Search Results

Search found 5373 results on 215 pages for 'wireless bridge'.

Page 18/215 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

  • Wireless does not work 12.10

    - by superkoop
    My primary issue is that my wireless does not work after I installed 12.10. The output to rfkill list all: 5: hci0: Bluetooth Soft blocked: no Hard blocked: no The output to lshw -class network is: *-network description: Ethernet interface product: 88E8040 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 12 serial: 00:21:9b:d6:46:51 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full ip=192.168.1.102 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:44 memory:fe8fc000-fe8fffff ioport:de00(size=256) *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0b:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:17 memory:fe7fc000-fe7fffff The output to lspci -nn for the pertinent information is: 0b:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01) Thus, it seems the solution would be to run: sudo apt-get install linux-headers-generic sudo apt-get install --reinstall bcmwl-kernel-source sudo modprobe wl However, I do not currently have access to an ethernet connection, as I am currently only able to use verizon wireless 3g internet. Thus, is there a way to set up ICS with a Vista machine so that I can access the internet by using the Vista machine as the host? Or, is it possible to fix this by downloading the important packages in vista and moving them to ubuntu via USB drive?

    Read the article

  • Can't connect to Wireless

    - by SimplyRed37
    Good day all! I hope you are doing good. I have performed a WUBI installation of 12.04 on my HP G62 laptop, which has an Atheros AR9285 wireless chipset. Everything works fine with my wired network connection. However, wireless is unable to connect to my wifi network. I enter the WPA2 key and then it attemps to connect, but eventually comes back, asking for the WPA2 key again, as if it was not good. All of the other laptops in the household are able to connect, using the same key (I configured them all, so I am 500% sure of the WPA2 key). Any idea as to what could be causing this? I can definitely post the output of CLI commands like "rfkill list" or "sudo lshw -class network", or "ifconfig". I have installed Ubuntu a few time but I am definitely still a newbie, but I am definitely computer savyy. Looking forward to suggestions . Thanks in advance !!! Dan...

    Read the article

  • How to set up wireless access on a Cisco router

    - by Carlos
    Hi, I've set up my 877W according to the configuration listed in this forum post: IPTV over Cisco 877 (It's the working configuration at the bottom of the post) Note that I have an 877W, so it also has a wireless radio. Now, I've gotten the whole setup to work, so IPTV is working, and I can access the internet via the ethernet ports. Now I'm trying to figure out how to allow access via the dot11radio interface. I've gathered that I basically need to create a bridge group, and bridge the radio to the internet VLAN. However, when I add a bridge-group 2 command to VLAN1, it seems to take down the whole internet VLAN. (The IPTV continues to work.) This makes the router itself inaccessible (I've got a laptop, so no serial) and I end up having to reboot the router. Can anyone tell me how to a) Allow wireless access to the internet (preferably with WEP, to match my old router) b) Determine what makes the router inaccessible when I add the new bridge group c) Forward the IPTV traffic onto a machine on my internet VLAN

    Read the article

  • WiFi can't reconnect after suspend/hibernate on Ubuntu 12.04.1

    - by CyberOPS
    I've had this problem since Ubuntu 11.10 (my first install) but I was able to get around this issue with this answer. When I updated to Ubuntu 12.04 I encrypted the home folder, so I wasn't able to suspend or hibernate anymore (disappointing :l). Because of this and another issue I had1, I chose to reinstall. Sometime after I reinstalled, I was reminded about reconnection issue because it wasn't working after I suspended. I tried to use the same fix as before but I couldn't get it to work. I've also tried a couple other different fixes I found around the web but they didn't work. Since I'm new to linux, I'm gonna have a tough time figuring this out by myself. So does anyone know how, or what I need to figure out how, to fix this? Info: Computer: HP Pavilion dv6t-6b00 CTO Quad Edition Entertainment Notebook PC Network Card: Intel® Centrino® Wireless-N 1000 OS: Ubuntu 12.04.1 (x64) dual booting with Windows 7 (x64) (Not using Wubi) Wireless Card Driver: Intel Wireless WiFi Link drivers for Linux (iwlwifi) 1 - ntfs-config caused colord to crash on startup, even after NTFS-Config was removed.

    Read the article

  • 12.04 WiFi issue on a particular access point

    - by user71706
    I have a WiFi access point that I connect to a PC to share its Internet connection with multiple machines, in a training environment. All the machines with 11.04 connect to this access point with no problem, and can access any server on the Internet. These machines have an Intel Wireless -N 1030 BGN chipset (as reported by lspci). Now, my problem is that I don't manage to connect 12.04 machines to this wireless network. The systems I tried do manage to connect (confirmed by Network Manager), but when I try to access a website like http://kernel.org, the browser shows "Connecting to kernel.org...", but displays a "The connection has timed out" error page. Other symptoms: Name resolution works (for example 'nslookup kernel.org') finds kernel.org's IP address 'ping kernel.org' doesn't work The same 12.04 machines have no problem at all with other wireless networks. So there is probably something weird in my access point (though the 11.04 machines are not impacted). Would you have any suggestions for investigating this issue? Thanks, Michael.

    Read the article

  • Slow wifi on Ubuntu 12.04 wifi driver ath9k

    - by lunar
    For the last couple of days my wifi connection is extremely slow. I am pretty sure that it is caused by the driver. Can this be improved? lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"MyWiFi" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:68:FE:7B:C7 Bit Rate=58.5 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:6960 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: 74:f0:6d:34:c2:4e width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d7400000-d740ffff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:4b:38:78:f6:ae capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128) lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 04f2:b1bb Chicony Electronics Co., Ltd Bus 001 Device 004: ID 0b05:1788 ASUSTek Computer, Inc. lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 06) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [GeForce GT 425M] (rev a1) 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 04:00.0 USB controller: Fresco Logic Device 1400 (rev 01) 06:00.0 Ethernet controller: Atheros Communications Inc. AR8131 Gigabit Ethernet (rev c0) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) rfkill list all 0: hci0: Bluetooth Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no

    Read the article

  • Macbook Pro Wireless Reconnecting

    - by A Student at a University
    I'm using a WPA2 EAP network. I'm sitting next to the access point. The connection keeps dropping and taking ~10 seconds to reconnect. My other devices are staying online. What's causing it? syslog: 01:21:10 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:21:10 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX 01:21:10 NetworkManager[XX40]: <info> (eth1): DHCPv4 state changed reboot -> renew 01:21:10 NetworkManager[XX40]: <info> address XXX.XXX.XXX.XXX 01:21:10 NetworkManager[XX40]: <info> prefix 20 (XXX.XXX.XXX.XXX) 01:21:10 NetworkManager[XX40]: <info> gateway XXX.XXX.XXX.XXX 01:21:10 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:21:10 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:21:10 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:21:10 NetworkManager[XX40]: <info> domain name 'server.domain.tld' 01:21:10 dhclient: bound to XXX.XXX.XXX.XXX -- renewal in XXX seconds. 01:33:30 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:33:30 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX 01:33:30 dhclient: bound to XXX.XXX.XXX.XXX -- renewal in XXX seconds. 01:35:13 wpa_supplicant[XX60]: CTRL-EVENT-EAP-STARTED EAP authentication started 01:35:13 wpa_supplicant[XX60]: CTRL-EVENT-EAP-METHOD EAP vendor 0 method 25 (PEAP) selected 01:35:14 wpa_supplicant[XX60]: EAP-MSCHAPV2: Authentication succeeded 01:35:14 wpa_supplicant[XX60]: EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed 01:35:14 wpa_supplicant[XX60]: CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully 01:35:14 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> 4-way handshake 01:35:14 wpa_supplicant[XX60]: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP] 01:35:14 NetworkManager[XX40]: <info> (eth1): supplicant connection state: 4-way handshake -> group handshake 01:35:14 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:35:17 wpa_supplicant[XX60]: CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys 01:35:17 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> disconnected 01:35:17 NetworkManager[XX40]: <info> (eth1): supplicant connection state: disconnected -> scanning 01:35:26 wpa_supplicant[XX60]: CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys 01:35:26 NetworkManager[XX40]: <info> (eth1): supplicant connection state: scanning -> disconnected 01:35:29 NetworkManager[XX40]: <info> (eth1): supplicant connection state: disconnected -> scanning 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 8 -> 3 (reason 11) 01:35:32 NetworkManager[XX40]: <info> (eth1): deactivating device (reason: 11). 01:35:32 NetworkManager[XX40]: <info> (eth1): canceled DHCP transaction, DHCP client pid XX27 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) starting connection 'Auto XXXXXXXXXX' 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 3 -> 4 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled... 01:35:32 NetworkManager[XX40]: <info> (eth1): supplicant connection state: scanning -> disconnected 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) started... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) scheduled... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) complete. 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) starting... 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 4 -> 5 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1/wireless): access point 'Auto XXXXXXXXXX' has security, but secrets are required. 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 5 -> 6 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) complete. 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) started... 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 6 -> 4 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) scheduled... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) complete. 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) starting... 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 4 -> 5 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1/wireless): connection 'Auto XXXXXXXXXX' has security, and secrets exist. No new secrets needed. 01:35:32 NetworkManager[XX40]: <info> Config: added 'ssid' value 'XXXXXXXXXX' 01:35:32 NetworkManager[XX40]: <info> Config: added 'scan_ssid' value '1' 01:35:32 NetworkManager[XX40]: <info> Config: added 'key_mgmt' value 'WPA-EAP' 01:35:32 NetworkManager[XX40]: <info> Config: added 'password' value '<omitted>' 01:35:32 NetworkManager[XX40]: <info> Config: added 'eap' value 'PEAP' 01:35:32 NetworkManager[XX40]: <info> Config: added 'fragment_size' value 'XXX0' 01:35:32 NetworkManager[XX40]: <info> Config: added 'phase2' value 'auth=MSCHAPV2' 01:35:32 NetworkManager[XX40]: <info> Config: added 'ca_cert' value '/etc/ssl/certs/Equifax_Secure_CA.pem' 01:35:32 NetworkManager[XX40]: <info> Config: added 'identity' value 'XXXXXXX' 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) complete. 01:35:32 NetworkManager[XX40]: <info> Config: set interface ap_scan to 1 01:35:32 NetworkManager[XX40]: <info> (eth1): supplicant connection state: disconnected -> scanning 01:35:36 wpa_supplicant[XX60]: Associated with XX:XX:XX:XX:XX:XX 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: scanning -> associated 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-EAP-STARTED EAP authentication started 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-EAP-METHOD EAP vendor 0 method 25 (PEAP) selected 01:35:36 wpa_supplicant[XX60]: EAP-MSCHAPV2: Authentication succeeded 01:35:36 wpa_supplicant[XX60]: EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: associated -> 4-way handshake 01:35:36 wpa_supplicant[XX60]: WPA: Could not find AP from the scan results 01:35:36 wpa_supplicant[XX60]: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP] 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX:XX completed (reauth) [id=0 id_str=] 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: 4-way handshake -> group handshake 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:35:36 NetworkManager[XX40]: <info> Activation (eth1/wireless) Stage 2 of 5 (Device Configure) successful. Connected to wireless network 'XXXXXXXXXX'. 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) scheduled. 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) started... 01:35:36 NetworkManager[XX40]: <info> (eth1): device state change: 5 -> 7 (reason 0) 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Beginning DHCPv4 transaction (timeout in 45 seconds) 01:35:36 NetworkManager[XX40]: <info> dhclient started with pid XX87 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) complete. 01:35:36 dhclient: Internet Systems Consortium DHCP Client VXXX.XXX.XXX 01:35:36 dhclient: Copyright 2004-2009 Internet Systems Consortium. 01:35:36 dhclient: All rights reserved. 01:35:36 dhclient: For info, please visit https://www.isc.org/software/dhcp/ 01:35:36 dhclient: 01:35:36 NetworkManager[XX40]: <info> (eth1): DHCPv4 state changed nbi -> preinit 01:35:36 dhclient: Listening on LPF/eth1/XX:XX:XX:XX:XX:XX 01:35:36 dhclient: Sending on LPF/eth1/XX:XX:XX:XX:XX:XX 01:35:36 dhclient: Sending on Socket/fallback 01:35:36 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:35:36 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX 01:35:36 dhclient: bound to XXX.XXX.XXX.XXX -- renewal in XXX seconds. 01:35:36 NetworkManager[XX40]: <info> (eth1): DHCPv4 state changed preinit -> reboot 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 4 of 5 (IP4 Configure Get) scheduled... 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 4 of 5 (IP4 Configure Get) started... 01:35:36 NetworkManager[XX40]: <info> address XXX.XXX.XXX.XXX 01:35:36 NetworkManager[XX40]: <info> prefix 20 (XXX.XXX.XXX.XXX) 01:35:36 NetworkManager[XX40]: <info> gateway XXX.XXX.XXX.XXX 01:35:36 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:35:36 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:35:36 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:35:36 NetworkManager[XX40]: <info> domain name 'server.domain.tld' 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 5 of 5 (IP Configure Commit) scheduled... 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 4 of 5 (IP4 Configure Get) complete. 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 5 of 5 (IP Configure Commit) started... 01:35:37 NetworkManager[XX40]: <info> (eth1): device state change: 7 -> 8 (reason 0) 01:35:37 NetworkManager[XX40]: <info> (eth1): roamed from BSSID XX:XX:XX:XX:XX:XX (XXXXXXXXXX) to XX:XX:XX:XX:XX:XX (XXXXXXXXX) 01:35:37 NetworkManager[XX40]: <info> Policy set 'Auto XXXXXXXXXX' (eth1) as default for IPv4 routing and DNS. 01:35:37 NetworkManager[XX40]: <info> Activation (eth1) successful, device activated. 01:35:37 NetworkManager[XX40]: <info> Activation (eth1) Stage 5 of 5 (IP Configure Commit) complete. 01:35:43 wpa_supplicant[XX60]: Trying to associate with XX:XX:XX:XX:XX:XX (SSID='XXXXXXXXXX' freq=2412 MHz) 01:35:43 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> associating 01:35:43 wpa_supplicant[XX60]: Association request to the driver failed 01:35:46 wpa_supplicant[XX60]: Associated with XX:XX:XX:XX:XX:XX 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: associating -> associated 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: associated -> 4-way handshake 01:35:46 wpa_supplicant[XX60]: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP] 01:35:46 wpa_supplicant[XX60]: CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX:XX completed (reauth) [id=0 id_str=] 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: 4-way handshake -> group handshake 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:40:47 wpa_supplicant[XX60]: WPA: Group rekeying completed with XX:XX:XX:XX:XX:XX [GTK=TKIP] 01:40:47 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> group handshake 01:40:47 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:50:19 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:50:19 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX

    Read the article

  • Ivy bridge i3 recognized as Xeon e3-1200

    - by user287072
    The situation: I've got a Ivy bridge i3 3225 which is being recognized as a Xeon e3-1200 series cpu by Ubuntu 14.04 64bit. The problem: cpu fan makes more noise than necessary (under dual-boot Win8 the fans are off), cannot install the intel graphics drivers from 01.org. Goals: - find a fix for the load fans could be they are not CPU related, I've tried some fan controller packages, but they made no difference. - get the intel graphics to install (this now fails as xeon cpu's are not supported, I got the package working on a i5 laptop) - get to know some more about how hardware recognition works Tried so far: - a reinstall of Ubuntu, but it was recognized again as a Xeon cpu. - different fan control packages, but they either do not recognized the fans, or just keep fan speed to high. Any pointers as how to get Ubuntu recognized it are more than welcome. lspci -nnQ 00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor DRAM Controller [8086:0150] (rev 09) 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port [8086:0151] (rev 09) 00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) 00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) 00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) 00:1c.5 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 6 [8086:1e1a] (rev c4) 00:1c.6 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev c4) 00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) 00:1f.0 ISA bridge [0601]: Intel Corporation Z77 Express Chipset LPC Controller [8086:1e44] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation 7 Series/C210 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e02] (rev 04) 00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04) 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GK106 [GeForce GTX 660] [10de:11c0] (rev a1) 01:00.1 Audio device [0403]: NVIDIA Corporation GK106 HDMI Audio Controller [10de:0e0b] (rev a1) 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 09) 04:00.0 PCI bridge [0604]: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge [1b21:1080] (rev 03)

    Read the article

  • Ubuntu hardware wireless switch has no effect after suspend and 13.10 upgrade

    - by blaineh
    I'm posting this on SU after it stalled on askubuntu. I hope someone here can help! If you'd prefer to answer on AU itself, here's the link: http://askubuntu.com/questions/365177/hardware-wireless-switch-has-no-effect-after-suspend-and-13-10-upgrade Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Edit. This morning, I had had the laptop suspended all night, and then when I tried to awake it, it simply wouldn't. It would try, and then it would sleep again (I guess it felt a little bit like me! </badjoke>). Is it possible these problems are related? Edit. I don't have enough reputation on SU proper to post links to pastebins and other questions I've tried, so I'm putting them in comments, and of course they're available in the original question.

    Read the article

  • How do I turn on wireless adapter on HP Envy dv6 7200 under Ubuntu (any version)?

    - by Dave B.
    I have a new HP Envy dv6 7200 with dual boot Windows 8 / Ubuntu 12.04. In windows, the F12 key in Windows activates the "airplane mode" switch which enables/disables both on-board (mini PCIe) and USB wireless adapters. In Ubuntu, however, the wireless adapter is turned off by default and cannot be turned back on via the F12 key (or any other combination of F12 and Ctrl, Fn, Shift, etc.). Let me explain the "fixes" I've seen in various forums and explain what did or did not happen. These are listed in no particular order. (Spoiler alert: wireless is still broke). Solution 1? Use HP's "Wireless Assistant" utility to permanently activate the wireless card in Windows, then boot into Ubuntu to happily find it working. Unfortunately, this utility works in Windows 7 but not Windows 8. On the other hand, hardware drivers from HP are only available for Windows 8 for this model. Catch 22 (I could not find a comparable utility for Windows 8). Solution 2? Use a USB wireless adapter to sidestep the on-board device. I purchased such a device from thinkpenguin.com to be sure that it would be Linux-friendly. However, the wireless switch enables / disables all wireless devices including USB. So, there's my $50 donation to the nice folks at thinkpenguin.com, but still no solution. Solution 3? Following the Think Penguin folk's suggestion, modify the mini PCI express adapter following instructions here: http://www.notebookforums.com/t/225429/broken-wireless-hardware-switch-fix Tempting, but I then violate the terms of my warranty mere days after opening the box. This might be a good solution for an older machine that you want to get your geek on with, but not for a new box. Solution 4? rfkill unblock all No effect whatsoever. ubuntu@ubuntu-hp-evny:~$ rfkill unblock all ubuntu@ubuntu-hp-evny:~$ rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Solution 5? Re-install drivers. Done and done. Ubuntu recognizes the device - perhaps even without re-installing the drivers? - but cannot turn it on. How do I know this? In the Network Manager drop-down menu, the wireless option is blacked out and a message reads something like: "wireless network is disabled by a hardware switch". Solution 6? Identify a physical switch on the laptop and flip it. There is no such switch on this machine. In fact, walking through Best Buy yesterday, I checked and not a single new laptop PC had a physical switch on it. All of the wireless switches are either the F2 or F12 key ... I wonder if askubuntu will not be plagued by this exact issue in the near future? Additional info - lspci ubuntu@ubuntu-hp-evny:~$ lspci 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.2 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 3 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 08:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5229 (rev 01) 0a:00.0 Network controller: Ralink corp. Device 539b 0b:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) Any suggestions would be much appreciated!

    Read the article

  • Is Wireless LTSP possible?

    - by DaimyoKirby
    Background: I've been doing research into LTSP, to see if it would be a viable option for my school. However, (almost) everything I've found say that wireless LTSP isn't possible. This is a problem since my school almost exclusively uses Apple laptops. Question: Having every classroom wire its laptops into the network is unrealistic, so is there a way to have clients wirelessly boot into the LTSP server?

    Read the article

  • Share wireless Internet connection between Ubuntu 10.04 to Windows Vista through ethernet

    - by Artyom2033
    I am connected to the internet using a wireless connection on my laptop running ubuntu 10.04 and I want to share it to a desktop running windows Vista trough a Ethernet cable. How do I do that? I've try the "GUI Method via Network Manager (Ubuntu 9.10 and up)" on this page : https://help.ubuntu.com/community/Internet/ConnectionSharing but how to I access to it from Windows Vista? I didn't even know if it is shared. Thanks for the help

    Read the article

  • Support TrendNet TEW-643PI Wireless N network card

    - by Matthew Rigdon
    Hello, Has anyone been able to get a TrendNet TEW-643PI Wireless N card working under UBUNTU, if so what drivers did you use and where did you find them. I have this card and would really like to be able to use it in my computer. I found drivers that may work but dont know how to get ubuntu to pick up the drivers. I have tried the Additional Drivers option but cannot seem to get ubuntu to pick up the drivers. Thanks.

    Read the article

  • Alfa AWUS036H USB wireless adapter not recognized

    - by GFiasco
    The Alfa AWUS036H USB wireless adapter will not be recognized by my netbook (Ubuntu 14.04, Asus X201E). As I understand it, the drivers should already be built in to this version of Linux, but I tried a make/make install of the latest Realtek drivers (as mentioned on How do I install drivers for the Alfa AWUS036H USB wireless adapter?) and it didn't work. I then followed the advice of this thread (ALFA AWUS036NH driver) and did a make/make install of the most up-to-date backport of the drivers, but that didn't work. At this point I tried a series of commands from this thread (http://ubuntuforums.org/showthread.php?t=2187780) in an attempt to identify the problem, but at no point could I get the laptop to ever recognize the USB adapter. I have also troubleshot the USB cable itself, tried both the USB 2.0 and 3.0 ports on the laptop, have never received an error message regarding a need to update the firmware, and have seemingly successfully installed all manner of variation of Realtek drivers which were supposed to make the adapter work. (I also tried to delete/clean up after each install, in the hope I wasn't making things worse.) Not sure what I should do next. Please let me know if I need to post any more information. Thanks very much for your help. EDIT: Before inserting Alpha USB adapter: :~$ lsusb Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:570c Realtek Semiconductor Corp. Bus 001 Device 026: ID 13d3:3393 IMC Networks Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 002: ID 03f0:3112 Hewlett-Packard Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub After inserting Alpha USB adapter (USB 3.0 port, no change): :~$ lsusb Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:570c Realtek Semiconductor Corp. Bus 001 Device 026: ID 13d3:3393 IMC Networks Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 002: ID 03f0:3112 Hewlett-Packard Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Ran tail -f /var/log/syslog, inserted device, no recognition (last entry is dated 16:17:01, so an hour ago). Going to check on an Ubuntu 14.04 laptop and Windows XP desktop. I'll update after. Thanks for your help to this point.

    Read the article

  • Wireless internet works on W7 and on University Network but is extremely slow at home

    - by Rick
    I'm using ubuntu 12.04 with an Atheros wireless card. My internet speed in W7 is great. My internet speed in Ubuntu 12.04 at a university network is great. My internet speed in Ubuntu 12.04 at my home network is really slow. Some solutions I have tried but didn't work: Disabling IPv6 Running the following code: sudo ifconfig wlan0 down sudo rmmod -f iwlwifi sudo modprobe iwlwifi 11n_disable=1 sudo ifconfig wlan0 up Thanks for the help!

    Read the article

  • Slow wireless on Dell XPS 14 ultrabook

    - by GaryBishop
    I've got Ubuntu 12.04 running on this Dell XPS 14 Ultrabook (L421X). Everything is working but my wireless transfer rates are low. I'm getting about 1MB/s download speed on the ultrabook vs 15MB/s on the E6500. If I move into the room with the access point the speed climbs to 15MB/s so I'm guessing it is a signal strength issue but wavemon shows comparable signals to those seen by the E6500. Are there any settings I can tweak in hopes of making it faster?

    Read the article

  • Wireless ad-hoc network between Ubuntu and MS Windows

    - by nixnotwin
    I have setup a wireless ad-hoc connection between two laptops: one running ubuntu and the other MS XP. I have assigned static IP to both the laptops and both get connected quite easily. I can access all ubuntu services like ssh, squid, samba from the laptop running MS Windows. But from Ubuntu machine I cannot access any Windows services like shared directories etc. The Windows machine doesn't even respond to ping requests from ubuntu.

    Read the article

  • rt2800 wireless keeps disconnecting

    - by Matthew Fumi
    My HP dm1 laptop has a rt2800sta wlan driver. My wireless doesn't usually have a problem connecting to a network, yet sometimes it does. The biggest issue I have found is that when it does connect, it doesn't stay connected. It continually connects and disconnects to the network. Does anyone know why this is happening, and how I would go about fixing the issue? Thank you and look forward to trying your solutions.

    Read the article

  • No firmware found for b43 wireless controlloer (BCM4318) on a Dell Latitude D610

    - by Stanton.Sculpture
    Trying to get my 03:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) working. I just reformated and installed 12.04 on this old Windows XP machine, and I don't know where to get the firmware for this. This is what I got when I typed sudo lshw -c network: http://pastebin.ubuntu.com/1041161/ Also, when I go to additional drivers in the system settings, no proprietary drivers show up. Any help I can get on this would be Great, Thanks!

    Read the article

  • installed ubuntu 12.04 and no wireless internet at all

    - by Memoq
    I'm extremely new to ubuntu. I installed 12.04 on a laptop that had no os. I've tried following these forums to troubleshoot my internet problems only to be confused by all the steps. I need help. I'm willing to follow any instruction as long as they make sense. Any help would be nice. The equipment i have is a Dell inspiron 1100 laptop wireless card is D link 2.4 dwl -g650 product ar5212/ar5313

    Read the article

  • Looking for wireless product

    - by Belinda
    Can anyone suggest some options for me? I would like to provide our maintenance department with a view-only monitor showing our common Outlook calendars. I'm guessing it would have to have some touch-screen capabilities since they would need to be able to toggle between several calendars. We do have a cobbled together, building wide wireless network. I don't want anything that needs to be "wired or cabled" just plugged into a power source and mounted on the wall.

    Read the article

  • Broadcom device 4365 wireless driver for 12.04

    - by NilPointer
    My laptop (Dell Inspiron 17R 5720) came with preinstalled Ubuntu 11.10. I removed it and installed 12.04. Now I can't find driver for wireless. Apparently, in 11.10 there was Broadcom-STA driver. But in 12.04 there is no additional drivers to install. I tried using: sudo m-a a-i broadcom-sta But building fails on 26%. How can I install driver According to lspci i got: Broadcom Corporation Device 4365 (rev 01)

    Read the article

  • LXC container can only access host via bridge

    - by vitaut
    I have an LXC container with i686 Ubuntu 12.04 running on a x86_64 Ubuntu 12.04 host. I've set up a bridge using instructions here. However the ping from the container only goes through to the host and not to other machines on the local network. Similarly only the host and not the other machines see the container OS. The host's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback iface eth0 inet manual auto br0 iface br0 inet dhcp bridge_ports eth0 bridge_fd 0 bridge_maxwait 0 The container's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp And here's the relevant part of the container's config: lxc.network.type=veth lxc.network.link=br0 lxc.network.flags=up Any ideas what I'm doing wrong? Additional info: The output of iptables-save on host: $ sudo iptables-save # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *filter :INPUT ACCEPT [6854:721708] :FORWARD ACCEPT [4067:538895] :OUTPUT ACCEPT [4967:522405] COMMIT # Completed on Sat Oct 26 06:06:48 2013 # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *nat :PREROUTING ACCEPT [82235:21547307] :INPUT ACCEPT [16:1070] :OUTPUT ACCEPT [9386:583359] :POSTROUTING ACCEPT [14693:1291952] -A POSTROUTING -s 10.0.3.0/24 ! -d 10.0.3.0/24 -j MASQUERADE COMMIT # Completed on Sat Oct 26 06:06:48 2013 The output of brctl show on host: $ brctl show bridge name bridge id STP enabled interfaces br0 8000.080027409684 no eth0 vethBkwWyV The output of ifconfig br0 on host: $ ifconfig br0 br0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:232863 errors:0 dropped:0 overruns:0 frame:0 TX packets:59518 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34437354 (34.4 MB) TX bytes:198492871 (198.4 MB) The output of ifconfig eth0 on host: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:299419 errors:0 dropped:0 overruns:0 frame:0 TX packets:203569 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:59077446 (59.0 MB) TX bytes:372056540 (372.0 MB) The output of ifconfig eth0 on container: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:16:3e:74:08:2b inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::216:3eff:fe74:82b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:81 errors:0 dropped:0 overruns:0 frame:0 TX packets:113 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8506 (8.5 KB) TX bytes:9021 (9.0 KB)

    Read the article

  • Wireless Bridge -DHCP

    - by Usta
    I was thinking of picking up a couple of TP-Link wireless routers, and setting them to bridge. I have a sep. LAN network that would have one of them, and I'd put one on my internet connection. Would I be able to keep my current IP subnets? (255.255.255.0 and 255.0.0.0) or would I have to pull my IPs from the same IP range. (I want to keep my current DHCP servers in place) The reason I want a bridge is so that I can VPN into the internal network.

    Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >