Search Results

Search found 6031 results on 242 pages for 'grid infrastructure'.

Page 178/242 | < Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >

• Cacti is ignoring hash marks in interface aliases

  - by Matt Simmons

  I'm attempting to set up Cacti to monitor a router's interfaces, and I'm having trouble getting the graph templates to show the information that I'd like. Our interface configuration looks like this: interface GigabitEthernet3/6 description WalljackNumber # Server info no ip address no shutdown switchport switchport access vlan 116 switchport mode access ip dhcp snooping trust spanning-tree portfast The "Server Info" string is really just the machine name, and a short relevant description, such as "PolarSprings vmnic2". The important part appears to be that it follows the hashmark. When I run snmpwalk, I get the proper output: IF-MIB::ifAlias.230 = STRING: WalljackNumber # Server info But in Cacti, when I go into the graph templates and set the title to this: |host_description| - Traffic - |query_ifName| (|query_ifAlias|) All that shows up in the graph is: switchname - Traffic - Gi3/6 (WalljackNumber #) Which strikes me as a little weird. What I suppose MAY be happening is that somewhere in the cacti stream, it's interpreting # as being a comment and stripping everything after, but I'm not sure. I was hoping someone could tell me that this was a known documented behavior, or that I could change it in a setting that I wasn't aware of. The alternative answer is to change the delimiter from # to something else, but I've got over a thousand lit switchports on an old college infrastructure, and I'm not sure what else might be relying on them.

  Read the article

• Self-Resetting Power Strips?

  - by Justin Scott

  We are about to deploy a number of secure kiosks into an environment where they may be prone to lightning strikes and power surges on a somewhat regular basis (southern Florida in a place where the existing electrical infrastructure is, shall we say, a bit out of date). Ideally we would use battery backups on each system, but it's not in the budget. We plan to use a standard power strip with a circuit breaker built-in to protect the computers, but management has asked if there is a power strip that can reset itself after the breaker has been tripped. I've looked around and wasn't able to find such a beast, and it seems to me that it would probably be a safety issue for such a product to exist (e.g. if something plugged into the strip is drawing a lot of current and trips the breaker, you wouldn't want that resetting itself to prevent a possible fire). Nevertheless, if anyone has experience with such a product or can point me in the direction of something that would allow the breakers to be reset automatically or remotely (we don't want to have to send someone to each kiosk every time there is a power surge) I would appreciate any tips.

  Read the article

• Load balanced IIS. Should I use NLB, or linux-based reverse proxy, or something else?

  - by growse

  What would be the best approach for load-balancing at least 2-3 Windows 2008 R2 IIS webservers running a multitude of .NET applications? My choices appear to be: 1) Hardware-based network device load balancer, like a Cisco CSS 2) Windows NLB 3) Some sort of linux based proxy, either haproxy or other The three servers sit as VMs on a vSphere farm, so I have the ability to clone to up the instance count in times of high load. I control the switch that the vSphere hosts are plugged into (Cisco 3750), but don't control the switching/routing infrastructure beyond that to the clients. (1) Is too expensive, and probably overkill for my needs. I've included this in case someone figures out a cunning way to do it on my existing network kit, which I doubt. (2) would seem to be the obvious "built-in" option, but seems to be quite fiddly messing around with network interfaces, multicast, and generally other things that seem to be needlessly complex. It's also fairly stupid, in that it can't remove hosts from the pool if they start throwing 500 errors or otherwise go wrong (3) is the most interesting option, as it would appear to offer the most flexibility and customizability, but without having to mess around with the network. However, while I'm familiar with the reverse-proxy capabilities of lighttpd etc, I'm not that well read on other options like HAProxy, which might be able to offer a lot more. Which would you go for, and is there anything I've not thought of?

  Read the article

• switching dns server providers

  - by Yoav Aner

  I'm trying to wrap my head around something that I thought I kinda understood, but clearly there's some piece missing. We're currently using Zerigo as our primary dns, with slave dns running on linode. This works quite well. However, recent DDOS attacks on zerigo meant that whilst dns queries were still resolved, we were unable to make any dns changes. Since we rely on dns changes on our own infrastructure, I'm looking to improve this somehow. I'd rather not ditch zerigo completely, and realise that this or similar problems can happen with ANY primary dns hosting provider. It might not be DDOS, but a bug on their server, or something that means we can no longer issue updates. For this I want to have some fallback option: a completely independent (primary) dns provider (maybe AWS), which we will keep in-sync manually. We will switch-over to it when there's a problem. This brings me to my question: How do I make sure we can switch those providers quickly enough? specifically, on our registrar, there's a list of name servers, but no settings like TTL etc. How do dns clients know to use the newly updated name server records? Is this configured in the SOA? However, the SOA itself is hosted with the dns provider and we might not be able to update it... This is not a question about a one-time move, which can be planned and scheduled and tested, but rather to be able to do so when things are half-broken.

  Read the article

• What can cause Powershell execution policy not to be taken into account?

  - by Stephane

  We have in our infrastructure a number of powershell scripts used for various tasks ranging from user login to support technician simulating a user context. These scripts are centralized on our file server (through DFS) for easier management. Some of them are run at logon, some are run through published Citrix applications. We have applied a policy for the whole domain and all users that sets the Powershell execution policy to "unrestricted" so that the scripts can run from the file server. This works perfectly fine for logon script (at least, so far) but for scripts that are run later (usually through a published application but the same applies when using terminal services and a full desktop), the results are inconsistent: some users can run the script fine, some are always prompted in the powershell console for letting the scripts run. I cannot find anything that could cause this behavior and it's really inconsistent: if I start powershell manually and runs get-executionpolicy, I am told that the current policy is unrestricted. Yet, if from the same session I try to run a script through a program that calls powershell <script file name> <parameters> I get prompted before the script can run. What could cause such behavior ?

  Read the article

• Feasibility of Windows Server 2008 DFS replication over WAN link

  - by CesarGon

  We have just set up a WAN link that connects two buildings in our organisation. The link is provided by a 100-Mbps point to point line. We have a Windows Server 2008 R2 domain controller on each side of the link. Now we are planning to set up DFS for file services across the organisation. The estimated data volume is over 2 TB, and will grow at approximately 20% annually. My idea is to set up a file server in each building and install DFS so that all the contents stay replicated over the 100-Mbps link. I hope that this will ensure that any user will be directed to the closest (and fastest) server when requesting a file from the DFS folders. My concern is whether a 100-Mbps WAN link is good enough to guarantee DFS replication. I've no experience with DFS, so any solid advice is welcome. The line is reliable (i.e. it doesn't crash often) and our data transfer tests show that a 5 MB/sec transfer rate is easily achieved. This is approximately 40% of the nominal bandwidth. I am also concerned about the latency. I mean, how long will users need to wait to see one change on one side of the link after the change has been made on the other side. My questions are: Is this link between networks a reliable infrastructure on which to set up DFS replication? What latency times would be typical (seconds, minutes, hours, days)? Would you recommend that we go for DFS in this scenario, or is there a better alternative? Many thanks.

  Read the article

• Conditionally Rewrite Email Headers (From & Reply-To) Exchange 2010

  - by NorthVandea

  I have a client who maintains Company A (with email addresses %username%@companyA.com) and they own the domain companyB.com however there is no "infrastructure" (no Exchange server) set up specifically for companyB.com. My client needs to be able to have the end users within it's company (companyA.com) add a specific word or phrase to the Subject (or Body) line of the Outgoing email (they are only concerned with outgoing, incoming is a non-issue in this case) that triggers the Exchange 2010 servers to rewrite the header From and Reply-To [email protected] with [email protected] but this re-write should ONLY occur if the user places the key word/phrase in the Subject (or Body). I have attempted using Transport Rules and the New-AddressRewriteEntry cmdlet however each seems to have a limitation. From what I can tell Transport Rules cannot re-write the From/Reply-To fields and New-AddressRewriteEntry cannot be conditionally triggered based on message content. So to recap: User sends email outside the organization: From and Reply-To remain [email protected] User sends email outside the organization WITH "KeyWord" in the Subject or Body: From and Reply-To change to [email protected] automatically. Anyone know how this could be done WITHOUT coding a new Mail Agent? I don't have the programming knowledge to code a custom Agent... I can use any function of Exchange Management Shell or Console. Alternatively if anyone knows of a simple add-on program that could do this that would be good too. Any help would be greatly appreciated! Thank you!!!

  Read the article

• Sonicwall NSA 240, Configured for LAN and DMZ, X0 and X2 on same switch - ping issues

  - by Klaptrap

  Our Sonicwall vendor supplied and networked the NSA240 when we required a DMZ in our infrastructure. This was configured and appeared correct although VPN users periodically dropped DNS and Terminal Services. The vendor could not resolve and so the call was escalated to Sonicwall. The Sonicwall support engineer took a look and concluded that the X0 (LAN) and X2 (DMZ) intefaces were cabled to the same switch and so this is the issue. What he observed is a ping request to the LAN Domain Controller, from a connected VPN user, is forwarded (x0) from the VPN client IP to the DC IP but the ping response from the DC IP to the VPN client IP is on X2, a copy of the log is detailed below:- 02/02/2011 10:47:49.272 X1*(hc) X0 192.168.1.245 192.168.1.8 IP ICMP -- FORWARDED 02/02/2011 10:47:49.272 -- X0* 192.168.1.245 192.168.1.8 IP ICMP -- FORWARDED 02/02/2011 10:47:49.272 X2*(i) -- 192.168.1.8 192.168.1.245 IP ICMP -- Received X0 - LAN X1 - WAN X2 - DMZ The Sonicwall engineer concluded that we either need a seperate switch for X2 or we use a VLAN switch for both. I am the companies software engineer and we have yet to have heard back from the vendor, so I am lost at sea at the moment. Do we need to buy this additional equipment or is there another configuration on the NSA240 we can use?

  Read the article

• Seizing naming master from child domain server

  - by meera

  when I am trying to seize the role from my child domain server the naming master I get the following error fsmo maintenance: seize naming master Attempting safe transfer of domain naming FSMO before seizure. ldap_modify_sW error 0x34(52 (Unavailable). Ldap extended error message is 000020AF: SvcErr: DSID-03210380, problem 5002 (UN AVAILABLE), data 8438 Win32 error returned is 0x20af(The requested FSMO operation failed. The current FSMO holder could not be contacted.) ) Depending on the error code this may indicate a connection, ldap, or role transfer error. Transfer of domain naming FSMO failed, proceeding with seizure ... Server "win-fb20ixk90mu" knows about 5 roles Schema - CN=NTDS Settings,CN=WIN-3918XHC5STU,CN=Servers,CN=Default-First-Site-Na me,CN=Sites,CN=Configuration,DC=HCL,DC=com Naming Master - CN=NTDS Settings,CN=WIN-FB20IXK90MU,CN=Servers,CN=Default-First- Site-Name,CN=Sites,CN=Configuration,DC=HCL,DC=com PDC - CN=NTDS Settings,CN=WIN-FB20IXK90MU,CN=Servers,CN=Default-First-Site-Name, CN=Sites,CN=Configuration,DC=HCL,DC=com RID - CN=NTDS Settings,CN=WIN-FB20IXK90MU,CN=Servers,CN=Default-First-Site-Name, CN=Sites,CN=Configuration,DC=HCL,DC=com Infrastructure - CN=NTDS Settings,CN=WIN-FB20IXK90MU,CN=Servers,CN=Default-First -Site-Name,CN=Sites,CN=Configuration,DC=HCL,DC=com

  Read the article

• Walkthrough/guide building aplication server for multi tenant web app [on hold]

  - by Khalid Adisendjaja

  The web app will detect a subdomain such as tenant1.app.com, tenant2.app.com, etc to identify tenant environment, each tenant environment will have a different database credential (port,db name,etc) but still connecting to the same database server. Each tenant should use app.com for their main domain, using their own domain is prohibitted. Each tenant will have their own rest api endpoint such as tenant1.app.com/api/v1/xxxx, tenant2.app.com/api/v1/xxxx, tenant3.app.com/api/v1/xxxx I've come to a simple solution by setting a wildcard subdomain (*.app.com) on webserver Apache/Nginx vhost configuration file. I have googled so many concept for building a multi-tenant app server but still don't understand how to really done it, what is the right way to do it and what is actually required to do this task. So I've come to this questions, Do I need a proxy server, dns masking, etc.. How to monitor each tenants activity What about server performance, load balancing, and scalability How to setup ssl certificate for each tenant what about application cache for each tenant Is it reliable to use the setup for production etc ... I have a very litte experience on server infrastructure, so I'm looking for a DIY walkthrough, step by step guide, or sophisticate solution ready to implemented for production

  Read the article

• Which upgrade path for disk IO bound postgres server?

  - by user41679

  Hi all, We currently have a Sun x4270 with 2xquad core Xeon Nehalmen 2.93ghz cores (16 threads), 72 gig of ram and 16 x 10k SAS disks split between the os raid 1, a partition for the Write Ahead Logs which is raid 10 and a partition for the database tables and indexes which is also raid 10, all xfs. I'm currently evaluating which path to go down in terms of upgrades. We'll be sharding the DB at some point soon, but for now I need to focus on hardware upgrades specifically. The machine is not CPU or memory bound at all at the moment, just IOWait is become an issue. The machine is mostly write access as we have a heavy caching layer. We're seeing about 300 write IOPS average on both the database partitions. We don't have any additional storage infrastructure like a Fiber Channel or ISCSI network. Budget isn't too much of a concern, something inline with the size of this server (i.e no $1m IBM machines) Space is ok on the DB side of things, we're running out obviously but there's also some reduction we can do. Additional space would be good though. My current thoughts are either: * ISCSI SAN, possible with 10Gbit network that has solid state acceleration. * FusionIO card / Sun F20 card (will the FusionIO card work in the Sun box? * DAS shelf (something like this http://www.broadberry.co.uk/das-direct-attached-storage-servers/cyberstore-224s-das) which a combination of 15k sas disks and some Intel X25-E drives for DB indexes etc) what would I need to put in the x4270 to add a DAS shelf? I think it's a SAS HBA card, do I have to use Sun's own card or will any PCI Express card work? Anything else??? what would you guys do from your experience? I appreciate it's a lot of questions, but I haven't expanded a DB machine for a number of years and the landscape has changed dramatically since then! Any advice or feedback would be very much appreciated. Let me know if there's anything else I can clarify. Thanks in advance!

  Read the article

• Migrating to Windows Server 2008 R2 Domain Controllers - a few Questions/Issues

  - by Chris

  Ok so here's our setup: We have 2 Windows 2003 Domain Controllers. I am trying to replace them with Windows 2008 R2. The 2003 servers are named DC01 and DC02. The 2008 R2 servers are DC1 and DC2. I prepared the Windows Server 2003 Forest Schema for a Domain Controller that runs Windows Server 2008 or Windows Server 2008 R2. Then with both of the new servers up as member servers I ran dcpromo on DC1 using the advanced option and added it successfully to my existing domain. It's roles are GC, DNS and Active Directory Domain Services. I transferred The PDC Emulator, RID Pool Manager, and Infrastructure Master roles to DC1. The Schema Master and Domain Naming master are still on DC01. The first issue that I'm encountering is when I dcpromo the DC2 and select "Replicate data over the network from and existing domain controller" I select that I want to replicate from DC1 and I get the following error: Failed to identify the requested replica partner (dc1.xxx.org) as a valid domain controller with a machine account for (DC2$). This is likely due to either the machine account not being replicated to this domain controller because of replication latency or the domain controller not advertising the Active Directory Domain Services. Please consider retrying the operation with \dc01.xxx.org as the replica partner. "The server is unwilling to process the request. Is this because the Schema Master and Domain Naming Master roles are still on the old DC01? And if so, if I transfer Schema Master and Domain Naming Master roles to DC1 what is the risk or breaking my AD? I'm a little paranoid because this process HAS to be transparent. ANY down time or interruption will result in me getting a verbal ass kicking from my I.T. Director. Both of the new servers DNS point the the old DNS servers (DC01 and DC02) not themselves by the way.

  Read the article

• EMC VNX iSCSI setup - unsure about SP/port assignment

  - by pauska

  We have a new VNX5300 waiting to get configured, and I need to plan out the network infrastructure before the EMC tech arrives. It has 4x1gbit iSCSI per SP (8 ports in total), and I'd like to get the most out of the performance until we jump over to 10gig iSCSI. From what I can read from the docs - the recommendation is to use only two ports per SP, with 1 active and 1 passive. Why is this? It seems kind of pointless to have quad-port i/o-modules and then recommend to not use more than two of them? Also - I'm a bit unsure about the zoning. The best practices guide state that you should separate each port on each SP from each other on different logical networks. Does this mean that I have to create 4 logical networks to be able to use all 8 ports? It also gives the following example: Does this mean that A0 and B0 should sit on the same physical switch aswell? Won't this make all traffic go on one switch (if both A1 and B1 are passive)? Edit: Another brainpuzzle I don't get it - each host (as in server) should not have more iSCSI bandwidth available than the storage processor. What on earth does this matter? If serverA have 1gbit and serverB have 100mbit, then the resulting bandwith between them is 100mbit. How can this result in some kind of oversubscription? Edit4: Wait, what. Active and passive ports? The VNX runs in a ALUA configuration with asymmetrical active/active.. there shouldn't be any passive ports, only preferred ones..

  Read the article

• Can't ping guest OS from Windows XP SP3 host running VIC.

  - by Vittal

  Hi, I am running VMware ESX Server 3i Version 3.5.0 and accessing this server using VMware Infrastructure Client Version 2.5.0 on a Windows XP SP3 machine. I have enabled the Microsoft TCP/IP version 6 stack and assigned an IPv6 address (using the netsh command) to the network adapter. The guest OS'es running on ESX Server (includes Win7, W2K8, WinXP) also have IPv6 addresses enabled on their adapters. The adapters are configured to be in VM Network (Bridged mode) and hence have connectivity to the Internet. The VMs are able to ping each other using IPv6 addresses and are also able to ping a physical Win7 machine using IPv6 addresses. However, the Windows XP SP3 machine on which the Client is running is not able to ping any hosts running on ESX Server while the VMs are able to ping this host. Whenever I try to ping from WXP box I get the "Invalid source route specified." error. The WinXP machine is not able to ping the Win7 physical machine too (the same error as above is thrown). Can someone help me understand why I am receiving this error and what I need to do to resolve this error? Thanks, Vittal

  Read the article

• SharePoint 2010 Enterprise wiki - [New page] missing

  - by icelava

  I am trying to ramp up knowledge on SharePoint deployment and usage (never did before), due to a direction to use SharePoint 2010 as a repository platform (wiki format) for our customer's infrastructure documentation. In my test virtual server, a new site of Enterprise wiki template was setup. Went into Site Actions Manage Site Features to activate Wiki Page Home Page. The default sub-web then went from /Pages to /SitePages and looks like the default Team template. The odd thing is the Site Actions is missing the New Page option. My colleague does not understand why this is the case, as it ought to be there. The original /Pages sub-web does have the option. What conditions are in play that influences the appearance of that option? UPDATE Another phenomenon observed is in the Site Actions View All Site Content view, the wiki document libraries listed in the grid will have their hyperlink (e.g. "Site Pages") lead straight to the direct default page. It would not show its own table listing of pages under that document library, unlike the original Pages document library, which expectedly show up as a listing. I wonder if this hints to any problems.

  Read the article

• Looking for ballpark pricing on an affordable a Cisco VOIP solution for our office

  - by guytech

  We have about 8 incoming PSTN lines that are currently on an old and antiquated Nortel Meridian ICS system. This system has been giving us some grief. We're looking for a new VOIP solution. I've been looking at a Cisco solution and it does seem pricey but I'm sure effective. Unfortunately, we probably can't afford a Cisco Unified Communications 520 which seems to be the ideal solution. We have about 15 people who need an extension and voicemail. We really don't have any need for a fancy system just an auto attendant of some sort when people call us. It looks like we'll have to get an older router and an addon card for what we're looking for to get best value pricing. However, I don't know a a lot about Cisco voice products so I'm a bit lost as to what to get. The only thing I am sure on is the pricing on VOIP phones which we expect to be about ~$100-200. However, I'm not sure what pieces of VOIP infrastructure to get. Any advice? I am familiar with Asterisk but right now I'm looking on pricing concerning a Cisco solution.

  Read the article

• Barriers to IPv6 deployment: addressing

  - by sysadmin1138

  There are several things that are keeping IPv6 deployment from being a topic of active discussion here at my work. There are the usual technical issues, but one non-technical one appears to be a major stumbling block on the path to actually getting a deployment project going. Addresses, memorizing of. Specifically, IPv4 addresses are comprehensible, and IPv6 addresses just look like a big long string of hex. The human mind has real trouble memorizing lists of more than 7-8 items, and an IPv4 address (192.168.231.148) has four items in it which makes it easy for us to memorize. A fully populated IPv6 address has not only 8 sections, but each section has 4 hex digits in it. IPv6 addresses were not designed for memorization. To the technician who knows that the DNS server is at 192.168.42.42 (or more likely "42.42", since the company prefix is likely memorized), the idea of memorizing an IPv6 address fills them with dread. Which in turn makes them much less enthusiastic about participating in an IPv6 deployment project. Because of how our network works we're not fully dynamic in terms of v4 addressing. We have several to many subnets that are entirely statically assigned for a variety of reasons, chief among them being that the overhead of static DHCP assignments is perceived as being too great. Also, some devices still aren't smart enough to pull DNS addresses out of DHCP while also having a static assignment, and therefore require manually configured DNS settings. Therefore, some v6 address memorization will have to be done. We're not under any mandate to get v6 out the door, so we don't have pressure from the top. However, it is time to start prepping our infrastructure to handle IPv6 even if we don't convert wholesale. For those of you who have been in IPv6-land for a while, what short-cut methods do you use to discuss or keep track of subnets and specific/critical IP addresses? If I can help reduce some of the dread surrounding IPv6 we might get the project going.

  Read the article

• How to setup NTFS ACL with Acces Based Enumeration

  - by Patrick Pellegrino

  We're in the process of migrating from Novell Netware to Windows 2K8 R2 infrastructure (AD, File server, print server... etc) My question is about ACL. While Netware and Windows are totally different, I want to be sure my thnking is good before screwing everything up! There's a scenario : F: | +-- DATA <= Shared as DATA with Access based enumeration | +-- Folder 1 +-- Team 1's Folder +-- Team 2's Folder ... In that case, by default, rights are herited from the F: to the deepest folders. What we want : Administrators group have full control top - down. From DATA, ABE list only folders that users have access. (ex. : I'm in group Team 2, I see Team 2's Folder). From what I understand, at DATA I remove all NTFS ACL to be herited (ex. Users Group), be sure to keep Administrators Group and SYSTEM user. After that, grant Full control (or any right needed) on each folder to Groups or Users that have to have access. Does I'm wrong ? Anything I should take care of ? Any help to my understanding will be very appreciated. Regards.

  Read the article

• XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

  - by ewall

  Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

  Read the article

• IIS 7.5 fails to open database after computer machine on that database server is working restarts.

  - by Jenea

  Hi. I decided to post this question also here in case the issues we have is related to sql server. There is a problem that bother me for some time. I have an asp.net mvc that uses NHibernate for modeling the database. The infrastructure is the following: Windows 2008 R2 for all virtual machines. IIS 7.5 is working on one virtual machine. Sql Server 2008 is working on another virtual machine. We have couple of databases, two that stores application data and one that registers all unhandled exceptions. Sometimes virtual machine that hosts database server restarts (in the middle of the night, not quite sure about the reason) after that connection to the databases that stores application data is not working and as result there are thousands of unhandled exceptions that get registered in the third database. Important to mention that databases are accessible from Management Studio. The problem is solved by resetting IIS. Connetion are handled via NHibernateUtil class which opens and closes session at each request.

  Read the article

• Does my Oracle DBA need root access?

  - by Dr I

  I'm currently discussing with my Oracle DBA Collegue that request a root access on our production servers. I'm not so hot to let him use the root access on our production servers. He is arguing that he need it to perform some operations like restarting the server and some other obscure arguments. The point is that I'm not agree with him because I've set him a Oracle user/group and a dba group where Oracle user belong. Everything is running smoothy and without any root permissions for now. I also think that all administrative tasks like scheduled server restart and so one need to be operated by the proper administrator (The Systems administrator on our case) to avoid any kind of issues related to a misunderstanding of the infrastructure interactions. So, I need the help of both, sysadmins and Oracle DBAs to lead me on the correct direction. If my collegue really need this rights I'll give him, but I'm just basically quite affraid of that because of security and integrity concerns. I know that my collegue is really good as a Oracle DBA and he know is work very well, but I also know that I've very few cases where a software and its admin really need root access. Once again, I'm not looking for pros/cons but rather an advice on the way that I should take to deal with this situation.

  Read the article

• Autounmounting USB keys with FAT filesystem on Linux (RHEL5)

  - by niXar

  For security reasons, I have two workstations i front of me, and I can only transfer data between them through a USB key. As you can imagine, it can get quickly tiresome, but the most annoying is having to unmount the things before removing them. Not umounting them results in missing files most of the time, even if I remove them a while after having last written to them. Now, since they're only used for transferring smallish files, and each are basically written once and read once, I don't need the fancy pansy caching infrastructure that makes clean unmounting a necessary step. And since the data is always a copy of something I have at hand, I don't care if the filesystem croaks from time to time. But anyway the system doesn't need to force that on me, it could simply make sure everything is committed with a second, and works synchronously. Then when I remove the key, nothing is lost. Is there a way to do this? I would appreciate any other tips on handling this situation. Edit: it appears the situation has changed between RHEL5 and Fedora up to F11 on one hand, and F12 on the other. The latter use DeviceKit-disk, and I haven't quite figured out how to do this. The method provided below in gconf does not work anymore.

  Read the article

• Does a VPN requirement kill the concept of having a Web Application in the Cloud?

  - by Christian

  Recently I posted a question in SO, but so far I got no answers. I wonder if I'm asking the wrong question. This is the problem: We need to design an application which offers a public http web service, but at the same time it must consume some services through a VPN connection from other existing company. There is no other alternative but to use a VPN connection to access those services. We want to host our application in some cloud infrastructure like Heroku or Amazon EC2. But there is no direct way to access the VPN services of the other company from there. The solution I'm thinking, but I don't like is to have a different server to expose the services from that VPN. But this will require the setup of another server which I prefer to avoid. In the case this is the solution, can I use an Amazon EC2 instance to connect to a VPN? This is what I was thinking, is it correct? I don't have experience using VPNs, tunnels or those kind of networking stuff. I will really appreciate if you can propose me an alternative solution, or just give me a comment.

  Read the article

• Method to integrate Powershell scripts with non-Windows workflow?

  - by Matt Simmons

  I love the smell of new machines in the morning. I'm automating a machine creation workflow that involves several separate systems across my infrastructure, some of which involve 15 year old perl scripts on Solaris hosts, PXE Booting Linux systems, and Powershell on Windows Server 2008. I can script each of the individual parts, and integrating the Linux and Unix automation is fairly straightforward, but I'm at a loss as to how to reliably tie together the Powershell scripts to the rest of the processes. I would prefer if the process began on a Linux host, since I imagine that it will end up as a web application living on an Apache server, but if it needs to begin on Windows, I am hesitantly okay with that. I would ideally like something along the lines of psexec for Linux to run against Windows, but the answer in that direction appears to by Cygwin, and as much as I appreciate all of the hard work that they put in, it has never felt right, if you know what I mean. It's great for a desktop and gives a lot of functionality, but I feel like Windows servers should be treated like Windows servers and not bastardized Unix machines (which, incidentally, is my argument against OSX servers, too, and they're actually Unix). Anyway, I don't want to go with Cygwin unless that's the last and only option. So I guess what I'm asking is if there is a way to execute jobs on Windows machines from Linux. Without Cygwin. I'm open to ideas and suggestions, including "Look idiot, everyone uses Cygwin, so suck it up and deal with it". Thanks in advance!

  Read the article

• How to organize deployment process in Chef-controlled environment?

  - by Alex

  I have a web Linux-based infrastructure which consists of 15 virtual machines and over 50 various services. It is fully controlled by Chef. Most of the services are developed internally. Basically the current deployment process is triggered by a shell script. A build system (a mix of Python and shell scripts) packages the services as .deb files and puts these packages into a repo. It runs apt-get update on all 15 nodes then because the standard Chef apt cookbook only runs apt-get once per day and we definitely do not want to run apt-get update unconditionally on each chef-client wake. The build system restarts chef-client daemons on all 15 nodes finally (we need this step because of pull Chef nature). The current process has a number of drawbacks we want to address. First off, it is asynchronous because the deployment script does not check chef-client logs after restart so we don't even know if the deployment was successful. It does not even wait for Chef clients to complete the cycle. Second, we definitely do not want to force chef-client restarts on all nodes because we usually deploy only a small number of packages. And third, I am not quite sure using chef-client for deployment is legitimate, probably we are just doing it wrong from the start. Please share your thoughts/experience.

  Read the article

< Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >