Search Results

Search found 20448 results on 818 pages for 'ip address'.

Page 177/818 | < Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >

• How is it possible that I can do a host lookup but not a curl?

  - by Daniel Quinn

  Has anyone ever seen this before? Note that this happens not only with google.com, but with every domain I try. It's a wireless connection (WEP), but I'm not sure how that would be relevant: $ curl -v google.com # This takes about 60s to return * getaddrinfo(3) failed for google.com:80 * Couldn't resolve host 'google.com' * Closing connection #0 curl: (6) Couldn't resolve host 'google.com' $ host google.com google.com has address 209.85.148.106 google.com has address 209.85.148.147 google.com has address 209.85.148.99 google.com has address 209.85.148.103 google.com has address 209.85.148.104 google.com has address 209.85.148.105 google.com mail is handled by 30 alt2.aspmx.l.google.com. google.com mail is handled by 40 alt3.aspmx.l.google.com. google.com mail is handled by 50 alt4.aspmx.l.google.com. google.com mail is handled by 10 aspmx.l.google.com. google.com mail is handled by 20 alt1.aspmx.l.google.com. $ cat /etc/resolv.conf # Generated by NetworkManager nameserver 192.168.1.201 $ cat /etc/hosts 127.0.0.1 localhost ::1 localhost $ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.1.254 0.0.0.0 UG 0 0 0 wlan0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0

  Read the article

• Why does redis report limit of 1024 files even after update to limits.conf?

  - by esilver

  I see this error at the top of my redis.log file: Current maximum open files is 1024. maxclients has been reduced to 4064 to compensate for low ulimit. I have followed these steps to the letter (and rebooted): Moreover, I see this when I run ulimit: ubuntu@ip-XX-XXX-XXX-XXX:~$ ulimit -n 65535 Is this error specious? If not, what other steps do I need to perform? I am running redis 2.8.13 (tip of the tree) on Ubuntu LTS 14.04.1 (again, tip of the tree). Here is the user info: ubuntu@ip-XX-XXX-XXX-XXX:~$ ps aux | grep redis root 1027 0.0 0.0 66328 2112 ? Ss 20:30 0:00 sudo -u ubuntu /usr/local/bin/redis-server /etc/redis/redis.conf ubuntu 1107 19.2 48.8 7629152 7531552 ? Sl 20:30 2:21 /usr/local/bin/redis-server *:6379 The server is therefore running as ubuntu. Here are my limits.conf file without comments: ubuntu@ip-XX-XXX-XXX-XXX:~$ cat /etc/security/limits.conf | sed '/^#/d;/^$/d' ubuntu soft nofile 65535 ubuntu hard nofile 65535 root soft nofile 65535 root hard nofile 65535 And here is the output of sysctl fs.file-max: ubuntu@ip-XX-XXX-XXX-XXX:~$ sysctl -a| grep fs.file-max sysctl: permission denied on key 'fs.protected_hardlinks' sysctl: permission denied on key 'fs.protected_symlinks' fs.file-max = 1528687 sysctl: permission denied on key 'kernel.cad_pid' sysctl: permission denied on key 'kernel.usermodehelper.bset' sysctl: permission denied on key 'kernel.usermodehelper.inheritable' sysctl: permission denied on key 'net.ipv4.tcp_fastopen_key' as sudo ubuntu@ip-10-102-154-226:~$ sudo sysctl -a| grep fs.file-max fs.file-max = 1528687 Also, I see this error at the top of the redis.log file, not sure if it's related. It makes sense that the ubuntu user isn't allowed to change max open files, but given the high ulimits I have tried to set he shouldn't need to: [1050] 23 Aug 21:00:43.572 # You requested maxclients of 10000 requiring at least 10032 max file descriptors. [1050] 23 Aug 21:00:43.572 # Redis can't set maximum open files to 10032 because of OS error: Operation not permitted.

  Read the article

• Ping and crawling not working, site still resolving

  - by Andrew Alexander

  Ok, so we're trying to figure out why the site of one of our clients isn't being crawled by Google (we've ruled out robots.txt or meta tags) When we go to the site, either IP address or domain name, the site resolves, everything works. However, Google is getting a 302 redirect (which it apparently isn't following for crawling), and when we ping the address, it times out (note, the site is still resolving in the browser throughout all of this). The site is built in ASP.Net (I assume C#) and so my thoughts were that it was an errant redirect rule, or some other sort of server side issue. We also thought that it might be due to incorrect domain pointing (but if we try to ping the IP, it doesn't work, so that sorta rules that out). We're really not sure what is causing all of these errors, or even if they have one single source. Anyone have any ideas what could be going on? Do you need any more information? To boil it down in a TL; dr: * Site resolving in browser, both IP and domain name. No problems here. * Site not being crawled by Google (gets a 302 it doesn't seem to follow) - it is not due to robots.txt or meta tags * Ping is not working for the IP address. This is very odd, because again, the IP address seems to work fine in the browser. * Our thoughts are either redirect rule issue, domain pointing issue, or possibly some errant code - or some combination of the three

  Read the article

• Someone used or hacked my computer to commit a crime? what defense do I have?

  - by srguws

  Hello, I need IMMEDIATE Help on a computer crime that I was arrested for. It may involve my computer, my ip, and my ex-girlfriend being the true criminal. The police do not tell you much they are very vague. I was charged though! So my questions are: -If someone did use my computer at my house and business and post a rude craigslist ad about a friend of my girlfriend at the time from a fake email address, how can I be the ONLY one as a suspect. Also how can I be charged. I noticed the last few days there are many ways to use other peoples computers, connections, etc. Here are a few things I found: You can steal or illegally use an ip addresss or mac address. Dynamic Ip is less secure and more vulnerable than static. People can sidejack and spoof your Mac, Ip, etc. There is another thing called arp spoofing. I am sure this is more things, but how can I prove that this happened to me or didnt happen to me. -The police contacted Craigslist, the victim, aol, and the two isp companies. They say they traced the IP's to my business and my home. My ex was who I lived with and had a business with has access to the computers and the keys to bothe buildings. My brother also lives and works with me. My business has many teenagers who use the computer and wifi. My brother is a college kid and also has friends over the house and they use the computer freely. So how can they say it was me because of an angry ex girlfriend.

  Read the article

• Destination NAT Onto the Same Network from internal clients

  - by mivi

  I have a DSL router which acts as NAT (SNAT & DNAT). I have setup a server on internal network (10.0.0.2 at port 43201). DSL router was configured to "port forward" (or DNAT) all incoming connections to 10.0.0.2:43201. I created a virtual server for port forwarding on DSL router. I also added following iptables rules for port forwarding. iptables -t nat -A PREROUTING -p tcp -i ppp_0_1_32_1 --dport 43201 -j DNAT --to-destination 10.0.0.2:43201 iptables -I FORWARD 1 -p tcp -m state --state NEW,ESTABLISHED,RELATED -d 10.0.0.2 --dport 43201 -j ACCEPT # ppp_0_1_32_1 is routers external interface. # routers internal IP address is 10.0.0.1 and server is setup at 10.0.0.2:43201 Problem is that connections coming from external IP addresses are able to access internal server using External IP address, but internal clients (under NAT) are not able to access server using external IP address. Example: http://<external_address>:43201 is working from external clients But, internal clients are not able to access using http://<external_address>:43201 This seems to be similar to the problem described in http://www.netfilter.org/documentation/HOWTO/NAT-HOWTO-10.html (NAT HOW-TO Destination NAT Onto the Same Network). Firstly, I am not able to understand why is this a problem for internal clients? Secondly, what iptables rule will enable internal clients to access server using external IP address? Please suggest.

  Read the article

• Multiple VLANs in the same subnet

  - by A.J.

  Is it possible to have multiple VLANs in the same subnet, with the same gateway address (TMG)? I want to avoid having many Subnets (and vNIC's in TMG) just to isolate sets of a few hosts. IP: 10.0.0.1 (TMG server) VLAN:1 ~ 3 IP: 10.0.0.11 ~ 20 (Hosts group 1) VLAN:1 IP: 10.0.0.21 ~ 30 (Hosts group 2) VLAN:2 IP: 10.0.0.31 ~ 40 (Hosts group 3) VLAN:3 Note that I don't want them to connect to each other, so ARP/inter-vlan routing (within the subnet) is not required. The gateway is running in a VM within ESXi 5, I can pass the VLans to the VM using VGT or VLan Range, but I don't know how the OS/TMG should handle them.

  Read the article

• Make 2 virtual machines ping in virtual box

  - by darkheir

  I'm trying to make 2 virtual machines communicate in Virtual Box, but whitout any success. Here are the step I have done: I setted both VMs in Internal networking mode (using VBoxManage modifyvm "VM name" --nic<x> intnet) I setted the DHCP server that is built into VirtualBox to manage IP addresses :VBoxManage dhcpserver add --netname intnet --ip 10.13.13.100 --netmask 255.255.255.0 --lowerip 10.13.13.101 --upperip 10.13.13.254 --enable But then both of the VM have the same IP Adresse (10.13.13.101) and even if set the IP manually, the Virtual Machines are not pinging each other.

  Read the article

• How to I alias a hostname?

  - by Jonas Byström

  Is it possible to keep a network alias - without specifying the IP address in the hosts file? For instance, I have abcd.efgh.com but want abcd -> abcd.efgh.com so that ping and ssh work as they normally would. I want it to work with dynamic IP on abcd.efgh.com, that's why I don't want to state the IP address explicitly.

  Read the article

• Selecting Interface for SSH Port Forwarding

  - by Eric Pruitt

  I have a server that we'll call hub-server.tld with three IP addresses 100.200.130.121, 100.200.130.122, and 100.200.130.123. I have three different machines that are behind a firewall, but I want to use SSH to port forward one machine to each IP address. For example: machine-one should listen for SSH on port 22 on 100.200.130.121, while machine-two should do the same on 100.200.130.122, and so on for different services on ports that may be the same across all of the machines. The SSH man page has -R [bind_address:]port:host:hostport listed I have gateway ports enabled, but when using -R with a specific IP address, server still listens on the port across all interfaces: machine-one: # ssh -NR 100.200.130.121:22:localhost:22 [email protected] hub-server.tld (Listens for SSH on port 2222): # netstat -tan | grep LISTEN tcp 0 0 100.200.130.121:2222 0.0.0.0:* LISTEN tcp 0 0 :::22 :::* LISTEN tcp 0 0 :::80 :::* LISTEN Is there a way to make SSH forward only connections on a specific IP address to machine-one so I can listen to port 22 on the other IP addresses at the same time, or will I have to do something with iptables? Here are all the lines in my ssh config that are not comments / defaults: Port 2222 Protocol 2 SyslogFacility AUTHPRIV PasswordAuthentication yes ChallengeResponseAuthentication no GSSAPIAuthentication no GSSAPICleanupCredentials no UsePAM yes AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL AllowTcpForwarding yes GatewayPorts yes X11Forwarding yes ClientAliveInterval 30 ClientAliveCountMax 1000000 UseDNS no Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• Installing SSL certs with nginx on Amazon EC2

  - by Ethan

  I finally got a cert from an authority and am struggling to get things working. I've created the appropriate combined certificate (personal + intermediate + root) and nginx is pointing to it. I got an elastic IP and connected it to my EC2 instance. My DNS records point to that IP. But when I point the browser to the hostname, I get the standard "Connection Untrusted" bit, with ssl_error_bad_cert_domain. Port 443 is open - I can get to the site over https if I ignore the warning. Weird thing is, under technical details, it lists the domain I tried to access as valid! When I try and diagnose with ssl testing sites, they don't even detect a certificate! What am I missing here? domain is yanlj.coinculture.info. Note I've got coinculture.info running on a home server without a dedicated IP and have the same problem, but I'll be moving that to the same EC2 instance as soon as I figure this thing out. I thought the elastic IP would solve things but it hasn't

  Read the article

• How to place additional access-restrictions on a subdirectory in Apache?

  - by Mikhail T.

  We have a list of "internal" IP-addresses and only allow access to the server (Location /) from that list: <Location /> Require ip x.x.x.x Require ip y.y.y.y </Location> I need to further restrict access to a sub-directory (Location /foo) to authenticated users (Require valid-user). Whatever I do, I never get prompted for login to access /foo -- Apache simply grants me access, because my IP-address is on the list (for Location /). I cycled through all three different values of AuthMerging (off, and, or) to no avail... Must be something really stupid :-/ Using httpd-2.4.6. Thank you!

  Read the article

• Mac OS X: pushing all traffic through a VMWare VM

  - by bj99

  I want to set up an Astaro (Sophos) UTM in a Virtual Machine. The Setup should be at the end the following: Cable Modem (one IP adress) | [Ethernet] Sophos UTM (running as VM [VMWare Fusion 5] on the MacMini) | [WIFI] Airport Express v2 (for sharing Local Network to wireless and wired clients) 1)| [WIFI] 2)| [Ethernet over Thunderbolt Ethernet Adapter]* Clients MacMini (Local File Server) *To have the Mini also protected behind the UTM So the setup process for the UTM works fine, but then the problems start: I just have one external IP (from my cable modem provider)== So if I put the VM in briged mode my Internet connection drops, because the MacMini also has its IP adress. If I put the VM to NAT mode the Mini itself is not protected by the UTM So: is there a way to hide the en0 interface(Ethernet) and the en1 interface (Wifi) from the MacMini, so that they not even appear in System Preferences Network section but are available to the VM? That way the Mini must connect to the en2 interface (Thunderbolt adapter) to make any Internet/LAN connection and I just use the given single IP from the Cable Modem. Thaks for any suggestions... Sebastian

  Read the article

• What is automatic service location on the network?

  - by Roman

  I know that zeroconf does automatic service location on the local network. But what does it mean? For example there is a printer (printing is the service that it does). This printer choose randomly an IP for itself. It asks other devices if this IP is already occupied. If not, the printer occupies this IP. Then printer says to "everybody" that "printing" service is associated with this IP. Is it "automatic service location"? Or I got something wrong?

  Read the article

• Utilize two gateways on the same network same interface with load balancing

  - by RushPL

  My setup is two ISPs on a single interface and single network. I can either set my default gateway to 192.168.0.1 or 192.168.1.250 and either work. My desire is to utilize both of them with some load balancing. I have tried to follow the advice given in here http://serverfault.com/a/96586 #!/bin/sh ip route show table main | grep -Ev '^default' \ | while read ROUTE ; do ip route add table ISP1 $ROUTE done ip route add default via 192.168.1.250 table ISP1 ip route add default via 192.168.0.1 table ISP2 iptables -t mangle -A PREROUTING -j CONNMARK --restore-mark iptables -t mangle -A PREROUTING -m mark ! --mark 0 -j ACCEPT iptables -t mangle -A PREROUTING -j MARK --set-mark 10 iptables -t mangle -A PREROUTING -m statistic --mode random --probability 0.5 -j MARK --set-mark 20 iptables -t mangle -A PREROUTING -j CONNMARK --save-mark Now then I do "traceroute somehost" repeatedly I can only get route through my default route which is 192.168.1.250. Shouldn't the packets change routes in a random manner? How to debug it?

  Read the article

• How do I run both Tomcat and PHP on Linux on port 80?

  - by Michael Gaylord

  I would like to host both Tomcat and PHP on port 80 on Linux and I have 2 IP addresses available. I am only using PHP so that I can host some mailing list software, I can map it to newsletter.mydomain.com. So my question is, is it possible to run Tomcat on port 80 on 1 IP address and Apache on port 80 on another IP address?

  Read the article

• how're routing tables populated?

  - by Robbie Mckennie

  i've been reading "tcp/ip illustrated" and i started reading about ip forwarding. all about how you can receive a datagram and work out where to send it next based on the desination ip and your routing table. but what confused me is how (in a home network setting) the table itself is populated. is there a lower layer protocol at work here? does it come along with dhcp? or is it simply based on the ip address and netmask of each interface? i do know (from other books) that in the early days of ethernet one had to set up routing tables by hand, but i know i didn't do that.

  Read the article

• Issue Connecting two home networks

  - by Alex

  Hi, I have a home networking question. I have two DLINK wireless/wired routers in my house, connected to the Internet ISP. There are a 2 computers on each of the two networks. Network1: has 192.168.0.0 (gateway) Valid IP'S range - 192.168.0.1 - 192.168.0.10, with COMP1 having a fixed IP of 162.168.0.1 Network2: has 192.168.0.100 (gateway) Valid IP'S range - 192.168.0.101 - 192.168.0.110 with COMP2 having a static IP of 162.168.0.101, a WIRELESS printer on 192.168.0.102 Both routers have a netmask of 255.255.255.0 My need is to connect the two routers, so that I can Remote desktop for COMP1 to COMP2 and viceversa, and COMP1 to connect to the wireless printer on Network2. can anyone help to set this up so that the both networks can talk to each other. Any help is appreciated. -Alex

  Read the article

• Port forwarding not working properly

  - by sudo work

  I'm trying to host a small web server from my home network; however, I have not been able to successfully port forward ports to the local server. My current network topology looks like this: Cable Modem/Router - Secondary Wireless Router - Many computers (including server) The modem/router I'm using is a Cisco (Scientific Atlantic) DPC2100, provided by my ISP. The wireless router that I'm using as the central hub to my home network is a Linksys E3000. The computer being used as a server is running Ubuntu 10.04 Server Edition. The main issue is that I can't access the server remotely, using my WAN IP address. I have port forwarded my wireless router; however, I believe that I need to somehow set my modem to bridge mode. As far as I can tell though, this isn't possible. Here are the various IP address settings: DPC2100 WAN: 69.xxx.xxx.xxx Internal IP: 192.168.100.1 Internal Network: 192.168.7.0 E3000 IP Address: 192.168.7.2 Gateway: 192.168.7.1 Internal IP: 192.168.1.1 Internal Network: 192.168.1.0 Server IP Address: 192.168.1.123 Gateway: 192.168.1.1 Now I can do an nmap at various nodes, and here are the results (from the server): nmap localhost: 22,25,53,80,110,139,143,445,631,993,995,3306,5432,8080 open nmap 192.168.7.2: 22,25,80 (filtered),110,139,445 open (ports I have forwarded in the E3000)* nmap 69.xxx.xxx.xxx: 1720 open *For some reason, I can SSH into the server at 192.168.7.2, but not view the website. Here are also some other settings: /etc/hosts/ 127.0.0.1 localhost 127.0.1.1 servername ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters /etc/apache2/sites-available/default snippet <VirtualHost *:80> DocumentRoot /srv/www/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> ... </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> ... </Directory> ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> ... </Directory> </VirtualHost> Let me know if you need any other information; some stuff probably slipped my mind.

  Read the article

• Connect to remote MySQL using proxy

  - by hypeflow

  I'm trying to connect to a remote MySQL server (with TCP access limited to a specific IP) using port forwarding via SSH, but still haven't figured out how to do it. Here's what I intend to do: Local[A] ---> Proxy[B] ---> Remote MySQL[C] [A] Local machine with Windows [B] CentOS machine with IP 123.123.123.1 (with it's own MySQL running, btw) [C] Remote MySQL server with IP 123.123.123.1 authorized on port 3306 How to achieve this? Thanks in advance.

  Read the article

• SSH: Configure ssh_config to use specific key file for a specific server fingerprint

  - by Penthi

  I have a key based login for a server. The IP and DNS of the server can change, because it is hosted on Amazon. Is there a way to configure the ssh client config to use the specific key file for this server only, when the fingerprint of the server matches? In other words: Normaly servers are matched by IP or DNS in the ssh client config. I want to do this by fingerprint, becaus IP and DNS can change.

  Read the article

• Cisco ASA - NAT'ing VPN traffic

  - by DrStalker

  I have an IPsec VPN setup like this: [Remote users]-[Remote ASA] <-VPN-> [My ASA]-[Subnet A]-[Router 2]-[Subnet B] The VPN is set to handle traffic between [remote users] and [Subnet A]; it does not include [Subnet B]. Pretend the firewall rules for all routers are to permit everything. Now I want to redirect traffic that comes over the VPN to a specific IP on [subnet A] (192.168.1.102) to an IP on [Subnet B] (10.1.1.133) If I add a rule on [My ASA] to NAT traffic to original IP 192.168.1.102 to new IP 10.1.1.133, 1) Will this affect the connections coming in over the VPN? (ie: the VPN packets are unencrypted and then NAT is applied) 2) Will this work when the post-NAT target is on Subnet-B, which is not part of the VPN traffic selection?

  Read the article

• Is my website running on an iPhone?

  - by Stefano Borini

  Provocative question, but in any case, this is what it would appear... unless there's some other reason, of course. In my cystat wordpress log, I obtained the following entry IP Browser OS Date Method Type URL 127.0.0.1 Safari 419.3 iPhone July 30, 2009 7:39 pm GET BLOG /blog/ The IP address is the IP of the visiting client. It's clear that this is not possible. Why do I get 127.0.0.1 as IP? cystat bug? some weird network trick I am not aware of? or is my website really running on an iPhone, and the guy at the applestore is reading my blog ?

  Read the article

• ipconfig /release not working, why?

  - by barlop

  ipconfig /release is not working, why is that? here is a sequence where I put my cable in get an IP, try ipconfig /release and it tells me it can't release wireless, but there is no wireless connection. i'm just trying to release the wired one. C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Fine so I plug my cable in C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 0.0.0.0 Subnet Mask . . . . . . . . . . . : 0.0.0.0 Default Gateway . . . . . . . . . : C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.1.8 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.254 Fine so from above, it clearly has an iP C:\>ipconfig /release Windows IP Configuration No operation can be performed on Wireless Network Connection while it has its me dia disconnected. C:\>

  Read the article

• Connecting/Adding a private network on windows server 2008

  - by WhyMe

  Hey all, I have a dual server configuration on a host provider using VPS. I was told by my Host provider that in order to use free bandwidth between my two servers (they are in the same location) I need to add a alias "subnet" to a specific ip (A private network, VPN). How do I add an aliased ip in widnwos? in Linux the relevant command is supposed to be (By my search in blogs) "ifconfig eth0:1 10.129.175.165 netmask 255.255.255.0" They also said that another way to connect between the servers (should also be faster) is to use "private lan", but as it happens I don't know how to define one :(. Is there a windows equivalent or another way to do this? I have checked my ip config and found no indication of the private lan or the VPN ip.

  Read the article

• Adding subnet to a vsphere with single vcenter and esxi host

  - by Ilya Rakhlin

  Let me start of by saying that I do not specialize in networking, I am in the process of adding additional VMs to a testing environment and wanted some recommendations. In this case I am running a single ESXI 5.1 host and a single Vcenter management server. The problem is, I need another range of IP addresses added to the existing setup; hopefully without reconfiguring everything. Currently the esxi host is configured to IP: 192.168.100.200, gateway: 192.168.100.1 and subnet: 255.255.255.0. All of the VMs are running some version of linux with hard coded IP addresses in that range, and using that subnet. The VMs I am about to deploy I want to be on the 192.168.101.X network. Is it possible to add an additional subnet to this existing system that will also communicate with the current subnet? The esxi host has 6 physical NICs but only one connected as it is only a testing system; not sure if that matters. Are there any other ways to accomplish this hopefully without restarting or at least reconfiguring the IP addresses for each VM? Reason: Due to the configuration of the VMs to run the applications that we need I am using a large amount of the current IPs in the potential range (mostly VIPs). I will be setting up a new version of this “environment” while keeping the old one, thus potentially running out of IP addresses.

  Read the article

< Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >