Search Results

Search found 788 results on 32 pages for 'gert 78'.

Page 18/32 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

• Linux router: ping doesn't route back

  - by El Barto

  I have a Debian box which I'm trying to set up as a router and an Ubuntu box which I'm using as a client. My problem is that when the Ubuntu client tries to ping a server on the Internet, all the packets are lost (though, as you can see below, they seem to go to the server and back without problem). I'm doing this in the Ubuntu Box: # ping -I eth1 my.remote-server.com PING my.remote-server.com (X.X.X.X) from 10.1.1.12 eth1: 56(84) bytes of data. ^C --- my.remote-server.com ping statistics --- 13 packets transmitted, 0 received, 100% packet loss, time 12094ms (I changed the name and IP of the remote server for privacy). From the Debian Router I see this: # tcpdump -i eth1 -qtln icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 7, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 305, seq 8, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 8, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 305, seq 9, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 9, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 305, seq 10, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 10, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 305, seq 11, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 11, length 64 ^C 9 packets captured 9 packets received by filter 0 packets dropped by kernel # tcpdump -i eth2 -qtln icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth2, link-type EN10MB (Ethernet), capture size 65535 bytes IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 213, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 213, length 64 IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 214, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 214, length 64 IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 215, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 215, length 64 IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 216, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 216, length 64 IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 217, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 217, length 64 ^C 10 packets captured 10 packets received by filter 0 packets dropped by kernel And at the remote server I see this: # tcpdump -i eth0 -qtln icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 96 bytes IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 1, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 1, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 2, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 2, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 3, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 3, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 4, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 4, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 5, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 5, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 6, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 6, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 7, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 7, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 8, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 8, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 9, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 9, length 64 18 packets captured 228 packets received by filter 92 packets dropped by kernel Here "X.X.X.X" is my remote server's IP and "Y.Y.Y.Y" is my local network's public IP. So, what I understand is that the ping packets are coming out of the Ubuntu box (10.1.1.12), to the router (10.1.1.1), from there to the next router (192.168.1.1) and reaching the remote server (X.X.X.X). Then they come back all the way to the Debian router, but they never reach the Ubuntu box back. What am I missing? Here's the Debian router setup: # ifconfig eth1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:d98/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:105761 errors:0 dropped:0 overruns:0 frame:0 TX packets:48944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:40298768 (38.4 MiB) TX bytes:44831595 (42.7 MiB) Interrupt:19 Base address:0x6000 eth2 Link encap:Ethernet HWaddr 6c:f0:49:a4:47:38 inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fea4:4738/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38335992 errors:0 dropped:0 overruns:0 frame:0 TX packets:37097705 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:4260680226 (3.9 GiB) TX bytes:3759806551 (3.5 GiB) Interrupt:27 eth3 Link encap:Ethernet HWaddr 94:0c:6d:82:c8:72 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:20 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3408 errors:0 dropped:0 overruns:0 frame:0 TX packets:3408 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:358445 (350.0 KiB) TX bytes:358445 (350.0 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:2767779 errors:0 dropped:0 overruns:0 frame:0 TX packets:1569477 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3609469393 (3.3 GiB) TX bytes:96113978 (91.6 MiB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth2 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth2 # arp -n # Note: Here I have changed all the different MACs except the ones corresponding to the Ubuntu box (on 10.1.1.12 and 192.168.1.12) Address HWtype HWaddress Flags Mask Iface 192.168.1.118 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.72 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.94 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.102 ether NN:NN:NN:NN:NN:NN C eth2 10.1.1.12 ether 00:1e:67:15:2b:f0 C eth1 192.168.1.86 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.2 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.61 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.64 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.116 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.91 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.52 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.93 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.87 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.92 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.100 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.40 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.53 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.1 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.83 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.89 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.12 ether 00:1e:67:15:2b:f1 C eth2 192.168.1.77 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.66 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.90 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.65 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.41 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.78 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.123 ether NN:NN:NN:NN:NN:NN C eth2 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- 10.1.1.0/24 !10.1.1.0/24 MASQUERADE all -- !10.1.1.0/24 10.1.1.0/24 Chain OUTPUT (policy ACCEPT) target prot opt source destination And here's the Ubuntu box: # ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:67:15:2b:f1 inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe15:2bf1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28785139 errors:0 dropped:0 overruns:0 frame:0 TX packets:19050735 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:32068182803 (32.0 GB) TX bytes:6061333280 (6.0 GB) Interrupt:16 Memory:b1a00000-b1a20000 eth1 Link encap:Ethernet HWaddr 00:1e:67:15:2b:f0 inet addr:10.1.1.12 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe15:2bf0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:285086 errors:0 dropped:0 overruns:0 frame:0 TX packets:12719 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30817249 (30.8 MB) TX bytes:2153228 (2.1 MB) Interrupt:16 Memory:b1900000-b1920000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:86048 errors:0 dropped:0 overruns:0 frame:0 TX packets:86048 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11426538 (11.4 MB) TX bytes:11426538 (11.4 MB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.1.1 0.0.0.0 UG 100 0 0 eth1 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.8.0.0 192.168.1.10 255.255.255.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 # arp -n # Note: Here I have changed all the different MACs except the ones corresponding to the Debian box (on 10.1.1.1 and 192.168.1.10) Address HWtype HWaddress Flags Mask Iface 192.168.1.70 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.90 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.97 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.103 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.13 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.120 (incomplete) eth0 192.168.1.111 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.118 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.51 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.102 (incomplete) eth0 192.168.1.64 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.52 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.74 (incomplete) eth0 192.168.1.94 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.121 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.72 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.87 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.91 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.71 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.78 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.83 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.88 (incomplete) eth0 192.168.1.82 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.98 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.100 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.93 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.73 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.11 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.85 (incomplete) eth0 192.168.1.112 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.89 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.65 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.81 ether NN:NN:NN:NN:NN:NN C eth0 10.1.1.1 ether 94:0c:6d:82:0d:98 C eth1 192.168.1.53 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.116 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.61 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.10 ether 6c:f0:49:a4:47:38 C eth0 192.168.1.86 (incomplete) eth0 192.168.1.119 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.66 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.1 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.1 ether NN:NN:NN:NN:NN:NN C eth1 192.168.1.92 ether NN:NN:NN:NN:NN:NN C eth0 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination Edit: Following Patrick's suggestion, I did a tcpdump con the Ubuntu box and I see this: # tcpdump -i eth1 -qtln icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 1, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 1, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 2, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 2, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 3, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 3, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 4, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 4, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 5, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 5, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 6, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 6, length 64 ^C 12 packets captured 12 packets received by filter 0 packets dropped by kernel So the question is: if all packets seem to be coming and going, why does ping report 100% packet loss?

  Read the article

• Regular Expressions Cookbook Is in The Money—Win a Copy

  - by Jan Goyvaerts

  %COOKBOOKFRAME%You may have heard some people say that most book authors never get any royalties. That’s not true because most authors get an advance royalty that is paid before the book is published. That’s the author’s main incentive for writing the book, at least as far as money is concerned. (If money is your main concern, don’t write books.) What is true is that most authors never see any money beyond the advance royalty. Royalty rates are very low. A 10% royalty of the publisher’s price is considered normal. The publisher’s price is usually 45% of the retail price. So if you pay full price in a bookstore, the author gets 4.5% of your money. If there’s more than one author, they split the royalty. It doesn’t take a math degree to figure out that a book needs to sell quite a few copies for the royalty to add up to a meaningful amount of money. But Steven and I must have done something right. Regular Expressions Cookbook is in the money. My royalty statement for the 3rd quartier of 2009, which is the 2nd quarter that the book was on the market, came with a check. I actually received it last month but didn’t get around to blogging about. The amount of the check is insignificant. The point is that the balance is no longer negative. I’m taking this opportunity to pat myself and my co-author on the back. To celebrate the occassion O’Reilly has offered to sponsor a give-away of five (5) copies of Regular Expressions Cookbook. These are the rules of the game: You must post a comment to this blog article including your actual name and actual email address. Names are published, email addresses are not. Comments are moderated by myself (Jan Goyvaerts). If I consider a comment to be offensive or spam it will not be published and not be eligible for any prize. If you don’t know what to say in the comment, just wish me a happy 100000nd birthday, so I don’t have to feel so bad about entering the 6-bit era. Each person commenting has only one chance to win, regardless of the number of comments posted. O’Reilly will be provided with the names and email addresses of the winners (and those email addresses only) in order to arrange delivery. Each winner can choose to receive a printed copy or ebook (DRM-free PDF). If you choose the printed book, O’Reilly pays for shipping to anywhere in the world but not for any duties or taxes your country may impose on books imported from the USA. If you choose the ebook, you’ll need to create an O’Reilly account that is then granted access to the PDF download. You can make your choice after you’ve won, so it doesn’t influence your chance of winning. Contest ends 28 February 2010, GMT+7 (Thai time). Chosen by five calls to Random(78)+1 in Delphi 2010, the winners are: 48: Xiaozu 45: David Chisholm 19: Miquel Burns 33: Aaron Rice 17: David Laing Thanks to everybody who participated. The winners have been notified by email on how to collect their prize.

  Read the article

• Slow wifi on Ubuntu 12.04 wifi driver ath9k

  - by lunar

  For the last couple of days my wifi connection is extremely slow. I am pretty sure that it is caused by the driver. Can this be improved? lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"MyWiFi" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:68:FE:7B:C7 Bit Rate=58.5 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:6960 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: 74:f0:6d:34:c2:4e width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d7400000-d740ffff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:4b:38:78:f6:ae capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128) lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 04f2:b1bb Chicony Electronics Co., Ltd Bus 001 Device 004: ID 0b05:1788 ASUSTek Computer, Inc. lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 06) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [GeForce GT 425M] (rev a1) 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 04:00.0 USB controller: Fresco Logic Device 1400 (rev 01) 06:00.0 Ethernet controller: Atheros Communications Inc. AR8131 Gigabit Ethernet (rev c0) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) rfkill list all 0: hci0: Bluetooth Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• Mirroring git and mercurial repos the lazy way

  - by Greg Malcolm

  I maintain Python Koans on mirrored on both Github using git and Bitbucket using mercurial. I get pull requests from both repos but it turns out keeping the two repos in sync is pretty easy. Here is how it's done... Assuming I’m starting again on a clean laptop, first I clone both repos ~/git $ hg clone https://bitbucket.org/gregmalcolm/python_koans ~/git $ git clone [email protected]:gregmalcolm/python_koans.git python_koans2 The only thing that makes a folder a git or mercurial repository is the .hg folder in the root of python_koans and the .git folder in the root of python_koans2. So I just need to move the .git folder over into the python_koans folder I'm using for mercurial: ~/git $ rm -rf python_koans/.git ~/git $ mv python_koans2/.git python_koans ~/git $ ls -la python_koans total 48 drwxr-xr-x 11 greg staff 374 Mar 17 15:10 . drwxr-xr-x 62 greg staff 2108 Mar 17 14:58 .. drwxr-xr-x 12 greg staff 408 Mar 17 14:58 .git -rw-r--r-- 1 greg staff 34 Mar 17 14:54 .gitignore drwxr-xr-x 13 greg staff 442 Mar 17 14:54 .hg -rw-r--r-- 1 greg staff 48 Mar 17 14:54 .hgignore -rw-r--r-- 1 greg staff 365 Mar 17 14:54 Contributor Notes.txt -rw-r--r-- 1 greg staff 1082 Mar 17 14:54 MIT-LICENSE -rw-r--r-- 1 greg staff 5765 Mar 17 14:54 README.txt drwxr-xr-x 10 greg staff 340 Mar 17 14:54 python 2 drwxr-xr-x 10 greg staff 340 Mar 17 14:54 python 3 That’s about it! Now git and mercurial are tracking files in the same folder. Of course you will still need to set up your .gitignore to ignore mercurial’s dotfiles and .hgignore to ignore git’s dotfiles or there will be squabbling in the backseat. ~/git $ cd python_koans/ ~/git/python_koans $ cat .gitignore *.pyc *.swp .DS_Store answers .hg <-- Ignore mercurial ~/git/python_koans $ cat .hgignore syntax: glob *.pyc *.swp .DS_Store answers .git <-- Ignore git Because both my mirrors are both identical as far as tracked files are concerned I won’t yet see anything if I check statuses at this point: ~/git/python_koans $ git status # On branch master nothing to commit (working directory clean) ~/git/python_koans $ hg status ~/git/python_koans But how about if I accept a pull request from the bitbucket (mercuial) site? ~/git/python_koans $ hg status ~/git/python_koans $ git status # On branch master # Your branch is behind 'origin/master' by 1 commit, and can be fast-forwarded. # # Changed but not updated: # (use "git add <file>..." to update what will be committed) # (use "git checkout -- <file>..." to discard changes in working directory) # # modified: python 2/koans/about_decorating_with_classes.py # modified: python 2/koans/about_iteration.py # modified: python 2/koans/about_with_statements.py # modified: python 3/koans/about_decorating_with_classes.py # modified: python 3/koans/about_iteration.py # modified: python 3/koans/about_with_statements.py Mercurial doesn’t have any changes to track right now, but git has changes. Commit and push them up to github and balance is restored to the force: ~/git/python_koans $ git commit -am "Merge from bitbucket mirror: 'gpiancastelli - Fix for issue #21 and some other tweaks'" [master 79ca184] Merge from bitbucket mirror: 'gpiancastelli - Fix for issue #21 and some other tweaks' 6 files changed, 78 insertions(+), 63 deletions(-) ~/git/python_koans $ git push origin master Or just use hg-git? The github developers have actually published a plugin for automatic mirroring: http://hg-git.github.com I haven’t used it because at the time I tried it a couple of years ago I was having problems getting all the parts to play nice with each other. Probably works fine now though..

  Read the article

• Problem with AssetManager while loading a Model type

  - by user1204548

  Today I've tried the AssetManager for the first time with .g3db files and I'm having some problems. Exception in thread "LWJGL Application" com.badlogic.gdx.utils.GdxRuntimeException: com.badlogic.gdx.utils.GdxRuntimeException: Couldn't load dependencies of asset: data/data at com.badlogic.gdx.assets.AssetManager.handleTaskError(AssetManager.java:508) at com.badlogic.gdx.assets.AssetManager.update(AssetManager.java:342) at com.lostchg.martagdx3d.MartaGame.render(MartaGame.java:78) at com.badlogic.gdx.Game.render(Game.java:46) at com.badlogic.gdx.backends.lwjgl.LwjglApplication.mainLoop(LwjglApplication.java:207) at com.badlogic.gdx.backends.lwjgl.LwjglApplication$1.run(LwjglApplication.java:114) Caused by: com.badlogic.gdx.utils.GdxRuntimeException: Couldn't load dependencies of asset: data/data at com.badlogic.gdx.assets.AssetLoadingTask.handleAsyncLoader(AssetLoadingTask.java:119) at com.badlogic.gdx.assets.AssetLoadingTask.update(AssetLoadingTask.java:89) at com.badlogic.gdx.assets.AssetManager.updateTask(AssetManager.java:445) at com.badlogic.gdx.assets.AssetManager.update(AssetManager.java:340) ... 4 more Caused by: com.badlogic.gdx.utils.GdxRuntimeException: com.badlogic.gdx.utils.GdxRuntimeException: Couldn't load file: data/data at com.badlogic.gdx.utils.async.AsyncResult.get(AsyncResult.java:31) at com.badlogic.gdx.assets.AssetLoadingTask.handleAsyncLoader(AssetLoadingTask.java:117) ... 7 more Caused by: com.badlogic.gdx.utils.GdxRuntimeException: Couldn't load file: data/data at com.badlogic.gdx.graphics.Pixmap.<init>(Pixmap.java:140) at com.badlogic.gdx.assets.loaders.TextureLoader.loadAsync(TextureLoader.java:72) at com.badlogic.gdx.assets.loaders.TextureLoader.loadAsync(TextureLoader.java:41) at com.badlogic.gdx.assets.AssetLoadingTask.call(AssetLoadingTask.java:69) at com.badlogic.gdx.assets.AssetLoadingTask.call(AssetLoadingTask.java:34) at com.badlogic.gdx.utils.async.AsyncExecutor$2.call(AsyncExecutor.java:49) at java.util.concurrent.FutureTask.run(Unknown Source) at java.util.concurrent.ThreadPoolExecutor.runWorker(Unknown Source) at java.util.concurrent.ThreadPoolExecutor$Worker.run(Unknown Source) at java.lang.Thread.run(Unknown Source) Caused by: com.badlogic.gdx.utils.GdxRuntimeException: File not found: data\data (Internal) at com.badlogic.gdx.files.FileHandle.read(FileHandle.java:132) at com.badlogic.gdx.files.FileHandle.length(FileHandle.java:586) at com.badlogic.gdx.files.FileHandle.readBytes(FileHandle.java:220) at com.badlogic.gdx.graphics.Pixmap.<init>(Pixmap.java:137) ... 9 more Why it tries to load that unexisting file? It seems that the AssetManager manages to load my .g3db file at first, because earlier the java console threw some errors related to the textures associated to the 3D scene having to be a power of 2. Relevant code: public void show() { ... assets = new AssetManager(); assets.load("data/levelprueba2.g3db", Model.class); loading = true; ... } private void doneLoading() { Model model = assets.get("data/levelprueba2.g3db", Model.class); for (int i = 0; i < model.nodes.size; i++) { String id = model.nodes.get(i).id; ModelInstance instance = new ModelInstance(model, id); Node node = instance.getNode(id); instance.transform.set(node.globalTransform); node.translation.set(0,0,0); node.scale.set(1,1,1); node.rotation.idt(); instance.calculateTransforms(); instances.add(instance); } loading = false; } public void render(float delta) { super.render(delta); if (loading && assets.update()) doneLoading(); ... } The error points to the line with the assets.update() method. Please, help! Sorry for my bad English and my amateurish doubts.

  Read the article

• Whether to use UNION or OR in SQL Server Queries

  - by Dinesh Asanka

  Recently I came across with an article on DB2 about using Union instead of OR. So I thought of carrying out a research on SQL Server on what scenarios UNION is optimal in and which scenarios OR would be best. I will analyze this with a few scenarios using samples taken  from the AdventureWorks database Sales.SalesOrderDetail table. Scenario 1: Selecting all columns So we are going to select all columns and you have a non-clustered index on the ProductID column. --Query 1 : OR SELECT * FROM Sales.SalesOrderDetail WHERE ProductID = 714 OR ProductID =709 OR ProductID =998 OR ProductID =875 OR ProductID =976 OR ProductID =874 --Query 2 : UNION SELECT * FROM Sales.SalesOrderDetail WHERE ProductID = 714 UNION SELECT * FROM Sales.SalesOrderDetail WHERE ProductID = 709 UNION SELECT * FROM Sales.SalesOrderDetail WHERE ProductID = 998 UNION SELECT * FROM Sales.SalesOrderDetail WHERE ProductID = 875 UNION SELECT * FROM Sales.SalesOrderDetail WHERE ProductID = 976 UNION SELECT * FROM Sales.SalesOrderDetail WHERE ProductID = 874 So query 1 is using OR and the later is using UNION. Let us analyze the execution plans for these queries. Query 1 Query 2 As expected Query 1 will use Clustered Index Scan but Query 2, uses all sorts of things. In this case, since it is using multiple CPUs you might have CX_PACKET waits as well. Let’s look at the profiler results for these two queries: CPU Reads Duration Row Counts OR 78 1252 389 3854 UNION 250 7495 660 3854 You can see from the above table the UNION query is not performing well as the  OR query though both are retuning same no of rows (3854).These results indicate that, for the above scenario UNION should be used. Scenario 2: Non-Clustered and Clustered Index Columns only --Query 1 : OR SELECT ProductID,SalesOrderID, SalesOrderDetailID FROM Sales.SalesOrderDetail WHERE ProductID = 714 OR ProductID =709 OR ProductID =998 OR ProductID =875 OR ProductID =976 OR ProductID =874 GO --Query 2 : UNION SELECT ProductID,SalesOrderID, SalesOrderDetailID FROM Sales.SalesOrderDetail WHERE ProductID = 714 UNION SELECT ProductID,SalesOrderID, SalesOrderDetailID FROM Sales.SalesOrderDetail WHERE ProductID = 709 UNION SELECT ProductID,SalesOrderID, SalesOrderDetailID FROM Sales.SalesOrderDetail WHERE ProductID = 998 UNION SELECT ProductID,SalesOrderID, SalesOrderDetailID FROM Sales.SalesOrderDetail WHERE ProductID = 875 UNION SELECT ProductID,SalesOrderID, SalesOrderDetailID FROM Sales.SalesOrderDetail WHERE ProductID = 976 UNION SELECT ProductID,SalesOrderID, SalesOrderDetailID FROM Sales.SalesOrderDetail WHERE ProductID = 874 GO So this time, we will be selecting only index columns, which means these queries will avoid a data page lookup. As in the previous case we will analyze the execution plans: Query 1 Query 2 Again, Query 2 is more complex than Query 1. Let us look at the profile analysis: CPU Reads Duration Row Counts OR 0 24 208 3854 UNION 0 38 193 3854 In this analyzis, there is only slight difference between OR and UNION. Scenario 3: Selecting all columns for different fields Up to now, we were using only one column (ProductID) in the where clause.  What if we have two columns for where clauses and let us assume both are covered by non-clustered indexes? --Query 1 : OR SELECT * FROM Sales.SalesOrderDetail WHERE ProductID = 714 OR CarrierTrackingNumber LIKE 'D0B8%' --Query 2 : UNION SELECT * FROM Sales.SalesOrderDetail WHERE ProductID = 714 UNION SELECT * FROM Sales.SalesOrderDetail WHERE CarrierTrackingNumber  LIKE 'D0B8%' Query 1 Query 2: As we can see, the query plan for the second query has improved. Let us see the profiler results. CPU Reads Duration Row Counts OR 47 1278 443 1228 UNION 31 1334 400 1228 So in this case too, there is little difference between OR and UNION. Scenario 4: Selecting Clustered index columns for different fields Now let us go only with clustered indexes: --Query 1 : OR SELECT * FROM Sales.SalesOrderDetail WHERE ProductID = 714 OR CarrierTrackingNumber LIKE 'D0B8%' --Query 2 : UNION SELECT * FROM Sales.SalesOrderDetail WHERE ProductID = 714 UNION SELECT * FROM Sales.SalesOrderDetail WHERE CarrierTrackingNumber  LIKE 'D0B8%' Query 1 Query 2 Now both execution plans are almost identical except is an additional Stream Aggregate is used in the first query. This means UNION has advantage over OR in this scenario. Let us see profiler results for these queries again. CPU Reads Duration Row Counts OR 0 319 366 1228 UNION 0 50 193 1228 Now see the differences, in this scenario UNION has somewhat of an advantage over OR. Conclusion Using UNION or OR depends on the scenario you are faced with. So you need to do your analyzing before selecting the appropriate method. Also, above the four scenarios are not all an exhaustive list of scenarios, I selected those for the broad description purposes only.

  Read the article

• MaxTotalSizeInBytes - Blind spots in Usage file and Web Analytics Reports

  - by Gino Abraham

  Originally posted on: http://geekswithblogs.net/GinoAbraham/archive/2013/10/28/maxtotalsizeinbytes---blind-spots-in-usage-file-and-web-analytics.aspx http://blogs.msdn.com/b/sharepoint_strategery/archive/2012/04/16/usage-file-and-web-analytics-reports-with-blind-spots.aspx In my previous post (Troubleshooting SharePoint 2010 Web Analytics), I referenced a problem that can occur when exceeding the daily partition size for the LoggingDB, which generates the ULS message “[Partition] has exceeded the max bytes”. Below, I wanted to provide some additional info on this particular issue and help identify some options if this occurs. As an aside, this post only applies if you are missing portions of Usage data - think blind spots on intermittent days or user activity regularly sparse for the afternoon/evening. If this fits your scenario - read on. But if Usage logs are outright missing, go check out my Troubleshooting post first.  Background on the problem:The LoggingDB database has a default maximum size of ~6GB. However, SharePoint evenly splits this total size into fixed sized logical partitions – and the number of partitions is defined by the number of days to retain Usage data (by default 14 days). In this case, 14 partitions would be created to account for the 14 days of retention. If the retention were halved to 7 days, the LoggingDBwould be split into 7 corresponding partitions at twice the size. In other words, the partition size is generally defined as [max size for DB] / [number of retention days].Going back to the default scenario, the “max size” for the LoggingDB is 6200000000 bytes (~6GB) and the retention period is 14 days. Using our formula, this would be [~6GB] / [14 days], which equates to 444858368 bytes (~425MB) per partition per day. Again, if the retention were halved to 7 days (which halves the number of partitions), the resulting partition size becomes [~6GB] / [7 days], or ~850MB per partition.From my experience, when the partition size for any given day is exceeded, the usage logging for the remainder of the day is essentially thrown away because SharePoint won’t allow any more to be written to that day’s partition. The only clue that this is occurring (beyond truncated usage data) is an error such as the following that gets reported in the ULS:04/08/2012 09:30:04.78    OWSTIMER.EXE (0x1E24)    0x2C98    SharePoint Foundation    Health    i0m6     High    Table RequestUsage_Partition12 has 444858368 bytes that has exceeded the max bytes 444858368It’s also worth noting that the exact bytes reported (e.g. ‘444858368’ above) may slightly vary among farms. For example, you may instead see 445226812, 439123456, or something else in the ballpark. The exact number itself doesn't matter, but this error message intends to indicates that the reporting usage has exceeded the partition size for the given day.What it means:The error itself is easy to miss, which can lead to substantial gaps in the reporting data (your mileage may vary) if not identified. At this point, I can only advise to periodically check the ULS logs for this message. Down the road, I plan to explore if [Developing a Custom Health Rule] could be leveraged to identify the issue (If you've ever built Custom Health Rules, I'd be interested to hear about your experiences). Overcoming this issue also poses a challenge, with workaround options including:Lower the retentionBecause the partition size is generally defined as [max size] / [number of retention days], the first option is to lower the number of days to retain the data – the lower the retention, the lower the divisor and thus a bigger partition. For example, halving the retention from 14 to 7 days would halve the number of partitions, but double the partition size to ~850MB (e.g. [6200000000 bytes] / [7 days] = ~850GB partitions). Lowering it to 2 days would result in two ~3GB partitions… and so on.Recreate the LoggingDB with an increased sizeThe property MaxTotalSizeInBytes is exposed by OM code for the SPUsageDefinition object and can be updated with the example PowerShell snippet below. However, updating this value has no immediate impact because this size only applies when creating a LoggingDB. Therefore, you must create a newLoggingDB for the Usage Service Application. The gotcha: this effectively deletes all prior Usage databecause the Usage Service Application can only have a single LoggingDB.Here is an example snippet to update the "Page Requests" Usage Definition:$def=Get-SPUsageDefinition -Identity "page requests" $def.MaxTotalSizeInBytes=12400000000 $def.update()Create a new Logging database and attach to the Usage Service Application using the following command: Get-spusageapplication | Set-SPUsageApplication -DatabaseServer <dbServer> -DatabaseName <newDBname> Updated (5/10/2012): Once the new database has been created, you can confirm the setting has truly taken by running the following SQL Query (be sure to replace the database name in the following query with the name provided in the PowerShell above)SELECT * FROM [WSS_UsageApplication].[dbo].[Configuration] WITH (nolock) WHERE ConfigName LIKE 'Max Total Bytes - RequestUsage'

  Read the article

• Why does Ubuntu only detect one USB LAN adapters at a time?

  - by EGO

  I try to connect real switch with my computer for an exam preparation, for this purpose I need more than one LAN cards, and there is only one built in LAN card in my computer. So, to get more LAN cards, I bought 4 USB Ethernet adapters (as I have 4 usb ports in may laptop 2 usb 2.0 ports, 2 usb 3.0 ports). When I plug these adapters in my computer Ubuntu only detects one LAN card from 2.0 usb ports, and one LAN card from 3.0 ports. And sometimes detects only one USB LAN from all the usb ports. Actually the real problem is Ubuntu shows these USB LAN adapters in the "lsusb", but does not list them in "ifconfig". Kontron (Industrial Computer Source / ICS Advent) is my LAN USB ethernet. abc@ubuntu:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hu Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hu Bus 002 Device 012: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 001 Device 003: ID 138a:0018 Validity Sensors, Inc. Bus 001 Device 004: ID 064e:e258 Suyin Corp. Bus 003 Device 011: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 002 Device 013: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 003 Device 012: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 002 Device 005: ID 0a5c:21b4 Broadcom Corp. BCM2070 Bluetooth 2.1 + EDR -- etho is my built in LAN card, while eth1 is the only USB LAN card that ubuntu has detected. abc@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 2c:27:d7:a5:d2:39 inet6 addr: fe80::2e27:d7ff:fea5:d239/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:21056 errors:0 dropped:1 overruns:0 frame:0 TX packets:5669 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1407289 (1.4 MB) TX bytes:372566 (372.5 KB) Interrupt:49 Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:e0:4c:53:44:58 inet6 addr: fe80::2e0:4cff:fe53:4458/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:9230 errors:0 dropped:0 overruns:0 frame:0 TX packets:9230 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:557648 (557.6 KB) TX bytes:557648 (557.6 KB) wlan0 Link encap:Ethernet HWaddr cc:52:af:5e:78:05 inet addr:192.168.1.65 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::ce52:afff:fe5e:7805/64 Scope:LinkU UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:17389 errors:0 dropped:0 overruns:0 frame:0 TX packets:12231 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22452248 (22.4 MB) TX bytes:1502750 (1.5 MB) If I unplug the USB LAN card which Ubuntu has detected, then Ubuntu will detect a USB LAN card from the remaining plugged adapters, and process go on untill I plug all the USB LAN adapters. Looking for some urgent help. Thanks

  Read the article

• Errors when trying to compile the driver for the rtl8192su wireless adapter

  - by Tom Brito

  I have a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g sudo lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 06) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller (rev 01) sudo lsusb Bus 002 Device 003: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 045e:00f9 Microsoft Corp. Wireless Desktop Receiver 3.1 Bus 001 Device 003: ID 0b05:1786 ASUSTek Computer, Inc. Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  This seems to be a fairly chronic problem, as shown by the following questions: How do I fix a "Wireless is disabled by hardware switch" error? Wireless disabled by hardware switch "Wireless disabled by hardware switch" after suspend and other hardware buttons ineffective - how can I solve this? but no good solutions have been found! Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. All My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A ip=155.99.215.79 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. xev shows that no internal event is triggered for my wireless switch (f12), but other function keys also acting as hardware switches work fine. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. I just tried to reload bios defaults (or something) as shown by this video. Didn't work. Edit. I tried the contents of this answer, and it didn't work. Edit. I made a pastebin of dmesg. I couldn't even begin to understand the contents. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• How to remove synaptic without installing all the unwanted packages?

  - by Jay

  I am trying to uninstall synaptic. I prefer using apt-get and other command line tools to manage my packages. So I do not need synaptic and the software manager. I'm trying to remove both of them using apt-get. Its a new box. Recently installed Linux Mint mate 15. After installation, the only thing I did was, sudo apt-get update and sudo apt-get dist-upgrade After that, I did this command for removing synaptic, sudo apt-get remove --purge synaptic But this gives me a very weird output, Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: apturl-kde icoutils kate-data katepart kde-runtime kde-runtime-data kdelibs-bin kdelibs5-data kdelibs5-plugins kdesudo kdoctools kubuntu-debug-installer libattica0.4 libdlrestrictions1 libkactivities-bin libkactivities-models1 libkactivities6 libkatepartinterfaces4 libkcmutils4 libkde3support4 libkdeclarative5 libkdecore5 libkdesu5 libkdeui5 libkdewebkit5 libkdnssd4 libkemoticons4 libkfile4 libkhtml5 libkidletime4 libkio5 libkjsapi4 libkjsembed4 libkmediaplayer4 libknewstuff3-4 libknotifyconfig4 libkntlm4 libkparts4 libkpty4 libkrosscore4 libktexteditor4 libkxmlrpcclient4 libnepomuk4 libnepomukcore4abi1 libnepomukquery4a libnepomukutils4 libntrack-qt4-1 libntrack0 libphonon4 libplasma3 libpolkit-qt-1-1 libpoppler-qt4-4 libqapt2 libqapt2-runtime libqca2 libqt4-qt3support libsolid4 libsoprano4 libstreamanalyzer0 libstreams0 libthreadweaver4 libvirtodbc0 nepomuk-core nepomuk-core-data ntrack-module-libnl-0 odbcinst odbcinst1debian2 oxygen-icon-theme phonon phonon-backend-gstreamer plasma-scriptengine-javascript qapt-batch shared-desktop-ontologies soprano-daemon virtuoso-minimal virtuoso-opensource-6.1-bin virtuoso-opensource-6.1-common Use 'apt-get autoremove' to remove them. The following extra packages will be installed: apturl-kde icoutils kate-data katepart kde-runtime kde-runtime-data kdelibs-bin kdelibs5-data kdelibs5-plugins kdesudo kdoctools kubuntu-debug-installer libattica0.4 libdlrestrictions1 libkactivities-bin libkactivities-models1 libkactivities6 libkatepartinterfaces4 libkcmutils4 libkde3support4 libkdeclarative5 libkdecore5 libkdesu5 libkdeui5 libkdewebkit5 libkdnssd4 libkemoticons4 libkfile4 libkhtml5 libkidletime4 libkio5 libkjsapi4 libkjsembed4 libkmediaplayer4 libknewstuff3-4 libknotifyconfig4 libkntlm4 libkparts4 libkpty4 libkrosscore4 libktexteditor4 libkxmlrpcclient4 libnepomuk4 libnepomukcore4abi1 libnepomukquery4a libnepomukutils4 libntrack-qt4-1 libntrack0 libphonon4 libplasma3 libpolkit-qt-1-1 libpoppler-qt4-4 libqapt2 libqapt2-runtime libqca2 libqt4-qt3support libsolid4 libsoprano4 libstreamanalyzer0 libstreams0 libthreadweaver4 libvirtodbc0 libxml2-utils nepomuk-core nepomuk-core-data ntrack-module-libnl-0 odbcinst odbcinst1debian2 oxygen-icon-theme phonon phonon-backend-gstreamer plasma-scriptengine-javascript qapt-batch shared-desktop-ontologies soprano-daemon virtuoso-minimal virtuoso-opensource-6.1-bin virtuoso-opensource-6.1-common Suggested packages: libterm-readline-gnu-perl libterm-readline-perl-perl djvulibre-bin finger hspell libqca2-plugin-cyrus-sasl libqca2-plugin-gnupg libqca2-plugin-ossl phonon-backend-vlc phonon-backend-xine phonon-backend-mplayer The following packages will be REMOVED: aptoncd* apturl* mintupdate* mintwelcome* synaptic* The following NEW packages will be installed: apturl-kde icoutils kate-data katepart kde-runtime kde-runtime-data kdelibs-bin kdelibs5-data kdelibs5-plugins kdesudo kdoctools kubuntu-debug-installer libattica0.4 libdlrestrictions1 libkactivities-bin libkactivities-models1 libkactivities6 libkatepartinterfaces4 libkcmutils4 libkde3support4 libkdeclarative5 libkdecore5 libkdesu5 libkdeui5 libkdewebkit5 libkdnssd4 libkemoticons4 libkfile4 libkhtml5 libkidletime4 libkio5 libkjsapi4 libkjsembed4 libkmediaplayer4 libknewstuff3-4 libknotifyconfig4 libkntlm4 libkparts4 libkpty4 libkrosscore4 libktexteditor4 libkxmlrpcclient4 libnepomuk4 libnepomukcore4abi1 libnepomukquery4a libnepomukutils4 libntrack-qt4-1 libntrack0 libphonon4 libplasma3 libpolkit-qt-1-1 libpoppler-qt4-4 libqapt2 libqapt2-runtime libqca2 libqt4-qt3support libsolid4 libsoprano4 libstreamanalyzer0 libstreams0 libthreadweaver4 libvirtodbc0 libxml2-utils nepomuk-core nepomuk-core-data ntrack-module-libnl-0 odbcinst odbcinst1debian2 oxygen-icon-theme phonon phonon-backend-gstreamer plasma-scriptengine-javascript qapt-batch shared-desktop-ontologies soprano-daemon virtuoso-minimal virtuoso-opensource-6.1-bin virtuoso-opensource-6.1-common 0 upgraded, 78 newly installed, 5 to remove and 0 not upgraded. Need to get 60.9 MB of archives. After this operation, 146 MB of additional disk space will be used. Do you want to continue [Y/n]? n Abort. As you can see, apt-get is trying to install the same packages that it is asking me to autoremove. Could someone please tell me, how to uninstall synaptic properly? Or am I missing something? Just for the record, I also did, sudo apt-get autoremove --purge like it asked me to ... and this is what I got, Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 6 not upgraded.

  Read the article

• T-SQL (SCD) Slowly Changing Dimension Type 2 using a merge statement

  - by AtulThakor

  Working on stored procedure recently which loads records into a data warehouse I found that the existing record was being expired using an update statement followed by an insert to add the new active record. Playing around with the merge statement you can actually expire the current record and insert a new record within one clean statement. This is how the statement works, we do the normal merge statement to insert a record when there is no match, if we match the record we update the existing record by expiring it and deactivating. At the end of the merge statement we use the output statement to output the staging values for the update,  we wrap the whole merge statement within an insert statement and add new rows for the records which we inserted. I’ve added the full script at the bottom so you can paste it and play around.   1: INSERT INTO ExampleFactUpdate 2: (PolicyID, 3: Status) 4: SELECT -- these columns are returned from the output statement 5: PolicyID, 6: Status 7: FROM 8: ( 9: -- merge statement on unique id in this case Policy_ID 10: MERGE dbo.ExampleFactUpdate dp 11: USING dbo.ExampleStag s 12: ON dp.PolicyID = s.PolicyID 13: WHEN NOT MATCHED THEN -- when we cant match the record we insert a new record record and this is all that happens 14: INSERT (PolicyID,Status) 15: VALUES (s.PolicyID, s.Status) 16: WHEN MATCHED --if it already exists 17: AND ExpiryDate IS NULL -- and the Expiry Date is null 18: THEN 19: UPDATE 20: SET 21: dp.ExpiryDate = getdate(), --we set the expiry on the existing record 22: dp.Active = 0 -- and deactivate the existing record 23: OUTPUT $Action MergeAction, s.PolicyID, s.Status -- the output statement returns a merge action which can 24: ) MergeOutput -- be insert/update/delete, on our example where a record has been updated (or expired in our case 25: WHERE -- we'll filter using a where clause 26: MergeAction = 'Update'; -- here   Complete source for example 1: if OBJECT_ID('ExampleFactUpdate') > 0 2: drop table ExampleFactUpdate 3:  4: Create Table ExampleFactUpdate( 5: ID int identity(1,1), 3: go 6: PolicyID varchar(100), 7: Status varchar(100), 8: EffectiveDate datetime default getdate(), 9: ExpiryDate datetime, 10: Active bit default 1 11: ) 12:  13:  14: insert into ExampleFactUpdate( 15: PolicyID, 16: Status) 17: select 18: 1, 19: 'Live' 20:  21: /*Create Staging Table*/ 22: if OBJECT_ID('ExampleStag') > 0 23: drop table ExampleStag 24: go 25:  26: /*Create example fact table */ 27: Create Table ExampleStag( 28: PolicyID varchar(100), 29: Status varchar(100)) 30:  31: --add some data 32: insert into ExampleStag( 33: PolicyID, 34: Status) 35: select 36: 1, 37: 'Lapsed' 38: union all 39: select 40: 2, 41: 'Quote' 42:  43: select * 44: from ExampleFactUpdate 45:  46: select * 47: from ExampleStag 48:  49:  50: INSERT INTO ExampleFactUpdate 51: (PolicyID, 52: Status) 53: SELECT -- these columns are returned from the output statement 54: PolicyID, 55: Status 56: FROM 57: ( 58: -- merge statement on unique id in this case Policy_ID 59: MERGE dbo.ExampleFactUpdate dp 60: USING dbo.ExampleStag s 61: ON dp.PolicyID = s.PolicyID 62: WHEN NOT MATCHED THEN -- when we cant match the record we insert a new record record and this is all that happens 63: INSERT (PolicyID,Status) 64: VALUES (s.PolicyID, s.Status) 65: WHEN MATCHED --if it already exists 66: AND ExpiryDate IS NULL -- and the Expiry Date is null 67: THEN 68: UPDATE 69: SET 70: dp.ExpiryDate = getdate(), --we set the expiry on the existing record 71: dp.Active = 0 -- and deactivate the existing record 72: OUTPUT $Action MergeAction, s.PolicyID, s.Status -- the output statement returns a merge action which can 73: ) MergeOutput -- be insert/update/delete, on our example where a record has been updated (or expired in our case 74: WHERE -- we'll filter using a where clause 75: MergeAction = 'Update'; -- here 76:  77:  78: select * 79: from ExampleFactUpdate 80: 

  Read the article

• NHibernate Pitfalls: Custom Types and Detecting Changes

  - by Ricardo Peres

  This is part of a series of posts about NHibernate Pitfalls. See the entire collection here. NHibernate supports the declaration of properties of user-defined types, that is, not entities, collections or primitive types. These are used for mapping a database columns, of any type, into a different type, which may not even be an entity; think, for example, of a custom user type that converts a BLOB column into an Image. User types must implement interface NHibernate.UserTypes.IUserType. This interface specifies an Equals method that is used for comparing two instances of the user type. If this method returns false, the entity is marked as dirty, and, when the session is flushed, will trigger an UPDATE. So, in your custom user type, you must implement this carefully so that it is not mistakenly considered changed. For example, you can cache the original column value inside of it, and compare it with the one in the other instance. Let’s see an example implementation of a custom user type that converts a Byte[] from a BLOB column into an Image: 1: [Serializable] 2: public sealed class ImageUserType : IUserType 3: { 4: private Byte[] data = null; 5: 6: public ImageUserType() 7: { 8: this.ImageFormat = ImageFormat.Png; 9: } 10: 11: public ImageFormat ImageFormat 12: { 13: get; 14: set; 15: } 16: 17: public Boolean IsMutable 18: { 19: get 20: { 21: return (true); 22: } 23: } 24: 25: public Object Assemble(Object cached, Object owner) 26: { 27: return (cached); 28: } 29: 30: public Object DeepCopy(Object value) 31: { 32: return (value); 33: } 34: 35: public Object Disassemble(Object value) 36: { 37: return (value); 38: } 39: 40: public new Boolean Equals(Object x, Object y) 41: { 42: return (Object.Equals(x, y)); 43: } 44: 45: public Int32 GetHashCode(Object x) 46: { 47: return ((x != null) ? x.GetHashCode() : 0); 48: } 49: 50: public override Int32 GetHashCode() 51: { 52: return ((this.data != null) ? this.data.GetHashCode() : 0); 53: } 54: 55: public override Boolean Equals(Object obj) 56: { 57: ImageUserType other = obj as ImageUserType; 58: 59: if (other == null) 60: { 61: return (false); 62: } 63: 64: if (Object.ReferenceEquals(this, other) == true) 65: { 66: return (true); 67: } 68: 69: return (this.data.SequenceEqual(other.data)); 70: } 71: 72: public Object NullSafeGet(IDataReader rs, String[] names, Object owner) 73: { 74: Int32 index = rs.GetOrdinal(names[0]); 75: Byte[] data = rs.GetValue(index) as Byte[]; 76: 77: this.data = data as Byte[]; 78: 79: if (data == null) 80: { 81: return (null); 82: } 83: 84: using (MemoryStream stream = new MemoryStream(this.data ?? new Byte[0])) 85: { 86: return (Image.FromStream(stream)); 87: } 88: } 89: 90: public void NullSafeSet(IDbCommand cmd, Object value, Int32 index) 91: { 92: if (value != null) 93: { 94: Image data = value as Image; 95: 96: using (MemoryStream stream = new MemoryStream()) 97: { 98: data.Save(stream, this.ImageFormat); 99: value = stream.ToArray(); 100: } 101: } 102: 103: (cmd.Parameters[index] as DbParameter).Value = value ?? DBNull.Value; 104: } 105: 106: public Object Replace(Object original, Object target, Object owner) 107: { 108: return (original); 109: } 110: 111: public Type ReturnedType 112: { 113: get 114: { 115: return (typeof(Image)); 116: } 117: } 118: 119: public SqlType[] SqlTypes 120: { 121: get 122: { 123: return (new SqlType[] { new SqlType(DbType.Binary) }); 124: } 125: } 126: } In this case, we need to cache the original Byte[] data because it’s not easy to compare two Image instances, unless, of course, they are the same.

  Read the article

• Upgraded to 12.04 now wifi doesn't work

  - by Benito Kestelman

  My laptop's wifi stopped working when I upgraded to Ubuntu 12.04 (wired works). I just reinstalled 12.04 over my old 12.04 on which wifi didn't work either in an attempt to restore any settings I may have accidentally changed, but it still doesn't work. I also used a wired connection to install updates in case this bug has been fixed, but it has not. Here is the result of sudo lshw -class network: *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:5f:5b:f4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-29-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 14:da:e9:c0:da:78 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) Here is rfkill list all: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-wimax: WiMAX Soft blocked: no Hard blocked: no lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 8087:07d6 Intel Corp. Bus 001 Device 004: ID 13d3:5710 IMC Networks Bus 002 Device 003: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth Bus 003 Device 003: ID 0781:5530 SanDisk Corp. Cruzer lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) 03:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller 04:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)

  Read the article

• Is the Leptonica implementation of 'Modified Median Cut' not using the median at all?

  - by TheCodeJunkie

  I'm playing around a bit with image processing and decided to read up on how color quantization worked and after a bit of reading I found the Modified Median Cut Quantization algorithm. I've been reading the code of the C implementation in Leptonica library and came across something I thought was a bit odd. Now I want to stress that I am far from an expert in this area, not am I a math-head, so I am predicting that this all comes down to me not understanding all of it and not that the implementation of the algorithm is wrong at all. The algorithm states that the vbox should be split along the lagest axis and that it should be split using the following logic The largest axis is divided by locating the bin with the median pixel (by population), selecting the longer side, and dividing in the center of that side. We could have simply put the bin with the median pixel in the shorter side, but in the early stages of subdivision, this tends to put low density clusters (that are not considered in the subdivision) in the same vbox as part of a high density cluster that will outvote it in median vbox color, even with future median-based subdivisions. The algorithm used here is particularly important in early subdivisions, and 3is useful for giving visible but low population color clusters their own vbox. This has little effect on the subdivision of high density clusters, which ultimately will have roughly equal population in their vboxes. For the sake of the argument, let's assume that we have a vbox that we are in the process of splitting and that the red axis is the largest. In the Leptonica algorithm, on line 01297, the code appears to do the following Iterate over all the possible green and blue variations of the red color For each iteration it adds to the total number of pixels (population) it's found along the red axis For each red color it sum up the population of the current red and the previous ones, thus storing an accumulated value, for each red note: when I say 'red' I mean each point along the axis that is covered by the iteration, the actual color may not be red but contains a certain amount of red So for the sake of illustration, assume we have 9 "bins" along the red axis and that they have the following populations 4 8 20 16 1 9 12 8 8 After the iteration of all red bins, the partialsum array will contain the following count for the bins mentioned above 4 12 32 48 49 58 70 78 86 And total would have a value of 86 Once that's done it's time to perform the actual median cut and for the red axis this is performed on line 01346 It iterates over bins and check they accumulated sum. And here's the part that throws me of from the description of the algorithm. It looks for the first bin that has a value that is greater than total/2 Wouldn't total/2 mean that it is looking for a bin that has a value that is greater than the average value and not the median ? The median for the above bins would be 49 The use of 43 or 49 could potentially have a huge impact on how the boxes are split, even though the algorithm then proceeds by moving to the center of the larger side of where the matched value was.. Another thing that puzzles me a bit is that the paper specified that the bin with the median value should be located, but does not mention how to proceed if there are an even number of bins.. the median would be the result of (a+b)/2 and it's not guaranteed that any of the bins contains that population count. So this is what makes me thing that there are some approximations going on that are negligible because of how the split actually takes part at the center of the larger side of the selected bin. Sorry if it got a bit long winded, but I wanted to be as thoroughas I could because it's been driving me nuts for a couple of days now ;)

  Read the article

• SSLException: HelloRequest followed by an unexpected handshake message

  - by mseebach

  I'm trying to connect to a webservice over SSL using Apache Commons HttpClient 3.1, using this: String url = "https://archprod.service.eogs.dk/cvronline/esb/LegalUnitGetSSLServicePort"; HttpClient client = new HttpClient(); PostMethod post = new PostMethod(url); StringRequestEntity entity = new StringRequestEntity(requestXml, "application/soap+xml", "utf-8"); post.setRequestEntity(entity); client.executeMethod(post); String response = post.getResponseBodyAsString(); And I get this exception: javax.net.ssl.SSLException: HelloRequest followed by an unexpected handshake message at com.sun.net.ssl.internal.ssl.Alerts.getSSLException(Alerts.java:190) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.fatal(SSLSocketImpl.java:1623) at com.sun.net.ssl.internal.ssl.Handshaker.fatalSE(Handshaker.java:198) at com.sun.net.ssl.internal.ssl.Handshaker.fatalSE(Handshaker.java:188) at com.sun.net.ssl.internal.ssl.ClientHandshaker.serverHelloRequest(ClientHandshaker.java:286) at com.sun.net.ssl.internal.ssl.ClientHandshaker.processMessage(ClientHandshaker.java:114) at com.sun.net.ssl.internal.ssl.Handshaker.processLoop(Handshaker.java:525) at com.sun.net.ssl.internal.ssl.Handshaker.process_record(Handshaker.java:465) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.readRecord(SSLSocketImpl.java:884) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.readDataRecord(SSLSocketImpl.java:746) at com.sun.net.ssl.internal.ssl.AppInputStream.read(AppInputStream.java:75) at java.io.BufferedInputStream.fill(BufferedInputStream.java:218) at java.io.BufferedInputStream.read(BufferedInputStream.java:237) at org.apache.commons.httpclient.HttpParser.readRawLine(HttpParser.java:78) at org.apache.commons.httpclient.HttpParser.readLine(HttpParser.java:106) at org.apache.commons.httpclient.HttpConnection.readLine(HttpConnection.java:1116) at org.apache.commons.httpclient.HttpMethodBase.readStatusLine(HttpMethodBase.java:1973) at org.apache.commons.httpclient.HttpMethodBase.readResponse(HttpMethodBase.java:1735) at org.apache.commons.httpclient.HttpMethodBase.execute(HttpMethodBase.java:1098) at org.apache.commons.httpclient.HttpMethodDirector.executeWithRetry(HttpMethodDirector.java:398) at org.apache.commons.httpclient.HttpMethodDirector.executeMethod(HttpMethodDirector.java:171) at org.apache.commons.httpclient.HttpClient.executeMethod(HttpClient.java:397) at org.apache.commons.httpclient.HttpClient.executeMethod(HttpClient.java:323) A request to the same URL on the same machine, using curl, works fine - and if I change the URL to e.g. https://www.verisign.com, it works fine in Java, too. So it appears to be the specific combination of Java and that host, not a general problem. Ubuntu 10.04 beta, Sun JDK 1.6.0_19 (same problem in Ubuntu's bundled OpenJDK 6b18~pre4). Any ideas what's going wrong? Thanks!

  Read the article

• Uploadify with ruby on rails 'bad content body' 500 Internal Server Error

  - by Mr_Nizzle

  I'm Getting this error in my development log while uploadify is uploading the file and in the view i get an 'IO ERROR' beside filename. /!\ FAILSAFE /!\ Thu Mar 18 11:54:53 -0500 2010 Status: 500 Internal Server Error bad content body /usr/lib/ruby/gems/1.8/gems/rack-1.0.1/lib/rack/utils.rb:351:in `parse_multipart' /usr/lib/ruby/gems/1.8/gems/rack-1.0.1/lib/rack/utils.rb:323:in `loop' /usr/lib/ruby/gems/1.8/gems/rack-1.0.1/lib/rack/utils.rb:323:in `parse_multipart' /usr/lib/ruby/gems/1.8/gems/rack-1.0.1/lib/rack/request.rb:133:in `POST' /usr/lib/ruby/gems/1.8/gems/rack-1.0.1/lib/rack/methodoverride.rb:15:in `call' /usr/lib/ruby/gems/1.8/gems/actionpack-2.3.3/lib/action_controller/params_parser.rb:15:in `call' /usr/lib/ruby/gems/1.8/gems/actionpack-2.3.3/lib/action_controller/session/cookie_store.rb:93:in `call' /usr/lib/ruby/gems/1.8/gems/actionpack-2.3.3/lib/action_controller/reloader.rb:29:in `call' /usr/lib/ruby/gems/1.8/gems/actionpack-2.3.3/lib/action_controller/failsafe.rb:26:in `call' /usr/lib/ruby/gems/1.8/gems/rack-1.0.1/lib/rack/lock.rb:11:in `call' /usr/lib/ruby/gems/1.8/gems/rack-1.0.1/lib/rack/lock.rb:11:in `synchronize' /usr/lib/ruby/gems/1.8/gems/rack-1.0.1/lib/rack/lock.rb:11:in `call' /usr/lib/ruby/gems/1.8/gems/actionpack-2.3.3/lib/action_controller/dispatcher.rb:106:in `call' /usr/lib/ruby/gems/1.8/gems/rack-1.0.1/lib/rack/content_length.rb:13:in `call' /usr/lib/ruby/gems/1.8/gems/rack-1.0.1/lib/rack/handler/fastcgi.rb:58:in `serve' /usr/lib/ruby/gems/1.8/gems/rails-2.3.3/lib/fcgi_handler.rb:103:in `process_request' /usr/lib/ruby/gems/1.8/gems/rails-2.3.3/lib/fcgi_handler.rb:153:in `with_signal_handler' /usr/lib/ruby/gems/1.8/gems/rails-2.3.3/lib/fcgi_handler.rb:101:in `process_request' /usr/lib/ruby/gems/1.8/gems/rails-2.3.3/lib/fcgi_handler.rb:78:in `process_each_request' /usr/lib/ruby/gems/1.8/gems/rails-2.3.3/lib/fcgi_handler.rb:77:in `each' /usr/lib/ruby/gems/1.8/gems/rails-2.3.3/lib/fcgi_handler.rb:77:in `process_each_request' /usr/lib/ruby/gems/1.8/gems/rails-2.3.3/lib/fcgi_handler.rb:76:in `catch' /usr/lib/ruby/gems/1.8/gems/rails-2.3.3/lib/fcgi_handler.rb:76:in `process_each_request' /usr/lib/ruby/gems/1.8/gems/rails-2.3.3/lib/fcgi_handler.rb:51:in `process!' /usr/lib/ruby/gems/1.8/gems/rails-2.3.3/lib/fcgi_handler.rb:23:in `process!' dispatch.fcgi:24 any idea on this?

  Read the article

• Selenium IDE - Passing a URL string variable into a conditional 'gotoIf' statement throws a Syntax e

  - by user318568

  I am trying to store the current url (http://example.com)in a variable and compare it with another string as a condition in the gotoIf command (part of the gotoIf extension.js): storeLocation || url gotoIf || ${url}=="http://example.com" || label When I run this seleniun ide throws this error: [error] Unexpected Exception: message -> syntax error, fileName -> chrome://selenium-ide/content/tools.js -> file:///C:/Users/David%20Cunningham/Desktop/extensions_js/extensions.js, lineNumber -> 183, stack -> eval("http://example.com==\"http://example.com\"")@:0 ("http://example.com==\"http://example.com\"","label1")@chrome://selenium-ide/content/tools.js -> file:///C:/Users/David%20Cunningham/Desktop/extensions_js/extensions.js:183 ("http://example.com==\"http://example.com\"","label1")@chrome://selenium-ide/content/selenium/scripts/htmlutils.js:60 ([object Object],[object Object])@chrome://selenium-ide/content/selenium/scripts/selenium-commandhandlers.js:310 ()@chrome://selenium-ide/content/selenium/scripts/selenium-executionloop.js:112 (6)@chrome://selenium-ide/content/selenium/scripts/selenium-executionloop.js:78 (6)@chrome://selenium-ide/content/selenium/scripts/htmlutils.js:60 , name -> SyntaxError storeLocation should return a String so why am i getting this error, what is wrong with the syntax and how do I declare this command?

  Read the article

• NserviceBus throws exception when referencing a Nettiers assembly

  - by IGoor

  We use nettiers as a our data layer, and we recently have started looking at using NServiceBus, but we have hit a wall. We have a windows service which hosts NSB and references our Nettiers assembly. the service is throwing an exception when the following line is encountered. var Bus = Configure.With().SpringBuilder() .XmlSerializer() .MsmqTransport() .IsTransactional(false) .PurgeOnStartup(false) .UnicastBus() .ImpersonateSender(false) .CreateBus() .Start(); the exceptions that is throw is: Unable to load one or more of the requested types. Retrieve the LoaderExceptions property for more information. the loader exception message is: Could not load file or assembly 'Microsoft.Practices.Unity, Version=1.2.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35' or one of its dependencies. The system cannot find the file specified.":"Microsoft.Practices.Unity, Version=1.2.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35 stacktrace is: at System.Reflection.Module._GetTypesInternal(StackCrawlMark& stackMark) at System.Reflection.Assembly.GetTypes() at NServiceBus.Configure.<>c__DisplayClass1.<With>b__0(Assembly a) in d:\BuildAgent-03\work\672d81652eaca4e1\src\config\NServiceBus.Config\Configure.cs:line 122 at System.Array.ForEach[T](T[] array, Action`1 action) at NServiceBus.Configure.With(Assembly[] assemblies) in d:\BuildAgent-03\work\672d81652eaca4e1\src\config\NServiceBus.Config\Configure.cs:line 122 at NServiceBus.Configure.With(IEnumerable`1 assemblies) in d:\BuildAgent-03\work\672d81652eaca4e1\src\config\NServiceBus.Config\Configure.cs:line 111 at NServiceBus.Configure.With(String probeDirectory) in d:\BuildAgent-03\work\672d81652eaca4e1\src\config\NServiceBus.Config\Configure.cs:line 101 at NServiceBus.Configure.With() in d:\BuildAgent-03\work\672d81652eaca4e1\src\config\NServiceBus.Config\Configure.cs:line 78 at MessageSender.Program.Main(String[] args) in C:\Development\NSBTest4\MessageSender\Program.cs:line 18 without the nettiers reference NSB works fine. Any idea what the problem is and how to solve it? thanks.

  Read the article

• HTTP 500 ERROR on CAS Server while setting SSLVerifyClent as "required"

  - by Huiyu.Bird

  I have 3 servers, a Apache Server, a JBOSS Server and a CAS Server for SSO. The Apache Server resolve all request with a domain such as www.request.com, and the path of CAS Server is www.request.com/cas, and JBOSS Server is www.request.com/jboss (This app got a CAS client). My problem is if I set SSLVerifyClient require for the NameVirtualHost of www.request.com in my Apache Server, I got a HTTP 500 error during the redirecting to the JBOSS Server(http://www.request.com/jboss), after logined in the CAS login page successfully. But everything goes successfully if there is no SSLVerifyClient require . Error logs of my Apache Server : [Mon Apr 19 17:07:25 2010] [error] Re-negotiation handshake failed: Not accepted by client!? Error logs of my JBOSS Server : 2010-04-19 17:29:57,263 ERROR [org.apache.catalina.core.ContainerBase.[jboss.web].[localhost].[/jboss].[jsp]] (ajp-0.0.0.0-8009-1) Servlet.service() for servlet jsp threw exception org.jasig.cas.client.validation.TicketValidationException: The CAS server returned no response. at org.jasig.cas.client.validation.AbstractUrlBasedTicketValidator.validate(AbstractUrlBasedTicketValidator.java:162) at org.jasig.cas.client.validation.AbstractTicketValidationFilter.doFilter(AbstractTicketValidationFilter.java:129) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.jasig.cas.client.authentication.AuthenticationFilter.doFilter(AuthenticationFilter.java:103) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.jasig.cas.client.session.SingleSignOutFilter.doFilter(SingleSignOutFilter.java:78) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.springframework.web.filter.CharacterEncodingFilter.doFilterInternal(CharacterEncodingFilter.java:96) at org.springframework.web.filter.OncePerRequestFilter.doFilter(OncePerRequestFilter.java:75) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.jboss.web.tomcat.filters.ReplyHeaderFilter.doFilter(ReplyHeaderFilter.java:96) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.apache.catalina.core.StandardWrapperValve.in Any tips will be highly appreciated. Thanks in advance.

  Read the article

• java.lang.NoSuchMethodError: org.w3c.dom.Document.setDocumentURI

  - by mike00000888

  I am getting a NoSuchMethodError error for org.w3c.dom.Document.setDocumentURI. This is strange, as I have rt.jar in the JAVA_HOME path. I am creating a web service using CXF, and the error seem to be coming out of CXF: java.lang.NoSuchMethodError: org.w3c.dom.Document.setDocumentURI(Ljava/lang/String;)V org.apache.cxf.staxutils.StaxUtils.read(StaxUtils.java:760) org.apache.cxf.wsdl11.WSDLManagerImpl.loadDefinition(WSDLManagerImpl.java:219) org.apache.cxf.wsdl11.WSDLManagerImpl.getDefinition(WSDLManagerImpl.java:179) org.apache.cxf.wsdl11.WSDLServiceFactory.(WSDLServiceFactory.java:91) org.apache.cxf.service.factory.ReflectionServiceFactoryBean.buildServiceFromWSDL(ReflectionServiceFactoryBean.java:403) org.apache.cxf.service.factory.ReflectionServiceFactoryBean.initializeServiceModel(ReflectionServiceFactoryBean.java:528) org.apache.cxf.service.factory.ReflectionServiceFactoryBean.create(ReflectionServiceFactoryBean.java:278) org.apache.cxf.jaxws.support.JaxWsServiceFactoryBean.create(JaxWsServiceFactoryBean.java:178) org.apache.cxf.frontend.AbstractWSDLBasedEndpointFactory.createEndpoint(AbstractWSDLBasedEndpointFactory.java:100) org.apache.cxf.frontend.ServerFactoryBean.create(ServerFactoryBean.java:105) org.apache.cxf.jaxws.JaxWsServerFactoryBean.create(JaxWsServerFactoryBean.java:167) org.apache.cxf.jaxws.EndpointImpl.getServer(EndpointImpl.java:349) org.apache.cxf.jaxws.EndpointImpl.doPublish(EndpointImpl.java:262) org.apache.cxf.jaxws.EndpointImpl.publish(EndpointImpl.java:212) org.apache.cxf.jaxws.EndpointImpl.publish(EndpointImpl.java:407) sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) java.lang.reflect.Method.invoke(Method.java:597) org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.invokeCustomInitMethod(AbstractAutowireCapableBeanFactory.java:1414) org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.invokeInitMethods(AbstractAutowireCapableBeanFactory.java:1375) org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.initializeBean(AbstractAutowireCapableBeanFactory.java:1335) org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.doCreateBean(AbstractAutowireCapableBeanFactory.java:473) org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory$1.run(AbstractAutowireCapableBeanFactory.java:409) java.security.AccessController.doPrivileged(Native Method) org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.createBean(AbstractAutowireCapableBeanFactory.java:380) org.springframework.beans.factory.support.AbstractBeanFactory$1.getObject(AbstractBeanFactory.java:264) org.springframework.beans.factory.support.DefaultSingletonBeanRegistry.getSingleton(DefaultSingletonBeanRegistry.java:222) org.springframework.beans.factory.support.AbstractBeanFactory.doGetBean(AbstractBeanFactory.java:261) org.springframework.beans.factory.support.AbstractBeanFactory.getBean(AbstractBeanFactory.java:185) org.springframework.beans.factory.support.AbstractBeanFactory.getBean(AbstractBeanFactory.java:164) org.springframework.beans.factory.support.DefaultListableBeanFactory.preInstantiateSingletons(DefaultListableBeanFactory.java:429) org.springframework.context.support.AbstractApplicationContext.finishBeanFactoryInitialization(AbstractApplicationContext.java:728) org.springframework.context.support.AbstractApplicationContext.refresh(AbstractApplicationContext.java:380) org.apache.cxf.transport.servlet.CXFServlet.loadAdditionalConfig(CXFServlet.java:171) org.apache.cxf.transport.servlet.CXFServlet.updateContext(CXFServlet.java:139) org.apache.cxf.transport.servlet.CXFServlet.loadSpringBus(CXFServlet.java:101) org.apache.cxf.transport.servlet.CXFServlet.loadBus(CXFServlet.java:70) org.apache.cxf.transport.servlet.AbstractCXFServlet.init(AbstractCXFServlet.java:78) org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:102) org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:293) org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:849) org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.process(Http11Protocol.java:583) org.apache.tomcat.util.net.JIoEndpoint$Worker.run(JIoEndpoint.java:454) java.lang.Thread.run(Thread.java:619) Can someone offer some advice? Much thanks

  Read the article

• Selenium error on Win7

  - by hawkeye

  I'm starting Selenium server with the following on a command line: java -jar selenium-server.jar Here is the code: import com.thoughtworks.selenium.*; import java.util.regex.Pattern; import org.openqa.selenium.server.SeleniumServer; import junit.framework.*; public class orkut extends SeleneseTestCase { public void setUp() throws Exception { //SeleniumServer server = new SeleniumServer(); //server.start(); setUp("https://www.google.com/", "*firefox C:\\Program Files (x86)\\Mozilla Firefox\\firefox.exe"); } public void testOrkut() throws Exception { selenium.setTimeout("10000"); selenium.open("/accounts/ServiceLogin?service=orkut&hl=en-US&rm=false&continue=http%3A%2F%2Fwww.orkut.com%2FRedirLogin%3Fmsg%3D0&cd=IN&skipvpage=true&sendvemail=false"); selenium.type("Email", "username"); selenium.type("Passwd", "password"); selenium.click("signIn"); selenium.selectFrame("orkutFrame"); selenium.click("link=Communities"); selenium.waitForPageToLoad("10000"); } public static Test suite() { return new TestSuite(orkut.class); } public void tearDown(){ selenium.stop(); } public static void main(String args[]) { junit.textui.TestRunner.run(suite()); } } Here is the error: .E Time: 33.386 There was 1 error: 1) testOrkut(orkut)java.lang.RuntimeException: Could not start Selenium session: Failed to start new browser session: Unable to delete file C:\Users\user\AppData\Local\Temp\customProfileDir78cf02e3efca4772a71525c4a7523cac\parent.lock at com.thoughtworks.selenium.DefaultSelenium.start(DefaultSelenium.java:89) at com.thoughtworks.selenium.SeleneseTestBase.setUp(SeleneseTestBase.java:123) at com.thoughtworks.selenium.SeleneseTestBase.setUp(SeleneseTestBase.java:104) at com.thoughtworks.selenium.SeleneseTestCase.setUp(SeleneseTestCase.java:78) at orkut.setUp(orkut.java:14) at com.thoughtworks.selenium.SeleneseTestCase.runBare(SeleneseTestCase.java:212) at orkut.main(orkut.java:37) Caused by: com.thoughtworks.selenium.SeleniumException: Failed to start new browser session: Unable to delete file C:\Users\M022534\AppData\Local\Temp\customProfileDir78cf02e3efca4772a71525c4a7523cac\parent.lock at com.thoughtworks.selenium.HttpCommandProcessor.throwAssertionFailureExceptionOrError(HttpCommandProcessor.java:97) at com.thoughtworks.selenium.HttpCommandProcessor.doCommand(HttpCommandProcessor.java:91) at com.thoughtworks.selenium.HttpCommandProcessor.getString(HttpCommandProcessor.java:262) at com.thoughtworks.selenium.HttpCommandProcessor.start(HttpCommandProcessor.java:223) at com.thoughtworks.selenium.DefaultSelenium.start(DefaultSelenium.java:81) ... 16 more FAILURES!!! Tests run: 1, Failures: 0, Errors: 1

  Read the article

• Interoperability between Weblogic 10.3.1 and Oracle BPM 10.3.1

  - by alfredozn

  Hi, Im migrating an ALBPM 6.5 running on a WLS 10.0 to an Oracle BPM 10.3.1 running on WLS 10.3.1 I got some problems with the Oracle driver because the old driver (weblogic.jdbcx.oracle.OracleDataSource) was definitely removed from the server and is not longer supported. Instead I used the thin driver (oracle.jdbc.xa.OracleXADataSource), the database migration was executed succesfully but after that, when I try to deploy the engine ear in WebLogic I got exceptions asociated to the driver: [ (cont) ] Main: Caused by: weblogic.application.ModuleException: [HTTP:101216]Servlet: "engineStartup" failed to preload on startup in Web application: "/albpmServices/albpm_engine". [ (cont) ] Main: fuego.directory.DirectoryRuntimeException: Exception [java.sql.SQLException: Invalid column type]. [ (cont) ] Main: at fuego.directory.DirectoryRuntimeException.wrapException(DirectoryRuntimeException.java:85) [ (cont) ] Main: at fuego.directory.provider.jdbc.oracle.OraclePersistenceManager.mapSQLException(OraclePersistenceManager.java:145) [ (cont) ] Main: at fuego.directory.provider.jdbc.datadirect.oracle.DataDirectOraclePersistenceManager.mapSQLException(DataDirectOraclePersistenceManager.java:51) [ (cont) ] Main: at fuego.directory.provider.jdbc.JDBCServiceAccessor.mapSQLException(JDBCServiceAccessor.java:78) [ (cont) ] Main: at fuego.directory.provider.jdbc.JDBCObjectPropertiesAccessor.fetchAllDirectoryProperties(JDBCObjectPropertiesAccessor.java:442) [ (cont) ] Main: at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) I was looking around for a solution but all is pointing to use the old driver, I think isn't a good practice to force the server to use this driver after Oracle remove it completely. Any suggestions or similar experiences??

  Read the article

• Problem upgrading eclipse rcp app from 3.3 to 3.5 on Mac OS

  - by Alb

  I previously had an eclipse rcp app based on eclipse 3.3 pugins deployed on both windows and mac OS X 10.4. i'm now trying to port the app to java 1.6 and eclipse 3.5 (Build id: 20100218-1602) plugins on Mac OS X 10.5.8 (Leopard). I can launch the product from eclipse 3.5 on windows but not on Mac OS X. I have the 64bit cocoa eclipse IDE and java 6. In the launch configuration I set runtime JRE to JVM 1.6.0 and added required plugins. The plugins validate and everything else looks similar to windows configuration where it works, but when I launch i only get the following two lines in the console: 2010-03-16 13:29:32.742 java[758:10b] [Java CocoaComponent compatibility mode]: Enabled 2010-03-16 13:29:32.744 java[758:10b] [Java CocoaComponent compatibility mode]: Setting timeout for SWT to 0.100000 and then the program appears to just hang indefinitely. There is nothing written to the .log file so I'm not sure what error there is. EDIT: Here's what Yourkit profiling says before all cpu activity stops. +----------------------------------------------------------------------------+----------------+-----------------+ | Name | Time (ms) | Own Time (ms) | +----------------------------------------------------------------------------+----------------+-----------------+ | +---<All threads> | 2,799 100 % | | | | | | | | +---org.eclipse.equinox.launcher.Main.main(String[]) | 1,924 69% | 0 | | | | | | | +---org.eclipse.osgi.framework.eventmgr.EventManager$EventThread.run() | 632 23 % | 0 | | | | | | | +---java.lang.Thread.run() | 135 5 % | 0 | | | | | | | +---java.lang.ClassLoader.loadClassInternal(String) | 106 4 % | 0 | +----------------------------------------------------------------------------+----------------+-----------------+ , and this in the exceptions tab: Exception staticstics +----------------------------------------+--------------+ | Name | Count | +----------------------------------------+--------------+ | +---java.lang.ClassNotFoundException | 102 11 % | | | | | | +---java.net.MalformedURLException | 4 0 % | | | | | | +---java.lang.NoSuchMethodException | 3 0 % | | | | | | +---java.lang.NumberFormatException | 2 0 % | | | | | | +---java.io.FileNotFoundException | 1 0 % | | | | | | +---java.lang.UnsatisfiedLinkError | 1 0 % | +----------------------------------------+--------------+ and here's more details on the ClassNotFoundExceptions mentioned above: java.lang.ClassNotFoundException Start Level Event Dispatcher native ID: 0x8B0B group: 'main' 78 Thread-4 native ID: 0x10B group: 'main' 22 Framework Event Dispatcher native ID: 0xD207 group: 'main' 2 Anyone know why I don't see a trace for this in Eclipse or in any log files? any ideas where I should look? [Updated on: Tue, 16 March 2010 09:37]

  Read the article

• MKMapView loading all annotation views at once (including those that are outside the current rect)

  - by jmans

  Has anyone else run into this problem? Here's the code: - (MKAnnotationView *)mapView:(MKMapView *)mapView viewForAnnotation:(WWMapAnnotation *)annotation { // Only return an Annotation view for the placemarks. Ignore for the current location--the iPhone SDK will place a blue ball there. NSLog(@"Request for annotation view"); if ([annotation isKindOfClass:[WWMapAnnotation class]]){ MKPinAnnotationView *browse_map_annot_view = (MKPinAnnotationView *)[mapView dequeueReusableAnnotationViewWithIdentifier:@"BrowseMapAnnot"]; if (!browse_map_annot_view) { browse_map_annot_view = [[[MKPinAnnotationView alloc] initWithAnnotation:annotation reuseIdentifier:@"BrowseMapAnnot"] autorelease]; NSLog(@"Creating new annotation view"); } else { NSLog(@"Recycling annotation view"); browse_map_annot_view.annotation = annotation; } ... As soon as the view is displayed, I get 2009-08-05 13:12:03.332 xxx[24308:20b] Request for annotation view 2009-08-05 13:12:03.333 xxx[24308:20b] Creating new annotation view 2009-08-05 13:12:03.333 xxx[24308:20b] Request for annotation view 2009-08-05 13:12:03.333 xxx[24308:20b] Creating new annotation view and on and on, for every annotation (~60) I've added. The map (correctly) only displays the two annotations in the current rect. I am setting the region in viewDidLoad: if (center_point.latitude == 0) { center_point.latitude = 35.785098; center_point.longitude = -78.669899; } if (map_span.latitudeDelta == 0) { map_span.latitudeDelta = .001; map_span.longitudeDelta = .001; } map_region.center = center_point; map_region.span = map_span; NSLog(@"Setting initial map center and region"); [browse_map_view setRegion:map_region animated:NO]; The log entry for the region being set is printed to the console before any annotation views are requested. The problem here is that since all of the annotations are being requested at once, [mapView dequeueReusableAnnotationViewWithIdentifier] does nothing, since there are unique MKAnnotationViews for every annotation on the map. This is leading to memory problems for me. One possible issue is that these annotations are clustered in a pretty small space (~1 mile radius). Although the map is zoomed in pretty tight in viewDidLoad (latitude and longitude delta .001), it still loads all of the annotation views at once. Thanks...

  Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >