Search Results

Search found 39497 results on 1580 pages for 'two shoes'.

Page 187/1580 | < Previous Page | 183 184 185 186 187 188 189 190 191 192 193 194  | Next Page >

• MacGyver Moments

  - by Geoff N. Hiten

  Denny Cherry tagged me to write about my best MacGyver Moment.  Usually I ignore blogosphere fluff and just use this space to write what I think is important.  However, #MVP10 just ended and I have a stronger sense of community.  Besides, where else would I mention my second best Macgyver moment was making a BIOS jumper out of a soda can.  Aluminum is conductive and I didn't have any real jumpers lying around. My best moment is probably my entire home computer network.  Every system but one is hand-built, usually cobbled together out of spare parts and 'adapted' from its original purpose. My Primary Domain Controller is a Dell 2300.   The Service Tag indicates it was shipped to the original owner in 1999.  Box has a PERC/1 RAID controller.  I acquired this from a previous employer for $50.  It runs Windows Server 2003 Enterprise Edition.  Does DNS, DHCP, and RADIUS services as a bonus.  RADIUS authentication is used for VPN and Wireless access.  It is nice to sign in once and be done with it. The Secondary Domain Controller is an old desktop.  Dual P-III 933 with some extra drives. My VPN box is a P-II 250 with 384MB of RAM and a 21 GB hard drive.  I did a P-to-V to my Hyper-V box a year or so ago and retired the hardware again.  Dynamic DNS lets me connect no matter how often Comcast shuffles my IP. The Hyper-V box is a desktop system with 8GB RAM and an AMD Athlon 5000+ processor.  Cost me less than $500 to put together nearly two years ago.  I reasoned that if Vista and Windows 2008 were the same code then Vista 64-bit certified meant the drivers for Vista would load into Windows 2008.  Turns out I was right. Later I added three 1TB drives but wasn't too happy with how that turned out.  I recovered two of the drives yesterday and am building an iSCSI storage unit. (Much thanks to Starwind.  Great product).  I am using an old AMD 1.1GhZ box with 1.5 GB RAM (cobbled together from three old PCs) as my storave server.  The Hyper-V box is slated for an OS rebuild to 2008 R2 once I get the storage system worked out.  maybe in a week or two. A couple of DLink Gigabit switches ties everything together. Add in the Vonage box, the three PCs, the Wireless-N Access Point, the two notebooks and the XBox and you have gone from MacGyver to darn near Rube Goldberg. The only thing I really spend money on is power supplies and fans.  I buy top-of-the-line for both. I even pull and crimp my own cables. Oh, and if my kids hose up a PC, I have all of their data on a server elsewhere.  Every PC and laptop is pretty much interchangable for email and basic workstation tasks.  That helps a lot too. Of course I will tag SQLVariant.

  Read the article

• Oracle OpenWorld Update: Oracle GoldenGate Customer Panels

  - by Doug Reid

  0 false 18 pt 18 pt 0 0 false false false /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:12.0pt; font-family:"Times New Roman"; mso-ascii-font-family:Cambria; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Cambria; mso-hansi-theme-font:minor-latin;} We are two weeks out from the start of Oracle OpenWorld 2012. The Data Integration team has a solid line-up of product and customer sessions for you to attend this year, plus five hands-on labs, and numerous demonstration pods in Moscone South. On Monday we kick the track off with Brad Adelberg’s Future Strategy, Direction and Roadmap for Oracle’s Data Integration Platform at 10:45AM in Moscone West 3005. Over the rest of the week we have a number of deep dive sessions that build out the themes that Brad discusses in his keynote, but the two that I would like to highlight today are our Oracle GoldenGate customer panels. The first customer panel is on Zero Downtime Operations and is on Monday at 1:45 in Moscone West 3005. The theme of this session is how to reduce downtime for critical must-succeed systems. Here’s a rundown of the session: Bank of America, TALX, and St. Jude Medical all have users communities that expect systems to be available around the clock. In this customer panel session, Bank of America discusses how it will be leveraging Oracle GoldenGate. St. Jude Medical shares how it is using Oracle GoldenGate to achieve a zero-downtime migration for a 5 TB Oracle online transaction processing (OLTP) 24/7 mission-critical database. TALX discusses how Equifax Workforce Information Services used Oracle GoldenGate to move from processing online transactions in a single site to processing concurrently from two geographically disparate data centers, providing a highly available solution with significant burst capacity. On Tuesday at 11:45 in Moscone West 3005 we switch gears and host a customer panel on Operational Reporting. The theme of this customer panel is all around reporting and how Oracle GoldenGate raises the bar on reporting by enabling real-time access to real-time data. Here’s a rundown of the session: Turk Telekom and Comcast are half a world away from each other, but these two powerhouse companies have both drastically improved performance and access to real-time data by using Oracle GoldenGate. During this panel discussion, Turk Telekom will explain its evaluation and implementation of Oracle GoldenGate, how the business has experienced significant improvements in the core database and reporting platform, and how it plans to expand its usage into its SOA architecture and its architecture based on Oracle’s Siebel platform. Comcast will explain its implementation of Oracle GoldenGate and how it moves data in real time from its mission-critical HP NonStop database to a Teradata data warehouse. Join us at our sessions to learn what other customers are doing with our products or stop by our demo pods in Moscone south and meet the product management and development teams.

  Read the article

• Enjoy How-To Geek User Style Script Goodness

  - by Asian Angel

  Most people may not be aware of it but there are two user style scripts that have been created just for use with the How-To Geek website. If you are curious then join us as we look at these two scripts at work. Note: User Style Scripts & User Scripts can be added to most browsers but we are using Firefox for our examples here. The How-to Geek Wide User Style Script The first of the two scripts affects the viewing width of the website’s news content. Here you can see everything set at the normal width. When you visit the UserStyles website you will be able to view basic information about the script and see the code itself if desired. On the right side of the page is the good part though. Since we are using Firefox with Greasemonkey installed we chose the the “install as a user script option”. Notice that the script is available for other browsers as well (very nice!) Within a few moments of clicking on the “install as a user script button” you will see the following window asking confirmation for installing the script. After installing the user style script and refreshing the page it has now stretched out to fill 90% of the browser window’s area. Definitely nice! The How-To Geek – News and Comments (600px) User Style Script The second script can be very useful for anyone with the limited screen real-estate of a netbook. You can see another of the articles from here at the site viewed in a  “normal mode”. Once again you can view basic information about this particular user style script and view the code if desired. As above we have the Firefox/Greasemonkey combination at work so we installed as a user script. This is one of the great things about using Greasemonkey…it always checks with you to make certain that no unauthorized scripts are added. Once the script was installed and we refreshed the page things looked very very different. All the focus has been placed on the article itself and any comments attached to the article. For those who may be curious this is what the homepage looks like using this script. Conclusion If you have been wanting to add a little bit of “viewing spice” to your browser for the How-To Geek website then definitely pop over to the User Styles website and give these two scripts a try. Using Opera Browser? See our how-to for adding user scripts to Opera here. Links Install the How-to Geek Wide User Style Script Install the How-To Geek – News and Comments (600px) User Style Script Download the Greasemonkey extension for Firefox (Mozilla Add-ons) Download the Stylish extension for Firefox (Mozilla Add-ons) Similar Articles Productive Geek Tips Set Up User Scripts in Opera BrowserSet Gmail as Default Mail Client in UbuntuHide Flash Animations in Google ChromeShell Script to Upload a File to the Same Subdirectory on a Remote ServerAutomate Adding Bookmarks to del.icio.us TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Quickly Schedule Meetings With NeedtoMeet Share Flickr Photos On Facebook Automatically Are You Blocked On Gtalk? Find out Discover Latest Android Apps On AppBrain The Ultimate Guide For YouTube Lovers Will it Blend? iPad Edition

  Read the article

• Bug in Delphi XE RegularExpressions Unit

  - by Jan Goyvaerts

  Using the new RegularExpressions unit in Delphi XE, you can iterate over all the matches that a regex finds in a string like this: procedure TForm1.Button1Click(Sender: TObject); var RegEx: TRegEx; Match: TMatch; begin RegEx := TRegex.Create('\w+'); Match := RegEx.Match('One two three four'); while Match.Success do begin Memo1.Lines.Add(Match.Value); Match := Match.NextMatch; end end; Or you could save yourself two lines of code by using the static TRegEx.Match call: procedure TForm1.Button2Click(Sender: TObject); var Match: TMatch; begin Match := TRegEx.Match('One two three four', '\w+'); while Match.Success do begin Memo1.Lines.Add(Match.Value); Match := Match.NextMatch; end end; Unfortunately, due to a bug in the RegularExpressions unit, the static call doesn’t work. Depending on your exact code, you may get fewer matches or blank matches than you should, or your application may crash with an access violation. The RegularExpressions unit defines TRegEx and TMatch as records. That way you don’t have to explicitly create and destroy them. Internally, TRegEx uses TPerlRegEx to do the heavy lifting. TPerlRegEx is a class that needs to be created and destroyed like any other class. If you look at the TRegEx source code, you’ll notice that it uses an interface to destroy the TPerlRegEx instance when TRegEx goes out of scope. Interfaces are reference counted in Delphi, making them usable for automatic memory management. The bug is that TMatch and TGroupCollection also need the TPerlRegEx instance to do their work. TRegEx passes its TPerlRegEx instance to TMatch and TGroupCollection, but it does not pass the instance of the interface that is responsible for destroying TPerlRegEx. This is not a problem in our first code sample. TRegEx stays in scope until we’re done with TMatch. The interface is destroyed when Button1Click exits. In the second code sample, the static TRegEx.Match call creates a local variable of type TRegEx. This local variable goes out of scope when TRegEx.Match returns. Thus the reference count on the interface reaches zero and TPerlRegEx is destroyed when TRegEx.Match returns. When we call MatchAgain the TMatch record tries to use a TPerlRegEx instance that has already been destroyed. To fix this bug, delete or rename the two RegularExpressions.dcu files and copy RegularExpressions.pas into your source code folder. Make these changes to both the TMatch and TGroupCollection records in this unit: Declare FNotifier: IInterface; in the private section. Add the parameter ANotifier: IInterface; to the Create constructor. Assign FNotifier := ANotifier; in the constructor’s implementation. You also need to add the ANotifier: IInterface; parameter to the TMatchCollection.Create constructor. Now try to compile some code that uses the RegularExpressions unit. The compiler will flag all calls to TMatch.Create, TGroupCollection.Create and TMatchCollection.Create. Fix them by adding the ANotifier or FNotifier parameter, depending on whether ARegEx or FRegEx is being passed. With these fixes, the TPerlRegEx instance won’t be destroyed until the last TRegEx, TMatch, or TGroupCollection that uses it goes out of scope or is used with a different regular expression.

  Read the article

• how to assign javascript variable value to the google analytics script? [migrated]

  - by Vinoth Prakash

  I have assigned two values in the two hidden variables at server Side and accessed those values at client side using script. I have written the google analytics code. I have set two custom variable. I need to pass two values which is stored in the javascript variables to the "value" of custom variable. I have assigned the varibales but values not displaying. please telll what error i made in the script. My aspx code <html xmlns="http://www.w3.org/1999/xhtml" > <head runat="server"> <title></title> </head> <body> <form id="form1" runat="server"> <div> <br /> Total Pirce&nbsp; &nbsp;: <asp:Label ID="Label1" runat="server" Text="10"></asp:Label><br /> &nbsp;Ship Price&nbsp; &nbsp; : <asp:Label ID="Label2" runat="server" Text="5"></asp:Label> <br /> ------------------<br /> Grand Total : <asp:Label ID="Label3" runat="server" Text="15"></asp:Label><br /> ------------------</div> <asp:HiddenField ID="HiddenField1" runat="server" /> <asp:HiddenField ID="HiddenField2" runat="server" /> </form> <script type="text/javascript"> var serverhid1 = document.getElementById('HiddenField1').value; var serverhid2 = document.getElementById('HiddenField2').value; alert(serverhid1) alert(serverhid2) var _gaq = _gaq || []; _gaq.push(['_setAccount', 'UA-35156990-1']); //Set Custom Variable _gaq.push(['_setCustomVar', 1, 'TotalPirce', serverhid1 , 3]); _gaq.push(['_setCustomVar', 2, 'Shipping','yes', 3]); _gaq.push(['_setCustomVar', 3, 'GrandTotal',check(), 3]); _gaq.push(['_setDomainName', 'none']); _gaq.push(['_trackPageview']); (function() { var ga = document.createElement('script'); ga.type = 'text/javascript'; ga.async = true; ga.src = ('https:' == document.location.protocol ? 'https://ssl' : 'http://www') + '.google-analytics.com/ga.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(ga, s); })(); </script> </body> </html> cs Code protected void Page_Load(object sender, EventArgs e) { HiddenField1.Value = Label1.Text; HiddenField2.Value = Label2.Text; }

  Read the article

• PARTNER WEBCAST- ORACLE COMPETENCE - PROGRAM (COMPETENCE VIRTUAL)

  - by mseika

  I am pleased to invite you to join the second (Competence Virtual). In Competence - program we will present Oracle Applications' Product's new functions and features including sales positioning. The key objectives of these webcasts are to inspire System Integrator's implementation personnel to conduct successful after sales in their Customer projects. Competencewill be presented on 1st Monday of each quarter after the billable day (4:00 to 5:00 PM CET). The webcast is intended for System Integrator's Implementation Certified Specialists but Competence is open for other interested Oracle Applications system Integrator's personnel as well. At first, two Oracle representatives will discuss Oracle's contribution to Partners. Then you will see product breakout session followed by Q&A with Oracle Experts. Each session will last for maximum 1 hour. A Q&A Document covering all questions and answers will be made available two weeks after the webcast. What are the Benefits for Partners? Find out how Competence helps you to improve your after sales Discover new functions and features so you can enrich your Customer’s solution Learn more about Oracle Applications products, especially sales positioning Hear crucial questions raised by colleagues alike, learn from their interest Engage and present your questions to subject experts Be inspired of the richness of Oracle Applications portfolio – for your and your Customer’s benefit.   Note: Should you already be familiar with a specific Product, then choose another one. Doing so you would expand your knowledge of the overall Applications portfolio. Some presentations contain product demonstration, although these presentations are not intended to be extremely detailed technical presentations. Product breakout sessions:- Fusion CRM: Effective, Efficient and Easy- Fusion HCM: Talent management overview performance, goals, talent review- Distributed Order Management - Fusion SCM Solution- Oracle Transportation Management- Oracle Value Chain Planning: Demantra Sales & Operation Planning and Demantra Demand Management- Oracle CX (Customer Experience) - formerly CEM: Powering Great Customer Experiences- EPM 11.1.2.2 Overview- Oracle Hyperion Profitability and Cost Management, 11.1.2.1 For more details please visit and other breakout sessions on OPN page. Delivery FormatCompetence- program (Competence Virtual) is a series of FREE prerecorded Applications product presentations followed by Q&A. It will be delivered over the Web. Participants have the opportunity to submit questions during the cast via chat and subject matter experts will provide verbal answers live. Competence consists of several parallel prerecorded product breakout sessions, each lasting for max. 1 hour. At first, two Oracle representatives will discuss Oracle’s contribution to Partners. Then you’ll see the product breakout sessions followed by Q&A with Oracle Experts. A Q&A document covering all questions and answers will be made available two weeks after the webcast. You can also see Competence afterwards as its content will be available online for the next 6-12 months.The next Competence web casts will be presented as follows: June the 4th  2012 September the 3rd  2012 December the 3rd  2012 March the 4th  2013. Note: Depending on local network bandwidth please allow some seconds time the presentations to download. You might want to refresh your screen by pressing F5. DurationMaximum 1 hour For further information please contact me at [email protected]. Best regards Markku RouhiainenDirector, Applications Partner EnablementWestern Europe

  Read the article

• XNA RenderTarget2D Sample

  - by Michael B. McLaughlin

  I remember being scared of render targets when I first started with XNA. They seemed like weird magic and I didn’t understand them at all. There’s nothing to be frightened of, though, and they are pretty easy to learn how to use. The first thing you need to know is that when you’re drawing in XNA, you aren’t actually drawing to the screen. Instead you’re drawing to this thing called the “back buffer”. Internally, XNA maintains two sections of graphics memory. Each one is exactly the same size as the other and has all the same properties (such as surface format, whether there’s a depth buffer and/or a stencil buffer, and so on). XNA flips between these two sections of memory every update-draw cycle. So while you are drawing to one, it’s busy drawing the other one on the screen. Then the current update-draw cycle ends, it flips, and the section you were just drawing to gets drawn to the screen while the one that was being drawn to the screen before is now the one you’ll be drawing on. This is what’s meant by “double buffering”. If you drew directly to the screen, the player would see all of those draws taking place as they happened and that would look odd and not very good at all. Those two sections of graphics memory are render targets. All a render target is, is a section of graphics memory to which things can be drawn. In addition to the two that XNA maintains automatically, you can also create and set your own using RenderTarget2D and GraphicsDevice.SetRenderTarget. Using render targets lets you do all sorts of neat post-processing effects (like bloom) to make your game look cooler. It also just lets you do things like motion blur and lets you create mirrors in 3D games. There are quite a lot of things that render targets let you do. To go along with this post, I wrote up a simple sample for how to create and use a RenderTarget2D. It’s available under the terms of the Microsoft Public License and is available for download on my website here: http://www.bobtacoindustries.com/developers/utils/RenderTarget2DSample.zip . Other than the ‘using’ statements, every line is commented in detail so that it should (hopefully) be easy to follow along with and understand. If you have any questions, leave a comment here or drop me a line on Twitter. One last note. While creating the sample I came across an interesting quirk. If you start by creating a Windows Game, and then make a copy for Windows Phone 7, the drop-down that lets you choose between drawing to a WP7 device and the WP7 emulator stays grayed-out. To resolve this, you need to right click on the Windows Phone 7 version in the Solution Explorer, and choose “Set as StartUp Project”. The bar will then become active, letting you change the target you which to deploy to. If you want another version to be the one that starts up when you press F5 to start debugging, just go and right-click on that version and choose “Set as StartUp Project” for it once you’ve set the WP7 target (device or emulator) that you want.

  Read the article

• SQL Server Date Comparison Functions

  - by HighAltitudeCoder

  A few months ago, I found myself working with a repetitive cursor that looped until the data had been manipulated enough times that it was finally correct.  The cursor was heavily dependent upon dates, every time requiring the earlier of two (or several) dates in one stored procedure, while requiring the later of two dates in another stored procedure. In short what I needed was a function that would allow me to perform the following evaluation: WHERE MAX(Date1, Date2) < @SomeDate The problem is, the MAX() function in SQL Server does not perform this functionality.  So, I set out to put these functions together.  They are titled: EarlierOf() and LaterOf(). /**********************************************************                               EarlierOf.sql   **********************************************************/ /**********************************************************   Return the later of two DATETIME variables.   Parameter 1: DATETIME1 Parameter 2: DATETIME2   Works for a variety of DATETIME or NULL values. Even though comparisons with NULL are actually indeterminate, we know conceptually that NULL is not earlier or later than any other date provided.   SYNTAX: SELECT dbo.EarlierOf('1/1/2000','12/1/2009') SELECT dbo.EarlierOf('2009-12-01 00:00:00.000','2009-12-01 00:00:00.521') SELECT dbo.EarlierOf('11/15/2000',NULL) SELECT dbo.EarlierOf(NULL,'1/15/2004') SELECT dbo.EarlierOf(NULL,NULL)   **********************************************************/ USE AdventureWorks GO   IF EXISTS       (SELECT *       FROM sysobjects       WHERE name = 'EarlierOf'       AND xtype = 'FN'       ) BEGIN             DROP FUNCTION EarlierOf END GO   CREATE FUNCTION EarlierOf (       @Date1                              DATETIME,       @Date2                              DATETIME )   RETURNS DATETIME   AS BEGIN       DECLARE @ReturnDate     DATETIME         IF (@Date1 IS NULL AND @Date2 IS NULL)       BEGIN             SET @ReturnDate = NULL             GOTO EndOfFunction       END         ELSE IF (@Date1 IS NULL AND @Date2 IS NOT NULL)       BEGIN             SET @ReturnDate = @Date2             GOTO EndOfFunction       END         ELSE IF (@Date1 IS NOT NULL AND @Date2 IS NULL)       BEGIN             SET @ReturnDate = @Date1             GOTO EndOfFunction       END         ELSE       BEGIN             SET @ReturnDate = @Date1             IF @Date2 < @Date1                   SET @ReturnDate = @Date2             GOTO EndOfFunction       END         EndOfFunction:       RETURN @ReturnDate   END -- End Function GO   ---- Set Permissions --GRANT SELECT ON EarlierOf TO UserRole1 --GRANT SELECT ON EarlierOf TO UserRole2 --GO                                                                                             The inverse of this function is only slightly different. /**********************************************************                               LaterOf.sql   **********************************************************/ /**********************************************************   Return the later of two DATETIME variables.   Parameter 1: DATETIME1 Parameter 2: DATETIME2   Works for a variety of DATETIME or NULL values. Even though comparisons with NULL are actually indeterminate, we know conceptually that NULL is not earlier or later than any other date provided.   SYNTAX: SELECT dbo.LaterOf('1/1/2000','12/1/2009') SELECT dbo.LaterOf('2009-12-01 00:00:00.000','2009-12-01 00:00:00.521') SELECT dbo.LaterOf('11/15/2000',NULL) SELECT dbo.LaterOf(NULL,'1/15/2004') SELECT dbo.LaterOf(NULL,NULL)   **********************************************************/ USE AdventureWorks GO   IF EXISTS       (SELECT *       FROM sysobjects       WHERE name = 'LaterOf'       AND xtype = 'FN'       ) BEGIN             DROP FUNCTION LaterOf END GO   CREATE FUNCTION LaterOf (       @Date1                              DATETIME,       @Date2                              DATETIME )   RETURNS DATETIME   AS BEGIN       DECLARE @ReturnDate     DATETIME         IF (@Date1 IS NULL AND @Date2 IS NULL)       BEGIN             SET @ReturnDate = NULL             GOTO EndOfFunction       END         ELSE IF (@Date1 IS NULL AND @Date2 IS NOT NULL)       BEGIN             SET @ReturnDate = @Date2             GOTO EndOfFunction       END         ELSE IF (@Date1 IS NOT NULL AND @Date2 IS NULL)       BEGIN             SET @ReturnDate = @Date1             GOTO EndOfFunction       END         ELSE       BEGIN             SET @ReturnDate = @Date1             IF @Date2 > @Date1                   SET @ReturnDate = @Date2             GOTO EndOfFunction       END         EndOfFunction:       RETURN @ReturnDate   END -- End Function GO   ---- Set Permissions --GRANT SELECT ON LaterOf TO UserRole1 --GRANT SELECT ON LaterOf TO UserRole2 --GO                                                                                             The interesting thing about this function is its simplicity and the built-in NULL handling functionality.  Its interesting, because it seems like something should already exist in SQL Server that does this.  From a different vantage point, if you create this functionality and it is easy to use (ideally, intuitively self-explanatory), you have made a successful contribution. Interesting is good.  Self-explanatory, or intuitive is FAR better.  Happy coding! Graeme

  Read the article

• Ti Launchpad

  - by raysmithequip

  Just thought I would get a couple of notes up here for reference to anyone that is interested...it is now Feb 2011 and I have not been posting here enough to remember this blog. Back in Nov 2010 I ordered the Ti launchpad msp430, it is a little target board kit replete with a mini USB cable, two very inexpensive programmable mcu's and a couple of pin headers with a couple of led's on board, a spi connector some on board jumpers and two programmable micro switches....all for less than $5.00...INCLUDING SHIPPING!!....not bad when the ardruino's are running around 20.00 for the target board, atmega328 and cable off of eBay...I wont even mention the microchip pic right now.  Naw, for $5.00 the Ti launchpad kit is about the cheapest fun around...if-uns your a geek that is... Well, the launchpad was backordered for almost two months, came like Xmas eve in fact...I had almost forgotten it!! And really, it was way late and not my idea of an Xmas present for myself.  That would of been the web expressions 4 I bought a few weeks back.  With all the holidays, I did not even look at it till last week, in fact I passed the wrapped board around at my local ham club meeting during points of personal privilege....some oh's and ahhs but mostly duhs...I actually ordered it to avoid downloading the huge code compressor studio 4 (CCS) that was supposed to be included on the cd.  No cd.  I had already downloaded IAR  another programming IDE for these little micro bugs. In my spare time I toyed with IAR and the launchpad board but after about two days of playing delete the driver with windows I decided to just download CCS 4, the code limited version, and give that a shot......CCS 4, is a good rewrite from the earlier versions, it is based on Eclipse as an IDE and includes the drivers for the msp430 target board I received in the kit.  Once installed I quickly configured the debugger for the target chip which was already plugged into the dip socket at the factory, msp430G2131 from he drop down list and clicked ok...I was in!! The CCS4 is full of bells and whistles compared to the IAR, which I would of preferred for the simplicity.  But the code compressor studio really does have it all!!..the code limited version is free, and of all things will give you java script editor box.  The whole layout in debugger mode reminds me of any modern programmer IDE...I mean sure give me Tex anytime but you simply must admire all the boxes and options included in the GUI.  It was a simple matter to check the assembly code in the flash and ram memory that came preloaded for the launchpad kit.  Assembly.  I am right now looking for my old assembly textbooks...sure I remember how to use mov and add etc but a couple of the commands are a little more than vague anymore.  Still, these little mcu's are about 50 cents each and might just work in a couple of projects I have lined up for the near future.  I may document the code here.  Luckily, I plan to write the code in c++ for the main project but if it has to be assembly, no prob.  For reference, the program that came already on the 2131 in the kit was a temperature indicator that alternately flashed red and green leds and changed the intensity of either depending on whether the temp was rising or falling...neat.  Neat enough that it might be worthwhile banging out a little GUI in windows 7 to test the new user device system calls, maybe put a temp gauge widget up on the desktop...just to keep from getting bored.  If you see some assembly code on this blog, you know I was doing something with one of the many mcu's out there.....thats all for now, more to follow...a bit later, of course.

  Read the article

• Friday Tips #6, Part 1

  - by Chris Kawalek

  We have a two parter this week, with this post focusing on desktop virtualization and the next one on server virtualization. Question: Why would I use the Oracle Secure Global Desktop Secure Gateway? Answer by Rick Butland, Principal Sales Consultant, Oracle Desktop Virtualization: Well, for the benefit of those who might not be familiar with client connections in Oracle Secure Global Desktop (SGD), let me back up and briefly explain. An SGD client connects to an SGD server using two distinct protocols, which, by default, require two distinct TCP ports. The first is the HTTP protocol, used by the web browser to connect to the SGD webserver on TCP port 80, or if secure connections are enabled (SSL/TLS), then TCP port 443, commonly identified as the "HTTPS" port, that is, "SSL encrypted HTTP." The second protocol from the client to the server is the Adaptive Internet Protocol, or AIP, which is used for displaying applications, transferring drive mapping data, print jobs, and so on. By default, AIP uses the TCP port 3104, or port 5307 when SSL is enabled. When SGD clients need to access SGD over a firewall, the ports that AIP requires are typically "closed"; and most administrators are reluctant, to put it mildly, to change their firewall configurations to allow AIP traffic on 3144/5307.   To avoid this problem, SGD introduced "Firewall Forwarding", a technique where, in effect, both http and AIP traffic are "multiplexed" onto a single "well-known" TCP port, that is port 443, the https port.  This is also known as single-port firewall traversal.  This technique takes advantage of the fact that, as a "well-known service", port 443 is usually "open",   allowing (encrypted) traffic to pass. At the target SGD server, the two protocols are de-multiplexed and routed appropriately. The Secure Gateway was developed in response to requirements from customers for SGD to support multi-stage DMZ's, and to avoid exposing SGD servers and the information they contain directly to connections from the Internet. The Secure Gateway acts as a reverse-proxy in the first-tier of the DMZ, accepting, authenticating, and terminating incoming client connections, and then re-encrypting the connections, and proxying them, routing them on to SGD servers, deeper in the network. The client no longer needs to know the name/IP address of the SGD servers in their network, they connect to the gateway, only. The gateway takes care of those internal network details.     The Secure Gateway supports the same "single-port firewall" capability as does "Firewall Forwarding", but offers the additional advantage of load-balancing incoming client connections amongst SGD array members, which could be cumbersome without a forward-deployed secure gateway. Load-balancing weights and policies can be monitored and tuned using the "Balancer Manager" application, and Apache mod_proxy_balancer directives.   Going forward, our architects recommend the use of the Secure Gateway over "Firewall Forwarding" for single-port firewall traversal, due to its architectural advantages, its greater flexibility and enhanced features.  Finally, it should be noted that the Secure Gateway is not separately priced; any licensed SGD customer may use the Secure Gateway component at no additional cost.   For more information, see the "Secure Gateway Administrator's Guide".

  Read the article

• Communication between state machines with hidden transitions

  - by slartibartfast

  The question emerged for me in embedded programming but I think it can be applied to quite a number of general networking situations e.g. when a communication partner fails. Assume we have an application logic (a program) running on a computer and a gadget connected to that computer via e.g. a serial interface like RS232. The gadget has a red/green/blue LED and a button which disables the LED. The LEDs color can be driven by software commands over the serial interface and the state (red/green/blue/off) is read back and causes a reaction in the application logic. Asynchronous behaviour of the application logic with regard to the LED color down to a certain delay (depending on the execution cycle of the application) is tolerated. What we essentially have is a resource (the LED) which can not be reserved and handled atomically by software because the (organic) user can at any time press the button to interfere/break the software attempt to switch the LED color. Stripping this example from its physical outfit I dare to say that we have two communicating state machines A (application logic) and G (gadget) where G executes state changes unbeknownst to A (and also the other way round, but this is not significant in our example) and only A can be modified at a reasonable price. A needs to see the reaction and state of G in one piece of information which may be (slightly) outdated but not inconsistent with respect to the short time window when this information was generated on the side of G. What I am looking for is a concise method to handle such a situation in embedded software (i.e. no layer/framework like CORBA etc. available). A programming technique which is able to map the complete behaviour of both participants on classical interfaces of a classical programming language (C in this case). To complicate matters (or rather, to generalize), a simple high frequency communication cycle of A to G and back (IOW: A is rapidly polling G) is out of focus because of technical restrictions (delay of serial com, A not always active, etc.). What I currently see as a general solution is: the application logic A as one thread of execution an adapter object (proxy) PG (presenting G inside the computer), together with the serial driver as another thread a communication object between the two (A and PG) which is transactionally safe to exchange The two execution contexts (threads) on the computer may be multi-core or just interrupt driven or tasks in an RTOS. The com object contains the following data: suspected state (written by A): effectively a member of the power set of states in G (in our case: red, green, blue, off, red_or_green, red_or_blue, red_or_off...etc.) command data (written by A): test_if_off, switch_to_red, switch_to_green, switch_to_blue operation status (written by PG): operation_pending, success, wrong_state, link_broken new state (written by PG): red, green, blue, off The idea of the com object is that A writes whichever (set of) state it thinks G is in, together with a command. (Example: suspected state="red_or_green", command: "switch_to_blue") Notice that the commands issued by A will not work if the user has switched off the LED and A needs to know this. PG will pick up such a com object and try to send the command to G, receive its answer (or a timeout) and set the operation status and new state accordingly. A will take back the oject once it is no longer at operation_pending and can react to the outcome. The com object could be separated of course (into two objects, one for each direction) but I think it is convenient in nearly all instances to have the command close to the result. I would like to have major flaws pointed out or hear an entirely different view on such a situation.

  Read the article

• Roles / Profiles / Perspectives in NetBeans IDE 7.1

  - by Geertjan

  With a check out of main-silver from yesterday, I'm able to use the brand new "role" attribute in @TopComponent.Registration, as you can see below, in the bit in bold: @ConvertAsProperties(dtd = "-//org.role.demo.ui//Admin//EN", autostore = false) @TopComponent.Description(preferredID = "AdminTopComponent", //iconBase="SET/PATH/TO/ICON/HERE", persistenceType = TopComponent.PERSISTENCE_ALWAYS) @TopComponent.Registration(mode = "editor", openAtStartup = true, role="admin") public final class AdminTopComponent extends TopComponent { And here's a window for general users of the application, with the "role" attribute set to "user": @ConvertAsProperties(dtd = "-//org.role.demo.ui//User//EN", autostore = false) @TopComponent.Description(preferredID = "UserTopComponent", //iconBase="SET/PATH/TO/ICON/HERE", persistenceType = TopComponent.PERSISTENCE_ALWAYS) @TopComponent.Registration(mode = "explorer", openAtStartup = true, role="user") public final class UserTopComponent extends TopComponent { So, I have two windows. One is assigned to the "admin" role, the other to the "user" role. In the "ModuleInstall" class, I add a "WindowSystemListener" and set "user" as the application's role: public class Installer extends ModuleInstall implements WindowSystemListener { @Override public void restored() { WindowManager.getDefault().addWindowSystemListener(this); } @Override public void beforeLoad(WindowSystemEvent event) { WindowManager.getDefault().setRole("user"); WindowManager.getDefault().removeWindowSystemListener(this); } @Override public void afterLoad(WindowSystemEvent event) { } @Override public void beforeSave(WindowSystemEvent event) { } @Override public void afterSave(WindowSystemEvent event) { } } So, when the application starts, the "UserTopComponent" is shown, not the "AdminTopComponent". Next, I have two Actions, for switching between the two roles, as shown below: @ActionID(category = "Window", id = "org.role.demo.ui.SwitchToAdminAction") @ActionRegistration(displayName = "#CTL_SwitchToAdminAction") @ActionReferences({ @ActionReference(path = "Menu/Window", position = 250) }) @Messages("CTL_SwitchToAdminAction=Switch To Admin") public final class SwitchToAdminAction extends AbstractAction { @Override public void actionPerformed(ActionEvent e) { WindowManager.getDefault().setRole("admin"); } @Override public boolean isEnabled() { return !WindowManager.getDefault().getRole().equals("admin"); } } @ActionID(category = "Window", id = "org.role.demo.ui.SwitchToUserAction") @ActionRegistration(displayName = "#CTL_SwitchToUserAction") @ActionReferences({ @ActionReference(path = "Menu/Window", position = 250) }) @Messages("CTL_SwitchToUserAction=Switch To User") public final class SwitchToUserAction extends AbstractAction { @Override public void actionPerformed(ActionEvent e) { WindowManager.getDefault().setRole("user"); } @Override public boolean isEnabled() { return !WindowManager.getDefault().getRole().equals("user"); } } When I select one of the above actions, the role changes, and the other window is shown. I could, of course, add a Login dialog to the "SwitchToAdminAction", so that authentication is required in order to switch to the "admin" role. Now, let's say I am now in the "user" role. So, the "UserTopComponent" shown above is now opened. I decide to also open another window, the Properties window, as below... ...and, when I am in the "admin" role, when the "AdminTopComponent" is open, I decide to also open the Output window, as below... Now, when I switch from one role to the other, the additional window/s I opened will also be opened, together with the explicit members of the currently selected role. And, the main window position and size are also persisted across roles. When I look in the "build" folder of my project in development, I see two different Windows2Local folders, one per role, automatically created by the fact that there is something to be persisted for a particular role, e.g., when a switch to a different role is done: And, with that, we now clearly have roles/profiles/perspectives in NetBeans Platform applications from NetBeans Platform 7.1 onwards.

  Read the article

• Elo system behaves oddly in program I've created

  - by adc

  Alright, so I'm looking to build a small program (C# and XAML) that, essentially, does this: Generate array of players. Each player has a current rating and a true rating. I set current rating to 1200 as a starting point right now; I've also tried setting it to true rating and the average of the two. True rating is what their skill level actually is. Their true rating is calculated based on percentages from the current League of Legends rating system; generating an array of 970 thousand generates results very similar to the data from here: (removed due to URL limit - but trust me, the results are very similar). This array is of length specified by the user. If need be, sort the array from smallest to largest. Play X number of games, again specified by the user. This is done by taking the array of players (which is sorted by Current Rating after being created) and running through it in groups of 10. The first five are on team one, the second five are on team two. It then takes the True Rating of these players and calculates an expected chance to win using the Elo system. It generates a random double and compares it to the expected chance to win; if the number is lower, team one wins - otherwise team two wins. I then update the rating of the players via, again, the Elo system - giving the winning team a score of 1 and the losing team a score of 0. I use a K value of 36 (but have tried 12, 24, and even higher ones) and an F value of 400. After going through the entire loop of players (which I have conveniently forced to be a multiple of ten), it sorts the array - again via current rating. This, if my understanding of the Elo system is correct, runs properly. However, it doesn't seem to work. I have a running test telling me how many players of the full array are within 100 current rating of their true rating. I would expect some portion of the population to be outside this range (as probability is not always going to go in their favor), but a full 40-45% of the population is outside of this range. I also have it outputting the maximum difference between true and current rating - and I have never seen this drop below 500! It hovers between 550-600, occasionally going over or under. I'm at a loss as to what to change - I've fiddled with the K and F values, where I start all the players, etc. but nothing changes the fact that eventually a good 40% of the population is outside the range. And it isn't that I have it playing too few games - it's now run through over 60 thousand games and the problem never disappears or really fluctuates. The full C# code, including everything except the XAML file and the Player class (pastebin is being very slow and I can only post two links, so I can't link to the XAML file): http://pastebin.com/rFcZRL84 The Player class: http://pastebin.com/4cJTdTRu I guess my question is did I do anything wrong? Is there a problem with the way I implemented the system, or is it just that Riot uses a significantly modified Elo system? I don't think it's the latter, as that still wouldn't explain the massive true and current rating differences to me, however.

  Read the article

• Circle-Line Collision Detection Problem

  - by jazzdawg

  I am currently developing a breakout clone and I have hit a roadblock in getting collision detection between a ball (circle) and a brick (convex polygon) working correctly. I am using a Circle-Line collision detection test where each line represents and edge on the convex polygon brick. For the majority of the time the Circle-Line test works properly and the points of collision are resolved correctly. Collision detection working correctly. However, occasionally my collision detection code returns false due to a negative discriminant when the ball is actually intersecting the brick. Collision detection failing. I am aware of the inefficiency with this method and I am using axis aligned bounding boxes to cut down on the number of bricks tested. My main concern is if there are any mathematical bugs in my code below. /* * from and to are points at the start and end of the convex polygons edge. * This function is called for every edge in the convex polygon until a * collision is detected. */ bool circleLineCollision(Vec2f from, Vec2f to) { Vec2f lFrom, lTo, lLine; Vec2f line, normal; Vec2f intersectPt1, intersectPt2; float a, b, c, disc, sqrt_disc, u, v, nn, vn; bool one = false, two = false; // set line vectors lFrom = from - ball.circle.centre; // localised lTo = to - ball.circle.centre; // localised lLine = lFrom - lTo; // localised line = from - to; // calculate a, b & c values a = lLine.dot(lLine); b = 2 * (lLine.dot(lFrom)); c = (lFrom.dot(lFrom)) - (ball.circle.radius * ball.circle.radius); // discriminant disc = (b * b) - (4 * a * c); if (disc < 0.0f) { // no intersections return false; } else if (disc == 0.0f) { // one intersection u = -b / (2 * a); intersectPt1 = from + (lLine.scale(u)); one = pointOnLine(intersectPt1, from, to); if (!one) return false; return true; } else { // two intersections sqrt_disc = sqrt(disc); u = (-b + sqrt_disc) / (2 * a); v = (-b - sqrt_disc) / (2 * a); intersectPt1 = from + (lLine.scale(u)); intersectPt2 = from + (lLine.scale(v)); one = pointOnLine(intersectPt1, from, to); two = pointOnLine(intersectPt2, from, to); if (!one && !two) return false; return true; } } bool pointOnLine(Vec2f p, Vec2f from, Vec2f to) { if (p.x >= min(from.x, to.x) && p.x <= max(from.x, to.x) && p.y >= min(from.y, to.y) && p.y <= max(from.y, to.y)) return true; return false; }

  Read the article

• VMware vSphere cluster design for site redundancy

  - by Stefan Radovanovici

  I have a question about the best design for site redudancy when using vSphere clusters. A bit of background info about our situation first though. We are a medium-sized company with two main offices, located in different countries. Our networks are linked by a Layer2 150Mbps leased line which is currently underused. We have a variety of services running for internal use within the company, some on physycal servers and some on existing vSphere clusters. In our department we also run several services (almost all running under various forms of Linux) like NTP, Syslog, jump servers, monitoring servers and so on. We have now the requirement that those servers need to be redundant within each location (which they are not at the moment) and also site redudant (which they are to some extent, the servers are duplicated in the 2nd location with configurations kept in sync via various methods at the application layer). There is no SAN available for us, at least not something that we can use at the moment. Cost is also an issue. While we do have some budget available for this, we can't afford to buy SANs for both locations for example. I looked at the VSA feature and it seems that this could be something for us but I am unsure how to solve the site-redudancy requirement. At the moment for testing purposes I am setting up in a lab a vSphere 5 with VSA on two ESXi hosts. I am currently using the Essentials Plus kit with VSA license, which allows me to build a VSA cluster on up to 3 hosts, together with a vCenter license to manage them. The hosts each have two dual-port network cards and two 600GB drives, running in Raid1. Hardware-wise this will be enough for us to run the all the services we need as VMs and will provide redundandcy within the site. At the moment I see only two option to have site redundancy: build an identical VSA cluter in the second location and keep the various services sync'ed at application layer (database sync, rsync and so on). simply move one of the hosts from the existing cluster to the second location, basically having the VSA cluster span the 150Mbps link between the sites. I would very much prefer the second option but I am unsure how well it'll work, if it can work at all. Technically it should, we can span the needed VLANs across the leased line and have them available in the second location. The advantage would be that we don't need to worry at all about sync'ing databases and the like. But I have the feeling that the bandwidth will not be enough, I have no way of knowing how much traffic will the VSA cluster generate between the hosts. I realize that this will most likely depend on the individual usage of the VMs but still, I have no idea how VSA replicates data between the ESXi hosts. Are these my only options or can my goals be achieved in some other way ? Is there perhaps a way to have some sort of "cold stand by" cluster in the second location where the VMs would be sync'ed once per night from the main location ? The idea is that in case the first site becomes unavailable, we would be able to bring all those VMs online there. We would be ok with the data being 1 day old. Any answers are appreciated. Best regards, Stefan

  Read the article

• lvm disappeared after disc replacement on raid10

  - by user142295

  here my problem: I am running ubuntu 12.04 on a raid10 (4 disks), on top of which I installed an lvm with two volume groups (one for /, one for /home). The layout of the disks are as follows: Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0003f3b6 Device Boot Start End Blocks Id System /dev/sda1 * 63 481949 240943+ 83 Linux /dev/sda2 481950 2910640634 1455079342+ fd Linux raid autodetect /dev/sda3 2910640635 2930272064 9815715 82 Linux swap / Solaris Disk /dev/sdb: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00069785 Device Boot Start End Blocks Id System /dev/sdb1 63 2910158684 1455079311 fd Linux raid autodetect /dev/sdb2 2910158685 2930272064 10056690 82 Linux swap / Solaris Disk /dev/sdc: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 63 2910158684 1455079311 fd Linux raid autodetect /dev/sdc2 2910158685 2930272064 10056690 82 Linux swap / Solaris Disk /dev/sdd: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000f14de Device Boot Start End Blocks Id System /dev/sdd1 63 2910158684 1455079311 fd Linux raid autodetect /dev/sdd2 2910158685 2930272064 10056690 82 Linux swap / Solaris The first disk (/dev/sda) contains the /boot partition on /dev/sda1. I use grub2 to boot the system off this partition. On top of this raid10 I installed two volume groups, one for /, one for /home. This system worked well, I even exchanged two disks during the last two years. It always worked. But not this time. For the first time, /dev/sda broke. I do not know if this is an issue – I know I would have struggled anyways to overcome the problem with /boot installed on that disk and grub2 installed on the mbr of /dev/sda. Anyways, I did what I always did: start knoppix fire up the raid sudo mdadm --examine -scan which returns ARRAY /dev/md127 UUID=0dbf4558:1a943464:132783e8:19cdff95 start it up sudo mdadm --assemble /dev/md127 fail the failing disk (smart event) sudo mdadm /dev/md127 --fail /dev/sda2 remove the failing disk sudo mdadm /dev/md127 --remove /dev/sda2 stop the raid sudo mdadm -S /dev/md127 take out the disk replace it with a new one create the same partitions as on the failling one add it to the raid sudo mdadm --assemble /dev/md127 sudo mdadm /dev/md127 --add /dev/sda2 wait 4 hours All looks fine: cat /proc/mdstat returns: Personalities : [raid10] md127 : active raid10 sda2[0] sdd1[3] sdc1[2] sdb1[1] 2910158464 blocks 64K chunks 2 near-copies [4/4] [UUUU] unused devices: <none> and sudo mdadm --detail /dev/md127 returns /dev/md127: Version : 0.90 Creation Time : Wed Jun 10 13:08:46 2009 Raid Level : raid10 Array Size : 2910158464 (2775.34 GiB 2980.00 GB) Used Dev Size : 1455079232 (1387.67 GiB 1490.00 GB) Raid Devices : 4 Total Devices : 4 Preferred Minor : 127 Persistence : Superblock is persistent Update Time : Thu Mar 21 16:27:40 2013 State : clean Active Devices : 4 Working Devices : 4 Failed Devices : 0 Spare Devices : 0 Layout : near=2 Chunk Size : 64K UUID : 0dbf4558:1a943464:132783e8:19cdff95 (local to host Microknoppix) Events : 0.4824680 Number Major Minor RaidDevice State 0 8 2 0 active sync /dev/sda2 1 8 17 1 active sync /dev/sdb1 2 8 33 2 active sync /dev/sdc1 3 8 49 3 active sync /dev/sdd1 However, there is no trace of the volume groups. Rebooting into knoppix does not help Restarting the old system (I actually replugged and re-added the failing disk for that – the system begins to start, but then fails to see the / partition – no wonder if the volume group is gone) does not help. sudo vgscan, sudo vgdisplay, sudo lvs, sudo lvdisplay, sudo vgscan –mknodes all returned No volume groups found. I am completely at a loss. Can anyone tell me if and how I can recover my data? Thanks in advance!

  Read the article

• Basic collision direction detection on 2d objects

  - by Osso Buko

  I am trying to develop a platform game for Android by using ANdroid GL Engine (ANGLE). And I am having trouble with collision detection. I have two objects which is shaped as rectangular. And no change in rotation. Here is a scheme of attributes of objects. What i am trying to do is when objects collide they block each other's movement on that direction. Every object has 4 boolean (bTop, bBottom, bRight, bLeft). For example when bBottom is true object can't advance on that direction. I came up with a solution but it seems it only works on one dimensional. Bottom and top or right and left. public void collisionPlatform (MyObject a, MyObject b) { // first obj is player and second is a wall or a platform Vector p1 = a.mPosition; // p1 = middle point of first object Vector d1 = a.mPosition2; // width(mX) and height of first object Vector mSpeed1 = a.mSpeed; // speed vector of first object Vector p2 = b.mPosition; // p1 = middle point of second object Vector d2 = b.mPosition2; // width(mX) and height of second object Vector mSpeed2 = b.mSpeed; // speed vector of second object float xDist, yDist; // distant between middle of two object float width , height; // this is average of two objects measurements width=(width1+width2)/2 xDist=(p1.mX - p2.mX); // calculate distance // if positive first object is at the right yDist=(p1.mY - p2.mY); // if positive first object is below width = d1.mX + d2.mX; // average measurements calculate height = d1.mY + d2.mY; width/=2; height/=2; if (Math.abs(xDist) < width && Math.abs(yDist) < height) { // Two object is collided if(p1.mY>p2.mY) { // first object is below second one a.bTop = true; if(a.mSpeed.mY<0) a.mSpeed.mY=0; b.bBottom = true; if(b.mSpeed.mY>0) b.mSpeed.mY=0; } else { a.bBottom = true; if(a.mSpeed.mY>0) a.mSpeed.mY=0; b.bTop = true; if(b.mSpeed.mY<0) b.mSpeed.mY=0; } } As seen in my code it simply will not work. when object comes from right or left it doesn't work. I tried couple of ways other than this one but none worked. I am guessing right method will include mSpeed vector. But I have no idea how to do it. I really appreciate if you could help. Sorry for my bad english.

  Read the article

• Juggling with JDKs on Apple OS X

  - by Blueberry Coder

  I recently got a shiny new MacBook Pro to help me support our ADF Mobile customers. It is really a wonderful piece of hardware, although I am still adjusting to Apple's peculiar keyboard layout. Did you know, for example, that the « delete » key actually performs a « backspace »? But I disgress... As you may know, ADF Mobile development still requires JDeveloper 11gR2, which in turn runs on Java 6. On the other hand, JDeveloper 12c needs JDK 7. I wanted to install both versions, and wasn't sure how to do it.   If you remember, I explained in a previous blog entry how to install JDeveloper 11gR2 on Apple's OS X. The trick was to use the /usr/libexec/java_home command in order to invoke the proper JDK. In this case, I could have done the same thing; the two JDKs can coexist without any problems, since they install in completely different locations. But I wanted more than just installing JDeveloper. I wanted to be able to select my JDK when using the command line as well. On Windows, this is easy, since I keep all my JDKs in a central location. I simply have to move to the appropriate folder or type the folder name in the command I want to execute. Problem is, on OS X, the paths to the JDKs are... let's say convoluted.  Here is the one for Java 6. /System/Library/Java/JavaVirtualMachines/1.6.0.jdk/Contents/Home The Java 7 path is not better, just different. /Library/Java/JavaVirtualMachines/jdk1.7.0_45.jdk/Contents/Home Intuitive, isn't it? Clearly, I needed something better... On OS X, the default command shell is bash. It is possible to configure the shell environment by creating a file named « .profile » in a user's home folder. Thus, I created such a file and put the following inside: export JAVA_7_HOME=$(/usr/libexec/java_home -v1.7) export JAVA_6_HOME=$(/usr/libexec/java_home -v1.6) export JAVA_HOME=$JAVA_7_HOME alias java6='export JAVA_HOME=$JAVA_6_HOME' alias java7='export JAVA_HOME=$JAVA_7_HOME'  The first two lines retrieve the current paths for Java 7 and Java 6 and store them in two environment variables. The third line marks Java 7 as the default. The last two lines create command aliases. Thus, when I type java6, the value for JAVA_HOME is set to JAVA_6_HOME, for example.  I now have an environment which works even better than the one I have on Windows, since I can change my active JDK on a whim. Here a sample, fresh from my terminal window. fdesbien-mac:~ fdesbien$ java6 fdesbien-mac:~ fdesbien$ java -version java version "1.6.0_65" Java(TM) SE Runtime Environment (build 1.6.0_65-b14-462-11M4609) Java HotSpot(TM) 64-Bit Server VM (build 20.65-b04-462, mixed mode) fdesbien-mac:~ fdesbien$ fdesbien-mac:~ fdesbien$ java7 fdesbien-mac:~ fdesbien$ java -version java version "1.7.0_45" Java(TM) SE Runtime Environment (build 1.7.0_45-b18) Java HotSpot(TM) 64-Bit Server VM (build 24.45-b08, mixed mode) fdesbien-mac:~ fdesbien$ Et voilà! Maximum flexibility without downsides, just I like it. 

  Read the article

• How to display a flyout menu on clicking an image in Grid header in MVC?

  - by Vincent

  A grid is displayed using the following code in MVC. <%= this.Grid( "routes-" + mc , "Testing", Model.Routes, new GridBuilder<RouteModel>() .Column( "chk", () => Html.Image( Url.Content( "down.gif" ), "Select or deselect tests" ), (m) => "<input type='hidden' name='routeLinkId' value='"+ m.RouteLinkID +"' />" + Html.CheckBox( "drugRoute" + mc + m.RouteLinkID, m.IsChecked ) ) .Column( "route clip-text", "Route", (m) = Html.Encode( m.Route ) ) .Column( "groups clip-text", "Groups", (m) = "" + Html.Encode(m.Group) + "" ) .ToGrid() ) % On clicking the image in header I need to display a flyout menu. The code for the flyout menu is below. <div id="group-menu-<%= mc %>" class="flyout-menu" title="Select tests"> <div> <p>Select</p> <ul> <li><button type="button" name="one">One</button></li> <li><button type="button" name="two">two</button></li> </ul> <p>Unselect</p> <ul> <li><button type="button" name="unselect-one">one</button></li> <li><button type="button" name="unselect-two">two</button></li> </ul> </div> </div> Now how do I display this menu on clicking the image in header.

  Read the article

• How to maintain a job history using Quartz scheduler

  - by rwwilden

  I'd like to maintain a history of jobs that were scheduled by a Quartz scheduler containing the following properties: 'start time', 'end time', 'success', 'error'. There are two interfaces available for this: ITriggerListener and IJobListener (I'm using the C# naming convention for interfaces because I'm using Quartz.NET but the same question could be asked for the Java version). IJobListener has a JobToBeExecuted and a JobWasExecuted method. The latter provides a JobExecutionException so that you know when something went wrong. However, there is no way to correlate JobToBeExecuted and JobWasExecuted. Suppose my job runs for ten minutes. I start it at t0 and t0+2 (so they overlap). I get two calls to JobToBeExecuted and insert two start times into my history table. When both jobs finish at t1 and t1+2 I get two calls to JobWasExecuted. How do I know what database record to update in each call (to store an end time with its corresponding start time)? ITriggerListener has another problem. There is no way to get any errors inside the TriggerComplete method when a job failed. How do I get the desired behavior?

  Read the article

• Sql Querying, group relationships

  - by Jordan

  Hi, Suppose I have two tables: Group ( id integer primary key, someData1 text, someData2 text ) GroupMember ( id integer primary key, group_id foreign key to Group.id, someData text ) I'm aware that my SQL syntax is not correct :) Hopefully is clear enough. My problem is this: I want to load a group record and all the GroupMember records associated with that group. As I see it, there are two options. A single query: SELECT Group.id, Group.someData1, Group.someData2 GroupMember.id, GroupMember.someData FROM Group INNER JOIN GroupMember ... WHERE Group.id = 4; Two queries: SELECT id, someData2, someData2 FROM Group WHERE id = 4; SELECT id, someData FROM GroupMember WHERE group_id = 4; The first solution has the advantage of only being one database round trip, but has the disadvantage of returning redundant data (All group data is duplicated for every group member) The second solution returns no duplicate data but involves two round trips to the database. What is preferable here? I suppose there's some threshold such that if the group sizes become sufficiently large, the cost of returning all the redundant data is going to be greater than the overhead involved with an additional database call. What other things should I be thinking about here? Thanks, Jordan

  Read the article

• make focusable element unfocusable on webkit

  - by Bill Keese

  When a node has a tabIndex setting (other than -1), clicking it will give it focus. Removing the tabIndex setting should stop that behavior, so that clicking has no effect. However, on webkit, once a node has a tabIndex, even after tabIndex is removed, the node can still be clicked and focused. Setting tabIndex=-1 also has the same click problem. Anyone know a workaround to this problem? <div id="one">one (no initial tabindex)</div> <div id="two" tabindex=0>two (initially tabindex=0)</div> <button type=button onclick="document.getElementById('one').setAttribute('tabindex', 0)">set tabindex on first div</button> <button type=button onclick="document.getElementById('one').removeAttribute('tabindex', 0)">remove tabindex on first div</button> <button type=button onclick="document.getElementById('two').removeAttribute('tabindex', 0)">remove tabindex on second div</button> <button type=button onclick="document.getElementById('one').setAttribute('tabindex', -1)">set tabindex=1 on first div</button> <button type=button onclick="document.getElementById('two').setAttribute('tabindex', -1)">set tabindex=1 on second div</button>

  Read the article

• Address Match Key Algorithm

  - by sestocker

  I have a list of addresses in two separate tables that are slightly off that I need to be able to match. For example, the same address can be entered in multiple ways: 110 Test St 110 Test St. 110 Test Street Although simple, you can imagine the situation in more complex scenerios. I am trying to develop a simple algorithm that will be able to match the above addresses as a key. For example. the key might be "11TEST" - first two of 110, first two of Test and first two of street variant. A full match key would also include first 5 of the zipcode as well so in the above example, the full key might look like "11TEST44680". I am looking for ideas for an effective algorithm or resources I can look at for considerations when developing this. Any ideas can be pseudo code or in your language of choice. We are only concerned with US addresses. In fact, we are only looking at addresses from 250 zip codes from Ohio and Michigan. We also do not have access to any postal software although would be open to ideas for cost effective solutions (it would essentially be a one time use). Please be mindful that this is an initial dump of data from a government source so suggestions of how users can clean it are helpful as I build out the application but I would love to have the best initial I possibly can by being able to match addresses as best as possible.

  Read the article

• Java: volatile guarantees and out-of-order execution

  - by WizardOfOdds

  Note that this question is solely about the volatile keyword and the volatile guarantees: it is not about the synchronized keyword (so please don't answer "you must use synchronize" for I don't have any issue to solve: I simply want to understand the volatile guarantees (or lack of guarantees) regarding out-of-order execution). Say we have an object containing two volatile String references that are initialized to null by the constructor and that we have only one way to modify the two String: by calling setBoth(...) and that we can only set their references afterwards to non-null reference (only the constructor is allowed to set them to null). For example (it's just an example, there's no question yet): public class SO { private volatile String a; private volatile String b; public SO() { a = null; b = null; } public void setBoth( @NotNull final String one, @NotNull final String two ) { a = one; b = two; } public String getA() { return a; } public String getB() { return b; } } In setBoth(...), the line assigning the non-null parameter "a" appears before the line assigning the non-null parameter "b". Then if I do this (once again, there's no question, the question is coming next): if ( so.getB() != null ) { System.out.println( so.getA().length ); } Am I correct in my understanding that due to out-of-order execution I can get a NullPointerException? In other words: there's no guarantee that because I read a non-null "b" I'll read a non-null "a"? Because due to out-of-order (multi)processor and the way volatile works "b" could be assigned before "a"? volatile guarantees that reads subsequent to a write shall always see the last written value, but here there's an out-of-order "issue" right? (once again, the "issue" is made on purpose to try to understand the semantics of the volatile keyword and the Java Memory Model, not to solve a problem).

  Read the article

• WPF/SL EventAggregator implementation with durable subscribers behavior?

  - by sha1dy

  Hi. Currently I'm building an application using latest Prism for Silverlight 4. I've a module and in that module I've two views with view models. Also I've a module view with two regions for each view. In module initialization I'm registering my views and view models in Unity container and also register views with corresponding regions. The problem is that views should display something similar to table-detail information - first view shows available entities ans the second view shows detail of selected entity. I need a way how to pass them initial selected entity. Newly created first view doesn't have any selected entity and newly created second view doesn't show any details. Currently I'm doing that this way: In module I create two view models and register them as instances in Unity container and then I register views as types for corresponding regions. Each view subscribes to EntitySelectedEvent from EventAggregator. Module initializer publish this event after initialization and this way two views are selecting the same entity. I know this looks ugly - I tried publishing this event from one of view models but the problems is that EventAggregator in Prism doesn't support durable subscribers - this means that if the second view model didn't subscribe to event before the first view model fired it, it won't receive and event. I know this is a normal behavior of EventAggregator, but I'm looking for a solution when view models can fire events without depending on initialization order of them - that is the first model can fire event before the second model was created and the second model will receive this 'queued' event after subscribing to it. Are there any other messaging implementations for WPF/SL which do support such behavior or using a mediator (in my example it's a module itself) isn't such a bad idea after all? One big problem with mediator is that models must be created right away in initialize and they can't be registered as types in container because this leads again to missing subscribers.

  Read the article

< Previous Page | 183 184 185 186 187 188 189 190 191 192 193 194  | Next Page >