Search Results

Search found 2093 results on 84 pages for 'logical'.

Page 19/84 | < Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >

• Cannot enable wireless on an Intel WifiLink 1000 on an Lenovo Ideapad z570

  - by Brij

  I am using the ubuntu 11.10 on lenovo ideapad z570. My wireless internet is not working. I have ensure that wireless switch is on. Windows 7, wireless works great.However ubuntu 11.10 is not allowing me to enable wireless connection. I have run the following command and here is the status. sudo lshw -class network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:1c:a4:a4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:42 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: f0:de:f1:64:b6:62 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff Here is rfkill list all output: rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no Note : Windows 7, wireless card property shows that Intel WifiLink 1000 BGN. Could someone help me to fix this issue.

  Read the article

• Cannot make Wi-Fi hotspot

  - by Junaid

  I want to make my laptop as wi-fi hotspot. To do so, I pressed button Settings-Network-Wireless-Use as Hotspot.. Then it creates a wireless network connection 'Hostspot' and connects. But it gets disconnected just after making connection. Here is my network hardware info: sudo lshw -C network *-network description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:d9200000-d9201fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=192.168.1.4 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:45 ioport:2000(size=256) memory:d5010000-d5010fff memory:d5000000-d500ffff memory:d5020000-d502ffff My machine is running on Ubuntu 11.10 Can anybody help in it? Thanks

  Read the article

• Advanced reporting in Oracle Service Bus

  - by [email protected]

  v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 21 false false false FR-BE X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tableau Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Reporting in OSB is useful, it allows you to audit message going through OSB. The service bus console allows you to view the content that you reported. To report data you simply use the Report action in your proxy. The action itself is rather straightforward. You specify the content to report ($body for example), an optional key for easier search (for example the id of the record) and that's it. Sometimes though, what you want to is a bit more complicated. I recently had a case where the key was built from the message type (XML) and the id of the message. Seems quite simple but the id could be any element anywhere in the message depending on its type. This could be handled by 'if' statement but adding new cases would mean changing the proxy service and if you have lots of message types this can get boring so I wanted the solution to be as dynamic as possible (read "just change a configuration file and that's it"). The following entry details how you can make this dynamic in your proxy by using XQuery/XSLT.   First step the XQuery We're going to use an XQuery to make the mapping between the XML message type and the location of the identifier in it. We assume here that the message type is the first node of the input XML and use a rather simple Xpath to find the identifier.  The XQuery looks like this for two messages : <reportmapping>                 <row>                                <logical>messageType1</logical>                                <type>MT1</type>                                <reportingreferencelocation>//customID</reportingreferencelocation>                 </row>                 <row>                                <logical>messageType2</logical>                                <type>MT2</type>                                <reportingreferencelocation>//theOtherIDLocation</reportingreferencelocation>                 </row>   </reportmapping>   Second step the XSLT To get the identifier value of the dynamic path, we're going to use an XSLT transformation. This XSLT takes an XML parameter as input which contains our xpath (coming from the previous XQuery). The XSLT looks like this : <xsl:stylesheet version="1.0" xmlns:xsl="http://www.w3.org/1999/XSL/Transform" xmlns:xalan="http://xml.apache.org/xalan">               <xsl:param name="PathToNode"/>               <xsl:template match="/">                             <IDVALUE>                                           <xsl:value-of select="xalan:evaluate($PathToNode/reportingreferencelocation)"/>                             </ IDVALUE >               </xsl:template> </xsl:stylesheet> (note the use of a xalan function here. Xalan is the XSLT processor used in weblogic server)   Last step, the proxy service We're now going to wire everything in the proxy service. First we assign the XQuery to a variable. We then get the entry in the XQuery corresponding to the record we're treating. We're then extracting the id of the message using the XSLT transformation Final assign is to built the final variable that will be used as the reporting key. The report action is then called with this variable. Everything is setup. We're now ready to test.   Testing the solution Using the test console, we're sending our first XML ... <messageType1>                 <sender>test console 1</sender>                 <customID>ID12345</customID >                 <content>                                 <field1>value of field 1</field1>                 </content> </messageType1>   ... and a second one of another supported type <messageType2>                 <header>                                 <theOtherIDLocation >ID67890</theOtherIDLocation >                 </header> <body>                                <data>Test data</data>                 </body> </messageType2>   Reporting result is :  Conclusion Report is done as expected. Now if a new message type must be supported we only have to modify the XQuery and nothing at the proxy service level.   Sample project attached to this entry.sbconfig-dynamicReport.jar  

  Read the article

• Gnome-Network-Manager Config File Migration

  - by Jorge

  I think I have an issue with gnome-network-manager, I used to have a lot of connections configured, Wireless, Wired and VPN. After upgrading to 12.04 (from 11.10) I lost every configuration. I realized that the configs that used to be saved in $HOME/.gconf/system/networking/connections now are being saved in /etc/NetworkManager/system-connections/. I don't know how to migrate my settings to the new config file format Can anybody help me? jorge@thinky:~$ sudo lshw -C network *-network description: Ethernet interface product: 82566MM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:1f:e2:14:5a:9b capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k firmware=0.3-0 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:fe000000-fe01ffff memory:fe025000-fe025fff ioport:1840(size=32) *-network description: Wireless interface product: PRO/Wireless 4965 AG or AGN [Kedron] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 61 serial: 00:21:5c:32:c2:e5 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwl4965 driverversion=3.2.0-23-generic-pae firmware=228.61.2.24 ip=192.168.2.103 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:df3fe000-df3fffff jorge@thinky:~$ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04 LTS Release: 12.04 Codename: precise jorge@thinky:~$ uname -a Linux thinky 3.2.0-23-generic-pae #36-Ubuntu SMP Tue Apr 10 22:19:09 UTC 2012 i686 i686 i386 GNU/Linux jorge@thinky:~$ dpkg -l | grep -i firm ii linux-firmware 1.79 Firmware for Linux kernel drivers

  Read the article

• Missing Operating System after trying to upgrade to Ubuntu 11

  - by Mauricio

  there! After trying to upgrade from Ubuntu 10.04 to 11, the upgrading process stopped when running and then I got an "out of disk, grub rescue" message when booting. After running Boot Repair, I got this results. Now I get "Missing Operating System" whent trying to boot. Bellow I show some results from some commands I gather from help foruns, but I still reached no solution. Could you please help me? Any enlightment will be very helpful! Disk Utility says "Disk has a few bad sectors". When trying to run the Self-test I get "FAILED (Read)" Here we have what Gparted says about the /dev/sda1 partition (ext4): Flags: boot Status: not mounted Warning: e2label: Attempt to read block from filesystem resulted in short read while trying to open /dev/sda1Couldn`t find valid filesystem superblockUnable to read the contents of this filesystem! From sudo fdisk -lI got: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectorsUnits = sectors of 1 * 512 = 512 bytesSector size (logical/physical): 512 bytes / 512 bytesI/O size (minimum/optimal): 512 bytes / 512 bytesDisk identifier: 0x000e0596 Device Boot Start End Blocks Id System/dev/sda1 * 2048 607428607 303713280 83 Linux/dev/sda2 607430654 625141759 8855553 5 Extended/dev/sda5 607430656 625141759 8855552 82 Linux swap / SolarisDisk /dev/sdb: 320.1 GB, 320072933376 bytes255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectorsUnits = sectors of 1 * 512 = 512 bytesSector size (logical/physical): 512 bytes / 512 bytesI/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000c3c41 Device Boot Start End Blocks Id System /dev/sdb1 * 63 625137344 312568641 c W95 FAT32 (LBA) " and fromsudo fdisk /dev/sda1I got fdisk: unable to read /dev/sda1: Inappropriate ioctl for device` From sudo mount /dev/sda1 /mntI got: mount: wrong fs type, bad option, bad superblock on /dev/sda1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so From sudo update-grubI got: error: cannot read from `/dev/sda'. /usr/sbin/grub-probe: error: cannot find a device for / (is /dev mounted?).

  Read the article

• Missing Wireless access point

  - by nvcnvn

  I have an: Ubuntu 12.04 with proprietary Boardcom STA Wireless driver installed BCM43224 802.11a/b/g/n wireless card TP-LINK TD-W8101G 54Mbps Wireless ADSL2+ Modem Router Yesterday before I went to sleep, I still connect to my wireless access point, this morning when I start my laptop I don't see it in the list - there are some neighbors listed but not mine. The WLAN is green, with my old Nokia E72, I still see my access point with 100% signal. I have tried to restart my laptop and turn the firmware off/on by the switch but no help. I have read the WirelessTroubleShootingGuide but I can do anything. Here is some of my card info: *-network description: Wireless interface product: BCM43224 802.11a/b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: c0:cb:38:06:5d:53 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11abgn resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 03 serial: f0:4d:a2:42:ab:e4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.1.3 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:5000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff memory:f0420000-f043ffff

  Read the article

• Ubuntu installation does not recognize drive partitioning

  - by Woltan

  I have a 1TB drive and installed Windows 7 on a 128GB partition. When I now try to install Ubuntu 11.04 it does not recognize the Windows partition but offers the complete 1TB drive to install Ubuntu on instead. It displays: However, in the Ubuntu Disk Utility the Windows partitions are recognized. What do I need to do in order for Ubuntu to recognize the Windows 7 partition and install Ubuntu as a dual boot? Response to comments The following commands were executed and the results are shown below: fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x34a38165 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 16318 130969600 7 HPFS/NTFS Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x14a714a6 Device Boot Start End Blocks Id System /dev/sdb1 1 60801 488384001 83 Linux parted -l Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: /dev/sr0: unrecognised disk label

  Read the article

• How to mount an external HDD?

  - by Slash

  I have Ubuntu Linux 12.04 version the latest right now.I want to mount an external HDD NTFS 1TB.I have followed many guides but still no success.The error I'm getting is this: Failed to read last sector (1953523119): Invalid argument HINTS: Either the volume is a RAID/LDM but it wasn't setup yet, or it was not setup correctly (e.g. by not using mdadm --build ...), or a wrong device is tried to be mounted, or the partition table is corrupt (partition is smaller than NTFS), or the NTFS boot sector is corrupt (NTFS size is not valid). Failed to mount '/dev/sdb1': Invalid argument The device '/dev/sdb1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? Using Storage Device MAnager i get this error:Error mounting: mount exited with exit code 1: helper failed with: mount: only root can mount /dev/sdb1 on /media/Skliros_Diskos {external disk name} When I use sudo fdisk -l, this is the output: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e0bc6 Device Boot Start End Blocks Id System /dev/sda1 * 2048 618854399 309426176 83 Linux /dev/sda2 618856446 625141759 3142657 5 Extended /dev/sda5 618856448 625141759 3142656 82 Linux swap / Solaris Disk /dev/sdb: 1000.2 GB, 1000202043392 bytes 255 heads, 63 sectors/track, 121600 cylinders, total 1953519616 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002093a Device Boot Start End Blocks Id System /dev/sdb1 2048 1953525167 976761560 7 HPFS/NTFS/exFAT

  Read the article

• two possible wifi devices competing, one is hard blocked - unable to connect wireless

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff contents of /var/lib/NetworkManager/NetworkManager.state [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• My Android phone isn't being detected by Ubuntu

  - by Lara

  This is what I've got from terminal, looks like it can see the phone as a USB device just fine but isn't showing up under fdisk so I can't mount it. It automounts just fine in my VMWare Windows. And Internet tethering works fine while under Linux (haven't tried under Windows). Here's lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 019: ID 04d9:1135 Holtek Semiconductor, Inc. Bus 001 Device 003: ID 05ca:18c0 Ricoh Co., Ltd Bus 001 Device 004: ID 0489:e00f Foxconn / Hon Hai Foxconn T77H114 BCM2070 [Single-Chip Bluetooth 2.1 + EDR Adapter] Bus 003 Device 010: ID 04e8:6860 Samsung Electronics Co., Ltd Bus 002 Device 012: ID 046d:c315 Logitech, Inc. Classic New Touch Keyboard And here's sudo fdisk -l: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0001ff06 Device Boot Start End Blocks Id System /dev/sda1 2048 681845797 340921875 7 HPFS/NTFS/exFAT /dev/sda2 * 681846784 845686783 81920000 83 Linux /dev/sda3 845686784 968566783 61440000 7 HPFS/NTFS/exFAT /dev/sda4 968568830 972475081 1953126 5 Extended /dev/sda5 968568832 972475081 1953125 82 Linux swap / Solaris Disk /dev/mapper/cryptswap1: 2000 MB, 2000000000 bytes 255 heads, 63 sectors/track, 243 cylinders, total 3906250 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xbe4c2ec7 Disk /dev/mapper/cryptswap1 doesn't contain a valid partition table

  Read the article

• two possible wifi devices competing, one is hard blocked

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• Windows 7 disappeared in list of Grub while loading

  - by Riyad A.

  Installed Ubuntu 12.04 alongside the Windows 7 two weeks ago. Initially haven't any issues with that. day ago installed updates on Ubuntu and after restarting the system found the absence of Win7 in Grub list. Before the HDD has been partitioned on two volumes Disk C and Work Disk(don't remember the name). When doing the fdisk -l: Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xa93031e0 Device Boot Start End Blocks Id System /dev/sda1 * 2048 408833842 204415897+ 7 HPFS/NTFS/exFAT /dev/sda2 488386560 976773119 244193280 7 HPFS/NTFS/exFAT /dev/sda3 408834046 488386559 39776257 5 Extended Partition 3 does not start on physical sector boundary. /dev/sda5 408834048 484421631 37793792 83 Linux /dev/sda6 484423680 488386559 1981440 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/mmcblk0: 3965 MB, 3965190144 bytes 49 heads, 48 sectors/track, 3292 cylinders, total 7744512 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/mmcblk0p1 8192 7744511 3868160 b W95 FAT32 When sudo mount /dev/sda ~/1 -o offset [488386560*512] - opens and mounts WORK disk. Need help: how to See and mount disk C. how to see and adjust the Grub to appear both systems in Grub menu when loading?

  Read the article

• wifi not working hp dv4

  - by Blaze

  i get this output for sudo lshw -C network : *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 06 serial: 3c:4a:92:cd:63:98 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network DISABLED description: Wireless interface product: RT5390 [802.11 b/g/n 1T1R G-band PCI Express Single Chip] vendor: Ralink corp. physical id: 0 bus info: pci@0000:0a:00.0 logical name: wlan0 version: 00 serial: 90:00:4e:82:3c:5b width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.0.0-17-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c2500000-c250ffff i cant enable the wifi using the fn+f12 key.. its just stuck. In windows 7 it gets enabled when i press the same keys. but this happens after it gets booted up... i just want to use the wifi in anyway possible. can anybody help?

  Read the article

• Direct IO enhancements in OVM Server for SPARC 2.2(a.k.a LDoms2.2)

  - by user12611315

  The Direct I/O feature has been available for LDoms customers since LDoms2.0. Apart from the latest SR-IOV feature in LDoms2.2, it is worth noting a few enhancements to the Direct I/O feature. These are: Support for Metis-Q and Metis-E cards. These cards are highly requested for support and are worth mentioning because they are the only combo cards containing both FibreChannel and Ethernet in the same card. With this support, a customer can have both SAN storage and network access with just one card and one PCIe slot assigned to a logical domain. This reduces cost and helps when there are less number of slots in a given platform. The following are the part numbers for these cards. I have tried to put the platforms on which each card is supported, but this information can get quickly outdated. The accurate information can be found at the Support Document.  Card Name  Part Number  Platforms Metis-Q: StorageTek Dual 8Gb Fibre Channel Dual GbE ExpressModule HBA, QLogic SG-XPCIEFCGBE-Q8-N  SPARC T3-4, T4-4 Metis-E: StorageTek Dual 8Gb Fibre Chanel Dual GbE ExpressModule HBA, Emulex SG-XPCIEFCGBE-E8-N SPARC T3-4, T4-4  Additional cards added to the portfolio of supported cards. This is mainly Powerville based Ethernet cards, the part numbers for these cards as below:  Part Number  Description  7100477 Sun Quad Port GbE PCI Express 2.0 Low Profile Adapter, UTP  7100481 Sun Dual Port GbE PCI Express 2.0 Low Profile Adapter, MMF  7100483 Sun Quad Port GbE PCI Express 2.0 ExpressModule, UTP  7110486 Sun Quad Port GbE PCI Express 2.0 ExpressModule, MMF    Note:  Direct IO feature has a hard dependency on the Root domain(PCIe bus owner, here Primary domain). That is, rebooting the Root domain for any reason may impact the logical domains having PCIe slots assigned with Direct IO feature. So rebooting a root domain need to be carefully managed. Also apply the failure-policy settings as described in the admin guide and release notes to deal with unexpected cases.

  Read the article

• Can't access external hard drives or thumb drives

  - by calden

  I am not a complete linux noob but I don't know a lot either and would greatly appreciate some help with this. I just installed Ubuntu 10.10 onto my laptop. Everything is working great however USB devices such as thumb drives and external hard drives wont show up. I have been looking around a bit and when I run sudo fdisk -l it displays this: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00065684 Device Boot Start End Blocks Id System /dev/sda1 * 1 29255 234983424 83 Linux /dev/sda2 29255 30402 9212929 5 Extended /dev/sda5 29255 30402 9212928 82 Linux swap / Solaris Disk /dev/sdb: 16.0 GB, 16026435072 bytes 64 heads, 32 sectors/track, 15283 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000df90d Device Boot Start End Blocks Id System /dev/sdb1 * 1 15283 15649776 7 HPFS/NTFS It does seem to display my 16 gig thumb drive but other then seeing it here I cant access it to read and write files to it. It does the same with my external hard drive. I know those devices work as I have tried them on my other computer and they are working fine. Also this is what is in fstab if this will help anybody help me: proc /proc proc nodev,noexec,nosuid 0 0 /dev/sdb1 / ext4 errors=remount-ro 0 1 /dev/sdb5 none swap sw 0 0 Thank you very much for the help everyone.

  Read the article

• Ubuntu installer does not show drives

  - by Tanweer Rashid

  I am trying to install Ubuntu 12.04 LTS on my Inspiron laptio, but the installer does not show any drives. My system has a 1TB SATA drive and a 32GB SSD. As far as I can figure, the boot files are kept on the SSD for fast startup (for Windows). During Win7 installation, I had to manually load drivers for RAID controller to see all available drives. Running fdisk -l from the live CD shows the following: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x234b4782 Device Boot Start End Blocks Id System /dev/sda1 63 80324 40131 de Dell Utility /dev/sda2 * 81920 41627647 20772864 7 HPFS/NTFS/exFAT /dev/sda3 41627648 357019647 157696000 7 HPFS/NTFS/exFAT /dev/sda4 357019648 1953517567 798248960 f W95 Ext'd (LBA) /dev/sda5 672415744 1312966655 320275456 7 HPFS/NTFS/exFAT /dev/sda6 1312968704 1953517567 320274432 7 HPFS/NTFS/exFAT Disk /dev/sdb: 32.0 GB, 32017047552 bytes 255 heads, 63 sectors/track, 3892 cylinders, total 62533296 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x234b474b Device Boot Start End Blocks Id System /dev/sdb1 2048 16775167 8386560 84 OS/2 hidden C: drive ubuntu@ubuntu:~$ In the Ubuntu installer, I can only choose /dev/sdb for "Device for boot loader installation", and sdb doesn't show any drives. I cannot select /dev/sda. Any ideas anyone? Thanks.

  Read the article

• Ubuntu 13.04 to 13.10: Filesystem check or mount failed

  - by SamHuckaby

  I attempted to upgrade from Ubuntu 13.04 to 13.10 today, and mid upgrade the system started flaking out, and eventually locked up entirely. I was forced to restart the computer, and am now unable to get the computer to boot up at all. When I boot currently, it takes me to the GRUB menu, and I can choose to boot normally, or boot in an older version. I have tried several things, which I list below, but no matter what, when I try to finish booting into Ubuntu, I receive the following error: Filesystem check or mount failed. A maintenance shell will now be started. CONTROL-D will terminate this shell and continue booting after re-trying filesystems. Any further errors will be ignored root@ubuntu-computername:~# I have fun fsck -f and everything appears correct, no errors are reported. and it passes all 5 checks. If I run fdisk -l then I get the following information: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes Disk identifier: 0x00010824 Device Boot Start End Blocks Id System /dev/sda1 * 2048 608456703 304227328 83 Linux /dev/sda2 608458750 625141759 8341505 5 Extended Partition 2 does not start on physical sector boundary. /dev/sda5 608458752 625141759 8341504 82 Linux swap / Solaris Disk /dev/sdb: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0fb4b7e8 Device Boot Start End Blocks Id System /dev/sdb1 8192 625139711 312565760 7 HPFS/NTFS/exFAT I am considering just installing a new OS on the other disk, that currently has nothing on it, and then just attempting to scrape my data off the old disk (thankfully I didn't encrypt the files). Really my question is this: Can I salvage this Ubuntu install, or should I give up and just reinstall?

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• solve a partition misalignment?

  - by learner

  I have a new Dell XPS laptop which had Windows 7 installed in it. It also had a default extra partition for "Dell Utility". I installed Ubuntu in it on an Extended Partition along with windows and specified the logical partitions myself (for /,/home and swap). Now when I open Disk Utility , it shows this "Partition misaligned by 512 bytes" error for the Dell Utility partition and "Partition misaligned by 1024 bytes" for the entire Extended partition where Ubuntu is installed. Deleting the extended partition and re-installing Ubuntu may solve the problem of misalignment in the extended partition. But how about the Dell Utility partition? If I re-install Windows 7 Dell Utility wouldn't be a part of the re-install. So that may not solve it either. How do I fix this? Note: The extended partition I made contains an NTFS logical partition for holding data accessible by both OSes(basically a personal data partition). EDIT: I deleted all my Ubuntu partitions and re-installed Ubuntu like before,this time making them partitions with GParted via LiveCD. Now the only problem is that there is a misalignment in the Dell Utility partition. The other misalignment got fixed. Now how do I get rid of that issue?

  Read the article

• wireless is disabled by hardware lenovo 3000g430

  - by sudheer

  sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

  Read the article

• SD Card only mounted after a reboot

  - by hattenn

  I have a Kingston 2GB MicroSD and I plug it in via an inconix MicroSD Adapter to the internal card reader of my Samsung N210 Netbook with Ubuntu 10.10, but it doesn't show up. Only if I reboot the system when the card's plugged in it shows up. Why does it need a reboot for mounting? sudo fdisk -l gives the output below. But I can only see the drive when I reboot the computer while the card's plugged. Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9a5a7990 Device Boot Start End Blocks Id System /dev/sda1 1 1959 15728640 27 Unknown Partition 1 does not end on cylinder boundary. /dev/sda2 * 1959 1972 102400 7 HPFS/NTFS /dev/sda3 1972 18992 136718750 83 Linux /dev/sda4 18992 19458 3738625 5 Extended /dev/sda5 18992 19458 3738624 82 Linux swap / Solaris Disk /dev/sdb: 1973 MB, 1973420032 bytes 60 heads, 59 sectors/track, 1088 cylinders Units = cylinders of 3540 * 512 = 1812480 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1089 1927100+ 6 FAT16

  Read the article

• Ubuntu installation does not recognize drive partinioning

  - by Woltan

  I have a 1TB drive and installed Windows 7 on a 128GB partition. When I now try to install Ubuntu 11.04 it does not recognize the Windows partition but offers the complete 1TB drive to install Ubuntu on instead. It displays: However, in the Ubuntu Disk Utility the Windows partitions are recognized. What do I need to do in order for Ubuntu to recognize the Windows 7 partition and install Ubuntu as a dual boot? Response to comments The following commands were executed and the results are shown below: fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x34a38165 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 16318 130969600 7 HPFS/NTFS Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x14a714a6 Device Boot Start End Blocks Id System /dev/sdb1 1 60801 488384001 83 Linux parted -l Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: /dev/sr0: unrecognised disk label

  Read the article

• Why does Ubuntu 13.10 not detect my Win7 partition?

  - by goutham

  I'm trying to install Ubuntu 13.10 alongside Windows 7 on my DELL INSPIRON 14z 5423 laptop and I'm new to all of this. I'm using the Ubuntu 13.10 64-bit ISO burned onto a CD. The first time I tried to install it, Ubuntu said it did not detect any other OS, which meant I only had 4 options: Erase disk and install Ubuntu (I don't want to do this) Encrypt new Ubuntu. Use LVM. Something else. If I choose the Something else option, it brings me to the partition menu and says that I have 1 disk with free space of (500Gb), but that's not true because I have Windows 7. I restarted the laptop several times and booted the CD again and I got exactly the same as I did previously. How do fix this problem and install Ubuntu alongside Windows 7? After executing "sudo fdisk -l" command in terminal ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xd2b811c5 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 314574847 157184000 7 HPFS/NTFS/exFAT /dev/sda3 314574848 629147647 157286400 7 HPFS/NTFS/exFAT /dev/sda4 629147648 976771071 173811712 7 HPFS/NTFS/exFAT After removing one partition I executed command once again ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xd2b811c5 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 629145599 314469376 7 HPFS/NTFS/exFAT /dev/sda3 629147648 976771071 173811712 7 HPFS/NTFS/exFAT

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• USB flash module giving errors

  - by vshenoy

  Hi, I have a SATA USB flash module which was earlier running a 2.4 linux kernel (2.4.36.6) and on which now I am trying to install ubuntu server 10.04.1 LTS. I have two such USB flash modules and on one of them the installation process itself giving these errors: sd 4:0:0:0 [sda] Device not ready sd 4:0:0:0 [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sd 4:0:0:0 [sda] Sense Key : Not Ready [current] sd 4:0:0:0 [sda] Add. Sense: Medium not present sd 4:0:0:0 [sda] CDB: Write(10): 2a 00 00 05 48 02 00 00 04 00 end_request: I/O error, dev sda, sector 46114 usb 1-1: reset high speed USB device using ehci_hcd and address 2 Buffer I/O error on device sda1, logical block 172033 lost page write due to I/O error on sda1 Buffer I/O error on device sda1, logical block 172034 lost page write due to I/O error on sda1 on the other the installation is successful, but after a day or two of running the machine hangs because of kernel spewing these messages: Remounting filesystem read-only EXT2-fs error (device sda1): read_block_bitmap: Cannot read block [bitmap - block_group = 105, block_bitmap = 860161] EXT2-fs error (device sda1): ext2_get_inode: unable to read inode block - inode=13083, block=24683 ext2_free_inode: bit already cleared for inode 83966 and the machine needs to be hard rebooted. On both the systems SCSI emulation with usb_storage driver is being used to detect the module. Here is the output of /proc/scsi/scsi on 2.4: # cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 02 and on 2.6: # cat /proc/scsi/scsi Attached devices: Host: scsi6 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 00 i.e. only 'ANSI SCSI revision:' is shown as different, although I am not sure if this can cause any problem. Really appreciate if someone can point as to how to debug this issue or any mailing list where I can further ask questions about this.

  Read the article

< Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >