Search Results

Search found 27258 results on 1091 pages for 'installed programs'.

Page 180/1091 | < Previous Page | 176 177 178 179 180 181 182 183 184 185 186 187  | Next Page >

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• User directive in nginx generates error despite running as UID root

  - by Joost Schuur

  I'm running nginx on a MacOS X machine, installed with brew, and when I launch nginx, even with sudo, I get the following warning in my log file over and over again: 4/21/11 2:03:42 AM org.nginx[3788] nginx: [warn] the "user" directive makes sense only if the master process runs with super-user privileges, ignored in /usr/local/etc/nginx/conf/nginx.conf:2 From nginx.conf: user jschuur staff; I'm already launching nginx with sudo, since I want the thing to listen on port 80. Shouldn't that be enough to give it the proper super user privileges? The nginx binary as it's installed: jschuur@Glenna:sbin ? master ls -la total 4544 drwxr-xr-x 3 jschuur staff 102 Apr 12 20:53 . drwxrwxr-x 15 jschuur staff 510 Apr 12 15:25 .. -rwxr-xr-x 1 jschuur staff 2325648 Apr 12 20:39 nginx FWIW, I recompiled the binary to set passenger up and moved it around from it's original location into /usr/local/sbin. Update: As it turns out MacOS X was restarting nginx after I'd stopped it, because the launchd plist in ~/Library/LaunchAgents had set it to 'KeepAlive'. However, because I installed this plist into my local user's LaunchAgents folder as opposed to /Library/LaunchAgents (or better yet /Library/LaunchDaemons, which run before you even log on), it wasn't executed as root. Because of an error about not having permissions to use port 80, it actually exited right away, but still wrote to the same log file as the nginx process I started with sudo. I had thought the errors stemming from the automatic restart were actually coming from my manual restart via sudo. So, bottom line, problem solved. The real problem here was the homebrew instructions specifically asking you to install the plist file into an area that wouldn't allow a local site to use port 80.

  Read the article

• How can I connect integrated webcam with virtualbox

  - by Mike Stumpf

  I am trying to use a Windows XP VM for VirtualBox on my Windows 8.1 laptop. I have tried the usual attaching USB device but I get an error saying "USB device is busy with previous request". My webcam is not active in any applications and this happens after a clean reboot of the host, the guest, and VirtualBox. Here are the details: Host -HP Pavilion 17 Notebook PC (stock) -Windows 8.1 -AMD A10-5750M APU -HP Truevision HD (integrated webcam) VM I got the VM here: http://www.modern.ie/en-us/virtualization-tools VirtualBox -VirtualBox 4.3.12 installed -VirtualBox Extension pack installed -Guest additions are installed for 4.3.12 -Enable USB Controller is checked -It does not matter if enable 2.0 controller is checked or not -It does not matter if a USB device filter is set up for the webcam or not -Here is the error message: Failed to attach the USB device DDFEQ01G45BFBV HP Truevision HD [0004] to the virtual machine IE8 - WinXP. USB device 'DDFEQ01G45BFBV HP Truevision HD' with UUID {7a2e2a45-974d-482b-9b4e-9f9abbcd0ebb} is busy with a previous request. Please try again later. Result Code: E_INVALIDARG (0x80070057) Component: HostUSBDevice Interface: IHostUSBDevice {173b4b44-d268-4334-a00d-b6521c9a740a} Callee: IConsole {8ab7c520-2442-4b66-8d74-4ff1e195d2b6} I read on some VirtualBox forums that disabling USB 2.0 support in the host BIOS solved their issue but I wanted to know if there were any other ideas before I muck around in there. Thanks

  Read the article

• How to uninstall files and software from a Solid State Drive (SSD)

  - by jasondavis

  I am using a SSD drive just as a main Operation system and software drive. I have a regular spinning disk for data files. I have read that files are not REALLY deleted from a SSD drive when you "delete" them. So here is my situation and hopefully I can get some good advice. Let's say I have Windows 7 Pro x64bit installed on my 80gb Intel SSD. I then have Adobe Photoshop CS4 installed along with 50 other programs installed onto this SSD. I then decide I am done with Adobe Phjotoshop CS4 and want to remove it. I then decide I want to install another version of Adobe Photoshop and a few other software titles. Would I just do the usual, add/remove software from the windows control panel. Or if the software being removed has an "Uninstall" program to run, then run it and uninstall the software? I realize that all this WILL remove the software from Windows 7 but I am wanting to know if there is additional steps that should be taken since it is a solid state drive (SSD)?

  Read the article

• I Made Wordpress Multisite. And Now Everything Doesn't Display Properly

  - by piratepartypumpkin

  I installed Ubuntu 10.4 then I installed Bitnami LAMP stack then I installed bitnami wordpress module then I tried to make the site into a multisite by following these instructions: http://wiki.bitnami.org/Applications/BitNami_WordPress_Multisite#How_to_add_several_WordPress_Multisite_blogs_with_different_domains.3f AND http://wiki.bitnami.org/Applications/BitNami_WordPress_Multisite I can elaborate if needed: I enabled multisite in my wp-config.php file. Then I created a network using the wordpress dashboard. I was given two blocks of text to copy and paste 1 block into my wp-config.php file and one into my .htaccess file. I did that and now I get this: When I go to my mywebsite.com I get this (this was there before I switched to multisite): If I go to mywebsite.com/wordpress I get this (this used to be a functioning wordpress theme): If I click on "My Blog" it redirects to 1mywebsite.com (where the "1" came from I have no idea) If I try to login by going to mywebsite.com/wordpress/wp-login I get this: and if I enter my user and password it redirects me to mywebsite.com/wp-login.php and gives me "Not Found" The requested URL /wp-login.php was not found on this server. NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /opt/lampstack-5.3.16-0/apps/wordpress ServerName mywebsite.com ServerAlias www.mywebsite.com </VirtualHost>

  Read the article

• Where to get grub files without using grub-install

  - by Jacky

  I am in a particular situation. I have a MacBook Pro with no internal CD drive and both MacOS X (minimal setup) and Linux (my main system) is installed. During a cross-upgrade to Ubuntu 12.04 I messed up grub, so that my /boot/grub directory is basically empty. This means I can't boot Linux on the laptop anymore but only get into grub rescue. Normally this is no issue as you'd just boot from a rescue CD or USB stick, but unfortunately with a MacBook Pro this is not possible (I have reFIT installed and it attempts to boot, but it fails and the manual says that Apple's EFI firmware is not able to handle this situation). From MacOS X, however, I still have write access to the Linux partition. I've now been trying to figure out how to populate the /boot/grub folder with the necessary files, to no avail so far. The ISO image of Ubuntu 12.04 contains an EFI folder which is not what I am looking for, instead I need the normal.mod files for the grub version of Ubuntu 12.04. I do not have any other machine to set up a virtual machine of Ubuntu 12.04 to extract this from after a grub-install, so I am asking for ideas here how to solve this mess. P.S.: I installed the Linux previously when I still had a working internal CD drive. This is gone now.

  Read the article

• Disk Error on Boot (Possible boot sector issue)

  - by Choco

  I own a 4-5 year old Dell Dimension E510 with Windows XP: Media Center Edition. I have 2 drives installed: C Drive: Windows XP: Media Center Edition G Drive: 2 partitions: Windows 7 (beta) Windows XP (professional) That is also the order they are connected. The C Drive is my primary drive. When I attempt to boot the computer, the bios loading screen appears normally; the progress bar moves and it's fine. The very next page, however, supposed to be a boot choice. When I installed Windows 7 onto the G Drive in context of the C drive it added a boot selector to the C drive's boot sequence. It gives me the option of booting Windows 7 or Windows XP: Media Center Edition. However, my problem is now this: After the bios screen I previously mentioned, instead of a boot selector, I receive the following error: A disk read error occurred. Press CTRL+ALT+DEL to restart. The drive is spinning up normally. I hear no odd noises/clicks/scraping coming from it, even after disabling the other drive to listen to it carefully. According to me, it's a boot sector issue. I have never experienced this before, but maybe during a recent shutdown, Windows XP: MCE errored out and ruined the boot sector. Dilemma! I don't have the Windows XP: MCE disc, because it was installed by the factory. I have accessed the hidden partition on the drive before (you hit a key combination on the bios screen and it comes up with an interface to fix your drive). However, I don't want to reformat the drive (which is what the interface gives me the option to do). I want to possibly fix the boot sector. How can I achieve that?

  Read the article

• Azure's Ubuntu 12.0.4 fails to install PHP5

  - by Alex Kennberg

  Similar to this article from Azure themselves: http://www.windowsazure.com/en-us/manage/linux/common-tasks/install-lamp-stack/ I am trying to install PHP5 on Ubuntu 12.0.4 virtual machine. However, it fails installing the ssl-cert. $ sudo apt-get install php5 Reading package lists... Done Building dependency tree Reading state information... Done php5 is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 49 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up ssl-cert (1.0.28) ... Could not create certificate. Openssl output was: Generating a 2048 bit RSA private key ............................+++ ...................................................................................................................+++ writing new private key to '/etc/ssl/private/ssl-cert-snakeoil.key' ----- problems making Certificate Request 140320238503584:error:0D07A097:asn1 encoding routines:ASN1_mbstring_ncopy:string too long:a_mbstr.c:154:maxsize=64 dpkg: error processing ssl-cert (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: ssl-cert E: Sub-process /usr/bin/dpkg returned an error code (1) Any tips appreciated.

  Read the article

• Installing mod_pagespeed (Apache module) on CentOS

  - by Sid B

  I have a CentOS (5.7 Final) system on which I already have Apache (2.2.3) installed. I have installed mod_pagespeed by following the instructions on: http://code.google.com/speed/page-speed/download.html and got the following while installing: # rpm -U mod-pagespeed-*.rpm warning: mod-pagespeed-beta_current_x86_64.rpm: Header V4 DSA signature: NOKEY, key ID 7fac5991 [ OK ] atd: [ OK ] It does appear to be installed properly: # apachectl -t -D DUMP_MODULES Loaded Modules: ... pagespeed_module (shared) And I've made the following changes in /etc/httpd/conf.d/pagespeed.conf Added: ModPagespeedEnableFilters collapse_whitespace,elide_attributes ModPagespeedEnableFilters combine_css,rewrite_css,move_css_to_head,inline_css ModPagespeedEnableFilters rewrite_javascript,inline_javascript ModPagespeedEnableFilters rewrite_images,insert_img_dimensions ModPagespeedEnableFilters extend_cache ModPagespeedEnableFilters remove_quotes,remove_comments ModPagespeedEnableFilters add_instrumentation Commented out the following lines in mod_pagespeed_statistics <Location /mod_pagespeed_statistics> **# Order allow,deny** # You may insert other "Allow from" lines to add hosts you want to # allow to look at generated statistics. Another possibility is # to comment out the "Order" and "Allow" options from the config # file, to allow any client that can reach your server to examine # statistics. This might be appropriate in an experimental setup or # if the Apache server is protected by a reverse proxy that will # filter URLs in some fashion. **# Allow from localhost** **# Allow from 127.0.0.1** SetHandler mod_pagespeed_statistics </Location> As a separate note, I'm trying to run the prescribed system tests as specified on google's site, but it gives the following error. I'm averse to updating wget on my server, as I'm sure there's no need for it for the actual module to function correctly. ./system_test.sh www.domain.com You have the wrong version of wget. 1.12 is required.

  Read the article

• How can I find files added to the system within X minutes of a specific time?

  - by Jack W-H

  I have done a fresh install of Mac OS X Mountain Lion today on a new MacBook. Because this was a new install, when I finally got round to configuring some of my own developer things, I was surprised to find some app had installed a binary into /usr/local/bin - a single binary called galileod. Interestingly, I can't find anything online about galileod. I had only installed the bare minimum of software at this point. Looking in the file columns I can see Date Modified was 9th November 2012, but Date Added to the system was today at 17:01. It's now 10:20PM and I can't remember which software I was installing at that point. So how do I find out which other files were installed to the system within, say, 5 minutes either side of 17:01? EDIT: I found out what galileod was by running galileod --help - it is a binary used with Fitbit to communicate with the USB dongle. So that's the mystery solved - but it would still be interesting to know how to find files added within X minutes of a timeframe for future reference.

  Read the article

• CNAME redirect to Wordpress blog not working (.htaccess problem)

  - by Vincent Chan

  I have two domains hosting in two different servers: domain1.com & domain2.com I would like to forward "blog.domain1.com" to "blog2.domain2.com" which is a Wordpress blog using CNAME redirect. Before I installed Wordpress. blog.domain1.com (=redirect=) blog2.domain2.com/index.htm (working fine) The browser will keep the URL (http://blog.domain1.com) even the index.htm is on domain2.com server. However, after I installed Wordpress, the browser will change the URL to (http://blog2.domain2.com) This is my current setup: On domain1.com DNS: blog.domain1.com CNAME redirect to domain2.com on domain2.com .htaccess: Options +FollowSymLinks RewriteEngine On RewriteCond %{HTTP_HOST} ^blog\.domain1\.com RewriteRule ^(.*)$ http://blog2.domain2.com/$1 [R=301,L] on blog2.domain2.com .htaccess: DirectoryIndex index.php <IfModule mod_rewrite.c> Options +FollowSymLinks RewriteEngine On RewriteBase /blog2/ RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /blog2/index.php [L] </IfModule> blog2.domain2.com is installed under domain2.com/blog2/ All I want to do is keeping the URL (blog.domain1.com) unchanged for the whole Wordpress redirect. Thanks a lot.

  Read the article

• Fresh Install of SQL Server 2008 doesn't install managment studio. Help!

  - by Jordan S

  Ok I am running Windows 7, 64 bit. I cleaned of SQL server 2005 completely off my system leaving only SQL Compact Edition. I went here http://www.microsoft.com/downloads/details.aspx?FamilyID=01af61e6-2f63-4291-bcad-fd500f6027ff&displaylang=en and installed SQL Server 2008 Express Edition Service Pack 1. After the install, under my start bar menu all i have for SQL configuration tools are the Configuration Manager, Error and Usage Reporting and the Install Center. I don't have the SQL Managment Studio. So I went here http://www.microsoft.com/downloads/details.aspx?FamilyID=08e52ac2-1d62-45f6-9a4a-4b76a8564a2b&displaylang=en and downloaded the SQL Server 2008 Management Studio Express but when I try to install it I get a warning says This program has known compatibility issues and that I need to Install SQL Server 2008 Service Pack 1. I thought that is what I installed. So, I tried to continue running the install but I then get an error message that says Invoke or BeginInvoke can not be called on a Form before it is opened... How can I check if Service pack 1 is installed or not? What should I do?

  Read the article

• Can't login to phpMyAdmin on a WAMP server running Windows 2008

  - by Richard West

  I am setting up a new server. I have installed Apache 2.2.17, PHP 5.3.3, MySQL 5.1.53 and phpMyAdmin 3.3.8 running on a Windows 2008 (32 bit) OS. I have configured Apache and PHP so they appear to be working fine. I have created the standard test php page with the following code and everything appears to be working fine. <?php //index.php phpinfo(); ?> I also see the mySQL and mySQLi section in the above webpage, so it appears that that I have the proper extensions loaded for mySQL access. The problem that I am having centeres around myPHPAdmin. I have this installed and I can access to the login screen at http://localhost/pma I login using "root" and the password I have setup for root. After a delay of 30 seconds or so the web page goes to a blank screen, and the url is now http://localhost/pma/index.php?token= No error is ever displayed - however nothing usable is either. I have confirmed that mySQL is running by going to the command line and logging into mySQL from there. I have double checked my configuration but I am not having any luck getting this to work. I have also disabled the Windows firewall, but that did not change anything. I installed mySQL using the standard port 3306. Any advice would be greatly appreciated.

  Read the article

• Install PHP mcrypt on Red Hat 4

  - by Chris

  I'm having a very hard time getting mcrypt for PHP installed on a Red Hat 4 server. I've downloaded the rpm but it tells me: error: Failed dependencies: php-common(x86-32) = 5.4.7-2.fc18 is needed by php-mcrypt-5.4.7-2.fc18.i686 rpmlib(FileDigests) <= 4.6.0-1 is needed by php-mcrypt-5.4.7-2.fc18.i686 libc.so.6(GLIBC_2.4) is needed by php-mcrypt-5.4.7-2.fc18.i686 libltdl.so.7 is needed by php-mcrypt-5.4.7-2.fc18.i686 rtld(GNU_HASH) is needed by php-mcrypt-5.4.7-2.fc18.i686 rpmlib(PayloadIsXz) <= 5.2-1 is needed by php-mcrypt-5.4.7-2.fc18.i686 So when I try to install one of those packages, they also require another 8 packages. So I'm diving into dependency hell here. Now if I try to compile mcrypt from source, this is what I get: checking for libmcrypt - version >= 2.5.0... no *** Could not run libmcrypt test program, checking why... *** The test program failed to compile or link. See the file config.log for the *** exact error that occured. This usually means LIBMCRYPT was incorrectly installed *** or that you have moved LIBMCRYPT since it was installed. In the latter case, you *** may want to edit the libmcrypt-config script: no configure: error: *** libmcrypt was not found But I was able to install libmcrypt from an rpm packages successfully. Any suggestions? Also, I cannot use up2date as it requires an active paid account from Red Hat and since the staff has changed rather rapidly in the last year where I work, no one knows if there even was any support accounts.

  Read the article

• Where to get glib-config for Kubuntu?

  - by Carl Smotricz

  I'm trying to compile Midnight Commander on a KUbuntu 9.10 (Karmic) box with no root access. I've set up a directory under $HOME, downloaded the mc source package and various stuff required for building, such as autotools. I've unpacked the CONTENTS of all those packages into this working directory such that I have the usual ./usr, ./lib, ./etc hierarchy. I manage to get configure through a lot of tests, but I can't seem to fool it into finding glib. checking for glib-2.0... checking for glib-config... no checking for glib12-config... no checking for glib-config... no checking for GLIB - version >= 1.2.6... no *** The glib-config script installed by GLIB could not be found *** If GLIB was installed in PREFIX, make sure PREFIX/bin is in *** your path, or set the GLIB_CONFIG environment variable to the *** full path to glib-config. configure: error: Test for glib failed. GNU Midnight Commander requires glib 1.2.6 or above. My system has glib installed: /lib/libglib-2.0.so.0 /lib/libglib-2.0.so.0.2200.3 ... and I've also downloaded and unpacked the glib package into my working directory: libglib2.0-0_2.22.2-0ubuntu1_i386.deb libglib2.0-dev_2.22.2-0ubuntu1_i386.deb ... but still the elusive glib-config is nowhere to be found. It's not in any debian package for Karmic, either. So I'd appreciate any help getting over this hurdle. Please note, again, that I don't have root, so I can't just merrily apt-get stuff.

  Read the article

• Installing WinPcap on Windows 8

  - by Dave Robinson

  I know there has been lots of discussion already on installing WinPcap on Windows 8. I'm running the RTM version. I was able to install WinPcap without a hitch by using the Windows 7 compatibility mode. Since then, I've noticed that WinPcap has stopped running and is actually no longer even installed. I tried installing it again, but now it continues to tell me that WinPcap does not work with my version of Windows. Compatibility modes and admin privileges make no difference. The only thing I remember doing to my system was installed 900MBs of Windows Updates. Does anyone have any ideas about what I might do to get WinPcap installed? I've already ensured that the compatibility mode settings I changed were in effect for all users. I've already ensured that "run this program as an administrator" is checked on the compatibility tab for all users. I've also tried installing WinPcap 4.1.2 and 4.1.1. No success with either.

  Read the article

• How to send mail with PHP [migrated]

  - by roth66

  My litle problem is about mail() function in PHP, it doesnt want to send emails, to my local server, or anywhere else. I don't think that function was supposed to send mail to adresses like: [email protected]; So I've installed a mail server: hmailserver, I installed a client: dream-mail; I installed sendmaill.exe; (actually unzipped it in a folder, then in php.ini set the sendmail_path to point to it) After countless trials and errors, it still doesn't work. my system would comprise in an Apache server 2.2, and PHP (last version I think 5.3 or somehing), running on windows. And now for avoiding the usual questions (Did you make rules in your firewall etc etc), I guess I should mention, that there arent any connectivity issues, everything is set to "local" (localhost), port 25, 110, 143, are all opened, And, after a few days of fiddling with my brand new mail-server, I manage to make it work. THe Dream-mail client, has a test, trough which it would test its connections, and according to it, the SMTP AND POP3 connections are all successful, it even sends an email, for testing. SO ya, it would work. The problem, remains: PHP mail funcion. And I really need it, since on my website there's a contact form, and right now is useless. I've also checked the form it self, and seems to be alright.

  Read the article

• Dependencies problems installing openjdk on Ubuntu

  - by Rodnower

  I try to install openjdk-7-jre: sudo apt-get install openjdk-7-jre But I have dependencies problems: Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: openjdk-7-jre : Depends: openjdk-7-jre-headless (= 7u7-2.3.2a-0ubuntu0.12.04.1) but it is not going to be installed Depends: libgif4 (>= 4.1.4) but it is not installable Depends: libatk-wrapper-java-jni (>= 0.30.4-0ubuntu2) but it is not installable Recommends: libgnome2-0 but it is not installable Recommends: libgnomevfs2-0 but it is not going to be installed Recommends: ttf-dejavu-extra but it is not installable E: Unable to correct problems, you have held broken packages. This is version of Ubuntu: Ubuntu 12.04.1 LTS I completely don't know how resolve dependencies... Some one can help me? Thank you for ahead.

  Read the article

• AMD switchable graphics are not working OR I don't know how to make them work

  - by Deus Deceit

  I don't know if this is the right place for this question, but I'll give it a shot. I have a Dell Inspiron 17R 5721. It's supposed to be using switchable graphics. It has an Intel HD 4000 and a Radeon HD 8730M and I'm using windows 8. My problem is this, I Installed the drivers that dell gives me but I don't see the AMD graphics card ANYWHERE ( I do see it in device manager but not anywhere else to select and play a game using AMD). I installed the latest drivers from AMD and same thing, I can't run a game with AMD graphics card. I change the applications preferences in the Catalyst control center but even after that, games don't give me the option to select the AMD card, they list only the Intel HD 4000. Can someone tell me what I have to do to make this work? ------------------- After looking around and messing with stuff. I think.... I THINK that you don't really get the option to select a graphics card. Switchable graphics is all about switching automatically depending on application's needs. Cause when I uninstalled AMD's drivers or actually (screwed up lol) games were playing much worse. When I re-installed them, games went back to being good looking. So even if a game sees only the Intel HD 4000 graphics card windows or AMD's drivers will switch to the AMD Readeon graphics card automatically. I hope someone can verify this. Cause seriously I don't think you get to play scyrim with High graphics settings or even ultra with the Intel HD Graphics card. -------------------

  Read the article

• VSFTPD - FTP over TLS - Upload stops after exactly 82k?

  - by Redsandro

  I installed a VSFTP daemon on a CentOS server, using a RSA certificate for logging in using explicit TLS. Now, I cannot upload more than 82k. With files under that limit, there is no problem. The FTP works like a charm. But as soon as a file reaches 82k with FileZilla (81,952 bytes to be exact), the transfer will stop, and the FTP client hangs until time out is reached. FTP client console: 15:10:21 Command: STOR jquery-1.7.2.min.js 15:10:21 Response: 150 Ok to send data. 15:11:21 Error: Connection timed out 15:11:21 Error: File transfer failed after transferring 82 KB in 60 seconds /var/log/vsftpd.log FTP command: Client "x.x.x.x", "STOR jquery-1.7.2.min.js" FTP response: Client "x.x.x.x", "150 Ok to send data." OK UPLOAD: Client "x.x.x.x", "jquery-1.7.2.min.js", 81952 bytes, 1.32Kbyte/sec FTP response: Client "x.x.x.x", "226 File receive OK." // NOT okay, file is bigger // No mention of error here I cannot find relevant info about this problem, apart from a possible problem with trans_chunk_size (not mentioned in default config), but I tried different sizes and it has no impact on the problem. trans_chunk_size=4096 trans_chunk_size=8192 trans_chunk_size=9999 Ofcourse, after every configuration change, I restarted the server: /etc/init.d/vsftpd restart What else can cause this? It's not the latest version, but it's the latest update within the repositories that has been deemed fit for enterprise usage: Package info: $ yum info vsftpd Loaded plugins: fastestmirror Installed Packages Name : vsftpd Arch : x86_64 Version : 2.0.5 Release : 24.el5_8.1 Size : 286 k Repo : installed Summary : vsftpd - Very Secure Ftp Daemon URL : http://vsftpd.beasts.org/ License : GPL Description: vsftpd is a Very Secure FTP daemon. It was written completely from scratch.

  Read the article

• Corrupt install of Ruby?

  - by wilhelmtell

  I'm having issues requiring 'digest/sha1'. ~$ ./configure --prefix=$HOME/usr --program-suffix=19 --enable-shared ~$ make ~$ make install ~$ irb19 irb(main):001:0> require 'digest/sha1' LoadError: dlopen(/Users/matan/usr/lib/ruby19/1.9.1/i386-darwin9.8.0/digest/sha1.bundle, 9): Symbol not found: _rb_Digest_SHA1_Finish Referenced from: /Users/matan/usr/lib/ruby19/1.9.1/i386-darwin9.8.0/digest/sha1.bundle Expected in: flat namespace - /Users/matan/usr/lib/ruby19/1.9.1/i386-darwin9.8.0/digest/sha1.bundle from (irb):1:in `require' from (irb):1 from /Users/matan/usr/bin/irb19:12:in `<main>' irb(main):002:0> I know some standard modules require fine, while others don't. If i'd say require 'digest' then that works fine. Just a couple of days ago I uninstalled Ruby and re-installed it. When I first installed Ruby I installed it in a similar manner, from source prefixed at my local $HOME/usr directory. I tried removing each and every file make install installs, then re-installing, but that didn't help. Do you have an idea what the issue is and how to resolve it?

  Read the article

• Windows Media Center showing Jerky Video on PC

  - by Kris Erickson

  I had to repave my Windows 7 x64 box last week due to a hard drive crash, and for a while everything was running perfectly but now all videos in Windows Media Center are jerky (the sound is fine, they just seem to skip a ton of frames all the time). This is on the local machine, but the same thing happens when I try to stream to my Xbox. The videos all show fine in VLC and Windows Media Player. I guess I must have installed something recently (in the process of getting all the apps I usually have running on my PC) that caused this but for the life of me I can't figure it out. I have updated to the latest video driver (and then rolled back to the standard Windows 7 driver), I have rolled back all the other drivers that I have installed (I believe). I have uninstalled all the codec packs (I also run TVersity, so I hate the TVersity codec pack installed), and I uninstalled TVersity. Nothing seems to help. I have uninstalled windows media center, and reinstalled it from the Programs and Features. I have basically ran out of things to try to fix this, and am almost thinking about reinstalling Windows again. Any suggestions?

  Read the article

• Disappearing Arial on 2 Macs

  - by drewk

  I noticed that Safari started rendering common web pages in a funny manner on two different Macs that I have. One is a Macbook Pro and the other a Mac Pro desktop. Yahoo and Google would appear all excessively bold or all italic and not at all look right or acceptable. The computers are all running OS X 10.6.3 "Snow Leopard" Turns out that "Arial.TTF" and "Arial Bold.ttf" got deleted somehow on these two computers. I restored Arial through Font Book and got my web mojo back. So questions: 1) Anyone seen "arial" strangely randomly disappear? The only thing in common is these are the only two computers out of eight on site that recently got Adobe CS 5 installed. Has anyone had CS 5 delete arial? 2) When I restored arial with font book, it goes into User fonts rather than the All fonts. Can I use Font Book to restore a font in /System/Library/Fonts or do I need to do that manually? 3) I located THIS article on the web regarding OS X fonts. Essentially, Snow Leopard did away with the older .dfont format and replaced with open True Type. There is a minimum font list, but Arial is not among them. Arial is installed by MS Office. 4) Why are web sites affected by Arial being missing anyway? If I look at the HTML source for Yahoo for example, "arial" is specified by name only in an ad. Yahoo itself does not specify a font name. In my Safari preferences, I have Times and Courier specified as the default font which is the default for Safari when installed. How does a missing Arial screw things up anyway? Thanks in advance.

  Read the article

• SBS 2003 boot stalls at acpitabl.dat

  - by John

  I have a SBS 2003 server running for 3 year without any problems, and few days ago it freezes during the boot. System is using two 500 Gb drives in RAID1 (Intel Matrix 7.5) After trying to load in safe mode, boot stops on acpitabl.dat. First idea was that there is a problem with RAID altough disk status was OK, and RAID status was Rebuild. I tried to boot with each drive, and one gives me the same problem, and the other drive is failing to load. Took both drives out, and checked it on a different machine. One drive is dead, other is without any problems. Returned the good drive back in SBS 2003 with changed status to Degraded, but the problem is still the same. I also have a clean SBS 2003 copy installed on this drive (previous installation), which loads smooth and quick. So, I believe the main problem is this installed version of SBS 2003. Did not make any hardware changes, did not make any updates (not sure about any automatic windows updates lately). Since there are tons posts about this problem, and no clear solution, I am trying to figure how to repair SBS 2003 installation, since there are some installed programs on this installation which I cannot re-install without additional issues.

  Read the article

• Windows 8 Doesn't Shutdown Properly With Fast Start-Up Enabled

  - by Patrick

  While Fast start-up is enabled, on turning the computer off (shutdown) the computer idles for about 5min after logging out/screen turning off. It then turns off. On returning into Windows I receive the error message saying Windows didn't shut down properly. Hibernate works fine, and I am told this shouldn't be the case - If one doesn't work, neither should. It works when both Fast start-up is enabled and disabled, as does restart and sleep. Windows is installed under UEFI. The UEFI ultra fast boot option for my motherboard cannot be enabled as my GPU doesn't support some UEFI GOP tech. As far as I know, not related to windows fast start-up, but thought it was worth mentioning. To clarify, if this: http://www.eightforums.com/tutorials/6320-fast-startup-turn-off-windows-8-a.html is enabled, the computer does not shut down properly. EDIT: Some more information on the matter: Formatting didn't fix the issue. Still fails regardless of drivers installed. Hardware was purchased ~6months ago. Running a good SSD. Event viewer Always these two messages in close succession: Error (event ID 6008): The previous system shutdown at 7:45:21 PM on ?27/?10/?2012 was unexpected. Critical (kernel power, event ID 41): The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Upon installing WPT as suggested below to figure out what was happening during shutdown, and running the cmd xbootmgr -trace shutdown -noPrepReboot -traceFlags BASE+CSWITCH+DRIVERS+POWER -resultPath C:\TEMP Windows fast start-up is now working consistently. Still works upon uninstalling WPT. This is the only change to occur on the computer. Nothing else has bee installed/uninstalled, no Windows Updates, nothing. Windows fast start-up did not work prior to installing WPT and running the cmd (made sure I tested).

  Read the article

< Previous Page | 176 177 178 179 180 181 182 183 184 185 186 187  | Next Page >