Search Results

Search found 5638 results on 226 pages for 'debian sys maint'.

Page 19/226 | < Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >

• Adding Extra Hard Drives Debian Fdisk

  - by Belgin Fish

  well I just got a new server and it's a little different than what I'm use to, when I run cfdisk I get WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 1 267350 2147483647+ ee GPT Partition 1 does not start on physical sector boundary. WARNING: GPT (GUID Partition Table) detected on '/dev/sdb'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdb: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 267350 2147483647+ ee GPT Partition 1 does not start on physical sector boundary. WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdc: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 1 267350 2147483647+ ee GPT Partition 1 does not start on physical sector boundary. WARNING: GPT (GUID Partition Table) detected on '/dev/sdd'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdd: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdd1 1 267350 2147483647+ ee GPT Partition 1 does not start on physical sector boundary. WARNING: GPT (GUID Partition Table) detected on '/dev/sdf'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdf: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdf1 1 267350 2147483647+ ee GPT Partition 1 does not start on physical sector boundary. WARNING: GPT (GUID Partition Table) detected on '/dev/sde'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sde: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sde1 1 267350 2147483647+ ee GPT Partition 1 does not start on physical sector boundary. Usually it tells me which ones arn't partitioned and stuff, and I only have 6 drives in my server and there's 6 showing up here so I'm only assuming the first ones already mounted and formatted correctly? I'm not really sure if anyone would help me out here. Basically I just want to format and mount these drives :)

  Read the article

• Howto Nginx + git-http-backend + fcgiwrap (Debian Squeeze)

  - by brainsqueezer

  I am trying to setup git-http-backend with Nginx but after 24 hours wasting time and reading everything I could I think this config should work but doesn't. server { listen 80; server_name mydevserver; access_log /var/log/nginx/dev.access.log; error_log /var/log/nginx/dev.error.log; location / { root /var/repos; } location ~ /git(/.*) { gzip off; root /usr/lib/git-core; fastcgi_pass unix:/var/run/fcgiwrap.socket; include /etc/nginx/fastcgi_params2; fastcgi_param SCRIPT_FILENAME /usr/lib/git-core/git-http-backend; fastcgi_param DOCUMENT_ROOT /usr/lib/git-core/; fastcgi_param SCRIPT_NAME git-http-backend; fastcgi_param GIT_HTTP_EXPORT_ALL ""; fastcgi_param GIT_PROJECT_ROOT /var/repos; fastcgi_param PATH_INFO $1; #fastcgi_param PATH_TRANSLATED $document_root$fastcgi_path_info; } } Content of /etc/nginx/fastcgi_params2 fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; fastcgi_param REMOTE_USER $remote_user; # required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; but config seems not working $ git clone http://mydevserver/git/myprojectname/ Cloning into myprojectname... warning: remote HEAD refers to nonexistent ref, unable to checkout. and I can request an unexistant project and I will get the same answer $ git clone http://mydevserver/git/thisprojectdoesntexist/ Cloning into thisprojectdoesntexist... warning: remote HEAD refers to nonexistent ref, unable to checkout. If I change root to /usr/lib I will get a 403 error and this will be reported to nginx error log: 2011/11/23 15:52:46 [error] 5224#0: *55 FastCGI sent in stderr: "Cannot get script name, is DOCUMENT_ROOT and SCRIPT_NAME set and is the script executable?" while reading response header from upstream, client: 198.168.0.4, server: mydevserver, request: "GET /git/myprojectname/info/refs HTTP/1.1", upstream: "fastcgi://unix:/var/run/fcgiwrap.socket:", host: "mydevserver" My main trouble is with the correct root value with this configuration. Maybe there are some permissions problems. Notes: /var/repos/ is owned by www-data and contains folders bit git bare repos. All this works perfectly using ssh. If I go with my browser to http://mydevserver/git/myproject/info/refs it is answered by git-http-backend asking me to send a command. /var/run/fcgiwrap.socket has 777 permissions.

  Read the article

• Running python script in incrontab in Debian

  - by WilliamMayor

  I have a user, dropbox, that runs the Dropbox daemon, I want to monitor the directories in the Dropbox directory for new files and run a python script when they appear. I have the python script that I know works: $ /home/dropbox/monitor.py Trying to get lock Got lock, waiting for Dropbox to be idle Dropbox idle Finding instructions Done, releasing lock I have an incrontab entry: $ incrontab -l /home/dropbox/Dropbox IN_CREATE /home/dropbox/monitor.py | logger /home/dropbox/test IN_CREATE logger "$$ $@ $# $% $&" When I add a file to the test directory I see the output in /var/log/syslog: $ touch /home/dropbox/test/a $ tail /var/log/syslog ... Nov 9 10:18:27 vps incrond[1354]: (dropbox) CMD (logger "$ /home/dropbox/test a IN_CREATE 256") Nov 9 10:18:27 vps logger: "$ /home/dropbox/test a IN_CREATE 256" ... However, when I add a file to the Dropbox directory the command doesn't seem to run: $ touch /home/dropbox/Dropbox/a $ tail /var/log/syslog ... Nov 9 10:24:16 vps incrond[1354]: (dropbox) CMD (/home/dropbox/monitor.py | logger) ... So the incron daemon notices the new file and the correct command is found to be executed but it never actually gets executed. Nor are there any error messages. It kind of seems like incrontab can only be used to run the most simple of commands. This might be a similar question to: Incrond running but not executing commands CentOS 6.4 but I think that I don't have env problems, every path is absolute. I tried changing .../monitor.py to /usr/bin/python2.7 .../monitor.py just in case but it didn't make any difference.

  Read the article

• Debian wheezy keyboard shortcut for both opening and closing a terminal

  - by Peter

  I recently installed tilda and I would like to open it and close with the same keyboard shortcut. I wrote little something in bash that closes tilda if it is open and opens tilda when there is no such a process in ps -ef. It looks like this: a=ps -ef | fgrep -i tilda | cut -d' ' -f4 | head -1;if [ $a ] ; then kill $a; else tilda; fi It seems to be working (at least partially) when I commit this in terminal, but when I assign this command to specific keyboard shortcut (for example alt+1) it does nothing. Any suggestions? btw. is it possible to assign this shortcut for button '`' like in Quake?

  Read the article

• Debian: video problems with VLC

  - by kemp

  I have a problem playing AVI divx files with VLC. Yesterday upon start VLC showed an error message complaining about divx codecs and refused to proceed. Today the player starts but the video is squashed horizontally (it occupies roughly 1/4th of the VLC window which is for the other part black). I'm on an updated testing system, and before yesterday VLC was playing fine. In the meantime - after a recent dist-upgrade - I cannot run X with proprietary ATI drivers anymore, I have to use the FOSS radeonhd ones instead. I don't know if that's related but I thought it could be worth mentioning (and by the way if anyone has suggestions about this problem too, that'd be very much appreciated). How can I fix VLC's problem?

  Read the article

• server host name and server ip address redirect (Debian, Apache)

  - by Matthias Reisner

  I have the following folder structure on my apache! .../var/www/www.x.tt/htdocs .../var/www/www.y.tt/htdocs I have defined a virtual host for each. So if I type in www.x.tt in my browser I get to the www.x.tt site. And the same for www.y.tt. But now my question! If I type in the server address or the server host name I get to the ../var/www directory but I want that the user will be redirected to the www.x.tt site! Do I have to create a new virtual host for this problem or is it also possible only to add a .htaccess Rule?! Thanks!

  Read the article

• dpkg broken while upgrading Debian Etch to Lenny

  - by artvolk

  Good day! While trying to recover a box to lenny it seems I've broken things. It upgrades libc and glib after that dpkg seems to be broken. I can run apt-get, but it gets segmentation fault from dpkg: # apt-get -f install Reading package lists... Done Building dependency tree... Done 0 upgraded, 0 newly installed, 0 to remove and 316 not upgraded. 9 not fully installed or removed. Need to get 0B of archives. After unpacking 0B of additional disk space will be used. /bin/sh: line 1: 4606 Segmentation fault /usr/sbin/dpkg-preconfigure --apt E: Sub-process /usr/bin/dpkg received a segmentation fault. I can login via SSH but even ls is not working: # ls Segmentation fault Is there anything I can do remotelly via SSH? # ldd /bin/ls linux-gate.so.1 => (0xffffe000) librt.so.1 => /lib/tls/i686/cmov/librt.so.1 (0xb7fc8000) libacl.so.1 => /lib/libacl.so.1 (0xb7fc2000) libselinux.so.1 => /lib/libselinux.so.1 (0xb7fac000) libc.so.6 => /lib/i686/cmov/libc.so.6 (0xb7e51000) libpthread.so.0 => /lib/tls/i686/cmov/libpthread.so.0 (0xb7e3f000) /lib/ld-linux.so.2 (0xb7fd8000) libattr.so.1 => /lib/libattr.so.1 (0xb7e3b000) libdl.so.2 => /lib/i686/cmov/libdl.so.2 (0xb7e37000) libsepol.so.1 => /lib/libsepol.so.1 (0xb7df6000) It seems I've temporary fixed it with: # touch /etc/ld.so.nohwcap From here: http://saintaardvarkthecarpeted.com/blog/archive/2005/08/_etc_ld_so_nohwcap.html

  Read the article

• How do i enable deflate on apache2? debian

  - by acidzombie24

  I looked at the other answers and those solutions did not help. I am completely confused how to do this. I know almost nothing about apache nor how to use it and nearly all the article say write this but doesnt tell me where. So far i have done this # a2enmod deflate Module deflate already enabled Then i tried writing this in httpd.conf AddOutputFilterByType DEFLATE text/html text/plain text/xml text/css Then i wrote a longer version which involved deflate.c. After those didnt work i deleted them all and wrote the AddOutputFilterByType line in apache2/sites-enabled/000-default inside of I used this to test http://www.whatsmyip.org/http_compression/ everytime it says no compression. I used another site but i could never compress. Also i restart the server everytime i save a file so what could be the problem and how do i enable this properly?

  Read the article

• Debian package with init.d without autostart

  - by viraptor

  Hi, I'm trying to create a package which contains the init.d file, but doesn't try to start the daemon right after the installation. Currently, I'm using scripts created from the dh_make template. Right after installation, dpkg wants to start the service. I'd like to stop it from doing that - the daemon will be always started / stopped manually.

  Read the article

• Downgrade 'local' packages in Debian/Ubuntu

  - by Matt Joiner

  I recently unticked the "pre-released updates" option in Software Sources on my Ubuntu Lucid 10.04.1 installation. The Ubuntu wiki states the following regarding this source: The proposed updates are updates which are waiting to be moved into the recommended updates queue after some testing. They may never reach recommended or they may be replaced with a more recent update. Roughly 20 installed packages have indeed not made it into recommended updates, and occasionally cause conflicts when I install new software, as related packages of the newer version are unavailable now that I've disabled the source. How can I force a downgrade of all packages for which an earlier version exists in a enabled repository?

  Read the article

• ARM Debian (squeeze) USB driver with mismatch 3.3.3 kernel but /lib/modules/2.6.36

  - by frank

  Hei guys, my sheevaplug embedded server works fine, but when I wanted to use USB, the device gets not attached to /dev/tty/USB0 lsusb shows correctly: Bus 001 Device 002: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port an modprobe usbserial raises: FATAL: Could not load /lib/modules/3.3.3/modules.dep: No such file or directory in the /lib/modules/ Folder there is instead a 2.6.36-Folder uname -r gives 3.3.3 How can I overcome this mismatch? Can I create a symlink? I can't flash this embedded device since it is deployed somewhere, only ssh? Please advise!

  Read the article

• debian 6 losing a large amount of packets

  - by Sc0rian

  I have a rather strange problem. We covered all the obvious hardware related issues (different nic, eth cable and switch) however I cannot seem to stop eth dropping packets. I have 4 servers all exactly the same. driver: e1000e version: 1.2.20-k2 firmware-version: 1.8-0 bus-info: 0000:06:00.0 They are all running the latest kernel(2.6.32-5-amd64). However they do this: RX packets:17073870634 errors:0 dropped:14147208 overruns:0 frame:0 another server: eth0 Link encap:Ethernet HWaddr e0:69:95:05:2f:cb inet addr:10.10.10.86 Bcast:10.10.10.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5455209277 errors:0 dropped:375445 overruns:0 frame:0 TX packets:3666134366 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6688414486673 (6.0 TiB) TX bytes:1611812171539 (1.4 TiB) Interrupt:20 Memory:d0600000-d0620000 eth1 Link encap:Ethernet HWaddr 00:1b:21:b7:7a:ce inet addr:10.10.0.86 Bcast:10.10.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15473695728 errors:0 dropped:5808325 overruns:0 frame:0 TX packets:20112364421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9192378766434 (8.3 TiB) TX bytes:20216368266761 (18.3 TiB) Interrupt:17 Memory:d0280000-d02a0000 A massive amount of dropped packets. I have tried to load on the latest driver, 1.9.5. This did nothing. I'm not sure what else to do.

  Read the article

• Setting up Debian squirrelmail

  - by Muazam

  I'm new to networking. I need to set up a email server and I also need to create an email address. ex. [email protected] I've installed squirrelmail and dovecot. http://www.mydomain.com/squirrelmail/src/login.php Shows a log in screen, but when I try to log in I get this error: Error connecting to IMAP server: 127.0.0.1. 111 : Connection refused I have no experience with squirrelmail and dovecote. Anyone can help me out, I really appreciate it. Thanks!

  Read the article

• Debian Bluetooth headphones not working

  - by cYrus

  Hardware Headphones Bluetooth dongle Maybe not exactly these models. Setup I tried to follow some guides, here's what I've done so far: Install software: sudo apt-get install bluez-utils bluez-alsa Reboot (just to be sure): $ dmesg | grep -i bluetooth [ 20.268212] Bluetooth: Core ver 2.16 [ 20.268230] Bluetooth: HCI device and connection manager initialized [ 20.268233] Bluetooth: HCI socket layer initialized [ 20.268235] Bluetooth: L2CAP socket layer initialized [ 20.268239] Bluetooth: SCO socket layer initialized [ 20.284685] Bluetooth: RFCOMM TTY layer initialized [ 20.284692] Bluetooth: RFCOMM socket layer initialized [ 20.284693] Bluetooth: RFCOMM ver 1.11 [ 20.335375] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 20.335378] Bluetooth: BNEP filters: protocol multicast The deamon is running: $ /etc/init.d/bluetooth status [ ok ] bluetooth is running. Plug the dongle: $ dmesg | tail [...] [23108.352034] usb 5-2: new full-speed USB device number 2 using ohci_hcd [23108.571131] usb 5-2: New USB device found, idVendor=0a12, idProduct=0001 [23108.571136] usb 5-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [23108.629042] usbcore: registered new interface driver btusb Put the headphones in pairing mode, and try scanning: $ hcitool scan Scanning ... Found nothing. What's next? What should I try? I'll update this answer as soon as you provide me hints.

  Read the article

• debian: supress find warnings

  - by ~astro64m

  I need to get rid off "access denied" messages which fills my find output. I've read man find (maybe not too carefully, hit me) and cannot find anything like -s/--silent or -q/--quiet command line key.

  Read the article

• Debian Server wont reboot from script

  - by Littlejon

  I have a script that is run to backup a server via Rsync, after that script is run I want the server to reboot. My script is run as root from the Crontab at 3am in the morning. #!/bin/bash HOST="email" RSYNC_OPTS="-a -v -v --progress --stats --delete" RSYNC_DEST="10.0.0.10::$HOST" BACKUP_LIST="/etc /home /root" TIMESTAMP="/timestamp-bkup-start.chk" TIMESTAMP2="/timestamp-bkup-stop.chk" touch $TIMESTAMP rsync $RSYNC_OPTS $TIMESTAMP $RSYNC_DEST for BACKUP_ITEM in $BACKUP_LIST; do rsync $RSYNC_OPTS $BACKUP_ITEM $RSYNC_DEST done /etc/init.d/zimbra stop sleep 60s rsync $RSYNC_OPTS /opt $RSYNC_DEST touch $TIMESTAMP2 rsync $RSYNC_OPTS $TIMESTAMP2 $RSYNC_DEST echo `date +%Y%m%d%H%M` >> /var/log/reset reboot # $# shows number of args passed # $1 to access first variable #if [ $# -eq 1 ]; then # if [ $1 = "withreboot" ]; then # echo "rebooting..."; # echo `date +%Y%m%d%H%M` >> /var/log/reset # /sbin/reboot # fi #fi I have tried using init 6 rather then reboot. I have tried /sbin/reboot. I also have another basic script that just echos to the reset log and runs reboot without issue. It is just with the script above the server wont restart. If anyone has any theories that would be great as I have run out of idea. Thanks, Jon

  Read the article

• ipv6 with KVM on debian

  - by Eliasdx

  I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

  Read the article

• ProFTPd not in boot: Debian

  - by 50ndr33

  I just configured my new VPS with Apache, PHP, MySQL and ProFTPd. I wanted to install a smtp server, but I was advised to do a apt-get upgrade first. I did this, and I got up a blue screen where I could choose between two alternatives. It said something about GRUB 2 installer. I chose the alternative that was already selected, the topmost. I chose not to update the GRUB2, and use the old one that was installed. Now, ProFTPd doesn't start in boot anymore. I have to /etc/init.d/proftpd start every time. How do I fix this? Should I have chosen to update GRUB2? Should I do apt-get upgrade again and try to do the same GRUB2 installer again?

  Read the article

• ipv6 with KVM on debian

  - by Eliasdx

  I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

  Read the article

• Debian Wheezy, hostapd running but no AP detected by clients

  - by f0o

  I've an TL-WN951N (AR5416+AR5008) using ath9k module running an hostapd and a dhcp for it. So hostapd starts fine: $ hostapd wifi.test Configuration file: wifi.test Using interface int1 with hwaddr f4:ec:38:9b:d4:93 and ssid 'test' hostapd.conf: interface=int1 driver=nl80211 ssid=test channel=1 But nobody seems to find it or being able to see it or connect to it by setting BSSID to 'test'. I'm quite frustrated now, I find 'howto' after 'howto' from people with same chipsets and it always seemed to work out great for them - but not here... iw list even shows up the AP mode being present at the interface... Thanks for your help

  Read the article

• apache/debian squeeze server loading directory listing instead of website

  - by Diego

  when you navigate to mywebsite.com/ you see an apache page showing a folder called mywebsite.com/, clicking there then takes me to mywebsite.com/mywebiste.com which doesn't exist, so wordpress shows me the a 404 error. I'm trying to host a wordpress site at mywebsite.com/ but I think I have some kind of directory listing wrong somewhere, though I'm pretty sure I've set up my /etc/apache2/sites-available/mywebsite.com correctly: <VirtualHost *:80> ServerName mywebsite.com ServerAdmin [email protected] DocumentRoot /var/www/mywebsite.com/ <Directory /> Options FollowSymLinks AllowOverride All </Directory> ErrorLog /var/log/apache2/error.log CustomLog /var/log/apache2/access.log combined LogLevel warn </VirtualHost>

  Read the article

• not able to install g++ and gcc on debian

  - by austin powers

  Hi , I want to use directadmin as my web control panel and it needs several packages like g++ , gcc and etc... as usuall I started to type apt-get install g++ and there problems start : dependecy error... then I tried to apt-get -f install and I got this error (Reading database ... 15140 files and directories currently installed.) Removing libc6-xen ... ldconfig: /etc/ld.so.conf.d/libc6-xen.conf:6: hwcap index 0 already defined as nosegneg dpkg: error processing libc6-xen (--remove): subprocess post-removal script returned error exit status 1 Errors were encountered while processing: libc6-xen E: Sub-process /usr/bin/dpkg returned an error code (1) what shoud I do? I want to install g++ and all of its dependencies due to using of directadmin I need it. regards.

  Read the article

• How to determine where debian package was sourced

  - by user169309

  How would I trace out which archive(s) in the sources.list a given installed deb package was or (could be) sourced from? I understand that the same package may be indexed by multiple archives. Does "aptitude" log any of this type of information when its installing packages? My aim is to pare down my current sources.list to the minimum set of archives needed to maintain the current set of installed packages.

  Read the article

• sudo suddenly stopped working on debian

  - by chovy

  I've been using 'sudo ' since I setup my server about a week ago. It suddently stopped working with no explanation. I am in 'sudo' group. So there should be no config change required to /etc/sudoers $ sudo apt-get install tsocks [sudo] password for me: me is not in the sudoers file. root@host:/etc# groups me me : me sudo The only thing it could possibly be related to was I added the following line to sshd_config: PermitRootLogin without-password But I have since changed that back to PermitRootLogin yes Permission on file is 400: ls -l /etc/sudoers -r--r----- 1 root root 491 Sep 28 21:52 /etc/sudoers No idea why it stopped working, or how to fix it.

  Read the article

• Locale misconfig. Debian

  - by JakeTheFish

  perl -e 'print "Hello\n";' perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LC_CTYPE = "UTF-8", LANG = "en_US.UTF-8" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). Hello I'v tried to do export LC_ALL=en_US.UTF-8 export LANGUAGE=en_US.UTF-8 And it workis, till I log out. Is there any permanent solution?

  Read the article

< Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >