Search Results

Search found 9456 results on 379 pages for 'controller'.

Page 18/379 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

• iSCSI timeouts under high load

  - by Antonio

  I have two servers connected via Gigabit Ethernet. One is iSCSI target, the second one is initiator. When I run mkfs.ext4 at initiator, after a while disk IO slows down critically. In the target host I can see the following in syslog: Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119668c 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119668c 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119668d 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119668d 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119668e 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119668e 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 1196696 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 1196696 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119669e 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119669e 6 Sep 14 09:40:04 sh11 tgtd: abort_task_set(1139) found 119669f 0 Sep 14 09:40:04 sh11 tgtd: abort_cmd(1115) found 119669f 6 And load average grows to 12 or even more: # uptime 12:37:00 up 23 days, 13:25, 1 user, load average: 12.00, 7.00, 4.00 CentOS 6.3 tgtd 1.0.24 Intel Pentium 4 2.4GHz 1Gb RAM 2Tb WD Cavlar Green SATA 2.0 #lspci 00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 02) 00:01.0 PCI bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE Host-to-AGP Bridge (rev 02) 00:1d.0 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 82) 00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 02) 00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 02) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV200 QW [Radeon 7500] 02:01.0 Ethernet controller: D-Link System Inc DGE-530T Gigabit Ethernet Adapter (rev 11) (rev 11) 02:02.0 RAID bus controller: VIA Technologies, Inc. VT6421 IDE/SATA Controller (rev 50) 02:03.0 RAID bus controller: VIA Technologies, Inc. VT6421 IDE/SATA Controller (rev 50) 02:04.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 02:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (CNR) Ethernet Controller (rev 82) Is there a way to tune target host to avoid these timeouts?

  Read the article

• Architecting ASP.net MVC App to use repositories and services

  - by zaladane

  Hello, I recently started reading about ASP.net MVC and after getting excited about the concept, i started to migrate all my webform project to MVC but i am having a hard time keeping my controller skinny even after following all the good advices out there (or maybe i just don't get it ... ). The website i deal with has Articles, Videos, Quotes ... and each of these entities have categories, comments, images that can be associated with it. I am using Linq to sql for database operations and for each of these Entities, i have a Repository, and for each repository, i create a service to be used in the controller. so i have - ArticleRepository ArticleCategoryRepository ArticleCommentRepository and the corresponding service ArticleService ArticleCategoryService ... you see the picture. The problem i have is that i have one controller for article,category and comment because i thought that having ArticleController handle all of that might make sense, but now i have to pass all of the services needed to the Controller constructor. So i would like to know what it is that i am doing wrong. Are my services not designed properly? should i create Bigger service to encapsulate smaller services and use them in my controller? or should i have an articleCategory Controller and an articleComment Controller? A page viewed by the user is made of all of that, thee article to be viewed,the comments associated with it, a listing of the categories to witch it applies ... how can i efficiently break down the controller to keep it "skinny" and solve my headache? Thank you! I hope my question is not too long to be read ...

  Read the article

• View controller is drawing under my navigation bar after popping ttthumbsviewcontroller

  - by scootklein

  I'm implementing the TTThumbsViewController from the Three20 project and things are finally starting to take shape. I push the TTThumbsViewController from the current view controller by just pushing it onto the current stack and animate the transition (common navigation controller push). My problem is that when I pop the TThumbsViewController view controller, the navigation controller is stuck in a mode where its view controllers are drawn UNDER the navigation bar (which is now translucent). Start Push Pop

  Read the article

• RAID Volume is no longer showing in Raid Controller BIOS and in Windows

  - by Gordon

  Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. For their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

  Read the article

• Lenovo S110 netbook screen resolution Ubuntu

  - by Neigyl R. Noval

  I am still stuck with 800x600 resolution. Here is the output of lspci: 00:00.0 Host bridge: Intel Corporation Device 0bf2 (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Device 0be2 (rev 09) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8176 (rev 01) Also, I tried modifying /usr/lib/X11/xorg.conf.d/10-monitor.conf to fix this problem, but still does not work: Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Screen" Identifier "Screen0" Monitor "Monitor0" Device "Card0" SubSection "Display" Viewport 0 0 Depth 1 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 4 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 8 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 15 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 16 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" EndSubSection EndSection Section "Device" Identifier "Card0" Driver "vesa" VendorName "Intel Corporation Device" EndSection I'm using Gnome. System Preference Monitor screen resolution sticks to 800x600. What am I going to do?

  Read the article

• Debian: What are these files in /sys/devices/pci0000:00/ for?

  - by muhuk

  I am running Debian Squeeze on an MSI M670 laptop. I have these following files on my root drive, each 256MB: file:///sys/devices/pci0000:00/0000:00:05.0/resource1 file:///sys/devices/pci0000:00/0000:00:05.0/resource1_wc Here is my lspci output: muhuk@debian:~$ lspci 00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2) 00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) 00:05.0 VGA compatible controller: nVidia Corporation C51 [GeForce Go 6100] (rev a2) 00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3) 00:0a.3 Co-processor: nVidia Corporation MCP51 PMU (rev a3) 00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1) 00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 04:04.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 04:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 04:04.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 04:09.0 Network controller: RaLink RT2561/RT61 rev B 802.11g I am speculating these have something to do with the shared RAM my GPU is using. But why a file on disk? And why two of them?

  Read the article

• Extending Controller

  - by MakDotGNU

  Hi, I'm very new to Kohana and I'm trying to make a project in kohana 2.x, in my previous projects i had created a Base controller which used to extends Controller. and all other controller to Base_Controller. in Kohana I'm facing the problem. here is my structure. class Base_Controller extends Template_Controller class Home_Controller extends Base_Controller both these Controllers are in application/controller folder Fatal error: Class 'Base_Controller' not found in /home/myadav/public_html/innteract/innteract/controllers/home.php on line 2

  Read the article

• Controller inside MVC architechture

  - by Vinay

  Hi All, I want to know about the controller in struts MVC architecture. Does struts-conf.xml file is a controller. I know that it is a part of controller, but someone is saying that it is a controller and at what extend it is true. Please explain it. Thanks Vinay

  Read the article

• How to call a different post to a different controller in Rails Functional Test

  - by Snehal

  I want to make a post request to a different controller inside my functional test which is intended for a particular controller. However the post method in ActiveController class just takes the method to be called, it doesn't take the controller name to be called. Any ideas how to invoke a different controller?

  Read the article

• Facade controller, is it efficient?

  - by Berlioz

  Using a facade controller pattern in .net. It seems as if though it is not efficient BECAUSE, for every event that happens in a domain object(Sales, Register, Schedule, Car) it has to be subscribed to by the controller(use case controller) and then the controller in turn has to duplicate that same event to make it available for the presentation, so that the presentation can show it to the user. Does this make sense? Please comment!

  Read the article

• Tab Bar and Nav Controller: Where did I go wrong in my Interface Builder wiring?

  - by editor

  Even if you don't know how I've shot myself in the foot, a story which I've tried to lay out below, if you think I've done a good job showing the parameters of my problem I'd appreciate an upvote so that I might be able to grab some attention for my question. I've been working on an iPhone application in XCode and Interface Builder of the Tab Bar project type. After getting a table view of topics (business sectors) working fine I realized that I would need to add a Navigation Control to allow the user to drill into a subtopics (subsectors) table. As a green Objective-C developer, that was confusing, but I managed to get it working by reading various documentation trying out a few different IB options. My current setup is a Tab Bar Controller with Tab 1 as a Navigation Controller and Tab 2 a plain view with a Table View placed into it. The wiring works: I can log when table rows are selected and I'm ready to push a new View Controller onto the stack so that I can display the subtopics Table View. My problem: For some reason the first tab's Table View is a delegate and dataSource of the second ta. It doesn't make sense to me and I can't figure out why that's the only setup that works. Here is the wiring: Navigation Controller (Sectors) is a delegate of Tab Bar Navigation Bar is a delegate of Navigation Controller (Sectors) View Contoller (Sectors) has a view of Table View Table View (in Navigation Controller (Sectors)) is a delegate of First View Controller (Companies) Table View (in Navigation Controller (Sectors)) is a dataSource outlet of First View Controller (Companies) First View Controller (Companies) First View Contoller (Sectors) has a view of Table View Table View (in First View Controller (Companies)) is not hooked up to a dataSource outlet and is not a delegate When I click the tab buttons and look at the Inspector I see that the first tab is correctly hooked up to my MainWindow.xib and the second tab has selected a nib called SecondView.xib. It's in the File's Owner of MainWindow.xib where I inherit UITableViewDataSource and UITableViewDelegate (and also UITabBarControllerDelegate) in the .h, and in the .m where I implement the delegate methods. Why does this setup only work when the Table View in my first tab (View Controller (Sectors)) is a delegate and dataSource of the second tab? I'm confused: why wouldn't it need to be hooked up to the Navigation Controller-enabled tab in which the Table View is seen (Navigation Controller (Sectors))? The Table View seen on the second tab has neither dataSource and is not a delegate. I'm having trouble getting a pushViewController to fire (self.navigationController is not nil but the new View Controller still doesn't load) and I suspect that I need to work out this IB wiring issue before I can troubleshoot why the Nav Controller won't push a new View Controller onto the stack. if(nil == self.navigationController) { NSLog(@"self.navigationController is nil."); } else { NSLog(@"self.navigationController is not nil."); SectorList *subsectorViewController = [[SectorList alloc] initWithNibName:@"SectorList" bundle:nil]; subsectorViewController.title = @"Subsectors"; [[self navigationController] pushViewController:subsectorViewController animated:YES]; [subsectorViewController release]; }

  Read the article

• Backtrack, Wi-Fi not working

  - by hradecek

  I've installed Backtrack 5R3 KDE, and I realized that my wireless is not working, but wired is working fine. Here's the lshw output: *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 05 serial: 04:7d:7b:b7:46:f8 size: 100MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:42 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB Controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

  Read the article

• Volume is no longer showing in Raid Controller BIOS and in Windows

  - by Gordon

  Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

  Read the article

• Swapping RAID sets in and out of the same controller

  - by hazymat

  This is a really simple question, and the answer is probably encoded in various wikipedia articles, however my question is reasonably specific, and I need a bulletproof answer! I'm not sure if my question pertains to hardware RAID in general, or to the specific RAID controller I'm working on. Either way it is the Dell SAS 6/iR (this is an LSI sas1068e chipset). I simply want to: remove a set of striped (RAID 0) disks from this RAID controller in a server put in another set of disks, and create a RAID 1 array (or create a new 'virtual disk', as they call it in the SAS 6/iR manual) Do stuff with the new RAID 1 array Have the option of putting back the old set of disks (the RAID 0 striped ones) I am quite sure this is possible, but I need some form of reliable, evidence-based answer as it's for a client of mine, and I need to migrate their data safely. The question: can I actually do the above? Does the RAID configuration get stored on the disks themselves, or in the hardware controller? Is any data stored in the hardware controller? If there is any chance I cannot completely restore operation of the first set of disks I removed, then I need to know about it! The manual alludes to the answer to this question (see page 45 of this document), and talks about activating an array of disks. I just need someone to confirm I can definitely do the above. See, simple question, right? :)

  Read the article

• Optional Navigation Controller

  - by Kevin Sylvestre

  I have an application containing a variety of view controllers linked together in different ways (Welcome Browse Preview OR Browse Preview OR Settings Splash). The first view controller is presented modally using a navigation controller from a main controller, then the next set of view controllers are added using pop and push. This works correctly, but I need to be able to define my 'UINavigationBar' and 'UIToolbar' within interface builder, so they still work as expected if they are presented without using a navigation controller. Is this possible? Currently I get this if I try:

  Read the article

• Upgrading a PERC h310 to a PERC H710 mini RAID controller on a Dell R620

  - by Gregg Leventhal

  I have an ESXi 5.0 Free license host using an internal Datastore (RAID 5, 5 Disk) that was configured with a Dell PERC h310 RAID controller. The disk performance was very poor, so I upgraded to the PERC H710 Mini. The IT Tech installed the controller and powered the host back on. I had to rescan the controller and the datastore appeared. Should any settings be changed in the RAID BIOS, or should the default settings be sufficient? Is they anything to be aware of when performing this type of upgrade in order to achieve the maximum performance?

  Read the article

• Is there a expected set of button mappings games commonly use?

  - by Scott Chamberlain

  I am making a game that will support a XBox 360 controller but I would like to try and keep the default button mappings to be what is expected from a user's past history from playing other games. Is there a set of guidelines from Microsoft on what should map to what (Do you use A for fire or left trigger?), or has the gaming community picked up a common set of controls that is just not written anywhere, everyone just "knows" it (like WASD for movement). The hardest thing for me is I have walking movement, vehicle movement, and airplane movement. I plan on allowing custom configuration of each, but I don't know what to set as the defaults.

  Read the article

• Wireless not working with a RaLink RT3090

  - by Promather

  I recently bought a new HP DV6-3118SA laptop, but I am having a very discouraging problem with wireless LAN. It simply doesn't work! Could you please help me with this? Output of lspci -k: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) Subsystem: Hewlett-Packard Company Device 144a 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: i2c-i801 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: intel ips Kernel modules: intel_ips 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: radeon Kernel modules: radeon 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 02:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe Subsystem: Hewlett-Packard Company Device 1453 Kernel driver in use: rt2800pci Kernel modules: rt2860sta, rt2800pci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: r8169 Kernel modules: r8169 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a

  Read the article

• Wireless Not Working on Ubuntu 10.10

  - by Promather

  I recently bought a new HP DV6-3118SA laptop, but I am having a very discouraging problem with wireless LAN. It simply doesn't work! Could you please help me with this? EDIT: Following @Ronald and @Oli advice, I am dumping the output of lspci -k: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) Subsystem: Hewlett-Packard Company Device 144a 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: i2c-i801 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: intel ips Kernel modules: intel_ips 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: radeon Kernel modules: radeon 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 02:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe Subsystem: Hewlett-Packard Company Device 1453 Kernel driver in use: rt2800pci Kernel modules: rt2860sta, rt2800pci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: r8169 Kernel modules: r8169 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a

  Read the article

• Strange Ubuntu Random Display [Video]

  - by d4v1dv00

  I had this random display issue ever since Ubuntu 11.04 and now running Ubuntu 11.10 and this problem still persist. It is very hard for me to explain, so I uploaded a video to elaborate itself. Before I convert from Windows 7, this issue never happened. The symptom is so random that I cannot reproduce or tell precisely when will this happen again. My wild guess is, should this be related to driver? Below are my detail system information: $ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation H67 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57788 Gigabit Ethernet PCIe (rev 01) is there any other information i need to post and how do i do that?

  Read the article

• How can I get six Xbox controllers to provide input to an HTML5 game?

  - by Daniel X Moore

  I'm creating a six player HTML 5 game designed to be played locally (Red Ice). I've previous set up handling 7 Wiimotes using something along the lines of Joy2Key to map each input for each player to a separate keyboard key, but Wiimotes are pretty hard on the hands for these types of games and not very ergonomic so I thought I'd try and get Xbox controller support. I don't believe that any simple key mapping solution will work due to the nature of the directional stick. My inclination is that this will require a browser plugin and if so I'd prefer to write the plugin for Google Chrome. How do I create a Chrome browser plugin to handle multiple Xbox controllers or is there some other way? Please do not answer this question saying it can't be done, because it absolutely can. EDIT: I don't believe any keymapping/mouse simulating solution will work unless it can reliably distinguish six axis of inputs, one per player.

  Read the article

• Is there a way to disable the hardware on/off switch for the Wireless interface?

  - by avee

  I have an HP 520 and is running the latest Ubuntu 11.10. The hardware works fine with Ubuntu with one exception: The device has a hardware switch for turning the wifi on and off. Every time the wi-fi is disabled through the hardware switch, I am unable to bring it on again. The message on the networking popup would be device not ready. What I am looking for is a way to disable the hardware switch altogether so that when users accidentally press the button, the wifi would not be disabled. There is no setting to disable the switch in the BIOS. Hardware info from lspci -nn: 00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GME Express Memory Controller Hub [8086:27ac] (rev 03) 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GME Express Integrated Graphics Controller [8086:27ae] (rev 03) 00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03) 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01) 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 01) 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 01) 00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 01) 00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 01) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e1) 00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 01) 00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller [8086:27c4] (rev 01) 02:06.0 CardBus bridge [0607]: ENE Technology Inc CB1410 Cardbus Controller [1524:1410] (rev 01) 02:08.0 Ethernet controller [0200]: Intel Corporation 82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller Mobile [8086:1068] (rev 01) 10:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02) The output from lsmod | grep iwl: iwl3945 73329 0 iwl_legacy 71499 1 iwl3945 mac80211 272785 2 iwl3945,iwl_legacy cfg80211 172392 3 iwl3945,iwl_legacy,mac80211

  Read the article

• Announcement: New Tutorial - Using ADF Faces and ADF Controller with OEPE

  - by Juan Camilo Ruiz

  We are happy to announce the publication of our newest tutorial, that explores some of the latest features added in our OEPE 12c release for ADF Development. The tutorial walks you through the creation of an ADF application that uses the ADF Faces Rich Client components, in combination with the ADF Controler, ADF Model and JPA. By developing this tutorial you will work and understand various features added into OEPE 12c that are specific to ADF development such as: ADF taskflow editor Visual pageDefinition editor ADF integration with AppXRay Navigation across artifacts such as pages, pageDefinition, managed beans, etc. Property inspector for ADF Faces components. Stay tunned for more and exciting tutorials that explore this and much more OEPE features. And of course your feedback is always welcome!

  Read the article

• Returning JsonResult From ASP.NET MVC 2.0 Controller and Unit Testing

  This post will show how to return a simple Json result from an ASP.NET MVC 2.0 web project.  It will show how to test that result inside a unit test and essentially pick apart the Json, just like a JavaScript (or other client) would do.  It seems like it should be very simple (and indeed, [...]...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Returning JsonResult From ASP.NET MVC 2.0 Controller and Unit Testing

  This post will show how to return a simple Json result from an ASP.NET MVC 2.0 web project.  It will show how to test that result inside a unit test and essentially pick apart the Json, just... This site is a resource for asp.net web programming. It has examples by Peter Kellner of techniques for high performance programming...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >