Search Results

Search found 7776 results on 312 pages for 'configure'.

Page 176/312 | < Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >

• Can two Linux installations share the same /home partition?

  - by huahsin68

  I am currently using OpenSuse 11.4 and Windows XP in laptop. I was planning to remove the Windows and switch to install Kubuntu. My current situation is that I have my root (/) and /home partition separated in OpenSuse. Can I share the /home partition between OpenSuse and Kubuntu? How do I configure Kubuntu to use the existing /home partition during the installation? BTW, the most recent Kubuntu is using ext3 file system whereas my OpenSuse is using ext3. Will this a matter for me to install Kubuntu? Any other issue I need to take care of?

  Read the article

• Is there anyway I can secure my connection when I try to log in to my router remotely?

  - by HardwareMuch

  I'm trying to configure my desktop to be accessed remotely. Here's what I've done so far: enabled wake on lan / remote wake up on all interfaces. I'm using logmein as my remote desktop application. setup DDNS so that I can log in to my router. When I try to remotely log in to my router it says that it is not encrypted there anyone can see my log in information. What can I do to make this a more secure setup? Any other suggestions or different methods will be greatly appreciated.

  Read the article

• configuring cgi-bin using .htaccess

  - by Alexandru

  I'm trying to configure a directory as cgi-bin using .htaccess, but when I try to access the executables, the files are downloaded. I'm using apache2.2. What is the problem? My .htaccess looks like: # cat www/cgi-bin/.htaccess Options +ExecCGI AddHandler cgi-script cgi pl File permissions are # ls -1la www/cgi-bin/ total 60 drwxr-xr-x 2 root root 4096 iun 10 19:22 . drwxr-xr-x 5 root root 4096 iun 10 19:18 .. -rw-r--r-- 1 root root 46 iun 10 19:23 .htaccess -rwxr-xr-x 1 root root 15358 iun 10 19:23 paperload.cgi -rwxr-xr-x 1 root root 12728 iun 10 19:23 papers.cgi -rwxr-xr-x 1 root root 12593 iun 10 19:23 paperview.cgi

  Read the article

• How to setup dhcp3-server to advertise the DNS server the server itself has got from DHCP?

  - by Ivan

  The Ubuntu 10.04 server has eth0 Internet interface configured by means of an ISP's DHCP. At the same time the server has static eth0 LAN interface to which it provides masquerading (NAT) and LAN-internal DHCP service (dhcp3-server). As far as I've understood the manual, I had to hardcode DNS servers to advertise through LAN DHCP with option domain-name-servers in dhcpd.conf. But what if the ISP changes his DNS server IP silently (we use a SOHO-class ISP, so this won't surprise me much)? Can I configure dhcpd to advertise the DNS server the server uses itself, the one gotten by its DHCP client mechanism?

  Read the article

• Help on using mod_rewrite to serve I18N static site

  - by Guandalino

  My static site www.example.com is translated in different languages and files are organized in this hierarchy: / /de index.html seite-1.html /en index.html page-1.html /it index.html pagina-1.html The root contains no files, just one subdirectory for each language the site is translated in, while subdirectories contain pages translated (both content and file name are) in the language corresponding to subdirectory name, de, en, it, etc. The question is: how to configure mod_rewrite so that when a client visits www.example.com it is taken to the correct version of the site, falling back to english version if the required locale is not supported (i.e. Accept-Language header doesn't exist or specifies a language for which the site is not available, e.g. fr)? Thanks for any pointer, I'm here to provide further details or feedback! Best regards

  Read the article

• Reserve one http slot for /server-status?

  - by Stefan Lasiewski

  I have an Apache server which is hanging for some reason. When I normally want to check on the load of an Apache server, I tend to use mod_status via the URL at http://webserver1.example.org/server-status or from the commandline like service httpd fullstatus. However today, the Server is refusing all new connections. Some mysterious problem is causing connections to stall, which means that number of connections fills up all available connections (e.g. The number of connects exceeds the MaxClients setting), and therefore neither http://webserver1.example.org/server-status nor service httpd fullstatus can return anything. Is it possible to configure Apache to reserve one or two slots for the mod_status pages?

  Read the article

• Authentication issues setting up iRedMail on Debian

  - by Sergio Rinaudo

  I'm setting up an exchange server using iRedMail. Following the official iRedMail installation guide (http://www.iredmail.org/install_iredmail_on_debian.html) and the Digital Ocean guide (https://www.digitalocean.com/community/articles/how-to-install-iredmail-on-ubuntu-12-04-x64) I was able to install iRedMail without any problems, so I have all the services up and running. I can configure domains and emails using iRedAdmin BUT I have problem both sending and receiving email, what I get from Roundcube is 'Authentication error' when trying to send an email. Also I can't receive anything. I also tried to connect to the mx server using telnet, it connects, but after the STARTTLS command, when I start to write "MAIL FROM:" the connection is lost. Something in the configuration is not working (at the moment I have the configuration written by the iRedMail installation) but I do not know where, I hope someone can enlight me! Thank you

  Read the article

• Ubuntu based VPN server behind NAT router?

  - by maartenn88

  I have a small intranet- and file-server inside our company, which can only be reached from inside our own network. I'd like to be able to reach the intranet and files on the server from outside the network, however I don't really like the idea of completely opening security by forwarding the ports on our NAT-router, so I'd prefer to enable a VPN possibility for this. So I have a router, which is the DHCP server and has NAT function, and I have an Ubuntu Server with the files and intranet on it. How do I configure these two so that I can make a VPN connection with my network in order to reach the server? thanks in advance for any answer!

  Read the article

• Can't ping IPs for devices not part of Windows Domain

  - by GiddyUpHorsey

  I have a home network with a Trendnet wireless router and a Windows Domain. The DNS server is on a Windows 2000 Server and is configured to forward queries to DNS servers provided by the ISP. The router provides DHCP and is configured with the Windows 2000 Server as the DNS server. When I connect iPhones to the network over WiFi, the router can ping the iPhones through its browser based admin interface, but Windows machines that are part of the Windows Domain cannot. A laptop was connected to the network over WiFi that wasn't joined to the domain and it could see the iPhones. All machines either have a fixed or DHCP allocated IP on the 192.168.0.* subnet. How do I configure the DNS server or the Windows Domain so that Windows machines can see the iPhones?

  Read the article

• Windows 7 Home Premium - Unable to View Chinese Characters Properly

  - by David

  Is there a proper and permanent fix that will restore the display of Chinese Characters on a Windows 7 Home Premium Laptop computer? This problem has been occurring frequently now and a simple reboot no longer does the trick. The square boxes viewed on many applications and websites has been constantly bothering me and I wish to fix it asap. I have done a lot of research on it but have not been successful. Many responses were to install the language packs for Windows 7 Ultimate Users which apparently is not my case or to configure the "Region and Language" settings of the Control Panel, changing the system locale. Does anyone have any suggestions? All would be appreciated!

  Read the article

• Dell PowerEdge 6850 Degraded HDD

  - by Matt

  Good Morning, We have a dell power edge 6850 with a degraded drive in the RAID array. I have never had to recover such an issue, so any help or advice would be welcome. Basically it hasn't affected the server at an operating system level, but has slowed down performance, I have a replacement drive in hand but as this is our main database server I want to proceed with extreme caution. My options as I see them are - Can I just hot swap the degraded drive with the new one and the data will automatically re-sync and we are all back to normal presumably this is dependant on the current raid configuration? reading various comments on-line I may need to re-configure the RAID array and re-build the broken drive? This screams disaster to me with the main worry being that I wipe any other data. Option 1 would of course make my day. Thanks in advance

  Read the article

• iPhone VPN to iTunes Home Sharing

  - by Philip Crumpton

  my goal is to set up a VPN on a Windows machine that contains my iTunes library then connect to that VPN with my iPhone and be able to utilize Home Sharing remotely. I have read that this can easily be set up if the iTunes library is on a Mac (Network Beacon and YazSoft ShareTool are two products I quickly found). I can't find anyone who has had success on a Windows machine, though. In my thinking, there are two options (aside from buying a Mac): 1.) Existing utility that takes care of this for me (like the Mac-only options listed above) and is compatible with iPhone (Hamachi is NOT compatible with iPhone VPN) 2.) Manually configure a VPN to allow Bonjour multicast (can't find any information on this) FYI my router is a Linksys WRT54GL running Tomato 1.28

  Read the article

• Exim: Change sender address when sending mails out of local network

  - by Esa Varemo

  We have a working exim setup at a site, where users can send and receive mails. We are trying to setup a server to send some warnings and errors using email to an address that is outside the local network. The problem is: The program that sends the mails sends them using the username it runs under and the local hostname of the server. This cause the mails to have a sender of format: [email protected]. Exim sends these mails to the ISP's SMTP server, which rejects the mails as they have an illegal or unverifiable sender (the internal address). I'm thinking I should configure exim to rewrite the sender when: - sender's domain is on the local network - receiver's domain is outside the local network I tried setting some kind of rewriting in the exim config, but did not manage to get it to work. I'd show what I have tried, but I ran out of time on the last visit to the site, and had to revert to the original version losing all the changes I tried.

  Read the article

• Cisco Aironet 1200 Series AP Configuration

  - by nonterrorist

  I am attempting to configure a new CISCO Aironet 1200 Series Access Point to have a fixed IP. I have been searching online and I have come to the conclusion that the default IP address of this device is 10.0.0.1. These are the steps I have taken: My machine is plugged directly into the Ethernet port (not the Console port) of the AP. My Ethernet adapter is set to 10.0.0.2. I have reset the AP by holding the Mode button while powering up the device. The issue remains that I can not access 10.0.0.1 through the web, nor can I ping that address.

  Read the article

• One vs. many domain user accounts in a server farm

  - by mjustin

  We are in a migration process of a group of related computers (Intranet servers, SQL, application servers of one application) to a new domain. In the past we used one domain user account for every computer (web1, web2, appserver1, appserver2, sql1, sqlbackup ...) to access central Windows resources like network shares. Every computer also has a local user account with the same name. I am not sure if this is necessary, or if it would be easier to configure and maintain to use one domain user account. Are there key advantages / disadvantages of having one single user account vs. dedicated accounts per computer for this group of background servers? If I am not wrong, one advantage besides easier administration of the user account could be that moving installed applications and services around between the computers does not require a check of the access rights anymore. (Except where IP addresses or ports are used)

  Read the article

• using munin-plugins-rails to monitor rails app perfromance

  - by user2099762

  I have been trying to configure munin-plugins-rails to monitor the performance of our rails apps from Munin. The graphs appear, but no data is shown in the graphs. The log files show Error output from : 2013/06/27-15:39:06 [5540] Request-log-analyzer, by Willem van Bergen and $ 2013/06/27-15:39:06 [5540] Website: http://railsdoctors.com I have tried running Request-log-analyzer manually and pointing it at the production log file, and this reports as % for every item. There is data in the log file. I have tried changing the version of the gems installed, and also the type of the log file, but no luck. Any ideas anyone? Thanks

  Read the article

• linux xorg dual different monitors mouse border

  - by Metiu

  If I hook an external monitor to my Linux laptop and configure it for dual head with the Gnome system tools, I do get them configured with the proper resolution and position (one to the left of the other) The mouse pointer, however, will apparently use the greatest of the two vertical resolutions. This way, when I move up to the top border, the mouse exits the visible screen, traveling in empty space, and this is quite annoying, because you can't go to the upper panel just by going up very fast. Is there a way of enforcing the right resolutions for the mouse, too? Thank you

  Read the article

• Setting up an SVN repository on a windows server to work with XCode.

  - by Tejaswi Yerukalapudi

  Hi, I need to setup an SVN repository for an iPhone / iPad app that I'm working on. It needs to be setup on a Windows server 2003 instance. We run VSS on it, but it doesn't really work all that well with XCode, so I'd like to migrate ASAP. The problem is, I'm a new graduate and this is the first time I'll be using a souce control software, so any tutorials on how to set one up, configure it to work correctly with Macs using XCode are greatly appreciated! Though it's not a priority, I'd also like to try to get my company to ditch VSS for SVN (Been reading this article yesterday - http://www.codinghorror.com/blog/2006/08/source-control-anything-but-sourcesafe.html). How hard is it to migrate existing builds in VSS into something like SVN? Thanks, Teja

  Read the article

• Apache - access two or more virtual hosts from outside

  - by André Alçada Padez

  I have an apache2 server running on my ubuntu system. I have two sites enabled: default (ServerName localhost) site2 (ServerName jslib) I run a windows Virtual Box Machine, to be able to test my stuff in IE. If i type the ubuntu's IP in the addressbar i get the localhost. I was wondering how can i access both (or more as i need it) from other machines. Thanks update I have configured the windows' hosts file like so: 10.0.2.2 localhost 10.0.2.2 jslib It works, but i am really looking for something that i can configure on the server side, and then just change the value of the URL, am i crazy?

  Read the article

• Invoke host's workspace switcher from inside VM

  - by Paul

  When I start a virtual machine (like VMware or VirtualBox) and set it full screen then, from the host OS (in this case Ubuntu), I can beautifully switch to it with the Workspace Switcher. So I switch to the VM like I switch to a virtual screen. But switching back -- from the VM to the host's virtual screens -- seems to be impossible because by entering the VM I loose the host's workspace switcher. Is there a nifty workspace switcher program that runs inside the VM and is able to switch workspaces of the host machine? Edit in light of Frank Thomas' answer, can we configure VirtualBox (or VMware) to not send certain key combinations to the VM, but keep them to the host? Like Super+S. In that approach I would sadly have to miss the nice workspace switcher icon in the guest OS, but that's OK if at least the keyboard trick would work.

  Read the article

• Add "secure" in cookie by httpd server

  - by Abhishek

  How do I have to configure my httpd server to add "Secure" in the cookies? I tried the one in the below link, http://blog.modsecurity.org/2008/12/fixing-both-missing-httponly-and-secure-cookie-flags.html but this did not seem to be working. I inspected the cookie via firebug and found that the cookies have "HttpOnly" but not "Secure". I double checked the configurations and they the same as mentioned in the link. I also noticed that the server response time goes bit high when doing it by mod_security. Is there a better way to do it? Any ideas or pointers to configurations would be helpful

  Read the article

• How to invoke a command using specific proxy server?

  - by Xiè Jìléi

  Some applications support proxy (http proxy or socks proxy), and some are not. For browsers, I can specify proxy server in the preferences/options dialog, and other applications may be able to configure proxy servers in config files. For general purpose, can I invoke a command using a specific proxy? Like following: $ proxy-exec --type sock5 --server 1.2.3.4:8000 -- wget/ftp ... I'm using Ubuntu Maverick. P.S. In win32, it can be implemented by hijacking the socket dlls, maybe, I'm not familiar with Linux programming, but I guess it's possible in Linux. though.

  Read the article

• VNC unattended Server (No user Interaction)

  - by Louis van Tonder

  I worked on a proof on concept a while ago.... whereby I managed to get VNC going in full "unattended" mode... I.e. The VNC Server dials into the viewer... which is running in Listening mode. The same concept of how single click works, but without the user interaction. I cant seem to locate my source files for this concept I worked on... although I have found my shortcut that worked on the Viewer side to listen. "C:\Program Files\UltraVNC\vncviewer.exe" -listen 5007 /noauto /256colors I can not however remember/locate my demo of what the server is doing.... how to configure it. If I remember correctly, the server was also started with command line params that "dialed" into a remote IP/port, that the viewer is listening on. Any ideas? Thanks

  Read the article

• How to remove a package I compiled and installed manually?

  - by macek

  I recently compiled and installed Git on a new install of Mac OS 10.6 but it didn't install the documentation. I now realize I should've used the precompiled package offered here: http://code.google.com/p/git-osx-installer/downloads/list How do I remove all the files that I added to my system using make install with the Git source code? Edit: I've had similar problems in the past with other packages, too. For example, ./configure with the incorrect --prefix= or something. What's the general practice for removing unix packages?

  Read the article

• Wifilink 5100 AGN mass update

  - by ripwads

  We are using a Meru enterprise wireless network with 180 APs. Recently, many users connections are dropping frequently. After much troubleshooting, we have determined much of the trouble is due to some settings in the advanced properties of the wireless nic on our notebooks. Now we want to send out the changes in a Zenworks bundle, but I cannot find these settings in the registry or anywhere we might be able to send out as a remote package. Does anyone know where to find these settings for an Intel wifilink 5100 card other that the NIC properties itself? We really do not want to manually configure 600 notebooks.

  Read the article

< Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >