Search Results

Search found 5448 results on 218 pages for 'hibernate mapping'.

Page 183/218 | < Previous Page | 179 180 181 182 183 184 185 186 187 188 189 190  | Next Page >

  • Apache ProxyPassReverse and https

    - by joshuaball
    Hi, I would like to map all traffic on 80 and 443 from foo.com to an internal server: 192.168.1.101. I have a VirtualHost (Apache 2.2 on Ubuntu) setup as follows (note, I had to break up the hyperlinks below because I am a 'new user'): <VirtualHost *:80> ServerName foo.com ServerAlias *.foo.com ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://192.168.1.101/ ProxyPassReverse / http://192.168.1.101/ </VirtualHost> And that works great for http traffic. However, I can't seem to do the same thing for https. I have tried: Changing VirtualHost *:80 to * - but that doesn't work (I need it http-http and https-https) Creating a new VirtualHost entry for *:443 that redirects to http://192.168.1.101/, but that fails as well (browser timeouts) I did some searching, here and elsewhere, and the closest question I could find was this, but that didn't quite answer it. Also, just out of curiosity, I tried mapping all ports to https (by changing the two ProxyPass lines from http to https (and removing the :80 from VH), and that didn't work either. How would you do that as well? Any thoughts? Thanks in advance.

    Read the article

  • Looking for a comprehensive/"expert" guide to BCD parameters

    - by Stilez
    I'm interested in educating myself about BCD on Windows 8. There are many, many "walkthrough" guides" and "howtos", but I can't find any guides at typical "enthusiast" level covering what each option or argument in a BCD /ENUM dump might mean, and the principles governing how these all work together. Imagine trying to rebuild or debug BCD (including EFI/BIOS variants and recovery/hibernate/memtest sections, and perhaps multiple boot Windows/WinPE/WinRE) from scratch using just BCDedit + DiskPart, and trying to understand rather than just copy/pasting commands. That's roughly the knowledge I'm after. Example questions might be: How is a BCD /ENUM dump to be read, item by item? How do its sections work together? (A lot of guides only show a specific example rather than explaining all the all common args that can exist and what they mean, they don't actually explain how sections work together, or they assume MBR/BIOS/Vista/7 and omit info needed for EFI/GPT/Dynamic disks/8) Partitions are specified by volume letter or as a \Device\HarddiskVolumeNNN. Why does it sometimes show these items as a letter and sometimes as a GUID? What are the practical differences if any? What exactly is syntax like "ramdisk=[C:]\Images\winpe.wim,{ramdiskoptions}" saying, and how will the drive letter "C" be interpreted at runtime in a line like this? Is the drive in such a line always "C:" (most examples assume so) and if not, when wouldn't it be? Many websites state that an sdi device and path may be needed in some sections of BCD, but what is sdi and what are these args doing when they appear? How does the GUID to HDD volume/partition mapping work under EFI/GPT? So that if disks or partitions/volumes change it's clear how one can confirm from basic principles whether data shown in BCD /ENUM ALL is still correct or not. Does anyone know of a suitable reference source for this kind of raw BCD data and structures? Thanks!

    Read the article

  • LDAP not showing secondary groups

    - by Sandy Dolphinaura
    Currently, I have a LDAP server (running ClearOS if that makes any difference) containing a database of users. So, I went and setup LDAP on a couple of my debian VMs, using libpam-ldapd and I discovered this odd problem. My group/user mapping would show up when running getent group but the secondary groups would not show up when running id . Here is my /etc/nslcd.conf # /etc/nslcd.conf # nslcd configuration file. See nslcd.conf(5) # for details. # The user and group nslcd should run as. uid nslcd gid nslcd # The location at which the LDAP server(s) should be reachable. uri ldaps://10.3.0.1 # The search base that will be used for all queries. base dc=pnet,dc=sandyd,dc=me # The LDAP protocol version to use. #ldap_version 3 # The DN to bind with for normal lookups. binddn cn=manager,ou=internal,dc=pnet,dc=sandyd,dc=me bindpw Me29Dakyoz8Wn2zI # The DN used for password modifications by root. #rootpwmoddn cn=admin,dc=example,dc=com # SSL options ssl on tls_reqcert never # The search scope. #scope sub #filter group (&(objectClass=group)(gidNumber=*)) map group uniqueMember member

    Read the article

  • Outlook and IMAP - Outlook doesn't allow the Drafts and Trash folders to sync with the respective IMAP folders

    - by Matt
    I'm using Outlook 2007 and Outlook 2010 against an IMAP server (the problem exists across many, like Gmail, you name it). Outlook lets you set your Outlook "Sent" folder to map to the IMAP server's Sent folder (the other choice is to map your Outlook Sent to your Personal Folders Sent) - this is good. When you send a message from Outlook and then look in the sent folder of the IMAP server (e.g. from a different client or from a browser), the messages are there. This is the behavior I want. Outlook does NOT support the same behavior for Drafts and Trash. In both cases, items deleted (or Drafts saved) in Outlook go in to Outlook's local folders and do NOT show on the IMAP server's Trash or Drafts folders. Same problem in reverse. Thunderbird on the other hand does support the proper mapping of Drafts, Sent and Trash. I expected this to be IMAP-specific but it appears to be client specific. What does Outlook implement it this way and is there a workaround?

    Read the article

  • postgresql No space left on device

    - by pstanton
    Postgres is reporting that it is out of disk space while performing a rather large aggregation query: Caused by: org.postgresql.util.PSQLException: ERROR: could not write block 31840050 of temporary file: No space left on device at org.postgresql.core.v3.QueryExecutorImpl.receiveErrorResponse(QueryExecutorImpl.java:1592) at org.postgresql.core.v3.QueryExecutorImpl.processResults(QueryExecutorImpl.java:1327) at org.postgresql.core.v3.QueryExecutorImpl.execute(QueryExecutorImpl.java:192) at org.postgresql.jdbc2.AbstractJdbc2Statement.execute(AbstractJdbc2Statement.java:451) at org.postgresql.jdbc2.AbstractJdbc2Statement.executeWithFlags(AbstractJdbc2Statement.java:350) at org.postgresql.jdbc2.AbstractJdbc2Statement.executeUpdate(AbstractJdbc2Statement.java:304) at org.hibernate.engine.query.NativeSQLQueryPlan.performExecuteUpdate(NativeSQLQueryPlan.java:189) ... 8 more However the disk has quite a lot of space: Filesystem Size Used Avail Use% Mounted on /dev/sda1 386G 123G 243G 34% / udev 5.9G 172K 5.9G 1% /dev none 5.9G 0 5.9G 0% /dev/shm none 5.9G 628K 5.9G 1% /var/run none 5.9G 0 5.9G 0% /var/lock none 5.9G 0 5.9G 0% /lib/init/rw The query is doing the following: INSERT INTO summary_table SELECT t.a, t.b, SUM(t.c) AS c, COUNT(t.*) AS count, t.d, t.e, DATE_TRUNC('month', t.start) AS month, tt.type AS type, FALSE, tt.duration FROM detail_table_1 t, detail_table_2 tt WHERE t.trid=tt.id AND tt.type='a' AND DATE_PART('hour', t.start AT TIME ZONE 'Australia/Sydney' AT TIME ZONE 'America/New_York')>=23 OR DATE_PART('hour', t.start AT TIME ZONE 'Australia/Sydney' AT TIME ZONE 'America/New_York')<13 GROUP BY month, type, t.a, t.b, t.d, t.e, FALSE, tt.duration any tips?

    Read the article

  • Tooltips shadow stuck on desktop

    - by faulty
    I tends to get this problem from time to time. The tooltips with a shadow appearing on top of everything. It's the shadow of the tooltips not disappearing after the tooltips disappear. The last one I had the tooltips was from the wifi connection list at the systray. This problem also happen to me on another computer. Both running Win7 with ATI gpu. I found this similar post Menu command stuck on screen but none of the solution helped. In fact the "Fade or slide tooltips into view" has been unchecked from the beginning. Ending task of "dwm.exe" also doesn't help. So far the only way to resolve this by restarting window. I can't post picture yet, so can't show any screenshot. Edit: Just tested a few more trick which doesn't work. 1. Turn of aero 2. Hibernate 3. Switch main display to external display and switch back. 4. Change resolution

    Read the article

  • ssh keys rejected each day

    - by EddyR
    I've had OpenSSH server running on my debian server for a couple weeks and all of a sudden now when I go to login the next day it rejects my ssh key and I have to manually add a new one each time. Not only that but I have the "tunneling with clear-text passwords" option enabled and the non-root (login with root is disabled) account for that is rejected too. I'm at a loss why this is happening and I can't find any ssh options that would explain it. --update-- I just changed debug level to DEBUG. But before that I'm seeing a lot of the following in auth.log Feb 1 04:23:01 greenpages CRON[7213]: pam_unix(cron:session): session opened for user root by (uid=0) Feb 1 04:23:01 greenpages CRON[7213]: pam_unix(cron:session): session closed for user root ... Feb 1 04:36:26 greenpages sshd[7217]: reverse mapping checking getaddrinfo for nat-pool-xx-xx-xx-xx.myinternet.net [xx.xx.xx.xx] failed - POSSIBLE BREAK-IN ATTEMPT! ... Feb 1 04:37:31 greenpages sshd[7223]: Did not receive identification string from xx.xx.xx.xx ... My sshd_conf file settings are: # Package generated configuration file # See the sshd(8) manpage for details # What ports, IPs and protocols we listen for Port xxx # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH LogLevel DEBUG # Authentication: LoginGraceTime 120 PermitRootLogin no StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords PasswordAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding no X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no #MaxStartups 10:30:60 #Banner /etc/issue.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server UsePAM no ClientAliveInterval 60 AllowUsers myuser

    Read the article

  • Windows Server Hyper-V guests cannot see each other on network

    - by Noldorin
    I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

    Read the article

  • Windows Server Hyper-V guests cannot see each other on network

    - by Noldorin
    I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

    Read the article

  • Scheduled task does not run on WIndows 2003 server on VMWare unattened, runs fine otherwise

    - by lnm
    Scheduled task does not run on Windows 2003 server on VMWare. The same setup runs fine on standalone server. Test below explains the problem. We really need to run a more complex bat file, but this shows the issue. I have a bat file that copies a file from server A to server B. I use full path name, no drive mapping. Runs fine on server B from command prompt. I created a task that runs this bat file under a domain id with password that is part of administrator group on both servers. Task runs fine from Scheduled task screen, and as a scheduled task as long as somebody is logged into the server. If nobody is logged in, the task does not run. There is no error message in Task Scheduler log, just an entry that the task started, bit no entry for finish or an error code. To add insult to injury, if the task copies a file in the opposite direction, from server B to server A, it runs fine as a scheduled unattended task. If I copy a file from server B to server B, the task also runs fine unattended, I recreated exactly the same setup on a standalone server. No issues at all. I checked obvious things like the task has "run only as logged in" unchecked, domain id has run as a batch job privilege and logon rights, Task Scheduler service runs as a local system, automatic start. Any suggestions?

    Read the article

  • Installing OEM Windows Server 2008 under KVM

    - by rancidfishbreath
    Issue I have an HP server that came with an OEM copy of Windows Server 2008. I have installed CentOS 5.4 on the hardware and am trying to install Windows Server 2008 as a KVM guest. When I attempt to install Windows Server 2008 it complains that I am trying to install on unsupported hardware. This issue is caused because the hardware SMBIOS information is not being passed to the KVM guest. Background Before I go any further I want to state that what I am trying to do is within the license. HP offers a supported solution for VMWare but does not have an official solution for KVM. After much research the platform I am going to use is CentOS and KVM so please do not suggest other platforms. I emailed the KVM developers mailing list and was told that this is possible and was given the advice that: "You can dump SLIC table of your host bios and provide it to guest bios using -acpitable parameter." I used dmidecode and got the parameters that need to be passed, but I do not know where to pass the parameters into. Update Looks like CentOS 5.4 uses virt-install instead of qemu. Qemu is in the package manager and I was able to install it after uninstalling qemu-img (they conflict and qemu contains the packages in qemu-img). So now I know how to pass the acpitable parameters, but I am having trouble mapping what came out of dmidecode into -acpitable.

    Read the article

  • Email test deferred (mail transport unavailable) with ClamAV

    - by dirt
    I'm trying to set up a simple new mail server; when I send a test email to the server the email is getting hung up during delivery (user mapping is found) and the email is never found in /home/user/Maildir/new Here is my maillog after a fresh reboot and test email, there are a few warnings I am unfamiliar with. Can you please point me in the right direction? Oct 25 14:54:57 loki dovecot: master: Dovecot v2.0.9 starting up (core dumps disabled) Oct 25 14:54:58 loki postfix/postfix-script[1369]: starting the Postfix mail system Oct 25 14:54:58 loki postfix/master[1370]: daemon started -- version 2.6.6, configuration /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: request to update table btree:/etc/postfix/smtpd_scache in non-postfix directory /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: redirecting the request to postfix-owned data_directory /var/lib/postfix Oct 25 14:56:00 loki postfix/smtpd[1455]: connect from mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/smtpd[1455]: 1CF5E20A8B: client=mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/cleanup[1461]: 1CF5E20A8B: message-id= Oct 25 14:56:01 loki postfix/qmgr[1379]: 1CF5E20A8B: from=, size=1788, nrcpt=1 (queue active) Oct 25 14:56:01 loki postfix/qmgr[1379]: warning: connect to transport private/scan: No such file or directory Oct 25 14:56:01 loki postfix/error[1462]: 1CF5E20A8B: to=, orig_to=, relay=none, delay=0.18, delays=0.15/0.02/0/0.01, dsn=4.3.0, status=deferred (mail transport unavailable) Oct 25 14:56:01 loki postfix/smtpd[1455]: disconnect from mail-ob0-f180.google.com[209.85.214.180] master.cf snippets: # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - n - - smtpd submission inet n - n - - smtpd -o smtpd_tls_security_level=encrypt # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING smtps inet n - n - - smtpd -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING scan unix - - n - 16 smtp -o smtp_data_done_timeout=1200 -o smtp_send_xforward_command=yes -o disable_dns_lookups=yes 127.0.0.1:10026 inet n - n - 16 smtpd -o content_filter= -o local_recipient_maps= -o relay_recipient_maps= -o smtpd_restriction_classes= -o smtpd_client_restrictions= -o smtpd_helo_restrictions= -o smtpd_sender_restrictions= -o smtpd_recipient_restrictions=permit_mynetworks,reject -o mynetworks_style=host -o smtpd_authorized_xforward_hosts=127.0.0.0/8

    Read the article

  • Configuring vlans on Cisco SG200 series switch with Ubuntu server

    - by nixnotwin
    I created a vlan on Ubuntu with vconfig tool with 21 as id and eth1 as the host port. I connected eth1 to one of the ports on the swtich (GE23) as all ports trunk by default. In the webgui I created a vlan named test with the id 21 and I made GE2 are port as an access port. In port to vlan mapping I selected vlan 21 and added it port GE2 by selecting untagged option. I have assigned 192.168.1.1/24 as the ip of eth1.21 on Ubuntu. If I connect another cleint pc to GE2 port with a ip of 192.168.1.2/24 I cannot ping the server ip (192.168.1.1/24). Ping from server to client also does not work. I inspected packets that are sent out eth1 on the server and I could see the vlan 21 tag. And I connect the other end of the cable to a different Linux pc and inspected the packets but no vlan tags can be seen. What could be preventing me from getting vlans working? Edit 1 screenshots:

    Read the article

  • How to connect to a computer that is in Sleep mode over the internet

    - by Gerhard Weiss
    How to connect to a computer that is in Sleep mode over the internet? I am using LogMeIn to connect to another computer offsite. I just installed Windows 7 RC on that system and found that the Sleep mode actually works. Currently LogMeIn does not connect when the system is in Sleep mode or Hibernate mode (that is what their error message displays when you try). Is there a way to get LogMeIn to connect to a system in Sleep mode? Is there other software that gives simliar LogMeIn functionallity (like RDP, etc.) that could be used on Windows 7 instead. I just use LMI for connecting and nothing else (no printing or file transfers). A Non-expensive options (such as free) would be better. I have seen web sites mentioning "Wake on LAN". Does anyone have some good links on how to set this up to be accessed over the internet? Edited: It looks like LogMeIn BETA might be the solution. https://beta.logmein.com/welcome/nextgen/ Has anyone tried this beta yet?

    Read the article

  • Networking DOS within Windows 7 XP Mode, with a Windows XP/7 Networked Share

    - by theonlylos
    For awhile now, one of my clients has been stuck with Corel Paradox 4.0 (it used to be the biggest database system in the DOS days, until Microsoft released Access in the early 90's) so for awhile I've managed to keep it on life support on Windows XP for a few years, however since switching to Windows 7 x64, I've had to resort to using XP Mode as the sandbox to keep it up and running. While I am able to run Paradox as usual in XP Mode, I'm having a serious issue where if I try connecting the install to the network share (which is located on the Windows 7 portion of the system), Paradox keeps exiting because it says the serial number is invalid. Now, I know for a fact that this is an issue with the virtual loopback adapter and also having the VM linked to the physical ethernet adapter -- and while I have solved this issue before, most of my fixes have been bandages since after a few weeks the issue pops up again. Long story short, I wanted to ask if there is a permanent way to link a DOS program to a network share address. For example, when I try doing \tsclient\paradox (the Windows 7 Address) I keep getting an error saying I need a valid network address. I've tried mapping that folder to various drive letters such as P:\Paradox -- but for some reason that keeps failing over time. For what it's worth, Paradox uses a .SOM file to store the network settings, however it isn't editable in Notepad but rather it's controlled by a wizard in Paradox. But if that extension rings any bells, I'd welcome any insights.

    Read the article

  • Shared printer stops working on clients but not host computer

    - by Tony
    I have a Brother MFC-7420 USB all-in-one laser printer. It is plugin via USB to my Windows 7 x64 machine. I have it shared to a few users on my home network. My wife's laptop running Vista x64 can normally print fine to the printer. However it seems that every day or two, when she pushes print on a something it just sits in her laptop's print queue and never makes it to my desktop. The only thing that seems to fix this is if she restarts her laptop. Not a big deal but this problem is sort of annoying. I don't know if this affects but the laptop is put into hibernate at night and I turn my desktop off at night. Does anyone know why this happens and if there is something easy to do to fix the problem besides restart the computer? EDIT: I was thinking that maybe my wife's laptop loses its connection to the printer. Is there a way to reset a connection to a shared printer? Or maybe reauth with the printer?

    Read the article

  • Network share not always available on Windows 2003

    - by JP Hellemons
    Hello everybody, we have a windows 2003 server with a shared directory/folder. I've seen this thread but this wasn't any help: http://superuser.com/questions/58890/the-specified-network-name-is-no-longer-available I have a ping -t running from 3 pc's (vista and two windows 7) they all work. the problem occurss when two users enter the network share then this 'network share is no longer available' appears and the explorer windows turn white. after f5 or refresh the shared directory is back. this is really strange. there is no anti virus or kasparsky running on either end. this is all in the same LAN. the internet connection is really stable, so it's really strange. because a stable internet connection should imply that the local network connection is also stable and that this is a windows issue. can it be a router issue? I have checked the eventlog on the server for diskfailure related messages, but there are none. EDIT: can this be related to mapping a shared directory to a drive letter? and that there is a router between me and the mapped network drive? or is it just windows that is not working well with two users on the same shared folder? should I install samba or something?

    Read the article

  • QNAP NAS 509 (LINUX) - how to unmout busy volume and find physical disk?

    - by Horst Walter
    On my NAS QNAP TS 509 I do have a technical issue. I need to run e2fsck. This works fine for me on md0 (see below), but how can I unmount the busy devices md9 and sda4 in order to do the same. Whenever I try, I fail because the device is busy. [This part is solved, see below] In order to further track down the issue, I'd need to sort out the physical disk to device relationship. How can I find out this, e.g. md0 is a stripped volume on 2 disk (but I need to find out on what physical disk). Remark: As you can easily derive from my questions, I am not a Linux expert, but manage to get along. /dev/ram0 124.0M 94.1M 29.8M 76% / tmpfs 32.0M 80.0k 31.9M 0% /tmp /dev/sda4 310.0M 103.9M 206.1M 34% /mnt/ext /dev/md9 509.5M 39.2M 470.2M 8% /mnt/HDA_ROOT /dev/md0 1.8T 1.4T 444.7G 76% /share/MD0_DATA tmpfs 32.0M 0 32.0M 0% /.eaccelerator.tmp -- Added -- QNAP seems to be based on Busybox. I do not find something like init / telinit / runlevel. At busybox docs it says that I need to run the below. But in /var/service sv is not available. I want to go to single user mode to unmount the devices. # cd /var/service # sv d * # sv u getty* -- Added, thanks A4L -- This QNAP Box runs a special flavor of Linux, so not all SOPs do apply. In my particular case I found a services.sh script, stopping all services. After that the drive could be unmounted. The information passed by A4L is valid and worth reading it, maybe I'll profit from it next time. Links: http://unix.stackexchange.com/questions/19918/umount-device-is-busy and http://unix.stackexchange.com/questions/15024/umount-device-is-busy-why So the unmount issue is solved, still looking for the best option to find the physical to volume mapping.

    Read the article

  • can't properly shutdown ubuntu and sound problem on HP mini 311 netbook

    - by Viele
    hi, I recently bought a HP mini 311 netbook. I replaced its harddrive and installed ubuntu 10.04. Since then, I have encountered some very strange problem with its sound and shutdown/reboot. At times, when I start the computer, it will have no sound, on the GUI the sound is at max, but no sound is available. This sometimes also happen after after upgrades, hibernate, and toggling the wireless radio button. Strangely, when the sound is out the device will also refuse to be shutdown. If I shutdown the computer using the GUI, it will simply go back to the log in screen without actually shutting down. If I use "sudo shutdown 0", the computer will hang on the loading screen of the shut down process. I had to force the pc to shutdown by holding the power button down. usually (probably always) after I force a turn-off then start off again. the sound and shutdown become normal. I wonder if anyone have clues regarding to the cause of this problem. This the info about the computer: 1) installed ubuntu 10.04LTS RC, later upgraded to formal released version. 2) cat /proc/asound/version == "Advanced Linux Sound Architecture Driver Version 1.0.21." however, when doing 'alsaconf' the version displayed is 1.0.23 any help is appreciated. Thanks

    Read the article

  • How to extract a Vorbis stream from a WAVE file?

    - by H.B.
    I would like to move the Vorbis stream into an ogg container but ffmpeg does not seem to recognize the stream. Even though MPlayer gives this output upon playback: Opening audio decoder: [acm] Win32/ACM decoders Loading codec DLL: 'vorbis.acm' Loaded DLL driver vorbis.acm at 10000000 Warning! ACM codec reports srcsize=0 AUDIO: 44100 Hz, 2 ch, s16le, 128.0 kbit/9.07% (ratio: 16000-176400) Selected audio codec: [vorbisacm] afm: acm (OggVorbis ACM) ffmpeg: ffmpeg -i Source.wav -acodec copy Target.ogg Input #0, wav, from 'Source.wav': Duration: 00:02:15.17, bitrate: 128 kb/s Stream #0.0: Audio: qg[0][0] / 0x6771, 44100 Hz, 2 channels, 128 kb/s [ogg @ 00000000003096C0] Unsupported codec id in stream 0 Output #0, ogg, to 'Target.ogg': Metadata: encoder : Lavf53.6.0 Stream #0.0: Audio: qg[0][0] / 0x6771, 44100 Hz, 2 channels, 128 kb/s Stream mapping: Stream #0.0 -> #0.0 Could not write header for output file #0 (incorrect codec parameters ?) Of course this does not necessarily need to be done via ffmpeg, any method that is workable would be fine... I have cut down one of the files to 512KB: sample.wav (Changed two chunk size fields in the wave header to account for this, the embedded stream is cut "without notice")

    Read the article

  • No LPT port in Windows 7 virtual machines

    - by KeyboardMonkey
    Windows 7 has MS virtual PC integrated, the VM settings don't give a parallel LPT port mapping to the physical machine. Where did it go? Has anyone else noticed this, and found a solution? Update: After much digging, I found the one and only reference to this issue, on the VPC Blog: "Parallel port devices are not supported, as they are relatively rare today." -More details- It's a XP VM I've been using since VPC 2007 days, which did have this functionality. This is to configure barcode printers via the LPT port. Since the (new) MS VM can't map to my physical LPT port, I'm having a hard time configuring printers. My physical ports are enabled in the BIOS. It has worked the past 3 years, before switching to Win 7. Any help is appreciated. This screen shot of the VM settings shows COM ports, but LPT is no more In contrast, here is a screen shot of VPC 2007 (before it got integrated into Win 7). Notice how it has LPT support

    Read the article

  • postfix (for sending mail only) multiple domain setup

    - by seanl
    I have the following problem, I have a Centos 5.4 VPS hosting a few nginx sites (some static, some cakephp), I would like to be able to send email from each sites contact page through postfix to my google apps hosted email (different accounts for each site) so that apps can then send out an auto email to the person filling in the contact form etc I have a bare-bones postfix installation with the following added into the main.cf config file. from using this guide virtual_alias_domains = hash:/etc/postfix/virtual_alias_domains virtual_alias_maps = hash:/etc/postfix/virtual_alias_maps (both of these files have been converted into db files using postmap) I have configured DNS correctly for each site and setup SPF records. (I'm aware R-DNS will still reference my actual hostname not the domain name and cause a possible spam issue but one thing at a time) I can telnet localhost and the helo localhost so that I can send a command line email from an address in the virtual_alias_domains to an email in the virtual_alias_maps file which seems sends without giving an error but it is sending to my local linux account not the email address specified. my question is am i approching this the wrong way in terms of the virtual alias mapping or is this even possible to do in the manner im trying. Any help is greatly appreciated thanks. my postconf -n outlook looks like this alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix debug_peer_level = 2 html_directory = no inet_interfaces = localhost mail_owner = postfix mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost myhostname = myactual hostname mynetworks = 127.0.0.0/8 myorigin = $mydomain newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.3.3/README_FILES sample_directory = /usr/share/doc/postfix-2.3.3/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop unknown_local_recipient_reject_code = 550 virtual_alias_domains = hash:/etc/postfix/virtual_alias_domains virtual_alias_maps = hash:/etc/postfix/virtual_alias_maps

    Read the article

  • IIS doesn't serve certain file extensions

    - by Alekc
    Hi, i have this weird issue on Win 2k3 server and IIS: Iis has several sites, in one of them i need to create a subdir and set up it as web application. I've noticed that if i create new directory and put some .js/.txt file into it, they will not be served by iis (IE gives an error Internet Explorer cannot display the webpage). If i put the same files in another old site's subdirectory it will show correctly. By sniffing traffic i've seen that iis reply connection state 200 and then drop completely any connection http://domain.com/test2/prova.txt GET /test2/prova.txt HTTP/1.1 Host: domain.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.1.7) Gecko/20091221 Firefox/3.5.7 (.NET CLR 3.5.30729) Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive HTTP/1.x 200 OK If i rename file prova.txt in prova.asp for example it showing without problems so it shouldn't be permissions issue. After making some researches I've found out that it can be caused by missing mime types, I've checked out .txt and .js are present and served by aspnet_isapi.dll. And here comes another weird thing: if i remove mime mapping from directory's properties it's served correctly, but the same thing doesn't work with js. I'm really beginning to be out of ideas, is there someone who have some hint? Thanks in advance.

    Read the article

  • FFMPEG: how to add watermark to video?

    - by DocWiki
    My Platform: Ubuntu 10.10 + FFMPEG 0.5.3(I installed ffmpeg from source) I try to add Watermark to a .MOV video with FFMPEG 0.5.3 imlib2.so (Please note FFMPEG 0.6+ dont support imlib2.so, so I use ffmpeg 0.5.3) Here is my code: ffmpeg -sameq -i example.mov -vhook '/usr/local/lib/vhook/imlib2.so -x 0 -y 0 -i /var/www/files/watermark.png' newexample.mov Here is the output: FFmpeg version 0.5.3, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --enable-avfilter --enable-filter=movie --enable-avfilter-lavf libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 built on Jul 3 2011 12:05:08, gcc: 4.4.5 Seems stream 1 codec frame rate differs from container frame rate: 59.94 (5994/100) - 29.97 (30000/1001) Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'example.mov': Duration: 00:03:14.06, start: 0.000000, bitrate: 3350 kb/s Stream #0.0(eng): Audio: aac, 48000 Hz, stereo, s16 Stream #0.1(eng): Video: h264, yuv420p, 1150x647, 29.97 tbr, 29.97 tbn, 59.94 tbc Output #0, mov, to 'newexample.mov': Stream #0.0(eng): Video: mpeg4, yuv420p, 1150x647, q=2-31, 200 kb/s, 90k tbn, 29.97 tbc Stream #0.1(eng): Audio: 0x0000, 48000 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.1 - #0.0 Stream #0.0 - #0.1 Unsupported codec for output stream #0.1 What could be the possible problem? Is that AAC or H264 that is not supported? I installed libavcodec-extra-52, linfaac, libfaad and etc. but the error is the same. Do I have to install following this instruction? HOWTO: Install and use the latest FFmpeg and x264 or there is a simpler solution?

    Read the article

  • Xen domU passwd file overwritten with console log output

    - by malfy
    I was setting up a Debian Xen domU and after booting it fine, I added basic configuration to /etc/network/interfaces and ran /etc/init.d/networking restart. This failed so I decided to reboot. After the reboot I also ran xm shutdown box. When dropped to a shell prompt it wouldn't let me login. Upon further inspection, I now have garbage in some critical files in /etc: root@box:/# tail +1 mnt/etc/{passwd-,shadow} tail: cannot open `+1' for reading: No such file or directory ==> mnt/etc/passwd- <== 0000000000100000 (reserved) Nov 23 02:02:39 box kernel: [ 0.000000] Xen: 0000000000100000 - 0000000004000000 (usable) Nov 23 02:02:39 box kernel: [ 0.000000] DMI not present or invalid. Nov 23 02:02:39 box kernel: [ 0.000000] last_pfn = 0x4000 max_arch_pfn = 0x1000000 Nov 23 02:02:39 box kernel: [ 0.000000] initial memory mapped : 0 - 033ff000 Nov 23 02:02:39 box kernel: [ 0.000000] init_memory_mapping: 0000000000000000-0000000004000000 Nov 23 02:02:39 box kernel: [ 0.000000] NX (Execute Disable) protection: active Nov 23 02:02:39 box kernel: [ 0.000000] 0000000000 - 0004000000 page 4k Nov 23 02:02:39 box kernel: [ 0.000000] kernel direct mapping tables up to 4000000 @ 7000-2c000 Nov 23 02:02:3 ==> mnt/etc/shadow <== 32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1 Nov 23 02:02:39 box kernel: [ 0.000000] PERCPU: Embedded 15 pages/cpu @c15b0000 s37688 r0 d23752 u65536 Nov 23 02:02:39 box kernel: [ 0.000000] pcpu-alloc: s37688 r0 d23752 u65536 alloc=16*4096 Nov 23 02:02:39 box kernel: [ 0.000000] pcpu-alloc: [0] 0 Nov 23 02:02:39 box kernel: [ 0.000000] Xen: using vcpu_info placement Nov 23 02:02:39 box kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16160 Nov 23 02:02:39 box kernel: [ 0.000000] Kernel command line: root=/dev/mapper/xen-guest_root ro quiet root=/dev/xvda1 ro Nov 23 02:02:39 box kernel: [ 0.000000] PID hash table entries: The garbage is also present in the passwd file and the group file (although I didn't paste that above since I have since ran debootstrap on the filesystem again). Does anyone have any insight into what happened and why?

    Read the article

< Previous Page | 179 180 181 182 183 184 185 186 187 188 189 190  | Next Page >