Search Results

Search found 834 results on 34 pages for 'fragment'.

Page 18/34 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

• How do I get a Belkin F5D8053 wireless adapter working?

  - by disassembler

  I've tried getting my Belkin N Wireless adapter to work on Ubuntu many times with no luck at all. Each time I seem to arrive at a dead end. After some thorough searching of UbuntuForums and WifiDocs I've gathered some information and narrowed the problem down to an issue with the rtl819xU driver. Here's some info that may help: $ sudo lshw -C network *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:22:75:38:52:ac capabilities: ethernet physical wireless configuration: broadcast=yes driver=rtl819xU multicast=yes wireless=802.11b/g/n $ sudo lsmod Module Size Used by vesafb 13449 1 snd_ice1724 106559 2 snd_ice17xx_ak4xxx 13163 1 snd_ice1724 snd_ac97_codec 105614 1 snd_ice1724 ac97_bus 12642 1 snd_ac97_codec snd_ak4xxx_adda 18436 2 snd_ice1724,snd_ice17xx_ak4xxx snd_ak4114 14326 1 snd_ice1724 snd_pt2258 12986 1 snd_ice1724 snd_i2c 13831 2 snd_ice1724,snd_pt2258 snd_ak4113 14307 1 snd_ice1724 snd_pcm 80244 4 snd_ice1724,snd_ac97_codec,snd_ak4114,snd_ak4113 fglrx 2434640 121 snd_seq_midi 13132 0 snd_rawmidi 25269 2 snd_ice1724,snd_seq_midi binfmt_misc 13213 1 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event ppdev 12849 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq dcdbas 14054 0 r8192u_usb 297246 0 snd 55295 16 snd_ice1724,snd_ac97_codec,snd_ak4xxx_adda,snd_ak4114,snd_pt2258,snd_i2c,snd_ak4113,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd parport_pc 32111 1 snd_page_alloc 14073 1 snd_pcm shpchp 32345 0 lp 13349 0 parport 36746 3 ppdev,parport_pc,lp usbhid 41704 0 hid 77084 1 usbhid e100 40108 0 floppy 60032 0 $ sudo iwconfig wlan0 802.11b/g/n Mode:Managed Access Point: Not-Associated Bit Rate:1 Mb/s Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I'd like to know if 1) Is the driver is properly installed and recognized by Ubuntu? 2) What can I do to load the drivers properly and make use of the adapter? Thanks!

  Read the article

• Deferred Rendering With Diffuse,Specular, and Normal maps

  - by John

  I have been reading up on deferred rendering and I am trying to implement a renderer using the Sponza atrium model, which can be found here, as my sandbox.Note I am also using OpenGL 3.3 and GLSL. I am loading the model from a Wavefront OBJ file using Assimp. I extract all geometry information including tangents and bitangents. For all the aiMaterials,I extract the following information which essentially comes from the sponza.mtl file. Ambient/Diffuse/Specular/Emissive Reflectivity Coefficients(Ka,Kd,Ks,Ke) Shininess Diffuse Map Specular Map Normal Map I understand that I must render vertex attributes such as position ,normals,texture coordinates to textures as well as depth for the second render pass. A lot of resources mention putting colour information into a g-buffer in the initial render pass but do you not require the diffuse,specular and normal maps and therefore lights to determine the fragment colour? I know that doesnt make since sense because lighting should be done in the second render pass. In terms of normal mapping, do you essentially just pass the tangent,bitangents, and normals into g-buffers and then construct the tangent matrix and apply it to the sampled normal from the normal map. Ultimately, I would like to know how to incorporate this material information into my deferred renderer.

  Read the article

• Understanding how memory contents map into a struct

  - by user95592

  I am not able to understand how bytes in memory are being mapped into a struct. My machine is a little-endian x86_64. The code was compiled with gcc 4.7.0 from the Win64 mingw32-64 distribution for Win64. These are contents of the relevant memory fragment: ...450002cf9fe5000040115a9fc0a8fe... And this is the struct definition: typedef struct ip4 { unsigned int ihl :4; unsigned int version :4; uint8_t tos; uint16_t tot_len; uint16_t id; uint16_t frag_off; // flags=3 bits, offset=13 bits uint8_t ttl; uint8_t protocol; uint16_t check; uint32_t saddr; uint32_t daddr; /*The options start here. */ } ip4_t; When a pointer to such an structure (let it be *ip4) is initialized to the starting address of the above pasted memory region, this is what the debugger shows for the struct's fields: ip4: address=0x8da36ce ip4->ihl: address=0x8da36ce, value=0x5 ip4->version: address=0x8da36ce, value=0x4 ip4->tos: address=0x8da36d2, value=0x9f ip4->tot_len: address=0x8da36d4, value=0x0 ... I see how ihl and version are mapped: 4 bytes for a long integer, little-endian. But I don't understand how tos and tot_len are mapped; which bytes in memory correspond to each one of them. Thank you in advance.

  Read the article

• How can I make an infinite cave using stage3d?

  - by ifree

  I want to make an infinite cave in my 3d game using flash stage3d. But I got no idea about how to build that cave. Can anyone can give me some solution or hint? update: I've tried agal fragment shader like squeae tunnel in shader toy code: var fragmentProgramCode:String = AGALUtils.build() .mov("ft0","v0") .div("ft1","ft0.xy","fc3.xy") .mul("ft2","fc6.x","ft1") .sub("ft3","ft2","fc5.x")//vec2 p = -1.0 + 2.0 * gl_FragCoord.xy / resolution.xy; .mul("ft1","ft3.x","ft3.x") .mul("ft2","ft3.y","ft3.y") .pow("ft4","ft1","fc6.z")//float r = pow( pow(p.x*p.x,16.0) + pow(p.y*p.y,16.0), 1.0/32.0 ); .pow("ft5","ft2","fc6.z") .add("ft1","ft4","ft5") .pow("ft4","ft1","fc6.w") .mov("ft5","fc5")//uv .sub("ft1","fc7.x","ft4") .add("ft5.x","fc7.x","ft1")//uv.x = .5*time + 0.5/r; .mov("ft6","fc0")//for atan .atan2("ft5.y","ft3.y","ft3.x",new <String>["fc7.y","fc5.x","fc7.z","fc7.w","fc8.x","fc8.y","fc8.z","fc8.w","fc9.x","fc9.y"],"ft6") .tex("ft0","ft5","fs0","repeat","linear","nomip")//tex .mul("ft1","ft4","ft4") .mul("ft2","ft1","ft4")//r*r*r .mul("ft1","ft0.xyz","ft2") .mov("ft0.w","fc5.x") .mov("oc","ft1").toString() it can only apply one material,but my project requires different types of material (like floor,ceilling). so ,I create a 3d model Is there anyway to make that 3d model render like "infinity cave"? use agal to make each side of cave's texture move? thanks for your help

  Read the article

• OpenGL ES rotate texture

  - by 0xSina

  I just got started with OpenGL ES... I have a fragment: const char * sFragment = _STRINGIFY( varying highp vec2 coordinate; precision mediump float; uniform vec4 maskC; uniform float threshold; uniform sampler2D videoframe; uniform sampler2D videosprite; uniform vec4 mask; uniform vec4 maskB; uniform int recording; vec3 normalize(vec3 color, float meanr) { return color*vec3(0.75 + meanr, 1., 1. - meanr); } void main() { float d; float dB; float dC; float meanr; float meanrB; float meanrC; float minD; vec4 pixelColor; vec4 spriteColor; pixelColor = texture2D(videoframe, coordinate); spriteColor = texture2D(videosprite, coordinate); meanr = (pixelColor.r + mask.r)/8.; meanrB = (pixelColor.r + maskB.r)/8.; meanrC = (pixelColor.r + maskC.r)/8.; d = distance(normalize(pixelColor.rgb, meanr), normalize(mask.rgb, meanr)); dB = distance(normalize(pixelColor.rgb, meanrB), normalize(maskB.rgb, meanrB)); dC = distance(normalize(pixelColor.rgb, meanrC), normalize(maskC.rgb, meanrC)); minD = min(d, dB); minD = min(minD, dC); gl_FragColor = spriteColor; if (minD > threshold) { gl_FragColor = pixelColor; } } Now, depending on wether recording is 0 or 1, I want to rotate uniform sampler2D videosprite 180 degrees (reflection in x-axis, flip vertically). How can I do that? I found the function glRotatef(), but how do i specify that I want to rotate video sprite and not videoframe? Thanks

  Read the article

• Getting Unity 3D working on legacy Nvidia card

  - by user69545

  I installed the latest nVIDIA drivers for my FX5500 card. I understand that the X server version does not officially support this driver or card but was wondering what I can do to get compiz running. I have researched for hours on this issue but cannot come up with an answer for myself. I might be doing all this for nothing but I wanted to at least try. Here is the output of my test: mike@mike-linux-box:~$ /usr/lib/nux/unity_support_test -p OpenGL vendor string: NVIDIA Corporation OpenGL renderer string: GeForce FX 5500/AGP/SSE2 OpenGL version string: 2.1.2 NVIDIA 173.14.35 Not software rendered: yes Not blacklisted: no GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no So I was wondering what is the "Not Blacklisted" test? Is this the Nouveau Blacklisting? nVIDIA driver did that automatically. Does this need to be removed? Any help would be appreciated. I just want to run compiz effects. Thanks.

  Read the article

• How to automatically render all opaque meshes with a specific shader?

  - by dsilva.vinicius

  I have a specular outline shader that I want to be used on all opaque meshes of the scene whenever a specific camera renders. The shader is working properly when it is manually applied to some material. The shader is as follows: Shader "Custom/Outline" { Properties { _Color ("Main Color", Color) = (.5,.5,.5,1) _OutlineColor ("Outline Color", Color) = (1,0.5,0,1) _Outline ("Outline width", Range (0.0, 0.1)) = .05 _SpecColor ("Specular Color", Color) = (0.5, 0.5, 0.5, 1) _Shininess ("Shininess", Range (0.03, 1)) = 0.078125 _MainTex ("Base (RGB) Gloss (A)", 2D) = "white" {} } SubShader { Tags { "Queue"="Overlay" "RenderType"="Opaque" } Pass { Name "OUTLINE" Tags { "LightMode" = "Always" } Cull Off ZWrite Off // Uncomment to show outline always. //ZTest Always CGPROGRAM #pragma target 3.0 #pragma vertex vert #pragma fragment frag #include "UnityCG.cginc" struct appdata { float4 vertex : POSITION; float3 normal : NORMAL; }; struct v2f { float4 pos : POSITION; float4 color : COLOR; }; float _Outline; float4 _OutlineColor; v2f vert(appdata v) { // just make a copy of incoming vertex data but scaled according to normal direction v2f o; o.pos = mul(UNITY_MATRIX_MVP, v.vertex); float3 norm = mul ((float3x3)UNITY_MATRIX_IT_MV, v.normal); float2 offset = TransformViewToProjection(norm.xy); o.pos.xy += offset * o.pos.z * _Outline; o.color = _OutlineColor; return o; } float4 frag(v2f fromVert) : COLOR { return fromVert.color; } ENDCG } UsePass "Specular/FORWARD" } FallBack "Specular" } The camera used fot the effect has just a script component which setups the shader replacement: using UnityEngine; using System.Collections; public class DetectiveEffect : MonoBehaviour { public Shader EffectShader; // Use this for initialization void Start () { this.camera.SetReplacementShader(EffectShader, "RenderType=Opaque"); } // Update is called once per frame void Update () { } } Unfortunately, whenever I use this camera I just see the background color. Any ideas?

  Read the article

• There's IP but can't reach gateway

  - by icky

  I have just installed ubuntu 12.04 on my new laptop, and brought it back to home, but I found the wireless network does not work. Strangely, it has the correct ip, but can't connect to the gateway. ifconfig gives ip 192.168.64.36, with broadcast 192.168.79.255 and mask 255.255.240.0, this are all correct, the gateway is at 192.168.64.1 cat /etc/resolv.conf nameserver 192.168.64.1 nameserver 127.0.0.1 which i think it's also right. but when I ping 192.168.64.1, all packages are lost. Please help me with this, I really do not know what happened to my network settings. Huckle, Thank you for your reply ifconfig wlan0 Link encap:Ethernet Hwaddr 88:f9:af:2a:ca:1b inet addr:192.168.64.36 Bcast:192.168.79.255 Mask:255.255.240.0 inet6 addr: fe80::8a9f:faff:fea2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3950 TX byetes:60288 iwconfig wlan0 IEEE 802.11bgn ESSID:"Chiono" Mode:Managed Frequency:2.417 GHz Access Point: 82:54:99:94:6D:43 Bit Rate=13.5 Mb/s Tx-Power=13 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=70/70 Signal Level=-32 dBm Rx invalid nwid:0 Rx invalid crypt:0 RX invalid frag:0 Tx excessive retries: 9 Invalid misc:10 Missed beacon:0 route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.64.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.64.0 * 255.255.240.0 U 2 0 0 0 wlan0 Thank you very much

  Read the article

• GLSL Normals not transforming propertly

  - by instancedName

  I've been stuck on this problem for two days. I've read many articles about transforming normals, but I'm just totaly stuck. I understand choping off W component for "turning off" translation, and doing inverse/traspose transformation for non-uniform scaling problem, but my bug seems to be from a different source. So, I've imported a simple ball into OpenGL. Only transformation that I'm applying is rotation over time. But when my ball rotates, the illuminated part of the ball moves around just as it would if direction light direction was changing. I just can't figure out what is the problem. Can anyone help me with this? Here's the GLSL code: Vertex Shader: #version 440 core uniform mat4 World, View, Projection; layout(location = 0) in vec3 VertexPosition; layout(location = 1) in vec3 VertexColor; layout(location = 2) in vec3 VertexNormal; out vec4 Color; out vec3 Normal; void main() { Color = vec4(VertexColor, 1.0); vec4 n = World * vec4(VertexNormal, 0.0f); Normal = n.xyz; gl_Position = Projection * View * World * vec4(VertexPosition, 1.0); } Fragment Shader: #version 440 core uniform vec3 LightDirection = vec3(0.0, 0.0, -1.0); uniform vec3 LightColor = vec3(1f); in vec4 Color; in vec3 Normal; out vec4 FragColor; void main() { diffuse = max(0.0, dot(normalize(-LightDirection), normalize(Normal))); vec4 scatteredLight = vec4(LightColor * diffuse, 1.0f); FragColor = min(Color * scatteredLight, vec4(1.0)); }

  Read the article

• How can I avoid a 302 for Fetch as Bot?

  - by CookieMonster

  I originally posted this on Stackoverflow, but I believe here is a better place to ask. My web application is very similar to notepad.cc which redirects to a randomly generated URL upon access, e.g. http://myapp.com/roTr94h4Gd. (Please note that notepad.cc is not my site.) Probably because of this redirect feature, when I do "fetch as Google" or "fetch as Bingbot", I get a 302 and no html content. Not even a <html></html> tag. HTTP/1.1 302 Moved Temporarily Server: nginx/1.4.1 Date: Tue, 01 Oct 2013 04:37:37 GMT Content-Type: text/html Transfer-Encoding: chunked Connection: keep-alive X-Powered-By: PHP/5.4.17-1~dotdeb.1 Set-Cookie: PHPSESSID=vp99q5e5t5810e3bnnnvi6sfo2; expires=Thu, 03-Oct-2013 04:37:37 GMT; path=/ Expires: Thu, 19 Nov 1981 08:52:00 GMT Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma: no-cache Location: /roTr94h4Gd How should I avoid 302 in this case? I suppose I could modify my site to prevent the redirect, but it is a necessary feature of my web app to generate a random URL on each access. I added <meta name="fragment" content="!"> tag into my index page and set it to return a static snapshot of my page when the flag is set. But this still returns a 302. I also added a header to return 200 before redirecting, but this had no effect, either. Could someone tell me a good suggestion to solve this problem?

  Read the article

• How do I change until the next underscore in VIm?

  - by Nathan Long

  If I have this text in vim, and my cursor is at the first character: www.foo.com I know that I can do: cw to change up to the first period, because a word (lowercase w) ends at any punctuation OR white space cW to change the whole address, because a Word (uppercase w) ends only at whitespace Now, what if I have this: stupid_method_name and want to change it to this? awesome_method_name Both cw and cW change the whole thing, but I just want to change the fragment before the underscore. My fallback technique is c/_, meaning 'change until you hit the next underscore in a search,' but for me, that also causes all underscores to be highlighted as search terms, which is slightly annoying. Is there a specifier like w or W that doesn't include underscores?

  Read the article

• Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

  - by user1622959

  A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

  Read the article

• My internet connection slows or dies unexpectedly

  - by genesis

  I installed Ubuntu 10.04 once again and I'm having some problems which I had before, but I have no idea how I solved them. On Windows, everything's working fine and I had no problems with this. My problem is that sometimes, when browsing through the internet, webpages just start to load really slow, sometimes it doesn't load anything at all (Error 118 (net::ERR_CONNECTION_TIMED_OUT): The operation timed out.) and it starts to work after few minutes. My IPv4 settings are automatic (DHCP), and IPv6 settings are Ignored/Disabled. I think my previous problems had something to do with IPv6, but I'm not sure. Is there a fix for this? iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Fsite1" Mode:Managed Frequency:2.442 GHz Access Point: C8:3A:35:40:43:68 Bit Rate=0 kb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=43/70 Signal level=-67 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0

  Read the article

• Could someone explain why my world reconstructed from depth position is incorrect?

  - by yuumei

  I am attempting to reconstruct the world position in the fragment shader from a depth texture. I pass in the 8 frustum points in world space and interpolate them across fragments and then interpolate from near to far by the depth: highp float depth = (2.0 * CameraPlanes.x) / (CameraPlanes.y + CameraPlanes.x - texture( depthTexture, textureCoord ).x * (CameraPlanes.y - CameraPlanes.x)); // Reconstruct the world position from the linear depth highp vec3 world = mix( nearWorldPos, farWorldPos, depth ); CameraPlanes.x is the near plane CameraPlanes.y is the far. Assuming that my frustum positions are correct, and my depth looks correct, why is my world position wrong? (My depth texture is of format GL_DEPTH_COMPONENT32F if that matters) Thanks! :D Update: Screenshot of world position http://imgur.com/sSlHd So you can see it looks nearly correct. However as the camera moves, the colours (positions) change, which they shouldnt. I can get this to work, if I do the following: Write this into the depth attachment in the previous pass: gl_FragDepth = gl_FragCoord.z / gl_FragCoord.w / CameraPlanes.y; and then read the depth texture like so: depth = texture( depthTexture, textureCoord ).x However this will kill the hardware z buffer optimizations.

  Read the article

• Deferred rendering order?

  - by Nick Wiggill

  There are some effects for which I must do multi-pass rendering. I've got the basics set up (FBO rendering etc.), but I'm trying to get my head around the most suitable setup. Here's what I'm thinking... The framebuffer objects: FBO 1 has a color attachment and a depth attachment. FBO 2 has a color attachment. The render passes: Render g-buffer: normals and depth (used by outline & DoF blur shaders); output to FBO no. 1. Render solid geometry, bold outlines (as in toon shader), and fog; output to FBO no. 2. (can all render via a single fragment shader -- I think.) (optional) DoF blur the scene; output to the default frame buffer OR ELSE render FBO2 directly to default frame buffer. (optional) Mesh wireframes; composite over what's already in the default framebuffer. Does this order seem viable? Any obvious mistakes?

  Read the article

• Is a 302 redirect to a random URL from the homepage an SEO problem?

  - by CookieMonster

  I originally posted this on Stackoverflow, but I believe here is a better place to ask. My web application is very similar to notepad.cc which redirects to a randomly generated URL upon access, e.g. http://myapp.com/roTr94h4Gd. (Please note that notepad.cc is not my site.) Probably because of this redirect feature, when I do "fetch as Google" or "fetch as Bingbot", I get a 302 and no html content. Not even a <html></html> tag. HTTP/1.1 302 Moved Temporarily Server: nginx/1.4.1 Date: Tue, 01 Oct 2013 04:37:37 GMT Content-Type: text/html Transfer-Encoding: chunked Connection: keep-alive X-Powered-By: PHP/5.4.17-1~dotdeb.1 Set-Cookie: PHPSESSID=vp99q5e5t5810e3bnnnvi6sfo2; expires=Thu, 03-Oct-2013 04:37:37 GMT; path=/ Expires: Thu, 19 Nov 1981 08:52:00 GMT Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma: no-cache Location: /roTr94h4Gd How should I avoid 302 in this case? I suppose I could modify my site to prevent the redirect, but it is a necessary feature of my web app to generate a random URL on each access. I added <meta name="fragment" content="!"> tag into my index page and set it to return a static snapshot of my page when the flag is set. But this still returns a 302. I also added a header to return 200 before redirecting, but this had no effect, either. Could someone tell me a good suggestion to solve this problem?

  Read the article

• Questions before I revamp my rendering engine to use shaders (GLSL)

  - by stephelton

  I've written a fairly robust rendering engine using OpenGL ES 1.1 (fixed-function.) I've been looking into revamping the engine to use OpenGL ES 2.0, which necessitates that I use shaders. I've been absorbing information all day long and still have some questions. Firstly, lighting. The fixed-function pipeline is guaranteed to have at least 8 lights available. My current engine finds lights that are "close" to the primitives being drawn and enables them; I don't know how many lights are going to be enabled until I draw a given model. Nothing is dynamically allocated in GLSL, so I have to define in a shader some number of lights to be used, right? So if I want to stick with 8, should I write my general purpose shader to have 8 lights and then use uniforms to tell it how many / which lights to use? Which brings me to another question: should I be concerned with the amount of data I'm allocating in a shader? Recent video cards have hundreds of "stream processors." If I've got a fragment shader being used on some number of fragments in a given triangle, I assume they must each have their own stack to work on. Are read-only variables copied here, or read when needed? My initial goal is to rework my code so that it is virtually identical to the current implementation. What I have in mind is to create my own matrix stack so that I can implement something along the lines of push/popMatrix and apply all my translations, rotations, and scales to this matrix, then provide the matrix to the vertex shader so that it can make very quick vertex translations. Is this approach sound? Edit: My original intention was to ask if there was a tutorial that would explain the bare minimum necessary to jump from fixed-function to using shaders. Thanks!

  Read the article

• Views : ViewControllers, many to one, or one to one?

  - by conor

  I have developed an Android application where, typically, each view (layout.xml) displayed on the screen has it's own corresponding fragment (for the purpose of this question I may refer to this as a ViewController). These views and Fragments/ViewControllers are appropriately named to reflect what they display. So this has the effect of allowing the programmer to easily pinpoint the files associated with what they see on any given screen. The above refers to the one to one part of my question. Please note that with the above there are a few exceptions where very similar is displayed on two views so the ViewController is used for two views. (Using a simple switch (type) to determine what layout.xml file to load) On the flip side. I am currently working on the iOS version of the same app, which I didn't develop. It seems that they are adopting more of a one-to-many (ViewController:View) approach. There appears to be one ViewController that handles the display logic for many different types of views. In the ViewController are an assortment of boolean flags and arrays of data (to be displayed) that are used to determine what view to load and how to display it. This seems very cumbersome to me and coupled with no comments/ambiguous variable names I am finding it very difficult to implement changes into the project. What do you guys think of the two approaches? Which one would you prefer? I'm really considering putting in some extra time at work to refactor the iOS into a more 1:1 oriented approach. My reasoning for 1:1 over M:1 is that of modularity and legibility. After all, don't some people measure the quality of code based on how easy it is for another developer to pick up the reigns or how easy it is to pull a piece of code and use it somewhere else?

  Read the article

• Low Graphics and laggy screen after update to 13.10 from 13.04

  - by Wh0RU

  After updating from 13.04 to 13.10 many of 3D unity stuff has stopped working, I am suing Samsung Series 3 (NP350V5X) Laptop which has Switchable Intel and AMD Radeon HD 7670M GFX. xserver-xorg-video-ati does works but NO 3D support and graphics are very low. [I am currently using this] fglrx & fglrx-updates shows blank screen after Login. Intel Graphic Install doesn't work either (dependency error) Output of $ sudo lshw -c video *-display description: VGA compatible controller product: Thames [Radeon HD 7500M/7600M Series] vendor: Advanced Micro Devices, Inc. [AMD/ATI] physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:45 memory:e0000000-efffffff memory:c0120000-c013ffff ioport:3000(size=256) memory:c0100000-c011ffff *-display description: VGA compatible controller product: 3rd Gen Core processor Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:bfc00000-bfffffff memory:d0000000-dfffffff ioport:4000(size=64) Similarly $ /usr/lib/nux/unity_support_test -p OpenGL vendor string: VMware, Inc. OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 3.3, 256 bits) OpenGL version string: 2.1 Mesa 9.2.1 Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no Shows no 3D support. Can anyone please guide how to make things working again.

  Read the article

• AME : How to Diagnose Issues With the Default Approver List in Purchasing When Using Approvals Management

  - by Oracle_EBS

  Do you need help in understanding the concepts or how to setup the Approval Management Engine (AME) for requisition approvals? See the new diagnostic Note 1437183.1 'AME : How to Diagnose Issues With the Default Approver List in Purchasing When Using Approvals Management'. AME is designed to generate the approval list according to the conditions and rules you define in the setup. This troubleshooting guide will help you understand how AME builds the default approval list for Purchasing and help users find solutions for scenarios where the approval list fails to be generated. Follow along with the logical steps for troubleshooting.  The note first reviews how to generate the AME Setup report.   For example in the note we see a fragment of the setup report. Notice it has different sections for each one of the setup categories including attributes, conditions, rules, action types, approval groups etc.  How the default approval list is built in AME is then reviewed, followed by the logical steps for diagnosing issues.  The diagnostic steps include how to run the Test Workbench, as well as how to obtain valuable debug and exception information.  Then follow along using the steps to build a simple test case to sharpen your understanding.

  Read the article

• Adding root bone in 3DS Max?

  - by carlturtle

  my animation artist has made me a nice first person pair of arms, animated it, textured it, and given it to me. Then he went on vacation. I am programming my animations, and I am trying to test the model he has given me. Building my project gives me a warning: Multiple skeletons were found in the file. The first skeleton, named "frame l upperarm" has been moved to be a child of the scene root. The other, "frame r upperarm", will be ignored. Fragment identifier "frame r upperarm". Then an error: "Vertex is bound to bone "frame l forearm", but this bone is not present in the skeleton." I realize this means that there are two skeletons, as said in this problem: Importing 3d model with multiple skeletons I have 3DS Max, but I have no idea how to use it, and Google/CGTalk/Plycount turn up nothing relevant on how to add a root bone or combine skeletons. If anyone knows how, it would help me out greatly. Thanks.

  Read the article

• wireless blocked after installing ubuntu 12.04

  - by Cornelia Frank

  I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• Unity on Ubuntu 11.10 - The Dash Home button brings up the panel, but is empty

  - by David M. Coe

  The dash home button brings up a panel that is greyed out, but it is totally empty. It seems to be the very same issue as this: Dash home button brings up blank window which is unanswered. /usr/lib/nux/unity_support_test -p returns OpenGL vendor string: X.Org R300 Project OpenGL renderer string: Gallium 0.4 on ATI RV370 OpenGL version string: 2.1 Mesa 7.11 Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: yes I've tried a unity --reset but that doesn't seem to work. Unity seems to reset, but I get the following warning over and over: cs space validation failed unity What should I do next to try and fix this? Edit: Attempted fixes: I've refomatted, did not work. I've done apt-get remove unity then apt-get update then apt-get install unity, did not work. I've switched to Unity 2d and this seems to work. How can I get regualar Unity working or atleast find the error?

  Read the article

• Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

  - by jindrichm

  I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

  Read the article

• Graphics hardware warning when updating to 14.04

  - by pacomet

  As I use Ubuntu at work I just update only LTS versions but now I'm not sure if I can/should. As my computer is now ten years old I would change if was mine but as it is owned by my employer I have to work with it. It's not a bad one, it runs fine (this was not true when still had Windows on it ;-). When updating to 14.04, it warns about possible bad/slow performance with Unity 3D so I stop updating as I am at work, not my own computer. As I understand from http://askubuntu.com/a/438958/25305 Nvidia Geforce FX 5500 graphics card is still supported in 14.04. Now, in 12.04, I have driver version 173 and unity 2d runs fine for me. output of /usr/lib/nux/unity_support_test -p OpenGL vendor string: NVIDIA Corporation OpenGL renderer string: GeForce FX 5500/AGP/SSE2 OpenGL version string: 2.1.2 NVIDIA 173.14.39 Not software rendered: yes Not blacklisted: no GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no Should I update? Is it better to stay with 12.04? Thanks

  Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >