Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 18/391 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

  • ASUS EeePC Fn+F2 ruins wireless until restart

    - by dawmail333
    I managed to get my wireless working beautifully (ath5k driver working great), and it works over a disable/enable wireless cycle, even a suspend/wakeup cycle (read some people have issues with that). Unfortunately, I discovered that if I press Fn+F2 on my keyboard (Asus EeePC 900HA, so that's the wireless toggle key), wireless then stops working until I restart the computer. How can I fix this? I'm running UNR 10.10 (with Unity turned off tyvm!). I heard something about Jupiter controlling these keys, but what about asus-laptop? How can I fix this behaviour? TIA. (Note, I'm a power user, but still fairly new to Linux. I'm picking up speed though).

    Read the article

  • Installing Broadcom Wireless Drivers

    - by Fer1805
    I'm having serious problems installing the Broadcom drivers for Ubuntu. It worked perfectly on my previous version, but now, it is impossible. What are the steps to install Broadcom wireless drivers for a BCM43xx card? I'm a user with no advance knowledge in Linux, so I would need clear explanations on how to make, compile, etc. lspci -vnn | grep Network showed: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] iwconfig showed: lo no wireless extensions. eth0 no wireless extensions.

    Read the article

  • Broadcom bcm4313 Ubuntu 13.10 connection time out

    - by Wahtever
    After upgrading to Ubuntu 13.10 I keep getting connection timed out every few seconds at which point i have to disconnect and reconnect to the WiFi network. The WiFi card worked fine on 13.04 with the bcmwl-kernel-source installed but giving problems on 13.10: *-network description: Wireless interface product: BCM4313 802.11bgn Wireless Network Adapter vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: c0:14:3d:cc:c9:c7 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.4 latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f0500000-f0503fff How can i fix this? Thanks

    Read the article

  • No Internet Connection - ubuntu 11.10

    - by emersonhsieh
    I installed Ubuntu 11.10 recently. After the first bootup the computer freezes so I have to force-quit my computer. Then I turned on my computer after that. I tried connecting to the internet. My (and my neighbor's) wireless networks shown up, but no matter how many times I tried, I can't connect to my home network. I checked the password and the other laptop's internet works (a MacBookPro). It was a wireless network. What's weird is that the Wireless network worked when I was installing ubuntu How can I connect to the internet now? I don't have a wired network. Please Help! Any help will be appreciated Specs: ASUS F81Se, Windows 7 Dual-boot, I remember the wireless card was made by Atheros, 4GB RAM

    Read the article

  • After upgrade to 12.04 wireless keeps dropping on BCM4312

    - by Sheket
    I know there are plenty of questions very similar to these, but I've tried practically everything and it still isn't working. Some solutions get the wireless connection working, but it goes very slow and drops after a few minutes. Then it won't reconnect and keeps asking for password. Hope you can help me. Thanks in advance. This is the output for sudo lshw -C network *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:f0300000-f0303fff *-network description: Ethernet interface product: AR8132 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: c0 serial: 00:23:5a:9b:6e:b1 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.0.106 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:42 memory:f0200000-f023ffff ioport:a000(size=128) *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: 00:24:2c:83:f0:81 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.2.0-30-generic firmware=478.104 link=no multicast=yes wireless=IEEE 802.11bg And for lsmod | grep b43 b43 342643 0 mac80211 436455 1 b43 cfg80211 178679 2 b43,mac80211 bcma 25651 1 b43 ssb 50691 1 b43 And for rfkill list 5: phy0: Wireless LAN Soft blocked: no Hard blocked: no

    Read the article

  • compiling compat-wireless fails at 'make' with 'make: *** [modules] Error 2'

    - by Paul Carter
    Trying to compile the compat-wireless-2012-09-25 driver module, without success. scrips/driver-select alx ; works make ; fails - scripts/Makefile.build:44 ~/sourcecode/compat-wireless-2012-09-25.2/drivers/net/ethernet/atheros/alx/Makefile: No such file or directory make[4]: ** No rule to make target '~/sourcecode/compat-wireless-2012-09-25.2/drivers/net/ethernet/atheros/alx/Makefile'. Stop. [snip] make: * [modules] Error 2 Device is Atheros AR8161 wired ethernet in a Dell Vostro 3460. I'd be very grateful for assistance in getting this to compile.

    Read the article

  • Wireless internet connection connects but internet does not work (no packets received). Wired does.

    - by Rodney
    When I connect my PC via ethernet cable to my ADSL router it works fine. When I connect via Wireless it connects and the internet will work for a random amount of time and then stop working. It stays connected with a strong signal but no packets are received. My laptop/iphone are right next to it and wireless works fine. If I open the Wireless USB status, it says it is connected to my SSID with full strength (54 mps - I am 3 meteres away from my router) and the activty shows as Packets 594 SENT and 105 RECEIVED (this goes up VERY slowly) I have tried the following: Turned off anitvirus and firewall completely. Tested the wifi signal- I am writing this on my laptop which is next to my PC and also has full wifi strength. Tried a different wireless adapter - I dug out an old PCI wireless card - it does the exact same thing. Compared all wireless settings to my laptop. I can ping google.com and it replies (sometimes with packet loss) When I reboot the PC it will connect for a minute or two (random time) and then just stops again. I tried Firefox, IE etc. no joy I have updated all latest versions (Netgear WG111v2) and drivers Checked Event Log - nothing unusual Ping the router (and even connect as admin for the few minutes when the internet does work) Changed the MTU down to 1200 using DrTCP Checked Device Manager for conflicts - none. I ping the router from the PC (192.168.0.10 - 192.168.0.1) and it replies with 4 packets. BUT, on my router admin page (which I access via http on my laptop wirelessly) - if I ping 192.168.0.10 all packets timeout (pinging my laptop 192.168.0.12 works fine) My router admin page shows the leased IP address for 192.168.0.10 (ie it is definitely talking to the router initially) Now I am out of ideas - please help. I think it is an OS/Software issue as I have tried 2 different wireless adapaters (PCI and USB) with the same result but all other wireless devices work fine around mine). It's not the firewall. It is getting assigned an IP address correctly (my PC gets 192.168.0.10, my laptop is .12) It is assigned by DHCP. As soon as I plug in the ethernet cable it all works fine. Repairing the adapter sometimes helps but it will always stop working after a random time. The wireless adapter always shows as connected with Excellent signal but the internet does not work. I am running Windows XP SP3 and have tried a Netgear WG111v2 USB adapter. Thanks in advance! UPDATE: The internet seems to be working, it is just either sending packets too small or slow to work (some small pages load bits of them very slowly but then hang). XP seems to have a networking diagnostic app - here is the output: Last diagnostic run time: 08/30/10 08:16:38 IP Configuration Diagnostic Invalid IP address info Valid IP address detected: 192.168.0.10 IP Layer Diagnostic Corrupted IP routing table info The default route is valid info The loopback route is valid info The local host route is valid info The local subnet route is valid Invalid ARP cache entries action The ARP cache has been flushed Gateway Diagnostic Gateway info The following proxy configuration is being used by IE: Automatically Detect Settings:Disabled Automatic Configuration Script: Proxy Server: Proxy Bypass list: info This computer has the following default gateway entry(ies): 192.168.0.1 info This computer has the following IP address(es): 192.168.0.10 info The default gateway is in the same subnet as this computer info The default gateway entry is a valid unicast address info The default gateway address was resolved via ARP in 1 try(ies) info The default gateway was reached via ICMP Ping in 1 try(ies) info TCP port 80 on host 65.55.12.249 was successfully reached info The Internet host www.microsoft.com was successfully reached info The default gateway is OK DNS Client Diagnostic DNS - Not a home user scenario info Using Web Proxy: no info Resolving name ok for (www.microsoft.com): yes No DNS servers DNS failure HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Passive): Successfully connected to ftp.microsoft.com. info HTTP: Successfully connected to www.microsoft.com. warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out error Could not make an HTTPS connection. info Redirecting user to support call WinSock Diagnostic WinSock status info All base service provider entries are present in the Winsock catalog. info The Winsock Service provider chains are valid. info Provider entry MSAFD Tcpip [TCP/IP] passed the loopback communication test. info Provider entry MSAFD Tcpip [UDP/IP] passed the loopback communication test. info Provider entry RSVP UDP Service Provider passed the loopback communication test. info Provider entry RSVP TCP Service Provider passed the loopback communication test. info Connectivity is valid for all Winsock service providers. Wireless Diagnostic Wireless - Service disabled Wireless - User SSID action User input required: Specify network name or SSID Wireless - First time setup info The Wireless Network name (SSID) to which the user would like to connect = RodSof Wifi. Wireless - Radio off info Valid IP address detected: 192.168.0.10 Wireless - Out of range Wireless - Hardware issue Wireless - Novice user Wireless - Ad-hoc network Wireless - Less preferred Wireless - 802.1x enabled Wireless - Configuration mismatch Wireless - Low SNR Network Adapter Diagnostic Network location detection info Using home Internet connection Network adapter identification info Network connection: Name=Local Area Connection 2, Device=Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC, MediaType=LAN, SubMediaType=LAN info Network connection: Name=Wireless USB, Device=NETGEAR WG111v2 54Mbps Wireless USB 2.0 Adapter, MediaType=LAN, SubMediaType=WIRELESS info Both Ethernet and Wireless connections available, prompting user for selection action User input required: Select network connection info Wireless connection selected Network adapter status info Network connection status: Connected HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Active): Successfully connected to ftp.microsoft.com. warn HTTP: Error 12007 connecting to www.microsoft.com: The server name or address could not be resolved warn HTTP: Error 12002 connecting to www.hotmail.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out error Could not make an HTTP connection. error Could not make an HTTPS connection.

    Read the article

  • What is your best travel (portable) WiFi router?

    - by Sorin Sbarnea
    I'm looking for a small WiFi router that I could use to create my own wireless network when I travel. I'm also interested in a router that has very good signal/antenna and that is easy to take with you. Please do not recommend products just because you can find them on the net, I'm interested about personal experience. Also it's good to know if you can install open-source firmware on it. Selection criteria: size signal quality price Required: to support both 110V/220V power supply, best if embedded or retractable cord.

    Read the article

  • Router to WIFI Client to Router (New solution for distance when repeater doesnt help)

    - by Kangarooo
    Ethernet to TL-WR340G with WIFI enabled Using TL-WA500 tried repeater mode which was not good enough and had password problems (could not connect if using either ASCII or Normal password in one way then in repeater worked other way) and also could not forward (repeat) WPA/WPA2 security. So since this repeater can also be as client, I made it as client and used another router (TL-WR740N) to get from wire connection from that client and all was working for a little bit. Every machine is set up to be auto DHCP. 1st when setting up client mode I found it working after doing reset. Then after some tens of minutes internet stopped working. When I removed WiFi client then all went back to normal. Where is the problem and how to make this work? Ethernet- TL-WR340G(AutoDHCP) ==> wifi ==> TL-WA500 TL-WA500 wifi client mode(AutoDHCP) ==> wire ==> TL-WR740N TL-WR740N router mode (AutoDHCP) ==> My Computer In other words: TL-WR340G ) ) ) ) TL-WA500 ===== TL-WR740N ==== PC1 ) ) WiFi === Wire

    Read the article

  • Frequent and weird wifi disconnections

    - by Sidou
    How would you explain, troubleshoot (and solve) the following problem? Wifi ADSL modem router D-link 2640R installed in living room at about 1.8m height. Working fine, synchronising and getting/serving stable internet connection. First situation: -Laptop 01 in other end of the house, let's say in room01 southern to the living room, distant by about 15m. Getting stable signal of good to very good quality. No disconnection. -Laptop 02 in room02 opposite to room01 (5m West) which makes it almost at the same distance and direction from the router located 15m North. Getting stable signal of good to very good quality. No disconnection. Second situation: -Laptop 01 moved to room03 Northern to the living room (actually just 3m behind the wall where the router lies). Getting stable signal of excellent quality. No disconnection. -Laptop 02 still in room02 but now experiences frequent disconnections (actually almost impossible to get the Internet even though the signal level is still very good. Either no Internet with the wifi icon appearing connected to access point or no connection established at all which happens every 2 minutes and that means virtually no Internet at all as I can just get a timeframe of 1 minute or so to load any website or even get to the router's web based control panel. If Laptop 01 is completely shut down or its wifi adapters shut down or even still working but its wifi MAC address forbidden, then Laptop 02 has no problem at all. If Laptop 02 is moved to a nearer location to the router, in the living room for instance, then no connection problem occurs even if Laptop 01 is also connected. And also if we move back Laptop 01 to its original location (room 01), then no problem as well. I'm completely lost and don't know how to address this issue. I tried to change the Wifi channel and even tried the auto channel scan but that didn't solve it. I know that the problem is probably coming from Laptop 01 being in its new location or some sort of interference as the problem occurs only under the described condition but I have no idea how to solve it! I also scanned the neighborhood for wifi jam using InSSIDer, there are few other access points but they don't seem to affect the situation. Any ideas about the steps to follow or tools to use ?

    Read the article

  • How to connect to internet 2 or more pcs with an usb wifi adapter

    - by bhaoahd
    In one pc I have an USB Wifi adapter (Realtek RTL8187L Chipset), from there a 10 meters cable to an outdoor antenna. With that I connect to a public Access Point. Now I want to be able to connect more computers to internet using that same connection that comes from the outdoor antenna, what options do I have to do this? I do have another usb wifi adapter with a small omni antenna, and a router encore ENHWI-G/A. This router can be used as a Wifi AP, but it needs a modem that works with the RJ45 connector. Is there a way I could take internet from the outdoor antenna, and create another AP indoor using that router to "repeat" that wifi that comes from the outdoor antenna? If creating this second AP is not possible, should I use some sort of local network between computers, connect my main PC with the outdoor antenna, and share the connection through the lan? (I would really prefer to have a second AP indoor so I can connect other devices like a Palm, but I am not sure how could this be possible with this router and the usb wifi adapter)

    Read the article

  • Is it better to use a crowded 2.4GHz Wi-Fi channel 1, 6, 11 or "unused" 3, 4, 8, or 9?

    - by Luke
    I understand that 2.4GHz Wi-Fi channels overlap, and that the only non-overlapping channels in the US are 1, 6, and 11. Generally, my signal strength on channels 1, 6, and 11 are much stronger than my neighbors' on the same channel. However, several of the channels may have 4 or 5 others on that same channel. In this scenario, is it better to use 3, 4, 8, or 9? Or is it better to use the crowded channels 1, 6, and 11? As a secondary question, does it even matter that my signal strength is much higher than theirs? Related: Why use wifi channels other than 1, 6 or 11?

    Read the article

  • Unable to either locate any wireless networks nor even connect to wifi

    - by Leo Chan
    I'm new to Linux. I currently have installed ubuntu 12.10. I had a previous problem with my wireless card (see url to see previous problem : How to enable wireless in a Fujitsu LH532?). It now shows Connect to hidden network and create new wireless network but now unfortunately it simply cannot find any wireless connections. I did have a very thorough look around about this problem such as wait a little longer since sometimes it cannot load all the wireless connections available that quickly. My wifi is a hidden network and I have used the connect to hidden network feature but it keeps asking for my wep key which has been checked 4 times (I counted) and it still seems to not work; It keeps asking for the WEP key. I did try both WEP 40/128-bit key and WPA & WPA2 since previously on my windows it worked; My family later decided to use WEP. I only have a quick fix using a usb wireless stick and I wish to have a more solid fix. Thanks Results from sudo iwlist wlan0 scan wlan0 Scan completed : Cell 01 - Address: 00:1E:73:C8:62:BD Channel:6 Frequency:2.437 GHz (Channel 6) Quality=25/70 Signal level=-85 dBm Encryption key:on ESSID:"EnigmaHome" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000cb3bb10a5c Extra: Last beacon: 696ms ago IE: Unknown: 000A456E69676D61486F6D65 IE: Unknown: 010482848B96 IE: Unknown: 030106 IE: Unknown: 0706484B20010B1E IE: Unknown: 2A0107 IE: Unknown: 32080C1218243048606C IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00 Cell 02 - Address: C8:3A:35:34:C1:60 Channel:6 Frequency:2.437 GHz (Channel 6) Quality=22/70 Signal level=-88 dBm Encryption key:on ESSID:"Tenda" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s 18 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 12 Mb/s; 24 Mb/s; 48 Mb/s Mode:Master Extra:tsf=000001336e70ffdd Extra: Last beacon: 716ms ago IE: Unknown: 000554656E6461 IE: Unknown: 010882848B961224486C IE: Unknown: 030106 IE: Unknown: 32040C183060 IE: Unknown: 0706434E20010D10 IE: Unknown: 33082001020304050607 IE: Unknown: 33082105060708090A0B IE: Unknown: DD270050F204104A0001101044000101104700102880288028801880A880C83A3534C160103C000101 IE: Unknown: 050400010000 IE: Unknown: 2A0106 IE: Unknown: 2D1AEC0117FFFF0000000000000000000000000000000C0000000000 IE: Unknown: 3D1606000500000000000000000000000000000000000000 IE: Unknown: 7F0101 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Preauthentication Supported IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00 IE: Unknown: 0B05010089127A IE: Unknown: DD1E00904C33EC0117FFFF0000000000000000000000000000000C0000000000 IE: Unknown: DD1A00904C3406000500000000000000000000000000000000000000 IE: Unknown: DD07000C4304000000 Cell 03 - Address: 00:1E:73:C8:62:BF Channel:6 Frequency:2.437 GHz (Channel 6) Quality=47/70 Signal level=-63 dBm Encryption key:on ESSID:"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000cb3bac614e Extra: Last beacon: 1064ms ago IE: Unknown: 00110000000000000000000000000000000000 IE: Unknown: 010482848B96 IE: Unknown: 030106 IE: Unknown: 050C010200000000000000000000 IE: Unknown: 0706484B20010B1E IE: Unknown: 2A0107 IE: Unknown: 32080C1218243048606C IE: Unknown: DD070050F202000100

    Read the article

  • Wireless Network Found, can't connect, repeated requests for authentication

    - by Herm Holland
    After trawling through the internet, on forums, support websites, and through dozens upon dozens of answered questions on this site, I've not found a solution to what seems like a fairly regular problem... I cannot connect to a wireless network, and am continually asked for the network password. I have tried countless suggested solutions on the different locations I've already referred to. None of them have worked. Details of my experience are as follows: I have just recently installed Ubuntu 12.04.1 (32-bit). Ubuntu installed on my system seemingly fine, and I even formatted my hard drive during the process. It's as if it were a new desktop computer. During the installation I was asked to connect to a Wireless Network. I have a USB Wireless Card connected which I have used to connect desktop PC's, laptops, and a Wii to the internet from approximately the same area of the house (thus the same distance from the Wireless Router). I chose my network, entered the correct password for it (I double checked; it's definitely the right password) and proceeded with the installation. Several times before the installation was complete, I was asked to authenticate the connection, and this seemed to do nothing each time. On the repeated screens the password was already entered in the appropriate box. When Ubuntu booted up the first thing I was faced with (other than something about Language settings, or something) was another request for authentication. Again, the password was already there, so I clicked connect. It did not connect. Instead, I was once again faced with repeated requests every few minutes. I went onto my laptop, which is connected to this network, checked the details of the network, and entered them manually into my Ubuntu PC (including the IPv4 and IPv6 information) but this didn't work either, so I set it back to finding the settings automatically. Note, also, that the "Connect automatically" and "Available to all users" boxes are checked, and have been unchecked & rechecked countless times. I have also tried having my User account connect automatically, and to need a password entered at the welcome screen. Whilst I've been writing this, it has gone through a spat of connecting successfully to the network for less than a minute, before coming offline again, only to repeat the process. But it has now returned to prompting me for a password every couple of minutes. This computer has already run on the Fedora OS, and had no trouble connecting to, and maintaining a connection. I also have a laptop running Windows 7 less than a metre away from this desktop PC, which is connected and has no trouble maintaining a connection at 50%-100% strength (fluctuating). Therefore: - I know it's not the wireless card - I know it's not the PC itself - I know it's not the access point - I know it's not the location of my PC or wireless card - It is solely because of Ubuntu Everything else has worked fine, but the moment Ubuntu was introduced into the equation, it has gone completely wrong. Honestly; I prefer Ubuntu as an OS to Fedora, but if I can't solve the problem it'll be straight back to Fedora that I'll have to go. Can anyone help me at all?

    Read the article

  • Randomely loosing wireless connexion with Cubuntu 12.04

    - by statquant
    I am presently experiencing random disconnections from my wireless network. It looks like it is more and more frequent (however I have not seen any clear pattern). This is killing me... Here is some information that should help (from ubuntu forums). Thanks for reading Machine : Acer Aspire S3 statquant@euclide:~$ lsb_release -d Description: Ubuntu 12.04.1 LTS statquant@euclide:~$ uname -mr 3.2.0-33-generic x86_64 statquant@euclide:~$ sudo /etc/init.d/networking restart * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... statquant@euclide:~$ lspci 02:00.0 Network controller: Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01) statquant@euclide:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 004: ID 064e:c321 Suyin Corp. Bus 002 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. statquant@euclide:~$ ifconfig wlan0 Link encap:Ethernet HWaddr 74:de:2b:dd:c4:78 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::76de:2bff:fedd:c478/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:913 errors:0 dropped:0 overruns:0 frame:0 TX packets:802 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:873218 (873.2 KB) TX bytes:125826 (125.8 KB) statquant@euclide:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"Bbox-D646D1" Mode:Managed Frequency:2.437 GHz Access Point: 00:19:70:80:01:6C Bit Rate=65 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=56/70 Signal level=-54 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:71 Missed beacon:0 statquant@euclide:~$ dmesg | grep "wlan" [ 17.495866] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 17.498950] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 20.072015] wlan0: authenticate with 00:19:70:80:01:6c (try 1) [ 20.269853] wlan0: authenticate with 00:19:70:80:01:6c (try 2) [ 20.272386] wlan0: authenticated [ 20.298682] wlan0: associate with 00:19:70:80:01:6c (try 1) [ 20.302321] wlan0: RX AssocResp from 00:19:70:80:01:6c (capab=0x431 status=0 aid=1) [ 20.302325] wlan0: associated [ 20.307307] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 30.402292] wlan0: no IPv6 routers present statquant@euclide:~$ sudo lshw -C network [sudo] password for statquant: *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 74:de:2b:dd:c4:78 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-33-generic firmware=N/A ip=192.168.1.3 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c0400000-c047ffff memory:afb00000-afb0ffff statquant@euclide:~$ iwlist scan wlan0 Scan completed : Cell 01 - Address: 00:19:70:80:01:6C Channel:6 Frequency:2.437 GHz (Channel 6) Quality=56/70 Signal level=-54 dBm Encryption key:on ESSID:"Bbox-D646D1" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000125fb152bb Extra: Last beacon: 40020ms ago IE: Unknown: 000B42626F782D443634364431 IE: Unknown: 010882848B960C121824 IE: Unknown: 030106 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101820003A4000027A4000042435E0062322F00 IE: Unknown: 2D1A4C101BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D1606080800000000000000000000000000000000000000 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000 And... finally, please note that I did the following (after looking for fixes of similar problems), but unfortunately it did not work sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1

    Read the article

  • Can I use an Apple AirPort Express as a wireless-to-wired bridge?

    - by Chris
    I have a wireless network using an Apple AirPort Extreme. That device is set up in my office and hooked up to the cable modem. I have a TV in another room which can accept a wired internet connection (not wireless enabled). Can I use an Apple AirPort Express's ethernet jack to create a wireless-to-wired bridge? If not, what device would I use to do the same thing?

    Read the article

  • Wifi disabled for Intel Centrino Wireless-N 1000 Intel in 12.04

    - by new_bie
    Laptop model - HP- dm4 - 2070. I had faced the same problem for wireless being disabled in case of 11.10. It had to do with the new kernel. I thought with 12.04 this problem will be handled but the problem persists. Is there no way to get the wireless working except for the way mentioned in the following link ?? Wifi for Centrino Wireless-N 1000 Intel Corporation (HP pavillion dm4 - 2070us) is not working Output for sudo lshw -class network *-network UNCLAIMED description: Network controller product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress cap_list configuration: latency=0 resources: memory:c2500000-c2501fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: c0 serial: 2c:41:38:07:f3:e3 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.116 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:c1400000-c143ffff ioport:2000(size=128) Output for dmesg | grep iwl [ 14.742886] iwlwifi 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 14.742897] iwlwifi 0000:01:00.0: setting latency timer to 64 [ 14.743013] iwlwifi 0000:01:00.0: pci_resource_len = 0x00002000 [ 14.743016] iwlwifi 0000:01:00.0: pci_resource_base = ffffc90000c78000 [ 14.743018] iwlwifi 0000:01:00.0: HW Revision ID = 0x0 [ 14.743119] iwlwifi 0000:01:00.0: irq 42 for MSI/MSI-X [ 14.743161] iwlwifi 0000:01:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 14.743229] iwlwifi 0000:01:00.0: L1 Enabled; Disabling L0S [ 14.765147] iwlwifi 0000:01:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 14.765151] iwlwifi 0000:01:00.0: Device SKU: 0X50 [ 14.765154] iwlwifi 0000:01:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 14.765907] iwlwifi 0000:01:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 14.912840] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-5.ucode' failed. [ 14.914254] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-4.ucode' failed. [ 14.915718] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-3.ucode' failed. [ 14.916986] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-2.ucode' failed. [ 14.919391] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-1.ucode' failed. [ 14.919445] iwlwifi 0000:01:00.0: no suitable firmware found! [ 14.919783] iwlwifi 0000:01:00.0: PCI INT A disabled [ 2868.960807] Modules linked in: snd_hda_codec_hdmi snd_hda_codec_idt rfcomm bnep bluetooth parport_pc ppdev binfmt_misc hid_logitech_dj usbhid hid joydev snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq hp_wmi sparse_keymap hp_accel lis3lv02d input_polldev snd_timer snd_seq_device wmi iwlwifi snd mac80211 i915 cfg80211 rts_pstor(C) drm_kms_helper drm uvcvideo videodev psmouse soundcore mei(C) v4l2_compat_ioctl32 mac_hid serio_raw snd_page_alloc i2c_algo_bit video lp parport atl1c

    Read the article

  • Wireless connection by using command screen

    - by Amadeus
    I installed Ubuntu 12.04 armhf to my beagleboard-xm and now trying to connect to a wireless network. First, I checked if I can search for available networks: ubuntu@arm:~$ iwlist scan lo Interface doesn't support scanning. usb0 Interface doesn't support scanning. wlan0 Scan completed : Cell 01 - Address: EA:7D:EF:60:C9:0B Channel:1 Frequency:2.412 GHz (Channel 1) Quality=70/70 Signal level=-23 dBm Encryption key:on ESSID:"ghostrider" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Ad-Hoc Extra:tsf=000000005a1ab50e Extra: Last beacon: 6242ms ago IE: Unknown: 000A67686F73747269646572 IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 06020000 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: Unknown: 32040C121860 IE: Unknown: 2D1A2C181BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D16010800000000FF000000000000000000000000000000 IE: Unknown: DD09001018020000000000 Then I edited /etc/network/interfaces file to the following: root@arm:/etc/wpa_supplicant# cat /etc/network/interfaces auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # Example to keep MAC address between reboots #hwaddress ether DE:AD:BE:EF:CA:FE # WiFi Example auto wlan0 iface wlan0 inet dhcp wpa-ssid "ghostrider" wpa-psk "b34d373eb2fb836a43b0afffe783c7d0af694724506c9e77b06d1021302905bf" But I cannot still connect to the wireless network: root@arm:/etc/wpa_supplicant# iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Asociated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on eth0 no wireless extensions. root@arm:/etc/network# ifup wlan0 Failed to bring up wlan0. What is wrong? Should I change any other files also? But I think it was enough. By the way if you are curious about where that wpa-psk came from: zero@ghostrider:~$ wpa_passphrase ghostrider 34bddf67c2 network={ ssid="ghostrider" #psk="34bddf67c2" psk=b34d373eb2fb836a43b0afffe783c7d0af694724506c9e77b06d1021302905bf } I will appreciate any effort to help. Regards, Amadeus ps: Also I tried to connect manually: root@arm:/etc/network# iwconfig wlan0 essid ghostrider key s:34bddf67c2 But this did not solve my problem also.

    Read the article

  • kubuntu: wireless manager can't find any networks

    - by timuçin
    I just installed Kubuntu 12.10 and as I knew my wireless driver would not be recognized, I installed it manually through here. I suppose I shall mention that I also had to do this. The driver worked just fine until I restarted my system. Since then I can't even start over. My wireless card is realtek 8723 The oly lead I have is this piece of log: 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <info> wpa_supplicant started 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <info> (wlan0) supports 4 scan SSIDs 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <info> (wlan0): supplicant interface state: starting -> ready 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <info> (wlan0): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42] 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <warn> Trying to remove a non-existant call id. 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <info> (wlan0): supplicant interface state: ready -> inactive 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <info> (wlan0) supports 4 scan SSIDs I feel really bad that I have been trying so many things and even while I am trying them I get a problem at every step. I am really frustrated. You can the time in the logs, I didn't get up early. Just needed to share my feelings. Even the ethernet cable I have use is short for God's sake, I have had to sit at this massively uncomfortable posture for hours. edit: I discovered something interesting. When I boot my windows I see that my wireless manager says "disconnected" now. However when I start ubuntu after windows and modprobe rtl8723e wireless works just fine. Then again, when I restart ubuntu I am back where I have started. So now I have to start windows, restart my machine and do the modprobe thing to see wireless networks.

    Read the article

  • Toshiba wireless is blocked

    - by zorrillo
    I have the same problem, a 32 bits toshiba nb255, it first had the windows 7 bu next I installed the ubuntu 11.04. The wifi does not turn on. I used the following issues the commands rfkill unblock wlan0, sudo ifconfig wlan0 down; they were not able. by setting up the bios in advanced menu, the wireless communication sw in ON, but it did not work also. neither the utilities toshiba nor utilities of ubuntu (wicd, wifi radar). by using gedit to file group, nothing. by installing madwifi packet, nothing. by exporting the wifi driver from windows to ubuntu, by means of the NDISwrapper packet, neither. I put the current scripts of the ouput of the cli root@zorrillo:~# rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes root@zorrillo:~# sudo lspci | grep Atheros 07:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) root@zorrillo:~# root@zorrillo:~# ifconfig -a eth0 Link encap:Ethernet direcciónHW 88:ae:1d:47:df:e1 ACTIVO DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) Interrupción:43 Dirección base: 0xe000 lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:16436 Métrica:1 Paquetes RX:8 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:8 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:480 (480.0 B) TX bytes:480 (480.0 B) ppp0 Link encap:Protocolo punto a punto Direc. inet:189.203.115.236 P-t-P:192.168.226.1 Másc:255.255.255.255 ACTIVO PUNTO A PUNTO FUNCIONANDO NOARP MULTICAST MTU:1500 Métrica:1 Paquetes RX:6384 errores:30 perdidos:0 overruns:0 frame:0 Paquetes TX:6893 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:3 Bytes RX:5473081 (5.4 MB) TX bytes:974316 (974.3 KB) wlan0 Link encap:Ethernet direcciónHW 00:26:4d:c3:d0:44 DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) note.-it is logical all the counters are cero if the wireless device is down root@zorrillo:/home/zorrillo/Descargas/802BGA# ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill root@zorrillo:/home/zorrillo/Descargas/802BGA# It would seem the wireless switching does not react with whichever ubuntu 11.04 command (I hope to be wrong). The target remains the same, in order of the scripts above. I am worried, I have tried to find any answer for days and nights. Toshiba does not supply drivers or soft support for linux, marketing of course. I only see the device is up by protocols and down phisically, My question is, is it possible to enable or not shutdown physically the device?, because in the toshiba model nb255 the wifi is not set up/down bye means of a physical switch, but by means a combination of Fn + F8 (only for windows 7, no one more), Is there one possibility to configure the hot keys in ubuntu?

    Read the article

  • (Solved) ERROR: Packet source 'wlan0' failed to set channel 2: mac80211_setchannel() in Kismet and Ubuntu 12.10

    - by M. Cunille
    I have installed Ubuntu 12.10 in my computer with an Atheros AR5007 wireless card. I want to use Kismet but when I run it it starts displaying the message: ERROR: Packet source 'wlan0' failed to set channel X: mac80211_setchannel() It keeps displaying the same for every channel except channel 1. I have installed the compat-wireless-3.6.6-1 drivers and patched them with the following patch in order to use them with aircrack-ng. I have installed the latest version of Kismet in the git repository and I even tried with the svn but it keeps displaying the same error. I also have set the kismet.conf file with the nsource=wlan0 as it is the name of my wireless interface according to iwconfig : lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:"XXXX" Mode:Managed Frequency:2.412 GHz Access Point: XX:XX:XX:XX:XX:XX Bit Rate=18 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=28/70 Signal level=-82 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:282 Missed beacon:0 I haven't found any answer since similar errors are supposed to be fixed with the latest Kismet release but this isn't my case. Any help will be appreciated. Thank you!

    Read the article

  • Atheros wireless not working

    - by Chandru1
    I have been struggling hard since i have installed Ubuntu 10.10 but it has been difficult for me to get my wifi working. So here is what i tried. First i checked whether i have the driver using the ifconfig command and it shows the wireless lan driver as wlan0. Next, i tried the command iwlist wlan0 scanning by becoming the root which gave me the output as no scan results. Next, i visited this link https://help.ubuntu.com/community/WifiDocs/Driver/Atheros to see as to what problem my laptop may have. I do own have an ath5k chipset. And as i followed the instructions in the above link in one of the blacklist-ath_pci.conf file had this written in it. For some Atheros 5K RF MACs, the madwifi driver loads buts fails to correctly initialize the hardware, leaving it in a state from which ath5k cannot recover. To prevent this condition, stop madwifi from loading by default. Use Jockey to select one driver or the other. (Ubuntu: #315056, #323830 I am not that good at Linux but i have given it a try. I am desperate to have my wifi working and i would be glad if this community could help. ADDED: If anyone would like to know as to what drivers i am using this is the output. network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wlan0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath5k driverversion=2.6.35-24-generic firmware=N/A latency=168 link=no maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11bg resources: irq:18 memory:d0000000-d000ffff Some more information and output as to what i have done. lsmod | grep ath ath5k 130083 0 mac80211 231541 1 ath5k ath 8153 1 ath5k cfg80211 144470 3 ath5k,mac80211,ath led_class 2633 1 ath5k

    Read the article

  • How to get Broadcom BCM 43XX Wireless card working

    - by Fer1805
    NOTE - Although this question is for a specific version of Ubuntu and a specific Broadcom model, the answer to it is for most Broadcom models and versions of Ubuntu 11.04, 11.10, 12.04 and 12.10. If you have come here from another question, feel free to read the answer instead. The answer covers many problems with several solutions. I'm having serious problems installing the Broadcom drivers for Ubuntu 11.04. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. I was following the instructions on the following blog, with no luck. How can I get Broadcom BCM4311 Wireless working? Can someone help me? Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. hope above info is enough for your help.

    Read the article

  • How do I install windows wireless driver for TP-Link TL-WN7200ND

    - by Jim
    I'm using the TP-Link TL-WN7200ND USB wireless adapter. I have downloaded the Windows drivers and updated Ubuntu to 10.10 by manually connecting the computer to the router. I also installed ndiswrapper-gtk. I get a Windows Wireless Drivers in my Administration menu, and I was able to get it to read the Windows 7 .inf file. The .inf for XP does not work. It adds it and the driver appears in the list with "Hardware: present". I set up the wireless connection information (ESSID and WPA2-Personal key). Problem: I don't see the network manager icon in the top right of the screen. I managed to manually start it manually using sudo services network-manager restart but it shows no connections in the menu, saying that there's nothing to manage. In my /etc/network/interfaces file I have an entry for the loopback and the standard two-liner for eth0 with dhcp. From memory, something like: iface eth0 auto eth0 dhcp I had read somewhere that 10.10 would have standard support for my wireless adapter (TL-WN7200ND) but that seems not to be the case. However, I don't ever remember having the network-manager icon in the top-right and it does not auto-start at the moment. This was originally an Ubuntu 9.10 install that I've upgraded over time. I also used to use pppoeconf to connect to the net, which might affect the /etc/network/interfaces file?

    Read the article

  • Frequent disconnects with oneiric server using wlan AR9285

    - by John Neil
    I'm getting a large number of disconnects from my wireless when I switched to oneiric server (I did not see these happen with oneiric desktop) from my AR9285 wireless LAN device. Here is the syslog snippet: Oct 17 09:43:17 weather kernel: [ 1537.329138] wlan0: deauthenticated from 00:12:17:7a:8e:42 (Reason: 7) Oct 17 09:43:17 weather kernel: [ 1537.340409] cfg80211: All devices are disconnected, going to restore regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340423] cfg80211: Restoring regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340435] cfg80211: Calling CRDA to update world regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348571] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348581] cfg80211: World regulatory domain updated: Oct 17 09:43:17 weather kernel: [ 1537.348586] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Oct 17 09:43:17 weather kernel: [ 1537.348594] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348600] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348607] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348613] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348620] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Here is the relevant lspci output: # lspci | grep Atheros 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) I have done quite a bit of searching and saw discussions for previous versions of ubuntu that recommended installing the linux-backports-modules package. However, this does not appear to be available for oneiric (just the headers are listed as a package). Any advice on how to achieve a stable wireless connection for this server? It's location mitigates against using a wired connection.

    Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >