Search Results

Search found 14127 results on 566 pages for 'plz send me teh codez'.

Page 178/566 | < Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >

• IIS6.0 asking for credentials after MS Updates

  - by Adam M.

  We have an IIS6.0 Server running on a Windows 2003 Server. Last weekend it went though maintenance, and updated a quite a few Windows updates, it is now brought up to current updates (as of March 29th). Previous to these updates we could connect to the Web page via the hostname or via a alias (there is a DNS and a WINS alias (the alias is the same name in both) that are both pointing to the system). Now since the updates it asks for credentials to access the page, when trying to access the page via IP, or by name. If you use the alias it will go right into the page. I had added a new alias in DNS and tried to access it via this name with the same effect. So it appears that the WINS alias allows the page to show up properly. I have seen this KB but http://support.microsoft.com/kb/871179 though not sure if it really is relevant to this issue. As it does refer to the 3 strikes rules to display the 401.1 error. The IIS Application pool is running under a domain account. Teh default page is allowing Anonymous login under a local account. Any thoughts? Thanks Adam

  Read the article

• "Windows detected a hard drive" issue in Windows 7 x64

  - by Jasiu

  I upgraded to the OCZ-Agility3 120GB from a 60 OCZ Vertex2 SSD. I cloned the drive from the Vertex to the new Agility. Everything seemed to have gone well and have not had any problems. Recently in the passed month I have gotten this error: I downloaded teh OCZToolboxMP and ran the SMART utility and don't see anything wrong: SMART READ DATA ModelNumber : OCZ-AGILITY3 Serial Number : OCZ-Y1945X77438P4NU6 WWN : 5-e8-3a-97 ebea5ba76 Revision: 10 Attributes List 1: SSD Raw Read Error Rate Normalized Rate: 70 total ECC and RAISE errors 5: SSD Retired Block Count Reserve blocks remaining: 100% 9: SSD Power-On Hours Total hours power on: 968 12: SSD Power Cycle Count Count of power on/off cycles: 28 171: SSD Program Fail Count Total number of Flash program operation failures: 0 172: SSD Erase Fail Count Total number of Flash erase operation failures: 0 174: SSD Unexpected power loss count Total number of unexpected power loss: 11 177: SSD Wear Range Delta Delta between most-worn and least-worn Flash blocks: 0 181: SSD Program Fail Count Total number of Flash program operation failures: 0 182: SSD Erase Fail Count Total number of Flash erase operation failures: 0 187: SSD Reported Uncorrectable Errors Uncorrectable RAISE errors reported to the host for all data access: 4145 194: SSD Temperature Monitoring Current: 30 High: 30 Low: 30 195: SSD ECC On-the-fly Count Normalized Rate: 120 196: SSD Reallocation Event Count Total number of reallocated Flash blocks: 100 201: SSD Uncorrectable Soft Read Error Rate Normalized Rate: 120 204: SSD Soft ECC Correction Rate (RAISE) Normalized Rate: 120 230: SSD Life Curve Status Current state of drive operation based upon the Life Curve: 100 231: SSD Life Left Approximate SDD life Remaining: 100% 241: SSD Lifetime writes from host lifetime writes 893 GB 242: SSD Lifetime reads from host lifetime reads 968 GB Does anyone have any ideas of what might be wrong and or how I can go about fixing this? Please let me know if there is other information I can provide. Thanks for your help Windows 7 x64 SP1 AMD Phenom II X4 940 8GB RAM

  Read the article

• Puppet Agent fails sporadically, with either timeout or "Could not find class" error

  - by smokris

  I have puppet master running on a Xen dom0, and 3 domUs syncing to it via an hourly crontab puppet agent --test. About 80% of the time, the puppet agent --test completes successfully: info: Retrieving plugin info: Caching catalog for test3 info: Applying configuration version '1333319732' notice: Finished catalog run in 5.08 seconds The other 20% of the time, it fails midway, with errors such as the following: err: Could not retrieve catalog from remote server: Error 400 on SERVER: Could not find class iptables for test1 at /etc/puppet/manifests/site.pp:1 on node test1 warning: Not using cache on failed catalog err: Could not retrieve catalog; skipping run or info: Retrieving plugin info: Caching catalog for test2 info: Applying configuration version '1333319732' notice: Finished catalog run in 24.73 seconds err: Could not send report: Error 500 on SERVER: Internal Server Error private method `gsub' called for WEBrick::HTTPStatus::RequestTimeout:Class WEBrick/1.3.1 (Ruby/1.8.5/2006-08-25) OpenSSL/0.9.8e-rhel5 at puppet:8140 or info: Retrieving plugin err: Could not retrieve catalog from remote server: execution expired warning: Not using cache on failed catalog err: Could not retrieve catalog; skipping run or info: Retrieving plugin info: Caching catalog for test3 info: Applying configuration version '1333319732' notice: Finished catalog run in 9.47 seconds err: Could not send report: Error 408 on SERVER: Request Timeout During this time, I've not made any changes to the Puppet configuration — it just sporadically fails. I'm running puppet-2.7.12 on CentOS, and followed the setup instructions described on http://docs.puppetlabs.com/learning/agent_master_basic.html. Any ideas about how I can troubleshoot this?

  Read the article

• Monitor Exchange Email Address and run scripts

  - by WernerCD

  Okay... Not sure how "out there" this thought is... Right now to send a pager message (aka text message), a user logs into our AS400... logs into the program... enters user name and message and hit's F10 to send. With a little looking, it seems that you can run remote commands to the AS400 via FTP. So I'm working on building a script (batch or otherwise) that, given two parameters (user, message), will FTP into the AS400 and run a remote command: c:\>ftp server user: admin password: ***** ftp> quote rcmd SNDPGRMSG TOPGR(JDOE) MSG('This is a Test') ftp> quit So... what I want to do is setup an email account on our Exchange server Monitor the account for incoming mail upon receipt of incoming mail, parse it... say for example subject is defined as "Recipient" and email text is defined as "Pager message" run a batch that uses the above mentioned TOPGR and MSG as parameters... via FTP to the AS400 mark email as "read" The main thing I'm not sure about is monitoring an exchange account and running a script on incoming emails. I'm sure what I want to do is possible... but where would I start? EDIT: Clarification The main reasons for using this four part system are logging (messages sent via this are logged and reported by the AS400 program) and the existing scheduler for redirecting pages (For example, the weekly on-call person = TOPGR(oncall) gets updated by the AS400 program). I'm also trying to remove duplicate work. If I can get this setup working, I can redirect pages from OTHER systems into this one. I then don't have to update 2, soon to be 3, systems with current phone numbers, carriers, on-call schedules, etc. System #2 and #3 can just "email" [email protected].

  Read the article

• What DBus signal is sent on system suspend?

  - by Paul Robinson

  Hello, I need to detect when a machine is going to sleep in Ubuntu 9.10 and Fedora 13. Both use UPower, so I've been looking on the "org.freedesktop.UPower" DBus bus for such signals. I've been listening for the "sleeping" signal on the UPower bus with the following command: dbus-monitor --system "type='signal',interface='org.freedesktop.UPower',member='Sleeping'" When I sleep the machine (either by closing the lid, selecting "shutdown - suspend" or sending a DBus message) I don't see a "sleeping" event. I notice that the "Sleeping" event is sent when the "org.freedesktop.UPower.AboutToSleep" method is invoked. I can do this manually by calling: dbus-send --print-reply --system --dest=org.freedesktop.UPower /org/freedesktop/UPower org.freedesktop.UPower.AboutToSleep And I notice the "sleeping" signal is fired. My understanding is that anything that sleeps the PC must send the "AboutToSleep" signal before hand. It doesn't seem like this is happening. I've tried these steps on both Fedora 13 and Ubuntu 9.10 and I see the same results. Can anyone explain what's happening or provide me with an alternative DBus signal to listen for? Many thanks, Paul

  Read the article

• Outlook users connected to exchange can email from other email accounts

  - by Sherriffwoody

  We have found an issue on our systems whereby an outlook user (both 2007 and 2010) connected to our Exchange server (2007) can send emails as other users using the following steps Within Outlook Click <New Email> Select the <From> button to show a list of accounts outlook contains, but it also shows the option Select<Other Email Address>. This brings up a small dialog box with another button which when selected allows the user to select an email from their contacts or the Active Directory. The user in most cases can select any email within the Active Directory and send an email as if it were coming from that selected email. It seems not everyone has this ability and I'm guessing it is something to do with settings in exchange or AD(version 6) or is there a group policy that can be implemented to stop users being able to do this. We have no idea what allows this and I have failed to find anything using Dr Google. No one has setup delegates within outlook but it does seem to be something similar? Does anyone know how to lock this down? Thanks in advance

  Read the article

• email output of powershell script

  - by Gordon Carlisle

  I found this wonderful script that outputs the status of the current DFS backlog to the powershell console. This works great, but I need the script to email me so I can schedule it to run nightly. I have tried using the Send-MailMessage command, but can't get it to work. Mainly because my powershell skills are very weak. I believe most of the issue revolve around the script using the Write-Host command. While the coloring is nice I would much rather have it email me the results. I also need the solution to be able to specify a mail server since the dfs servers don't have email capability. Any help or tips are welcome and appreciated. Here is the code. $RGroups = Get-WmiObject -Namespace "root\MicrosoftDFS" -Query "SELECT * FROM DfsrReplicationGroupConfig" $ComputerName=$env:ComputerName $Succ=0 $Warn=0 $Err=0 foreach ($Group in $RGroups) { $RGFoldersWMIQ = "SELECT * FROM DfsrReplicatedFolderConfig WHERE ReplicationGroupGUID='" + $Group.ReplicationGroupGUID + "'" $RGFolders = Get-WmiObject -Namespace "root\MicrosoftDFS" -Query $RGFoldersWMIQ $RGConnectionsWMIQ = "SELECT * FROM DfsrConnectionConfig WHERE ReplicationGroupGUID='"+ $Group.ReplicationGroupGUID + "'" $RGConnections = Get-WmiObject -Namespace "root\MicrosoftDFS" -Query $RGConnectionsWMIQ foreach ($Connection in $RGConnections) { $ConnectionName = $Connection.PartnerName.Trim() if ($Connection.Enabled -eq $True) { if (((New-Object System.Net.NetworkInformation.ping).send("$ConnectionName")).Status -eq "Success") { foreach ($Folder in $RGFolders) { $RGName = $Group.ReplicationGroupName $RFName = $Folder.ReplicatedFolderName if ($Connection.Inbound -eq $True) { $SendingMember = $ConnectionName $ReceivingMember = $ComputerName $Direction="inbound" } else { $SendingMember = $ComputerName $ReceivingMember = $ConnectionName $Direction="outbound" } $BLCommand = "dfsrdiag Backlog /RGName:'" + $RGName + "' /RFName:'" + $RFName + "' /SendingMember:" + $SendingMember + " /ReceivingMember:" + $ReceivingMember $Backlog = Invoke-Expression -Command $BLCommand $BackLogFilecount = 0 foreach ($item in $Backlog) { if ($item -ilike "*Backlog File count*") { $BacklogFileCount = [int]$Item.Split(":")[1].Trim() } } if ($BacklogFileCount -eq 0) { $Color="white" $Succ=$Succ+1 } elseif ($BacklogFilecount -lt 10) { $Color="yellow" $Warn=$Warn+1 } else { $Color="red" $Err=$Err+1 } Write-Host "$BacklogFileCount files in backlog $SendingMember->$ReceivingMember for $RGName" -fore $Color } # Closing iterate through all folders } # Closing If replies to ping } # Closing If Connection enabled } # Closing iteration through all connections } # Closing iteration through all groups Write-Host "$Succ successful, $Warn warnings and $Err errors from $($Succ+$Warn+$Err) replications." Thanks, Gordon

  Read the article

• What is the advantage of not running as root? [closed]

  - by Shmuel Brill

  Possible Duplicate: What's wrong with always being root? All modern brands of Linux highly discourage (or disable) one from running as root instead of a normal user. I do not understand why. As a "normal" user, one could Download a rouge program from the internet. Run it (After all, one isn't root, what can it do). It installs itself in .bashrc or .xinitrc It writes a rouge "sudo" and "su" and adds . to the path Not noticing that . is in path, one runs sudo. The rouge program now has root password and can do anything it wants in the system. Even if 3-6 doesn't happen, the program could still Be part of a botnet. Read all files in the home directory and send them back (mine for SS#, Credit Card numbers, bank account numbers, etc). Send spam. Run a backdoor server to allow an attacker a chance to connect to the machine to determine vulnerabilities. It seems that the whole "permissions" thing (root/non-root) is just to prevent amateur crackers from getting into the system, so the question is: Is there a point in avoiding running as root, and is there a way to protect oneself if one wants to run unsafe code?

  Read the article

• VPN Device behind router/firewall

  - by David Steven

  ROUTER A: Peplink 310 serving as the gateway/router/firewall at one location. ROUTER B: Linksys RV082 serving as the gateway/router/firewall at another location. I want to VPN these two locations together. The Peplink has a PPTP server and has proprietary site-to-site vpn if you had another peplink device. The Linksys has an IPsec vpn server. VPN A: I also have another spare linksys rv082. I'm trying to setup the other rv082 (VPN A) behind the peplink (ROUTER A) and get VPN A to talk to ROUTER B. I setup VPN A with a lan ip address and plugged one of it's LAN ports into the LAN. I was able to get to it's web interface fine. On ROUTER A I one-to-one nat mapped one of our public ip's to the LAN IP for VPN A. I opened TCP 50-51 and UDP 500 to VPN A. I configured the VPN settings on VPN A to connect to ROUTER B. I did the opposite for ROUTER B. But the vpn doesn't connect. Then I tried pluging VPN A's wan port into the lan, and gave it another LAN IP. I thought perpahs VPN A didn't want to send VPN traffic out over the LAN and wanted do send it over it's WAN. The vpn still doesn't connect. It what I'm trying to do even possible?

  Read the article

• Sending Adobe PDF attachments from Adobe Reader (in Outlook 2003) takes too long

  - by White Island

  I have a customer who is using Outlook 2003 (Microsoft Online Services) and Adobe reader 9+. When they send a PDF from Adobe reader to Outlook (via the Send as attachment to e-mail feature in Adobe), it freezes for 30 seconds to 5 minutes before the new e-mail pops up with the PDF attachment. I'm pretty sure the issue is on the Outlook side of things, as I've tried Adobe reader 8 and Foxit Reader with the same results (Windows XP/7 doesn't seem to make a difference, either). I tried Outlook in safe mode on the first (Win7) machine I was working on, and the e-mail attachment worked a lot faster, but when I tried to replicate the results on another machine, one wouldn't go into safe mode, the other didn't seem to show a difference. In an effort to fix the problem in Outlook normal mode, I tried disabling all add-ins, Com add-in (Office Communicator is the only one), reading pane, Word 2003 as e-mail editor... but none of these seemed to address the issue. Does anyone have any other ideas? I need to get this resolved as soon as possible, and it doesn't seem practical to make them run in safe mode. :P

  Read the article

• How can I automatically restart Apache and Varnish if can't fetch a file?

  - by Tyler

  I need to restart Apache and Varnish and email some logs when the script can't fetch robots.txt but I am getting an error ./healthcheck: 43 [[: not found My server is Ubuntu 12.04 64-bit #!/bin/sh # Check if can fetch robots.txt if not then restart Apache and Varnish # Send last few lines of logs with date via email PATH=/bin:/usr/bin THEDIR=/tmp/web-server-health [email protected] mkdir -p $THEDIR if ( wget --timeout=30 -q -P $THEDIR http://website.com/robots.txt ) then # we are up touch ~/.apache-was-up else # down! but if it was down already, don't keep spamming if [[ -f ~/.apache-was-up ]] then # write a nice e-mail echo -n "Web server down at " > $THEDIR/mail date >> $THEDIR/mail echo >> $THEDIR/mail echo "Apache Log:" >> $THEDIR/mail tail -n 30 /var/log/apache2/error.log >> $THEDIR/mail echo >> $THEDIR/mail echo "AUTH Log:" >> $THEDIR/mail tail -n 30 /var/log/auth.log >> $THEDIR/mail echo >> $THEDIR/mail # kick apache echo "Now kicking apache..." >> $THEDIR/mail /etc/init.d/varnish stop >> $THEDIR/mail 2>&1 killall -9 varnishd >> $THEDIR/mail 2>&1 /etc/init.d/varnish start >> $THEDIR/mail 2>&1 /etc/init.d/apache2 stop >> $THEDIR/mail 2>&1 killall -9 apache2 >> $THEDIR/mail 2>&1 /etc/init.d/apache2 start >> $THEDIR/mail 2>&1 # prepare the mail echo >> $THEDIR/mail echo "Good luck troubleshooting!" >> $THEDIR/mail # send the mail sendemail -o message-content-type=html -f [email protected] -t $EMAIL -u ALARM -m < $THEDIR/mail rm ~/.apache-was-up fi fi rm -rf $THEDIR

  Read the article

• Amazon AWS Ec2 instance, Elastic IP, Domain name from external domainseller, and Google Apps for Email

  - by Sid

  We are hosting our site on an Ec2 instance. Our Elastic IP is w.x.y.z and Public DNS is: ec2-w-x-y-z.compute-1.amazonaws.com. We've bought a domain name domainname.com from a lesser known domain-name-seller. We added an A-record pointing domainname.com to w.x.y.z. Will this work or do we need a CNAME record to point to the same too? We wanted to use Google apps for emailing so adjusted the TXT/MX records according to the Google Apps instructions to be able to send/recv email using @domainname.com email addresses. Have we got it right, more important, we came across queries relating to email sent from ec2-w-x-y-z.compute-1.amazonaws.com (our users can send email from their onsite accounts) going to spam (rDNS not pointing to domainname.com but to ec2-w-x-y-z.compute-1.amazonaws.com). How can we fix this? We came across SPF records, do they provide a complete solution? We aren't sure as to how to use them. Can you help pls? Thank you, Sid

  Read the article

• Trouble with local id / remote id configuration of VPN

  - by Lynn Owens

  I have a NetGear UTM firewall and a Windows machine running NetGear's VPN client. The Windows machine I can put on the UTM network and take off of it. When I am cabled into the local (internal) the following configuration works: UTM: Local Id: Local Wan IP: (The UTM's WAN IP address) Remote Id: User FQDN: utm_remote1.com Client: Local Id: DNS: utm_remote1.com Remote Id: (The UTM's WAN IP address) Gateway authentication: preshared key Policy remote endpoint: FQDN: utm_remote1.com But when I'm off the UTM's internal local network and simply coming in from the internet, this does not work. It simply repeats SEND phase 1 before giving up. Since I know that the UTM WAN IP is accessible from both inside and outside the network, I figured the problem was with the Client local id. So, I tried the following: UTM: Local Id: Local Wan IP: (The UTM's WAN IP address) Remote Id: (A DN of a self-signed certificate I created for the client and uploaded into the UTM certificates) Client: Local Id: (The DN of the aforementioned self signed cert) Remote Id: (The UTM's WAN IP address) Gateway authentication: (the aforementioned self signed cert) Policy remote end point: ... er, ... my choices are IP and FQDN.... Not sure what to put here No matter what I've tried, it just keeps repeating the SEND phase 1. Any ideas?

  Read the article

• How to create an MST for silent install using Orca?

  - by Sanarothe

  Hi. I'm trying to deploy 7zip via GPO; I assigned the original MSI, but the package installation simply doesn't take place. What I've gathered is that I need to create an MST. In the spirit of trying to learn as much as possible about it, I've opted to use Orca rather than a third-party automagic tool, but I'm at a loss as to which fields to edit. So far the only change that I've made is to give the license accepted checkbox a value of "1" instead of pointing to another key that, still, just gave it a value of "1." So, to give this some structure, How does (Or what criteria should I consider) creating a MST make the install noninteractive/silent? Do you have to manually reconfigure the MSI to simply not perform the GUI aspects? Or do I have to execute the program in silent mode after defining the variables the the installer requests? (Though, of course, it seems that would defeat the purpose of the MST) How do I determine which fields I need to edit? I've loaded the installer and it takes three inputs: License acceptance, feature set and installation location. I want all of the default values: I'm just trying to deploy it at all, not customize the installation. I BELIEVE that I should be messing with some values in the Registry table, but I really don't know. If I'm not asking the right questions, can someone point me to a THOROUGH resource or documentation for this process? I've already gone over the technet articles on basic Orca use and deployment, but I couldn't really find anything on creating MST that didn't involve a third party program in which one runs a 'dummy' installer to get the before and after snapshots. Thank you very much, Cameron UPDATE: After spending the day troubleshooting, I finally got my server to send out 7zip, but not until I had also assigned firefox. Not sure why it didn't want to send out 7zip by itself, but I also had some domain naming problems. Thanks for the input (GPResult helped enormously.)

  Read the article

• Rebooting access point via SSH with pexpect... hangs. Any ideas?

  - by MiniQuark

  When I want to reboot my D-Link DWL-3200-AP access point from my bash shell, I connect to the AP using ssh and I just type reboot in the CLI interface. After about 30 seconds, the AP is rebooted: # ssh [email protected] [email protected]'s password: ******** Welcome to Wireless SSH Console!! ['help' or '?' to see commands] Wireless Driver Rev 4.0.0.167 D-Link Access Point wlan1 -> reboot Sound's great? Well unfortunately the ssh client process never exits, for some reason (maybe the AP kills the ssh server a bit too fast, I don't know). My ssh client process is completely blocked (even if I wait for several minutes, nothing happens). I always have to wait for the AP to reboot, then open another shell, find the ssh client process ID (using ps aux | grep ssh) then kill the ssh process using kill <pid>. That's quite annoying. So I decided to write a python script to reboot the AP. The script connects to the AP's CLI interface via ssh, using python-pexpect, and it tries to launch the "reboot" command. Here's what the script looks like: #!/usr/bin/python # usage: python reboot_ap.py {host} {user} {password} import pexpect import sys import time command = "ssh %(user)s@%(host)s"%{"user":sys.argv[2], "host":sys.argv[1]} session = pexpect.spawn(command, timeout=30) # start ssh process response = session.expect(r"password:") # wait for password prompt session.sendline(sys.argv[3]) # send password session.expect(" -> ") # wait for D-Link CLI prompt session.sendline("reboot") # send the reboot command time.sleep(60) # make sure the reboot has time to actually take place session.close(force=True) # kill the ssh process The script connects properly to the AP (I tried running some other commands than reboot, they work fine), it sends the reboot command, waits for one minute, then kills the ssh process. The problem is: this time, the AP never reboots! I have no idea why. Any solution, anyone?

  Read the article

• external postfix forwarding to zimbra server

  - by Marko

  I want to migrate from my current mail server (old_server) for my domain mydomain.com. old_server setup is Postfix+LDAP+Cyrus. Now I want to migrate my domain mail to Zimbra server (zimbra), but I am considering option to leave current mail server working in the first phase, and then to only have subset of email addresses to be forwarded to zimbra server. It seems that zimbra refers this in their documentation as 'edge MTA'. Current config mydomain.com MX: old_server <---------- smtp send ----------> smtp receive New config mydomain.com MX: old_server zimbra <------------------------------------------- smtp send ----------> smtp receive ---- forward ----> smtp receive I need following: old_server to receive mail for my domain as before, but for some of the email addresses I want them to be delivered to zimbra server. I should be able to determine which email addresses will be forwarded. I would like to avoid possible false spam detections for mails from mydomain.com due to this setup. Questions: How should I configure postfix on old_server to support this mail forwarding? To avoid false spam detection, can I have outgoing mail from mydomain.com to be sent by zimbra or should I use old_server? Is there anything extra I would need to do in order to avoid possibility of my outgoing mails being marked as spam on other servers?

  Read the article

• Linux/Unix MTA with the smartest queue?

  - by threecheeseopera

  I am looking for an MTA that will allow me (a script, really) to proactively manage it's send queue in response to status codes returned by the remote servers I am delivering to. Basically, for each mail sent I would like to be able to react to the SMTP reply code returned by the remote server, ex. '250 OK', or to any error conditions like connection timeouts. Additionally, I would like to be able to manage the send queue moving forward based on this information, e.g. 'example.com has timed out the last 5 connection attempts, so no longer queue mail for recipients @example.com'. I am currently using postfix and perl to parse it's logs for this information, but I am playing a game of catchup that is prone to errors (out-of-order log entries etc.) and it's starting to get messy (some real ugly regexes ;). I really don't want to reinvent the wheel and use some language's smtp library; i would prefer to use a proven/fast/reliable MTA. I am however open to suggestions if what I need just isn't possible. Thanks for your help!

  Read the article

• Sendmail in Nexenta core 3.0.1

  - by maximdim

  I'm trying to setup sendmail in Nexenta core 3.0.1 (Solaris based OS). All I want is to be able to send emails from that host - like notifications about failures, cron jobs output etc. Initially Nexenta core doesn't have sendmail so here is what I've done: apt-get install sunwsndmu Now there is a sendmail in /usr/sbin/sendmail. When I try to send email from command line: $mail maxim test . It doesn't give me any error but in log file I see: Dec 20 12:41:08 nas sendmail[12295]: [ID 801593 mail.info] oBKHf8u7012295: from=maxim, size=107, class=0, nrcpts=1, msgid=<201012201741.oBKHf8u7012295@nas>, relay=maxim@localhost Dec 20 12:41:08 nas sendmail[12295]: [ID 801593 mail.info] oBKHf8u7012295: to=maxim, ctladdr=maxim (1000/10), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30107, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection refused by [127.0.0.1] So I guess I need to have SMTP service running. How do I do that in Nexenta? svcs -a | grep sendmail doesn't return anything and # svcadm enable sendmail svcadm: Pattern 'sendmail' doesn't match any instances I'm not married to sendmail so if there are easier ways to achieve y goal I'm open to suggestions as well. Thanks,

  Read the article

• Use to host email for a domain name that wasn't our primary domain name

  - by drpcken

  Exchange 2007 on an Server 2003 active directory. My primary domain (MyMainDomain.com) controller also hosts dns and dhcp. I have a secondary domain name (MySecondDomain.net) that my Exchange Server allows emails from. It wasn't a physical domain, just accepted by exchange and setup as the Active Directory user's main smtp and outgoing address. Its MX records point to MyMainDomain.com's public exchange address. I've taken MySecondDomain.net and move the mail boxes to a hosted exchange 2010 environment. MX records now point to this new exchange system and when I send and email OUTSIDE the MyMainDomain.com environment (say gmail) it works and sends to the hosted exchange setup for MySecondDomain.net. however when I send an email from a user on MyMainDomain.com, it goes to the old exchange 2007 server I am hosting internally. I have removed MySecondDomain.net from the allowed domains, removed the DNS zone for MySecondDomain.net, and cleared DNS cache. I was convinced it was my internal dns server but I've cleared the DNS cache. Is there something I'm missing somewhere in exchange 2007? Or is it my domain controller/dns? Sorry if this is confusing. Thank you!

  Read the article

• Exchange eMails In A Mailbox Appear To Be Blocked By A Dud Message

  - by John Judd

  I have a client with an Exchange server on which there are quite a few mailboxes. One mailbox in particular is causing some problems. When an email from a certain address arrives, it appears to prevent Exchange from successfully delivering the email to the Outlook Express inbox. The address in question is from an account with Bigpond, or at least I think it is, I didn't check to see if it was spoofed (only just occurred to me.) Any emails in the queue before the suspect email are delivered, then Express times out. When send/recv is retried those emails are re-received and the process times out again. The process I have for fixing this is to log in to the sever, load Outlook, open the recipients inbox, and delete the suspect email. Then retrying the send/recv on Express successfully retrieves all the messages (except for the deleted message.) This solves the immediate problem, but this has happened several times now, and each time requires the process above to correct it. What I am wondering is if there is anything I can do to fix this permanently. It seems to me that Exchange should reject a dud email message rather than getting stuck. Does anyone know what could be causing this, and how I can fix it?

  Read the article

• Port translation in router causing some email to fail

  - by user22037

  We are in the process of setting up a spam filter (SAVASM). One change we are making is to push incoming email on port 25 through our spam filter/server but have users actually send their email on a different port. I am attempting to make this happen by using port address translation to send port 25 traffic to the SAVASM server IP. As a step in making this change I setup port translation without actually changing the IP addresses. The NAT rules for the email server went from one Static NAT rule with no port specified, to multiple Static NAT rules each with a port or group matching the Access Rules for that server (smtp, pop3, http, https, and some other custom ports). The problem we are running into is confusing. Some outgoing mail through this server is failing when the router has the multiple NAT rules with port translation settings. Email goes through fine FROM our email to our internal accounts and to Gmail. However email fails when FROM our client's email address TO our client's email or their personal Comcast. The only situation that worked for them was if they changed FROM to Comcast and then messages went through fine to both Comcast and the client's accounts. Switching back to regular Static NAT rule everything then worked for them. Does anyone have a clue as to what might be going on? We are on a Cisco ASA 5500 box.

  Read the article

• Can't pop3 from exchange server after a reboot

  - by BLAKE

  Last night I shutdown my Exchange 2003 Virtual Machine, I added a new VHD (For backups), and booted it again. Now I can't POP3 email from it with Outlook 2007. In Outlook I get the error: Task '[email protected] - Receiving' reported error (0x800CCC0F) : 'The connection to the server was interrupted. If this problem continues, contact your server administrator or Internet service provider (ISP).' Does anybody know what is wrong? All I did was a reboot. I haven't formated the added disk. There are no weird errors in the event log. I can still send mail with Outlook over port 25. I can send and recieve mail with OWA. I can POP3 the mail to my phone (it take about 15 minutes after sending a message, but I do get it eventually). EDIT: The 'Microsoft Exchange POP3' Service says that it is started but if I stop it and try to start it again, it fails saying 'Could not start the Microsoft Exchange POP3 service on Local Computer. Error 1053: The service did not respond to the start or control request in a timely fashion.' I did some googling and someone on exchangefreaks.com said that if I use task manager to 'End Task' on inetinfo.exe, then I can start the POP3 service fine. Does anyone know what causes this problem? I am fine for now since I did get the Service started, but If it does this after every reboot...

  Read the article

• NOQUEUE: SYSERR(root): opendaemonsocket: daemon MTA-v4: cannot bind: Address already in use

  - by Francesco

  I have an issue with sendmail on my server (ubuntu 12.10) with php, mysql,and wordpress installed. Basically I want to create a contact form in my blog to receive emails from visitors directly into my gmail account but it doest work! I created a php file called testmail.php to recall it from the browser: <?php $to = '[email protected]'; $subbject = 'TEST MAIL'; $msg = 'test test test test test test test test test test test test test test test'; $isMailed = mail($to, $subbject, $msg, 'From:me <[email protected]>'); if($isMailed) echo 'mail has been send to: ' . $to; else echo 'mail has NOT been send..'; ?> But I dont receive anything! The /var/log/mail.log says: NOQUEUE: SYSERR(root): opendaemonsocket: daemon MTA-v4: cannot bind: Address already in use What do i do wrong? Where do I need to check? What info do you need more? I checked also into the spam folder, nothing. Thank you!

  Read the article

• iRedMail home setup - use different SMTP relay for different destination domains

  - by John

  Hello helpful server folks, I'm messing with iRedMail. I've mostly been successful, I think I have an SMTP problem. I have changed RoundCube (webmail) to use BrightHouse's, my ISP's, SMTP server for outgoing. It works fine, I click send and poof, I have gmail. I can reply from gmail to my email server, and it works. It took 10 hours for the email to show up, which is a different problem, I think, but it does work. But when I send from my server TO my own server, my ISP's Postmaster account sends me a cryptic blurb. I just got off the phone with them, and they say it "should work", and that they can't reach my pop3 server. (pop3, pop3s, imap, and imaps are all open on my router and forwarded to the server, I'm not sure what I need, I'm just covering my bases...) pop3 and/or imap as external interfaces are just formalities, I really just want webmail to work. Roundcube only takes one SMTP server in its configs. How can I configure Postfix to relay / forward emails to my ISP's SMTP, while taking messages bound for my own domain and processing them? Since my ISP won't let me "bounce" my emails off of it. Maybe I'm vastly misunderstanding how e-mail works in general: To receive mail, I should only need port 25, SMTP, open to the internet, correct? Should I be concerned about some authentication failure from the outside to my relay? (My relay requires user/pass to use, my ISP's requires none.)

  Read the article

• How to handle server failure in an n-tier architecture?

  - by andy

  Imagine I have an n-tier architecture in an auto-scaled cloud environment with say: a load balancer in a failover pair reverse proxy tier web app tier db tier Each tier needs to connect to the instances in the tier below. What are the standard ways of connecting tiers to make them resilient to failure of nodes in each tier? i.e. how does each tier get the IP addresses of each node in the tier below? For example if all reverse proxies should route traffic to all web app nodes, how could they be set up so that they don't send traffic to dead web app nodes, and so that when new web app nodes are brought online they can send traffic to it? I could run an agent that would update all the configs to all the nodes, but it seems inefficient. I could put an LB pair between each tier, so the tier above only needs to connect to the load balancers, but how do I handle the problem of the LBs dying? This just seems to shunt the problem of tier A needing to know the IPs of all nodes in tier B, to all nodes in tier A needing to know the IPs of all LBs between tiers A and B. For some applications, they can implement retry logic if they contact a node in the tier below that doesn't respond, but is there any way that some middleware could direct traffic to only live nodes in the following tier? If I was hosting on AWS I could use an ELB between tiers, but I want to know how I could achieve the same functionality myself. I've read (briefly) about heartbeat and keepalived - are these relevant here? What are the virtual IPs they talk about and how are they managed? Are there still single points of failure using them?

  Read the article

< Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >