPlugin.createExtension(WorkbenchPlugin.java:263) at org.eclipse.ui.internal.registry.ViewDescriptor.createView(ViewDescriptor.java:63) at org.eclipse.ui.internal.ViewReference.createPartHelper(ViewReference.java:324) at org.eclipse.ui.internal.ViewReference.createPart(ViewReference.java:226) at org.eclipse.ui.internal.WorkbenchPartReference.getPart(WorkbenchPartReference.java:595) at org.eclipse.ui.internal.Perspective.showView(Perspective.java:2229) at org.eclipse.ui.internal.WorkbenchPage.busyShowView(WorkbenchPage.java:1067) at org.eclipse.ui.internal.WorkbenchPage$20.run(WorkbenchPage.java:3816) at org.eclipse.swt.custom.BusyIndicator.showWhile(BusyIndicator.java:70) at org.eclipse.ui.internal.WorkbenchPage.showView(WorkbenchPage.java:3813) at org.eclipse.ui.internal.WorkbenchPage.showView(WorkbenchPage.java:3789) at org.eclipse.ui.handlers.ShowViewHandler.openView(ShowViewHandler.java:165) at org.eclipse.ui.handlers.ShowViewHandler.openOther(ShowViewHandler.java:109) at org.eclipse.ui.handlers.ShowViewHandler.execute(ShowViewHandler.java:77) at org.eclipse.ui.internal.handlers.HandlerProxy.execute(HandlerProxy.java:294) at org.eclipse.core.commands.Command.executeWithChecks(Command.java:476) at org.eclipse.core.commands.ParameterizedCommand.executeWithChecks(ParameterizedCommand.java:508) at org.eclipse.ui.internal.handlers.HandlerService.executeCommand(HandlerService.java:169) at org.eclipse.ui.internal.handlers.SlaveHandlerService.executeCommand(SlaveHandlerService.java:241) at org.eclipse.ui.internal.ShowViewMenu$3.run(ShowViewMenu.java:141) at org.eclipse.jface.action.Action.runWithEvent(Action.java:498) at org.eclipse.jface.action.ActionContributionItem.handleWidgetSelection(ActionContributionItem.java:584) at org.eclipse.jface.action.ActionContributionItem.access$2(ActionContributionItem.java:501) at org.eclipse.jface.action.ActionContributionItem$5.handleEvent(ActionContributionItem.java:411) at org.eclipse.swt.widgets.EventTable.sendEvent(EventTable.java:84) at org.eclipse.swt.widgets.Widget.sendEvent(Widget.java:1003) at org.eclipse.swt.widgets.Display.runDeferredEvents(Display.java:3880) at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3473) at org.eclipse.ui.internal.Workbench.runEventLoop(Workbench.java:2405) at org.eclipse.ui.internal.Workbench.runUI(Workbench.java:2369) at org.eclipse.ui.internal.Workbench.access$4(Workbench.java:2221) at org.eclipse.ui.internal.Workbench$5.run(Workbench.java:500) at org.eclipse.core.databinding.observable.Realm.runWithDefault(Realm.java:332) at org.eclipse.ui.internal.Workbench.createAndRunWorkbench(Workbench.java:493) at org.eclipse.ui.PlatformUI.createAndRunWorkbench(PlatformUI.java:149) at org.eclipse.ui.internal.ide.application.IDEApplication.start(IDEApplication.java:113) at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandle.java:194) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runApplication(EclipseAppLauncher.java:110) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(EclipseAppLauncher.java:79) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:368) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:179) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source) at java.lang.reflect.Method.invoke(Unknown Source) at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:559) at org.eclipse.equinox.launcher.Main.basicRun(Main.java:514) at org.eclipse.equinox.launcher.Main.run(Main.java:1311) Additionally, if I go to the settings in Window-Preferences and try to view the JS Test Driver Preferences, I get the following dialog: Problem Occurred Unable to create the selected preference page. com.google.jstestdriver.eclipse.ui.WorkbenchPreferencePage Thank you, Andrew J. Leer

  Read the article

• Installshield Development Error durring the Installation process

  - by Alopekos

  Hey guys, I've been stuck by a problem for the past couple days that makes no sense to me. My installer builds fine in the Installshiled IDE but when it is about to finish the installation, int gets two errors then rollbacks: installation failure. Right when the install bar is at about 100%, an error box pops up that states this: "Error 1001.Exception occurred while initializing the installation: System.IO.FileLoadException: Attempt to load an unverifiable executable with fixups (IAT with more than 2 sections or a TLS section.) (Exception from HRESULT: 0x80131019)." The box pops up once, then the installer flashes its status to "rollback" then pops up another error box, then once 'ok'ed it procedes to rollback as usual. I don't understand that error message so i looked in the msi loggings and found this: "InstallShield 13:20:08: Initializing Property Bag... InstallShield 13:20:08: Getting file count from property bag InstallShield 13:20:08: File Count : 7 InstallShield 13:20:08: Sorting Based On Order... InstallShield 13:20:08: This setup is running on a 32-bit Windows...No need to load ISBEW64.exe InstallShield 13:20:08: Registering file C:\Program Files\Cadwell\Easy III\QMWSChartDataServer.dll (32-bit) InstallShield 13:20:09: Registering file C:\Program Files\Cadwell\Easy III\DataDelivery.dll (32-bit) InstallShield 13:20:09: Registering file C:\Program Files\Cadwell\Easy III\QMGlobalData.dll (32-bit) InstallShield 13:20:09: Registering file C:\Program Files\Cadwell\Easy III\QMAdoDB.dll (32-bit) InstallShield 13:20:09: Registering file C:\Program Files\Cadwell\Easy III\QMPatientData.dll (32-bit) InstallShield 13:20:09: Registering file C:\Program Files\Cadwell\Easy III\MedShareGlobalData.dll (32-bit) InstallShield 13:20:09: Registering file C:\Program Files\Cadwell\Easy III\MedDirectory.dll (32-bit) InstallShield 13:20:09: Begin Comitting Property Bag InstallShield 13:20:09: Write KeyList count InstallShield 13:20:09: Finished Comitting Property Bag Action 13:20:09: _EBDE7916DF6AF3B644016C54F66930DC.commit. Action 13:20:09: _EBDE7916DF6AF3B644016C54F66930DC.rollback. Action 13:20:09: _EBDE7916DF6AF3B644016C54F66930DC.install. Error 1001.Exception occurred while initializing the installation: System.IO.FileLoadException: Attempt to load an unverifiable executable with fixups (IAT with more than 2 sections or a TLS section.) (Exception from HRESULT: 0x80131019). MSI (s) (34!84) [13:20:26:455]: Info 2769.Custom Action _EBDE7916DF6AF3B644016C54F66930DC.install did not close 1 MSIHANDLEs. Action ended 13:20:26: InstallFinalize. Return value 3. Action 13:20:26: Rollback. Rolling back action: Rollback: _EBDE7916DF6AF3B644016C54F66930DC.install Rollback: _EBDE7916DF6AF3B644016C54F66930DC.rollback Error 1001.Exception occurred while initializing the installation: System.IO.FileLoadException: Attempt to load an unverifiable executable with fixups (IAT with more than 2 sections or a TLS section.) (Exception from HRESULT: 0x80131019). MSI (s) (34!E8) [13:20:27:036]: Info 2769.Custom Action _EBDE7916DF6AF3B644016C54F66930DC.rollback did not close 1 MSIHANDLEs. Rollback: _EBDE7916DF6AF3B644016C54F66930DC.commit Rollback: ISSelfRegisterFiles Rollback: Registering modules Rollback: Registering type libraries Rollback: Writing system registry values Rollback: Registering program identifiers" All rollbacking commands after this point. For some reason it looks like to me that installshield is trying to launch my program before it finishes the installation, even when I told it to prompt the user to decide to launch. Is this a registering command system that makes it attemp or what? I've been scouring the web all day and I've found some ideas, but I havent seen any solutions as of yet. The installers that I've tried(and failed) have always needed to be Setup.exes, when i try to build a .msi only setup I get this error message. It may help someone who knows more about this system than I do. Your project contains InstallShield prerequisites. A Setup.exe setup launcher is required if you are build a release that includes InstallShield prerequisites. Change your release settings to build Setup.exe, or remove the prerequisites from your project. -7076 There's nothing on the site that has anything from the error code, so I'm at a loss. Thanks for any help possible, I'm an intern and I'm fresh out of ideas... Josh System: XP SP3 Installshield 2010 Pro Install being tested on a VirtualPC

  Read the article

• Git for beginners: The definitive practical guide

  - by Adam Davis

  Ok, after seeing this post by PJ Hyett, I have decided to skip to the end and go with git. So what I need is a beginners practical guide to git. "Beginner" being defined as someone who knows how to handle their compiler, understands to some level what a makefile is, and has touched source control without understanding it very well. "Practical" being defined as this person doesn't want to get into great detail regarding what git is doing in the background, and doesn't even care (or know) that it's distributed. Your answers might hint at the possibilities, but try to aim for the beginner that wants to keep a 'main' repository on a 'server' which is backed up and secure, and treat their local repository as merely a 'client' resource. Procedural note: PLEASE pick one and only one of the below topics and answer it clearly and concisely in any given answer. Don't try to jam a bunch of information into one answer. Don't just link to other resources - cut and paste with attribution if copyright allows, otherwise learn it and explain it in your own words (ie, don't make people leave this page to learn a task). Please comment on, or edit, an already existing answer unless your explanation is very different and you think the community is better served with a different explanation rather than altering the existing explanation. So: Installation/Setup How to install git How do you set up git? Try to cover linux, windows, mac, think 'client/server' mindset. Setup GIT Server with Msysgit on Windows How do you create a new project/repository? How do you configure it to ignore files (.obj, .user, etc) that are not really part of the codebase? Working with the code How do you get the latest code? How do you check out code? How do you commit changes? How do you see what's uncommitted, or the status of your current codebase? How do you destroy unwanted commits? How do you compare two revisions of a file, or your current file and a previous revision? How do you see the history of revisions to a file? How do you handle binary files (visio docs, for instance, or compiler environments)? How do you merge files changed at the "same time"? How do you undo (revert or reset) a commit? Tagging, branching, releases, baselines How do you 'mark' 'tag' or 'release' a particular set of revisions for a particular set of files so you can always pull that one later? How do you pull a particular 'release'? How do you branch? How do you merge branches? How do you resolve conflicts and complete the merge? How do you merge parts of one branch into another branch? What is rebasing? How do I track remote branches? How can I create a branch on a remote repository? Other Describe and link to a good gui, IDE plugin, etc that makes git a non-command line resource, but please list its limitations as well as its good. msysgit - Cross platform, included with git gitk - Cross platform history viewer, included with git gitnub - OS X gitx - OS X history viewer smartgit - Cross platform, commercial, beta tig - console GUI for Linux qgit - GUI for Windows, Linux Any other common tasks a beginner should know? Git Status tells you what you just did, what branch you have, and other useful information How do I work effectively with a subversion repository set as my source control source? Other git beginner's references git guide git book git magic gitcasts github guides git tutorial Progit - book by Scott Chacon Git - SVN Crash Course Delving into git Understanding git conceptually I will go through the entries from time to time and 'tidy' them up so they have a consistent look/feel and it's easy to scan the list - feel free to follow a simple "header - brief explanation - list of instructions - gotchas and extra info" template. I'll also link to the entries from the bullet list above so it's easy to find them later.

  Read the article

• Using MS Standalone profiler in VS2008 Professional

  - by fishdump

  I am trying to profile my .NET dll while running it from VS unit testing tools but I am having problems. I am using the standalone command-line profiler as VS2008 Professional does not come with an inbuilt profiler. I have an open CMD window and have run the following commands (I instrumented it earlier which is why vsinstr gave the warning that it did): C:\...\BusinessRules\obj\Debug>vsperfclrenv /samplegclife /tracegclife /globalsamplegclife /globaltracegclife Enabling VSPerf Sampling Attach Profiling. Allows to 'attaching' to managed applications. Current Profiling Environment variables are: COR_ENABLE_PROFILING=1 COR_PROFILER={0a56a683-003a-41a1-a0ac-0f94c4913c48} COR_LINE_PROFILING=1 COR_GC_PROFILING=2 C:\...\BusinessRules\obj\Debug>vsinstr BusinessRules.dll Microsoft (R) VSInstr Post-Link Instrumentation 9.0.30729 x86 Copyright (C) Microsoft Corp. All rights reserved. Error VSP1018 : VSInstr does not support processing binaries that are already instrumented. C:\...\BusinessRules\obj\Debug>vsperfcmd /start:trace /output:foo.vsp Microsoft (R) VSPerf Command Version 9.0.30729 x86 Copyright (C) Microsoft Corp. All rights reserved. C:\...\BusinessRules\obj\Debug> I then ran the unit tests that exercised the instrumented code. When the unit tests were complete, I did... C:\...\BusinessRules\obj\Debug>vsperfcmd /shutdown Microsoft (R) VSPerf Command Version 9.0.30729 x86 Copyright (C) Microsoft Corp. All rights reserved. Waiting for process 4836 ( C:\Program Files\Microsoft Visual Studio 9.0\Common7\IDE\vstesthost.exe) to shutdown... It was clearly waiting for VS2008 to close so I closed it... Shutting down the Profile Monitor ------------------------------------------------------------ C:\...\BusinessRules\obj\Debug> All looking good, there was a 3.2mb foo.vsp file in the directory. I next did... C:\...\BusinessRules\obj\Debug>vsperfreport foo.vsp /summary:all Microsoft (R) VSPerf Report Generator, Version 9.0.0.0 Copyright (C) Microsoft Corporation. All rights reserved. VSP2340: Environment variables were not properly set during profiling run and managed symbols may not resolve. Please use vsperfclrenv before profiling. File opened Successfully opened the file. A report file, foo_Header.csv, has been generated. A report file, foo_MarksSummary.csv, has been generated. A report file, foo_ProcessSummary.csv, has been generated. A report file, foo_ThreadSummary.csv, has been generated. Analysis completed A report file, foo_FunctionSummary.csv, has been generated. A report file, foo_CallerCalleeSummary.csv, has been generated. A report file, foo_CallTreeSummary.csv, has been generated. A report file, foo_ModuleSummary.csv, has been generated. C:\...\BusinessRules\obj\Debug> Notice the warning about environment variables and using vsperfclrenv? But I had run it! Maybe I used the wrong switches? I don't know. Anyway, loading the csv files into Excel or using the perfconsole tool gives loads of useful info with useless symbol names: *** Loading commands from: C:\temp\PerfConsole\bin\commands\timebytype.dll *** Adding command: timebytype *** Loading commands from: C:\temp\PerfConsole\bin\commands\partition.dll *** Adding command: partition Welcome to PerfConsole 1.0 (for bugs please email: [email protected]), for help type: ?, for a quickstart type: ?? > load foo.vsp *** Couldn't match to either expected sampled or instrumented profile schema, defaulting to sampled *** Couldn't match to either expected sampled or instrumented profile schema, defaulting to sampled *** Profile loaded from 'foo.vsp' into @foo > > functions @foo >>>>> Function Name Exclusive Inclusive Function Name Module Name -------------------- -------------------- -------------- --------------- 900,798,600,000.00 % 900,798,600,000.00 % 0x0600003F 20397910 14,968,500,000.00 % 44,691,540,000.00 % 0x06000040 14736385 8,101,253,000.00 % 14,836,330,000.00 % 0x06000041 5491345 3,216,315,000.00 % 6,876,929,000.00 % 0x06000042 3924533 <snip> 71,449,430.00 % 71,449,430.00 % 0x0A000074 42572 52,914,200.00 % 52,914,200.00 % 0x0A000073 0 14,791.00 % 13,006,010.00 % 0x0A00007B 0 199,177.00 % 6,082,932.00 % 0x2B000001 5350072 2,420,116.00 % 2,420,116.00 % 0x0A00008A 0 836.00 % 451,888.00 % 0x0A000045 0 9,616.00 % 399,436.00 % 0x0A000039 0 18,202.00 % 298,223.00 % 0x06000046 1479900 I am so close to being able to find the bottlenecks, if only it will give me the function and module names instead of hex numbers! What am I doing wrong? --- Alistair.

  Read the article

< Previous Page | 171 172 173 174 175 176 177 178 179 180 181 182  | Next Page >