Search Results

Search found 1170 results on 47 pages for 'jeff atwood'.

Page 18/47 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

• How do I prevent a tar pipe from causing swapping?

  - by Jeff Shattock

  I have a rather large filesystem that I need to transfer from one Linux server to another. I figured the best way to do this was via a tar/netcat pipe arrangment, something like tar c . | pv | nc blah blah blah And it works great, the network stays fairly saturated, life is good. Until the source machine starts swapping. The files are on a raid on the source system, so the read speed is much faster than the write speed on the other end. Since the dest machine hasnt picked up the data yet, the source machine needs to stick it somewhere, so into RAM it goes, until there is no more free RAM. It then starts swapping, which is horribly painful since that machine has its OS installed on a somewhat slow CF card. Both machines have 4GB of physical ram, 64 bit Ubuntu 9.04 server. GigE link between them. How do I prevent this swapping? Can I put a "speed-limit" on the tar or netcat process so that the transfer speed doesn't overwhelm the write throughput on the destination end? The man pages didn't list anything, but there might be something I'm overlooking.

  Read the article

• How do I update my servers' domain name for Reverse DNS?

  - by Jeff

  I'm updating my mail servers' rDNS and I think I have it all figured out except for one thing. When I installed my OS (Debian Etch), the installer asked me to enter the "domain name". Is the "domain name" updated by using the hostname command? If so, which config file(s) are updated when using the hostname command? If not, how do I change my servers' domain name? My current /etc/hosts: 127.0.0.1 localhost 67.228.178.164 mrspock.example-old.com mrspock My current /etc/hostname: mrspock $ hostname -f mrspock.example-old.com I need to update hostname -f to be mrspock.example-new.com.

  Read the article

• Rackspace Cloud Sites API (Not Cloud Servers)

  - by Jeff

  I'm looking for a way to pull data from my Rackspace Cloud SITES account. The data I want to pull is bandwidth, diskspace, and compute cycles (all available from control panel). I'd like to set up my own warning system, to be notified if I'm close to my limits on any given month. Does anyone know of a way/API to do this?

  Read the article

• Blocking IP address with port forwarding

  - by Jeff Storey

  I have a website setup behind a router, so the router has the external facing address and it will forward requests to the webserver inside the network. If there are X number of invalid login attempts, that IP address will be blocked from logging in. The problem is that because the site is being accessed through port forwarding, all requests show up as though they are coming from the router address, and thus the router address becomes the blocked IP. I'm not sure if this is a limitation of the router (linksys wrt160n) or if this a more general issue. Is there a way to handle this?

  Read the article

• What Device/System to use as a "router on a stick"

  - by Jeff Leyser

  I need to create several distinct VLANs, and provide a way for traffic to move between them. A "router on a stick" approach seems ideal: Internet | Router with Trunking Capability ("router on a stick") * * Trunk between router and switch * Switch with Trunking Capability | | | | | | | | | | | LAN 2 | LAN 4 | | 10.0.2.0/24 | 10.0.4.0/24 | | | | LAN 1 LAN 3 LAN 5 10.0.1.0/24 10.0.3.0/24 10.0.5.0/24 We have trunk-capable Layer-2 switches. The question is what to use as the router on a stick. My choices seem to be: 1) Use an existing Cisco 5505 ASA firewall. It appears the ASA can do the routing, but it's a 100Mbps device, and so seems sub-optimal at best 2) Buy a router. This seems overkill. 3) Buy a Layer-3 switch. Also seems overkill. 4) Use an existing Linux Box as a router 5) Use a new Linux box as a router' 6) Something I'm not thinking of I think either (4) or (5) is my best option, but I'm not sure how to choose between them. I expect the amount of traffic that has to cross the VLANs to be somewhat small, but bursty. How much load does routing add to a CentOS machine?

  Read the article

• Printer Properties not sending the correct page size to program

  - by Jeff

  We have a Zebra 2844 Label Printer with 4"x3" labels in it. When we check the page settings in Windows XP, it is set to the correct size. When we go to print out of any program, it prints 4"x11". I have checked the page settings in one of the programs that we are using and it does show correctly the 4"x3" settings but prints at the incorrect 4"x11". I have followed the steps here Paper size: Printer Properties vs Page Setup and here Is there a way to programatically set the printer properties in windows? but have not been able to glean enough information to figure it out. If anyone can help, I would appreciate it!

  Read the article

• Access Denied Error in PagesListCPVEventReceiver post SharePoint SP2 upgrade

  - by Jeff

  I am seeing the following errors from one of the SharePoint Web Front Ends after the SP2 upgrade. Has anyone else seen this error or a solution? Event Type: Error Event Source: Windows SharePoint Services 3 Event Category: General Event ID: 6875 Date: 2009-10-27 Time: 13:09:57 User: N/A Computer: XXXXXXX Description: Error loading and running event receiver Microsoft.SharePoint.Publishing.PagesListCPVEventReceiver in Microsoft.SharePoint.Publishing, Version=12.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429c. Additional information is below. : Access is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED)) For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• Managing service passwords with Puppet

  - by Jeff Ferland

  I'm setting up my Bacula configuration in Puppet. One thing I want to do is ensure that each password field is different. My current thought is to hash the hostname with a secret value that would ensure each file daemon has a unique password and that password can be written to both the director configuration and the file server. I definitely don't want to use one universal password as that would permit anybody who might compromise one machine to get access to any machine through Bacula. Is there another way to do this other than using a hash function to generate the passwords? Clarification: This is NOT about user accounts for services. This is about the authentication tokens (to use another term) in the client / server files. Example snippet: Director { # define myself Name = <%= hostname $>-dir QueryFile = "/etc/bacula/scripts/query.sql" WorkingDirectory = "/var/lib/bacula" PidDirectory = "/var/run/bacula" Maximum Concurrent Jobs = 3 Password = "<%= somePasswordFunction =>" # Console password Messages = Daemon }

  Read the article

• Best DSL hardware for ADSL Troubleshooting

  - by Jeff Sacksteder

  I have a situation where I need to make the best of a bad DSL situation. The CPE is a black box with no access to DSL diagnostics. My plan is to get some sort of DSL hardware that exposes link-layer state and gives me knobs to tweak. I'd like to be able to mitigate bufferbloat as much as I can while I'm at it. The obvious choice would seem to be a Sangoma card in a linux system. I have no way of knowing if that will do anything for me without testing it, however. I have no other access to WAN troubleshooting equipment. Are there any other options avail to me as a consumer?

  Read the article

• Cannot write to directory after taking ownership

  - by jeff charles

  I had a directory on an internal hard-drive that was created in an old Windows 7 install. After re-installing my operating system, when I try to create a new directory inside that directory, I get an Access Denied message. This isn't a protected directory, just a random directory I created at the drive root (that drive was not the C drive in either install). I tried to take ownership by opening folder properties, going to the Security tab, clicking on Advanced, going to Owner tab, clicking on Edit, selecting my user account, checking Replace owner on subcontainers and objects, and clicking Apply. There were no error messages and I closed the dialogs. I rebooted, checked the owner on that folder and a couple subfolders and it appears to be set correctly. I am still getting an Access Denied message however when trying to create a directory in it. I've also tried using attrib -R . to remove any possible readonly attribute inside the directory in an admin command prompt but am still unable to create a directory using a non-admin prompt (it does work in an admin prompt). Is there anything I can do to get write access to that folder and it's subcontents in a non-elevated context without disabling UAC?

  Read the article

• How can I find out which service is keeping Vista from restarting?

  - by Jeff

  Running Vista on my Toshiba laptop for several years now. Recently, I noticed it will not restart - I have to power cycle it. I have enabled Verbose Status messages, so I know it's stuck at "Stopping services". Is there a way to figure out which service is not stopping? I'm hoping for some kind of log like the bootlog. I've tried looking through the event viewer - no luck there.

  Read the article

• ownership of hard drive recoveery of files Windows 7

  - by Jeff

  Here is the issue. I have an old laptop that died that was running xp. I now have a win 7 laptop. I need to get the files off the old drive. Win 7 will not let me take ownership of the drive. I can runn the comand prompt in regular mode and do a dir on the drive that shows up as Q: drive in regular mode. I gives me the volume as c and the serial number. I can not take ownership in regular mode with the comand prompt or other means. Microsoft site says use safe mode with networking. So I go to safe mode the drive shows up as G: in safe mode. I use the comand prompt Takeown /f G: and get the device is not ready error. I am at a loss. All I want is to retrieve my files from this drive. Any ideas or sugestions. I don't see how you can dir and get some info in one mode and not acces it in another. I have to get ownership and permissions fixed to get in the drive to get my files. Thanks in advance. I might add that I am using a usb3.0 to ide/sata cable adapter. Software came with the device but I can't make heads or tails out of the manual to know if any of the software can help me. The soft ware is PCClone Ex lite, and Clone Drive Soft ware

  Read the article

• Upgrade CentOS 5.2 to 5.3 -- but not 5.4

  - by Jeff Leyser

  Server currently running CentOS 5.2. Developers tell me they'd like the machine upgrade to CentOS 5.3 -- but not all the way to CentOS 5.4, as they haven't tested with 5.4 yet. I'm pretty sure a yum upgrade will put me at 5.4, as a yum check-update shows all sorts of 5.4 packages. So how do I move up to 5.3?

  Read the article

• Will the Core i3 stock cooler fit in a 2U case?

  - by Jeff Shattock

  I can not find the dimensions of the Core i3 stock cooler anywhere. Will a Core i3 stock cooler fit in a 2U rackmount case?

  Read the article

• Can I use any USB hub with an XBOX360 and Rockband controllers? [closed]

  - by Jeff Yates

  I've seen USB hubs specifically created for RockBand. Are they required or is this just marketing? Will any old USB hub work? My gut says yes, but my wallet says ask someone else.

  Read the article

• In Outlook 2010, can you add "Categories" to the "New Email" Ribbon?

  - by Jeff

  I couldn't figure out how to do this in Outlook 2007, and I was hoping I could do it in Outlook 2010... I want the ability to quickly apply a category when composing a new email (typically a "Waiting For..." category) for things that need a response. It is possible to apply a category by clicking the "Options" ribbon, then the little arrow under the More Options section - but why can't I get the nice big "Categories" drop-down that's available in the "Tags" section of the main Outlook window. There are about a kabillion commands in the "Customize Ribbon" dialog box for the New Mail window, but I couldn't find anything about Categories. Should I just give up?

  Read the article

• Server 2008 email on Event variables

  - by Jeff Miles

  One of the new features of Server 2008 is the ability to attach a task to a specific event in the event logs. One of the actions available is to send an email through a SMTP server. This is working great, however it would be ideal if in the message body, the Event contents could be placed. I have tried using $eventdescription and %eventdescription%, but those are just shots in the dark. Any amount of googling produces no results. Does anyone know if this is possible? Update: Sparks' suggestion below is a step in the right direction I believe, however that method doesn't seem to work for all values. For example, I can pull the RecordID, Severity and Channel as shown, but I can't use the same method to retreive the EventID, or most importantly the description. Here's the raw XML from one event: [Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"] [System] [Provider Name="DFSR" /] [EventID Qualifiers="16384"]4412[/EventID] [Level]4[/Level] [Task]0[/Task] [Keywords]0x80000000000000[/Keywords] [TimeCreated SystemTime="2009-05-14T18:18:09.000Z" /] [EventRecordID]45692[/EventRecordID] [Channel]DFS Replication[/Channel] [Computer]servername.domain.com[/Computer] [Security /] [/System] [EventData] [Data]9046C3F4-843E-4A53-B941-4B20764072E5[/Data] [Data]D:\departments\Geomatics\Plan Quality\Data Processing\CG3533017 2009-05-13 KT FIXED[/Data] [Data]D:\departments[/Data] [Data]{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [Data]Departments[/Data] [Data]domain.ca\files\departments[/Data] [Data]B8242CE2-F5EB-47DA-BA5B-1DD2F7EE3AB9[/Data] [Data]DFAA7A54-66CB-4C31-81A0-0F861382C32C[/Data] [Data]CG3533017 2009-05-13-{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [/EventData] [/Event] I have tried using a ValueQuery for EventData, but it returns no data.

  Read the article

• SQL Server Logs: missing date ranges

  - by Jeff

  I need to be able to export SQL Server logs into CSV files, which I can easily do with the export function. However in doing so I've noticed there's a range of dates missing from the SQL Server logs in Management Studio, two months actually. I'm wondering where these logs might be found, and if it's possible to reload them so I can view and then export them. They're strictly for informational purposes, but I do need them. Thanks in advance!

  Read the article

• Cannot access shares via \\servername but \\ip works

  - by Jeff

  To set up the scenario: One of our techs set one of the domain controllers to use Microsoft time. The time IS correct (including Time Zone) and DOES match the other domain controller's time; it was previously incorrect, however. Since the change, no users can connect via \\servername\share or \\servername.domainname.com but \\ip\share works fine. I cannot even access it from the other domain controller with which I know both have the same time. The servername DOES resolve to the correct IP address. Also, strangely enough, \\domainname.com works as well which resolves to the same server. Finally Everything that I have tried does resolve to the same, correct IP address. The error is: login failure: The target account name is incorrect. I believe it is time related but since the times are correct and match I'm not sure. Anyone know what might cause this?

  Read the article

• Windows 7 laptop with two active network connections will not perform DNS AAAA lookup under certain conditions

  - by Jeff Loughridge

  My laptop has two network interfaces. The Ethernet interface connects directly to my provider's edge router. It obtains an IPv6 address via SLAAC. I manually set an IPv6 DNS server. The wireless interface connects to a CPE router that doesn't understand IPv6. If the wireless interface is disabled, I can reach the IPv6 Internet with no problems using the Ethernet interface. I run into problems when both interfaces are enabled and the wireless interface get its IPv4 DNS server via DHCP. Let's look at two scenarios. Wireless interface obtains IPv4 DNS server via DHCP - The CPE router (192.168.0.1) sends its address as the DNS server. In this scenario, Windows 7 will not perform AAAA lookups. The browser uses IPv4 transit to reach dual stack web sites. I can't reach IPv6-only web sites using domain names. I can reach IPv6-enabled web sites using IPv6 literals instead of the domain name. Wireless interface is manually configured with OpenDNS DNS server - Windows 7 performs AAAA lookups using IPv6 transit (via the Ethernet). Everything works fine. My dual homed set-up is definitely not standard. Still, the behavior is very strange to me. A valid IPv6 interface exists in my Ethernet interface. Why won't Windows attempt AAAA lookups in scenario #1? I've included the output of ipconfig /all and netstat -rn. C:\Program Files\Console>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : jake Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : res.openband.net Wireless LAN adapter Wireless Network Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter Physical Address. . . . . . . . . : C0-CB-38-06-54-F9 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : res.openband.net Description . . . . . . . . . . . : DW1520 Wireless-N WLAN Half-Mini Card Physical Address. . . . . . . . . : C0-CB-38-06-54-F9 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::fc39:9293:7d01:4a75%13(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.105(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Wednesday, July 11, 2012 7:35:21 AM Lease Expires . . . . . . . . . . : Thursday, July 12, 2012 9:49:46 AM Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DHCPv6 IAID . . . . . . . . . . . : 364956472 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-80-F8-14-5C-26-0A-03-23-5C DNS Servers . . . . . . . . . . . : 208.67.222.222 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : res.openband.net Description . . . . . . . . . . . : Intel(R) 82577LM Gigabit Network Connection Physical Address. . . . . . . . . : 5C-26-0A-03-23-5C DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2607:2600:1:850:c0e9:211a:fd05:4e0b(Preferred) Temporary IPv6 Address. . . . . . : 2607:2600:1:850:3d29:1839:62db:c4c1(Preferred) Link-local IPv6 Address . . . . . : fe80::c0e9:211a:fd05:4e0b%12(Preferred) IPv4 Address. . . . . . . . . . . : 10.52.2.51(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.254.0 Lease Obtained. . . . . . . . . . : Monday, July 09, 2012 8:55:07 AM Lease Expires . . . . . . . . . . : Thursday, July 12, 2012 7:30:05 AM Default Gateway . . . . . . . . . : fe80::214:6aff:fe51:7f3f%12 10.52.2.1 DHCP Server . . . . . . . . . . . : 216.40.77.244 DNS Servers . . . . . . . . . . . : 2620:0:ccc::2 2620:0:ccd::2 216.40.77.126 216.40.77.244 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::4c61:495b:229e:281e%14(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.40.1(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 469782614 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-80-F8-14-5C-26-0A-03-23-5C DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::f996:61eb:8c00:45e6%15(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.17.1(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 486559830 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-80-F8-14-5C-26-0A-03-23-5C DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled C:\Program Files\Console>netstat -rn =========================================================================== Interface List 17...c0 cb 38 06 54 f9 ......Microsoft Virtual WiFi Miniport Adapter 13...c0 cb 38 06 54 f9 ......DW1520 Wireless-N WLAN Half-Mini Card 12...5c 26 0a 03 23 5c ......Intel(R) 82577LM Gigabit Network Connection 11...5c ac 4c f8 b8 55 ......Bluetooth Device (Personal Area Network) 14...00 50 56 c0 00 01 ......VMware Virtual Ethernet Adapter for VMnet1 15...00 50 56 c0 00 08 ......VMware Virtual Ethernet Adapter for VMnet8 1...........................Software Loopback Interface 1 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.52.2.1 10.52.2.51 10 0.0.0.0 0.0.0.0 192.168.0.1 192.168.0.105 100 10.52.2.0 255.255.254.0 On-link 10.52.2.51 261 10.52.2.51 255.255.255.255 On-link 10.52.2.51 261 10.52.3.255 255.255.255.255 On-link 10.52.2.51 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 On-link 192.168.0.105 306 192.168.0.105 255.255.255.255 On-link 192.168.0.105 306 192.168.0.255 255.255.255.255 On-link 192.168.0.105 306 192.168.17.0 255.255.255.0 On-link 192.168.17.1 276 192.168.17.1 255.255.255.255 On-link 192.168.17.1 276 192.168.17.255 255.255.255.255 On-link 192.168.17.1 276 192.168.40.0 255.255.255.0 On-link 192.168.40.1 276 192.168.40.1 255.255.255.255 On-link 192.168.40.1 276 192.168.40.255 255.255.255.255 On-link 192.168.40.1 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.52.2.51 261 224.0.0.0 240.0.0.0 On-link 192.168.0.105 306 224.0.0.0 240.0.0.0 On-link 192.168.40.1 276 224.0.0.0 240.0.0.0 On-link 192.168.17.1 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.52.2.51 261 255.255.255.255 255.255.255.255 On-link 192.168.0.105 306 255.255.255.255 255.255.255.255 On-link 192.168.40.1 276 255.255.255.255 255.255.255.255 On-link 192.168.17.1 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 12 261 ::/0 fe80::214:6aff:fe51:7f3f 1 306 ::1/128 On-link 12 13 2607:2600:1:850::/64 On-link 12 261 2607:2600:1:850:3d29:1839:62db:c4c1/128 On-link 12 261 2607:2600:1:850:c0e9:211a:fd05:4e0b/128 On-link 12 261 fe80::/64 On-link 13 281 fe80::/64 On-link 14 276 fe80::/64 On-link 15 276 fe80::/64 On-link 14 276 fe80::4c61:495b:229e:281e/128 On-link 12 261 fe80::c0e9:211a:fd05:4e0b/128 On-link 15 276 fe80::f996:61eb:8c00:45e6/128 On-link 13 281 fe80::fc39:9293:7d01:4a75/128 On-link 1 306 ff00::/8 On-link 12 261 ff00::/8 On-link 13 281 ff00::/8 On-link 14 276 ff00::/8 On-link 15 276 ff00::/8 On-link =========================================================================== Persistent Routes: None

  Read the article

• pam_tty_audit and non privileged users

  - by Jeff

  I'm working on a cents 6.3 box and am trying to log all commands executed from a bash shell and came across pam_tty_audit. I've added the appropriate line to my /etc/pam.d/system-auth file: "session required pam_tty_audit.so enable=*" The problem is that it does not appear to capture commands unless a user is root. For example, if i ssh in as root it logs everything to the audit log, but if I ssh as a regular user it does not start logging anything until after I have su to root. Any ideas?

  Read the article

• Sharepoint 2010 reacts very badly to having it's IP address changed. How do I fix it?

  - by Jeff Sacksteder

  I have Sharepoint 2010 set up on a virtual host for prototyping various projects. If I restart the host, the IP changes. Afterwards, SP complains that it can't find it's configuration database. I can't find where it might be storing an IP. To clarify, the URL remains the same - I have a dynamic dns solution in place to handle that. I can't see anything in the web.config files or the database connection strings that would indicate a hardcoded IP. How can I fix this up in less time than re-installing every time I need to do a project?

  Read the article

• Server 2008 email on Event variables

  - by Jeff Miles

  One of the new features of Server 2008 is the ability to attach a task to a specific event in the event logs. One of the actions available is to send an email through a SMTP server. This is working great, however it would be ideal if in the message body, the Event contents could be placed. I have tried using $eventdescription and %eventdescription%, but those are just shots in the dark. Any amount of googling produces no results. Does anyone know if this is possible? Update: Sparks' suggestion below is a step in the right direction I believe, however that method doesn't seem to work for all values. For example, I can pull the RecordID, Severity and Channel as shown, but I can't use the same method to retreive the EventID, or most importantly the description. Here's the raw XML from one event: [Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"] [System] [Provider Name="DFSR" /] [EventID Qualifiers="16384"]4412[/EventID] [Level]4[/Level] [Task]0[/Task] [Keywords]0x80000000000000[/Keywords] [TimeCreated SystemTime="2009-05-14T18:18:09.000Z" /] [EventRecordID]45692[/EventRecordID] [Channel]DFS Replication[/Channel] [Computer]servername.domain.com[/Computer] [Security /] [/System] [EventData] [Data]9046C3F4-843E-4A53-B941-4B20764072E5[/Data] [Data]D:\departments\Geomatics\Plan Quality\Data Processing\CG3533017 2009-05-13 KT FIXED[/Data] [Data]D:\departments[/Data] [Data]{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [Data]Departments[/Data] [Data]swg.ca\files\departments[/Data] [Data]B8242CE2-F5EB-47DA-BA5B-1DD2F7EE3AB9[/Data] [Data]DFAA7A54-66CB-4C31-81A0-0F861382C32C[/Data] [Data]CG3533017 2009-05-13-{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [/EventData] [/Event] I have tried using a ValueQuery for EventData, but it returns no data.

  Read the article

• Deleting file in Samba doesn't delete file?

  - by Jeff Welling

  Why, when I delete some files in Samba, does it not delete them but instead merely change their filename from filename.txt to ._filename.txt? This is not the behaviour one would expect when "deleting" a file, so I'm wondering if there's an option I forgot to set somewhere in the samba config. It does this to some files but not to others, I have not yet spotted a pattern to its choosiness. There is a Ubuntu 12.04 machine and a Mac OS X machine which have write (and thus delete) capability, no Windows machines have write permission.

  Read the article

• Stop Windows 7 from accessing or writing to hard drive unless "told" to by me? (More info inside...)

  - by Jeff

  A confusing question, perhaps, but bear with me. I have two internal HDDs set up in a RAID0 array which I use as mass storage. I access the drive very infrequently (once a day at most) and so I have set up Windows 7's power options to turn off idle disks after only 1 minute. This is fine, and the disks are turned off most of the time. However, I notice that Windows sometimes spins up the drives when I really, really don't want or need it to. This causes a 30 second delay as both drives spin up and lock up my system. Some examples of when this happens: 1) When I'm installing something using Windows Installer or Installshield; it seems to me as if they're using the drive with most available free space as the installer cache location... so my big RAID drive has to spin up! Most annoying. 2) Apparently, when I open a Java-based program which resides on my system drive and has nothing to do with my RAID drive! 3) At boot-up and shut-down time. At shutdown the drive spin up only for the computer to immediately shut down! Incredibly frustrating! I've already tried changing the letter of the drive, and at some points have removed the drive letter entirely, which solves the first two issues above. So my question (FINALLY!) is this: is there any way I can mark this drive as being for "storage only", so Windows basically does not see it at all until I actually invoke it somehow? Or is there any way I could set it up so that only specific programs have write access to it? For example, download managers, TeraCopy, etc. etc.? Basically I want it to be a "ghost drive" until I'm ready to use it and to stop Windows from spinning it up all the damn time! Thank you. :)

  Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >