Search Results

Search found 822 results on 33 pages for 'jawz 74'.

Page 19/33 | < Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26 | Next Page >

big cpu load on vmware server / linux

- by dezfafara

Hi, I currently using a server 2.x hosting 4 virtual machines on a linux system Today, on my physical server, I saw an enormous load average: this is the "top" of the server, illustrating my 4 virtual guests. top - 11:02:02 up 194 days, 23:09, 5 users, load average: 18.78, 12.05, 13.55 Tasks: 113 total, 4 running, 109 sleeping, 0 stopped, 0 zombie Cpu0 : 71.6%us, 19.0%sy, 0.0%ni, 8.8%id, 0.0%wa, 0.3%hi, 0.3%si, 0.0%st Cpu1 : 74.3%us, 10.4%sy, 0.0%ni, 15.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 72.5%us, 17.6%sy, 0.0%ni, 9.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 79.5%us, 4.6%sy, 0.0%ni, 16.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 8178884k total, 8129980k used, 48904k free, 134904k buffers Swap: 10490436k total, 148k used, 10490288k free, 6129728k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 7312 root 6 -10 1149m 921m 559m R 97 11.5 107947:09 vmware-vmx 6995 root 6 -10 779m 687m 317m R 92 8.6 107374:31 vmware-vmx 6693 root 6 -10 880m 659m 409m S 85 8.3 76947:33 vmware-vmx 12937 root 6 -10 960m 719m 523m S 75 9.0 67219:49 vmware-vmx In bold are the cpu usage for my 4 virtuals guests These guests are running on a linux system, and the appropriate process are usually 5% - 15% of cpu I don't understang why , since a few days I have this big problem. This is the "top" on a virtual guest which is at 95% of cpu load top - 11:23:15 up 194 days, 23:13, 4 users, load average: 0.25, 0.47, 0.59 Tasks: 92 total, 2 running, 90 sleeping, 0 stopped, 0 zombie Cpu(s): 1.4%us, 7.7%sy, 0.0%ni, 90.5%id, 0.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 382296k total, 369732k used, 12564k free, 145156k buffers Swap: 979924k total, 13956k used, 965968k free, 86988k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 3691 root 20 0 23948 1148 960 S 13.0 0.3 15339:23 vmware-guestd 3840 root 20 0 19880 584 512 S 7.7 0.2 1729:17 hald-addon-stor This virtual guest state is ok ... If anyone has any ideas .. Thanks

Read the article
Debian x86_64 + Nginx + PHP5-FPM optimization

- by Olal'a

I used to have a VPS (512MB) from Linode and I was running nginx + php5-fpm (which comes with php5.3.3) on Debian Lenny (i686). The total memory usage was about 90-100MB. Now I have another VPS (different hosting company) and I also run nginx + php5-fpm on Debian Lenny (x86_64). The system is 64-bit, so the memory usage is higher now, about 210-230MB, which I think is too much. Here is my php5-fpm.conf: pm = dynamic pm.max_children = 5 pm.start_servers = 2 pm.min_spare_servers = 2 pm.max_spare_servers = 5 pm.max_requests = 300 That's what top command tells me: top - 15:36:58 up 3 days, 16:05, 1 user, load average: 0.00, 0.00, 0.00 Tasks: 209 total, 1 running, 208 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni, 99.9%id, 0.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 532288k total, 469628k used, 62660k free, 28760k buffers Swap: 1048568k total, 408k used, 1048160k free, 210060k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 22806 www-data 20 0 178m 67m 31m S 1 13.1 0:05.02 php5-fpm 8980 mysql 20 0 241m 55m 7384 S 0 10.6 2:42.42 mysqld 22807 www-data 20 0 162m 43m 22m S 0 8.3 0:04.84 php5-fpm 22808 www-data 20 0 160m 41m 23m S 0 8.0 0:04.68 php5-fpm 25102 www-data 20 0 151m 30m 21m S 0 5.9 0:00.80 php5-fpm 10849 root 20 0 44100 8352 1808 S 0 1.6 0:03.16 munin-node 22805 root 20 0 145m 4712 1472 S 0 0.9 0:00.16 php5-fpm 21859 root 20 0 66168 3248 2540 S 1 0.6 0:00.02 sshd 21863 root 20 0 66028 3188 2548 S 0 0.6 0:00.06 sshd 3956 www-data 20 0 31756 3052 928 S 0 0.6 0:06.42 nginx 3954 www-data 20 0 31712 3036 928 S 0 0.6 0:06.74 nginx 3951 www-data 20 0 31712 3008 928 S 0 0.6 0:06.42 nginx 3957 www-data 20 0 31688 2992 928 S 0 0.6 0:06.56 nginx 3950 www-data 20 0 31676 2980 928 S 0 0.6 0:06.72 nginx 3955 www-data 20 0 31552 2896 928 S 0 0.5 0:06.56 nginx 3953 www-data 20 0 31552 2888 928 S 0 0.5 0:06.42 nginx 3952 www-data 20 0 31544 2880 928 S 0 0.5 0:06.60 nginx So, the question is there any way to use less memory? Btw, I have 16 cores and it would be nice to make use of them...

Read the article
Understanding tcptraceroute versus http response

- by kojiro

I'm debugging a web server that has a very high wait time before responding. The server itself is quite fast and has no load, so I strongly suspect a network problem. Basically, I make a web request: wget -O/dev/null http://hostname/ --2013-10-18 11:03:08-- http://hostname/ Resolving hostname... 10.9.211.129 Connecting to hostname|10.9.211.129|:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: ‘/dev/null’ 2013-10-18 11:04:11 (88.0 KB/s) - ‘/dev/null’ saved [13641] So you see it took about a minute to give me the page, but it does give it to me with a 200 response. So I try a tcptraceroute to see what's up: $ sudo tcptraceroute hostname 80 Password: Selected device en2, address 192.168.113.74, port 54699 for outgoing packets Tracing the path to hostname (10.9.211.129) on TCP port 80 (http), 30 hops max 1 192.168.113.1 0.842 ms 2.216 ms 2.130 ms 2 10.141.12.77 0.707 ms 0.767 ms 0.738 ms 3 10.141.12.33 1.227 ms 1.012 ms 1.120 ms 4 10.141.3.107 0.372 ms 0.305 ms 0.368 ms 5 12.112.4.41 6.688 ms 6.514 ms 6.467 ms 6 cr84.phlpa.ip.att.net (12.122.107.214) 19.892 ms 18.814 ms 15.804 ms 7 cr2.phlpa.ip.att.net (12.122.107.117) 17.554 ms 15.693 ms 16.122 ms 8 cr1.wswdc.ip.att.net (12.122.4.54) 15.838 ms 15.353 ms 15.511 ms 9 cr83.wswdc.ip.att.net (12.123.10.110) 17.451 ms 15.183 ms 16.198 ms 10 12.84.5.93 9.982 ms 9.817 ms 9.784 ms 11 12.84.5.94 14.587 ms 14.301 ms 14.238 ms 12 10.141.3.209 13.870 ms 13.845 ms 13.696 ms 13 * * * … 30 * * * I tried it again with 100 hops, just to be sure – the packets never get there. So how is it that the server does respond to requests via http, even after a minute? Shouldn't all requests just die? I'm not sure how to proceed debugging why this server is slow (as opposed to why it responds at all).

Read the article
QMail do not delivery to remote mailboxes for my own domain

- by lorenzo-s

Sorry for the title, I don't know how to sum up this situation. I have a web server at mydomain.com, running qmail for website related mail delivery (i.e. newsletter, sign up confirmation, etc). qmail here is used only to send mails, because I have a fully working Google App Gmail associated with mydomain.com for normal email receiving. qmail runs fine when sending email to remote addresses, for example to [email protected], but fails when sending to [email protected]. I think it's because the server thinks that he have to manage mailboxes for mydomain.com locally, instead of redirect them to Gmail. Here is the /var/log/qmail/current for two email: the first one is sent without problems to example.com, second one fails because it's for mydomain.com: 2012-11-15 15:04:11.551933500 new msg 262580 2012-11-15 15:04:11.551936500 info msg 262580: bytes 5604 from <[email protected]> qp 5185 uid 33 2012-11-15 15:04:11.575910500 starting delivery 316: msg 262580 to remote [email protected] 2012-11-15 15:04:11.575912500 status: local 0/10 remote 1/20 2012-11-15 15:04:12.189828500 delivery 316: success: 74.125.136.27_accepted_message./Remote_host_said:_250_2.0.0_OK_1352991894_j49si13055539eep.9/ 2012-11-15 15:04:12.189830500 status: local 0/10 remote 0/20 2012-11-15 15:04:12.189831500 end msg 262580 2012-11-15 16:49:20.270332500 new msg 262580 2012-11-15 16:49:20.270336500 info msg 262580: bytes 2192 from <[email protected]> qp 5479 uid 33 2012-11-15 16:49:20.315125500 starting delivery 323: msg 262580 to local [email protected] 2012-11-15 16:49:20.315128500 status: local 1/10 remote 0/20 2012-11-15 16:49:20.320855500 delivery 323: failure: Sorry,_no_mailbox_here_by_that_name._(#5.1.1)/ 2012-11-15 16:49:20.320858500 status: local 0/10 remote 0/20 2012-11-15 16:49:20.372911500 bounce msg 262580 qp 5484 2012-11-15 16:49:20.372914500 end msg 262580 As you can see, it says: Sorry,_no_mailbox_here_by_that_name I can't say he's wrong :) How to solve this? How to let Google App Gmail manage incoming email for mydomain.com for messages sent by mydomain.com qmail server?

Read the article
Debian x86_64 + Nginx + PHP5-FPM optimization

- by user55859

I used to have a VPS (512MB) from Linode and I was running nginx + php5-fpm (which comes with php5.3.3) on Debian Lenny (i686). The total memory usage was about 90-100MB. Now I have another VPS (different hosting company) and I also run nginx + php5-fpm on Debian Lenny (x86_64). The system is 64-bit, so the memory usage is higher now, about 210-230MB, which I think is too much. Here is my php5-fpm.conf: pm = dynamic pm.max_children = 5 pm.start_servers = 2 pm.min_spare_servers = 2 pm.max_spare_servers = 5 pm.max_requests = 300 That's what top command tells me: top - 15:36:58 up 3 days, 16:05, 1 user, load average: 0.00, 0.00, 0.00 Tasks: 209 total, 1 running, 208 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni, 99.9%id, 0.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 532288k total, 469628k used, 62660k free, 28760k buffers Swap: 1048568k total, 408k used, 1048160k free, 210060k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 22806 www-data 20 0 178m 67m 31m S 1 13.1 0:05.02 php5-fpm 8980 mysql 20 0 241m 55m 7384 S 0 10.6 2:42.42 mysqld 22807 www-data 20 0 162m 43m 22m S 0 8.3 0:04.84 php5-fpm 22808 www-data 20 0 160m 41m 23m S 0 8.0 0:04.68 php5-fpm 25102 www-data 20 0 151m 30m 21m S 0 5.9 0:00.80 php5-fpm 10849 root 20 0 44100 8352 1808 S 0 1.6 0:03.16 munin-node 22805 root 20 0 145m 4712 1472 S 0 0.9 0:00.16 php5-fpm 21859 root 20 0 66168 3248 2540 S 1 0.6 0:00.02 sshd 21863 root 20 0 66028 3188 2548 S 0 0.6 0:00.06 sshd 3956 www-data 20 0 31756 3052 928 S 0 0.6 0:06.42 nginx 3954 www-data 20 0 31712 3036 928 S 0 0.6 0:06.74 nginx 3951 www-data 20 0 31712 3008 928 S 0 0.6 0:06.42 nginx 3957 www-data 20 0 31688 2992 928 S 0 0.6 0:06.56 nginx 3950 www-data 20 0 31676 2980 928 S 0 0.6 0:06.72 nginx 3955 www-data 20 0 31552 2896 928 S 0 0.5 0:06.56 nginx 3953 www-data 20 0 31552 2888 928 S 0 0.5 0:06.42 nginx 3952 www-data 20 0 31544 2880 928 S 0 0.5 0:06.60 nginx So, the question is there any way to use less memory? Btw, I have 16 cores and it would be nice to make use of them...

Read the article
What are these CPU cache settings? Snoop Filter, ACL prefetch, HW prefetch

- by eater

I was in my BIOS setup turning on VT-x support today and saw these other settings. A little googling indicates that they each seem to turn on some sort of optimization to do with the CPU's L2 cache. They were all turned off by default. The processor in question is an Intel Xeon quad-core 3.4GHz (X5492). My OS is Linux 2.6.35.10-74.fc14.x86_64 #1 SMP Thu Dec 23 16:04:50 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux. I have 4GB of RAM if that matters. Here's what the BIOS manufacturer has to say: Snoop Filter Enabling the snoop filter typically improves performance by reducing snoop traffic on the frontside bus in dual processor configurations. Well I like the sound of improved performance. Why would the BIOS have this off by default? Or by dual processor do they not mean multi-core? Regardless, is there a downside if this is on? ACL Prefetch When enabled, the Adjacent Cache Line Prefetcher fetches both cache lines that comprise a cache line pair when it determines required data is not currently in its cache. When disabled, the processor will only fetch the cache line required by the processor. HW Prefetch Fetches an extra line of data into L2 from external memory. Both of these sound like optimizations that have some drawbacks. What are the reasons to turn them on? What are the reasons to leave them off. Why is the default off?

Read the article
Can't access WordPress blog after host changed IP address of server

- by John

My host changed servers and all websites now have a new IP address. I have the same domain name and I assume the host runs the same nameservers, though my host and domain name provider are different. Notes: I never entered a Name or description under General/Settings for my blog. I left them both blank. That is when I could log into it. The wp-config file, has localhost entered rather than a specific IP. Again this has always been the case and my host never advised otherwise. I can get into cPanel by simply putting the newly advised IP in front of /Cpanel. However, I can not reach the admin panel of my WordPress blog (version 2.8.2). I had been loggin into it via http://xx.xx.xxx.xx/~example/blog/wp-login.php. My host suggested to simply insert the new IP in place of the old one. I still get the error message: 404 Not Found The server can not find the requested page: Apache/2.0.63 (Unix) mod_ssl/2.0.63 OpenSSL/0.9.8e-fips-rhel5 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 PHP/5.2.12 Server at 74.50.108.14 Port 80 I followed some tips on a question on Stack Overflow of a similar nature. I have logged into phpMyAdmin and found the wp-options table and searched for SELECT * FROM `wp_options` WHERE `option_name` IN ('siteurl', 'home') Only option ID 39 came up and the results are: Home has optionvalue http://example.org siteurl has optionvalue http://example.org/blog Both of which appear correct. Is there any part of the MySQL tables where I can change an actual IP address? Or is there something else you can advise?

Read the article
Lion MacBook Pro will not load webpages with DNS just after wake

- by NReilingh

I'm working with a 2011 MacBook Pro running Lion (10.7.2), that after waking from sleep (i.e. opening the lid) takes an inordinately long amount of time (2-3 minutes or more) to get a usable internet connection. Upon waking, the wi-fi icon signifies it is negotiating a network connection, and completes one a few seconds later. At this point, network diagnostics will not show any issues, and everything in Network preferences looks as normal: I'm connected to the proper network, have the right IP address and gateway, and DNS settings are correct. However, any site accessed with a domain name (like http://www.google.com) in Safari will return the "You are not connected to the Internet." error. Accessing a site directly, say, with Google's 74.125.226.212, is successful. Yet, Network Diagnostics will insist that DNS is functioning properly. After a few minutes, the following lines will be printed to the Console log, and regular behavior will be restored. 11/18/11 8:11:31.288 PM airportd: _doAutoJoin: Already associated to “Wireless”. Bailing on auto-join. 11/18/11 8:11:32.000 PM kernel: en1: BSSID changed to 00:25:9c:63:91:bd This behavior occurs only when waking from sleep--not when turning wi-fi on and off. This problem also occurs when using a wired Ethernet connection. As per this thread, I have tried flushing the DNS cache and wiping the wireless network from memory (it's not a protected network). Neither have worked.

Read the article
Corrupted NTFS Drive showing multiple unallocated partitions

- by volting

My external hdd with a single NTFS partition was accidentaly plugged out (kids!)... and is now corrupted. Iv tried running ntfsfix - with no luck - output below.. When I look at the disk under disk management in Windows 7 it shows up as having 5 partitions 2 of which are unallocated - none have drive letters and it is not possible to set any (that option and most others are greyed out) - so I can't run chkdsk /f Iv tried using Minitool partition wizard which was mentioned as a solution to another similar question here. It showed the whole drive as one partition, but as unallocated, and the option -- "Check File System" was greyout. Is there anything else I could try ? Output of fdisk -l Disk /dev/sdb: 1500.3 GB, 1500299395072 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930272256 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytest I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x69205244 This doesn't look like a partition table Probably you selected the wrong device. Device Boot Start End Blocks Id System /dev/sdb1 ? 218129509 1920119918 850995205 72 Unknown /dev/sdb2 ? 729050177 1273024900 271987362 74 Unknown /dev/sdb3 ? 168653938 168653938 0 65 Novell Netware 386 /dev/sdb4 2692939776 2692991410 25817+ 0 Empty Partition table entries are not in disk order Output of ntfsfix me@vaio:/dev$ sudo ntfsfix /dev/sdb Mounting volume... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error FAILED Attempting to correct errors... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error FAILED Failed to startup volume: Input/output error Checking for self-located MFT segment... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument OK ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error Volume is corrupt. You should run chkdsk. Options available with MiniTool: Related questions: How to fix a damaged/corrupted NTFS filesystem/partition without losing the data on it? Repair corrupted NTFS File System

Read the article
Mac dev folder missing, SSH not working

- by SamGoody

A few days ago, SSH stopped working. When I try logging in a get the following message: PTY allocation request failed on channel 0 stdin: is not a tty fatal: unrecognized command '' Connection to 74.52.61.194 closed. Web searches have shown me that there might be something wrong with /dev/std. But my computer lacks a /dev/ drive. There is an Alias to /dev/ [hidden, but I've revealed hidden files to do this search], but when I try to open it I am told that it cannot find the folder it is aliasing. Now, many a web search tells me that without a dev folder, the computer doesn't work, but it does seem to work, except the SSH. Also, are there any tools that can save my SSH preferences so that I don't have to, each time, type out the username@adrees, password, path all of which are long and complex? Not looking for a Filezilla type client, there are many of those. Looking for a command line like putty, that lets me use bash on the remote client. Am on Macbook Pro, latest version of Tiger.

Read the article
Iptables ignoring a rule in the config file

- by Overdeath

I see lot of established connections to my apache server from the ip 188.241.114.22 which eventually causes apache to hang . After I restart the service everything works fine. I tried adding a rule in iptables -A INPUT -s 188.241.114.22 -j DROP but despite that I keep seeing connections from that IP. I'm using centOS and i'm adding the rule like thie: iptables -A INPUT -s 188.241.114.22 -j DROP Right afther that I save it using: service iptables save Here is the output of iptables -L -v ` Chain INPUT (policy ACCEPT 120K packets, 16M bytes) pkts bytes target prot opt in out source destination 0 0 DROP all -- any any lg01.mia02.pccwbtn.net anywhere 0 0 DROP all -- any any c-98-210-5-174.hsd1.ca.comcast.net anywhere 0 0 DROP all -- any any c-98-201-5-174.hsd1.tx.comcast.net anywhere 0 0 DROP all -- any any lg01.mia02.pccwbtn.net anywhere 0 0 DROP all -- any any www.dabacus2.com anywhere 0 0 DROP all -- any any 116.255.163.100 anywhere 0 0 DROP all -- any any 94.23.119.11 anywhere 0 0 DROP all -- any any 164.bajanet.mx anywhere 0 0 DROP all -- any any 173-203-71-136.static.cloud-ips.com anywhere 0 0 DROP all -- any any v1.oxygen.ro anywhere 0 0 DROP all -- any any 74.122.177.12 anywhere 0 0 DROP all -- any any 58.83.227.150 anywhere 0 0 DROP all -- any any v1.oxygen.ro anywhere 0 0 DROP all -- any any v1.oxygen.ro anywhere Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 186K packets, 224M bytes) pkts bytes target prot opt in out source destination `

Read the article
Ubuntu 10.04 network manager issues

- by Shark

I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

Read the article
Slow tracepath on local LAN

- by Simone Falcini

I am on EXSi and I have 2 instances: Ubuntu and CentOS. These are the network configurations Ubuntu eth0 Link encap:Ethernet HWaddr 00:50:56:00:1f:68 inet addr:212.83.153.71 Bcast:212.83.153.71 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76059 errors:0 dropped:26 overruns:0 frame:0 TX packets:7224 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6482760 (6.4 MB) TX bytes:2080684 (2.0 MB) eth1 Link encap:Ethernet HWaddr 00:0c:29:46:5a:f2 inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:252 errors:0 dropped:0 overruns:0 frame:0 TX packets:608 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:42460 (42.4 KB) TX bytes:82474 (82.4 KB) /etc/iptables.conf *nat :PREROUTING ACCEPT [142:12571] :INPUT ACCEPT [5:1076] :OUTPUT ACCEPT [8:496] :POSTROUTING ACCEPT [8:496] -A POSTROUTING -s 192.168.1.0/24 -o eth0 -j MASQUERADE COMMIT *filter :INPUT ACCEPT [2:72] :FORWARD ACCEPT [4:336] :OUTPUT ACCEPT [6:328] -A INPUT -i eth1 -p tcp -j ACCEPT -A INPUT -i eth1 -p udp -j ACCEPT -A INPUT -i eth0 -p tcp --dport ssh -j ACCEPT COMMIT CentOS eth0 Link encap:Ethernet HWaddr 00:0C:29:74:1C:55 inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe74:1c55/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:499 errors:0 dropped:0 overruns:0 frame:0 TX packets:475 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68326 (66.7 KiB) TX bytes:82641 (80.7 KiB) The main problem is that if i execute this command from the CentOS instance ssh 192.168.1.2 it takes more than 20s to connect. It seems like it's routing the connection to the wrong network. What could it be? Thanks!

Read the article
Good HTTP Monitoring tools

- by ffffff

I look for HTTP to work with a Linux system server monitor tool every protocol. I know, and will not there be it in whom or a freeware? When, for example, I dump 80/tcp with a packet monitor to be concrete # tethereal -i ppp0 port 80 -x Capturing on ppp0 1244206390.030474 219.111.xx.xx -> 74.125.xx.xx HTTP GET /search?output=js&num=0&dt=1244206414703&client=pub-3031568651010206&q=Cagliari%20Flight&ad=n3&ie=utf8&oe=utf8&channel=0091594208&adtest=off HTTP/1.1 0000 00 04 02 00 00 00 00 00 00 00 00 00 00 00 08 00 ................ 0010 45 00 01 e5 ee 82 40 00 40 06 d2 b5 db 6f 02 5b E.....@[email protected].[ 0020 4a 7d 4f 93 d4 29 00 50 3e df 4c 63 4b 6b 42 e0 J}O..).P>.LcKkB Such output is provided, but there is too much unnecessary information such as an SYN packet or a header. What I want The IP address of the client and sending out character string(Get; the contents of the POST) Among the output character string of the server only as for the HTML (Content-Type:) I am what is chisel) of a thing of text/html. I can set a filter and am the best if only information wanting can accumulate in the log.

Read the article
Massive number of context switches on ksoftirqd

- by Pace

We have two servers that are grinding to a halt. One is a VM and the other is bare metal. Neither of them are running similar code but they are on the same network. It appears that an incredible number of context switches are arising from ksoftirqd (which is taking up a lot of CPU). vmstat output procs -----------memory---------- ---swap-- -----io---- -system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 1 0 0 605092 182496 2637556 0 0 0 0 4177 519187 8 19 73 0 0 2 0 0 605092 182496 2637556 0 0 0 0 4792 520980 8 19 74 0 0 3 0 0 605092 182496 2637552 0 0 0 0 2137 659640 18 26 56 0 0 ... pidstat output TCK4-BM-06A:~ # pidstat -w -I 5 Linux 2.6.32.12-0.7-default (TCK4-BM-06A) 07/02/2012 _x86_64_ 03:03:01 PM PID cswch/s nvcswch/s Command 03:03:06 PM 1 0.20 0.00 init 03:03:06 PM 4 386666.27 0.00 ksoftirqd/0 03:03:06 PM 6 0.60 0.00 ksoftirqd/1 03:03:06 PM 8 378213.17 0.00 ksoftirqd/2 03:03:06 PM 10 0.20 0.00 ksoftirqd/3 03:03:06 PM 12 0.20 0.00 ksoftirqd/4 03:03:06 PM 26 377115.37 0.00 ksoftirqd/11 03:03:06 PM 27 1.80 0.00 events/0 03:03:06 PM 28 1.00 0.00 events/1 03:03:06 PM 29 1.00 0.00 events/2 03:03:06 PM 30 1.00 0.00 events/3 03:03:06 PM 31 0.80 0.00 events/4 03:03:06 PM 32 0.80 0.00 events/5 ... My initial thought is that, since both are on the same network, something is flooding the network. Is this consistent with the data?

Read the article
Configuring Vmware virtual machines to run under different IPs and PC specs

- by Alex

Right now I'm using a simple VmWare virtual machine with preinstalled Win 7. The IP is assigned automatically (it's the same as main OS IP). Is it possible to create several virtual machines that have different hardware specifications and different IP addresses? Here is what I mean regarding these issues: Specs: Certainly, you can easily change some specifications in the Settings menu (RAM size, HDD size), but what about advanced settings? For example: advanced settings for the Processor: is it AMD (2500+,4000+, etc.. ) or Intel (core 2, Pentium, etc..) Ram - is it Corsair 4 Gb 1333 Mhz or Kingston 2 x 2 Gb 866Mhz or something else? Hdd - Is it Seagate Barracuda 80 gb 5400 Rpm or is it Samsung 500Gb 7200 Rpm or some random SSD? Programs that work under a Virtual Machine shouldn't have a clue if that's a VmWare or not. IPs: Every program that's launched under main OS use the real IP: 93.56.xx.xx All programs that are launched under virtual machine A use IP 1: 74.78.xx.xx All programs that are launched under virtual machine B use IP 2: 84.159.xx.xx I believe that you have to use either VPN or Proxy to solve this problem. The Sum Up: The idea is to create 2-3 independent virtual machines with different hardware specifications and IP addresses. Programs that work under a certain Virtual Machine shouldn't have a clue if that's a VmWare or the real PC. Any ideas/tips or experience regarding configuration will be appreciated!

Read the article
Certain websites redirect to 127.0.0.1. How do I fix this?

- by Dian

Facebook and Youtube in particular. Tried nslookup the address shows as 127.0.0.1. Checked the HOSTS file, it's fine. Ran Malwarebytes' Anti-Malware (didn't find any problems) and SpyBot Search and Destroy (found 1 problem). (Not sure if the Spybot made this improvement) now pinging youtube shows the correct address (74.125.71.91) but the browser still says: Connection to 127.0.0.1 Failed The system returned: (111) Connection refused Tried ipconfig /flushdns but there are no changes. Switched to another user but the results are the same. hosts file: # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. # 127.0.0.1 localhost # ::1 localhost ipconfig all: Connection-specific DNS Suffix: DNS Servers: 10.1.1.30 208.67.220.220

Read the article
Unable to install .NET Framework 3.5 to my XP machine

- by CptanPanic

I have an application that requires .NET 3.5, but I can't install it. The installer quits saying "it has encoutered a problem during setup. If I look at some of the error logs in the tmp directory I see. Error occurred while initializing fusion. It seems that I have 2.0 SP1 installed. Any ideas how I can get it to work? I went through the temp directory and found these references to the error. Any ideas? [04/17/12,18:55:09] Microsoft .NET Framework 2.0a: [2] Error: Installation failed for component Microsoft .NET Framework 2.0a. MSI returned error code 1603 [04/17/12,18:55:27] WapUI: [2] DepCheck indicates Microsoft .NET Framework 2.0a is not installed. 04/19/12 19:08:48 DDSet_Status: Loading fusion.dll using LoadLibraryShim() 04/19/12 19:08:48 DDSet_Error: Error occurred while initializing fusion. Setup could not load fusion with LoadLibraryShim(). Error: 0x80131700 04/19/12 19:08:48 DDSet_Status: Loading fusion.dll using LoadLibraryShim() 04/19/12 19:08:48 DDSet_Error: Error occurred while initializing fusion. Setup could not load fusion with LoadLibraryShim(). Error: 0x80131700 MSI (s) (74!08) [19:08:48:062]: Product: Microsoft .NET Framework 2.0 Service Pack 1 -- Error 25007.Error occurred while initializing fusion. Setup could not load fusion with LoadLibraryShim(). Error: 0x80131700 Error 25007.Error occurred while initializing fusion. Setup could not load fusion with LoadLibraryShim(). Error: 0x80131700

Read the article
Why can't a PC with 2 network cards be accessed by hostname?

- by lewis

I set up PC with 2 network cards, connected to the same LAN. I can connect to this PC (e.g. by remote desktop) only via ip-addresses. Accessing by hostname does not work. Why is this the case? UPDATE: Full environment 1. PC with 2 hardware network adapters. 2. On this PC installed VMWare Workstation. Created 3 VM's, networked by "bridged" network setting in VMWare. 3. In LAN all ip-addresses given from DHCP. 4. Win2k8 on all hosts (both physical and vitrual). As result: 1. PC has 2 ip-address (e.g. 192.168.1.71 and 192.168.1.72). PC available in LAN by ip-addreses, but not avail by hostname. 2. VM's has own ip-addr on each (e.g. 192.168.1.73, *74, *75 etc). They are available from LAN by their ip's, BUT not by their hostnames. How can I access to PC and to VM's by hostname?

Read the article
Packet flooding while configuring a Debian L2TP/IPSec client?

- by Joseph B.

I'm currently at my wits end trying to configure an L2TP over IPSec VPN connection on my Debian using openswan and xl2tp box connecting to a server of unknown configuration. I've managed to successfully establish the connection and everything appears to be working well until I attempt to set the VPN connection as my default route, at which point I see a massive flood of packets simultaneously being transmitted (on the tune of ~1.5 GB in about 2min) until the server drops my connection. Prior to this network traffic on all my interfaces is minimal. According to iftop the majority of this traffic appears to be coming out of port 12, although I can't seem to figure out how to finger a specific process. If I instead just route traffic destined for 74.0.0.0/8 through it I'm able to access Google's servers through the VPN without issue. My xl2tp.conf file is: [lac vpn-nl] lns = example.vpn.com name = myusername pppoptfile = /etc/ppp/options.l2tpd.client My options.l2tpd.client file is: ipcp-accept-local ipcp-accept-remote refuse-eap require-mschap-v2 noccp noauth idle 1800 mtu 1410 mru 1410 usepeerdns lock name myusername password mypassword connect-delay 5000 And my routing table looks like: Destination Gateway Genmask Flags Metric Ref Use Iface 10.5.2.1 * 255.255.255.255 UH 0 0 0 ppp0 10.0.50.0 * 255.255.255.0 U 0 0 0 eth0 10.50.0.0 * 255.255.0.0 U 0 0 0 eth0 10.0.0.0 * 255.255.0.0 U 0 0 0 eth0 192.168.0.0 * 255.255.0.0 U 0 0 0 eth0 loopback * 255.0.0.0 U 0 0 0 lo default * 0.0.0.0 U 0 0 0 ppp0 I'm seeing absolutely nothing in auth.log and syslog during this time and can't seem to find any other log files it might be writing to. Any suggestions would be appreciated!

Read the article
SSH from ubuntu server to Windows 2008 repeatedly asks for password

- by jrizos

I am trying to setup GIT using SSH mode. The central GIT repository is on a NAS device running Windows 2008 server and the user GIT repository is on ubuntu 12.04. When I try to SSH to the windows machine however I am not able to successfully get in. SSH keays are not setup but I think the problem is even before that since I cant get in just by providing the correct password. The output from the SSH command is below. Any help would be appreciated. dba@clpserv01:~$ ssh -v -l administrator clpnas OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Connecting to clpnas [***.***.***.***] port 22. debug1: Connection established. debug1: identity file /home/dba/.ssh/id_rsa type -1 debug1: identity file /home/dba/.ssh/id_rsa-cert type -1 debug1: identity file /home/dba/.ssh/id_dsa type -1 debug1: identity file /home/dba/.ssh/id_dsa-cert type -1 debug1: identity file /home/dba/.ssh/id_ecdsa type -1 debug1: identity file /home/dba/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.5p1 Debian-6+squeeze2 debug1: match: OpenSSH_5.5p1 Debian-6+squeeze2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA bd:37:d1:98:51:2a:d6:b5:f5:c7:98:d8:74:2c:4e:cd debug1: Host 'clpnas' is known and matches the RSA host key. debug1: Found key in /home/dba/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /home/dba/.ssh/id_rsa debug1: Trying private key: /home/dba/.ssh/id_dsa debug1: Trying private key: /home/dba/.ssh/id_ecdsa debug1: Next authentication method: keyboard-interactive Password: debug1: Authentications that can continue: publickey,password,keyboard-interactive Password:

Read the article
Explorer constantly hanging

- by user978122

So I'm running Windows 7 Ultimate (x64) an AMD 8150 on an Asus Crosshair V motherboard with all the latest and greatest patches, and I am experiencing frequent Explorer freezes. I've included the information I've grepped from the Event Viewer below: The program Explorer.EXE version 6.1.7601.17567 stopped interacting with Windows and was closed. To see if more information about the problem is available, check the problem history in the Action Center control panel. Process ID: 13a4 Start Time: 01cdb2968999c6fd Termination Time: 0 Application Path: C:\Windows\Explorer.EXE Report Id: c000ba44-1e8b-11e2-9ae7-000272ddf2b0 - System - Provider [ Name] Application Hang - EventID 1002 [ Qualifiers] 0 Level 2 Task 101 Keywords 0x80000000000000 - TimeCreated [ SystemTime] 2012-10-25T10:08:44.000000000Z EventRecordID 14626 Channel Application Computer RyanMain-PC Security - EventData Explorer.EXE 6.1.7601.17567 13a4 01cdb2968999c6fd 0 C:\Windows\Explorer.EXE c000ba44-1e8b-11e2-9ae7-000272ddf2b0 430072006F00730073002D0074006800720065006100640000000000 -------------------------------------------------------------------------------- Binary data: In Words 0000: 00720043 0073006F 002D0073 00680074 0008: 00650072 00640061 00000000 In Bytes 0000: 43 00 72 00 6F 00 73 00 C.r.o.s. 0008: 73 00 2D 00 74 00 68 00 s.-.t.h. 0010: 72 00 65 00 61 00 64 00 r.e.a.d. 0018: 00 00 00 00 .... Any idea what "Cross-thread" here means?

Read the article
How to use the outcome of a formula as the value for Vlookup or another IF formula

- by Steven

Ok I will try to explain my issue effectively. I am making a GPA sheet in which the value out of 100 is computer in to a GPA value and then in to a letter. In cell N5 i have the value of all their grades (formula: =H3+H4+H5) Now in cell (j6) I have a formula which is giving them a number depending on the value calculated in N5 (Formula: =IF(AND(N5>=60,N5<=63.999),"2.0",IF(AND(N5>=64,N5<=66.999),"2.25",IF(AND(N5>=67,N5<=69.999),"2.4",IF(AND(N5>=70,N5<=73.999),"2.5",IF(AND(N5>=74,N5<=76.999),"2.75",IF(AND(N5>=77,N5<=79.999),"2.9",IF(AND(N5>=80,N5<=83.999),"3.0",IF(AND(N5>=84,N5<=86.999),"3.25",IF(AND(N5>=87,N5<=89.999),"3.4",IF(AND(N5>=90,N5<=93.999),"3.50",IF(AND(N5>=94,N5<=96.999),"3.75",IF(AND(N5>=97,N5<=100),"4",IF(AND(N5<=59.999),"0"))))))))))))) Still no problem... as the values I was looking for comes out (example 84.2 shows up as 3.25 as I wanted). However here comes the problem.... I have tried to use the outcome in J6 to do Vlookup or another if formula, however excel does not seem to recognize the value in J6. For example: =VLOOKUP(j6,B3:C15,2,FALSE)... this returns N/A however if I enter =VLOOKUP(3.25,B3:C15,2,FALSE) it gives me what im looking for. It seems that excel will not register the outcome of my formula as a number. What can I do please?

Read the article
Recovering data from an external hard drive

- by CCallaghan

I have a WD Elements 2GB hard drive (formatted NTFS). I accidentally kicked out the USB cable while writing data to the disk, and now I can't access most of the data. Although this was ostensibly my backup drive, there is a great deal of important material on there which was only on there. I realise how idiotic this makes me. (So, formatting is not an option.) Things I've tried/information I've gathered: Windows Explorer will recognise the drive itself. However, it will not access most directories therein (and will sometimes crash when exploring). I can access all of the directories through the command line, but the dir command will often report that it can't read any files in most of the directories. The situation was similar when I hooked it up to an Ubuntu machine: the file explorer crashed, but I could access directories - but not files in those directories - via terminal commands. Several files I tried to copy out either resulted in an I/O error being reported or resulted in the command line crashing. The Disk Management utility on Windows reports a healthy disk formatted as NTFS and not RAW. It also indicates the correct amount of space used up and its capacity (so it seems that the files are not deleted). I've tried to run chkdsk, but that hangs on Step 2 (checking indexes) at 74%. Step 1 reported no bad sectors. I tried Recuva, but that didn't seem to work (stalled at 0% for half an hour). I should also note that the disk doesn't seem to be spinning smoothly; it seems to be chopping back, like it's reading the same sector over and over again. I noticed this after I kicked out the cable. Any help would be greatly appreciated. Update: It would seem the problem has taken a turn for the worse. The external hard drive now shows up on my computer as a local disk and is not mountable by Linux.

Read the article
How to deal with ssh's "WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED!"?

- by Vi.

I often need to login to multiple remote stations that are just placed to the same static IPs for me. SSH complains about changed keys in this case: $ ssh [email protected] @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ ... Offending RSA key in /home/vi/.ssh/known_hosts:70 ... I usually just run vim /home/vi/.ssh/known_hosts +70, dd wq and re-run the SSH command. How to do it simpler? Requirements: The warning should be displayed, and not like this: The authenticity of host '172.1.2.3 (172.1.2.3)' can't be established. It is easy to accept the key change. I expect something like this: $ ssh [email protected] @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ ... The fingerprint for the RSA key sent by the remote host is 82:cd:be:7a:ae:1b:91:2c:23:c1:74:4d:8a:38:10:32. Change the host key in /home/vi/.ssh/known_hosts (yes/no)? yes Warning: Changed host key for '172.1.2.3' (RSA) in the list of known hosts. [email protected]'s password: Simple and differs from usual "The authenticity of host can't be established." message.

Read the article

< Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26 | Next Page >