Search Results

Search found 5568 results on 223 pages for 'dependency analysis'.

Page 176/223 | < Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >

• Extend RAID 1 (HP SmartArray P410i) running Linux

  - by Oliver

  I took over a fairly simple server setup with the following RAID 1 config running Ubuntu 11.10 (Kernel 3.0.0-12-server x86_64): => ctrl all show config Smart Array P410i in Slot 0 (Embedded) (sn: removed) array A (SAS, Unused Space: 1335535 MB) logicaldrive 1 (279.4 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 1 TB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 1 TB, OK) Initially there were two 300GB disks that got replaced by 1TB disks and I now have to extend the logical volume to use that extra space. However, when trying to do so I get the following warning: => ctrl slot=0 ld 1 modify size=max Warning: Extension may not be supported on certain operating systems. Performing extension on these operating systems can cause data to become inaccessible. See ACU documentation for details. Continue? (y/n) Is it safe to say yes or am I at risk of corrupting the file system / loosing data? Rearranging and extending the file system afterwards shouldn't be an issue as I can take the server offline and boot from a gparted live disk. Here's the config of the RAID controller in use: => ctrl all show detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: removed RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: Rev C Firmware Version: 5.12 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: False Drive Write Cache: Disabled SATA NCQ Supported: True And the partition table: Number Start End Size Type File system Flags 1 1049kB 274GB 274GB primary ext4 boot 2 274GB 300GB 25.8GB extended 5 274GB 300GB 25.8GB logical linux-swap(v1)

  Read the article

• Azure's Ubuntu 12.0.4 fails to install PHP5

  - by Alex Kennberg

  Similar to this article from Azure themselves: http://www.windowsazure.com/en-us/manage/linux/common-tasks/install-lamp-stack/ I am trying to install PHP5 on Ubuntu 12.0.4 virtual machine. However, it fails installing the ssl-cert. $ sudo apt-get install php5 Reading package lists... Done Building dependency tree Reading state information... Done php5 is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 49 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up ssl-cert (1.0.28) ... Could not create certificate. Openssl output was: Generating a 2048 bit RSA private key ............................+++ ...................................................................................................................+++ writing new private key to '/etc/ssl/private/ssl-cert-snakeoil.key' ----- problems making Certificate Request 140320238503584:error:0D07A097:asn1 encoding routines:ASN1_mbstring_ncopy:string too long:a_mbstr.c:154:maxsize=64 dpkg: error processing ssl-cert (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: ssl-cert E: Sub-process /usr/bin/dpkg returned an error code (1) Any tips appreciated.

  Read the article

• How do I compile DarWINE in PowerPC Mac OS X 10.4.11...?

  - by Craig W. Davis

  So far I've tried using MacPorts which gives me this error: /Error: Cannot install wine for the arch(s) 'powerpc' because Error: its dependency pkgconfig is only installed for the archs 'i386 ppc'. Error: Unable to execute port: architecture mismatch To report a bug, etc... (I'm not allowed to post two links due to being a new poster...)./ I've also tried using the build script I found in the DarWINE 0.9.12 SDK download that I found on the DarWINE SourceForge.net Project Page... I've also tried the build script that I found at http://code.google.com/p/osxwinebuilder/#Building_Wine_via_the_script... None of these attempts to build DarWINE have actually worked. Whenever I build using the DarWINE build script I run it as follows: /1. I decompress the WINE tarball into ~/Downloads/WINE 2. I cd into ~/Downloads/DarWINE. 3. I run ./winemaker ~/Downloads/WINE/wine-1.2.2 or ./winemaker ~/Downloads/WINE/wine-1.2-rc2 (the reason for trying WINE 1.2-rc2 is that some people managed to get it to build on PowerPC Macs running 10.5.8...)./ I made sure to install Xcode Tools 2.5 & all the SDKs too... The net result is either a syntax type error resulting from trying to run the checked out Google Code DarWINE build script or a bunch of make errors when trying to run the official DarWINE build script that I forcefully extracted from the DarWINE 0.9.12 SDK .dmg file by using Pacifist. I trying to build DarWINE on mid-April 2006 1.42 GHz eMac with DL SuperDrive with Bluetooth 2.0+EDR with 2 GBs of RAM running 10.4.11 as I mentioned earlier... (it came with 10.4.4 on the Mac's Restore DVD-ROM that I ordered from 1-800-SOS-APPL & coconutIdentityCard told me it was made on April 12th 2006 & I know that's right because when I reinstalled Mac OS X 10.4.4 it displayed that it was registered/previously owned by a Hawaiian school...): /make[1]: winegcc: Command not found make[1]: * [main.o] Error 127 make: * [dlls/acledit] Error 2./

  Read the article

• Regular Windows 7 BSOD with Shrew VPN client

  - by Junto

  The Shrew VPN client appears to be a good alternative to the Cisco VPN Client on x64 Windows 7. However, since installing it I've seen fairly regular BSODs. Minidump attached: Microsoft (R) Windows Debugger Version 6.11.0001.404 AMD64 Copyright (c) Microsoft Corporation. All rights reserved. Loading Dump File [D:\Temp\020810-23431-01.dmp] Mini Kernel Dump File: Only registers and stack trace are available Symbol search path is: SRV*d:\symbols*http://msdl.microsoft.com/download/symbols Executable search path is: Windows 7 Kernel Version 7600 MP (8 procs) Free x64 Product: WinNt, suite: TerminalServer SingleUserTS Built by: 7600.16385.amd64fre.win7_rtm.090713-1255 Machine Name: Kernel base = 0xfffff800`0285f000 PsLoadedModuleList = 0xfffff800`02a9ce50 Debug session time: Mon Feb 8 18:08:12.887 2010 (GMT+1) System Uptime: 0 days 7:52:06.120 Loading Kernel Symbols ............................................................... ................................................................ .............. Loading User Symbols Loading unloaded module list .... ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* Use !analyze -v to get detailed debugging information. BugCheck A, {0, 2, 0, fffff800028d50b6} Unable to load image \SystemRoot\system32\DRIVERS\vfilter.sys, Win32 error 0n2 *** WARNING: Unable to verify timestamp for vfilter.sys *** ERROR: Module load completed but symbols could not be loaded for vfilter.sys Probably caused by : vfilter.sys ( vfilter+29a6 ) Followup: MachineOwner Machine is a brand spanking new Dell Precision T5500. Superuser appears to have several recommendations for the Shrew VPN Client as an alternative to the Cisco VPN client on 64 bit machines, so I wondered if anyone here has seen this problem and possibly found a solution to the problem? I've decided to run the VPN client under Windows 7 compatibility mode for the moment (Vista SP2) with administrator privileges to see if it makes a difference. Oddly, the VPN doesn't necessarily need to be connected. I've noticed it when browsing using Google Chrome and Internet Explorer, usually when I open up a new tab. If it carries on I think I'll be forced to shell out the 120 EUR for the NCP Client instead.

  Read the article

• Why do clients on Branch Sites insist on accessing SYSVOL on the HQ DC instead of the branches' RODC?

  - by pepoluan

  I'm still scratching my head over this situation... You see, we have 3 RW DCs in the HQ, and 1 RODC on every branch sites (50+ locations). During startup, a script will pull in some files from \\example.com\SYSVOL\example.com\Common\Data But we have been experiencing bandwidth overload. A traffic analysis indicated that lots of clients in the Branch Sites were trying to access the SYSVOL located in the RW DCs. E.g.: If the RW DCs are 10.1.0.15, 10.2.0.15, and 10.3.0.15, and site 'X' has a subnet of 10.27.0.0/16 (with its RODC at 10.27.0.15), clients at site 'X' seem to insist on accessing \\10.1.0.15\SYSVOL or \\10.2.0.15\SYSVOL or \\10.3.0.15\SYSVOL; they seem to be ignoring the RODC completely. What is going on here? Where should I start investigating what went wrong? BTW, I'm already using DFS-R, and replication have been going on successfully; I can put a small 'canary' file on one of the RW DCs, and within minutes all the RODCs will have successfully replicated the 'canary' file.

  Read the article

• Install PHP mcrypt on Red Hat 4

  - by Chris

  I'm having a very hard time getting mcrypt for PHP installed on a Red Hat 4 server. I've downloaded the rpm but it tells me: error: Failed dependencies: php-common(x86-32) = 5.4.7-2.fc18 is needed by php-mcrypt-5.4.7-2.fc18.i686 rpmlib(FileDigests) <= 4.6.0-1 is needed by php-mcrypt-5.4.7-2.fc18.i686 libc.so.6(GLIBC_2.4) is needed by php-mcrypt-5.4.7-2.fc18.i686 libltdl.so.7 is needed by php-mcrypt-5.4.7-2.fc18.i686 rtld(GNU_HASH) is needed by php-mcrypt-5.4.7-2.fc18.i686 rpmlib(PayloadIsXz) <= 5.2-1 is needed by php-mcrypt-5.4.7-2.fc18.i686 So when I try to install one of those packages, they also require another 8 packages. So I'm diving into dependency hell here. Now if I try to compile mcrypt from source, this is what I get: checking for libmcrypt - version >= 2.5.0... no *** Could not run libmcrypt test program, checking why... *** The test program failed to compile or link. See the file config.log for the *** exact error that occured. This usually means LIBMCRYPT was incorrectly installed *** or that you have moved LIBMCRYPT since it was installed. In the latter case, you *** may want to edit the libmcrypt-config script: no configure: error: *** libmcrypt was not found But I was able to install libmcrypt from an rpm packages successfully. Any suggestions? Also, I cannot use up2date as it requires an active paid account from Red Hat and since the staff has changed rather rapidly in the last year where I work, no one knows if there even was any support accounts.

  Read the article

• Red Hat server minimal install

  - by chmeee

  In a farm of virtualized Red Hat servers, there's the need to install a minimal system for security reasons. Minimal installs have serveral advantages (even no security related): Lees exposure to vulnerabilities (if you don't need it, don't install it) Better update process (less packages to update, less probability of breaking the system) Better performance (no unneeded daemons or processes) The less software you have the easier it is to harden the system Unfortunately, this is not easy because the "Minimal Installation" on Red Hat contains lots of unnecessary packages. There is an added challenge as the farm is running Oracle iAS. I've been told that iAS has dependencies with local graphical envieronment. So finally every server in the farm has gnome, X, etc. I've been searching the web and one solution seems to be making a kickstart script that will intall only the necessary packages. But I find this difficult and have several doubts about how to maintain the system dependencies afterwards. How do you install minimal Red Hat servers? Is it Ok to use kickstart or will I have dependency problems in the installation or in updates? Is there any way to avoid installing the graphical environment for iAS?

  Read the article

• apt-get : Size mismatch

  - by Cédric Girard

  I created a private deb repository to spread a software and it's updates to 600 Ubuntu netbooks. Each time the network is connected, my script try to do a apt-get update. But sometimes (quite often in fact), I have this : Failed to fetch https://myserver/ubuntu/dists/maverick/main/binary-i386/voosicomat.deb Size mismatch The server is an 2.2 Apache, HTTPS only. There is no error on it's logs. Here is the script : apt-get update apt-get dist-upgrade --force-yes --yes Here is the complete output of apt-get Ign https://myserver maverick Release.gpg Ign https://myserver/ubuntu/ maverick/main Translation-en Ign https://myserver maverick Release Ign https://myserver maverick/main i386 Packages/DiffIndex Ign https://myserver maverick/main i386 Packages Ign https://myserver maverick/main i386 Packages Hit https://myserver maverick/main i386 Packages Reading package lists... Reading package lists... Building dependency tree... Reading state information... The following packages will be upgraded: majdb utilitaires voosicomat 3 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 6207kB/6273kB of archives. After this operation, 0B of additional disk space will be used. WARNING: The following packages cannot be authenticated! utilitaires voosicomat majdb Get:1 https://myserver/ubuntu/ maverick/main voosicomat all 2.0.1 [4755kB] Get:2 https://myserver/ubuntu/ maverick/main majdb all 1.0.17 [1452kB] Failed to fetch https://myserver/ubuntu/dists/maverick/main/binary-i386/voosicomat.deb Size mismatch Fetched 7091kB in 21s (324kB/s) E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? Regards Cédric

  Read the article

• Free/opensource application for charting stock prices?

  - by Homunculus Reticulli

  I am looking for a free or FOSS software application for SIMPLY charting stock prices. I am not interested in any of the other nonsense typically bundled with such packages (technical analysis, back testing, tracking etc, etc). All I want to do is the following: Import file from CSV and plot on the chart Ability to scroll the chart left/right (zoom feature would be nice to) Ability to draw straight line (between 2 points) on the plot Ability to plot the graph for different resolutions (for e.g weekly, monthly - or some other custom resolution that I want) print the displayed graph (I can always use screen capture if printing is too much to ask) Thats all I want to do. I am not interested in anything else. I would have thought I could have found something by now. I would have written my own tool (I still will do that at a later stage), but I am a bit short of time at the moment, so I just want something that will do all of the above. Can anyone recommend a package. Last but not the least, I am running on Linux (and would prefer to do so - BUT if I have to, I can run on ahem - you know, Windows)

  Read the article

• Debian - starting UFW (Uncomplicated Firewall) before network interfaces are operational

  - by Tomasz Zielinski

  I want to install UFW on Debian Lenny. Everything looks straightforward except that I don't know where to plug UFW startup script so that it configures iptables before hax0rs can break in. I've reviewed runlevel directories and in /etc/rc0.d, /etc/rc6.d and /etc/rcS.d there are items like these: S35networking -> ../init.d/networking S36ifupdown -> ../init.d/ifupdown Runlevel 0 and 6 are for shutdown and reboot so I guess nothing should be changed there, but runlevel S advertises itself (in README) like something for me: The scripts in this directory whose names begin with an 'S' are executed once when booting the system, even when booting directly into single user mode. The following sequence points are defined at this time: * After the S40 scripts have executed, all local file systems are mounted and networking is available. All device drivers have been initialized. (What bothers me is that both rc0/6.d and rcS.d point to the same networking and ifupdown scripts, but after looking at sources I believe those scripts are smart enough to figure out where to start and where to stop networking.) Now, I think that I should plug my /lib/ufw/ufw-init into /etc/rcS.d, with priority higher that the one of ifupdown and networking, i.e. <= 38 for my /etc/rcS.d. Am I right in this "analysis" ?

  Read the article

• Cannot resolve dependencies when trying to install gnome-libs or xscreensaver on linux

  - by Frank

  I am a linux noob and am trying to install ORacle10g on RHEL5 but am running into difficulties on the requirements stage. The only 2 packages I require is gnome-libs and xscreensaver. I have downloaded both: 'gnome-libs-1.4.1.2.90-44.1.i386.rpm 'xscreensaver-4.18-5.rhel4.11.i386.rpm' But when I try to install them I get dependency errors. I have been trawling sites and forums for 2 days now and am no closer to resolving this and continuing with my Oracle install. To pre-empt possible trouble-shooting questions, here is a list of the dependcies that could not be resolved: For gnome-libs: libdb.so.2(GLIBC_2.0) ORBit libdb.so.2 libllOP.so.0 libORBitCosNaming.so.0 libORBitutil.so.0 libORBit.so.0 libpng.so.2 And it says all the above is needed by package 1:gnome-libs-1.4.1.2.90-44.1.i386(/gnome-libs-1.4.1.2.90-44.1.i386) For xscreensaver: xloadimage is needed by package 1:xscreensaver-4.18-5.rhel4.11.i386(/xscreensaver-4.18-5.rhel4.11.i386) Sorry if I have explained this in a crap way - like I said - linux noob here. Any help with this would be great, its been a long 2 days so far - i need to get this resolved soon. Thanks

  Read the article

• Can MS Services for Unix be deployed and accessed from a shared drive?

  - by Ian C.

  I'm interested in experimenting with replacing our dependency on MKS with MS' Sevices for Unix toolset. I was wondering if anyone has any experience with deploying SFU on a shared drive? We like to, wherever possible, host our dev tools on one central NAS and call to the NAS to access the tools instead of rolling stuff out to each and every desktop. I'm not interested in the NFS support or ActiveState Perl. Really, none of the daemon technology is required here. I'm looking for replacements for the coreutils/binutils stuff you find in Linux (and MKS on Windows): sed, awk, csh, bash, grep, ls, find -- the meat-and-potates command line apps that our build and test scripts are built around. If I limit the install to just the Interix GNU Components (and maybe the Remote Connectivity components) will is run nicely from a shared location? To head off some questions: Yes, I've looked at Cygwin. Unfortunately it's performance in our build and test environment is poor. It runs considerably slower than MKS and it's not a direct drop-in replacement for MKS (thanks to its internal pathing and limitations with commands like 'ps'), so it's a tougher sell. Yes, I'm looking at the MinGW offering in parallel to this.

  Read the article

• Dependencies problems installing openjdk on Ubuntu

  - by Rodnower

  I try to install openjdk-7-jre: sudo apt-get install openjdk-7-jre But I have dependencies problems: Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: openjdk-7-jre : Depends: openjdk-7-jre-headless (= 7u7-2.3.2a-0ubuntu0.12.04.1) but it is not going to be installed Depends: libgif4 (>= 4.1.4) but it is not installable Depends: libatk-wrapper-java-jni (>= 0.30.4-0ubuntu2) but it is not installable Recommends: libgnome2-0 but it is not installable Recommends: libgnomevfs2-0 but it is not going to be installed Recommends: ttf-dejavu-extra but it is not installable E: Unable to correct problems, you have held broken packages. This is version of Ubuntu: Ubuntu 12.04.1 LTS I completely don't know how resolve dependencies... Some one can help me? Thank you for ahead.

  Read the article

• Real benefits of tcp TIME-WAIT and implications in production environment

  - by user64204

  SOME THEORY I've been doing some reading on tcp TIME-WAIT (here and there) and what I read is that it's a value set to 2 x MSL (maximum segment life) which keeps a connection in the "connection table" for a while to guarantee that, "before your allowed to create a connection with the same tuple, all the packets belonging to previous incarnations of that tuple will be dead". Since segments received (apart from SYN under specific circumstances) while a connection is either in TIME-WAIT or no longer existing would be discarded, why not close the connection right away? Q1: Is it because there is less processing involved in dealing with segments from old connections and less processing to create a new connection on the same tuple when in TIME-WAIT (i.e. are there performance benefits)? If the above explanation doesn't stand, the only reason I see the TIME-WAIT being useful would be if a client sends a SYN for a connection before it sends remaining segments for an old connection on the same tuple in which case the receiver would re-open the connection but then get bad segments and and would have to terminate it. Q2: Is this analysis correct? Q3: Are there other benefits to using TIME-WAIT? SOME PRACTICE I've been looking at the munin graphs on a production server that I administrate. Here is one: As you can see there are more connections in TIME-WAIT than ESTABLISHED, around twice as many most of the time, on some occasions four times as many. Q4: Does this have an impact on performance? Q5: If so, is it wise/recommended to reduce the TIME-WAIT value (and what to)? Q6: Is this ratio of TIME-WAIT / ESTABLISHED connections normal? Could this be related to malicious connection attempts?

  Read the article

• SQL Server 2008 Bring Database Online trying to open a file from a drive that doesn't exist

  - by Nai

  This is my error I am facing TITLE: Microsoft.SqlServer.Smo Set offline failed for Database 'Go3D_Retailer ------------------------------ ADDITIONAL INFORMATION: An exception occurred while executing a Transact-SQL statement or batch. (Microsoft.SqlServer.ConnectionInfo) Unable to open the physical file "E:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA\ftrow_Go3D_catalog.ndf". Operating system error 2: "2(failed to retrieve text for this error. Reason: 15105)". Database 'Go3D_Retailer' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. ALTER DATABASE statement failed. (Microsoft SQL Server, Error: 5120) Background to this error I've been trying to move my destination logshipping database to another physical server for analysis purposes. Because I do not have domain keys and active directory set up, I had to hack my process by using the same username/password for both the source and destination servers to get the process to work. Following that, I used this guy's solution to move the destination database to another server. However, this error occurs when I try to bring the database back online. I don't have an E drive on my server and I have no idea why it's trying to open a file from E drive. I have over a 100gb left on my hard disk so it's definitely not a space issue. This sounds like a bug... Any ideas?

  Read the article

• I am looking for a tool to measure or detect "unresponsiveness" of a desktop PC

  - by Tom H

  I have a client that provides some server systems to a hospital, and a support ticket was raised that the desktop application was hanging waiting for the server. We did some extensive testing and its pretty clear that the server is responsive, and the network is fine, and that the problem is on the client end. (no requests are received during the hang etc...) We take a look at the desktop machines and they should be fine, so we raise tickets with the software vendor who says that it must be the hardware, the hardware company says that it is the software, etc etc Anyway, so talking to the nurses, they say that these machines often "hang" for 30 seconds at a time, and sometimes during important moments where they need to get data for a patient who is unwell, such as charts and status. So I want to stick a client on these machines that would be able to detect arbitrary "unresponsiveness" of the keyboard/mouse and log that for analysis later. Obviously I am wary to suggest some application that takes resources and makes the problem even worse, so I would interested to see any tools that would detect these (is it correct to say that the keyboard interrupts are being discarded?) scenarios by looking for the OS discarding the interrupts, or whatever is appropriate here. so go on then serverfault, here is your chance to save a life.... ;-) Edit: I am starting to think that some of the tools associated with real time systems might be appropriate, at least as a diagnostic.

  Read the article

• open_basedir problems with APC and Symfony2

  - by Stephen Orr

  I'm currently setting up a shared staging environment for one of our applications, written in PHP5.3 and using the Symfony2 framework. If I only host a single instance of the application per server, everything works as it should. However, if I then deploy additional instances of the application (which may or may not share the exact same code, dependent on client customisations), I get errors like this: [Tue Nov 06 10:19:23 2012] [error] [client 127.0.0.1] PHP Warning: require(/var/www/vhosts/application1/httpdocs/vendor/doctrine-common/lib/Doctrine/Common/Annotations/AnnotationRegistry.php): failed to open stream: Operation not permitted in /var/www/vhosts/application2/httpdocs/app/bootstrap.php.cache on line 1193 [Tue Nov 06 10:19:23 2012] [error] [client 127.0.0.1] PHP Fatal error: require(): Failed opening required '/var/www/vhosts/application1/httpdocs/app/../vendor/doctrine-common/lib/Doctrine/Common/Annotations/AnnotationRegistry.php' (include_path='.:/usr/share/pear:/usr/share/php') in /var/www/vhosts/application2/httpdocs/app/bootstrap.php.cache on line 1193 Basically, the second site is trying to require the files from the first site, but due to open_basedir restrictions it can't do that. I'm not willing to disable open_basedir as that is only masking the problem instead of solving it, and creates a dependency between applications that should not be present. I initially believed this was related to a Symfony2 error, but I've now tracked it down to an issue with APC; disabling APC also solves the error, but I'm concerned about the performance impact of doing so. Does anyone have any suggestions on what I might be able to do?

  Read the article

• Using %v in Apache LogFormat definition matches ServerName instead of specific vhost requested

  - by Graeme Donaldson

  We have an application which uses a DNS wildcard, i.e. *.app.example.com. We're using Apache 2.2 on Ubuntu Hardy. The relevant parts of the Apache config are as follows. In /etc/apache2/httpd.conf: LogFormat "%v %h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" vlog In /etc/apache2/sites-enabled/app.example.com: ServerName app.example.com ServerAlias *.app.example.com ... CustomLog "|/usr/sbin/vlogger -s access.log /var/log/apache2/vlogger" vlog Clients access this application using their own URL, e.g. company1.app.example.com, company2.app.example.com, etc. Previously, the %v in the LogFormat directive would match the hostname of the client request, and we'd get several subdirectories under /var/log/apache2/vlogger corresponding to the various client URLs in use. Now, %v appears to be matching the ServerName value, so we only get one log under /var/log/apache2/vlogger/app.example.com. This breaks our logfile analysis because the log file has no indication of which client the log relates to. I can fix this easily by changing the LogFormat to this: LogFormat "%{Host}i %h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" vlog This will use the HTTP Host: header to tell vlogger which subdirectory to create the logs in and everything will be fine. The only concern I have is that this has worked in the past and I can't find any indication that this has changed recently. Is anyone else using a similar config, i.e. wildcard + vlogger and using %v? Is it working fine?

  Read the article

• How to get automatic upgrades to work on Ubuntu Server?

  - by J. Pablo Fernández

  I followed the documentation for enabling automatic upgrades in Ubuntu servers, but it's not really updating anything at all. My /etc/apt/apt.conf.d/50unattended-upgrades looks almost like the default. // Automatically upgrade packages from these (origin, archive) pairs Unattended-Upgrade::Allowed-Origins { "Ubuntu karmic-security"; "Ubuntu karmic-updates"; }; // List of packages to not update Unattended-Upgrade::Package-Blacklist { // "vim"; // "libc6"; // "libc6-dev"; // "libc6-i686"; }; // Send email to this address for problems or packages upgrades // If empty or unset then no email is sent, make sure that you // have a working mail setup on your system. The package 'mailx' // must be installed or anything that provides /usr/bin/mail. Unattended-Upgrade::Mail "[email protected]"; // Automatically reboot *WITHOUT CONFIRMATION* if a // the file /var/run/reboot-required is found after the upgrade //Unattended-Upgrade::Automatic-Reboot "false"; The directory /var/log/unattended-upgrades/ is empty. Running /etc/init.d/unattended-upgrades start is not very nice: root@mozart:~# /etc/init.d/unattended-upgrades start Checking for running unattended-upgrades: root@mozart:~# Something seems to be broken, but I'm not sure why. I have pending updates and they are not being applied: root@mozart:~# aptitude safe-upgrade Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done The following packages will be upgraded: linux-libc-dev 1 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 0B/743kB of archives. After unpacking 4096B will be used. Do you want to continue? [Y/n/?] In all the servers I have, unattended upgrades seems to have been disabled: root@mozart:~# apt-config shell UnattendedUpgradeInterval APT::Periodic::Unattended-Upgrade root@mozart:~# Any ideas what am I missing?

  Read the article

• systemd: enabling cherokee service as a `unit file`

  - by Calvin Cheng

  So I am learning how to use systemd to initialize my services automatically on server reboot. So of course, I first make sure I have systemd and some optional systemd related packages installed. pacman -S systemd initscripts-systemd Installation seems to go well and checking, I can see that systemd and its dependency libsystemd are installed. And the optional package initscripts-systemd is also installed:- [root@li280-195 ~]# pacman -Ss systemd extra/libsystemd 44-5 [installed] systemd client libraries extra/systemd 44-5 [installed] system and service manager extra/systemd-sysvcompat 2-2 sysvinit compat symlinks for systemd community/initscripts-systemd 20120412-1 [installed] Arch specific systemd initialization/bootup scripts for systemd community/systemd-arch-units 20120412-2 Arch specific Systemd unit files Next, I ensure that systemd is loaded up when my server reboots, via grub in grub's /boot/grub/menu.lst file like this:- kernel /boot/vmlinuz root=/dev/xvda ro init=/bin/systemd Rebooting my server to check, all loads up well and I can check that systemd is operational via:- systemctl list-unit-files However, I don't see my cherokee initialization script (which is simply created at /etc/rc.d/cherokee when I installed cherokee earlier via pacman -S cherokee) being listed as one of my unit files. So the question is, how do I do that? How do I put my cherokee initialization script under systemd's control?

  Read the article

• installing Conkeror on Ubuntu 12.04

  - by Menelaos Perdikeas

  I am reading the instructions on conkeror site (and elsewhere) on how to install conkeror on Ubuntu (I am using Ubuntu 12_04 LTS) and it seems that the correct sequence is: sudo apt-add-repository ppa:xtaran/conkeror sudo apt-get update sudo apt-get install conkeror conkeror-spawn-process-helper The first step (apt-add-repository) seems to execute without a problem, giving the following output: You are about to add the following PPA to your system: Conkeror Debian packages for Ubuntu releases without xulrunner (i.e. for 11.04 Natty and later) More info: https://launchpad.net/~xtaran/+archive/conkeror Press [ENTER] to continue or ctrl-c to cancel adding it Executing: gpg --ignore-time-conflict --no-options --no-default-keyring --secret- keyring /tmp/tmp.Re7pWaDEQF --trustdb-name /etc/apt/trustdb.gpg --keyring /etc/apt/trusted.gpg --primary-keyring /etc/apt/trusted.gpg --keyserver hkp://keyserver.ubuntu.com:80/ --recv CB29CBE050EB1F371BAB6FE83BE0F86A6D689050 gpg: requesting key 6D689050 from hkp server keyserver.ubuntu.com gpg: key 6D689050: "Launchpad PPA for Axel Beckert" not changed gpg: Total number processed: 1 gpg: unchanged: 1 However, the apt-get update seems unable to fetch packages from the newly added PPA, with its output ending in: Hit http://security.ubuntu.com precise-security/restricted Translation-en Hit http://security.ubuntu.com precise-security/universe Translation-en Err http://ppa.launchpad.net precise/main Sources 404 Not Found Ign http://extras.ubuntu.com precise/main Translation-en_US Err http://ppa.launchpad.net precise/main i386 Packages 404 Not Found Ign http://extras.ubuntu.com precise/main Translation-en Ign http://ppa.launchpad.net precise/main Translation-en_US Ign http://ppa.launchpad.net precise/main Translation-en W: Failed to fetch http://ppa.launchpad.net/xtaran/conkeror/ubuntu/dists/precise /main/source/Sources 404 Not Found W: Failed to fetch http://ppa.launchpad.net/xtaran/conkeror/ubuntu/dists/precise/main/binary-i386/Packages 404 Not Found E: Some index files failed to download. They have been ignored, or old ones used instead. Accordingly, apt-get-install conkeror fails with: mperdikeas@mperdikeas:~$ sudo apt-get install conkeror Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package conkeror Any ideas what might be wrong ?

  Read the article

• Why does this preseed for gitolite fail?

  - by troutwine

  I'm installing gitolite on a Debian Squeeze box with the following preseed: gitolite gitolite/gituser string git gitolite gitolite/adminkey string ssh-rsa AAAAB3ECT gitolite gitolite/gitdir string /var/lib/git On installation: # debconf-set-selections /var/cache/debconf/gitolite.preseed # apt-get install gitolite Reading package lists... Done Building dependency tree Reading state information... Done Suggested packages: git-daemon-run gitweb The following NEW packages will be installed: gitolite 0 upgraded, 1 newly installed, 0 to remove and 26 not upgraded. Need to get 0 B/114 kB of archives. After this operation, 348 kB of additional disk space will be used. Preconfiguring packages ... Selecting previously deselected package gitolite. (Reading database ... 24715 files and directories currently installed.) Unpacking gitolite (from .../gitolite_1.5.4-2+squeeze1_all.deb) ... Setting up gitolite (1.5.4-2+squeeze1) ... adduser: The home dir must be an absolute path. dpkg: error processing gitolite (--configure): subprocess installed post-installation script returned error exit status 1 configured to not write apport reports Errors were encountered while processing: gitolite E: Sub-process /usr/bin/dpkg returned an error code (1) Why? The pre-seed was extracted from a manually configured installation, per here and exists without issue on another machine.

  Read the article

• No Homegroup Computers, Network Troubleshooter Fails

  - by Mokubai

  I have a problem with my Windows 7 Homegroup, between two Windows 7 Home Premium machines. On one machine I get this: The other machine in the Homegroup is perfectly happy and is able to see and browse this faulty machine as if there is nothing wrong. The Network and Sharing Center shows that I am joined to a Homegroup on my "Home" network and nothing is out of the ordinary. I have tried leaving the Homegroup and rejoining/recreating it several times and that does nothing at all. Normal browsing to machine names and looking through folders seems to work, but it's a much more clunky way to get stuff compared to the convenience of the Homegroup facilities. Starting the troubleshooter detects some problems with a "Peer Networking" (PNRpr or something like that) service not starting but fails to fix anything. Sure enough when I go to view the services via Control Panel - Administrative Tools - Services I see that both the "Peer Name Resolution Protocol" and "Peer Networking Grouping" services are stopped. Attempting to start the "Peer Networking Grouping" gives an error that a dependency service will not start, the only service it is dependant on is the "Peer Name Resolution Protocol" so I try to start that and I get an error saying that the "service could not start due to error 0x80630801" This has happened before and I have fixed it then by using System Restore and restoring the machine to a week before when I knew it had all worked. This time though I cannot remember when I last used the Homegroup from this machine and I've installed quite a bit so I don't want to go fumbling through restore points trying to find one that works... Can anyone tell me if there is a way to reset things so that this machine is able to use the Homegroup again?

  Read the article

• Recover data from physically damaged harddrive. What are my options?

  - by Michael Kniskern

  I was trying to replace the power supply in my desktop PC and ended up physically damaging the data connection from the hard drive to the motherboard. The plastic shelf for the copper prongs on the hard drive broke into the cable. Here is a picture of my handy work: I went to Best Buy Geek Squad to discuss my options and they said that they will need to send it to the recover center it could cost anywhere between $250 to $1600 USD to recover the data out the hard drive Is this reasonable for data recovery from a physically damaged hard drive? Are there any other options I can explore? I am going to talk to the data doctors to see what my options are. Update I took the HD to Data Doctors, and they told me that the SATA connection was broken to they would need to replaced the data connector and then copy the data to a brand new hard drive. So, with the initial analysis, cost of replacement parts, and data recovery fee it came out to $865.00 USD. The technician specifically stated if this was an older hard drive that would just need to replace the data connector. But because there is specific information related to the individual hard drive in the flash ROM, they need to transfer the data to a brand new hard drive.

  Read the article

• Control Panel as menu includes a blank item

  - by Matthew Ferreira

  When viewed as a menu attached to the Start Menu in Windows 7 Ultimate x64, the Control Panel contains a blank item. It looks like this: This item cannot be deleted or removed. I also cannot create a shortcut to it. No error message is displayed, instead simply nothing happens. I've tried using Shell Object Editor (using Run as Administrator) to find out if there is an errant entry on the Control Panel, but many entries (almost two dozen) are blank. There are several valid entries as well. I've looked through the registry and through C:\Windows, \system32, and \SysWOW64 but have had no success. I looked at this question, but I am not using Windows XP and thus have no option to use Tweak UI's Rebuild Icons function. Please note that this is no empty entry in the Control Panel when opened normally, only when attached to the Start Menu as a menu. I have compared the list of entries on the attached menu to the normal Control Panel and other than the blank entry, they are exactly the same. Nothing is missing from one or the other. I've also compared the menu and the normal view to reference images and lists of Control Panel items and have found no irregularities. Is anyone familiar with this problem or know of a solution? I've performed virus and malware scans and found nothing. I've used CCleaner with no change. Nothing with Shell Object Editor. Nothing with Registry Editor. Certainly someone here knows how to fix this. My only guess is the many blank entries visible in Shell Object Editor, but I am reluctant to delete that many items without further analysis and guidance. I appreciate your time and consideration.

  Read the article

< Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >