Search Results

Search found 604 results on 25 pages for 'interrupt'.

Page 18/25 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

  • Sudden and frequent hangs on desktop computer: mobo or CPU fault?

    - by djechelon
    I have a desktop computer equipped with an ASUS Crosshair 2 Formula and a Phenom x6 3.2GHz CPU. My problem is that often the computer will hang all of a sudden, completely stopping responding. When that occurs, reset key is inoperative and power button turns the computer off but is unable to turn it back on. I have to physically disconnect power cable. The problem can occur anytime, when I'm booting Windows, when I'm logging in, when I'm listening to a song, when I'm browsing Internet, etc. It always occurs after very few minutes of 3D gameplay I thought it was a video card fault. I had 3 8800GTX so I could try all combinations of them: didn't fix I thought it was a RAM problem: I tried running with only a subset of my DDR2 banks but didn't fix. Almost every time I have to reset and reconfigure BIOS (without AHCI, Win7 won't boot, so I need to restore a few things). If I enable AMD Live, Cool&Quiet or other things from CPU configuration menu I'll be sure that the computer won't reach Windows desktop in 99% of cases (it randomly hangs somewhere in the boot process or even in the BIOS POST). Another interesting thing is that during the POST process the computer always takes unusually long time detecting USB devices (LCD POSTer shows USB INIT), and I've also tried disconnecting all USB devices but didn't take less time to POST BIOS revision is 2702, the latest. Today I found a different behaviour once: during boot screen I got a BSOD with error Stop 0x00000101 A clock interrupt was not received on a secondary processor within the allocated time interval, and this is usually related to overclocking, but I never overclocked my CPU. Judging from the description of my problem, hoping someone had the same and fixed, and since I don't have a spare CPU or motherboard for replacement, I'd like to ask if you think this is a problem with faulty CPU or faulty motherboard, and if I can perform additional tests (I mean software tests because of my lack of spare components) to identify the component to replace.

    Read the article

  • Configure static IPv6 on Ubuntu

    - by Charles Offenbacher
    I'm trying to configure IPv6 on a dedicated Ubuntu server. My provider gave me a "/64" (whatever that is - I'm still confused) of IPv6 addresses. However, when I try to use them, I can't ping anything. What do I do? :( # ping6 ipv6.google.com PING ipv6.google.com(vx-in-x63.1e100.net) 56 data bytes From fe80::219:d1ff:fefb:42d8 icmp_seq=1 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=2 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=3 Destination unreachable: Address unreachable --- ipv6.google.com ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2014ms # tracepath6 ipv6.google.com 1?: [LOCALHOST] 0.025ms pmtu 1500 1: fe80::219:d1ff:fefb:42d8%eth0 2000.022ms !H Resume: pmtu 1500 # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 64.***.***.*** netmask 255.255.255.248 gateway 64.***.***.*** iface eth0 inet6 static pre-up modprobe ipv6 address 2607:F878:1:***::1 netmask 64 gateway 2607:F878:1:***(same as address)::1 # ifconfig eth0 Link encap:Ethernet HWaddr 00:19:d1:fb:42:d8 inet addr:64.***.***.*** Bcast:64.***.***.*** Mask:255.255.255.248 inet6 addr: fe80::219:d1ff:fefb:42d8/64 Scope:Link inet6 addr: 2607:f878:1:***::1/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:52451 errors:0 dropped:0 overruns:0 frame:0 TX packets:39729 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6817761 (6.8 MB) TX bytes:6153835 (6.1 MB) Interrupt:41 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:166 errors:0 dropped:0 overruns:0 frame:0 TX packets:166 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:31714 (31.7 KB) TX bytes:31714 (31.7 KB)

    Read the article

  • Setting up /etc/network/interface file for KVM ubuntu 10.10

    - by Charles Thornton
    I am trying to setup KVM on Unbuntu 10.10 IFCONFIG DUMP: hydra(~}$ifconfig eth0 Link encap:Ethernet HWaddr 00:1b:fc:cb:77:eb inet addr:172.20.20.3 Bcast:172.20.20.255 Mask:255.255.255.0 inet6 addr: fe80::21b:fcff:fecb:77eb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1345 errors:0 dropped:0 overruns:0 frame:0 TX packets:1541 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:820414 (820.4 KB) TX bytes:317708 (317.7 KB) Interrupt:23 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) virbr0 Link encap:Ethernet HWaddr 0a:1e:fb:b4:77:84 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 inet6 addr: fe80::81e:fbff:feb4:7784/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:8934 (8.9 KB) hydra(~}$ QUESTION:: How should /etc/network/interfaces be setup?? The following attempt just kills my internet connection! --------- /etc/network/interfaces ------------- # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 172.20.20.3 netmask 255.255.255.0 network 172.20.20.0 broadcast 172.20.20.255 gateway 172.20.20.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off What am I doing wrong????

    Read the article

  • Host system resets (crashes) when using VMWare or VirtualBox and 64-bit guest systems

    - by sinni800
    I have been trying to install virtual systems on VMWare for a while now and encountered strange behaviour from my PC. The behaviour is as follows: On "automatic" virtualization mode it either outputs a cryptic error message (can MAYBE give later, if I can reproduce) right on startup (before even the BIOS) or it resets the complete HOST system (blackscreen, bios...) If I install a Windows XP on it it works well on "binary translation" mode. If I try installing Linux on it, in "binary translation" mode it crashes 1 or 2 seconds after I hit enter on the GRUB selection screen (after the first page of kernel messages rolled in) Using VirtualBox it crashes right in the BIOS. It gave me a Bluescreen though! 0x00000101: CLOCK_WATCHDOG_TIMEOUT: a clock interrupt was not received on a secondary processor within the allocated time interval NEWS: I tried VirtualBox again and it did not completely crash the computer this time. It gave me a critical error and a log file: http://pastebin.com/yKZSDs91 In conclusion, it will crash instantly if VT-x is activated. If not, it seemingly only crashed if I try to install something with 64 bits. Another update: Yes, it ONLY crashes when the guest is 64 bit! What I tried: Reinstalling Windows (my Windows installation was quite broken so it seemed natural. Didn't work though.) New BIOS What I am certain of: Virtualization extensions are activated in the BIOS What my computer specs are: ASUS P8P67 LE mainboard, newest BIOS/EFI firmware Intel Core i5 2500k Ati Radeon HD 5770 16 GB Corsair 1333mhz DDR3 RAM, 4 X 4 GB

    Read the article

  • Why is my rsync so slow compared to pure cp or even scp?

    - by nfm
    I'm transfering the files from Linux to Windows 7 via a mounted share (the share is mounted from Windows on Linux).. I'm copying lots of data (i.e. nearly a TB) from the old to the new machine within my LAN. I'm unfortunate enough already that I only have 100MBit. Naturally I blindly used rsync but already wondered after a day why it feels so slow. Enabling the progress meter showed my a transfer rate of about 2MBit/s . So I took a reasonable big file (800MB) and tracked the transfer timing: cp : 05:33 scp (*): 06:33 rsync : 21:51 *) scp via localhost to the same Linux machine directly onto the share; completely useless but provided a progress meter The tests were as simple as (cp|scp|rsync) <source> <destination> No special arguments except host/port for scp. I even tried the -W switch for rsync but cancelled after ten minutes. rsync is 3.0.3 running on Lenny. To be able to interrupt the copy process anytime and resume lead me to rsync, but now I think I seriously need to reconsider this requirement. How's such a big difference possible?

    Read the article

  • Route web traffic through a separate iterface

    - by tkane
    I'd like to route web traffic through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

    Read the article

  • Computer won't start up. Stuck on Lenovo splash screen. Help Diagnose

    - by Ace Legend
    I have some (I'm not sure exactly what model) Lenovo 21" IdeaCentre. Honestly, the computer works off and on. I have had problems with it not being able to shutdown, which I fixed. The fan seems to be constantly running, a few other problems as well. Anyway, nobody was using it when all of a sudden it switched to a blue screen. I was in the kitchen, but when I got over to the computer I read the message. It said something about bad drivers, but that is all I saw and then it restarted. However, when it got to the Lenovo Splash screen, nothing happened. I waited there for over 10 minutes, but still nothing. I tried to turn of the computer, but the only way to do it was to pull out the power cable. I then removed all USB devices and tried again. Still nothing. It also won't respond to keyboard input when I try to use enter to interrupt normal startup. My guess is some piece of hardware is damaged inside the machine. However, I have no idea what piece it is. Does anybody have any idea what could be wrong with it? Thanks.

    Read the article

  • SSH Connection Error : No route to host

    - by dewbot
    There are three machines in this scenario: Desktop A : [email protected] Laptop A : [email protected] Machine B : [email protected] All the machines have Ubuntu 11.04 (Desktop A is a 64bit one) and have both openssh-server and openssh-client. Now when I try to connect Desktop A to Laptop A or vice-versa by ssh [email protected] I get an error as port 22: No route to host in both the cases. I own both the machines, now if I try same commands from my friend's machine, i.e. via Desktop B, I can access both my Laptop and Desktop. But if I try to access Desktop B from my Laptop or by Desktop I get port 22: Connection timed out I even tried changing ssh port no. in ssh_config file but no success. Note: that 'Laptop A' uses WiFi connection while 'Machine A' uses Ethernet Connection and 'Machine B' is on an entirely different network. Laptop A && Desktop A - Router/Nano_Rcvr provided to me by ISP. So to one Router two Machines are connected and can be accessed at the same time. here is my ifconfig output for both the machines :- Laptop wlan0 Link encap:Ethernet HWaddr X:X:X:X:00:bc inet addr:1.23.73.111 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::219:e3ff:fe04:bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108409 errors:0 dropped:0 overruns:0 frame:0 TX packets:82523 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44974080 (44.9 MB) TX bytes:22973031 (22.9 MB) Desktop eth0 Link encap:Ethernet HWaddr X:X:X:X:c5:78 inet addr:1.23.68.209 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::227:eff:fe04:c578/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10380 errors:0 dropped:0 overruns:0 frame:0 TX packets:4509 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1790366 (1.7 MB) TX bytes:852877 (852.8 KB) Interrupt:43 Base address:0x2000

    Read the article

  • Route web browsing through a separate iterface

    - by tkane
    I'd like to route web browsing through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

    Read the article

  • Libvirt/KVM in NAT: can't access from host (and can't forward)

    - by SharkWipf
    I'm trying to set up a port forward to a KVM guest, managed through Libvirt on Debian 6. The VM is running in NAT, through the "default" network. This all runs fine, the VM has full internet connection. However, the host cannot reach the vm internally. Neither ping, nc nor nmap on the NAT network give any signs of the VM. Due to this, the normal iptables forwarding rules don't work either. $ cat /etc/debian_version 6.0.5 $ libvirtd --version libvirtd (libvirt) 0.9.11.3 $ kvm --version QEMU emulator version 1.0 (qemu-kvm-1.0+dfsg-11, Debian), Copyright (c) 2003-2008 Fabrice Bellard ifconfig: eth0 Link encap:Ethernet HWaddr 54:04:a6:f1:6f:10 inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.x inet6 addr: fe80::5604:a6ff:fef1:6f10/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118902 errors:0 dropped:0 overruns:0 frame:0 TX packets:142357 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:13247173 (12.6 MiB) TX bytes:95163190 (90.7 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:230646 errors:0 dropped:0 overruns:0 frame:0 TX packets:230646 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204577107 (195.0 MiB) TX bytes:204577107 (195.0 MiB) virbr0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:666759 (651.1 KiB) TX bytes:400701 (391.3 KiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet6 addr: fe80::fc54:ff:fee2:d260/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:125687 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:739803 (722.4 KiB) TX bytes:6886609 (6.5 MiB)

    Read the article

  • Apache using 100% CPU, once again

    - by CBenni
    Recently, apache2 started using 100% of CPU power: top gives me From other, similar threads, I took the tip to use mod_status. Aside from HUGE amounts of NULL requests, it gives: CPU Usage: u2.16 s1.32 cu0 cs0 - .0835% CPU load 1.2 requests/sec - 17.6 kB/second - 14.6 kB/request 8 requests currently being processed, 42 idle workers The access and error logs do not show anything surprising or intriguing at all. Note the .8% CPU usage. Another tip was to use strace: root@server:~# strace -p 1956 Process 1956 attached - interrupt to quit restart_syscall(<... resuming interrupted call ...> And remains like this for at least half an hour, without producing any additional output. Restarting apache fixed the problem for less than a second The server runs a few custom python scripts aswell as a django-powered website on apache2 (up-to-date), but even turning the scripts off (or not having them active in the first place) did not change anything. After I stopped apache and powered my server off, powered it on a few minutes afterwards and restarted all my services, the CPU usage remained low for several hours, just in order to pop up again randomly (?) The DigitalOcean CPU stats on my server are: You can see how the CPU usage was super high for almost half a day until I restarted the bot - just to remain stable for several hours and then pop up again. I am completely at a loss of words and don't know what I could do to find out what piece of my code is giving me these problems or if apache itself is the cause... Therefore I would greatly appreciate any hints to the questions: What else can I try to do? Which things might I not have checked? Is this definitely in my own code? How do you find what part of python code crashes an app via a infinite loop or similar?

    Read the article

  • How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

    - by Todd V. Rovito
    I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

    Read the article

  • how to get ip address of a PPP(Point-to-Point Protocol) network interface?

    - by Xsmael
    I have a Linux machine with two network interfaces, and I'd like to get the IP address of the PPP interface w1g1 but it doesn't show up in ifconfig. There is a public IP on the PPP interface, but there is no internet connection, I'm trying to troubleshoot but I need to get the IP address of the interface and I can't. ifconfig : eth0 Link encap:Ethernet HWaddr 00:30:48:8D:F0:2C inet addr:192.168.2.254 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:fe8d:f02c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:9970 errors:0 dropped:567 overruns:0 frame:0 TX packets:4338 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:1441024 (1.3 MiB) TX bytes:915814 (894.3 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:675 errors:0 dropped:0 overruns:0 frame:0 TX packets:675 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:50659 (49.4 KiB) TX bytes:50659 (49.4 KiB) w1g1 Link encap:Point-to-Point Protocol UP POINTOPOINT RUNNING NOARP MTU:240 Metric:1 RX packets:748994 errors:0 dropped:0 overruns:0 frame:0 TX packets:748992 errors:0 dropped:0 overruns:0 carrier:3 collisions:0 txqueuelen:100 RX bytes:179758560 (171.4 MiB) TX bytes:179758080 (171.4 MiB) Interrupt:177 Memory:f881c400-f881e3ff w1g1 is connected to a modem by an RJ45<-Serial cable and the modem is connected to the phone line. The modem is a NOKIA DNT2Mi you can see it here Routing table : 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.254 169.254.0.0/16 dev eth0 scope link default via 192.168.2.180 dev eth0

    Read the article

  • Server not resolving after restart

    - by DomainSoil
    I restarted our server today, and now cannot for the life of me get anything to resolve... I suspect it has something to do with our routes. I've tried numerous Google results to no avail. Here is as far as I've gotten: [root@www ~]# route -n Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.101 0.0.0.0 255.255.255.255 UH 0 0 0 eth1 0.0.0.0 192.168.1.101 0.0.0.0 UG 0 0 0 eth1 Things you need to know: Our server (CentOS 6.3) runs two virtual machines, one live, and one development. They mirror each other as much as possible, but I can't find where I've went wrong with the live server. The dev server works fine. [root@www ~]# ifconfig eth1 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx inet6 addr: xxxx:xxx:xxxx:xxxx:xxxx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118206 errors:0 dropped:0 overruns:0 frame:0 TX packets:165 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7825749 (7.4 Mib) TX bytes:7146 (69.2 KiB) Interrupt:28 [root@www ~]# /etc/init.d/network status Configured devices: lo Auto eth0 Currently active devices: lo eth1 If there is any other information you need, please don't hesitate to ask!

    Read the article

  • How to continue an HTTrack mirroring session from the command line?

    - by isme
    I want to drive my mirroring project using the Command Prompt instead of the WinHTTrack interface so that I can script and schedule the mirroring session more easily. The output of httrack --help gives a simple command for continuing an interrupted mirroring session: example: httrack --continue continues a mirror in the current folder When I try httrack --continue in my HTTrack project folder, all I get is output like this: Example: -%F "<!-- Mirrored from %s by HTTrack Website Copier/3.x [XR&CO'2010], %s -->" * Option %F needs to be followed by a blank space, and a footer string With each parameter on a new line for readability, the first line of my doit.log file looks like this: -qiC1%P0s0b0u1j0%s%u0N0%I0p1DaK0c1T30H0%kf2E1800A25000%c0.1%f#f -F "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.0)" -%F "" -%l "en, en, *" http://saa.gov.uk/search.php?SEARCHED=1&SEARCH_TABLE=council_tax&SEARCH_TERM=City+of+Edinburgh&DISPLAY_COUNT=100 -O1 "C:\\Users\\Iain\\Projects\\Council Tax Analysis\\Code\\HTTrack\\Council Tax Valuation List" -* \ +*search.php?SEARCHED=1* -*DISPLAY_MODE=FULL* The parameter %F "" should tell HTTrack to use an empty footer. I used the WinHTTrack interface to create the project and start the mirroring session. I can interrupt and continue the mirroring session using the interface. The HTML files saved by WinHTTrack have no footer.

    Read the article

  • Sound doesn't work anymore after replacing RAM

    - by thejh
    Hello, today, I replaced one old RAM module with two newer, bigger ones, but now, the sound doesn't seem to work anymore. Already ran alsaconf and it didn't help. Output of lspci for the audio device: 00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1) Subsystem: Giga-byte Technology Device a002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at f5100000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel The audio device is onboard and has six configurable outputs, two or so are also capable of being an input (if I remember it correctly), but I don't know how to control it under linux. Does somebody know how/whether replacing the RAM could be related to my problem and/or how to fix it?

    Read the article

  • What is the fall off of subsecond throughput on Ethernet Network Interfaces

    - by Kyle Brandt
    On a network interface, speeds are given in term of data over time, in particular, they are bits per second. However, in the uber-fast world of computing -- a second is kind of a really long time. So for example, given a linear falloff. A 1 GBit per second interface would do 500MBit per half second, 250Mbit per quarter second etc. I imagine at certain units of time, this is no longer linear. Perhaps this is set by ethernet frequencies, system clock speeds, interrupt timers etc. I am sure this varies depending on the system -- but does anyone have more information or whitepapers on this? One of the main reasons I am curious is to understand output drops on interfaces. Even if the speed per second is much lower than the interface can handle -- perhaps there are spikes that cause drops for only small numbers of milliseconds. Perhaps various coalescing would hide this effect -- or perhaps increase it on the receiving interface? Do queues make a difference here? Example: So given if this is linear down to the MS we would have 1Mbit/MS, and if Wireshark isn't distorting what I see, should I see drops when I have a spike beyond 1Mbit?

    Read the article

  • Looking for a nice and handy bandwidth limiter

    - by Spirit
    Here's the thing. My ISP are f*gs. Most of the time the network is realy good, but then again there are times when it sucks. They say we have 20mbp/s. Me and my brother are usually playing dota and it's fine. One of us plays the other's watching streaming or both of us are playing or something like that. But sometimes like one of these days one is lagging even if the other is watching youtube at 360p quality. So I do know that there are many bandwidth limiters out there. But what could you recommend given my situation. I like both of us to be able to install it and it would be good idea to have something like ON/OFF switch. When he is not here I would like to turn that thing off. But when one of us plays I would like to turn it ON and whatever I do, to be limited to 10 or 8mbps. That way we will not interrupt each other. Thanks guys :)

    Read the article

  • FreeBSD performance tuning. Sysctls, loader.conf, kernel

    - by SaveTheRbtz
    I wanted to share knowledge of tuning FreeBSD via sysctl.conf/loader.conf/KENCONF. It was initially based on Igor Sysoev's (author of nginx) presentation about FreeBSD tuning up to 100,000-200,000 active connections. Tunings are for FreeBSD-CURRENT. Since 7.2 amd64 some of them are tuned well by default. Prior 7.0 some of them are boot only (set via /boot/loader.conf) or does not exist at all. sysctl.conf: # No zero mapping feature # May break wine # (There are also reports about broken samba3) #security.bsd.map_at_zero=0 # If you have really busy webserver with apache13 you may run out of processes #kern.maxproc=10000 # Same for servers with apache2 / Pound #kern.threads.max_threads_per_proc=4096 # Max. backlog size kern.ipc.somaxconn=4096 # Shared memory // 7.2+ can use shared memory > 2Gb kern.ipc.shmmax=2147483648 # Sockets kern.ipc.maxsockets=204800 # Can cause this on older kernels: # http://old.nabble.com/Significant-performance-regression-for-increased-maxsockbuf-on-8.0-RELEASE-tt26745981.html#a26745981 ) kern.ipc.maxsockbuf=10485760 # Mbuf 2k clusters (on amd64 7.2+ 25600 is default) # For such high value vm.kmem_size must be increased to 3G kern.ipc.nmbclusters=262144 # Jumbo pagesize(_SC_PAGESIZE) clusters # Used as general packet storage for jumbo frames # can be monitored via `netstat -m` #kern.ipc.nmbjumbop=262144 # Jumbo 9k/16k clusters # If you are using them #kern.ipc.nmbjumbo9=65536 #kern.ipc.nmbjumbo16=32768 # For lower latency you can decrease scheduler's maximum time slice # default: stathz/10 (~ 13) #kern.sched.slice=1 # Increase max command-line length showed in `ps` (e.g for Tomcat/Java) # Default is PAGE_SIZE / 16 or 256 on x86 # This avoids commands to be presented as [executable] in `ps` # For more info see: http://www.freebsd.org/cgi/query-pr.cgi?pr=120749 kern.ps_arg_cache_limit=4096 # Every socket is a file, so increase them kern.maxfiles=204800 kern.maxfilesperproc=200000 kern.maxvnodes=200000 # On some systems HPET is almost 2 times faster than default ACPI-fast # Useful on systems with lots of clock_gettime / gettimeofday calls # See http://old.nabble.com/ACPI-fast-default-timecounter,-but-HPET-83--faster-td23248172.html # After revision 222222 HPET became default: http://svnweb.freebsd.org/base?view=revision&revision=222222 kern.timecounter.hardware=HPET # Small receive space, only usable on http-server, on file server this # should be increased to 65535 or even more #net.inet.tcp.recvspace=8192 # This is useful on Fat-Long-Pipes #net.inet.tcp.recvbuf_max=10485760 #net.inet.tcp.recvbuf_inc=65535 # Small send space is useful for http servers that serve small files # Autotuned since 7.x net.inet.tcp.sendspace=16384 # This is useful on Fat-Long-Pipes #net.inet.tcp.sendbuf_max=10485760 #net.inet.tcp.sendbuf_inc=65535 # Turn off receive autotuning # You can play with it. #net.inet.tcp.recvbuf_auto=0 #net.inet.tcp.sendbuf_auto=0 # This should be enabled if you going to use big spaces (>64k) # Also timestamp field is useful when using syncookies net.inet.tcp.rfc1323=1 # Turn this off on high-speed, lossless connections (LAN 1Gbit+) # If you set it there is no need in TCP_NODELAY sockopt (see man tcp) net.inet.tcp.delayed_ack=0 # This feature is useful if you are serving data over modems, Gigabit Ethernet, # or even high speed WAN links (or any other link with a high bandwidth delay product), # especially if you are also using window scaling or have configured a large send window. # Automatically disables on small RTT ( http://www.freebsd.org/cgi/cvsweb.cgi/src/sys/netinet/tcp_subr.c?#rev1.237 ) # This sysctl was removed in 10-CURRENT: # See: http://www.mail-archive.com/[email protected]/msg06178.html #net.inet.tcp.inflight.enable=0 # TCP slowstart algorithm tunings # We assuming we have very fast clients #net.inet.tcp.slowstart_flightsize=100 #net.inet.tcp.local_slowstart_flightsize=100 # Disable randomizing of ports to avoid false RST # Before usage check SA here www.bsdcan.org/2006/papers/ImprovingTCPIP.pdf # (it's also says that port randomization auto-disables at some conn.rates, but I didn't checked it thou) #net.inet.ip.portrange.randomized=0 # Increase portrange # For outgoing connections only. Good for seed-boxes and ftp servers. net.inet.ip.portrange.first=1024 net.inet.ip.portrange.last=65535 # # stops route cache degregation during a high-bandwidth flood # http://www.freebsd.org/doc/en/books/handbook/securing-freebsd.html #net.inet.ip.rtexpire=2 net.inet.ip.rtminexpire=2 net.inet.ip.rtmaxcache=1024 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # # There is also good example of sysctl.conf with comments: # http://www.thern.org/projects/sysctl.conf # # icmp may NOT rst, helpful for those pesky spoofed # icmp/udp floods that end up taking up your outgoing # bandwidth/ifqueue due to all that outgoing RST traffic. # #net.inet.tcp.icmp_may_rst=0 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # IPv6 Security # For more info see http://www.fosslc.org/drupal/content/security-implications-ipv6 # Disable Node info replies # To see this vulnerability in action run `ping6 -a sglAac ::1` or `ping6 -w ::1` on unprotected node net.inet6.icmp6.nodeinfo=0 # Turn on IPv6 privacy extensions # For more info see proposal http://unix.derkeiler.com/Mailing-Lists/FreeBSD/net/2008-06/msg00103.html net.inet6.ip6.use_tempaddr=1 net.inet6.ip6.prefer_tempaddr=1 # Disable ICMP redirect net.inet6.icmp6.rediraccept=0 # Disable acceptation of RA and auto linklocal generation if you don't use them #net.inet6.ip6.accept_rtadv=0 #net.inet6.ip6.auto_linklocal=0 # Increases default TTL, sometimes useful # Default is 64 net.inet.ip.ttl=128 # Lessen max segment life to conserve resources # ACK waiting time in miliseconds # (default: 30000. RFC from 1979 recommends 120000) net.inet.tcp.msl=5000 # Max bumber of timewait sockets net.inet.tcp.maxtcptw=200000 # Don't use tw on local connections # As of 15 Apr 2009. Igor Sysoev says that nolocaltimewait has some buggy realization. # So disable it or now till get fixed #net.inet.tcp.nolocaltimewait=1 # FIN_WAIT_2 state fast recycle net.inet.tcp.fast_finwait2_recycle=1 # Time before tcp keepalive probe is sent # default is 2 hours (7200000) #net.inet.tcp.keepidle=60000 # Should be increased until net.inet.ip.intr_queue_drops is zero net.inet.ip.intr_queue_maxlen=4096 # Interrupt handling via multiple CPU, but with context switch. # You can play with it. Default is 1; #net.isr.direct=0 # This is for routers only #net.inet.ip.forwarding=1 #net.inet.ip.fastforwarding=1 # This speed ups dummynet when channel isn't saturated net.inet.ip.dummynet.io_fast=1 # Increase dummynet(4) hash #net.inet.ip.dummynet.hash_size=2048 #net.inet.ip.dummynet.max_chain_len # Should be increased when you have A LOT of files on server # (Increase until vfs.ufs.dirhash_mem becomes lower) vfs.ufs.dirhash_maxmem=67108864 # Note from commit http://svn.freebsd.org/base/head@211031 : # For systems with RAID volumes and/or virtualization envirnments, where # read performance is very important, increasing this sysctl tunable to 32 # or even more will demonstratively yield additional performance benefits. vfs.read_max=32 # Explicit Congestion Notification (see http://en.wikipedia.org/wiki/Explicit_Congestion_Notification) net.inet.tcp.ecn.enable=1 # Flowtable - flow caching mechanism # Useful for routers #net.inet.flowtable.enable=1 #net.inet.flowtable.nmbflows=65535 # Extreme polling tuning #kern.polling.burst_max=1000 #kern.polling.each_burst=1000 #kern.polling.reg_frac=100 #kern.polling.user_frac=1 #kern.polling.idle_poll=0 # IPFW dynamic rules and timeouts tuning # Increase dyn_buckets till net.inet.ip.fw.curr_dyn_buckets is lower net.inet.ip.fw.dyn_buckets=65536 net.inet.ip.fw.dyn_max=65536 net.inet.ip.fw.dyn_ack_lifetime=120 net.inet.ip.fw.dyn_syn_lifetime=10 net.inet.ip.fw.dyn_fin_lifetime=2 net.inet.ip.fw.dyn_short_lifetime=10 # Make packets pass firewall only once when using dummynet # i.e. packets going thru pipe are passing out from firewall with accept #net.inet.ip.fw.one_pass=1 # shm_use_phys Wires all shared pages, making them unswappable # Use this to lessen Virtual Memory Manager's work when using Shared Mem. # Useful for databases #kern.ipc.shm_use_phys=1 # ZFS # Enable prefetch. Useful for sequential load type i.e fileserver. # FreeBSD sets vfs.zfs.prefetch_disable to 1 on any i386 systems and # on any amd64 systems with less than 4GB of avaiable memory # For additional info check this nabble thread http://old.nabble.com/Samba-read-speed-performance-tuning-td27964534.html #vfs.zfs.prefetch_disable=0 # On highload servers you may notice following message in dmesg: # "Approaching the limit on PV entries, consider increasing either the # vm.pmap.shpgperproc or the vm.pmap.pv_entry_max tunable" vm.pmap.shpgperproc=2048 loader.conf: # Accept filters for data, http and DNS requests # Useful when your software uses select() instead of kevent/kqueue or when you under DDoS # DNS accf available on 8.0+ accf_data_load="YES" accf_http_load="YES" accf_dns_load="YES" # Async IO system calls aio_load="YES" # Linux specific devices in /dev # As for 8.1 it only /dev/full #lindev_load="YES" # Adds NCQ support in FreeBSD # WARNING! all ad[0-9]+ devices will be renamed to ada[0-9]+ # 8.0+ only #ahci_load="YES" #siis_load="YES" # FreeBSD 8.2+ # New Congestion Control for FreeBSD # http://caia.swin.edu.au/urp/newtcp/tools/cc_chd-readme-0.1.txt # http://www.ietf.org/proceedings/78/slides/iccrg-5.pdf # Initial merge commit message http://www.mail-archive.com/[email protected]/msg31410.html #cc_chd_load="YES" # Increase kernel memory size to 3G. # # Use ONLY if you have KVA_PAGES in kernel configuration, and you have more than 3G RAM # Otherwise panic will happen on next reboot! # # It's required for high buffer sizes: kern.ipc.nmbjumbop, kern.ipc.nmbclusters, etc # Useful on highload stateful firewalls, proxies or ZFS fileservers # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #vm.kmem_size="3G" # If your server has lots of swap (>4Gb) you should increase following value # according to http://lists.freebsd.org/pipermail/freebsd-hackers/2009-October/029616.html # Otherwise you'll be getting errors # "kernel: swap zone exhausted, increase kern.maxswzone" # kern.maxswzone="256M" # Older versions of FreeBSD can't tune maxfiles on the fly #kern.maxfiles="200000" # Useful for databases # Sets maximum data size to 1G # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #kern.maxdsiz="1G" # Maximum buffer size(vfs.maxbufspace) # You can check current one via vfs.bufspace # Should be lowered/upped depending on server's load-type # Usually decreased to preserve kmem # (default is 10% of mem) #kern.maxbcache="512M" # Sendfile buffers # For i386 only #kern.ipc.nsfbufs=10240 # FreeBSD 9+ # HPET "legacy route" support. It should allow HPET to work per-CPU # See http://www.mail-archive.com/[email protected]/msg03603.html #hint.atrtc.0.clock=0 #hint.attimer.0.clock=0 #hint.hpet.0.legacy_route=1 # syncache Hash table tuning net.inet.tcp.syncache.hashsize=1024 net.inet.tcp.syncache.bucketlimit=512 net.inet.tcp.syncache.cachelimit=65536 # Increased hostcache # Later host cache can be viewed via net.inet.tcp.hostcache.list hidden sysctl # Very useful for it's RTT RTTVAR # Must be power of two net.inet.tcp.hostcache.hashsize=65536 # hashsize * bucketlimit (which is 30 by default) # It allocates 255Mb (1966080*136) of RAM net.inet.tcp.hostcache.cachelimit=1966080 # TCP control-block Hash table tuning net.inet.tcp.tcbhashsize=4096 # Disable ipfw deny all # Should be uncommented when there is a chance that # kernel and ipfw binary may be out-of sync on next reboot #net.inet.ip.fw.default_to_accept=1 # # SIFTR (Statistical Information For TCP Research) is a kernel module that # logs a range of statistics on active TCP connections to a log file. # See prerelease notes http://groups.google.com/group/mailing.freebsd.current/browse_thread/thread/b4c18be6cdce76e4 # and man 4 sitfr #siftr_load="YES" # Enable superpages, for 7.2+ only # Also read http://lists.freebsd.org/pipermail/freebsd-hackers/2009-November/030094.html vm.pmap.pg_ps_enabled=1 # Usefull if you are using Intel-Gigabit NIC #hw.em.rxd=4096 #hw.em.txd=4096 #hw.em.rx_process_limit="-1" # Also if you have ALOT interrupts on NIC - play with following parameters # NOTE: You should set them for every NIC #dev.em.0.rx_int_delay: 250 #dev.em.0.tx_int_delay: 250 #dev.em.0.rx_abs_int_delay: 250 #dev.em.0.tx_abs_int_delay: 250 # There is also multithreaded version of em/igb drivers can be found here: # http://people.yandex-team.ru/~wawa/ # # for additional em monitoring and statistics use # sysctl dev.em.0.stats=1 ; dmesg # sysctl dev.em.0.debug=1 ; dmesg # Also after r209242 (-CURRENT) there is a separate sysctl for each stat variable; # Same tunings for igb #hw.igb.rxd=4096 #hw.igb.txd=4096 #hw.igb.rx_process_limit=100 # Some useful netisr tunables. See sysctl net.isr #net.isr.maxthreads=4 #net.isr.defaultqlimit=4096 #net.isr.maxqlimit: 10240 # Bind netisr threads to CPUs #net.isr.bindthreads=1 # # FreeBSD 9.x+ # Increase interface send queue length # See commit message http://svn.freebsd.org/viewvc/base?view=revision&revision=207554 #net.link.ifqmaxlen=1024 # Nicer boot logo =) loader_logo="beastie" And finally here is KERNCONF: # Just some of them, see also # cat /sys/{i386,amd64,}/conf/NOTES # This one useful only on i386 #options KVA_PAGES=512 # You can play with HZ in environments with high interrupt rate (default is 1000) # 100 is for my notebook to prolong it's battery life #options HZ=100 # Polling is goot on network loads with high packet rates and low-end NICs # NB! Do not enable it if you want more than one netisr thread #options DEVICE_POLLING # Eliminate datacopy on socket read-write # To take advantage with zero copy sockets you should have an MTU >= 4k # This req. is only for receiving data. # Read more in man zero_copy_sockets # Also this epic thread on kernel trap: # http://kerneltrap.org/node/6506 # Here Linus says that "anybody that does it that way (FreeBSD) is totally incompetent" #options ZERO_COPY_SOCKETS # Support TCP sign. Used for IPSec options TCP_SIGNATURE # There was stackoverflow found in KAME IPSec stack: # See http://secunia.com/advisories/43995/ # For quick workaround you can use `ipfw add deny proto ipcomp` options IPSEC # This ones can be loaded as modules. They described in loader.conf section #options ACCEPT_FILTER_DATA #options ACCEPT_FILTER_HTTP # Adding ipfw, also can be loaded as modules options IPFIREWALL # On 8.1+ you can disable verbose to see blocked packets on ipfw0 interface. # Also there is no point in compiling verbose into the kernel, because # now there is net.inet.ip.fw.verbose tunable. #options IPFIREWALL_VERBOSE #options IPFIREWALL_VERBOSE_LIMIT=10 options IPFIREWALL_FORWARD # Adding kernel NAT options IPFIREWALL_NAT options LIBALIAS # Traffic shaping options DUMMYNET # Divert, i.e. for userspace NAT options IPDIVERT # This is for OpenBSD's pf firewall device pf device pflog # pf's QoS - ALTQ options ALTQ options ALTQ_CBQ # Class Bases Queuing (CBQ) options ALTQ_RED # Random Early Detection (RED) options ALTQ_RIO # RED In/Out options ALTQ_HFSC # Hierarchical Packet Scheduler (HFSC) options ALTQ_PRIQ # Priority Queuing (PRIQ) options ALTQ_NOPCC # Required for SMP build # Pretty console # Manual can be found here http://forums.freebsd.org/showthread.php?t=6134 #options VESA #options SC_PIXEL_MODE # Disable reboot on Ctrl Alt Del #options SC_DISABLE_REBOOT # Change normal|kernel messages color options SC_NORM_ATTR=(FG_GREEN|BG_BLACK) options SC_KERNEL_CONS_ATTR=(FG_YELLOW|BG_BLACK) # More scroll space options SC_HISTORY_SIZE=8192 # Adding hardware crypto device device crypto device cryptodev # Useful network interfaces device vlan device tap #Virtual Ethernet driver device gre #IP over IP tunneling device if_bridge #Bridge interface device pfsync #synchronization interface for PF device carp #Common Address Redundancy Protocol device enc #IPsec interface device lagg #Link aggregation interface device stf #IPv4-IPv6 port # Also for my notebook, but may be used with Opteron device amdtemp # Same for Intel processors device coretemp # man 4 cpuctl device cpuctl # CPU control pseudo-device # Support for ECMP. More than one route for destination # Works even with default route so one can use it as LB for two ISP # For now code is unstable and panics (panic: rtfree 2) on route deletions. #options RADIX_MPATH # Multicast routing #options MROUTING #options PIM # Debug & DTrace options KDB # Kernel debugger related code options KDB_TRACE # Print a stack trace for a panic options KDTRACE_FRAME # amd64-only(?) options KDTRACE_HOOKS # all architectures - enable general DTrace hooks #options DDB #options DDB_CTF # all architectures - kernel ELF linker loads CTF data # Adaptive spining in lockmgr (8.x+) # See http://www.mail-archive.com/[email protected]/msg10782.html options ADAPTIVE_LOCKMGRS # UTF-8 in console (8.x+) #options TEKEN_UTF8 # FreeBSD 8.1+ # Deadlock resolver thread # For additional information see http://www.mail-archive.com/[email protected]/msg18124.html # (FYI: "resolution" is panic so use with caution) #options DEADLKRES # Increase maximum size of Raw I/O and sendfile(2) readahead #options MAXPHYS=(1024*1024) #options MAXBSIZE=(1024*1024) # For scheduler debug enable following option. # Debug will be available via `kern.sched.stats` sysctl # For more information see http://svnweb.freebsd.org/base/head/sys/conf/NOTES?view=markup #options SCHED_STATS If you are tuning network for maximum performance you may wish to play with ifconfig options like: # You can list all capabilities via `ifconfig -m` ifconfig [-]rxcsum [-]txcsum [-]tso [-]lro mtu In case you've enabled DDB in kernel config, you should edit your /etc/ddb.conf and add something like this to enable automatic reboot (and textdump as bonus): script kdb.enter.panic=textdump set; capture on; show pcpu; bt; ps; alltrace; capture off; call doadump; reset script kdb.enter.default=textdump set; capture on; bt; ps; capture off; call doadump; reset And do not forget to add ddb_enable="YES" to /etc/rc.conf Since FreeBSD 9 you can select to enable/disable flowcontrol on your NIC: # See http://en.wikipedia.org/wiki/Ethernet_flow_control and # http://www.mail-archive.com/[email protected]/msg07927.html for additional info ifconfig bge0 media auto mediaopt flowcontrol PS. Also most of FreeBSD's limits can be monitored by # vmstat -z and # limits PPS. variety of network counters can be monitored via # netstat -s In FreeBSD-9 netstat's -Q option appeared, try following command to display netisr stats # netstat -Q PPPS. also see # man 7 tuning PPPPS. I wanted to thank FreeBSD community, especially author of nginx - Igor Sysoev, nginx-ru@ and FreeBSD-performance@ mailing lists for providing useful information about FreeBSD tuning. FreeBSD WIP * Whats cooking for FreeBSD 7? * Whats cooking for FreeBSD 8? * Whats cooking for FreeBSD 9? So here is the question: What tunings are you using on yours FreeBSD servers? You can also post your /etc/sysctl.conf, /boot/loader.conf, kernel options, etc with description of its' meaning (do not copy-paste from sysctl -d). Don't forget to specify server type (web, smb, gateway, etc) Let's share experience!

    Read the article

  • LSI 9285-8e and Supermicro SC837E26-RJBOD1 duplicate enclosure ID and slot numbers

    - by Andy Shinn
    I am working with 2 x Supermicro SC837E26-RJBOD1 chassis connected to a single LSI 9285-8e card in a Supermicro 1U host. There are 28 drives in each chassis for a total of 56 drives in 28 RAID1 mirrors. The problem I am running in to is that there are duplicate slots for the 2 chassis (the slots list twice and only go from 0 to 27). All the drives also show the same enclosure ID (ID 36). However, MegaCLI -encinfo lists the 2 enclosures correctly (ID 36 and ID 65). My question is, why would this happen? Is there an option I am missing to use 2 enclosures effectively? This is blocking me rebuilding a drive that failed in slot 11 since I can only specify enclosure and slot as parameters to replace a drive. When I do this, it picks the wrong slot 11 (device ID 46 instead of device ID 19). Adapter #1 is the LSI 9285-8e, adapter #0 (which I removed due to space limitations) is the onboard LSI. Adapter information: Adapter #1 ============================================================================== Versions ================ Product Name : LSI MegaRAID SAS 9285-8e Serial No : SV12704804 FW Package Build: 23.1.1-0004 Mfg. Data ================ Mfg. Date : 06/30/11 Rework Date : 00/00/00 Revision No : 00A Battery FRU : N/A Image Versions in Flash: ================ BIOS Version : 5.25.00_4.11.05.00_0x05040000 WebBIOS Version : 6.1-20-e_20-Rel Preboot CLI Version: 05.01-04:#%00001 FW Version : 3.140.15-1320 NVDATA Version : 2.1106.03-0051 Boot Block Version : 2.04.00.00-0001 BOOT Version : 06.253.57.219 Pending Images in Flash ================ None PCI Info ================ Vendor Id : 1000 Device Id : 005b SubVendorId : 1000 SubDeviceId : 9285 Host Interface : PCIE ChipRevision : B0 Number of Frontend Port: 0 Device Interface : PCIE Number of Backend Port: 8 Port : Address 0 5003048000ee8e7f 1 5003048000ee8a7f 2 0000000000000000 3 0000000000000000 4 0000000000000000 5 0000000000000000 6 0000000000000000 7 0000000000000000 HW Configuration ================ SAS Address : 500605b0038f9210 BBU : Present Alarm : Present NVRAM : Present Serial Debugger : Present Memory : Present Flash : Present Memory Size : 1024MB TPM : Absent On board Expander: Absent Upgrade Key : Absent Temperature sensor for ROC : Present Temperature sensor for controller : Absent ROC temperature : 70 degree Celcius Settings ================ Current Time : 18:24:36 3/13, 2012 Predictive Fail Poll Interval : 300sec Interrupt Throttle Active Count : 16 Interrupt Throttle Completion : 50us Rebuild Rate : 30% PR Rate : 30% BGI Rate : 30% Check Consistency Rate : 30% Reconstruction Rate : 30% Cache Flush Interval : 4s Max Drives to Spinup at One Time : 2 Delay Among Spinup Groups : 12s Physical Drive Coercion Mode : Disabled Cluster Mode : Disabled Alarm : Enabled Auto Rebuild : Enabled Battery Warning : Enabled Ecc Bucket Size : 15 Ecc Bucket Leak Rate : 1440 Minutes Restore HotSpare on Insertion : Disabled Expose Enclosure Devices : Enabled Maintain PD Fail History : Enabled Host Request Reordering : Enabled Auto Detect BackPlane Enabled : SGPIO/i2c SEP Load Balance Mode : Auto Use FDE Only : No Security Key Assigned : No Security Key Failed : No Security Key Not Backedup : No Default LD PowerSave Policy : Controller Defined Maximum number of direct attached drives to spin up in 1 min : 10 Any Offline VD Cache Preserved : No Allow Boot with Preserved Cache : No Disable Online Controller Reset : No PFK in NVRAM : No Use disk activity for locate : No Capabilities ================ RAID Level Supported : RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, PRL 11 with spanning, SRL 3 supported, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span Supported Drives : SAS, SATA Allowed Mixing: Mix in Enclosure Allowed Mix of SAS/SATA of HDD type in VD Allowed Status ================ ECC Bucket Count : 0 Limitations ================ Max Arms Per VD : 32 Max Spans Per VD : 8 Max Arrays : 128 Max Number of VDs : 64 Max Parallel Commands : 1008 Max SGE Count : 60 Max Data Transfer Size : 8192 sectors Max Strips PerIO : 42 Max LD per array : 16 Min Strip Size : 8 KB Max Strip Size : 1.0 MB Max Configurable CacheCade Size: 0 GB Current Size of CacheCade : 0 GB Current Size of FW Cache : 887 MB Device Present ================ Virtual Drives : 28 Degraded : 0 Offline : 0 Physical Devices : 59 Disks : 56 Critical Disks : 0 Failed Disks : 0 Supported Adapter Operations ================ Rebuild Rate : Yes CC Rate : Yes BGI Rate : Yes Reconstruct Rate : Yes Patrol Read Rate : Yes Alarm Control : Yes Cluster Support : No BBU : No Spanning : Yes Dedicated Hot Spare : Yes Revertible Hot Spares : Yes Foreign Config Import : Yes Self Diagnostic : Yes Allow Mixed Redundancy on Array : No Global Hot Spares : Yes Deny SCSI Passthrough : No Deny SMP Passthrough : No Deny STP Passthrough : No Support Security : No Snapshot Enabled : No Support the OCE without adding drives : Yes Support PFK : Yes Support PI : No Support Boot Time PFK Change : Yes Disable Online PFK Change : No PFK TrailTime Remaining : 0 days 0 hours Support Shield State : Yes Block SSD Write Disk Cache Change: Yes Supported VD Operations ================ Read Policy : Yes Write Policy : Yes IO Policy : Yes Access Policy : Yes Disk Cache Policy : Yes Reconstruction : Yes Deny Locate : No Deny CC : No Allow Ctrl Encryption: No Enable LDBBM : No Support Breakmirror : No Power Savings : Yes Supported PD Operations ================ Force Online : Yes Force Offline : Yes Force Rebuild : Yes Deny Force Failed : No Deny Force Good/Bad : No Deny Missing Replace : No Deny Clear : No Deny Locate : No Support Temperature : Yes Disable Copyback : No Enable JBOD : No Enable Copyback on SMART : No Enable Copyback to SSD on SMART Error : Yes Enable SSD Patrol Read : No PR Correct Unconfigured Areas : Yes Enable Spin Down of UnConfigured Drives : Yes Disable Spin Down of hot spares : No Spin Down time : 30 T10 Power State : Yes Error Counters ================ Memory Correctable Errors : 0 Memory Uncorrectable Errors : 0 Cluster Information ================ Cluster Permitted : No Cluster Active : No Default Settings ================ Phy Polarity : 0 Phy PolaritySplit : 0 Background Rate : 30 Strip Size : 64kB Flush Time : 4 seconds Write Policy : WB Read Policy : Adaptive Cache When BBU Bad : Disabled Cached IO : No SMART Mode : Mode 6 Alarm Disable : Yes Coercion Mode : None ZCR Config : Unknown Dirty LED Shows Drive Activity : No BIOS Continue on Error : No Spin Down Mode : None Allowed Device Type : SAS/SATA Mix Allow Mix in Enclosure : Yes Allow HDD SAS/SATA Mix in VD : Yes Allow SSD SAS/SATA Mix in VD : No Allow HDD/SSD Mix in VD : No Allow SATA in Cluster : No Max Chained Enclosures : 16 Disable Ctrl-R : Yes Enable Web BIOS : Yes Direct PD Mapping : No BIOS Enumerate VDs : Yes Restore Hot Spare on Insertion : No Expose Enclosure Devices : Yes Maintain PD Fail History : Yes Disable Puncturing : No Zero Based Enclosure Enumeration : No PreBoot CLI Enabled : Yes LED Show Drive Activity : Yes Cluster Disable : Yes SAS Disable : No Auto Detect BackPlane Enable : SGPIO/i2c SEP Use FDE Only : No Enable Led Header : No Delay during POST : 0 EnableCrashDump : No Disable Online Controller Reset : No EnableLDBBM : No Un-Certified Hard Disk Drives : Allow Treat Single span R1E as R10 : No Max LD per array : 16 Power Saving option : Don't Auto spin down Configured Drives Max power savings option is not allowed for LDs. Only T10 power conditions are to be used. Default spin down time in minutes: 30 Enable JBOD : No TTY Log In Flash : No Auto Enhanced Import : No BreakMirror RAID Support : No Disable Join Mirror : No Enable Shield State : Yes Time taken to detect CME : 60s Exit Code: 0x00 Enclosure information: # /opt/MegaRAID/MegaCli/MegaCli64 -encinfo -a1 Number of enclosures on adapter 1 -- 3 Enclosure 0: Device ID : 36 Number of Slots : 28 Number of Power Supplies : 2 Number of Fans : 3 Number of Temperature Sensors : 1 Number of Alarms : 1 Number of SIM Modules : 0 Number of Physical Drives : 28 Status : Normal Position : 1 Connector Name : Port B Enclosure type : SES VendorId is LSI CORP and Product Id is SAS2X36 VendorID and Product ID didnt match FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : 65 Inquiry data : Vendor Identification : LSI CORP Product Identification : SAS2X36 Product Revision Level : 0718 Vendor Specific : x36-55.7.24.1 Number of Voltage Sensors :2 Voltage Sensor :0 Voltage Sensor Status :OK Voltage Value :5020 milli volts Voltage Sensor :1 Voltage Sensor Status :OK Voltage Value :11820 milli volts Number of Power Supplies : 2 Power Supply : 0 Power Supply Status : OK Power Supply : 1 Power Supply Status : OK Number of Fans : 3 Fan : 0 Fan Speed :Low Speed Fan Status : OK Fan : 1 Fan Speed :Low Speed Fan Status : OK Fan : 2 Fan Speed :Low Speed Fan Status : OK Number of Temperature Sensors : 1 Temp Sensor : 0 Temperature : 48 Temperature Sensor Status : OK Number of Chassis : 1 Chassis : 0 Chassis Status : OK Enclosure 1: Device ID : 65 Number of Slots : 28 Number of Power Supplies : 2 Number of Fans : 3 Number of Temperature Sensors : 1 Number of Alarms : 1 Number of SIM Modules : 0 Number of Physical Drives : 28 Status : Normal Position : 1 Connector Name : Port A Enclosure type : SES VendorId is LSI CORP and Product Id is SAS2X36 VendorID and Product ID didnt match FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : 36 Inquiry data : Vendor Identification : LSI CORP Product Identification : SAS2X36 Product Revision Level : 0718 Vendor Specific : x36-55.7.24.1 Number of Voltage Sensors :2 Voltage Sensor :0 Voltage Sensor Status :OK Voltage Value :5020 milli volts Voltage Sensor :1 Voltage Sensor Status :OK Voltage Value :11760 milli volts Number of Power Supplies : 2 Power Supply : 0 Power Supply Status : OK Power Supply : 1 Power Supply Status : OK Number of Fans : 3 Fan : 0 Fan Speed :Low Speed Fan Status : OK Fan : 1 Fan Speed :Low Speed Fan Status : OK Fan : 2 Fan Speed :Low Speed Fan Status : OK Number of Temperature Sensors : 1 Temp Sensor : 0 Temperature : 47 Temperature Sensor Status : OK Number of Chassis : 1 Chassis : 0 Chassis Status : OK Enclosure 2: Device ID : 252 Number of Slots : 8 Number of Power Supplies : 0 Number of Fans : 0 Number of Temperature Sensors : 0 Number of Alarms : 0 Number of SIM Modules : 1 Number of Physical Drives : 0 Status : Normal Position : 1 Connector Name : Unavailable Enclosure type : SGPIO Failed in first Inquiry commnad FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : Unavailable Inquiry data : Vendor Identification : LSI Product Identification : SGPIO Product Revision Level : N/A Vendor Specific : Exit Code: 0x00 Now, notice that each slot 11 device shows an enclosure ID of 36, I think this is where the discrepancy happens. One should be 36. But the other should be on enclosure 65. Drives in slot 11: Enclosure Device ID: 36 Slot Number: 11 Drive's postion: DiskGroup: 5, Span: 0, Arm: 1 Enclosure position: 0 Device Id: 48 WWN: Sequence Number: 11 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 2.728 TB [0x15d50a3b0 Sectors] Non Coerced Size: 2.728 TB [0x15d40a3b0 Sectors] Coerced Size: 2.728 TB [0x15d400000 Sectors] Firmware state: Online, Spun Up Is Commissioned Spare : YES Device Firmware Level: A5C0 Shield Counter: 0 Successful diagnostics completion on : N/A SAS Address(0): 0x5003048000ee8a53 Connected Port Number: 1(path0) Inquiry Data: MJ1311YNG6YYXAHitachi HDS5C3030ALA630 MEAOA5C0 FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive Temperature :30C (86.00 F) PI Eligibility: No Drive is formatted for PI information: No PI: No PI Drive's write cache : Disabled Drive's NCQ setting : Enabled Port-0 : Port status: Active Port's Linkspeed: 6.0Gb/s Drive has flagged a S.M.A.R.T alert : No Enclosure Device ID: 36 Slot Number: 11 Drive's postion: DiskGroup: 19, Span: 0, Arm: 1 Enclosure position: 0 Device Id: 19 WWN: Sequence Number: 4 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 2.728 TB [0x15d50a3b0 Sectors] Non Coerced Size: 2.728 TB [0x15d40a3b0 Sectors] Coerced Size: 2.728 TB [0x15d400000 Sectors] Firmware state: Online, Spun Up Is Commissioned Spare : NO Device Firmware Level: A580 Shield Counter: 0 Successful diagnostics completion on : N/A SAS Address(0): 0x5003048000ee8e53 Connected Port Number: 0(path0) Inquiry Data: MJ1313YNG1VA5CHitachi HDS5C3030ALA630 MEAOA580 FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive Temperature :30C (86.00 F) PI Eligibility: No Drive is formatted for PI information: No PI: No PI Drive's write cache : Disabled Drive's NCQ setting : Enabled Port-0 : Port status: Active Port's Linkspeed: 6.0Gb/s Drive has flagged a S.M.A.R.T alert : No Update 06/28/12: I finally have some new information about (what we think) the root cause of this problem so I thought I would share. After getting in contact with a very knowledgeable Supermicro tech, they provided us with a tool called Xflash (doesn't appear to be readily available on their FTP). When we gathered some information using this utility, my colleague found something very strange: root@mogile2 test]# ./xflash.dat -i get avail Initializing Interface. Expander: SAS2X36 (SAS2x36) 1) SAS2X36 (SAS2x36) (50030480:00EE917F) (0.0.0.0) 2) SAS2X36 (SAS2x36) (50030480:00E9D67F) (0.0.0.0) 3) SAS2X36 (SAS2x36) (50030480:0112D97F) (0.0.0.0) This lists the connected enclosures. You see the 3 connected (we have since added a 3rd and a 4th which is not yet showing up) with their respective SAS address / WWN (50030480:00EE917F). Now we can use this address to get information on the individual enclosures: [root@mogile2 test]# ./xflash.dat -i 5003048000EE917F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:00EE917F Enclosure Logical Id: 50030480:0000007F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 [root@mogile2 test]# ./xflash.dat -i 5003048000E9D67F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:00E9D67F Enclosure Logical Id: 50030480:0000007F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 [root@mogile2 test]# ./xflash.dat -i 500304800112D97F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:0112D97F Enclosure Logical Id: 50030480:0112D97F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 Did you catch it? The first 2 enclosures logical ID is partially masked out where the 3rd one (which has a correct unique enclosure ID) is not. We pointed this out to Supermicro and were able to confirm that this address is supposed to be set during manufacturing and there was a problem with a certain batch of these enclosures where the logical ID was not set. We believe that the RAID controller is determining the ID based on the logical ID and since our first 2 enclosures have the same logical ID, they get the same enclosure ID. We also confirmed that 0000007F is the default which comes from LSI as an ID. The next pointer that helps confirm this could be a manufacturing problem with a run of JBODs is the fact that all 6 of the enclosures that have this problem begin with 00E. I believe that between 00E8 and 00EE Supermicro forgot to program the logical IDs correctly and neglected to recall or fix the problem post production. Fortunately for us, there is a tool to manage the WWN and logical ID of the devices from Supermicro: ftp://ftp.supermicro.com/utility/ExpanderXtools_Lite/. Our next step is to schedule a shutdown of these JBODs (after data migration) and reprogram the logical ID and see if it solves the problem. Update 06/28/12 #2: I just discovered this FAQ at Supermicro while Google searching for "lsi 0000007f": http://www.supermicro.com/support/faqs/faq.cfm?faq=11805. I still don't understand why, in the last several times we contacted Supermicro, they would have never directed us to this article :\

    Read the article

  • ASP.NET Membership ChangePassword control - Need to check for previous password

    - by Steve
    Hi guys, I have a new table that hold old passwords, I need to check if there is a match. If there is a match I need the ChangePassword contol to NOT change the password. I need to tell the user that this password was used and pic a new one. I can't seem to be able to interrupt the control from changing the password. Maybe I am using the wrong event. Here is a piece of my code, or how I wish it would work. I appreciate all your help. protected void ChangePassword1_ChangedPassword(object sender, EventArgs e) { MembershipUser user = Membership.GetUser(); string usrName = ""; if (user != null) { string connStr = ConfigurationManager.ConnectionStrings["LocalSqlServer"].ConnectionString; SqlConnection mySqlConnection = new SqlConnection(connStr); SqlCommand mySqlCommand = mySqlConnection.CreateCommand(); mySqlCommand.CommandText = "Select UserName from OldPasswords where UserName = 'test'"; mySqlConnection.Open(); SqlDataReader mySqlDataReader = mySqlCommand.ExecuteReader(CommandBehavior.Default); while (mySqlDataReader.Read()) { usrName = mySqlDataReader["UserName"].ToString(); if (usrName == user.ToString()) { Label1.Text = "Match"; } else { Label1.Text = "NO Match!"; } }

    Read the article

  • How to use drag and drop within a UIScrollView

    - by user249488
    I am trying to drag and drop UIViews within a UIScrollView. I'd like the UIScrollView to scroll if I drag a UIView so that it intersects the top or bottom of the ScrollView. If it touches the top, it should scroll up. If it touches the bottom, it should scroll down. Once the UIView is moved such that it is no longer intersecting the top or bottom, the scrolling should stop. The first approach I tried was to start an NSTimer whenever I detected that the UIView intersected with the top or bottom of the scrollview. The timer would scroll the UIScrollView bit by bit until it was invalidated. This resulted in very jerky scrolling, since there is no way to predict when the timers will fire. My current approach is to simply scroll all the way to the top or bottom of the ScrollView, like this: [UIView beginAnimations:nil context:NULL]; [UIView setAnimationCurve:UIViewAnimationCurveEaseInOut]; [UIView setAnimationDuration:1.0]; [self.parentScrollview setContentOffset:newOffset animated:NO]; [UIView commitAnimations]; In order to stop scrolling, I try to determine the position of the touch in the touchesMoved: delegate, and use that to calculate the contentOffset to use for the scrollView. The problem is, when I try to get the location in the view via [[touches anyObject] locationInView:self], I get the final end location, rather than the current location. I'm guessing that's because the contentOffset on the scrollView is set immediately. Is there a way to get the actual location of a touch in a situation like this? Or any other way to set the contentOffset when I interrupt the scrolling animation?

    Read the article

  • When does a PHP <5.3.0 daemon script receive signals?

    - by MidnightLightning
    I've got a PHP script in the works that is a job worker; its main task is to check a database table for new jobs, and if there are any, to act on them. But jobs will be coming in in bursts, with long gaps in between, so I devised a sleep cycle like: while(true) { if ($jobs = get_new_jobs()) { // Act upon the jobs } else { // No new jobs now sleep(30); } } Good, but in some cases that means there might be a 30 second lag before a new job is acted upon. Since this is a daemon script, I figured I'd try the pcntl_signal hook to catch a SIGUSR1 signal to nudge the script to wake up, like: $_isAwake = true; function user_sig($signo) { global $_isAwake; daemon_log("Caught SIGUSR1"); $_isAwake = true; } pcntl_signal(SIGUSR1, 'user_sig'); while(true) { if ($jobs = get_new_jobs()) { // Act upon the jobs } else { // No new jobs now daemon_log("No new jobs, sleeping..."); $_isAwake = false; $ts = time(); while(time() < $ts+30) { sleep(1); if ($_isAwake) break; // Did a signal happen while we were sleeping? If so, stop sleeping } $_isAwake = true; } } I broke the sleep(30) up into smaller sleep bits, in case a signal doesn't interrupt a sleep() command, thinking that this would cause at most a one-second delay, but in the log file, I'm seeing that the SIGUSR1 isn't being caught until after the full 30 seconds has passed (and maybe the outer while loop resets). I found the pcntl_signal_dispatch command, but that's only for PHP 5.3 and higher. If I were using that version, I could stick a call to that command before the if ($_isAwake) call, but as it currently stands I'm on 5.2.13. On what sort of situations is the signals queue interpreted in PHP versions without the means to explicitly call the queue parsing? Could I put in some other useless command in that sleep loop that would trigger a signal queue parse within there?

    Read the article

  • Parsing some particular statements with antlr3 in C target

    - by JCD
    Hello all! I have some questions about antlr3 with tree grammar in C target. I have almost done my interpretor (functions, variables, boolean and math expressions ok) and i have kept the most difficult statements for the end (like if, switch, etc.) 1) I would like interpreting a simple loop statement: repeat: ^(REPEAT DIGIT stmt); I've seen many examples but nothing about the tree walker (only a topic here with the macros MARK() / REWIND(m) + @init / @after but not working (i've antlr errors: "unexpected node at offset 0")). How can i interpret this statement in C? 2) Same question with a simple if statement: if: ^(IF condition stmt elseifstmt* elsestmt?); The problem is to skip the statement if the condition is false and test the other elseif/else statements. 3) I have some statements which can stop the script (like "break" or "exit"). How can i interrupt the tree walker and skip the following tokens? 4) When a lexer or parser error is detected, antlr returns an error. But i would like to make my homemade error messages. How can i have the line number where parser crashed? Ask me if you want more details. Thanks you very much (and i apologize for my poor english)

    Read the article

  • Ruby on rails: Staring mongrel server

    - by spin-docta
    I know mongrel is the default server for "script/server" but when I do that command I get webrick. (I had it working before with mongrel). Now when I tell is to use mongrel ("script/server mongrel") the server fails to start up in the terminal. I get this: $ script/server mongrel ^C/Library/Ruby/Gems/1.8/gems/mongrel-1.1.5/lib/mongrel/gems.rb:11:in `require': Interrupt from /Library/Ruby/Gems/1.8/gems/mongrel-1.1.5/lib/mongrel.rb:17 from /Library/Ruby/Site/1.8/rubygems/custom_require.rb:36:in `gem_original_require' from /Library/Ruby/Site/1.8/rubygems/custom_require.rb:36:in `require' from /Library/Ruby/Gems/1.8/gems/activesupport-2.3.3/lib/active_support/dependencies.rb:156:in `require' from /Library/Ruby/Gems/1.8/gems/activesupport-2.3.3/lib/active_support/dependencies.rb:521:in `new_constants_in' from /Library/Ruby/Gems/1.8/gems/activesupport-2.3.3/lib/active_support/dependencies.rb:156:in `require' from /Library/Ruby/Gems/1.8/gems/rack-1.0.0/lib/rack/handler/mongrel.rb:1 from /Library/Ruby/Gems/1.8/gems/rack-1.0.0/lib/rack/handler.rb:17:in `const_get' from /Library/Ruby/Gems/1.8/gems/rack-1.0.0/lib/rack/handler.rb:17:in `get' from /Library/Ruby/Gems/1.8/gems/rack-1.0.0/lib/rack/handler.rb:17:in `each' from /Library/Ruby/Gems/1.8/gems/rack-1.0.0/lib/rack/handler.rb:17:in `get' from /Users/devinross14/.gem/ruby/1.8/gems/rails-2.3.3/lib/commands/server.rb:45 from /Library/Ruby/Site/1.8/rubygems/custom_require.rb:31:in `gem_original_require' from /Library/Ruby/Site/1.8/rubygems/custom_require.rb:31:in `require' from script/server:3 I just upgraded to snow leopard if that helps...

    Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >