Search Results

Search found 1116 results on 45 pages for 'nic dk'.

Page 19/45 | < Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >

• Is bonding mode=5 a solution against MAC flapping?

  - by Yuri

  There is two are interconnected Cisco WS-2950T. By the one GBIC port on first switch connected a first NIC of bonding interface, and by the one GBIC port on second switch connected a second NIC of bonding interface. Of course the both switches sees the bonding MAC-address only on one interface (eg it is GBIC on first switch) and all incoming traffic for bonding interface passes through this GBIC. But in "mode=5" all outgoing traffic are distributed between the all interfaces that make bond. In this case, the packets will be dropped from the second switch and anyway will going through the first switch? Or the division will be working?

  Read the article

• NLB 2 Windows Server 2003 Servers

  - by Paul Hinett

  I need to configure windows NLB on 2 dedicated servers I have. My main machine has been running for some time, with several domain names pointing to the servers primary IP address. Both servers have 2 NIC's installed, and both have several secondary public IP addresses available if needed? What IP address would I use for the cluster IP, does this IP need to be added to the IP list of both public NIC's ip address list? What IP addresses do I use for the host's dedicated IP? Please help, this is driving me nuts...i've taken down the server twice on accident today! Thank you in advance!

  Read the article

• How can I tell which interface my Supemicro IPMI is piggybacking on?

  - by lorin

  I've used IPMI before, but only on servers where the IPMI interface had a dedicated ethernet port. I've got an Ubuntu 10.04 server with two ethernet cards, which is supposed to have an IPMI interface on it (the motherboard is a Supermicro H8DMR-I2). From what I understand, the IPMI interface is piggybacking on one of the two NICs. Is there any way I can tell which NIC the IPMI interface is piggybacking on? Using ipmitool I've tried to set the IP address on the IPMI interface for the subnet for eth0, and then the subnet for eth1, and it's never reachable. (Can you even reach an IPMI interface from the same NIC it's piggybacking off of, or do you need to try connecting from a different machine on the network?) Also, is there anything special I need to do to enable it? I can access the IPMI interface locally using "ipmitool".

  Read the article

• Would firewire networking be better than 100Megabit ethernet?

  - by Josh

  My office network has a fully switched 1000Megabit ethernet network. I have an Apple iMac with a Gigabit NIC and FireWire, and a Compaq laptop with a 100Megabit NIC and a 4-pin FireWire interface. Accessing my office's shared drives using my laptop is (obviously) much loswer using my laptop than my iMac. Would I see a noticeible performance boost if I enabled Internet Connection Sharing on my iMac and shared the private ethernet network from my iMac with my laptop over FireWire? FireWire is 480Mbit/sec, right? So would I see roughly 4x speed improvement with such a setup?

  Read the article

• dell poweredge 860 always pxe boot

  - by Berto

  Hi, We bought a dell poweredge 860, and installed windows server 2008 std. So far so good. Now everytime the server reboots, it try's the pxe boot, and hangs on "cant find pxe bootable, press f1 to continue or f2 to setup". Now, i tried all the settings in the bios (it's the latest - A05), i have the nic active without pxe (i also tried with the nic off)... well, i tried everyting off and on the bios and it still goes to pxe booting. I have one sata drive, that is boot's after the f1. I would like to keep the system updated, but i can't because of the reboot, can someone point me to some direction? Can i give any more information of the server? If yes, what do you want? It has been a week on google trying to figure out this one. Thx

  Read the article

• ESXi and Networking Devices

  - by EsxiUser

  I have two intel pro 1000 pt nics. One quad and one dual port. I want to assign all nic ports to a VM. I enabled PCI passthrough on all devices but ESXi will only allow me to add two nic ports until it tells me the maximum number of pci devices have been added. I have also tried setting up a virtual switch but it didn't seem like this would give full access to the nics. What is the best way to setup the nics to the VM has direct access to them? This is for a firewall VM.

  Read the article

• Windows Server 2008 - one MAC Address, assign multiple external IP's to VirtualBoxes running as guests on host

  - by Sise

  Couldn't find any help @ google or here. The scenario: Windows Server 2008 Std x64 on i7-975, 12 GB RAM. The server is running in a data centre. One hardware NIC - RealTek PCIe GBE - one MAC Address. The data centre provides us 4 static external IP's. The first is assigned to the host by default of course. I have ordered all 4 IP's, the data centre can assign the available IP's to the physical MAC address of the given NIC only. This means one NIC, one MAC Address, 4 IP's. Everything works fine so far. Now, what I would like to have: Installed VirtualBox with 1-3 guests running, each gets it's own external IP assigned. Each of it should be an standalone Win Server 2008. It looks like the easiest way would be to put the guests into an virtual subnet and routing all data coming to the 2nd till 4th external IP through to this guests using there subnet IP's. I have been through the VirtualBox User Manuel regarding networking. What's not working: I can't use bridged networking without anything else, because the IP's are assigned to the one MAC address only. I can't use NAT networking because it does not allow access from outside or the host to the guest. I do not wanna use port forwarding. Host-only networking itself would not allow internet access, by sharing the default internet connection of the host, internet is granted from the guest to the outside but not from outside or the host to the guest. InternalNetworking is not really an option here. What I have tried is to create an additional MS Loopback adapter for a routed subnet, where the Vbox guests are in, now the idea was to NAT the internet connection to the loopback 'subnet'. But I can't ping the gateway from the guests. By using route command in the command shell or RRAS (static route, NAT) I didn't get there as well. Solutions like the following do work for the one way, but not for the way back: For your situation, it might be best to use the Host-Only adapter for ICS. Go to the preferences of VB itself and select network. There you can change the configuration for the interface. Set the IP address to 192.168.0.1, netmask 255.255.255.0. Disable the DHCP server if it isn't already and that's it. Now the Guest should get an IP from Windows itself and be able to get onto the internet, while you can also access the Host. Slowly I'm pretty stucked with this topic. There is a possibility I've just overlooked something or just didn't getting it by trying, especially using RRAS, but it's kinda hard to find useful howto's or something in the web. Thanks in advance! Best regards, Simon

  Read the article

• Fedora12, XP and connection sharing via iptables

  - by Paul L

  Just a quick question ( I Hope ) To find out if what I'm trying is even possible. I am trying to share internet connection with Fedora12 as default gateway and XP machine hooked up via NIC using iptables commands as shown in Mark Sobell's book 'A Practical Guide To Fedora And Red Hat Enterprise Linux' These are the commands as placed in /etc/rc.local iptables -A FORWARD -i eth1 -o eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT iptables -A FORWARD -j LOG iptables -t NAT -A POSTROUTING -o eth1 -j MASQUERADE I did flip the in and out parameters to match my NIC configuration ( as opposed to example from book ) but other than that followed example. One thing to note is that Sobell did not mention whether this should work with mix of Linux and XP. One other note ( maybe meaningless ) is that I do have samba working between the two machines. Thanks for any insights anyone might have. PL

  Read the article

• How to separate Hyper-V Private network from the External network

  - by Ron Ratzlaff

  I am setting up a virtual test lab and I configured a domain controller VM running Windows 2008 R2 on my Hyper-V 2008 R2 server. I needed to download and install updates on it so I added an External NIC adapter and got that done. However, systems on my actual real physical domain were pulling IPs from this server and that was a big oopsy on my part so I immediately removed the External NIC adapter until I could find out how to go about keeping the Private and the External separate. If someone from the Server Fault community can help with this since I am pretty new to this, I would be very grateful. Thanks everyone.

  Read the article

• Good low power server/pc for firewall?

  - by Sandra

  Hi, Does anyone know of a low power server/pc that have 2 NIC's, so it can be used for a (OpenBSD) firewall? Sandra

  Read the article

• Good low power server/pc for firewall?

  - by Sandra

  Hi, Does anyone know of a low power server/pc that have 2 NIC's, so it can be used for a (OpenBSD) firewall? Sandra

  Read the article

• Emacs column editing CUA mode - is it possible to select rectangular region with mouse?

  - by MountainX

  Rectangular or column editing is possible in emacs. And it is very easy with cua-mode enabled. Here are my references for this: Here's a video that shows how to do it: http://vimeo.com/1168225 And see section "CUA rectangle support" here: http://www.cua.dk/cua.html But I also wonder if I can do it with the mouse. I want to select the rectangular region entirely with the mouse (like Scite or Geany can do). Is that possible in emacs?

  Read the article

• Sizing a Virtual Server

  - by vdubs

  I would like to replace four aging physical servers with one virtual server. What is the best way to insure the VM server is sized correctly? The requirements of the apps that will be running on the four servers are APPLICATION SERVERS - QTY 3 - These will run the application layer for the web server, Business Objects Business Intelligence app, and various other small client server apps. The three most heavy hitting apps each have the following server requirements. So, if I bought three physical servers, this would be the requirements for each of them Processor - Dual 2.83 GHZ (or faster) Ram - 4 GB Raid 5 - 50-100GB usable space NIC - 1 GB Web Server - this will run one asp.net e-business app that will talk to our dedicated SQL server and the three app servers above. The E-Business software has these requirements for the web server Processor - Quad 2.83 GHZ (or faster) Ram - 8 GB Raid 5 - 50-100GB usable space NIC - 1 GB What is the best tool to determine what I need from a hardware standpoing in a virtual server? I am planning on using VMWare.

  Read the article

• Google-Chrome 10 stable crash on every page

  - by Achu

  I installed google-chrome today, when i open any page including askubuntu i got this error message. i see my memory usage is normal(Memory 56% and swap 4.8%) also I reload and i go to another page same problem What is the problem? the last dmesg output [26612.341865] lo: Disabled Privacy Extensions [29651.852476] chrome[15472] general protection ip:1528e26 sp:7fff514a9dc0 error:0 in chrome[400000+3082000] [31447.190586] [UFW BLOCK] IN=eth1 OUT= MAC=00:1c:25:a1:e7:67:00:16:3e:28:5a:b7:08:00 SRC=172.23.100.6 DST=172.23.20.128 LEN=69 TOS=0x00 PREC=0x00 TTL=128 ID=15939 PROTO=UDP SPT=4243 DPT=161 LEN=49 [31451.250190] [UFW BLOCK] IN=eth1 OUT= MAC=00:1c:25:a1:e7:67:00:16:3e:28:5a:b7:08:00 SRC=172.23.100.6 DST=172.23.20.128 LEN=69 TOS=0x00 PREC=0x00 TTL=128 ID=16180 PROTO=UDP SPT=4243 DPT=161 LEN=49 [31454.260150] [UFW BLOCK] IN=eth1 OUT= MAC=00:1c:25:a1:e7:67:00:16:3e:28:5a:b7:08:00 SRC=172.23.100.6 DST=172.23.20.128 LEN=69 TOS=0x00 PREC=0x00 TTL=128 ID=16322 PROTO=UDP SPT=4243 DPT=161 LEN=49 [31458.648164] [UFW BLOCK] IN=eth1 OUT= MAC=00:1c:25:a1:e7:67:00:16:3e:28:5a:b7:08:00 SRC=172.23.100.6 DST=172.23.20.128 LEN=69 TOS=0x00 PREC=0x00 TTL=128 ID=16513 PROTO=UDP SPT=4243 DPT=161 LEN=49 [33124.300112] lo: Disabled Privacy Extensions [33601.021406] Skipping EDID probe due to cached edid [34594.043501] chrome[15746]: segfault at 0 ip 0000000000d5cdd0 sp 00007fff5149ec20 error 6 in chrome[400000+3082000] [34597.395334] chrome[18112] general protection ip:17c85bf sp:7fff514aa4f0 error:0 in chrome[400000+3082000] [34616.786643] chrome[18124]: segfault at 1007 ip 00000000017c849f sp 00007fff514aabd0 error 4 in chrome[400000+3082000] [37277.436207] lo: Disabled Privacy Extensions [38549.501390] e1000e: eth1 NIC Link is Down [38551.122253] e1000e: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX [38551.122263] e1000e 0000:00:19.0: eth1: 10/100 speed: disabling TSO

  Read the article

• Static Routes and the Routing Table

  - by TheD

  This is very much a learning question if someone would be happy to explain a couple of concepts. My question is - the default routing table that exists in, in my case, a default Windows 7 install, what do each of the routes in the table do? Here is a screenshot: The 10.128.4.0 is just a route I've added while messing. I understand from a question I posted on Superuser the first route is just a default route that will route all traffic for any IP to my default gateway on my Interface in use. But what about the others? And how would the routing table handle a machine with multiple NIC's, perhaps connected to two different networks, or maybe even two NIC's on the same network so a VM can have a physical Network card instead of each VM sharing the hosts. Thanks!

  Read the article

• Problem with Jumbo Frames

  - by Spookyone

  Hello, I am trying to set up jumbo frames on my gigabit home LAN but no luck so far. My setup is: * D-Link DIR-655 router, HW Revision A3, Firmware 1.21 EU * Synology DS107+, Firmware 3.0-1337 * Laptop w/ Win7 x64, external PCIx NIC managed by "Generic Marvel Yukon 88E8053 based Ethernet Controller" The router is supposed to support jumbo frames but doesn't feature any relevant setting. I set the Jumbo Packet value to 9000 on both the NIC and the Synobox but it doesn't work, ping -f -l 8972 says "Packet needs to be fragmented but DF set". Is there any other setting I overlooked, the DIR-655 doesn't actually support jumbo frames, or what else could be the problem?

  Read the article

• Bridging Network Devices with Multiple IPs

  - by Andy

  I have a small server with a single NIC that I am trying to get a bridge functioning on so that I can run KVM. On this NIC I have a couple IPs statically assigned to it: eth0 = 192.168.1.1 eth0:1 = 192.168.1.2 eth0:2 = 192.168.1.3 eth0:3 -> Assign the bridge to this I am attempting to set up a bridge using the following instructions: sudo brctl addbr br0 sudo brctl addif br0 eth0:3 sudo ifconfig br0 192.168.1.120 netmask 255.255.255.0 up sudo route add -net 192.168.1.0 netmask 255.255.255.0 br0 sudo route add default gw 192.168.1.1 br0 sudo tunctl -b -u root -t tap0 > /dev/null sudo ifconfig tap0 up sudo brctl addif br0 tap0 However, when I do the second command: sudo brctl addif br0 eth0:3 It puts the ENTIRE eth0 device into promiscuous mode. This knocks the server offline and inaccessible by anything other than locally. Is there a way to bridge JUST eth0:3 to br0 and not put the entire device into promiscuous mode?

  Read the article

• server pinging problem (privately)

  - by ankur kaushik

  i have two server and both have 2 nic one for private and one for public public networkworking properly and private netword not working properly and no pining

  Read the article

• What is this JavaScript gibberish?

  - by W3Geek

  I am studying how to make a 2D game with JavaScript by reading open source JavaScript games and I came across this gibberish... aSpriteData = [ "}\"¹-º\"À+º\"À+º\"À+º\"¿¤À ~C_ +º\"À+º\"À+º\"À*P7²OK%¾+½u_\"À<¡a¡a¡bM@±@ª", // 0 ground "a ' ![± 7°³b£[mt<Nµ7z]~¨OR»[f_7l},tl},+}%XN²Sb[bl£[±%Y_¹ !@ $", // 1 qbox "!A % @,[] ±}°@;µn¦&X£ <$ §¤ 8}}@Prc'U#Z'H'@· ¶\"is ¤&08@£(", // 2 mario " ´!A.@H#q8¸»e-½n®@±oW:&X¢a<&bbX~# }LWP41}k¬#3¨q#1f RQ@@:4@$", // 3 mario jump " 40 q$!hWa-½n¦#_Y}a©,0#aaPw@=cmY<mq©GBagaq&@q#0§0t0¤ $", // 4 mario run "+hP_@", // 5 pipe left "¢,6< R¤", // 6 pipe right "@ & ,'+hP?>³®'©}[!»¹.¢_^¥y/pX¸#µ°=a¾½hP?>³®'©}[!»¹.¢_^ Ba a", // 7 pipe top left "@ , !] \"º £] , 8O #7a&+¢ §²!cº 9] P &O ,4 e", // 8 pipe top right " £ #! ,! P!!vawd/XO¤8¼'¤P½»¹²'9¨ \"P²Pa²(!¢5!N*(4´b!Gk(a", // 9 goomba " Xu X5 =ou!¯­¬a[Z¼q.°u#|xv ¸··@=~^H'WOJ!¯­¬a=Nu ²J <J a", // 10 coin // yui "@ & !MX ~L \"y %P *¢ 5a K w !L \"y %P *­a%¬¢ 4 a", // 11 ebox // yui "¢ ,\"²+aN!@ &7 }\"²+aN!XH # }\"²+aN!X% 8}\"²+aN!X%£@ (", // 12 bricks "} %¿¢!N° I¨²*<P%.8\"h,!Cg r¥ H³a4X¢*<P%.H#I¬ :a!u !q", // 13 block makeSpace(20) + "4a }@ }0 N( w$ }\" N! +aa", // 14 bush left " r \"²y!L%aN zPN NyN#²L}[/cy¾ N" + makeSpace(18) + "@", // 15 bush mid makeSpace(18) + "++ !R·a!x6 &+6 87L ¢6 P+ 8+ (", // 16 bush right " %©¦ +pq 7> \"³ s" + makeSpace(25) + "@", // 17 cloud bottom left "a/a_#².Q¥'¥b}8.£¨7!X\"K+5cqs%(" + makeSpace(18) + "0", // 18 cloud bottom mid "bP ¢L P+ 8%a,*a%§@ J" + makeSpace(22) + "(", // 19 cloud bottom right "", // 20 mushroom "", // koopa 16x24 "", // 22 star "", // 23 flagpole "", // 24 flag "", // 25 flagpole top " 6 ~ }a }@ }0 }( }$ }\" }! } a} @} 0} (} $} \"² $", // 26 hill slope "a } \"m %8 *P!MF 5la\"y %P" + makeSpace(18) + "(", // 27 hill mid makeSpace(30) + "%\" t!DK \"q", // 28 hill top "", // 29 castle bricks "", // 30 castle doorway bottom "", // 31 castle doorway top "", // 32 castle top "", // 33 castle top 2 "", // 34 castle window right "", // 35 castle window left "", // 36 castle flag makeSpace(19) + "8@# (9F*RSf.8 A¢$!¢040HD", // 37 goomba flat " *(!¬#q³¡[_´Yp~¡=<¥g=&'PaS²¿ Sbq*<I#*£Ld%Ryd%¼½e8H8bf#0a", // 38 mario dead " = ³ #b 'N¶ Z½Z Z½Z Z½Z Z½Z Z½Z Z½Z =[q ²@ ³ ¶ 0", // 39 coin step 1 " ?@ /q /e '¤ #³ !ºa }@ N0 ?( /e '¤ #³ ¿ _a \"", // 40 coin step 2 " / > ] º !² #¢ %a + > ] º !² #¢ 'a \"", // 41 coin step 3 " 7¢ +² *] %> \"p !Ga t¢ I² 4º *] %> \"p ¡ Oa \"" // 42 coin step 4 ], What does it do? If you want to look at the source file here it is: http://www.nihilogic.dk/labs/mario/mario.js Beware, there is more gibberish inside. I can't seem to make sense of any of it. Thank you.

  Read the article

• Using USB to Ethernet with Linux Ubuntu 12.04

  - by Sriram

  Being a newbie, Please excuse if the technical Jargon used is not an universally accepted one :) I have a particular device (say device A) whose USB2.0 driver is available from Linux community. Linux UBUNTU12.04 based PC is able to detect that device via the available driver. My requirement is to ensure that PC can exchange the command as well as data with the device A over TCP/IP packets (In other words, instead of just a USB Based driver, there should be a TCP/IP wrapper over the device USB driver and still does the same job as the USB driver was doing before) Bought an USB (Female) to RJ-45 adapter,connected Device A (male) USB to the USB Female end of the adapter and the Ethernet end connected to the router. PC also is connected to the same router so that both Device A and the PC have the IP address in the same subnet range. So the packets produced by the device A can be routed to the PC via some binding( not sure how I can achieve this, but conceptual idea) Here are the issues I can see as of now 1) USB to RJ-45 is just a hardware signal conversion and not a NIC in itself and hence no MAC/IP ADDRESS assigned. Can we bind a virtual NIC created in PC with this connector? 2) Any available USB TO IP command as well as data translation wrappers available? e.g. command for the device A on Ethernet converted to command for the device A on USB which is then acted upon the device as a command from the USB driver There is some missing link in my understanding and hence it would be of great help if you can bounce off some ideas on how I can take this forward so that Device A and PC exchange data over IP. Thanks and Regards, Sriram

  Read the article

• URL rewrite and domain frame

  - by Dennis

  I have registered the domain www.posti.sh at nic.sh. The website is on the server www.myskoob.com/postish. Unfortunately, nic.sh does not support frames, i.e. that the domain stays posti.sh as it forwards to www.myskoob.com/postish - so I thought about a URL rewrite on the server. Unfortunately I have no idea how rewriting works - I am thankful for explanations - but I would also like to ask whether this is generally possible. What I need is: The server needs to recognize that the folder postish is accessed Depending on the file that is opened, it needs to rewrite the url to www.posti.sh/<-according filename here- Also, the server needs to understand that a link to www.posti.sh/about.php links to www.myskoob.com/postish/about.php and likewise for other files - at the moment, when I type in posti.sh/about.php it redirects to http://www.myskoob.com/postishabout.php, which does not exist All this should be possible irrespective of whether the url contains a "www" at the beginning or not A plus but not necessary would be that it does not display the .php extensions Would that generally be possible? If not, what would be the alternatives? If anyone knows how to do it, any code and/or way to do it would be much appreciated!

  Read the article

• Hyper-V virtual machine unable to get IP address from DHCP server running on same physical box

  - by Bronumski

  We have a Windows server 2008 R2 with two network cards running AD, DHCP, DNS and Hyper-V The first nic is setup with a static IP address and DHCP, WDS, and DNS are bound to it. The second nic is configured in Hyper-V to be only used by Hyper-V and has been automatically configured so that only the virtual switch is enabled on the adapter. DHCP and DNS work fine for all physical machines on the network. It also works for Virtual Machines running on another physical box. Virtual machines that are bound to the virtual switch network adapter are unable to get a IP address. If the virtual machine is given a static IP address with correct subnet, gateway and dns everything works. Has anyone else got this working?

  Read the article

• Wake On Lan only works on first boot, not sequent ones

  - by sp3ctum

  I have converted my old Dell Latitude D410 laptop to a server for tinkering. It is running an updated Debian Squeeze (6) with a Xen enabled kernel (I want to toy with virtual machines later on). I am running it 'headless' via an ethernet connection. I am struggling to enable Wake On Lan for the box. I have enabled the setting in the BIOS, and it works nicely, but only for the first time after the power cord is plugged in. Here is my test: Plug in power cord, don't boot yet Send magic Wake On Lan packet from test machine (Ubuntu) using the wakeonlan program Server expected to start (does every time) Once server has booted, log in via ssh and shut it down via the operating system After shutdown, wake server up via WOL again (fails every time) Some observations: Right after step 1 I can see the integrated NIC has a light on. I deduce this means the NIC gets adequate power and that the ethernet cable is connected to my switch. This light is not on after step 4 (the shutdown stage). The light becomes back on after I disconnect and reconnect the power cord, after which WOL works as well. After step 4 I can verify that wake on lan is enabled via the ethtool program (repeatable each time) This blog post suggested the problem may lay in the fact the motherboard might not be giving adequate power to the NIC after shutdown, so I copied an acpitool script that supposedly should signal the system to give the needed power to the card when shut down. Obviously it did not fix my issue. I have included the relevant power settings in the paste below. I have tried different combinations of parameters of shutdown (the program) options, as well as the poweroff program. I even tried "telinit 0", which I figured would do the most direct boot via software. If I keep the laptop's power button pressed down and do a hard boot this way, the light on the ethernet port stays lit and a WOL is possible. I copied a bunch of hopefully useful information in this paste I have tried this with the laptop battery connected and without it. I get the same result. Promptly pressing the power button causes the system to shut down with the message "The system is going down for system halt NOW!", and WOL is still unsuccessful.

  Read the article

• User Group meeting in Copenhagen for #powerpivot

  - by Marco Russo (SQLBI)

  The next Monday, March 21st, I will join a special event organized by the Danish SQL Server User Group , Excelbi.dk and the Swedish SQL Server User Group . The meeting will start at 18:00 at the Radisson Royal Blu in Copenhagen, and this is the topic we will discuss. PowerPivot / BISM and the future of a BI Solution The next version of Analysis Services will offer the BI Semantic Model (BISM) that is based on Vertipaq, the same engine that runs PowerPivot. DAX and PowerPivot have been created as...(read more)

  Read the article

• Can't access certain specific IP/domain on Windows 7

  - by jfrobishow

  Been banging my head on the wall for some time now. I have a fresh install of Windows 7 - Ultimate ~x86. Some IPs can't resolve properly, it doesn't matter if I try using Firefox, Chrome or IE I end up with a domain not found (server not found, etc.) I am behind a router, all the other computers aren't affected only this Win 7 machine. It's only certain sites. e.g. xkcd.com, facebook's cdn, google group. Things I have tried: flushdns ipconfig renew Disable IP v6 on the NIC Double checked that the computer was in the right timezone @ the right time. Reinstall the NIC driver. Again 90% of the sites will work but not the major one :P help!!!

  Read the article

< Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >