Search Results

Search found 5439 results on 218 pages for 'madhup 25'.

Page 186/218 | < Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >

• vlans on openvz, centos 6

  - by arheops

  i have centos 6 with openvz installed on it, switch with vlan support. I need following setup: 1) eth0 on openvz have be tagged multiple vlans. 2) each virtualhost have to be in single vlan. yes,i already read wiki on openvz, but it is just not work. I have on main server interface eth0.108 and able ping address on that interface(using nootbook on untagged port vlan 108), but i not able ping address inside container. Main node: [root@box1 conf]# ifconfig eth0 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:506 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68939 (67.3 KiB) TX bytes:1780 (1.7 KiB) Interrupt:16 Memory:c0000000-c0012800 eth0.108 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet addr:10.11.108.3 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:238 errors:0 dropped:0 overruns:0 frame:0 TX packets:19 errors:0 dropped:12 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:25890 (25.2 KiB) TX bytes:926 (926.0 b) eth1 Link encap:Ethernet HWaddr D0:67:E5:F4:11:61 inet addr:192.168.23.233 Bcast:192.168.23.255 Mask:255.255.255.0 inet6 addr: fe80::d267:e5ff:fef4:1161/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1967 errors:0 dropped:0 overruns:0 frame:0 TX packets:356 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:365298 (356.7 KiB) TX bytes:115007 (112.3 KiB) Interrupt:17 Memory:c2000000-c2012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:784 (784.0 b) TX bytes:784 (784.0 b) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet6 addr: fe80::1/128 Scope:Link UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:3 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth108.0 Link encap:Ethernet HWaddr 00:18:51:DA:94:D5 inet6 addr: fe80::218:51ff:feda:94d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:639 errors:0 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:17996 (17.5 KiB) TX bytes:308 (308.0 b) virtual node [root@pbx108 /]# ifconfig eth0.108 Link encap:Ethernet HWaddr 00:18:51:CA:B5:C5 inet addr:10.11.108.1 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::218:51ff:feca:b5c5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:685 errors:0 dropped:2 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:308 (308.0 b) TX bytes:19284 (18.8 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:683 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76288 (74.5 KiB) TX bytes:76288 (74.5 KiB) /etc/vz/conf/108.conf # RAM PHYSPAGES="0:4000M" # Swap SWAPPAGES="0:512M" # Disk quota parameters (in form of softlimit:hardlimit) DISKSPACE="200G:200G" DISKINODES="20000000:22000000" QUOTATIME="0" # CPU fair scheduler parameter CPUUNITS="4000" VE_ROOT="/vz/root/$VEID" VE_PRIVATE="/vz/private/$VEID" OSTEMPLATE="centos-6-x86_64" ORIGIN_SAMPLE="vswap-256m" NETIF="ifname=eth0.108,mac=00:18:51:CA:B5:C5,host_ifname=veth108.0,host_mac=00:18:51:DA:94:D5" NAMESERVER="8.8.8.8" HOSTNAME="pbx108.localhost" IP_ADDRESS=""

  Read the article

• Cisco Pix how to add an additional block of static ip addresses for nat?

  - by Scott Szretter

  I have a pix 501 with 5 static ip addresses. My isp just gave me 5 more. I am trying to figure out how to add the new block and then how to nat/open at least one of them to an inside machine. So far, I named a new interface "intf2", ip range is 71.11.11.58 - 62 (gateway should 71.11.11.57) imgsvr is the machine I want to nat to one of the (71.11.11.59) new ip addresses. mail (.123) is an example of a machine that is mapped to the current existing 5 ip block (96.11.11.121 gate / 96.11.11.122-127) and working fine. Building configuration... : Saved : PIX Version 6.3(4) interface ethernet0 auto interface ethernet0 vlan1 logical interface ethernet1 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 nameif vlan1 intf2 security1 enable password xxxxxxxxx encrypted passwd xxxxxxxxx encrypted hostname xxxxxxxPIX domain-name xxxxxxxxxxx no fixup protocol dns fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 no fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 names ...snip... name 192.168.10.13 mail name 192.168.10.29 imgsvr object-group network vpn1 network-object mail 255.255.255.255 access-list outside_access_in permit tcp any host 96.11.11.124 eq www access-list outside_access_in permit tcp any host 96.11.11.124 eq https access-list outside_access_in permit tcp any host 96.11.11.124 eq 3389 access-list outside_access_in permit tcp any host 96.11.11.123 eq https access-list outside_access_in permit tcp any host 96.11.11.123 eq www access-list outside_access_in permit tcp any host 96.11.11.125 eq smtp access-list outside_access_in permit tcp any host 96.11.11.125 eq https access-list outside_access_in permit tcp any host 96.11.11.125 eq 10443 access-list outside_access_in permit tcp any host 96.11.11.126 eq smtp access-list outside_access_in permit tcp any host 96.11.11.126 eq https access-list outside_access_in permit tcp any host 96.11.11.126 eq 10443 access-list outside_access_in deny ip any any access-list inside_nat0_outbound permit ip 192.168.0.0 255.255.0.0 IPPool2 255.255.255.0 access-list inside_nat0_outbound permit ip 172.17.0.0 255.255.0.0 IPPool2 255.255.255.0 access-list inside_nat0_outbound permit ip 172.16.0.0 255.255.0.0 IPPool2 255.255.255.0 ...snip... access-list inside_access_in deny tcp any any eq smtp access-list inside_access_in permit ip any any pager lines 24 logging on logging buffered notifications mtu outside 1500 mtu inside 1500 ip address outside 96.11.11.122 255.255.255.248 ip address inside 192.168.10.15 255.255.255.0 ip address intf2 71.11.11.58 255.255.255.248 ip audit info action alarm ip audit attack action alarm pdm location exchange 255.255.255.255 inside pdm location mail 255.255.255.255 inside pdm location IPPool2 255.255.255.0 outside pdm location 96.11.11.122 255.255.255.255 inside pdm location 192.168.10.1 255.255.255.255 inside pdm location 192.168.10.6 255.255.255.255 inside pdm location mail-gate1 255.255.255.255 inside pdm location mail-gate2 255.255.255.255 inside pdm location imgsvr 255.255.255.255 inside pdm location 71.11.11.59 255.255.255.255 intf2 pdm logging informational 100 pdm history enable arp timeout 14400 global (outside) 1 interface global (outside) 2 96.11.11.123 global (intf2) 3 interface global (intf2) 4 71.11.11.59 nat (inside) 0 access-list inside_nat0_outbound nat (inside) 2 mail 255.255.255.255 0 0 nat (inside) 1 0.0.0.0 0.0.0.0 0 0 static (inside,outside) tcp 96.11.11.123 smtp mail smtp netmask 255.255.255.255 0 0 static (inside,outside) tcp 96.11.11.123 https mail https netmask 255.255.255.255 0 0 static (inside,outside) tcp 96.11.11.123 www mail www netmask 255.255.255.255 0 0 static (inside,outside) 96.11.11.124 ts netmask 255.255.255.255 0 0 static (inside,outside) 96.11.11.126 mail-gate2 netmask 255.255.255.255 0 0 static (inside,outside) 96.11.11.125 mail-gate1 netmask 255.255.255.255 0 0 access-group outside_access_in in interface outside access-group inside_access_in in interface inside route outside 0.0.0.0 0.0.0.0 96.11.11.121 1 route intf2 0.0.0.0 0.0.0.0 71.11.11.57 2 timeout xlate 0:05:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00 timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute floodguard enable ...snip... : end [OK] Thanks!

  Read the article

• Possible to give one connection to each IP?

  - by Alice

  I am having overloading problems. Too many connections, and some IP has more than 20 connection at once. I do this command. netstat -anp |grep 'tcp\|udp' | awk '{print $5}' | cut -d: -f1 | sort | uniq -c | sort -n To get total of connection and this is the output: 1 106.3.98.81 1 106.3.98.82 1 108.171.251.2 1 110.85.103.207 1 111.161.30.217 1 113.53.103.55 1 119.235.237.20 1 124.106.19.34 1 157.55.32.166 1 157.55.33.49 1 157.55.34.28 1 175.141.103.239 1 180.76.5.59 1 180.76.5.61 1 188.235.165.216 1 205.213.195.70 1 216.157.222.25 1 218.93.205.100 1 222.77.209.105 1 27.153.148.109 1 27.159.194.242 1 27.159.253.71 1 54.242.122.201 1 61.172.50.99 1 65.55.24.239 1 71.179.78.5 1 74.125.136.27 1 74.125.182.30 1 74.125.182.36 1 79.112.225.39 1 93.190.139.208 2 124.227.191.67 2 157.55.33.84 2 157.55.35.34 2 190.66.3.107 2 203.87.153.38 2 220.161.119.3 2 221.6.15.156 2 27.153.148.116 2 27.159.197.0 2 96.47.224.42 3 202.14.70.1 3 218.6.15.42 3 222.77.218.226 3 222.77.224.187 3 37.59.66.100 3 46.4.181.244 3 87.98.254.192 3 91.207.8.62 4 188.143.233.222 4 218.108.168.166 4 221.12.154.18 4 93.182.157.8 4 94.142.128.183 5 180.246.170.187 5 8.21.6.226 6 178.137.94.87 6 218.93.205.112 7 199.15.234.222 9 9 125.253.97.6 10 178.137.17.196 11 46.118.192.179 12 212.79.14.14 21 72.201.187.135 27 0.0.0.0 Can anyone give me some directions, my server crashed few times this week because of this. Thanks. EDIT: Alright, my error logs says: [Thu Oct 18 12:17:39 2012] [error] could not make child process 4842 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4843 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4855 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4856 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4861 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4869 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4872 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4873 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4874 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4875 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4876 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4880 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4882 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4885 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4897 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4900 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4901 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4906 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4907 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4925 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4926 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4927 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4931 exit, attempting to continue anyway [Thu Oct 18 12:17:40 2012] [notice] caught SIGTERM, shutting down PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20060613+lfs/curl.iso' - /usr/lib/php5/20060613+lfs/curl.iso: cannot open shared object file: No such file or directory in Unknown on line 0 [Thu Oct 18 12:17:45 2012] [notice] Apache/2.2.9 (Debian) PHP/5.2.6-1+lenny10 with Suhosin-Patch configured -- resuming normal operations And I have over thousands of line saying:(each has different process id) [Thu Oct 18 12:17:38 2012] [error] child process 4906 still did not exit, sending a SIGKILL And I also have line saying: [Wed Oct 17 09:44:58 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 50 MaxClients 300 MaxRequestsPerChild 5000 </IfModule>

  Read the article

• Postfix logs missing information on delivery status (postfix/smtp message)

  - by hegemon

  I noticed a problem with postfix logs, that information on some of emails delivery status is missing. The issue affects about 1% of emails. "Healthy" log: <server># grep 8EB992EFBB44 postfix_log/mail04.log Jun 5 03:09:29 mail04 postfix/smtpd[8537]: 8EB992EFBB44: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 5 03:09:29 mail04 postfix/cleanup[34349]: 8EB992EFBB44: message-id=<[email protected]> Jun 5 03:12:02 mail04 postfix/qmgr[76377]: 8EB992EFBB44: from=<[email protected]>, size=48845, nrcpt=1 (queue active) Jun 5 03:15:12 mail04 postfix/smtp[35058]: 8EB992EFBB44: to=<[email protected]>, relay=mx.baz.com[xxx.xxx.xxx.xxx]:25, conn_use=70, delay=343, delays=153/190/0/0.24, dsn=2.0.0, status=sent (250 ok) Jun 5 03:15:12 mail04 postfix/qmgr[76377]: 8EB992EFBB44: removed "Broken" log: <server># grep F3C362EF37CA postfix_log/mail04.log Jun 5 04:03:27 mail04 postfix/smtpd[39666]: F3C362EF37CA: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 5 04:03:27 mail04 postfix/cleanup[41287]: F3C362EF37CA: message-id=<[email protected]> Jun 5 04:03:28 mail04 postfix/qmgr[76377]: F3C362EF37CA: from=<[email protected]>, size=48892, nrcpt=1 (queue active) ** here should be a log line from postfix/smtp but there is none ** Jun 5 04:03:29 mail04 postfix/qmgr[76377]: F3C362EF37CA: removed Background information: system: FreeBSD xxx.xxx.xxx 8.2-RELEASE FreeBSD 8.2-RELEASE #0: Thu Feb 17 02:41:51 UTC 2011 [email protected]:/usr/obj/usr/src/sys/GENERIC amd64 Postfix is installed inside jail. Logs are on the same machine, log dir is mounted thru nullfs. The site has spikes of heavy load, causing disks (local) to run at 100%. Update The log is rotated daily, current size is ~ 500MB. I made a test by queuing 99000 messages to same destination (in order to rule out dns/network/mx issues). 5715 messages don't have any DSN record. Failed messages queue time is spread evenly over time, i don't see any time-bound issues. Some undelivered emails: envelopeid | processed_time --------------+---------------------------- 8D7652EF3BAE | 2012-06-06 13:19:11.072715 DD53A2EF3C5C | 2012-06-06 13:33:24.374783 8C52F2EF4E3F | 2012-06-06 13:39:15.810616 BBC572EF525C | 2012-06-06 13:44:22.762812 E95822EF54D1 | 2012-06-06 13:52:01.134533 839DD2EF4FBB | 2012-06-06 14:13:48.511236 017EE2EF6234 | 2012-06-06 15:04:48.618963 Those are a few picks, such records of undelivered email occur almost every second. <server># egrep '(8D7652EF3BAE|BBC572EF525C|017EE2EF6234)' mail04.log Jun 6 13:19:10 mail04 postfix/smtpd[20350]: 8D7652EF3BAE: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 13:19:10 mail04 postfix/cleanup[21024]: 8D7652EF3BAE: message-id=<[email protected]> Jun 6 13:19:10 mail04 postfix/qmgr[7939]: 8D7652EF3BAE: from=<[email protected]>, size=63718, nrcpt=1 (queue active) Jun 6 13:19:11 mail04 postfix/qmgr[7939]: 8D7652EF3BAE: removed Jun 6 13:44:22 mail04 postfix/smtpd[20346]: BBC572EF525C: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 13:44:22 mail04 postfix/cleanup[24811]: BBC572EF525C: message-id=<[email protected]> Jun 6 13:44:22 mail04 postfix/qmgr[7939]: BBC572EF525C: from=<[email protected]>, size=63758, nrcpt=1 (queue active) Jun 6 15:04:49 mail04 postfix/smtpd[20344]: 017EE2EF6234: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 15:04:49 mail04 postfix/cleanup[35585]: 017EE2EF6234: message-id=<[email protected]> Jun 6 15:04:49 mail04 postfix/qmgr[7939]: 017EE2EF6234: from=<[email protected]>, size=63706, nrcpt=1 (queue active) <server># <server># find /var/spool/postfix/active/ -type f -print | wc -l 1 <server># IMPORTANT: As you can see above some of emails doesn't event have the removed line.

  Read the article

• How to delete files and folders that cannot be deleted?

  - by glenneroo

  I have a backup copy of a previous Windows' Documents and Settings folder which only contains my original user and within 2 more directories: Favorites and Local Settings. When I try to delete Local Settings I get this error: When I try to delete Favorites, I get this error: I ran this in a cmd shell: attrib *.* -r -a -s -h /s ...but it did not help, nor did it return any errors/warnings. I used Unlocker v1.8.5 and LockHunter repeatedly at multiple levels to see if any files are in use, but both always say: No Files Locked. Update #1: I was able to rename the directory, which now gives me this warning before (trying to) delete: If I press Yes (or Yes to All) then I get this error: Update #2: I let chkdsk /f run which required a reboot since it's on my primary system partition. During Stage 2 scanning, I received about 40 of these: Deleting an index entry from index $0 of file 25. ...followed by: Deleting index entry cookies in index $I30 of file 37576. ...but I still get the first error dialog above when trying to delete. I ran chkdsk again, this time: chkdsk /f /r. Produced no messages. Same result when deleting. Update #3: Digging deeper, the 99 is the name of one of many directories located deep in here: C:\Documents and Settings.OLD\User\Local Settings\Application Data\Microsoft\Messenger\[email protected]\SharingMetadata\[email protected]\DFSR\Staging\CS{D4E4AE55-B5E2-F03B-5189-6C4DA6E41788}\ Inside each of those directories were files with names such as: 2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-Downloaded.frx I noticed that, unlike all the directories, I couldn't rename any of these files. I also noticed that the file + dir names were extremely long: Original directory = 194 characters Filenames = 100+ characters Together the length exceeds the 255-char limit which is bad and would explain the error message I posted in Update #1. Partial Solution: Rename all directories until the total path length is less than 100. Afterwards I was able to rename the .frx files, not to mention delete everything inside the Local Settings directory. This is only a partial solution because these (empty) directories are still not deleteable, C:\1\2\Favorites\Wien\What To Do.. C:\1\2\Favorites\Photography\FIRE Same error as above: Here is what Explorer properties shows for both folders: Update #4 (another partial solution): Using harrymc's answer combined with thoroughly reading through this amazing MS-KB article which contains nearly everyone's idea and then some, inconspicuously titled: You cannot delete a file or a folder on an NTFS file system volume. I was able to delete the 2nd folder C:\1\2\Favorites\Photography\FIRE - the problem being that there was an invisible trailing space at the end. I got lucky when I did an auto-complete whilst playing around with the del "\\?\<path>" command which he suggested. NOTE: A normal del did NOT work, nor did deleting from explorer. Now all that is left is the first directory C:\1\2\Favorites\Wien\What To Do.. (yes I tried endlessly with multiple combinations of the above solution ;) Keep 'em coming! =)

  Read the article

• Linux software RAID6: rebuild slow

  - by Ole Tange

  I am trying to find the bottleneck in the rebuilding of a software raid6. ## Pause rebuilding when measuring raw I/O performance # echo 1 > /proc/sys/dev/raid/speed_limit_min # echo 1 > /proc/sys/dev/raid/speed_limit_max ## Drop caches so that does not interfere with measuring # sync ; echo 3 | tee /proc/sys/vm/drop_caches >/dev/null # time parallel -j0 "dd if=/dev/{} bs=256k count=4000 | cat >/dev/null" ::: sdbd sdbc sdbf sdbm sdbl sdbk sdbe sdbj sdbh sdbg 4000+0 records in 4000+0 records out 1048576000 bytes (1.0 GB) copied, 7.30336 s, 144 MB/s [... similar for each disk ...] # time parallel -j0 "dd if=/dev/{} skip=15000000 bs=256k count=4000 | cat >/dev/null" ::: sdbd sdbc sdbf sdbm sdbl sdbk sdbe sdbj sdbh sdbg 4000+0 records in 4000+0 records out 1048576000 bytes (1.0 GB) copied, 12.7991 s, 81.9 MB/s [... similar for each disk ...] So we can read sequentially at 140 MB/s in the outer tracks and 82 MB/s in the inner tracks on all the drives simultaneously. Sequential write performance is similar. This would lead me to expect a rebuild speed of 82 MB/s or more. # echo 800000 > /proc/sys/dev/raid/speed_limit_min # echo 800000 > /proc/sys/dev/raid/speed_limit_max # cat /proc/mdstat md2 : active raid6 sdbd[10](S) sdbc[9] sdbf[0] sdbm[8] sdbl[7] sdbk[6] sdbe[11] sdbj[4] sdbi[3](F) sdbh[2] sdbg[1] 27349121408 blocks super 1.2 level 6, 128k chunk, algorithm 2 [9/8] [UUU_UUUUU] [=========>...........] recovery = 47.3% (1849905884/3907017344) finish=855.9min speed=40054K/sec But we only get 40 MB/s. And often this drops to 30 MB/s. # iostat -dkx 1 sdbc 0.00 8023.00 0.00 329.00 0.00 33408.00 203.09 0.70 2.12 1.06 34.80 sdbd 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sdbe 13.00 0.00 8334.00 0.00 33388.00 0.00 8.01 0.65 0.08 0.06 47.20 sdbf 0.00 0.00 8348.00 0.00 33388.00 0.00 8.00 0.58 0.07 0.06 48.00 sdbg 16.00 0.00 8331.00 0.00 33388.00 0.00 8.02 0.71 0.09 0.06 48.80 sdbh 961.00 0.00 8314.00 0.00 37100.00 0.00 8.92 0.93 0.11 0.07 54.80 sdbj 70.00 0.00 8276.00 0.00 33384.00 0.00 8.07 0.78 0.10 0.06 48.40 sdbk 124.00 0.00 8221.00 0.00 33380.00 0.00 8.12 0.88 0.11 0.06 47.20 sdbl 83.00 0.00 8262.00 0.00 33380.00 0.00 8.08 0.96 0.12 0.06 47.60 sdbm 0.00 0.00 8344.00 0.00 33376.00 0.00 8.00 0.56 0.07 0.06 47.60 iostat says the disks are not 100% busy (but only 40-50%). This fits with the hypothesis that the max is around 80 MB/s. Since this is software raid the limiting factor could be CPU. top says: PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 38520 root 20 0 0 0 0 R 64 0.0 2947:50 md2_raid6 6117 root 20 0 0 0 0 D 53 0.0 473:25.96 md2_resync So md2_raid6 and md2_resync are clearly busy taking up 64% and 53% of a CPU respectively, but not near 100%. The chunk size (128k) of the RAID was chosen after measuring which chunksize gave the least CPU penalty. If this speed is normal: What is the limiting factor? Can I measure that? If this speed is not normal: How can I find the limiting factor? Can I change that?

  Read the article

• what is best config for nginx worker_rlimit_nofile and worker_connections 28672

  - by Binh Nguyen

  i have issue of web-brower response ( especially on ie ) very slow, some time time out, and sometime hang out up to 20 seconds for one file redirect 301 when test with "f12 derverloper tool of ie" .. it report wait/start time very long. but after got connected the elements on web weill be dowload and show out fast ( test at xaluan.com ) It most happen when active user on web more than 2100 ( use google real time live analytic ). server running cenos 5 with ngix, apache, 32core cpu, 96G ram, raid 10 sas hdd.. == flowing is my config == user nobody; # no need for more workers in the proxy mode worker_processes 28; #old 32 #good at 24 error_log /var/log/nginx/error.log; #old add in end: info worker_rlimit_nofile 22528; events { worker_connections 22528; use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 25; #old 5 gzip on; #old on gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; ignore_invalid_headers on; client_header_timeout 1m; #3m client_body_timeout 1m; #3m send_timeout 1m; #3m reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 100M; client_body_buffer_size 256k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; limit_conn_zone $binary_remote_addr zone=limit_per_ip:1m; limit_conn limit_per_ip 20; limit_req_zone $binary_remote_addr zone=allips:5m rate=200r/s; limit_req zone=allips burst=200 nodelay; include "/etc/nginx/vhosts/*"; } =========== I have play around with worker config 1- tried increase as some one suggess: worker_rlimit_nofile = worker_connections = worker_processes * 1024 = 32768 2- tried to set low: worker_processes = 28 and other worker at 22582 and other solution too .. but not work cause some time it make server load hight very quick 3- tried to comment out the # worker_rlimit_nofile . so it will be unlimited. it look like solved a bit about issue response time. but it also make server high load quick in peak time... Please help thanks PS: other apache you may have look for help me out thanks Listen 0.0.0.0:8081 User nobody Group nobody ExtendedStatus On ServerAdmin [email protected] ServerName server.xaluan.com LogLevel warn # These can be set in WHM under 'Apache Global Configuration' Timeout 100 TraceEnable Off ServerSignature Off ServerTokens ProductOnly FileETag None StartServers 15 <IfModule prefork.c> MinSpareServers 20 MaxSpareServers 50 #MaxSpareServers 40 </IfModule> ServerLimit 1572 MaxClients 1572 MaxRequestsPerChild 4000 # MaxRequestsPerChild 3000 KeepAlive On KeepAliveTimeout 3 MaxKeepAliveRequests 300 #MaxKeepAliveRequests 130

  Read the article

• Tomcat and ASP site under IIS6 with SSL

  - by Rafe

  I've been working on migrating our companies' website from it's original server to a new one and am having two different but possibly related problems. The box this is sitting on is a Windows 2003 server x64 running IIS 6. The Tomcat version is 5.5.x as it was the version the original deployment was built on. There are two other sites on the server one in plain HTML, another in PHP and the one I am trying to migrate is a combination of Java and ASP (the introductory/sign in pages being Java as well as many reports used for our clients and the administration pages being in ASP) First of all I can only access the site if I enter the ip followed by :8080 (xxx.xxx.xxx.xxx:8080). The original setup had an index.html file in the root of the site with a bit of javascript in the header that pointed the site to 'www.mysite.com/app/public' but if I try going directly to the site without the 8080 I get a 'page not found error' and the javascript redirector causes the same problem because it doesn't add the 8080 into the URL even though on the original site the 8080 wasn't present so I don't understand why it would need it now. The js redirect looks like this: <script language="JavaScript"> <!-- location.href = "/app/public/" location.replace("/app/public/"); //--> </script> When setting the site up I used the command line to unbind IIS from all of the ip's on the system (there are 12 ip's on this box) because I was led to believe Tomcat wanted to use localhost which wasn't accessible. I'm not sure if this was the right thing to do but I'm throwing it in for the sake of completeness. And actually, at this point trying to go to localhost from the server itself throws up a 'could not connect to localhost' error. If I go to localhost:8080 I get the tomcat welcome page. If I do localhost:8080/app/public I get the intro page to our website. So I'm not sure what I'm even looking at in this case, that is what the proper behavior should be. The second part of the problem is that if I do go to either the ip or localhost such as above (localhost:8080/app/public) and click on our login link it is supposed to transfer me to our login page yet instead I receive a 'could not connect' error and the url has changed to localhost:8443/app/secure. From my research I see that port 8443 is Tomcats SSL port and the server.xml alludes to it as follows: <Connector port="8080" maxHttpHeaderSize="8192" maxThreads="150" minSpareThreads="25" maxSpareThreads="75" enableLookups="false" redirectPort="8443" acceptCount="100" connectionTimeout="20000" disableUploadTimeout="true" /> I have an SSL certificate assigned to the site via IIS and was under the impression that by default Tomcat allowed IIS to handle secure connections but apparently something is munged because it's not working. There is another section in the server.xml that reads like this: <Connector port="8009" enableLookups="false" redirectPort="443" protocol="AJP/1.3" /> Which I'm not sure what it is for although port 443 is the SSL port that IIS uses so I'm confused as to what this is supposed to be doing. Another question I have is when does the isap_redirector actually come into play? How does it know when to try and serve pages through Tomcat and when not to? I've hunted around the 'net for an answer and have yet to find a clear dialogue on the subject. Anyone have any pointers as to where to look for a solution to all of this?

  Read the article

• Outlook Web Access, reverse proxy and browser

  - by M'vy

  Hi SF'ers! We recently moved an exchange server behind a reverse proxy due to the loss of a public IP. I've managed to configure the reverse proxy (httpd proxy_http). But there is a problem for the SSL configuration. When accessing the OWA interface with Firefox, all is ok and working. When accessing with MSIE or Chrome, they do not retrieve the good SSL Certificate. I think this is due to the multiples virtual host for httpd. Is there a workaround to make sure MSIE/Chrome request the certificate for the good domain name like FF does? Already tested with the SSL virtual host : SetEnvIf User-Agent ".*MSIE.*" value BrowserMSIE Header unset WWW-Authenticate Header add WWW-Authenticate "Basic realm=exchange.domain.com" A: ProxyPreserveHost On also: BrowserMatch ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 Or: SetEnvIf User-Agent ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 And lots of ProxyPassand ProxyReversePath on /exchweb /exchange /public etc... And it still don't seem to work. Any clue? Thanks. Edit 1: Precision of versions # openssl version OpenSSL 0.9.8k-fips 25 Mar 2009 /usr/sbin/httpd -v Server version: Apache/2.2.11 (Unix) Server built: Mar 17 2009 09:15:10 Browser versions : MSIE : 8.0.6001 Opera: Version 11.01 Revision 1190 Firefox: 3.6.15 Chrome: 10.0.648.151 Operating System: Windows Vista 32bits. They are all SNI compliant, I've tested them this afternoon https://sni.velox.ch/ You're right Shane Madden, I have multiple sites on the same public IP (and same port as well). The server itself is just a reverse proxy, that rewrite addresses to internal servers. The default host is a dev site, configure with the certificate that does not match the OWA (of course... would have been to easy) <VirtualHost *:443> ServerName dev2.domain.com ServerAdmin [email protected] CustomLog "| /usr/sbin/rotatelogs /var/log/httpd/access-%y%m%d.log 86400" combined ErrorLog "| /usr/sbin/rotatelogs /var/log/httpd/error-%y%m%d.log 86400" LogLevel warn RewriteEngine on SetEnvIfNoCase X-Forwarded-For .+ proxy=yes SSLEngine on SSLProtocol -all +SSLv3 +TLSv1 SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL:+SSLv3 SSLCertificateFile /etc/httpd/ssl/domain.com.crt SSLCertificateKeyFile /etc/httpd/ssl/domain.com.key RewriteCond %{HTTP_HOST} dev2\.domain\.com RewriteRule ^/(.*)$ http://dev2.domain.com/$1 [L,P] </VirtualHost> The certificate of domain is a *.domain.com The second vHost is : <VirtualHost *:443> ServerName exchange.domain2.com ServerAdmin [email protected] CustomLog "| /usr/sbin/rotatelogs /var/log/httpd/exchange/access-%y%m%d.log 86400" combined ErrorLog "| /usr/sbin/rotatelogs /var/log/httpd/exchange/error-%y%m%d.log 86400" LogLevel warn SSLEngine on SSLProxyEngine On SSLProtocol -all +SSLv3 +TLSv1 SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL:+SSLv3 SSLCertificateFile /etc/httpd/ssl/exchange.pem SSLCertificateKeyFile /etc/httpd/ssl/exchange.key RewriteEngine on SetEnvIfNoCase X-Forwarded-For .+ proxy=yes RewriteCond %{HTTP_HOST} exchange\.domain2\.com RewriteRule ^/(.*)$ https://exchange.domain2.com/$1 [L,P] </VirtualHost> and it's certificate is exchange.domain2.com only. I presume the SNI is somewhere not activated on my server. The versions of openssl and apache seams to be ok for the SNI support. The only thing I do not know is if httpd has been compile with the good options. (I assume it's a fedora packet).

  Read the article

• Why don't mails show up in the recipient's mailspool?

  - by Jason

  I have postfix dovecot running with local email system on thunderbird. I have two users on by ubuntu, mailuser 1 and mailuser 2 whom i added to thunderbird. Everything went fine, except the users dont have anything on their inbox on thunderbird and sent mails dont get through. Im using maildir as well. Checking /var/log/mail.log reveals this This what is happining: Restarting postfix and dovecot and then sending mail from one user to another user... I believe this line is the problem May 30 18:31:55 postfix/smtpd[12804]: disconnect from localhost[127.0.0.1] Why is it not connecting ? What could be wrong ? /var/log/mail.log May 30 18:30:21 dovecot: imap: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: master: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: imap: Server shutting down. in=467 out=475 May 30 18:30:21 dovecot: config: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: log: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: anvil: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: master: Dovecot v2.2.9 starting up (core dumps disabled) May 30 18:30:54 dovecot: imap-login: Login: user=<mailuser2>, method=PLAIN, rip=::1, lip=::1, mpid=12638, TLS, session=<xUfQkaD66gAAAAAAAAAAAAAAAAAAAAAB> May 30 18:31:04 postfix/master[12245]: terminating on signal 15 May 30 18:31:04 postfix/master[12795]: daemon started -- version 2.11.0, configuration /etc/postfix May 30 18:31:55 postfix/postscreen[12803]: CONNECT from [127.0.0.1]:33668 to [127.0.0.1]:25 May 30 18:31:55 postfix/postscreen[12803]: WHITELISTED [127.0.0.1]:33668 May 30 18:31:55 postfix/smtpd[12804]: connect from localhost[127.0.0.1] May 30 18:31:55 postfix/smtpd[12804]: 1ED7120EB9: client=localhost[127.0.0.1] May 30 18:31:55 postfix/cleanup[12809]: 1ED7120EB9: message-id=<[email protected]> May 30 18:31:55 postfix/qmgr[12799]: 1ED7120EB9: from=<[email protected]>, size=546, nrcpt=1 (queue active) May 30 18:31:55 postfix/local[12810]: 1ED7120EB9: to=<mailuser2@mysitecom>, relay=local, delay=0.03, delays=0.02/0.01/0/0, dsn=2.0.0, status=sent (delivered to maildir) May 30 18:31:55 postfix/qmgr[12799]: 1ED7120EB9: removed May 30 18:31:55 postfix/smtpd[12804]: disconnect from localhost[127.0.0.1] May 30 18:31:55 dovecot: imap-login: Login: user=<mailuser1>, method=PLAIN, rip=127.0.0.1, lip=127.0.0.1, mpid=12814, TLS, session=<sD9plaD6PgB/AAAB> This is my postfix main.cf See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. smtpd_relay_restrictions = permit_mynetworks permit_sasl_authenticated defer_unauth_destination myhostname = server mydomain = mysite.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = $mydomain mydestination = mysite.com #relayhost = smtp.192.168.10.1.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 192.168.10.0/24 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all home_mailbox = Maildir / mailbox_command= All ports are listening tcp 0 0 *:imaps *:* LISTEN tcp 0 0 *:submission *:* LISTEN tcp 0 0 *:imap2 *:* LISTEN tcp 0 0 s148134.s148134.:domain *:* LISTEN tcp 0 0 192.168.56.101:domain *:* LISTEN tcp 0 0 10.0.2.15:domain *:* LISTEN tcp 0 0 localhost:domain *:* LISTEN tcp 0 0 *:ssh *:* LISTEN tcp 0 0 *:smtp *:* LISTEN tcp 0 0 localhost:953 *:* LISTEN tcp6 0 0 [::]:imaps [::]:* LISTEN tcp6 0 0 [::]:submission [::]:* LISTEN tcp6 0 0 [::]:imap2 [::]:* LISTEN tcp6 0 0 [::]:domain [::]:* LISTEN tcp6 0 0 [::]:ssh [::]:* LISTEN tcp6 0 0 [::]:smtp [::]:* LISTEN tcp6 0 0 localhost:953 [::]:* LISTEN

  Read the article

• NPM not installing dependencies?

  - by neezer

  Having trouble getting NPM to install dependencies with npm install -d in my project directory with a defined package.json file. Here's my package.json: https://gist.github.com/3068312 And after wiping my project root's node modules folder (rm -rf node_modules), I run npm install -d in my project root and am greeted with this: (ssh) /vagrant git:master ? npm install -d npm info it worked if it ends with ok npm info using [email protected] npm info using [email protected] npm info preinstall [email protected] npm http GET https://registry.npmjs.org/sinon npm http GET https://registry.npmjs.org/underscore npm http GET https://registry.npmjs.org/mocha npm http GET https://registry.npmjs.org/request npm http 304 https://registry.npmjs.org/sinon npm http 304 https://registry.npmjs.org/underscore npm http 304 https://registry.npmjs.org/mocha npm http 304 https://registry.npmjs.org/request npm info into /vagrant [email protected] npm info into /vagrant [email protected] npm info into /vagrant [email protected] npm info into /vagrant [email protected] npm info installOne [email protected] npm info installOne [email protected] npm info installOne [email protected] npm info installOne [email protected] npm info unbuild /vagrant/node_modules/underscore npm info unbuild /vagrant/node_modules/mocha npm info unbuild /vagrant/node_modules/sinon npm info unbuild /vagrant/node_modules/request npm ERR! error installing [email protected] npm info unbuild /vagrant/node_modules/underscore npm ERR! error rolling back [email protected] Error: UNKNOWN, unknown error '/vagrant/node_modules/underscore' npm ERR! Error: ENOENT, no such file or directory '/vagrant/node_modules/underscore/package.json' npm ERR! You may report this log at: npm ERR! <http://bugs.debian.org/npm> npm ERR! or use npm ERR! reportbug --attach /vagrant/npm-debug.log npm npm ERR! npm ERR! System Linux 3.2.0-23-generic npm ERR! command "node" "/usr/bin/npm" "install" "-d" npm ERR! cwd /vagrant npm ERR! node -v v0.6.12 npm ERR! npm -v 1.1.4 npm ERR! path /vagrant/node_modules/underscore/package.json npm ERR! code ENOENT npm ERR! message ENOENT, no such file or directory '/vagrant/node_modules/underscore/package.json' npm ERR! errno {} npm ERR! error installing [email protected] npm info unbuild /vagrant/node_modules/request npm ERR! error rolling back [email protected] Error: UNKNOWN, unknown error '/vagrant/node_modules/request' npm ERR! npm ERR! Additional logging details can be found in: npm ERR! /vagrant/npm-debug.log npm not ok If I rerun npm install -d, the error changes to whatever the next package is... if I keep running it it over and over again, it eventually doesn't complain anymore and outputs: (ssh) /vagrant git:master ? npm install -d npm info it worked if it ends with ok npm info using [email protected] npm info using [email protected] npm info preinstall [email protected] npm info build /vagrant npm info linkStuff [email protected] npm info install [email protected] npm info postinstall [email protected] npm info ok However, none of the dependencies for any of these packages get installed. For instance, cheerio has a few dependencies, so when I try running my test suite, I'm greeted with: (ssh) /vagrant git:master ? mocha --compilers coffee:coffee-script --watch spec/* node.js:201 throw e; // process.nextTick error, or 'error' event on first tick ^ Error: Cannot find module 'cheerio-select' at Function._resolveFilename (module.js:332:11) at Function._load (module.js:279:25) at Module.require (module.js:354:17) What gives? I'm on Ubuntu Precise64 in a Vagrant virtual box.

  Read the article

• Where is my VMware-ws FreeNAS CIFS(ZFS) bottle-neck?

  - by maka

  Background: I'm building a quiet HTPC + NAS that is also supposed to be used for general computer usage. I'm so far generally happy with things, it was just that I was expecting a little better IO performance. I have no clue if my expectations are unreal. The NAS is there as a general purpose file storage and as a media server for XBMC and other devices. ZFS is a requirement. Question: Where is my bottle-neck, and is there anything I can do config wise, to improve my performance? I'm thinking VM-disk settings could be something but I really have no idea where to go since I'm neither experienced with FreeNAS nor VMware-WS. Tests: When I'm on the host OS and copy files (from the SSD) to the CIFS share, I get around 30 Mbytes/sec read and write. When I'm on my laptop laptop, wired to the network, I get about the same specs. The test I've done are with a 16 GB ISO, and with about 200 MB of RARs and I've tried avoiding the RAM-cache by reading different files than the ones I'm writing ( 10 GB). It feels like having less CPU cores is a lot more efficient, since the resource manager in Windows reports less CPU-usage. With 4 cores in VMware, CPU usage was 50-80%, with 1 core it was 25-60%. EDIT: HD ActiveTime was quite high on SSD so I moved the page file, disabled hibernate and enabled Win DiskCache both on SSD and RAID. This resulted in no real performance difference for one file, but if i transferred 2 files the total speed went up to 50 Mbytes/s vs ~40. The ActiveTime avg also went down a lot (to ~20%) but has now higher bursts. DiskIO is on ~ 30-35 Mbytes/s avgs, with ~100Mb bursts. Network is on 200-250Mbits/s with ~45 active TCP connections. Hardware Asus F2A85-M Pro A10-5700 16GB DDR3 1600 OCZ Vertex 2 128GB SSD 2x Generic 1tb 7200 RPM drives as RAID0 (in win7) Intel Gigabit Desktop CT Software Host OS: Win7 (SSD) VMware Worksation 9 (SSD) FreeNAS 8.3 VM (20GB VDisk on SSD) CPU: I've tried 1, 2 and 4 cores. Virtualisation engine, Preferred mode: Automatic 10,24Gb ram 50Gb SCSI VDisk on the RAID0, VDisk is formatted as ZFS and exposed through CIFS through FreeNAS. NIC Bridge, Replicate physical network state Below are two typical process print-outs while I'm transfering one file to the CIFS share. last pid: 2707; load averages: 0.60, 0.43, 0.24 up 0+00:07:05 00:34:26 32 processes: 2 running, 30 sleeping Mem: 101M Active, 53M Inact, 1620M Wired, 2188K Cache, 149M Buf, 8117M Free Swap: 4096M Total, 4096M Free PID USERNAME THR PRI NICE SIZE RES STATE TIME WCPU COMMAND 2640 root 1 102 0 50164K 10364K RUN 0:25 25.98% smbd 1897 root 6 44 0 168M 74808K uwait 0:02 0.00% python last pid: 2746; load averages: 0.93, 0.60, 0.33 up 0+00:08:53 00:36:14 33 processes: 2 running, 31 sleeping Mem: 101M Active, 53M Inact, 4722M Wired, 2188K Cache, 152M Buf, 5015M Free Swap: 4096M Total, 4096M Free PID USERNAME THR PRI NICE SIZE RES STATE TIME WCPU COMMAND 2640 root 1 76 0 50164K 10364K RUN 0:52 16.99% smbd 1897 root 6 44 0 168M 74816K uwait 0:02 0.00% python I'm sorry if my question isn't phrased right, I'm really bad at these kind of things, and it is the first time I post here at SU. I also appreciate any other suggestions to something, I could have missed.

  Read the article

• Rosewill RSV-S5 and it's transferespeeds

  - by DoomStone

  I have just bought a Rosewill RSV-S5, I have installed 5x1,5Tb Western Digital Green disks in it. After that have I created a Raid5 on them all with the software that followed with the hardware. Not the raid it self works fine, but it is SLOW, I can only obtain a maximum of 25 MB/s, and if SABnzbd+ is downloading with 5 MB/s is it having a hard time streaming a normal DIVX (700 mb) movie. Is this normal or is there something wrong? Edit: should be able to handle 3 Gbps = 384 megabytes / second Edit 2: As you can see am I only downloading with 3,76 MB/s and I'm trying to watch V s02e08 (720p), but it is completely unwatchable, as I can see 30 sec, and the it buffers for 20 sec. Edit: Other information there might be required I'm running Windows Server 2008 R2, optimized for program performance. Windows is installed on a 60GB SSD. I have a 50 Mb/s internet connection and a 1 Gb/s LAN, all connected with Cat6 Ethernet cables. The MCE is using a Gigabyte EP35C-DS3R motherboard with 2 GB DDR2 ram. Edit 3: I have used chunk sizes for 128 KB Edit 4: I found this on newegg Pros: Enclosure for 5x2TB hard drive is fine. This is basically a rebranded San Digital TR5M-B product. For support Rosewill tells you to contact San Digital. No direct support from Silicon Image for the computer raid card. Cons: Includes computer Silicon Image 3132 raid card, extremely slow raid 5 write (our tests ~10MB/s). Compare to regular internal local drive write 30-60MB/s. We basically dumped the Sil3132 card and replaced with High Point RocketRaid 622 card for extra $69.99. Note for RR622, turn off ECRC (end to end CRC check) for card to work on IBM xserver. What took 12hrs to copy now took 2-3hrs. San Digital realized the problem and has the newer model TR5M-BP TowerRaid Plus that comes with High Point RocketRaid 622 card. Rosewill should discontinue this product and go with TR5M-BP. Could not get Silicon Image raid management software to work with complicated 2008R2 server with 10 NICs, application doesn't know how to talk to localhost port with all those NICs. No updates from Silicon Image and support from San Digital ignored. Gave up on Sil3132 card. Save yourself from a lot of headaches, get the RR622 card too if you are going to buy this product. Other Thoughts: The newer model is TR5M-BP TowerRaid Plus, comes with High Point RocketRaid 622 raid card for the PC instead of Silicon Image Sil3132. According to San Digital, raid 5 performance for Sil3132 read 80MB/s write 19MB/s, and RR622 read 154MB/s write 149MB/s. Our RR622 tests gave (8TB raid 5) write ~80-110MB/s copying 40GB file took 8mins. So I have now ordered a HighPoint RocketRAID 622 2P ext SATA III and hopes that it will solve my problems.

  Read the article

• VPS 512 MB RAM with WordPressMU comes to consumes lots of memory

  - by CAPitalZ

  I have googled for days and gathered all optimization suggestions and tried. My sites are not getting any high hits. May be like 100 hits per day [all my sites combined]. Here are my specs I have 512 MB RAM VPS with burstable 1024 MB. Centos 5 32-bit & cPanel/WHM Apache 2.2 MySQL 5.0 PHP 5.3.2 Here is my Configs I have 2 WordPressMU production sites, and 1 test site my.cnf # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /var/lib/mysql/mysql.sock # Here follows entries for some specific programs # The MySQL server [mysqld] port = 3306 socket = /var/lib/mysql/mysql.sock skip-locking skip-bdb skip-innodb key_buffer = 16M max_allowed_packet = 1M table_cache = 64 sort_buffer_size = 512K net_buffer_length = 8K read_buffer_size = 256K read_rnd_buffer_size = 512K myisam_sort_buffer_size = 8M #CAPitalZ thread_cache_size=8 thread_concurrency=4 #query_cache_type=1 #query_cache_limit=1M query_cache_size=16M concurrent_insert=2 low_priority_updates=1 max_connections=50 tmp_table_size=16M max_heap_table_size=16M join_buffer_size=1M interactive_timeout=25 wait_timeout=1000 #connect_timout=10 not able to restart mysql max_connect_errors=10 # Don't listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (via the "enable-named-pipe" option) will render mysqld useless! # skip-networking # Disable Federated by default skip-federated # Replication Master Server (default) # binary logging is required for replication log-bin=mysql-bin # required unique id between 1 and 2^32 - 1 # defaults to 1 if master-host is not set # but will not function as a master if omitted server-id = 1 [mysqld_safe] open_files_limit=8192 [mysqldump] quick max_allowed_packet = 16M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [isamchk] key_buffer = 20M sort_buffer_size = 20M read_buffer = 2M write_buffer = 2M [myisamchk] key_buffer = 20M sort_buffer_size = 20M read_buffer = 2M write_buffer = 2M [mysqlhotcopy] interactive-timeout httpd.conf I have unselected many modules and recompiled using EasyApache in WHM. Only have the following modules built Deflate Expires Fileprotect Imagemap MPM Prefork Version [default] EAccelerator for PHP Bcmath Calendar CurlSSL [I'm using Curl. But I don't have any https sites] Expat GD [for image cropping] Gettext Imap Mbregex [default] Mbstring [need both Mbregex and Mbstring for utf-8] Mysql of the system MySQL "Improved" extension. Sockets TTF (FreeType) [I'm using custom font] Zlib Under Global Configuration I only have FollowSymLinks enabled I Have TraceEnable, ServerSignature, FileETag OFF ServerTokens ProductOnly DirectoryIndex Priority has index.php as the first one I have removed Clamd [Clam Anti-virus] SpamAssasin is Off Under Tweak Settings Default catch-all/default address behavior for new accounts. This is set to "fail" All stats programs turned off I have eAccelerator installed and checked in phpinfo and its working [Pre VirtualHost Include under WHM] Timeout 20 KeepAlive On MaxKeepAliveRequests 200 KeepAliveTimeout 3 MinSpareServers 1 MaxSpareServers 3 StartServers 1 ServerLimit 50 MaxClients 50 MaxRequestsPerChild 4000 ExtendedStatus Off #ServerType standalone this throws error HostnameLookups Off <Directory "/"> AllowOverride None </Directory> My sites will take ages to load and WHM/CPanel will not even load. adadaa.com/ http://adadaa.net/ kadais.ca/ My average memory consumption is like 1000 MB! [yes always bursting] The process that consumes most CPU and also most memory is mysql But I also get like 15 httpd processes [when its bursting] I already got warning from cpuwatchcheck saying "While processing, the cpu has been maxed out for more than a 6 hour period. The current load/uptime line on the server at the time of this email is 07:00:37 up 11:30, 0 users, load average: 14.64, 16.79, 20.07" I don't know, I have tried switching these config values many different times, but nothing seems to work. Please show some light... Thanks

  Read the article

• How can I recover an ext4 filesystem corrupted after a fsck?

  - by Regan

  I have an ext4 filesystem on luks over software raid5. The filesystem was operating "just fine" for several years when I was beginning to run out of space. I had a 9T volume on 6x2T drives. I began upgrading to 3T drives by doing the mdadm fail, remove, add, rebuild, repeat process until I had a larger array. I then grew the luks container, and then when I unmounted and tried to resize2fs I was given the message the filesystem was dirty and needed e2fsck. Without thinking I just did e2fsck -y /dev/mapper/candybox and it began spewing all kinds of inode being removed type messages (can't remember exactly) I killed e2fsck and tried to remount the filesystem to backup data I was concerned about. When trying to mount at this point I get: # mount /dev/mapper/candybox /candybox mount: wrong fs type, bad option, bad superblock on /dev/mapper/candybox, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Looking back at my older logs I noticed the filesystem was giving this error each time the machine booted: kernel: [79137.275531] EXT4-fs (dm-2): warning: mounting fs with errors, running e2fsck is recommended So shame on me for not paying attention :( I then tried to mount using every backup superblock (one after another) and each attempt left this in my log: EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 0 failed (26534!=65440) EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 1 failed (38021!=36729) EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 2 failed (18336!=39845) ... EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 11911 failed (28743!=44098) BUG: soft lockup - CPU#0 stuck for 23s! [mount:2939] Attempts to restart e2fsck results in: # e2fsck /dev/mapper/candybox e2fsck 1.41.14 (22-Dec-2010) e2fsck: Group descriptors look bad... trying backup blocks... candy: recovering journal e2fsck: unable to set superblock flags on candy At this point, I decided it best to order some more drives and make an image using ddrescue Now two weeks later I have an image of the luks partition in a .img file. # ls -lh total 14T -rw-r--r-- 1 root root 14T Oct 25 01:57 candybox.img -rw-r--r-- 1 root root 271 Oct 20 14:32 candybox.logfile After numerous attempts using everything I could find online I could not coerce e2fsck to do anything on the image, so I used mkfs.ext4 -L candy candybox.img -m 0 -S and I was able to mount the dirty filesystem readonly without the journal and recover 960G of data. It gave all kinds of errors of various directories not existing and so forth but I was able to get some stuff. Which gave me some hope! I then ran e2fsck again and it had to recreate the root inode and gave a massive list of correcting group counts, I accepted the root inode creation and said no to everything else, leaving a completely empty filesystem. Re-ran again and said yes to all questions with the same result but now a "clean" but empty filesystem. extundelete gives me 0 recoverable inodes found. And now I'm stuck again, I can't come up with any other methods other than dropping to something like photorec which will give me an absolute mess with how large the filesystem was. I'm willing to re-copy the image from the original array and start over, if I can get any suggestions or ideas on a way to get more of my files back. I wish I could give more detailed logs of the commands that have run, but the output is long scrolled passed except for what gets logged to syslog and my memory is not as detailed due to the timeframe this has occurred over. Any help is greatly appreciated!

  Read the article

• ISP 5 Device Limit ... again

  - by Tommo

  Sorry for the delay in responding to the suggestions that were posted in my first question (ISP 5 Device Limit - double NAT the solution?). I've been travelling and have not been able to try anything. Below is what I've tried and where I have not been successful. Any more help gratefully appreciated. I figure I need to give a more comprehensive overview of what I've got and how it's set up. First of all - I am using all Apple products here. I am iMac, iPad, iPhone, Apple TV, Airport Express and Time Capsule. I used to like the way that it 'just worked'. Now I find that it requires a bit of encouragement before it 'just works'. So, as I stated in my original question; my ISP has a router in my building that is limiting me to 5 devices. I am hard wired into this router and I can neither access it physically nor logically (they won't let me access it). Also, I only appear to be able to connect to it through the LAN ports on my Time Capsule. Any device I connect appears to be on a rolling IP list with the following settings: Router 91.72.80.1 Devices then get assigned IPv4 addresses in the range (as far as I can see) from 91.72.80.2 onwards. SubNet Mask 255.255.255.0 DNS Servers 213.132.63.25, 80.227.2.4 I have my Time Capsule / Router in Bridge-Mode which means I am limited to the 5 devices and cannot use Guest Networks etc. What I've tried today. Static IPs: On all devices, I went from DHCP to Static and put in the same information when they had connected using DHCP. Somewhat surprisingly this did not work. None of the devices enjoyed any connection to the router and certainly no internet connection. Intentional Double-NAT - Time Capsule to 'DHCP and NAT': By selecting DHCP and NAT on my Router I was able to connect devices to my Time Capsule in the range 10.0.1.2 to 10.0.1.200. This offered no internet connectivity and didn't really help the situation. In this mode, however, I was able to force the devices - individually and laboriously - to look for the Router and previously listed DNSs by inputting the numbers from 'Bridge-mode' into the STATIC settings and then resetting the connection. The Router then appeared to assign a distinct IP address to the device and it worked on the network. I had this working for more than 5 devices. However, this is not a great solution because as soon as one of the mobile devices left the building it needed repointing to the Router. The connections were also not very stable. Especially when trying to hold onto a VPN. Spoofing a few MAC addresses: I'm afraid I don't really know what this would achieve, nor how to do it on an Apple device… So … I'm almost back at Square One. I have had to withdraw to the Bridge-Mode position again with the 5 device limit to see if there's a better course of action to follow. ANY help would be much appreciated. I am positive that I cannot be the only one suffering under this 5 device limit!

  Read the article

• Configuring a PIX 506e for Asterisk

  - by orthogonal3

  Hi all! I'm having problems configuring a old Cisco PIX running 6.3 and wondered if anyone can lend a hand? Simply put I have a PIX 506e that I want to put in my VoIP data path. I can't update it and getting a compat version of Java for that version of PIX is tough so I can't log onto the web interface. The PIX straddles two networks..... 192.168.5.0 on the inside, ...50.0 on the outside both net masks are 255.255.255.0 I have a local Asterisk server cluster with a single service IP (<local asterisk>) SIP is on UDP 5060 and RTP (for the voip data) is on UDP 18000-18999 I know thats a big range but hey may as well. I need the 192.168.5.0 net to have web and ftp access for updates and the like. DHCP, DNS and NTP is already provided on that network so I don't need external DNS access. So I think I want the following rules: SIP or RTP from <my itsp> arriving at <outside voip ip> NATed to <local asterisk> SIP or RTP able to do the reverse route (should be covered by high sec - low sec??) HTTP and FTP access outbound for software update for the servers etc I have the following config at the minute - and I think I'm almost there (I hope)... interface ethernet0 auto interface ethernet1 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password wouldyouliketobeapeppertoo encrypted passwd wouldyouliketobeapeppertoo encrypted hostname afirewall domain-name adomain fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 access-list acl_ping permit icmp any any access-list voip permit ip host <my itsp> host <local asterisk> mtu outside 1500 mtu inside 1500 ip address outside <outside pix ip> 255.255.255.0 ip address inside <inside pix ip> 255.255.255.0 arp timeout 14400 global (outside) 1 <outside generic ip> nat (inside) 1 192.168.5.0 255.255.255.0 0 0 static (inside,outside) <outside voip ip> <local asterisk> netmask 255.255.255.255 0 0 static (outside,inside) <local asterisk> <outside voip ip> netmask 255.255.255.255 0 0 access-group acl_ping in interface outside access-group acl_ping in interface inside route outside 0.0.0.0 0.0.0.0 <my next hop router> 1 route outside <my itsp> 255.255.255.255 <my next hop router> 1 I think I just need a hand with the access-lists and NAT/static rules. Would anyone be able to help as I've RTFM'd the Cisco docs a few times and they're heavy. Wishing I'd completed my CCNA now! Thanks all for any help, Phil

  Read the article

• AMD Catalyst 13.9 installation failure

  - by Simon Verbeke

  Earlier today I installed Windows 8.1, and when I wanted to go into Catalyst Control Center, I noticed some odd error of CCC not being able to display options. I then figured I needed a driver update, so I downloaded the latest drivers, version 13.9, and tried to install them. While it was trying to install the display drivers, I got a blue screen. Tried again and got the same. Then I used an uninstall tool from AMD to remove all traces of my old drivers and tried to install the new drivers. Again, a blue screen. This is all I could think of to try. Would anyone know some other things I can try? EDIT: thought I might want to include the log entry for the crash: - <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> - <System> <Provider Name="Microsoft-Windows-WER-SystemErrorReporting" Guid="{ABCE23E7-DE45-4366-8631-84FA6C525952}" EventSourceName="BugCheck" /> <EventID Qualifiers="16384">1001</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2013-10-19T20:59:25.000000000Z" /> <EventRecordID>26587</EventRecordID> <Correlation /> <Execution ProcessID="0" ThreadID="0" /> <Channel>System</Channel> <Computer>Simon-PC</Computer> <Security /> </System> - <EventData> <Data Name="param1">0x0000007e (0xffffffffc0000005, 0xfffff80002a86dca, 0xffffd00025f250e8, 0xffffd00025f248f0)</Data> <Data Name="param2">C:\WINDOWS\MEMORY.DMP</Data> <Data Name="param3">101913-8953-01</Data> </EventData> </Event> Another edit: As it turns out, the graphics card isn't showing up any more in the device manager. But as far as I can tell, it is still working (the fans are spinning and my screen is plugged into that graphics card). This is solved. it appears that my graphics card is now running with a default windows driver. I also tried the forced method mentioned here: AMD Graphics Drivers won't install properly . But I still get a BSOD. Third edit: Slight succes! Managed to install version 13.4. Everything appears to be working fine now. I think I'm just going to skip version 13.9.

  Read the article

• got VPN l2l connect between a site & HQ but not traffice using ASA5505 on both ends

  - by vinlata

  Hi, Could anyone see what did I do wrong here? this is one configuration of site1 to HQ on ASA5505, I can get connected but seems like no traffic going (allowed) between them, could it be a NAT issue? any helps would much be appreciated Thanks interface Vlan1 nameif inside security-level 100 ip address 172.30.205.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address pppoe setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 shutdown ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! passwd .dIuXDIYzD6RSHz7 encrypted ftp mode passive dns server-group DefaultDNS domain-name errg.net object-group network HQ network-object 172.22.0.0 255.255.0.0 network-object 172.22.0.0 255.255.128.0 network-object 172.22.0.0 255.255.255.128 network-object 172.22.1.0 255.255.255.128 network-object 172.22.1.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list outside_access_in extended permit icmp any any echo-reply access-list outside_20_cryptomap extended permit ip 172.30.205.0 255.255.255.0 o bject-group HQ access-list inside_nat0_outbound extended permit ip 172.30.205.0 255.255.255.0 o bject-group HQ access-list policy-nat extended permit ip 172.30.205.0 255.255.255.0 172.22.0.0 255.255.0.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 nat-control global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) 172.30.205.0 access-list policy-nat access-group inside_access_in in interface inside access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute username errgadmin password Os98gTdF8BZ0X2Px encrypted privilege 15 http server enable http 64.42.2.224 255.255.255.240 outside http 172.22.0.0 255.255.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 190 match address outside_20_cryptomap crypto map outside_map 190 set pfs crypto map outside_map 190 set peer 66.7.249.109 crypto map outside_map 190 set transform-set ESP-3DES-SHA crypto map outside_map 190 set phase1-mode aggressive crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 30 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp nat-traversal 190 crypto isakmp ipsec-over-tcp port 10000 tunnel-group 66.7.249.109 type ipsec-l2l tunnel-group 66.7.249.109 ipsec-attributes pre-shared-key * telnet timeout 5 ssh 172.30.205.0 255.255.255.0 inside ssh 172.22.0.0 255.255.0.0 outside ssh 64.42.2.224 255.255.255.240 outside ssh 172.25.0.0 255.255.128.0 outside ssh timeout 5 console timeout 0 management-access inside vpdn group PPPoEx request dialout pppoe vpdn group PPPoEx localname [email protected] vpdn group PPPoEx ppp authentication pap vpdn username [email protected] password ********* dhcpd address 172.30.205.100-172.30.205.131 inside dhcpd dns 172.22.0.133 68.94.156.1 interface inside dhcpd wins 172.22.0.133 interface inside dhcpd domain errg.net interface inside dhcpd enable inside ! ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! end

  Read the article

• "ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver" wheel-click is wrong

  - by sputnick

  I use this mouse under archlinux x86_64 with 3.2.8-1-ARCH kernel. I have some problems to select and then paste with the wheel-click in some applications like konversation, not in a terminal nor an editor. I don't know if it's a hardware problem or a software one. $ lsusb -v Bus 002 Device 110: ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x046d Logitech, Inc. idProduct 0xc50e Cordless Mouse Receiver bcdDevice 25.10 iManufacturer 1 Logitech iProduct 2 USB RECEIVER iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 34 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 70mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 2 Mouse iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.11 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 95 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Device Status: 0x0000 (Bus Powered) When I see what's happens in xev, the output is different compared to another mouse My buggy Logitech mouse : ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350700, (48,52), root:(1491,75), state 0x10, button 11, same_screen YES EnterNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170350700, (48,52), root:(1491,75), mode NotifyGrab, detail NotifyInferior, same_screen YES, focus YES, state 16 KeymapNotify event, serial 40, synthetic NO, window 0x0, keys: 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350716, (48,52), root:(1491,75), state 0x10, button 6, same_screen YES ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350716, (48,52), root:(1491,75), state 0x10, button 6, same_screen YES ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350988, (48,52), root:(1491,75), state 0x10, button 11, same_screen YES LeaveNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170350988, (48,52), root:(1491,75), mode NotifyUngrab, detail NotifyInferior, same_screen YES, focus YES, state 16 a working mouse (dell) : ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170245131, (46,32), root:(1489,55), state 0x10, button 2, same_screen YES EnterNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170245131, (46,32), root:(1489,55), mode NotifyGrab, detail NotifyInferior, same_screen YES, focus YES, state 528 KeymapNotify event, serial 40, synthetic NO, window 0x0, keys: 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170245411, (46,32), root:(1489,55), state 0x210, button 2, same_screen YES LeaveNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170245411, (46,32), root:(1489,55), mode NotifyUngrab, detail NotifyInferior, same_screen YES, focus YES, state 16 A demo of the problem when I use konversation (IRC) : http://www.youtube.com/watch?v=lhmr92M7NCc I tried to modify the button map with xmodmap like this with no success (one at a time) : xmodmap -e "pointer = 1 0 3" xmodmap -e "pointer = 1 1 3" xmodmap -e "pointer = 1 2 3" xmodmap -e "pointer = 1 3 3" xmodmap -e "pointer = 1 4 3" xmodmap -e "pointer = 1 5 3" xmodmap -e "pointer = 1 6 3" xmodmap -e "pointer = 1 7 3" xmodmap -e "pointer = 1 8 3" xmodmap -e "pointer = 1 9 3" xmodmap -e "pointer = 1 10 3" xmodmap -e "pointer = 1 11 3" xmodmap -e "pointer = 1 12 3" xmodmap -e "pointer = 1 13 3" xmodmap -e "pointer = 1 14 3" xmodmap -e "pointer = 1 15 3" xmodmap -e "pointer = 1 16 3" xmodmap -e "pointer = 1 17 3" xmodmap -e "pointer = 1 18 3" xmodmap -e "pointer = 1 19 3" xmodmap -e "pointer = 1 20 3" xmodmap -e "pointer = 1 21 3" xmodmap -e "pointer = 1 22 3" xmodmap -e "pointer = 1 23 3" xmodmap -e "pointer = 1 24 3" xmodmap -e "pointer = 1 25 3" Any clue ? I would like to avoid buying a new mouse just for a paste problem.

  Read the article

• Hard drive after PCB swap strange stuff

  - by ramyy

  I’ve done a PCB swap to my HDD. The HDD model is: WD6400AAKS-00A7B2. The original PCB PN matches the new one (first three letter groups), though the cache mismatches (16MB original, 8MB new). The Hardware store that made the swap told me it was hard to do the swap, they have done firmware adaptation. I can see that this firmware version does not match the original, (01.03B01 original, 05.04E05 new). Still I can see that the serial number and model of the drive is correct, the hard drive appeared normal in the BIOS, all the partitions show and everything appears normal. I have encountered three things though, I have left the drive non operated for 2-3 weeks after the swap to avoid corrupting the data or anything else the new PCB might cause, until I buy a new drive and backup the data. I got a drive, and when I powered the old drive manually (I have a laptop, I use a normal desktop power supply and a USB/SATA connector), I heard the motor start and I could hear ticking as if the motor’s somehow struggling to start, and then the motor sound starts again then the ticking, and so on.. I tried powering again it happened again. The third time it started normally and I could see everything normally. I took the chance and copied all the data over to the new drive. When I was done, I powered off the drive (after more than 25 hours of continuous operation), tried to power it up again and it did so normally, and so are the times I powered it up later; but I got very suspicious now. What could be the problem here? And what happened new, it used to power normally after the swap directly? The second thing that happened is that I found size differences with some files; some include movies, songs, (.iso) files for games, and programs. I could find the size is the same, but size on disk is a little more on the new drive for these files. . I’ve tried some of those files (with size differences) they worked fine. They are not too much but still make you suspicious of the integrity of the data copied; one cannot try if all files are working for about (580 GB) worth of data. I tried copying these files on the same partition they exist of the old drive; they are the same in size as when copied to the new drive (allocation unit size not the issue). I took an image of a partition (sector by sector including empty ones) and when I explore it, these file sizes are equal to the original (old drive); I copy them anywhere else their size on disk, increases, i.e becomes equal to the ones I copy from the old drive itself anywhere. Why the size difference and can one trust the integrity of the data?? The third thing is that when I connect my new external USB HDD, the partitions of the old HDD unmount and then mount again. Connected are: (USB mouse + Old HDD) then external HDD. Why that happens?? Considering the following: I compared the SMART reports from after the swap directly and after the copying, no error readings or reallocated sectors where reported. Here they are: http://www.image-share.com/ijpg-1939-219.html I later ran both WD data life guard tests and they came out passed. I’m worried for this drive since I must be sure the data is fine and safe on the new one, and I will consider it backup for the new one, since you can’t trust anything anymore. I hope you can forgive me for the length of the post, but couldn’t ignore any of the details, this hard drive contains very important data to me and I have to deal with the situation with great care.

  Read the article

• Lockdown users on Windows Server 2012

  - by el.severo

  I set up a Active Directory on a server machine with Windows Server 2012 and I'd like to create some users with limitations like Windows Steady State does in Windows XP (locally). Seen already the Windows SteadyState Handbook (with Windows Server 2008), but I'd like to know if anyone has tried this before, the limitations are the following: 1. Prevent locked or roaming user profiles that cannot be found on the computer from logging on 2. Do not cache copies of locked or roaming user profiles for users who have previously logged on to this computer 3. Do not allow Windows to compute and store passwords using LAN Manager Hash values 4. Do not store usernames or passwords used to log on to the Windows Live ID or the domain 5. Prevent users from creating folders and files on drive C:\ 6. Lock profile to prevent the user from making permanent changes 7. Remove the Control Panel, Printer and Network Settings from the Classic Start menu 8. Remove the Favorites icon 9. Remove the My Network Places icon 10. Remove the Frequently Used Program list 11. Remove the Shared documents folder from My Computer 12. Remove control Panel icon 13. Remove the Set Program Access and Defaults icon 14. Remove the Network Connection(Connect To)icon 15. Remove the Printers and Faxes icon 16. Remove the Run icon 17. Prevent access to Windows Explorer features: Folder Options, Customize Toolbar, and the Notification Area 18. Prevent access to the taskbar 19. Prevent access to the command prompt 20. Prevent access to the registry editor 21. Prevent access to the Task Manager 22. Prevent access to Microsoft Management Console utilities 23. Prevent users from adding or removing printers 24. Prevent users from locking the computer 25. Prevent password changes (also requires the Control Panel icon to be removed) 26. Disable System Tools and other management programs 27. Prevent users from saving files to the desktop 28. Hide A Drive 29. Hide B Drive 30. Hide C Drive 31. Prevent changes to Internet Explorer registry settings 32. Empty the Temporary Internet Files folder when Internet Explorer is closed 33. Remove Internet Options 34. Remove General tab in Internet Options 35. Remove Security tab in Internet Options 36. Remove Privacy tab in Internet Options 37. Remove Content tab in Internet Options 38. Remove Connections tab in Internet Options 39. Remove Programs tab in Internet Options 40. Remove Advanced tab in Internet Options 41. Set a home page (Internet Explorer) 42. Restrict the possibility to change desktop image 43. Restrict the possibility to change wallpaper 44. Restrict usb flash drives Any suggestions for this? UPDATE: As @Dan suggested me I'd like to specify that would be applied to a educational scenario where students can login from a computer and want to add some restrictions to them.

  Read the article

• Scripting Windows Shares - VBS

  - by Calvin Piche

  So i am totally new to VBS, never used it. I am trying to create multiple shares and i found a Microsoft VBS script that can do this(http://gallery.technet.microsoft.com/scriptcenter/6309d93b-fcc3-4586-b102-a71415244712) My question is, this script only allows for one domain group or user to be added for permissions where i am needing to add a couple with different permissions(got that figured out) Below is the script that i have modified for my needs but just need to add in the second group with the other permissions. If there is an easier way to do this please let me know. 'ShareSetup.vbs '========================================================================== Option Explicit Const FILE_SHARE = 0 Const MAXIMUM_CONNECTIONS = 25 Dim strComputer Dim objWMIService Dim objNewShare strComputer = "." Set objWMIService = GetObject("winmgmts:" & "{impersonationLevel=impersonate}!\\" & strComputer & "\root\cimv2") Set objNewShare = objWMIService.Get("Win32_Share") Call sharesec ("C:\Published Apps\Logs01", "Logs01", "Log01", "Support") Call sharesec2 ("C:\Published Apps\Logs01", "Logs01", "Log01", "Domain Admins") Sub sharesec(Fname,shr,info,account) 'Fname = Folder path, shr = Share name, info = Share Description, account = account or group you are assigning share permissions to Dim FSO Dim Services Dim SecDescClass Dim SecDesc Dim Trustee Dim ACE Dim Share Dim InParam Dim Network Dim FolderName Dim AdminServer Dim ShareName FolderName = Fname AdminServer = "\\" & strComputer ShareName = shr Set Services = GetObject("WINMGMTS:{impersonationLevel=impersonate,(Security)}!" & AdminServer & "\ROOT\CIMV2") Set SecDescClass = Services.Get("Win32_SecurityDescriptor") Set SecDesc = SecDescClass.SpawnInstance_() 'Set Trustee = Services.Get("Win32_Trustee").SpawnInstance_ 'Trustee.Domain = Null 'Trustee.Name = "EVERYONE" 'Trustee.Properties_.Item("SID") = Array(1, 1, 0, 0, 0, 0, 0, 1, 0, 0, 0, 0) Set Trustee = SetGroupTrustee("domain", account) 'Replace ACME with your domain name. 'To assign permissions to individual accounts use SetAccountTrustee rather than SetGroupTrustee Set ACE = Services.Get("Win32_Ace").SpawnInstance_ ACE.Properties_.Item("AccessMask") = 1179817 ACE.Properties_.Item("AceFlags") = 3 ACE.Properties_.Item("AceType") = 0 ACE.Properties_.Item("Trustee") = Trustee SecDesc.Properties_.Item("DACL") = Array(ACE) Set Share = Services.Get("Win32_Share") Set InParam = Share.Methods_("Create").InParameters.SpawnInstance_() InParam.Properties_.Item("Access") = SecDesc InParam.Properties_.Item("Description") = "Public Share" InParam.Properties_.Item("Name") = ShareName InParam.Properties_.Item("Path") = FolderName InParam.Properties_.Item("Type") = 0 Share.ExecMethod_ "Create", InParam End Sub Sub sharesec2(Fname,shr,info,account) 'Fname = Folder path, shr = Share name, info = Share Description, account = account or group you are assigning share permissions to Dim FSO Dim Services Dim SecDescClass Dim SecDesc Dim Trustee Dim ACE2 Dim Share Dim InParam Dim Network Dim FolderName Dim AdminServer Dim ShareName FolderName = Fname AdminServer = "\\" & strComputer ShareName = shr Set Services = GetObject("WINMGMTS:{impersonationLevel=impersonate,(Security)}!" & AdminServer & "\ROOT\CIMV2") Set SecDescClass = Services.Get("Win32_SecurityDescriptor") Set SecDesc = SecDescClass.SpawnInstance_() 'Set Trustee = Services.Get("Win32_Trustee").SpawnInstance_ 'Trustee.Domain = Null 'Trustee.Name = "EVERYONE" 'Trustee.Properties_.Item("SID") = Array(1, 1, 0, 0, 0, 0, 0, 1, 0, 0, 0, 0) Set Trustee = SetGroupTrustee("domain", account) 'Replace ACME with your domain name. 'To assign permissions to individual accounts use SetAccountTrustee rather than SetGroupTrustee Set ACE2 = Services.Get("Win32_Ace").SpawnInstance_ ACE2.Properties_.Item("AccessMask") = 1179817 ACE2.Properties_.Item("AceFlags") = 3 ACE2.Properties_.Item("AceType") = 0 ACE2.Properties_.Item("Trustee") = Trustee SecDesc.Properties_.Item("DACL") = Array(ACE2) End Sub Function SetAccountTrustee(strDomain, strName) set objTrustee = getObject("Winmgmts: {impersonationlevel=impersonate}!root/cimv2:Win32_Trustee").Spawninstance_ set account = getObject("Winmgmts: {impersonationlevel=impersonate}!root/cimv2:Win32_Account.Name='" & strName & "',Domain='" & strDomain &"'") set accountSID = getObject("Winmgmts: {impersonationlevel=impersonate}!root/cimv2:Win32_SID.SID='" & account.SID &"'") objTrustee.Domain = strDomain objTrustee.Name = strName objTrustee.Properties_.item("SID") = accountSID.BinaryRepresentation set accountSID = nothing set account = nothing set SetAccountTrustee = objTrustee End Function Function SetGroupTrustee(strDomain, strName) Dim objTrustee Dim account Dim accountSID set objTrustee = getObject("Winmgmts: {impersonationlevel=impersonate}!root/cimv2:Win32_Trustee").Spawninstance_ set account = getObject("Winmgmts:{impersonationlevel=impersonate}!root/cimv2:Win32_Group.Name='" & strName & "',Domain='" & strDomain &"'") set accountSID = getObject("Winmgmts: {impersonationlevel=impersonate}!root/cimv2:Win32_SID.SID='" & account.SID &"'") objTrustee.Domain = strDomain objTrustee.Name = strName objTrustee.Properties_.item("SID") = accountSID.BinaryRepresentation set accountSID = nothing set account = nothing set SetGroupTrustee = objTrustee End Function

  Read the article

• unmet dependencies in Ubuntu 12.04

  - by lee.O

  I tried today to install a dvb-card on my Ubuntu 12.04 (Linux blauhai-linux 3.2.0-25-generic #40-Ubuntu SMP Wed May 23 20:30:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux ). The installation failed with an error. After that, i tried to install python (it was already installed but i got this error): linux:~$ sudo apt-get install git Reading package lists... Done Building dependency tree Reading state information... Done git is already the newest version. You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: python-glade2:i386 : Depends: python:i386 (< 2.5) but it is not going to be installed Depends: python-support:i386 (= 0.3.4) but it is not installable Depends: python:i386 (= 2.4) but it is not going to be installed Depends: libglade2-0:i386 (= 1:2.5.1) but it is not going to be installed Depends: python-gtk2:i386 (= 2.8.6-8) but it is not going to be installed python-numeric:i386 : Depends: python:i386 (< 2.5) but it is not going to be installed Depends: python:i386 (= 2.3) but it is not going to be installed Depends: python-central:i386 (= 0.5.7) but it is not installable E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). well, i can read and tried the proposed command, but then i get this: linux:~$ sudo apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages were automatically installed and are no longer required: libopenal1:i386 libsdl-ttf2.0-0:i386 libkrb5-3:i386 libgconf-2-4:i386 libsm-dev libatk1.0-0:i386 libk5crypto3:i386 libstdc++5:i386 libqt4-declarative:i386 libxcomposite1:i386 libice-dev libgail18:i386 libldap-2.4-2:i386 libao-common libv4l-0:i386 liblcms1:i386 libqt4-qt3support:i386 libroken18-heimdal:i386 libunistring0:i386 libcupsimage2:i386 libgphoto2-port0:i386 libidn11:i386 libnss3:i386 libcaca0:i386 gtk2-engines:i386 libgudev-1.0-0:i386 libjpeg-turbo8:i386 libpthread-stubs0 libcairo-gobject2:i386 libavc1394-0:i386 libjpeg8:i386 libotr2 libaio1:i386 libsane:i386 odbcinst1debian2 odbcinst1debian2:i386 libqt4-test:i386 libqt4-script:i386 libqt4-designer:i386 libsdl-mixer1.2:i386 libqt4-network:i386 libqt4-dbus:i386 libcap2:i386 libproxy1:i386 ibus-gtk:i386 libdbus-glib-1-2:i386 libtdb1:i386 libasn1-8-heimdal:i386 libspeex1:i386 libxslt1.1:i386 libgomp1:i386 libcapi20-3:i386 libibus-1.0-0:i386 libcairo2:i386 libgnutls26:i386 libopenal-data odbcinst libgssapi3-heimdal:i386 libcanberra0:i386 libtasn1-3:i386 libfreetype6:i386 x11proto-kb-dev gtk2-engines-murrine:i386 libwavpack1:i386 libqt4-opengl:i386 libsoup-gnome2.4-1:i386 libv4lconvert0:i386 gstreamer0.10-plugins-good:i386 libc6-i386 lib32gcc1 libqt4-xmlpatterns:i386 librsvg2-common:i386 libdatrie1:i386 xtrans-dev libavahi-common-data:i386 libiec61883-0:i386 lib32asound2 libgdk-pixbuf2.0-0:i386 libsdl-image1.2:i386 libp11-kit0:i386 x11proto-input-dev libwind0-heimdal:i386 libpixman-1-0:i386 libsdl1.2debian:i386 libxaw7:i386 libgdbm3:i386 libcups2:i386 libcurl3:i386 libqtcore4:i386 libxinerama1:i386 libesd0:i386 libmikmod2:i386 libkrb5support0:i386 libxft2:i386 libxt-dev libcroco3:i386 libpulse-mainloop-glib0:i386 libice6:i386 libaa1:i386 libieee1284-3:i386 libgcrypt11:i386 libthai0:i386 libao4:i386 libkeyutils1:i386 libxmu6:i386 libcanberra-gtk0:i386 libvorbisfile3:i386 libqt4-sql:i386 esound-common libxpm4:i386 libqt4-svg:i386 libusb-0.1-4:i386 libgail-common:i386 libxrender1:i386 libhcrypto4-heimdal:i386 libraw1394-11:i386 libnspr4:i386 libshout3:i386 libdv4:i386 libhx509-5-heimdal:i386 libxau-dev libqt4-xml:i386 gstreamer0.10-x:i386 libgettextpo0:i386 libxss1:i386 libgd2-xpm:i386 libheimbase1-heimdal:i386 libtiff4:i386 libsdl-net1.2:i386 libjasper1:i386 libgnome-keyring0:i386 libxtst6:i386 gtk2-engines-pixbuf:i386 libqtgui4:i386 libtag1c2a:i386 librsvg2-2:i386 libavahi-client3:i386 libssl0.9.8:i386 libmpg123-0:i386 libmad0:i386 libsasl2-2:i386 xorg-sgml-doctools libgsoap1 gtk2-engines-oxygen:i386 libfontconfig1:i386 xaw3dg:i386 libpango1.0-0:i386 libsm6:i386 libx11-dev libheimntlm0-heimdal:i386 libpulsedsp:i386 lib32stdc++6 libx11-doc libqt4-sql-mysql:i386 libxcb-render0:i386 libodbc1:i386 libexif12:i386 libqt4-scripttools:i386 librtmp0:i386 libgssapi-krb5-2:i386 libxi6:i386 libqtwebkit4:i386 libxcb1-dev libxp6:i386 libaudio2:i386 libxcursor1:i386 libxcb-shm0:i386 libxt6:i386 libxv1:i386 libsasl2-modules:i386 libavahi-common3:i386 libxrandr2:i386 x11proto-core-dev libsqlite3-0:i386 libmng1:i386 libgtk2.0-0:i386 libxdmcp-dev libpthread-stubs0-dev libltdl7:i386 libkrb5-26-heimdal:i386 libssl1.0.0:i386 glib-networking:i386 libgpg-error0:i386 libsoup2.4-1:i386 libgphoto2-2:i386 libtag1-vanilla:i386 libaudiofile1:i386 libglade2-0:i386 Use 'apt-get autoremove' to remove them. The following extra packages will be installed: default-jre default-jre-headless icedtea-6-jre-cacao icedtea-6-jre-jamvm icedtea-netx icedtea-netx-common libglade2-0:i386 libpython3.2 openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib python3 python3-minimal python3-uno python3.2 python3.2-minimal Suggested packages: icedtea-plugin sun-java6-fonts fonts-ipafont-gothic fonts-ipafont-mincho ttf-telugu-fonts ttf-oriya-fonts ttf-kannada-fonts ttf-bengali-fonts python3-doc python3-tk python3.2-doc binfmt-support The following packages will be REMOVED: activity-log-manager-control-center aisleriot alacarte apparmor apport apport-gtk apt-xapian-index aptdaemon apturl apturl-common bluez bluez-alsa bluez-alsa:i386 bluez-gstreamer checkbox checkbox-qt command-not-found compiz compiz-gnome compiz-plugins-main-default compizconfig-backend-gconf deja-dup duplicity eog evolution-data-server firefox firefox-globalmenu firefox-gnome-support foomatic-db-compressed-ppds gconf-editor gconf2 gdb gedit gir1.2-mutter-3.0 gir1.2-peas-1.0 gir1.2-rb-3.0 gir1.2-totem-1.0 gir1.2-ubuntuoneui-3.0 gksu gnome-applets gnome-applets-data gnome-bluetooth gnome-contacts gnome-control-center gnome-media gnome-menus gnome-orca gnome-panel gnome-panel-data gnome-session-fallback gnome-shell gnome-sudoku gnome-terminal gnome-terminal-data gnome-themes-standard gnome-tweak-tool gnome-user-share gstreamer0.10-gconf gwibber gwibber-service gwibber-service-facebook gwibber-service-identica gwibber-service-twitter hplip hplip-data ia32-libs ia32-libs-multiarch:i386 ibus ibus-pinyin ibus-table indicator-datetime indicator-power jockey-common jockey-gtk landscape-client-ui-install language-selector-common language-selector-gnome launchpad-integration libcanberra-gtk-module libcanberra-gtk-module:i386 libcanberra-gtk3-module libcompizconfig0 libfolks-eds25 libgksu2-0 libgnome-media-profiles-3.0-0 libgnome2-0 libgnome2-common libgnomevfs2-0 libgnomevfs2-common libgweather-3-0 libgweather-common libgwibber-gtk2 libgwibber2 libmetacity-private0 libmutter0 libpeas-1.0-0 libpurple-bin libpython2.7 libreoffice-gnome librhythmbox-core5 libsyncdaemon-1.0-1 libtotem0 libubuntuoneui-3.0-1 light-themes lsb-release metacity metacity-common mutter-common nautilus-dropbox nautilus-share network-manager-gnome nvidia-common nvidia-settings nvidia-settings-updates onboard oneconf openjdk-7-jdk openjdk-7-jre openprinting-ppds pidgin pidgin-libnotify pidgin-otr printer-driver-foo2zjs printer-driver-ptouch printer-driver-pxljr printer-driver-sag-gdi printer-driver-splix python python-appindicator python-apport python-apt python-apt-common python-aptdaemon python-aptdaemon.gtk3widgets python-aptdaemon.pkcompat python-brlapi python-cairo python-central python-chardet python-configglue python-crypto python-cups python-cupshelpers python-dateutil python-dbus python-debian python-debtagshw python-defer python-dirspec python-egenix-mxdatetime python-egenix-mxtools python-gconf python-gdbm python-gi python-gi-cairo python-glade2:i386 python-gmenu python-gnomekeyring python-gnupginterface python-gobject python-gobject-2 python-gpgme python-gst0.10 python-gtk2 python-httplib2 python-ibus python-imaging python-keyring python-launchpadlib python-lazr.restfulclient python-lazr.uri python-libproxy python-libxml2 python-louis python-mako python-markupsafe python-minimal python-notify python-numeric:i386 python-oauth python-openssl python-packagekit python-pam python-pexpect python-piston-mini-client python-pkg-resources python-problem-report python-protobuf python-pyatspi2 python-pycurl python-pyinotify python-renderpm python-reportlab python-reportlab-accel python-serial python-simplejson python-smbc python-software-properties python-speechd python-twisted-bin python-twisted-core python-twisted-names python-twisted-web python-ubuntu-sso-client python-ubuntuone-client python-ubuntuone-control-panel python-ubuntuone-storageprotocol python-uno python-virtkey python-wadllib python-xapian python-xdg python-xkit python-zeitgeist python-zope.interface python2.7 python2.7-minimal rhythmbox rhythmbox-mozilla rhythmbox-plugin-cdrecorder rhythmbox-plugin-magnatune rhythmbox-plugin-zeitgeist rhythmbox-plugins rhythmbox-ubuntuone screen-resolution-extra sessioninstaller skype software-center software-center-aptdaemon-plugins software-properties-common software-properties-gtk system-config-printer-common system-config-printer-gnome system-config-printer-udev texlive-extra-utils totem totem-mozilla totem-plugins ubuntu-artwork ubuntu-desktop ubuntu-minimal ubuntu-sso-client ubuntu-sso-client-gtk ubuntu-standard ubuntu-system-service ubuntuone-client ubuntuone-client-gnome ubuntuone-control-panel ubuntuone-couch ubuntuone-installer ufw unattended-upgrades unity unity-2d unity-common unity-lens-applications unity-lens-video unity-scope-musicstores unity-scope-video-remote update-manager update-manager-core update-notifier update-notifier-common usb-creator-common usb-creator-gtk virtualbox virtualbox-dkms virtualbox-qt xdiagnose xul-ext-ubufox zeitgeist zeitgeist-core zeitgeist-datahub The following NEW packages will be installed: default-jre default-jre-headless icedtea-6-jre-cacao icedtea-6-jre-jamvm icedtea-netx icedtea-netx-common libglade2-0:i386 libpython3.2 openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib python3 python3-minimal python3-uno python3.2 python3.2-minimal WARNING: The following essential packages will be removed. This should NOT be done unless you know exactly what you are doing! python-minimal python2.7-minimal (due to python-minimal) 0 upgraded, 16 newly installed, 273 to remove and 0 not upgraded. 2 not fully installed or removed. Need to get 39.1 MB of archives. After this operation, 324 MB disk space will be freed. You are about to do something potentially harmful. To continue type in the phrase 'Yes, do as I say!' ?] Thats not good, is it?! Should i run this command or should i run another command to fix this problem? Would be great if somebody can help me. :) Thanks in advance. best regards

  Read the article

• Week in Geek: USDA Chooses Microsoft for Cloud Services Edition

  - by Asian Angel

  This week we learned how to create geeky LED holiday lights with old bottles, dig deeper in Windows Defrag via the command prompt, use Google Chrome’s drag/drop feature to upload files easier, find great gift recommendations by looking through the How-To Geek holiday gift guide, and have fun adding Merry Christmas fonts to our computers. Photo by ntr23. Random Geek Links It has been a busy week, so we have extra news link goodness with information that is good for you to know. USDA making the move to Microsoft The U.S. Department of Agriculture has announced that it has chosen Microsoft to host things like e-mail, instant messaging, and collaboration through the software giant’s Business Productivity Online Suite. Google says it was cut off from USDA project bid Google is claiming that it was not given a chance to bid on a cloud-computing project for the U.S. Department of Agriculture, for which the contract was awarded to rival Microsoft. Apache is being forced into a Java Fork When Oracle rolled over Apache and Google’s objections to its Java plans in December, the scene was set for Apache to leave and, eventually, force a Java code fork. Tumblr explains daylong outage After experiencing an outage that started on Sunday afternoon and stretched through most of the day yesterday, Tumblr has explained what happened. Google demos Chrome OS, launches pilot program During a press briefing this week in San Francisco, Google launched the Chrome application store and demonstrated Chrome OS, its browser-centric netbook operating system. Don’t expect Spotify in U.S. this holiday season As of last week, Spotify had yet to sign a single licensing deal with a major label, after spending more than a year negotiating, multiple music sources told CNET. December 2010 Patch Tuesday will come with most bulletins ever According to the Microsoft Security Response Center, Microsoft will issue 17 Security Bulletins addressing 40 vulnerabilities on Tuesday, December 14. It will also host a webcast to address customer questions the following day. Hacker plants back door in Symbian firmware Indian hacker Atul Alex has had a look at the firmware for Symbian S60 smartphones and come up with a back door for it. PC quarantines raise tough complexities The concept of quarantining PCs to prevent widespread infection is “interesting, but difficult to implement, with far too many problems”, said security experts. Symantec: DDoS attacks hard to defend It has surfaced that the distributed denial of service (DDoS) attacks on Visa and MasterCard Web sites on Wednesday were carried out by a toolkit known as low orbit ion cannon (LOIC). Web Sockets and the risks of unfinished standards Enthusiasm for a promising new standard called Web Sockets has quickly cooled in some quarters as a potential security problem led some browser makers to hastily postpone support. Internet Explorer 9 to get tracking protection Microsoft is making changes to Internet Explorer 9’s security features that will better enable users to keep sites from tracking their activity across browsing sessions. NASA sold PCs with sensitive data NASA failed to remove sensitive data from computers that it sold, according to an audit report released this week. Cybercrooks create fake Amazon receipts The bad guys have created yet another online scam, this one involving fake Amazon receipts. World of Warcraft character move fees waived Until December 22, Blizzard will allow free realm transfers from 25 highly populated servers to alleviate log-in queues or performance issues. (The free transfers are one-way and one-time only.) SpaceX Dragon reaches orbit atop a Falcon with a fiery tail The Space Exploration Technologies corporation has become the first nongovernmental entity to put a vehicle into low Earth orbit. Geek Video of the Week If birds have wings, then why are the Angry Birds using slingshots? Photo by Dorkly Bits. Wait… Birds have Wings, Why are the Angry Ones Using Slingshots? Sysadmin Geek Tips How To Setup Email Alerts on Linux Using Gmail or SMTP Linux machines may require administrative intervention in countless ways, but without manually logging into them how would you know about it? Here’s how to setup emails to get notified when your machines want some tender love and attention. Random TinyHacker Links Red Panda Webcam Support Firefox and the Knoxville Zoo’s Red Panda program. Christmas Icons (Icons we like) Superb set of holiday icons by lgp85 at deviantArt. Download the .zip and use as .png or convert to .ico at Convertico.com or with tiny app Imagicon. Super User Questions Enjoy reading the great answers to this week’s popular questions from Super User Useful USB boot disks? DVD/CD burning .zip: is it more reliable, faster, longer lasting to burn a zip of files rather than the files as a folder? What are other ways to backup my files if I do not have an external drive? Anti virus what is the difference between these all? How can I block all Facebook elements/content? How-To Geek Weekly Article Recap Have you had a busy week between work and preparing for the holidays? Get caught up on your HTG reading with our hottest articles of the week. 20 Windows Keyboard Shortcuts You Might Not Know The 50 Best Registry Hacks that Make Windows Better LCD? LED? Plasma? The How-To Geek Guide to HDTV Technology HTG Explains: Which Linux File System Should You Choose? How to Use and Customize Google Chrome Web Apps One Year Ago on How-To Geek This week’s batch of retro geeky goodness is all about customizing Windows 7. ClassicShell Adds Classic Start Menu and Explorer Features to Windows 7 Get an Aero-Styled Classic Start Menu in Windows 7 Customize the Windows 7 Logon Screen Get the Classic Style Network Activity Indicator Back in Windows 7 How To Enable Check Boxes for Items In Windows 7 The Geek Note We would like you to join us in welcoming Jason Fitzpatrick to the writing staff here at How-To Geek. He started with us this past week, so take some time to read through his articles about the Wii, Kindle, & PlayStation 2 Peripherals and leave a friendly comment to say “Hi”! Got a great tip to share? Make sure to send it in to us at [email protected]. Photo by real00. Latest Features How-To Geek ETC The 50 Best Registry Hacks that Make Windows Better The How-To Geek Holiday Gift Guide (Geeky Stuff We Like) LCD? LED? Plasma? The How-To Geek Guide to HDTV Technology The How-To Geek Guide to Learning Photoshop, Part 8: Filters Improve Digital Photography by Calibrating Your Monitor Our Favorite Tech: What We’re Thankful For at How-To Geek Settle into Orbit with the Voyage Theme for Chrome and Iron Awesome Safari Compass Icons Set Escape from the Exploding Planet Wallpaper Move Your Tumblr Blog to WordPress Pytask is an Easy to Use To-Do List Manager for Your Ubuntu System Snowy Christmas House Personas Theme for Firefox

  Read the article

< Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >