Search Results

Search found 13347 results on 534 pages for 'embedded device'.

Page 178/534 | < Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >

• bond0 and xen = crash

  - by Rajat

  Bonding with xen 1 - Stop all guests. Reboot dom0 after running "chkconfig xend off" and "chkconfig xendomains off". 2 - Configure bond0 by enslaving eth0 and eth1 to it. I added the below two entries to /etc/modprobe.conf. alias bond0 bonding options bond0 mode=6,miimon=100 Content of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none Content of /etc/sysconfig/network-scripts/ifcfg-eth1 DEVICE=eth1 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none Content of /etc/sysconfig/network-scripts/ifcfg-bond0 DEVICE=bond0 IPADDR= NETMASK= ONBOOT=yes BOOTPROTO=static USERCTL=no Did "modprobe bond0" and "service network restart" after that. 3 - Edit /etc/xen/xend-config.sxp Change (network-script network-bridge) To (network-script 'network-bridge netdev=bond0') 4 - Start xend. "service xend start". 5 - chkconfig xend on. 6 - modprode bond0 7 - more /proc/net/bonding/bond0 8 - Create guest images as usual and bridge it to xenbr0. about config i did for my xen kernel rhel 5.3 after i reboot the host server i get in place bond0 get pbond0 and its get disconnect from network only i ping to my vm's on the host server any one have any idea why xen bond0 is acting like that or what is solutions to come out of pbond0 to bond0.

  Read the article

• Auto-rebuild RAID6 with MDADM

  - by user65632

  Hello everybody, i'm new in this forum, and because I see that a lot of people get helped here, i'll ask my question here! I have a openSUSE 11.3 Linux computer with 5 disks of 1TB (WD enterprise disks) in it. with mdadm I configured an RAID6 device. Now, after a lot of thorough testing, i've noticed that when the computer goes down unsuspectedly it could happen (1 time out of 10) that while booting, the md0 device isn't recognised, and then the machine goes in "recovery mode", which means that i have to 'CTRL + C' it so it can boot to openSUSE. Once in openSUSE i have to readd the drive manually with 'mdadm /dev/md0 --add /dev/sdX'. After this everything works back fine (after resynching). So my question is: Is there a way to auto-rebuild the RAID6 device when there are problems? and how can I stop this "recovery mode" from happening. Because the computer will be in a place I can't go to, to connect a keyboard, 'CTRL + C' it just to get in openSUSE. If you could help me, I would be a very very very! happy man! :-) thanks in advance! Mikhail

  Read the article

• CUPS causes printer to click and doesn't print

  - by Pez Cuckow

  I'm suffering a strange problem with my Cannon iP4850 when trying to use CUPS on a Raspberry Pi (this is not RPi specific, please do not vote to move it). When I plug the printer into my Laptop (OSX) or my Desktop W7 it identifies as a iP4800 and prints perfectly. So I plug it into the Pi (running debian), set it up in CUPS enable sharing and can now see the iP4800 series shared on the network. However if I print to it (using AirPrint etc...); the file gets to CUPS safely (shows in the queue) but when it tries to print the printer clicks (like a loud thunk) 3/4 times and then gives in, with a double amber flashing light. In cups it shows as job completed. Do you know why using the pi and cups would cause what appears to be a hardware fault and what I can do to fix the problem or to provide further debug info? Thanks for your time! Description: Canon iP4800 series Location: Lounge Driver: Canon PIXMA iP4800 - CUPS+Gutenprint v5.2.9 (color, 2-sided printing) Connection: usb://Canon/iP4800%20series?serial=2239B2 Note: I've tried deleting and re-adding the printer to the Laptop, Desktop and PI and the results are always the same Log for plugging in printer and printing (attempting to) something until the printer turned off again pi@pezpi /var/log $ dmesg [ 7284.176336] usb 1-1.2: new high speed USB device number 8 using dwc_otg [ 7284.279703] usb 1-1.2: New USB device found, idVendor=04a9, idProduct=10d5 [ 7284.279750] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7284.279771] usb 1-1.2: Product: iP4800 series [ 7284.279786] usb 1-1.2: Manufacturer: Canon [ 7284.279800] usb 1-1.2: SerialNumber: 2239B2 Setting cups to verbose: Change loglevel in cupsd.conf to debug (or debug2) pi@pezpi /var/log $ sudo vim /etc/cups/cupsd.conf pi@pezpi /var/log $ sudo /etc/init.d/cups restart [ ok ] Restarting Common Unix Printing System: cupsd. pi@pezpi /var/log $ Log from $ /var/log/cups/error_log is at http://pastebin.com/7VZMRMrG (too large to post here) The log contains - in order (deleted the log and then did the beneath) Restarting the cups server Attempting to print a test page x2 Printing from 192.168.1.90 via AirPrint Printing from 192.168.1.90 via Network Print Turning the printer off and on again

  Read the article

• Cisco Spam Blocker, Iron Port, Lotus Domino, Integration Help

  - by NickToyota

  Hi serverfault universe, I work for a medium sized (roughly 200 user) company. We are attempting to intagrate our new Cisco Spam Video Blocker (ironport) device into our network so that it acts as an incoming filter then passes it off to our Lotus domino mail server. And also vise versa. The way our network is setup currently has an mx record pointing to our Domino mail SMTP incoming server which is currently setup to be an inbound gateway and filter (using symantec domino mail software). We want to replace the inbound gateway with the ironport. Our company has also invested in a pool of external IP addresses which I believe has been currently assigned to our web, email, servers. What would the proper course of action be to successfully integrate the device be? Mx record change? Replace the domino gateway completely with the ironport? We attempted to set the ironport device to the external IP of what our mx record is pointing to without much success. Any help on proper setup would be greatly appreciated.

  Read the article

• Raid1 with active and spare partition

  - by Daniel Baron

  I am having the following problem with a RAID1 software raid partition on my Ubuntu system (10.04 LTS, 2.6.32-24-server in case it matters). One of my disks (sdb5) reported I/O errors and was therefore marked faulty in the array. The array was then degraded with one active device. Hence, I replaced the harddisk, cloned the partition table and added all new partitions to my raid arrays. After syncing all partitions ended up fine, having 2 active devices - except one of them. The partition which reported the faulty disk before, however, did not include the new partition as an active device but as a spare disk: md3 : active raid1 sdb5[2] sda5[1] 4881344 blocks [2/1] [_U] A detailed look reveals: root@server:~# mdadm --detail /dev/md3 [...] Number Major Minor RaidDevice State 2 8 21 0 spare rebuilding /dev/sdb5 1 8 5 1 active sync /dev/sda5 So here is the question: How do I tell my raid to turn the spare disk into an active one? And why has it been added as a spare device? Recreating or reassembling the array is not an option, because it is my root partition. And I can not find any hints to that subject in the Software Raid HOWTO. Any help would be appreciated.

  Read the article

• MicroSD card isn't detected by computer, apparently usable only with phone

  - by paulcjoubert

  I have a 4GB MicroSD card that apparently only works (in the sense that the device detects and can read and write from and to the card) with my old Nokia XpressMusic 5800 phone. I have taken pictures and recorded voice notes that were saved on the card. These are accessible after the card has been removed, which tells me that the problem isn't with the card. The card could also not be locked to the phone as it would at least be detected by a computer and it would be able to write raw data to it with dd, such as /dev/zero. Also, the card is not the Nokia card that came with the phone and I have done nothing that would have caused it to be locked. (I could not find anything on Nokia's website that helps, but then again... my search was not THAT thorough.) The card works on no other device that I have tried so far. I have tried it in my Canon camera (through an adapter), but it refuses to even boot with the card inserted. My card reader (via USB cable and hub) is detected as /dev/sdx with or without the card inserted. When trying to access the card I get an "No medium found". dmesg does not report any change at all when inserting and removing the card. I would obviously like to use my card on other devices - the phone is quite old - and even a likely explanation would help. Thankyou in advance! EDIT 1: I can use the card by connecting the phone to my computer, but this is impractical and would not allow me to use the card in any other device. EDIT 2: The data on the card is not important to me at all.

  Read the article

• hp proliant dl360 disk diagnostic issue

  - by user1039384

  We recently got two used drives (15000) and installed on our HP proliant dl360 G5 server. Created RAID1 and used HP SmartStart CD to perform diagnostics. Interestingly, the Diagnostic tab immidiately fails on Logical drive testing saying the Disk1 should be replaced, while the Test tab successfully runs all the complete tests on both disks and does not find any issue. At the meantime, when booting to esxi 5, vSphere periodically shows the Disk1 as Unknown and Logical drive in recovery process. This happens every 5-10 minutes. Here is the log from HP SmartScan diagnostic: 1 - Device, Test: Logical Drive 1, Storage Controller in Slot 0 1 - Description: The controller has reported a critical error in the drive error log. 1 - Recommended Repair: This drive should be replaced. 1 - Failed Count: 44 1 - Error code: F157 There is also another error log record (see below): 2 - Device, Test: test_components/libstorage.so ID 2 - Description: An unexpected exception occurred while performing an operation. Exception message: CISS_StatusHandler::evaluate: commandStatus = 4 (INVALID); hexdump of CISS_ErrorInfo: 00000000: __ __ 04 __ 20 __ __ __ __ __ __ __ __ __ __ __ .... ... ........ 00000010: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ 00000020: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ Device: Hard Drive 2, Storage Controller in Slot 0 Property name: Bad Target Count 2 - Recommended Repair: Reboot or restart Insight Diagnostics. Retry the test. If the problem persists, upgrade to the latest version of Insight Diagnostics. 2 - Failed Count: 48 2 - Error Code: F62 Note that rebooting didn't help and I was running the latest diagnostic software version. Anyone has a clue? Is this a real disk issue? BTW, the controller is Smart Array E200i Thanks in advance

  Read the article

• DVD drive won't work after installing software

  - by Dan

  DVD drive was already region-free but for some reason would not play a certain DVD as it was the "wrong region". This is the first time I've played a DVD on the drive, but I've imported a lot of CDs before and they always worked fine, even CDs bought from the USA (I live in the UK). To get around this, I downloaded a piece of software called "DVD Region Killer". (Clicking the link won't start the download, so go ahead and check it.) After this, the drive isn't recognised. It won't show up in "My Computer", and when I insert a disc it will start to whir but not take action, i.e. iTunes won't recognise that I have put a CD in. In the Device Manager, the drive shows up with a caution-sign. The device status reads: Windows cannot start this hardware device because its configuration information (in the registry) is incomplete or damaged. (Code 19) Disabling, uninstalling and reinstalling does not help. Clearly the software download is the issue, but it is difficult to remove. The only files I can find in Program Files are: C:\Program Files (x86)\Elaborate Bytes\DVD Region Killer which contains a changelog and a HTML document which has no info on uninstalling. It doesn't show up on "Add or Remove Programs", or even as a background process when I press ctrl-alt-del. Apparently it has no interface as such, and can be accessed by an icon in the system tray, (see review in link) but I don't see the icon. If it helps to know, I have a Dell Inspiron running Windows 8 64-bit, and the model of the DVD drive is: MATSHITA DVD+-RW UJ8C2 Thanks in advance.

  Read the article

• SQL Server Offsite Backups

  - by Eric Maibach

  We have about !TB of SQL Server databases, and these databases generate about 200GB of data changes each day. Up to this point we have been doing Weekly full backups, daily diff backups, and hourly transaction log backups. The full and diff backups are backed up to tape and taken offsite each day. We have been trying to move away from tapes, and our IT department purchased a Barracuda Backup device that backups up data and then sends it offsite using our internet connection. I have been trying to get this to work for our SQL Server backups, and have ran into a number of problems. I normally like to just use SQL Server to perform backups instead of trying to use a agent, so that is what I tried first. However the Barracuda device was not able to dedup these files very well, so it ended up being to much data to try to send offsite and to archive. I then tried installing the Barracuda agent and using it to backup the SQL Server databases. However the problem I am having there is that on some of the database servers I also have files that need backed up, and I cannot find a way to create seperate backup schedules for the file backups and the SQL Server backups. Barracuda only does full or transaction log backups. So if I want to do hourly transaction log backups I end up doing a file system backup every hour (which is not good), or if I only schedule the backups to run once a night I either have to do a full backup every night, or only do a transaction backup once a day. None of these scenarios are good options. My question is, how is everyone else getting their large SQL Server database backups offsite. Are you just using tape, or have you found a offsite backup device that works well? Is anybody else using Barracuda to backup their SQL Server databases? If you do, then how do you have it setup?

  Read the article

• Need help with local network printing while using VPN on Ubuntu 10.10 desktop

  - by MountainX

  I can print to my HP printer via the LAN when I'm not connected to the VPN. When connected to the VPN, printing fails. OpenVPN 2.1.0 x86_64-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Jul 12 2010 I can ping the printer while connected to the VPN: $ ping 192.168.100.12 PING 192.168.100.12 (192.168.100.12) 56(84) bytes of data. 64 bytes from 192.168.100.12: icmp_req=1 ttl=255 time=9.17 ms --- 192.168.100.12 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss... $ ping HpPrinter.local PING HpPrinter.local (192.168.100.12) 56(84) bytes of data. 64 bytes from HpPrinter.local (192.168.100.12): icmp_req=1 ttl=255 time=0.383 ms --- HpPrinter.local ping statistics --- 4 packets transmitted, 4 received, 0% packet loss... But here's the error when I try to print while connected to the VPN: hpijs[9990]: io/hpmud/jd.c 784: mdns lookup HpPrinter.local retry 1... ... hpijs[9990]: io/hpmud/jd.c 784: mdns lookup HpPrinter.local retry 20... hpijs[9990]: io/hpmud/jd.c 780: error timeout mdns lookup HpPrinter.local hpijs[9990]: io/hpmud/jd.c 88: unable to read device-id hp[9982]: io/hpmud/jd.c 784: mdns lookup HpPrinter.local retry 1... ... hp[9982]: io/hpmud/jd.c 784: mdns lookup HpPrinter.local retry 20... hp[9982]: io/hpmud/jd.c 780: error timeout mdns lookup HpPrinter.local hp[9982]: io/hpmud/jd.c 88: unable to read device-id hp[9982]: prnt/backend/hp.c 745: ERROR: open device failed stat=12: hp:/net/Officejet_Pro_L7600?zc=HpPrinter I am running iptables rules, but the problem doesn't appear related to the firewall. I've tested with no rules (i.e., no firewall). The printing problem happens when the VPN is connected. I can guess it is an mdns problem, but searching google about mdns didn't turn up anything that seemed related to this (at my level of knowledge). Any suggestions?

  Read the article

• Timeout option not working on efi windows 7/windows8 dual boot machine

  - by Guenter

  I hav a gigbyte GA-Z77m-D3h mobo and installed Windows 8 Pro and Windows 7 Ultimate on two SSDs (in that order) in EFI mode. Now when I start my computer, I get the windows boot menu (text mode) with the two OSses to choose, but I have to manually press RETURN to have the computer boot into the Win OS. Even if I wait an hour, no default action takes place. Using bcdedit (from either of the OSses) I can successfully change the time out value, and it shows up in the bcdedit (no params) output. But it doesn't fire ... Here is my current BCDEdit output (headers are in German, but values should be readable): Windows-Start-Manager --------------------- Bezeichner {bootmgr} device partition=O: path \EFI\Microsoft\Boot\bootmgfw.efi description Windows Boot Manager locale de-DE inherit {globalsettings} integrityservices Enable default {default} resumeobject {5ad2802c-c60a-11e2-acdb-80331c501b11} displayorder {default} {current} {5ad2802a-c60a-11e2-acdb-80331c501b11} {5ad28028-c60a-11e2-acdb-80331c501b11} {5ad28029-c60a-11e2-acdb-80331c501b11} toolsdisplayorder {memdiag} timeout 5 displaybootmenu Yes Windows-Startladeprogramm ------------------------- Bezeichner {default} device partition=W: path \Windows\system32\winload.efi description Windows 7 locale de-DE inherit {bootloadersettings} recoverysequence {5ad2802e-c60a-11e2-acdb-80331c501b11} recoveryenabled Yes osdevice partition=W: systemroot \Windows resumeobject {5ad2802c-c60a-11e2-acdb-80331c501b11} nx OptIn Windows-Startladeprogramm ------------------------- Bezeichner {current} device partition=C: path \Windows\system32\winload.efi description Windows 8 locale de-DE inherit {bootloadersettings} recoverysequence {5ad28033-c60a-11e2-acdb-80331c501b11} integrityservices Enable recoveryenabled Yes isolatedcontext Yes allowedinmemorysettings 0x15000075 osdevice partition=C: systemroot \Windows resumeobject {5ad28031-c60a-11e2-acdb-80331c501b11} nx OptIn bootmenupolicy Standard hypervisorlaunchtype Auto (this output is from Win8; the Win7 looks nearly identical) If maybe the problem comes from a bad EFI Windows boot manager installation, can this be fixed without loosing my windows installations?

  Read the article

• Un-install network printer drivers from Win7 64 Home Premium

  - by AkkA

  I recently bought a NAS device that has print server functionality through USB. The printer was already installed and fully working on another Win XP box, set up that box to see the printer over the network and it prints fine. I tried to install the printer on my Win7 laptop (64 bit, Home Premium), but got the wrong drivers somehow, or it just refuses to work. I need to completely un-install the printer drivers and start from scratch. Removing the printer (by going to the printers folder, right click and remove) does not actually un-install the drivers. It only removes the printer from active use. Even if I try to re-install new drivers it will load the old ones. I have read a few things on the net that say to load up a device snap-in or something of the sort into Computer Management, but this seems to be valid for Win7 Pro or greater, the function everyone tells you to use isnt available in Home Premium. Is there anything I can use to manage device driver files in Home Premium? I want to completely remove them from the computer.

  Read the article

• Which type RAM support Our Servers?

  - by Mikunos

  I need to increase the RAM in our DELL servers but with the lshw I cannot see if the RAM installed is a UDIMM or RDIMM. Handle 0x1100, DMI type 17, 28 bytes Memory Device Array Handle: 0x1000 Error Information Handle: Not Provided Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: DIMM_A1 Bank Locator: Not Specified Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz (0.8 ns) Manufacturer: 00CE00B380CE Serial Number: 8244850B Asset Tag: 02103961 Part Number: M393B5773CH0-CH9 Handle 0x1101, DMI type 17, 28 bytes Memory Device Array Handle: 0x1000 Error Information Handle: Not Provided Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: DIMM_A2 Bank Locator: Not Specified Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz (0.8 ns) Manufacturer: 00CE00B380CE Serial Number: 8244855D Asset Tag: 02103961 Part Number: M393B5773CH0-CH9 Handle 0x1102, DMI type 17, 28 bytes Memory Device Array Handle: 0x1000 Error Information Handle: Not Provided Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 2 Locator: DIMM_A3 Bank Locator: Not Specified Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz (0.8 ns) Manufacturer: 00CE00B380CE Serial Number: 8244853E Asset Tag: 02103961 Part Number: M393B5773CH0-CH9 how have we do to know which is the right RAM memory to buy? thanks

  Read the article

• Streaming music throughout the house on a budget?

  - by greggannicott

  I was wondering whether anyone knew of a way to stream music throughout a house on a budget? I want to avoid spending any money on this (eg. I don't want to buy a d-link style device). It would be ideal if I could use my existing hardware and some open source software. I have three old(ish) PCs knocking around. I'm happy to stick either Windows or Linux on them. They can all be hooked up to speakers. The ideal solution would result in: the same audio being heard from every device (eg. when you hear a beat on one device, you'd hear it at the exact same time on another (so you don't get any echo)) I'd be able to control the source application (eg. the songs lined up) with my iPhone. I realise I'm being cheeky with those two wishes - but you never know your luck. Am I asking for too much, or is there a piece of software/protocol out there with this purpose in mind? I've been searching for sometime now, but haven't had any joy. Thanks in advance.

  Read the article

• Fix bad superblock on logical partition

  - by Chris

  I was following http://www.howtoforge.com/linux_resi...xt3_partitions and when i reboot and run: root@Microknoppix:/home/knoppix# fsck -n /dev/sda7 fsck from util-linux-ng 2.17.2 e2fsck 1.41.12 (17-May-2010) fsck.ext2: Superblock invalid, trying backup blocks... fsck.ext2: Bad magic number in super-block while trying to open /dev/sda7 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> so i ran e2fsck with all the block numbers that you need (forget exactly what tool i used to find where the superblocks are hidden) no dice then i ran testdisk and had it look for the superblock, no results anyone have any ideas? fdisk -l for reference: root@Microknoppix:/home/knoppix# fdisk -l Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x97646c29 Device Boot Start End Blocks Id System /dev/sda1 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 38912 312046593 f W95 Ext'd (LBA) /dev/sda5 64 326 2104320 82 Linux swap / Solaris /dev/sda6 * 327 2938 20972544 83 Linux /dev/sda7 2938 38912 288968672+ 83 Linux To be honest it looks like I lost it... Next step if that happens is to dump the partition to an image file and hope i can find or write some software to parse through the data looking for known file headers, i think.

  Read the article

• Why does my Intel Tolapai network chip not transmit packets?

  - by Hanno Fietz

  I'm trying to deploy an embedded system (NISE 110 by Nexcom) based on the Intel EP80579 (Tolapai) chip. Tolapai apparently integrates controllers for Ethernet etc. on a single chip (Intel homepage). The machine can't get a network connection. Diagnosis as far as I could manage: Drivers drivers from Intel compiled and installed without problems (version 1.0.3-144). Kernel version and Linux distribution (CentOS 5.2, 2.6.18) match the driver's installation instructions. drivers are loaded and show up in lsmod (module names are gcu and iegbe) interfaces eth0 and eth1 show up in ifconfig ifconfig I can bring up the interfaces with fixed IP pinging the interface locally works ifconfig shows flag UP but not RUNNING Link ethtool shows "Link detected: no", "Speed: unknown (65536)" and "Duplex: unknown (255)" Link LED is on on the other side of the cable, ethtool shows "Link detected: yes" and reports a speed of 1000 Mbps, which has allegedly been auto-neogotiated with the problematic device. Network traffic analysis the device does not reply on ARP, ICMP echo or anything else (iptables is down) when trying to send ICMP or DHCP requests, they never reach the other end activity LED is off on the device, on at the other end. I tried the following without any effect: Different cables (2 straight, one crossed), I get the link LED lit up on each. Three different devices on the other end (one PC, one netbook, one router) Fixed ARP table entries on both sides Connecting both network ports of the machine with each other, won't ping through the cable, but will ping locally. Tried straight and crossed cables for that.

  Read the article

• D-LINK DIR-615 router keeps giving my wireless devices bad ip addresses

  - by mlsteeves

  I have a D-LINK DIR-615 router, and wired devices have no problem getting an IP, however; wireless devices end up with a 169.254.. address (subsequently, they cannot access the internet through the router). I have removed all wired connections from the router, so there is no other dhcp server running. I've also gone back to the store, and replaced it with another, thinking that maybe it was defective. According to the router, it gave 192.168.0.101 to the wireless device. According to the wireless device it got 169.254.67.71. I've tried both a laptop and an iPod Touch, both exhibit the same behaviour. Has anyone seen this type of behaviour, or have any ideas of stuff to try? NEW INFORMATION I looked at the logs on the router, and when the wireless device tries to connect, this is what is logged: Sep 10 18:13:39 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:31 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:26 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:23 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:21 UDHCPD sending OFFER of 192.168.0.111 I connected a computer directly to the router, and here is what it looks like: Sep 10 18:14:18 UDHCPD Inform: add_lease 192.168.0.110 Sep 10 18:14:14 UDHCPD sending ACK to 192.168.0.110 Sep 10 18:14:14 UDHCPD sending OFFER of 192.168.0.110 Not sure if that helps or not.

  Read the article

• Driver denied access to PCI card

  - by Corin

  Alright, I asked this on StackOverflow (here) and they suggested trying ServerFault to get help on permissions. So here's the deal. We designed a custom PCI card and wrote the driver for it. It's been working for years without problems but now we encountered one particular installation were it doesn't work. The problem is that we cannot connect to the PCI to begin communication with it. We tried replacing the card and had the same problem. We had the motherboard replaced thinking the PCI slots were bad. That didn't help either. We tried the cards in a different computer and they all worked. So it seemed to be something specific to the computer. The Windows Device Manager indicates the device is working properly and seems to have all the correct driver info. We now have this troublesome computer back at the office for testing. With the help of some extra debug info in the driver we determined that we cannot connect because access is denied. Sounds like a permissions issue to me. I should note that we are logged into the system as a local administrator. So what configuration option in Windows can prevent access to a device?

  Read the article

• How can I update generic non-pnp monitor?

  - by njk

  Background I've been running a KVM switch with my monitor at 1920 x 1080 over VGA for over a year. Did a Windows Update on 12/11/12 which did the following: Update for Windows 7 for x64-based Systems (KB2779562) Security Update for Windows 7 for x64-based Systems (KB2779030) Cumulative Security Update for Internet Explorer 8 for Windows 7 for x64-based Systems (KB2761465) Windows Malicious Software Removal Tool x64 - December 2012 (KB890830) Security Update for Windows 7 for x64-based Systems (KB2753842) Security Update for Windows 7 for x64-based Systems (KB2758857) Security Update for Windows 7 for x64-based Systems (KB2770660) After a restart, my extended monitor was dark. I attempted to reset the extended display configuration, and noticed my monitor was being detected as a Generic Non-PnP Monitor: I uninstalled, downloaded new, and re-installed display drivers. Nothing. I attempted to unplug my monitor from the power for 15 minutes. Nothing. I followed some of the suggestions on this thread; specifically DanM's which suggested to create a new *.inf file and replace that in Device Manager. Device Manager said the "best driver software for your device is already installed". The only thing that works is when the monitor is directly attached to the laptop. This obviously is not what I want. My thought is to somehow remove the Generic Non-PnP Monitor from registry. How would I accomplish this and would this help? Any other suggestions? Relevant Hardware ASUS VE276 Monitor TRENDnet 2-Port USB KVM Switch (TK-207K) HP Laptop w/ ATI Radeon HD 4200 Screens

  Read the article

• Not getting IP from ISP on Multicast Network

  - by Johan Nielsen

  Im having an odd issue with my ISP (COMX.dk) I have a managed access gateway box (Telsay) with three 8P8C ports for use with Internet and Ip-Tv (respectively on different VLANS (so does my ISP tell me)) To utilize a port you will need to register your device's mac address through an online interface. You will then get your device paired with a static ip. I am using one port actively and I have registered another device (router). The router is configured to listen for an active dhcpd on the network. When my router get a lease I get a private ip 192.168.2.2 (not the one bound to my mac) which is odd! I unconnected my router from the gateway and connected my laptop directly. Same thing happened - I was given a private address. I did a port scan on the gateway and found port 80 to be open and browsed to the ip. I was then presented with a management interface of a Belkin wireless router (HMMM!!!!) <--by the way, not my gear At this point I called the ISP to let them know of my issue/findings - Only to be replied "Well, we cant see any rogue dhcp servers" (thinking to myself, well I can) I then decided that it could be fun to try the other port of my gateway, only to experience the same. So I reconnected my router and used the remaining port to make an observer(wireshark promic etc.) I am able to see my router trying to discover a dhcp server but I can also see my ISP's IGMP and PIMv2 packages just repeating the same pattern. Hello...Hello...Hello :) So I called them again, only to get the same response, "we dont see any rogue dhcp's...we cant see the host you are talking to (mac address of the Belkin router)...you are definitively connected through wireless?!?(no im not, no such thing as a wireless wire - i thought to myself)" My questions is, What is going on? (besides from what im reporting here) What am I seeing that the don't? What can I tell them in order for them to resolve mine/their issue?

  Read the article

• Driver denied access to PCI card

  - by Corin

  Alright, I asked this on StackOverflow (here) and they suggested trying ServerFault to get help on permissions. So here's the deal. We designed a custom PCI card and wrote the driver for it. It's been working for years without problems but now we encountered one particular installation were it doesn't work. The problem is that we cannot connect to the PCI to begin communication with it. We tried replacing the card and had the same problem. We had the motherboard replaced thinking the PCI slots were bad. That didn't help either. We tried the cards in a different computer and they all worked. So it seemed to be something specific to the computer. The Windows Device Manager indicates the device is working properly and seems to have all the correct driver info. We now have this troublesome computer back at the office for testing. With the help of some extra debug info in the driver we determined that we cannot connect because access is denied. Sounds like a permissions issue to me. I should note that we are logged into the system as a local administrator. So what configuration option in Windows can prevent access to a device?

  Read the article

• Failing to load rootfs: Ubuntu 10 + grub2 + rootfs ext4 w/ RAID1

  - by James

  I am having problems booting a new Ubuntu 10 (server) install. My primary HD (/dev/sda) is laid out as follows: Device Boot Start End Blocks Id System /dev/sda1 * 1 18 144553+ 83 Linux <-- /BOOT /dev/sda2 19 182401 1464991447+ 5 Extended /dev/sda5 19 2207 17583111 fd Linux raid autodetect /dev/sda6 2208 11934 78132096 fd Linux raid autodetect <-- / (ROOTFS) /dev/sda7 11935 182401 1369276146 fd Linux raid autodetect The rootfs is part of a RAID1 (software) array (currently degraded): # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md2 : active raid1 sda6[1] 78132032 blocks [2/1] [_U] The UUIDs for the partitions are as follows: # blkid /dev/sda1 /dev/sda1: UUID="b25dd301-41b9-4f4d-9b0a-0e31713dd74c" TYPE="ext2" # blkid /dev/sda6 /dev/sda6: UUID="af7b9ede-fa53-c0c1-74be-31ec752c5cd5" TYPE="linux_raid_member" # blkid /dev/md2 /dev/md2: UUID="a0602d42-6855-482f-870c-6f6ecdcdae3f" TYPE="ext4" Finally, I have my grub2 menuentry setup as follows: ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.32-25-server' --class ubuntu --class gnu-linux --class gnu --class os { insmod ext2 insmod raid insmod mdraid set root='(hd0,1)' search --no-floppy --fs-uuid --set b25dd301-41b9-4f4d-9b0a-0e31713dd74c linux /vmlinuz-2.6.32-25-server root=UUID=a0602d42-6855-482f-870c-6f6ecdcdae3f ro nosplash noplymouth initrd /initrd.img-2.6.32-25-server } When I attempt to boot, grub loads OK, however I eventually get the following error message: Gave up waiting for root device. ALERT /dev/disk/by-uuid/a0602d42-6855-482f-870c-6f6ecdcdae3f does not exist. Dropping to a shell! If from the grub bootloader I open a grub command line, I can ls (hd0,) and it lists the correct partitions with the UUIDs as shown above - sda6 shows 'a0602d42-6855-482f-870c-6f6ecdcdae3f' (the RAID UUID). If I ls (md2)/ it properly lists all the files on the RAID1 filesystem (ext4) so it doesn't appear to be an issue accessing the raid device. Does anyone have any suggestions as to what the problem might be? I can't figure this one out.

  Read the article

• Looking for a real DisplayPort hub/splitter

  - by squircle

  In my search for a new display, I came across the Dell Multi-Monitor Hub MMH11, which seemed to be an alternative to my search for daisy-chainable DisplayPort displays. However, before I cave and spend $179 on this device, I am wondering if this will be similar to other splitting devices where it appears to the computer as one big monitor and the device does the splitting (which I don't want). Or, does this use the packet-based nature of DisplayPort to present two/three separate displays to the computer? Also, would this device work on my MacBook Pro? (I know the Dell site says it's for Windows, but it also says that no driver installation is required. I'd assume since the MBP supports DP 1.2 it would work, but it's better to ask). Thanks! Edit: I've checked out the similar-looking Cirago DisplayPort splitter, but I have extreme doubts as to whether or not it's a genuine displayport splitter, or just another monitor-conglomerate. Their DVI solution looks identical to Dell's, which I'm pretty sure won't do what I want. I also don't want to order this DisplayPort "hub" and find that it doesn't do what I want it to.

  Read the article

• Unable to load Windows after using EasyBCD to Reset bcd [duplicate]

  - by johnny

  This question already has an answer here: How can I repair the Windows 8 EFI Bootloader? 9 answers My windows installation was working perfectly fine until i clicked "Reset BCD" in EasyBCD in Windows 8. After clicking that EasyBCD told me to add Win 8 entry via Add Entry Menu so i did. After restart, win 8 would not start. Neither would recovery F11. Attempts i made to Restore : Ran boot-repair from ubuntu live cd several time. Used Win8 system recovery disc created via virtualbox with win 8 preview iso. Automated repair from Win8 system recovery disc Ran following commands from cmd started from Win8 system recovery disc bootrec /fixmbr Result : Success message bootrec /rebuildbcd Result : after hitting (Y) "The requested system device cannot be found" System refresh started from Win8 system recovery disc gives error that device is locked. System reset started from Win8 system recovery disc gives error that required partition or device is missing or not accessible. Used automated repair from EasyRE disc. It gave success message. Used Fix boot problem from Macrium reflect winPE repair disc. Copied Recovery partition to usb. Booting from usb gave this error Your PC needs to be repaired. Error Code : 0XC000000f Press Enter to try again Press F8 for Startup Settings F8 & Enter does nothing I cannot install WIn7 or Win 8, error it gives : "windows cannot be installed on this disk. The selected disk is of the GPT partition style."

  Read the article

• Wired to wireless bridge in Linux

  - by adrianmcmenamin

  I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

  Read the article

< Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >