Search Results

Search found 3324 results on 133 pages for 'gb j'.

Page 18/133 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

  • ZFS with L2ARC (SSD) slower for random seeks than without L2ARC

    - by Florian Kruse
    I am currently testing ZFS (Opensolaris 2009.06) in an older fileserver to evaluate its use for our needs. Our current setup is as follows: Dual core (2,4 GHz) with 4 GB RAM 3x SATA controller with 11 HDDs (250 GB) and one SSD (OCZ Vertex 2 100 GB) We want to evaluate the use of a L2ARC, so the current ZPOOL is: $ zpool status pool: tank state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM afstank ONLINE 0 0 0 raidz1 ONLINE 0 0 0 c11t0d0 ONLINE 0 0 0 c11t1d0 ONLINE 0 0 0 c11t2d0 ONLINE 0 0 0 c11t3d0 ONLINE 0 0 0 raidz1 ONLINE 0 0 0 c13t0d0 ONLINE 0 0 0 c13t1d0 ONLINE 0 0 0 c13t2d0 ONLINE 0 0 0 c13t3d0 ONLINE 0 0 0 cache c14t3d0 ONLINE 0 0 0 where c14t3d0 is the SSD (of course). We run IO tests with bonnie++ 1.03d, size is set to 200 GB (-s 200g) so that the test sample will never be completely in ARC/L2ARC. The results without SSD are (average values over several runs which show no differences) write_chr write_blk rewrite read_chr read_blk random seeks 101.998 kB/s 214.258 kB/s 96.673 kB/s 77.702 kB/s 254.695 kB/s 900 /s With SSD it becomes interesting. My assumption was that the results should be in worst case at least the same. While write/read/rewrite rates are not different, the random seek rate differs significantly between individual bonnie++ runs (between 188 /s and 1333 /s so far), average is 548 +- 200 /s, so below the value w/o SSD. So, my questions are mainly: Why do the random seek rates differ so much? If the seeks are really random, they should not differ much (my assumption). So, even if the SSD is impairing the performance it should be the same in each bonnie++ run. Why is the random seek performance worse in most of the bonnie++ runs? I would assume that some part of the bonnie++ data is in the L2ARC and random seeks on this data performs better while random seeks on other data just performs similarly like before.

    Read the article

  • Tidy up old Windows Server Backup snapshots

    - by dty
    Hi, I'm running wbadmin from a scheduled job, backing up my C: and D: drives to my E: and (I believe!) including the system state: wbadmin start backup -backuptarget:e: -include:c:,d: -allCritical -noVerify -quiet I'd like to delete old backups, but I'm concerned that all the information I can find says to use wbadmin to delete old system state backups, and vssadmin to delete other backups. As far as I know, my backups ARE system state backups, but are using VSS on E: for storage, so I'm worried about trying either of these techniques for fear of losing all my backups. This is a home network, so I don't have a spare server to test this on. I'm also happy to simply restrict the space used on E:, but I can't make sense of the difference between the /for and /on parameters of the relevant vssadmin command. For reference, here's the output of vssadmin show shadows: Contents of shadow copy set ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Contained 1 shadow copies at creation time: 07/01/2011 08:12:05 Shadow Copy ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Original Volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Volume: \\?\GLOBALROOT\Device\HarddiskVolumeShadowCopy83 Originating Machine: x.y.com Service Machine: x.y.com Provider: 'Microsoft Software Shadow Copy provider 1.0' Type: DataVolumeRollback Attributes: Persistent, No auto release, No writers, Differential [... repeated a lot...] vssadmin show shadowstorage: Shadow Copy Storage association For volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 5.859 GB Shadow Copy Storage association For volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 40.317 GB Shadow Copy Storage association For volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 168.284 GB Allocated Shadow Copy Storage space: 171.15 GB Maximum Shadow Copy Storage space: UNBOUNDED wbadmin get versions: Backup time: 07/01/2011 03:00 Backup target: 1394/USB Disk labeled xxxxxxxxx(E:) Version identifier: 01/07/2011-03:00 Can Recover: Volume(s), File(s), Application(s), Bare Metal Recovery, System State [... repeated a lot...]

    Read the article

  • Slow performance of MySQL database on one server and fast on another one, with similar configurations

    - by Alon_A
    We have a web application that run on two servers of GoDaddy. We experince slow preformance on our production server, although it has stronger hardware then the testing one, and it is dedicated. I'll start with the configurations. Testing: CentOS Linux 5.8, Linux 2.6.18-028stab101.1 on i686 Intel(R) Xeon(R) CPU L5609 @ 1.87GHz, 8 cores 60 GB total, 6.03 GB used Apache/2.2.3 (CentOS) MySQL 5.5.21-log PHP Version 5.3.15 Production: CentOS Linux 6.2, Linux 2.6.18-028stab101.1 on x86_64 Intel(R) Xeon(R) CPU L5410 @ 2.33GHz, 8 cores 120 GB total, 2.12 GB used Apache/2.2.15 (CentOS) MySQL 5.5.27-log - MySQL Community Server (GPL) by Remi PHP Version 5.3.15 We are running the same code on both servers. The Problem We have some function that executes ~30000 PDO-exec commands. On our testing server it takes about 1.5-2 minutes to complete and our production server it can take more then 15 minutes to complete. As you can see here, from qcachegrind: Researching the problem, we've checked the live graphs on phpMyAdmin and discovered that the MySQL server on our testing server was preforming at steady level of 1000 execution statements per 2 seconds, while the slow production MySQL server was only 250 executions statements per 2 seconds and not steady at all, jumping from 0 to 250 every seconds. You can clearly see it in the graphs: Testing server: Production server: You can see here the comparison between both of the configuration of the MySQL servers.Left is the fast testing and right is the slow production. The differences are highlighted, but I cant find anything that can cause such a behavior difference, as the configs are mostly the same. Maybe you can see something that I cant see. Note that our tables are all InnoDB, so the MyISAM difference is (probably) not relevant. Maybe it is the MySQL Community Server (GPL) that is installed on the production server that can cause the slow performance? Or maybe it needs to be configured differently for 64bit ? I'm currently out of ideas...

    Read the article

  • How to properly remove disk from PERC 6/i RAID controller ?

    - by Stefano Borini
    I have a Dell T710, coming with PERC 6/i RAID controller. The current raid has 2x500 GB hard drives (with the OS), and 6x1000 GB hard drives (in RAID-6, currently empty). I would like to take one 1000 GB disk physically out to keep as an immediate spare in case of a crash, and configure the remaining 5x1000 GB in a single VD RAID-6. This is all nice and clean and works, until I realized that the display on the machine reports the lack of the 8th disk as an error. It's marked as error, but appears to be a warning, since the machine is fully functional. My question is: what is the best way to keep one disk as a spare out of the array? should I disassemble the disk from the cradle and insert the empty cradle in the array ? Or should I just silence the error in the display in some way (how?). I know that what I am doing sounds pretty strange, but here is academia and having a spare disk available could take weeks. Better to have one ready in my drawer for any emergency.

    Read the article

  • "A disk read error occurred" after choosing to boot into Windows XP from GRUB

    - by kellogs
    "A disk read error occurred" appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris Here, sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I cannot recall how exactly have I used testdisk but it once said: Disk /dev/sda - 160 GB / 149 GiB - CHS 19458 255 63 The harddisk (160 GB / 149 GiB) seems too small! (< 169 GB / 157 GiB) Check the harddisk size: HD jumper settings, BIOS detection... So far I have tried to "fixboot" and "chkdsk" from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please? Thank you!

    Read the article

  • SQL Server becomes slow after restart

    - by Tobi DM
    I already posted this one on stackoverflow but someone gave me the hint to that I might have more luck on serverfault. We use SQL Server 2005 on an Windwos Server 2008. Ther Server has 48 GB RAM. SQL Server is configured to use 40 GB RAM. There is only one database hosted (About 70 GB). The only app beside SQL Server is our App-Server which connects the clients to the database. Now we encounter the following problem: After a restart of the server our the performance is great. The server grabs the 40 GB RAM wich it is allowed to and then runs fast as hell. But after about 4 weeks the system becomes slower and slower. The execution of statements (seen in the profiler) is raising slowly. But I cannot see that there is something going wrong on the server. CPU usage is at about 20% I/O also seems to be no Problem The process monitor does also not show that there are strange apps or something like that. Eventlog does also have no interessting messages No open transactions or blockings to see We do not use cursors in our app We tried already the following things without effect: Droped the cache by using the statements DBCC FreeProcCache DBCC FREESYSTEMCACHE('ALL') DBCC DropCleanbuffers Restarted the Appserver we are using. Restart the sql server service But nothing did help exept restarting the whole server. Any ideas?

    Read the article

  • Compressing and copying large files on Windows Server?

    - by Aaron
    I've been having a hard time copying large database backups from the database server to a test box at another site. I'm open to any ideas that would help me get this database moved without having to resort to a USB hard drive and the mail. The database server is running Windows Server 2003 R2 Enterprise, 16 GB of RAM and two quad-core 3.0 GHz Xeon X5450s. Files are SQL Server 2005 backup files between 100 GB and 250 GB. The pipe is not the fastest and SQL Server backup files typically compress down to 10-40% of the original, so it made sense to me to compress the files first. I've tried a number of methods, including: gzip 1.2.4 (UnxUtils) and 1.3.12 (GnuWin) bzip2 1.0.1 (UnxUtils) and 1.0.5 (Cygwin) WinRAR 3.90 7-Zip 4.65 (7za.exe) I've attempted to use WinRAR and 7-Zip options for splitting into multiple segments. 7za.exe has worked well for me for database backups on another server, which has ~50 GB backups. I've also tried splitting the .BAK file first with various utilities and compressing the resulting segments. No joy with that approach either- no matter the tool I've tried, it ends up butting against the size of the file. Especially frustrating is that I've transferred files of similar size on Unix boxes without problems using rsync+ssh. Installing an SSH server is not an option for the situation I'm in, unfortunately. For example, this is how 7-Zip dies: H:\dbatmp>7za.exe a -t7z -v250m -mx3 h:\dbatmp\zip\db-20100419_1228.7z h:\dbatmp\db-20100419_1228.bak 7-Zip (A) 4.65 Copyright (c) 1999-2009 Igor Pavlov 2009-02-03 Scanning Creating archive h:\dbatmp\zip\db-20100419_1228.7z Compressing db-20100419_1228.bak System error: Unspecified error

    Read the article

  • Ubuntu cannot resolve unmet dependency

    - by DisgruntledGoat
    I'm trying to install a package on my Ubuntu 8.10 server. However, I get this message: The following packages have unmet dependencies. webmin: Depends: apt-show-versions but it is not going to be installed E: Unmet dependencies. Try ‘apt-get -f install’ with no packages (or specify a solution). So I run apt-get -f install which offers to install apt-show-versions and libapt-pkg-perl. After selecting to install without verification, I get these errors: Err http://gb.archive.ubuntu.com intrepid/universe libapt-pkg-perl 0.1.22build1 404 Not Found Err http://gb.archive.ubuntu.com intrepid/universe apt-show-versions 0.13 404 Not Found Failed to fetch http://gb.archive.ubuntu.com/ubuntu/pool/universe/liba/libapt-pkg-perl/libapt-pkg-perl_0.1.22build1_i386.deb 404 Not Found Failed to fetch http://gb.archive.ubuntu.com/ubuntu/pool/universe/a/apt-show-versions/apt-show-versions_0.13_all.deb 404 Not Found E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? I've tried running apt-get update and adding --fix-missing as suggested, but neither works. Where do I go from here?

    Read the article

  • Regarding partitions for dual-booting Ubuntu with pre-existing Windows 7

    - by Shasteriskt
    I have zero actual experience with configuring disk partitions and the stuff I have read for the past few hours have been confusing me a bit, so please bear with me. First of all, I'd like to explain what I'm setting to achieve: Windows 7 with: C:\ Windows 7 (pre-existing installation) D:\ Data (Already exists and has files already) Ubuntu 11 - Does not exist yet, but I already have a LiveCD in hand. \root directory for Ubuntu \home on its own partition I plan \swap on its own partition with around 8GB Here is the current situation: I have a single 500 GB hard-disk with Windows 7 x64 installed, and the current partition schemes is as follows: System Reserved: 100 MB (Primary, Active) C: 100 GB - Where Windows 7 is installed (Primary) D: 365 GB - Where my files are located, LOTS of free space (Primary) Now, I would like to shrink my D: drive and create around 40 GB of unallocated disk space for the Ubuntu installation, but here what's confusing me a bit: I'm thinking I would create an extended partition and subdivide it into 3 logical partitions for the Ubuntu setup I had in mind. (If you think my setup is a bad idea, please let me know & why. I also hope you can suggest a better one...) I am aware that I can only have up to 4 primary partitions, or 3 primary partitions with 1 extended parition max. Now, does the System Recovery portion count as one primary partition? I'm really new to these things and it is totally unclear to me. In shrinking my D: drive using Windows 7's Disk Management tool, I would get an unallocated free space which I don't know how to make an extended partition from. It seems like I can only create a primary partition from it, not an extended one. How do I go about it? (I'd also like to note, if it is of any importance, that I am trying to avoid using the option to install Ubuntu alongside Windows, and much rather prefer using the custom install where I can specify which drives I wish to use and stuff. Somehow I feel its safer that way.)

    Read the article

  • SSD suddenly full

    - by Daniel
    Today the hard drive of our server was suddenly full. The disk usage always stayed around 50 % in the weeks and months before (old data is regularly expunged from the server). I deleted 10 GB of files in /tmp, which strangely freed 51 GB. Here is what I did: root@***:~# df -h Dateisystem Size Used Avail Use% Eingehängt auf /dev/sda3 139G 137G 0 100% / tmpfs 3,9G 0 3,9G 0% /lib/init/rw udev 3,9G 116K 3,9G 1% /dev tmpfs 3,9G 0 3,9G 0% /dev/shm /dev/sda1 985M 25M 910M 3% /boot root@***:/var# du -hs * 3,3M backups 438M cache 9,4G lib 4,0K local 12K lock 76M log 24K mail 4,0K opt 88K run 184K spool 10G tmp 12K www root@***:/var/tmp# find -type f -print0 | xargs -0 rm root@***:/var/tmp# df -h Dateisystem Size Used Avail Use% Eingehängt auf /dev/sda3 139G 81G 51G 62% / tmpfs 3,9G 0 3,9G 0% /lib/init/rw udev 3,9G 116K 3,9G 1% /dev tmpfs 3,9G 0 3,9G 0% /dev/shm /dev/sda1 985M 25M 910M 3% /boot Any explanation as to why deleting 10 GB in /tmp gave me back 51 GB on the disk? Could this point to an SSD failure? Are there any tools for Debian to test SSD health? I already have checked syslog. The first entry relating to this incidient is a mysql message: 1:22:02 [ERROR] /usr/sbin/mysqld: Disk is full writing... So I have absolutely no idea what caused this.

    Read the article

  • Ubuntu cannot resolve unmet dependency

    - by DisgruntledGoat
    I'm trying to install a package on my Ubuntu 8.10 server. However, I get this message: The following packages have unmet dependencies. webmin: Depends: apt-show-versions but it is not going to be installed E: Unmet dependencies. Try ‘apt-get -f install’ with no packages (or specify a solution). So I run apt-get -f install which offers to install apt-show-versions and libapt-pkg-perl. After selecting to install without verification, I get these errors: Err http://gb.archive.ubuntu.com intrepid/universe libapt-pkg-perl 0.1.22build1 404 Not Found Err http://gb.archive.ubuntu.com intrepid/universe apt-show-versions 0.13 404 Not Found Failed to fetch http://gb.archive.ubuntu.com/ubuntu/pool/universe/liba/libapt-pkg-perl/libapt-pkg-perl_0.1.22build1_i386.deb 404 Not Found Failed to fetch http://gb.archive.ubuntu.com/ubuntu/pool/universe/a/apt-show-versions/apt-show-versions_0.13_all.deb 404 Not Found E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? I've tried running apt-get update and adding --fix-missing as suggested, but neither works. Where do I go from here?

    Read the article

  • IBM BladeCenter S: Disk Configuration

    - by gravyface
    Have just the one storage bay right now (SAS 15K 600GB x 6) and have configured one storage pool in RAID 10 with 4 disks (and two global spares). For each blade, I've created a volume and mapped accordingly: Blade #1 400 GB Blade #2 200 GB Blade #3 100 GB Blade #4 100 GB When I boot up Blade 1 and enter into the UEFI Setup (F1) followed by the Adapters and UEFI Drivers LSI Logic Fusion MPT SAS Driver Utility, I see 4 disks: two are the on-board 73GB drives, the other two are 200GB each and assume I'm being presented with two logical disks from the volume I created and mapped to this blade. I was a bit surprised by this: I figured I would've been presented with one logical drive per volume, not two. I'm assuming I can just configure whatever RAID level I wish that supports two disks, but not really sure what the benefits/trade-offs here. Should I go with RAID 10 on top of RAID 10? RAID 0? Software RAID 0/1/10? Does it even matter? If this is "normal" to see two disks, then I'm going to likely just do some benchmarking and see if it makes a difference changing the RAID levels (my guess is no); if this is not normal, well, please let me know. :)

    Read the article

  • Disk doesn't contain a valid partition table

    - by Jeevan Dongre
    I was running a m1.small instance ec2 ubuntu instance. I was running out of disk space, so I upgraded my instance to medium. When I upgraded I actually got 429.5 GB of space and after that I added 10 gb of volume too. When I run the "sudo fdisk -l" command I got this results. Disk /dev/sda1: 8589 MB, 8589934592 bytes 255 heads, 63 sectors/track, 1044 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda1 doesn't contain a valid partition table Disk /dev/sda2: 429.5 GB, 429461078016 bytes 255 heads, 63 sectors/track, 52212 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda2 doesn't contain a valid partition table Disk /dev/sdf: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 sda1 is the primary parition and sda2 is what I got added upgrading my system to medium. But the problem persists, I am not able to pull the code from git, it is giving me this error. remote: Counting objects: 409, done. remote: Compressing objects: 100% (236/236), done. fatal: write error: No space left on device fatal: index-pack failed

    Read the article

  • Move EFI System Partition to another drive

    - by Pincopallino
    I had a Windows 8 installation on an HDD, using UEFI as boot. The HDD has the following GPT table: DISKPART> list partition Partizione ### Tipo Dim. Offset --------------- ---------------- ------- ------- Partizione 1 Ripristino 300 Mb 1024 Kb Partizione 2 Sistema 100 Mb 301 Mb Partizione 3 Riservato 128 Mb 401 Mb Partizione 4 Primario 390 Gb 529 Mb Partizione 5 Primario 540 Gb 390 Gb (I apologize it's in Italian, but the translation is quite straightforward). I recently bought an SSD drive, connected it and installed a fresh Windows 8. Now I have a working dual boot, but the UEFI partition is on the HDD instead of the SSD. Here's the SDD partition list: Partizione ### Tipo Dim. Offset --------------- ---------------- ------- ------- Partizione 1 Riservato 128 Mb 1024 Kb Partizione 2 Primario 221 Gb 129 Mb I think that the best solution would be to have it on the SSD for two reasons: the first is performance (I guess it would be a little be faster on the SSD due to the spin up time for an HDD, but I may be wrong about that) second reason is consistency. As I plan to use only the Windows 8 installation that is located on the SSD and I'm probably going to erase the system partition on the HDD to use it as a data storage device, I think that the boot partition should be on the same drive as the OS. So the question is how do I move the EFI System Partition to the SSD?

    Read the article

  • My new SSD is causing issues. How can I solve them?

    - by Allan
    Computer specs 1 TB harddisc 120 GB 520intel SSD 8 GB DDR3 RAM Athlon Phenom II x64 955 3. 2ghz DK DFI Lanparty FX7900 M3H3 motherboard ASUS ATI RADEON HD6970 2 GB I have bought a new SSD (Intel 520, 120 GB), and wanted to use this as my system disc. I removed the other harddisc, and installed the SSD with the newest firmware. And then Windows 7 I updated Windows 7 with no problems and then put back my old harddrive. I formatted that old harddrive just to clean up at the same time... So at this stage everything was perfect. My new SSD was set as Master 0 Primary it boots on it and I have 1 TB emptyu harddrive I can use for whatever I want. So far no errors at all Now here is the problem, I installed a few games and everytime I tried to play the computer would say Windows must restart because DCOM server process launcher service terminated, or it says Windows must now restart because the Plug and Play service terminated unexpectedly Most commonly this error is caused by a rootkit virus, well I have tried formatting my entire computer, and running every antivirus I could find, so that shouldn't be it. I've also read somewhere it might happen when there are hardware issues. That on the otherhand would make sense, as I just put in a new SSD. I don't expect you to know this error. I haven't found anyone who knew it yet. maybe you can me guide through what might have gone wrong when I placed in the SSD? What have I checked regarding the SSD? It displays the right name when the computer starts up It has the newest firmware Did a 'sfc /scannow' which told me everything was fine I don't know what to do from here. Everything seems to work great with the drive. when I start playing games my computer crashes.

    Read the article

  • Can't mount hard drive. Ubuntu 12.04

    - by Sam
    I am trying to recover some pictures on my 320 GB Hard Disk, so I put in a Live Ubuntu CD and am in that right now. In the devices list, it shows my USB drive, but not my 320 GB Hard Disk. I can see the disk in Disk Utility (it says it's on /dev/sda), but it's not mounted, and it says it has a few bad sectors but it is OK. In Disk Usage Analyzer, it says my maximum capacity is 13.4 GB, so it's definitely not using the 320 GB Hard Disk. I tried the following: sudo mkdir /media/newhd (worked) sudo mount /dev/sda /media/newhd (didn't work. it says I must specify the filesystem type) I then tried: fsck.ext4 -f /dev/sda (didn't work. Said: Superblock invalid, trying to backup blocks. then: Bad magic number in super-block while trying to open /dev/sda. The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock) Does anyone have any ideas? The whole problem started when my Windows Vista said "Can't find operating system". Any ideas on how I can get on to my hard drive at /dev/sda?

    Read the article

  • Cloning to a smaller hard drive with DDRescue

    - by krebshack
    I am currently working with a 700 GB Seagate hard drive that's beginning to fail. I'll call this "SDB" from now on. I'd like to clone it while I'm still able to. However, the only hard drive that I have available is a 500 GB WD hard drive. I'll call this "SDC" from now on. The partition scheme on SDB is as follows: 9.77 GB is allocated to a recovery partition and the remaining 688.87 GB is allocated to a Windows partition. Both are formatted using NTFS. There is no partition scheme on SDC. I know how to clone one hard drive to another using DDRescue but I've only done it using hard drives that are the same size. For your reference, I'll normally use the command "ddrescue -v -r 3 /dev/sdb /dev/sdc example.log". I'd like to know if it's possible to do this with DDRescue. I've read the manual from GNU (http://www.gnu.org/software/ddrescue/manual/ddrescue_manual.html) and I haven't seen anything indicating that it is possible. I'm just looking for some confirmation that this is a correct impression. If it's not possible, then it would be helpful if any of y'all would be able to make some work around suggestions. But please don't feel obligated to do that. I don't want to have my one thread bogged down with two many questions.

    Read the article

  • Best format for hard drive for Windows and Mac?

    - by Neil
    I have a 500 GB USB External Hard Drive. I need four partitions on it, for the following purposes: 160 GB for a bootable backup of my Mac. 160 GB for a bootable backup of my Windows. 11 GB for a bootable Snow Leopard Install Disk Rest as for file storage. Now I need a partition table which will get recognised on both Windows and Mac, without needing extra software on Windows, which will let me keep bootable copies of both OS'es, but let me access the file storage from both OS'es. Currently, I have a GUI Partition Table, with Mac OS Extended (Journaled) Partitions for the two backups, Mac OS Extended for the Install Disk, and NTFS for the file storage. While this gets recognised perfectly on my Mac, thanks to an NTFS for Mac driver from Paragon, when connected to Windows, the drive is detected by the machine (listed in Safely Remove USB), but not recognised in Windows Explorer unless I install MacDrive, which is not feasible for me to install on public Windows Machines I might wanna access my storage area on. Can someone recommend the best combination of formats and software/drivers to get this done seamlessly?

    Read the article

  • Server periodically freezing - Help Stabilizing

    - by JonDog
    We run an asp.net/sql server data collection website with a hand full of clients dumping data in and running reports. We moved to a new server (specs below) and have had issues with it freezing and having to reboot it a dozen times over the pass six months. The hosting company has mentioned possible causes (listed below) but cant give a definite answer on what is going wrong. They have offered to reconfigure how ever I like. We have benefited from having a much faster system and really dont want to get rid of the ssd's unless they are the issue. Two possible setup changes that I've talked with them about are also listed below. Any suggestions on what maybe causing the freezing issue as well as suggestion on a new setup would be great. My main questions are: Do SSD generally have problems running the OS & SQL Server on the same RAID Array? and Are the new SSD's still unrefined enough to be running in a production environment? Thanks Current: Xeon Quad Core E3-1270 3.40 Ghz 16 GB DDR3-1333 ECC SDRAM First Hard Drive: 120GB Intel SSD Second Hard Drive: 120GB Intel SSD Third Hard Drive: 120GB Intel SSD Fourth Hard Drive: 120GB Intel SSD SAS 4 Port RAID Card Windows 2012 Standard Edition - 64 Bit MSSQL 2008 Web Edition Possible Causes: Running Sql Server & OS on same RAID Array OS Software Issues Using SSD's CPU Underpowered Not enough RAM Option 1 2x Xeon Quad Core E5-2603 1.80 GHz 16 GB DDR3-1333 ECC SDRAM 1 x 240GB Intel SSD - OS 3 x 1 TB SATA HDD (7200 RPM) - SQL Server SATA 4 Port RAID Card Windows 2012 Standard Edition - 64 Bit Option 2 Dell PowerEdge E3-1270v2 3.5GHz 4 Cores 16 GB DDR3-1600 UDIMM 4 x 128 GB Samsung 840 Pro SSD Add-in H200 (SAS/SATA Controller), 4 Hard Drives - RAID 10 Windows 2012 Standard Edition - 64 Bit

    Read the article

  • How can I extend / create a new partition from the following setup?

    - by Kiada
    I'm a little unsure what to do in this situation. When I try to create a new simple volume from the unallocated space I get an error because I already have 4 partitions. I have no option to extend either my C:\ primary partition or the E:\ logical drive. C:\ - Gaming Win7 install. D:\ - Storage Unallocated Space - Would somehow like to install OSX on a partition from this space. E:\ - Software Development Win7 install. I:\ - Ignore this. It's an external 1TB HDD. Do I have any options that do not involve formatting / losing information on either C:\ or E:\? Thank you. Link to visual disk partitioning setup image. Edit: A bit more information regarding partitions. Firstly, the image linked above is a screenshot of Windows 7 partitioning tool, easier to read than text I guess! H:\ System Reserved: 100MB NTFS C:\ 244 GB NTFS Healthy (Page File, Primary Partition) D:\ 294 GB NTFS Healthy (Primary Partition) E:\ 100 GB NTFS Healthy (Boot, Page File, Crash Dump, Logical Drive) Unallocated 292 GB Hope this helps :)

    Read the article

  • Restore only one partition of Windows Backup

    - by VitoShadow
    I have a MacBook Pro with an HD partitioned. This HD was divided in two partitions: the first was about 650 GB, with OS X installed, and the second one (created with BootCamp Assistant) was about 100 GB, with Windows 7 installed. I needed more space for Windows, so I decided to backup the Windows partition using the Windows backup tool, from Control Panel. I created an image of my partition, stored it in an external HD, and now I'm trying to use it. In order to give more space to Windows, I formatted the HD, and recreate a new partition table, with the first partition of about 250 GB (with OS X) and the second of the exactly size of the previous partition in which was installed Windows (about 100 GB); thre rest was empty space. In the second, I tried to restore the Windows backup. I plugged in the Windows Installation CD (with the HD with the backup connected to the computer), and select the option "Repair your computer". Then, I choose the image of the backup (automatically recognized), and I try to restore it. The problem is that now the System Recovery Tool wants to format all the HD, in order to install only Windows! In this way, I should lose everything, also the MacOS partition! Is there a way to install the backup only in the Windows partition?

    Read the article

  • Grub 'Read Error' - Only Loads with LiveCD

    - by Ryan Sharp
    Problem After installing Ubuntu to complete my Windows 7/Ubuntu 12.04 dual-boot setup, Grub just wouldn't load at all unless I boot from the LiveCD. Afterwards, everything works completely normal. However, this workaround isn't a solution and I'd like to be able to boot without the aid of a disc. Fdisk -l Using the fdisk -l command, I am given the following: Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x324971d1 Device Boot Start End Blocks Id System /dev/sda1 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 208896 48957439 24374272 7 HPFS/NTFS/exFAT /dev/sda3 * 48959486 124067839 37554177 5 Extended /dev/sda5 48959488 124067839 37554176 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc0ee6a69 Device Boot Start End Blocks Id System /dev/sdb1 1024208894 1953523711 464657409 5 Extended /dev/sdb3 * 2048 1024206847 512102400 7 HPFS/NTFS/exFAT /dev/sdb5 1024208896 1937897471 456844288 83 Linux /dev/sdb6 1937899520 1953523711 7812096 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/sdc: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x292eee23 Device Boot Start End Blocks Id System /dev/sdc1 2048 625141759 312569856 7 HPFS/NTFS/exFAT Bootinfoscript I've used the BootInfoScript, and received the following output: Boot Info Script 0.61 [1 April 2012] ============================= Boot Info Summary: =============================== => Grub2 (v1.99) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. => Grub2 (v1.99) is installed in the MBR of /dev/sdb and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. => Windows is installed in the MBR of /dev/sdc. sda1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /bootmgr /Boot/BCD sda2: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe sda3: __________________________________________________________________________ File system: Extended Partition Boot sector type: Unknown Boot sector info: sda5: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 12.04.1 LTS Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdb1: __________________________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sdb5: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Boot files: sdb6: __________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: sdb3: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: According to the info in the boot sector, sdb3 starts at sector 200744960. But according to the info from fdisk, sdb3 starts at sector 2048. According to the info in the boot sector, sdb3 has 823461887 sectors, but according to the info from fdisk, it has 1024204799 sectors. Operating System: Boot files: sdc1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 2,048 206,847 204,800 7 NTFS / exFAT / HPFS /dev/sda2 208,896 48,957,439 48,748,544 7 NTFS / exFAT / HPFS /dev/sda3 * 48,959,486 124,067,839 75,108,354 5 Extended /dev/sda5 48,959,488 124,067,839 75,108,352 83 Linux Drive: sdb _____________________________________________________________________ Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdb1 1,024,208,894 1,953,523,711 929,314,818 5 Extended /dev/sdb5 1,024,208,896 1,937,897,471 913,688,576 83 Linux /dev/sdb6 1,937,899,520 1,953,523,711 15,624,192 82 Linux swap / Solaris /dev/sdb3 * 2,048 1,024,206,847 1,024,204,800 7 NTFS / exFAT / HPFS Drive: sdc _____________________________________________________________________ Disk /dev/sdc: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdc1 2,048 625,141,759 625,139,712 7 NTFS / exFAT / HPFS "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/sda1 A48056DF8056B80E ntfs System Reserved /dev/sda2 A8C6D6A4C6D671D4 ntfs Windows /dev/sda5 fd71c537-3715-44e1-b1fe-07537e22b3dd ext4 /dev/sdb3 6373D03D0A3747A8 ntfs Steam /dev/sdb5 6f5a6eb3-a932-45aa-893e-045b57708270 ext4 /dev/sdb6 469848c8-867a-41b7-b0e1-b813a43c64af swap /dev/sdc1 725D7B961CF34B1B ntfs backup ================================ Mount points: ================================= Device Mount_Point Type Options /dev/sda5 / ext4 (rw,noatime,nodiratime,discard,errors=remount-ro) /dev/sdb5 /home ext4 (rw) =========================== sda5/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd set locale_dir=($root)/boot/grub/locale set lang=en_GB insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="${1}" if [ "${1}" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ "${recordfail}" != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "${linux_gfx_mode}" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.2.0-29-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd linux /boot/vmlinuz-3.2.0-29-generic root=UUID=fd71c537-3715-44e1-b1fe-07537e22b3dd ro quiet splash $vt_handoff initrd /boot/initrd.img-3.2.0-29-generic } menuentry 'Ubuntu, with Linux 3.2.0-29-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd echo 'Loading Linux 3.2.0-29-generic ...' linux /boot/vmlinuz-3.2.0-29-generic root=UUID=fd71c537-3715-44e1-b1fe-07537e22b3dd ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.2.0-29-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows 7 (loader) (on /dev/sda1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root A48056DF8056B80E chainloader +1 } menuentry "Windows 7 (loader) (on /dev/sda2)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root A8C6D6A4C6D671D4 chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- =============================== sda5/etc/fstab: ================================ -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda5 during installation UUID=fd71c537-3715-44e1-b1fe-07537e22b3dd / ext4 noatime,nodiratime,discard,errors=remount-ro 0 1 # /home was on /dev/sdb5 during installation UUID=6f5a6eb3-a932-45aa-893e-045b57708270 /home ext4 defaults 0 2 # swap was on /dev/sdb6 during installation UUID=469848c8-867a-41b7-b0e1-b813a43c64af none swap sw 0 0 tmpfs /tmp tmpfs defaults,noatime,mode=1777 0 0 -------------------------------------------------------------------------------- =================== sda5: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) = boot/grub/core.img 1 = boot/grub/grub.cfg 1 = boot/initrd.img-3.2.0-29-generic 2 = boot/vmlinuz-3.2.0-29-generic 1 = initrd.img 2 = vmlinuz 1 ======================== Unknown MBRs/Boot Sectors/etc: ======================== Unknown BootLoader on sda3 00000000 63 6f 70 69 61 20 65 20 63 6f 6c 61 41 63 65 64 |copia e colaAced| 00000010 65 72 20 61 20 74 6f 64 6f 20 6f 20 74 65 78 74 |er a todo o text| 00000020 6f 20 66 61 6c 61 64 6f 20 75 74 69 6c 69 7a 61 |o falado utiliza| 00000030 6e 64 6f 20 61 20 63 6f 6e 76 65 72 73 c3 a3 6f |ndo a convers..o| 00000040 20 64 65 20 74 65 78 74 6f 20 70 61 72 61 20 76 | de texto para v| 00000050 6f 7a 4d 61 6e 69 70 75 6c 61 72 20 61 73 20 64 |ozManipular as d| 00000060 65 66 69 6e 69 c3 a7 c3 b5 65 73 20 71 75 65 20 |efini....es que | 00000070 63 6f 6e 74 72 6f 6c 61 6d 20 6f 20 61 63 65 73 |controlam o aces| 00000080 73 6f 20 64 65 20 57 65 62 73 69 74 65 73 20 61 |so de Websites a| 00000090 20 63 6f 6f 6b 69 65 73 2c 20 4a 61 76 61 53 63 | cookies, JavaSc| 000000a0 72 69 70 74 20 65 20 70 6c 75 67 2d 69 6e 73 4d |ript e plug-insM| 000000b0 61 6e 69 70 75 6c 61 72 20 61 73 20 64 65 66 69 |anipular as defi| 000000c0 6e 69 c3 a7 c3 b5 65 73 20 72 65 6c 61 63 69 6f |ni....es relacio| 000000d0 6e 61 64 61 73 20 63 6f 6d 20 70 72 69 76 61 63 |nadas com privac| 000000e0 69 64 61 64 65 41 63 65 64 65 72 20 61 6f 73 20 |idadeAceder aos | 000000f0 73 65 75 73 20 70 65 72 69 66 c3 a9 72 69 63 6f |seus perif..rico| 00000100 73 20 55 53 42 55 74 69 6c 69 7a 61 72 20 6f 20 |s USBUtilizar o | 00000110 73 65 75 20 6d 69 63 72 6f 66 6f 6e 65 55 74 69 |seu microfoneUti| 00000120 6c 69 7a 61 72 20 61 20 73 75 61 20 63 c3 a2 6d |lizar a sua c..m| 00000130 61 72 61 55 74 69 6c 69 7a 61 72 20 6f 20 73 65 |araUtilizar o se| 00000140 75 20 6d 69 63 72 6f 66 6f 6e 65 20 65 20 61 20 |u microfone e a | 00000150 63 c3 a2 6d 61 72 61 4e c3 a3 6f 20 66 6f 69 20 |c..maraN..o foi | 00000160 70 6f 73 73 c3 ad 76 65 6c 20 65 6e 63 6f 6e 74 |poss..vel encont| 00000170 72 61 72 20 6f 20 63 61 6d 69 6e 68 6f 20 61 62 |rar o caminho ab| 00000180 73 6f 6c 75 74 6f 20 70 61 72 61 20 6f 20 64 69 |soluto para o di| 00000190 72 65 63 74 c3 b3 72 69 6f 20 61 20 65 6d 70 61 |rect..rio a empa| 000001a0 63 6f 74 61 72 2e 4f 20 64 69 72 65 63 74 c3 b3 |cotar.O direct..| 000001b0 72 69 6f 20 64 65 20 65 6e 74 72 61 64 61 00 fe |rio de entrada..| 000001c0 ff ff 83 fe ff ff 02 00 00 00 00 10 7a 04 00 00 |............z...| 000001d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 000001f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.| 00000200 =============================== StdErr Messages: =============================== xz: (stdin): Compressed data is corrupt xz: (stdin): Compressed data is corrupt awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in Begging / Appreciation ;) If anything else is required to solve my problem, please ask. My only hopes are that I can solve this, and that doing so won't require re-installation of Grub due to how complicated the procedures are, or that I would be needed to reinstall the OS', as I have done so about six times already since friday due to several other issues I've encountered. Thank you, and good day. System Ubuntu 12.04 64-bit / Windows 7 SP1 64-bit 64GB SSD as boot/OS drive, 1TB HDD as /Home Swap and Steam drive.

    Read the article

  • OBIEE 11.1.1 - OBIEE 11g Full Sample App on VMware Player 4

    - by user809526
    The Full Sample App is designed to run on Virtual Box. Let's describe how to run it on VMware Player 4. Open Virtualization Format Tool http://communities.vmware.com/community/vmtn/server/vsphere/automationtools/ovf VMware Player Documentation https://www.vmware.com/support/pubs/player_pubs.html Full Sample App Deployment Guide sampleapp107-vbimage-deployguide-453583.pdf INSTALL VMplayer 4.0.0 as root LINUX # sh VMware-Player-4.0.0-471780.x86_64.bundle (A new VM is not needed and can be deleted later after that installation is completed. "I will install OS later" - blank hard disk Guest: linux, Red Hat Enterprise Linux 5-64bits => rename to RHEL target: eg /a/root/vmware/ Max disk size: 5 GB (will be deleted) Disk: Single file Dummy RHEL.vmk, RHEL.vmdk is generated. "Delete VM from Disk" in VM Player.) Copy Full Sample App files to target /a/root/vmware/ WARNING: Select a target eg /a/root/vmware/ with lots of free space, 95 GB. Check checksums (md5sum). Please do it! ff85c7eacf7fb8c382e98da875e879e1  Sampleapp_v107_GA-disk1.vmdk 973258cb3c7d64ab03ae853278cf2233  Sampleapp_v107_GA-disk2.vmdk e576be16e36d810479736bfb15d050f5  Sampleapp_v107_GA-disk3.vmdk 3455df77279e53e07d5fee6712f1597d  Sampleapp_v107_GA-disk4.vmdk OVF FILE   Sampleapp_v107_GA.ovf CONVERSION $ cd /a/root/vmware/ LINUX $ /usr/bin/ovftool -tt=ovf --compress=1 -dm=monolithicSparse Sampleapp_v107_GA.ovf .  [dot] Opening OVF source: Sampleapp_v107_GA.ovf Warning: No manifest file Opening OVF target: . Writing OVF package: Sampleapp_v107_GA/Sampleapp_v107_GA.ovf Disk Transfer Completed                   Completed successfully WINDOWS CYGWIN $ /cygdrive/c/VMwarePlayer/OVFTool/ovftool.exe -tt=ovf --compress=1 -dm=monolithicSparse Sampleapp_v107_GA.ovf .  [dot] Opening OVF source: Sampleapp_v107_GA.ovf Warning: No manifest file Opening OVF target: . Writing OVF package: Sampleapp_v107_GA\Sampleapp_v107_GA.ovf Disk Transfer Completed Completed successfully /a/root/vmware$ du -sk 49095328    .   [50 GB already occupied] IMPORT - First start of VM Player 4: /usr/bin/vmplayer "Open a Virtual Machine" Browse to /a/root/vmware/Sampleapp_v107_GA/Sampleapp_v107_GA.ovf [the new generated .ovf] "Import Virtual Machine" dialog Name: Sampleapp_v107_GA Location: /a/root/vmware/Sampleapp_v107_GA/storage [was /home/tdubois/vmware/Sampleapp_v107_GA] "Import" "The import failed because /a/root/vmware/Sampleapp_v107_GA/Sampleapp_v107_GA.ovf did not pass OVF specification conformance or virtual hardware compliance checks. Click Retry to relax OVF specification..." "Retry" ; Long import /a/root/vmware/Sampleapp_v107_GA/storage/Sampleapp_v107_GA.vmx and new .vmdk files are created. /a/root/vmware$ du -sk 95551384    .   [95 GB occupied] Full Sample App GUEST SETUP "Edit VM settings" min 3GB, 2+ processors, network bridged. For OBIEE + Essbase testing use 8 GB RAM hardware. At first time lauch of Full Sample App, leave OEL booting for several minutes undisturbed. Problem with X display server may occur [/usr/bin/Xorg ; man Xorg]. "Failed to start the X server.... Would you like to view the X server output to diagnose the problem?" "No" [tab key] "Would you like to try to configure the X server? Note that you will need the root password for this." "Yes" [oracle] X Display Settings 800x600 saved in /etc/X11/xorg.conf "Trying to restart the X server" Login as root/oracle in guest OEL. In guest OEL, Virtual Machine > Install VMware Tools... Extract archive VMwareTools-8.8.0-471268.tar.gz all files in writable local directory eg /root In Terminal run Perl script # cd /root/vmware-tools-distrib ; ./vmware-install.pl [keep all default answers] Set keyboard layout System > Preferences > Keyboard > Layouts Restart X server eg System > Log Out root... , relogin Modify X resolution System > Preferences > Screen Resolution Full Sample App OEL login: oracle/oracle ; root/oracle [default US keyboard layout] Credentials are described in the 'sampleapp107-vbimage-deployguide-453583.pdf' The large files in /a/root/vmware/ /a/root/vmware/Sampleapp_v107_GA/ may be removed. FAILURE REMARK: Adding the 4 original Sampleapp_v107_GA-disks[1234].vmdk to VM Player does NOT work as described below. "Edit VM settings" "Remove" "Hard Disk" "Edit VM settings" "Add" "Hard Disk" "Next" "Use an existing virtual disk" "Browse" "Finish" "Keep existing format" "Ok" for each 4 disks settings one by one. Start VM Player 4. "You do not have write access to a partition" Allow all Sampleapp_v107 OEL linux launches. OEL stalls silently after 'Checking filesystems'.

    Read the article

  • Sun Fire X4800 M2 Delivers World Record TPC-C for x86 Systems

    - by Brian
    Oracle's Sun Fire X4800 M2 server equipped with eight 2.4 GHz Intel Xeon Processor E7-8870 chips obtained a result of 5,055,888 tpmC on the TPC-C benchmark. This result is a world record for x86 servers. Oracle demonstrated this world record database performance running Oracle Database 11g Release 2 Enterprise Edition with Partitioning. The Sun Fire X4800 M2 server delivered a new x86 TPC-C world record of 5,055,888 tpmC with a price performance of $0.89/tpmC using Oracle Database 11g Release 2. This configuration is available 06/26/12. The Sun Fire X4800 M2 server delivers 3.0x times better performance than the next 8-processor result, an IBM System p 570 equipped with POWER6 processors. The Sun Fire X4800 M2 server has 3.1x times better price/performance than the 8-processor 4.7GHz POWER6 IBM System p 570. The Sun Fire X4800 M2 server has 1.6x times better performance than the 4-processor IBM x3850 X5 system equipped with Intel Xeon processors. This is the first TPC-C result on any system using eight Intel Xeon Processor E7-8800 Series chips. The Sun Fire X4800 M2 server is the first x86 system to get over 5 million tpmC. The Oracle solution utilized Oracle Linux operating system and Oracle Database 11g Enterprise Edition Release 2 with Partitioning to produce the x86 world record TPC-C benchmark performance. Performance Landscape Select TPC-C results (sorted by tpmC, bigger is better) System p/c/t tpmC Price/tpmC Avail Database MemorySize Sun Fire X4800 M2 8/80/160 5,055,888 0.89 USD 6/26/2012 Oracle 11g R2 4 TB IBM x3850 X5 4/40/80 3,014,684 0.59 USD 7/11/2011 DB2 ESE 9.7 3 TB IBM x3850 X5 4/32/64 2,308,099 0.60 USD 5/20/2011 DB2 ESE 9.7 1.5 TB IBM System p 570 8/16/32 1,616,162 3.54 USD 11/21/2007 DB2 9.0 2 TB p/c/t - processors, cores, threads Avail - availability date Oracle and IBM TPC-C Response times System tpmC Response Time (sec) New Order 90th% Response Time (sec) New Order Average Sun Fire X4800 M2 5,055,888 0.210 0.166 IBM x3850 X5 3,014,684 0.500 0.272 Ratios - Oracle Better 1.6x 1.4x 1.3x Oracle uses average new order response time for comparison between Oracle and IBM. Graphs of Oracle's and IBM's response times for New-Order can be found in the full disclosure reports on TPC's website TPC-C Official Result Page. Configuration Summary and Results Hardware Configuration: Server Sun Fire X4800 M2 server 8 x 2.4 GHz Intel Xeon Processor E7-8870 4 TB memory 8 x 300 GB 10K RPM SAS internal disks 8 x Dual port 8 Gbs FC HBA Data Storage 10 x Sun Fire X4270 M2 servers configured as COMSTAR heads, each with 1 x 3.06 GHz Intel Xeon X5675 processor 8 GB memory 10 x 2 TB 7.2K RPM 3.5" SAS disks 2 x Sun Storage F5100 Flash Array storage (1.92 TB each) 1 x Brocade 5300 switches Redo Storage 2 x Sun Fire X4270 M2 servers configured as COMSTAR heads, each with 1 x 3.06 GHz Intel Xeon X5675 processor 8 GB memory 11 x 2 TB 7.2K RPM 3.5" SAS disks Clients 8 x Sun Fire X4170 M2 servers, each with 2 x 3.06 GHz Intel Xeon X5675 processors 48 GB memory 2 x 300 GB 10K RPM SAS disks Software Configuration: Oracle Linux (Sun Fire 4800 M2) Oracle Solaris 11 Express (COMSTAR for Sun Fire X4270 M2) Oracle Solaris 10 9/10 (Sun Fire X4170 M2) Oracle Database 11g Release 2 Enterprise Edition with Partitioning Oracle iPlanet Web Server 7.0 U5 Tuxedo CFS-R Tier 1 Results: System: Sun Fire X4800 M2 tpmC: 5,055,888 Price/tpmC: 0.89 USD Available: 6/26/2012 Database: Oracle Database 11g Cluster: no New Order Average Response: 0.166 seconds Benchmark Description TPC-C is an OLTP system benchmark. It simulates a complete environment where a population of terminal operators executes transactions against a database. The benchmark is centered around the principal activities (transactions) of an order-entry environment. These transactions include entering and delivering orders, recording payments, checking the status of orders, and monitoring the level of stock at the warehouses. Key Points and Best Practices Oracle Database 11g Release 2 Enterprise Edition with Partitioning scales easily to this high level of performance. COMSTAR (Common Multiprotocol SCSI Target) is the software framework that enables an Oracle Solaris host to serve as a SCSI Target platform. COMSTAR uses a modular approach to break the huge task of handling all the different pieces in a SCSI target subsystem into independent functional modules which are glued together by the SCSI Target Mode Framework (STMF). The modules implementing functionality at SCSI level (disk, tape, medium changer etc.) are not required to know about the underlying transport. And the modules implementing the transport protocol (FC, iSCSI, etc.) are not aware of the SCSI-level functionality of the packets they are transporting. The framework hides the details of allocation providing execution context and cleanup of SCSI commands and associated resources and simplifies the task of writing the SCSI or transport modules. Oracle iPlanet Web Server middleware is used for the client tier of the benchmark. Each web server instance supports more than a quarter-million users while satisfying the response time requirement from the TPC-C benchmark. See Also Oracle Press Release -- Sun Fire X4800 M2 TPC-C Executive Summary tpc.org Complete Sun Fire X4800 M2 TPC-C Full Disclosure Report tpc.org Transaction Processing Performance Council (TPC) Home Page Ideas International Benchmark Page Sun Fire X4800 M2 Server oracle.com OTN Oracle Linux oracle.com OTN Oracle Solaris oracle.com OTN Oracle Database 11g Release 2 Enterprise Edition oracle.com OTN Sun Storage F5100 Flash Array oracle.com OTN Disclosure Statement TPC Benchmark C, tpmC, and TPC-C are trademarks of the Transaction Processing Performance Council (TPC). Sun Fire X4800 M2 (8/80/160) with Oracle Database 11g Release 2 Enterprise Edition with Partitioning, 5,055,888 tpmC, $0.89 USD/tpmC, available 6/26/2012. IBM x3850 X5 (4/40/80) with DB2 ESE 9.7, 3,014,684 tpmC, $0.59 USD/tpmC, available 7/11/2011. IBM x3850 X5 (4/32/64) with DB2 ESE 9.7, 2,308,099 tpmC, $0.60 USD/tpmC, available 5/20/2011. IBM System p 570 (8/16/32) with DB2 9.0, 1,616,162 tpmC, $3.54 USD/tpmC, available 11/21/2007. Source: http://www.tpc.org/tpcc, results as of 7/15/2011.

    Read the article

  • Updating the value of a math equation with YUI slider and simple radio buttons.

    - by dj lewis
    I have a form that is used to show a price for a product. I have a YUI slider setup that changes the price, and it works perfectly. Now I'm trying to add in radio buttons that also should update that same price value. The price displayed should take into account all 3 fields, and update dynamically as any are updated. This is the code I have, but I don't have any radio buttons for cpanelPrice yet as I'm still just trying to get the IPs to work. <script type="text/javascript"> (function() { var Event = YAHOO.util.Event, Dom = YAHOO.util.Dom, lang = YAHOO.lang, slider, bg="slider-bg", thumb="slider-thumb", orderlink="order-link", monthlyprice="monthly-price", dram="ram", stor="storage",dcpu="cpu",bandw="bandwidth",slid="sliderbg" // The slider can move 0 pixels up var topConstraint = 0; // The slider can move 200 pixels down var bottomConstraint = 585; // Custom scale factor for converting the pixel offset into a real value var scaleFactor = 1; // The amount the slider moves when the value is changed with the arrow // keys var keyIncrement = 65; var tickSize = 65; Event.onDOMReady(function() { slider = YAHOO.widget.Slider.getHorizSlider(bg, thumb, topConstraint, bottomConstraint, tickSize); slider.setValue(1, true); slider.animate = true; slider.getRealValue = function() { return Math.round(this.getValue() * scaleFactor); } slider.subscribe("change", function(offsetFromStart) { var ordnode = Dom.get(orderlink); var prinode = Dom.get(monthlyprice); var ramnode = Dom.get(dram); var stornode = Dom.get(stor); var cpunode = Dom.get(dcpu); var bwnode = Dom.get(bandw); var slidnode = Dom.get(slid); var actualValue = slider.getRealValue(); if (actualValue < 0) { var actualValue = 0; } if (actualValue > -1 && actualValue < 5) { basePrice = 15; var pid = "7"; var ram = "128 MB"; stornode.innerHTML = "5"; cpunode.innerHTML = ".5"; bwnode.innerHTML = "50"; slidnode.innerHTML = "<img src=\"/images/sliderbg1.png\" alt=\"\" />"; } else if (actualValue > 60 && actualValue < 70) { basePrice = 25; var pid = "8"; var ram = "256 MB"; stornode.innerHTML = "10"; cpunode.innerHTML = ".5"; bwnode.innerHTML = "100"; slidnode.innerHTML = "<img src=\"/images/sliderbg2.png\" alt=\"\" />"; } else if (actualValue > 125 && actualValue < 135) { basePrice = 40; var pid = "9"; var ram = "512 MB"; stornode.innerHTML = "20"; cpunode.innerHTML = "1"; bwnode.innerHTML = "200"; slidnode.innerHTML = "<img src=\"/images/sliderbg3.png\" alt=\"\" />"; } else if (actualValue > 190 && actualValue < 200) { basePrice = 60; var pid = "10"; var ram = "1 GB"; stornode.innerHTML = "40"; cpunode.innerHTML = "1"; bwnode.innerHTML = "400"; slidnode.innerHTML = "<img src=\"/images/sliderbg4.png\" alt=\"\" />"; } else if (actualValue> 255 && actualValue < 265) { basePrice = 80; var pid = "11"; var ram = "1.5 GB"; stornode.innerHTML = "60"; cpunode.innerHTML = "1"; bwnode.innerHTML = "600"; slidnode.innerHTML = "<img src=\"/images/sliderbg5.png\" alt=\"\" />"; } else if (actualValue > 320 && actualValue < 330) { basePrice = 110; var pid = "12"; var ram = "2 GB"; stornode.innerHTML = "80"; cpunode.innerHTML = "2"; bwnode.innerHTML = "800"; slidnode.innerHTML = "<img src=\"/images/sliderbg6.png\" alt=\"\" />"; } else if (actualValue > 385 && actualValue < 395) { basePrice = 140; var pid = "13"; var ram = "2.5 GB"; stornode.innerHTML = "100"; cpunode.innerHTML = "2"; bwnode.innerHTML = "1000"; slidnode.innerHTML = "<img src=\"/images/sliderbg7.png\" alt=\"\" />"; } else if (actualValue > 450 && actualValue < 460) { basePrice = 170; var pid = "14"; var ram = "3 GB"; stornode.innerHTML = "120"; cpunode.innerHTML = "3"; bwnode.innerHTML = "1200"; slidnode.innerHTML = "<img src=\"/images/sliderbg8.png\" alt=\"\" />"; } else if (actualValue > 515 && actualValue < 525) { basePrice = 200; var pid = "15"; var ram = "3.5 GB"; stornode.innerHTML = "140"; cpunode.innerHTML = "3"; bwnode.innerHTML = "1400"; slidnode.innerHTML = "<img src=\"/images/sliderbg9.png\" alt=\"\" />"; } else if (actualValue > 580 && actualValue < 590) { basePrice = 240; var pid = "16"; var ram = "4 GB"; stornode.innerHTML = "160"; cpunode.innerHTML = "4"; bwnode.innerHTML = "1600"; slidnode.innerHTML = "<img src=\"/images/sliderbg10.png\" alt=\"\" />"; } // Setup the order link ordnode.innerHTML = "<a href=\"https://account.hostingbeast.com/cart.php?a=add&pid=" + pid + "\"><img src=\"/images/blank.gif\" alt=\"Order VPS Hosting\" height=\"100\" width=\"100\" /></a>"; ramnode.innerHTML = ram; ipPrice = 0; function setIpPrice(ips) { ipPrice = ips.value; } cpanelPrice = 0; prinode.innerHTML = basePrice + ipPrice + cpanelPrice; }); // Use setValue to reset the value to white: Event.on("putval", "click", function(e) { slider.setValue(100, false); //false here means to animate if possible }); setTimeout(function () { slider.setValue(10); },0); }); })(); </script> <div style="width: 649px; margin:auto"> <span id="sliderbg"></span> <div class="yui-skin-sam"> <div id="slider-bg" class="yui-h-slider" tabindex="-1"> <div id="slider-thumb" class="yui-slider-thumb"><img src="/images/thumb-bar.png"></div> </div> </div> </div> <div class="vpsdetails"> <div id="vpsprod"><span id="cpu"></span></div> <div id="vpsram"><span id="ram"></span></div> <div id="vpsstor"><span id="storage"></span> GB</div> <div id="vpsbw"><span id="bandwidth"></span> GB</div> <div id="slideprice">$ <span id="monthly-price"></span></div> </div> <input type="radio" name="ips" value="2" onclick="setIpPrice(this.value - 2 * 2);" checked="checked" /> 2 <input type="radio" name="ips" value="4" onclick="setIpPrice(this.value - 2 * 2);" /> 4

    Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >