Search Results

Search found 8684 results on 348 pages for 'nunit console'.

Page 190/348 | < Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >

• What happens when the USB key or SD card I've installed VMware ESXi on fails?

  - by ewwhite

  An SD (SDHC) card installed in an HP ProLiant DL380p Gen8 server running VMware ESXi just failed. I encountered some rather ominous looking messages on the vCenter console and in the HP ProLiant ILO event log... Lost connectivity to the device ... backing the boot filesystem. As a result, host configuration changes will not be saved to persistent storage. Embedded Flash/SD-CARD: Error writing media 0, physical block 848880: Stack Exception. VMware advocates the use of USB and SD (SDHC) boot devices for ESXi. It was one of the main reasons the smaller footprint ESXi was developed (versus the older ESX). I've spent much time highlighting the differences between ESXi's installable and embedded modes to coworkers and clients. However, these failures do seem to happen. In this case, this is my third instance. Luckily, this is a vSphere cluster with SAN storage. What steps should be taken to remediate this failure?

  Read the article

• Troubleshooting Amazon EC2 reboot

  - by tgm

  We've had a server (CentOS) running in EC2 for a few months. It had been going pretty smoothly until today when we got an alarm that the server was unavailable (HTTP service couldn't be reached). So I tried SSHing into the box but that timed out as well. I logged into the EC2 console and it said the instance was running and there wasn't anything in the system log. One odd thing I noticed is that even though we have an Elastic IP attached to it (which shows in the Elastic IP management area), the instance detail is not showing that there is an EIP associated with the instance. I looked through the message log and the last thing I see around the time we got our alert was the dhclient renewed the lease. I'm guessing there may have been some sort of issue with the networking. How might I check if that was the problem, or if there were any other issues that may have caused our instance to stop responding?

  Read the article

• Entering BIOs Setup from Supermicro IPMI KVM

  - by Joshua Lim

  I'm having trouble getting into BIOs Setup from Supermicro IPMI "KVM" - Remote Control Console Redirection. I need to change the boot order to CDROM first. I'm running Windows 2008 server. After some Googling, it says here that the method is to: Press TAB to enter Setup screen. Press Esc twice to take effect. http://www.supermicro.com/support/faqs/faq.cfm?faq=6222 A month ago, I tried that 30-40 times + DEL, over 2 hours, it worked. Now, I've been trying the same key combination for more than an hour, rebooting each time it failed, it still doesn't work. Note: I've only got a notebook computer, no extra monitor.

  Read the article

• Running Batch File As An Administrator…

  - by WidmarkRob

  I successfully created a batch file to flush my DNS. I have added a pause, I noticed in the title bar of the console window… It's not running as administrator. I've already tried a couple of variations of this… Just a little guidance would be most appreciated. I remember reading a blog somewhere, it said something about capitalization wasn't important… Is camel casing important in writing batch files? @echo off echo. pause CD.. CD.. echo. runas /user:<Administrator> ipconfig /flushdns echo. pause echo.

  Read the article

• Cisco PIX 515 internet connection

  - by Steve

  We have a ASDL modem connected to a Cisco PIX 515 to a switch. We have managed to get the PIX setup with ethernet1 (inside) with our IP range 192.168.5.1-192.168.5.254 and the internal network is working fine. We are having difficulty getting a connection from the PIX through the router on ethernet0 (outside). We have managed to ping external networks by setting up IMCP echo/echo-reply but are unable to setup any other protocols in a similar manner. Can any one help with a few lines that could be typed into the console that will allow this connection?

  Read the article

• straight to grub prompt on boot

  - by cheshirekow

  I am very lost. I did a fresh install of Ubuntu 10.04 on a laptop. First reboot was fine. I ran all the recommended upgrades, and now every time I start I get just a grub>_ prompt. No error message, just the prompt, and a little banner at the top saying grub's version and telling me that I have minimal bash style editing. I've tried: 1) Re-installing grub via sudo grub-install sda (There is only one disk with only two partitions, one primary, and one for swap) 2) Changed GRUB_HIDDEN_TIMEOUT=10 GRUB_TIMEOUT=30 GRUB_CMDLINE_LINUX_DEFAULT="rootdelay=90" GRUB_CMDLINE_LINUX="rootdelay=90" in /etc/default/grub. No luck. I can boot with the following: grub> set root=(hd0,1) grub> probe (hd0,1) -u c00fadde-f7e8-45e7-a4da-0235605f756 grub> linux /boot/vmlinuz-2.6.32-21-generic root=UUID=c00fadde-f7e8-45e7-a4da-0235605f756 rootdelay=90 grub> initrd /boot/initrd.img-2.6.32-21-generic grub> boot And then everything seems to be fine from there. From the grub prompt if I try configfile /boot/grub/grub.cfg The screen clears and I get another grub prompt. So, seriously, what could the problem be? edit: Full text of /boot/grub/grub.cfg # # DO NOT EDIT THIS FILE # # It is automatically generated by /usr/sbin/grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then load_env fi set default="0" if [ ${prev_saved_entry} ]; then set saved_entry=${prev_saved_entry} save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z ${boot_once} ]; then saved_entry=${chosen} save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n ${have_grubenv} ]; then if [ -z ${boot_once} ]; then save_env recordfail; fi; fi } insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 insmod gfxterm insmod vbe if terminal_output gfxterm ; then true ; else # For backward compatibility with versions of terminal.mod that don't # understand terminal_output terminal gfxterm fi fi insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 set locale_dir=($root)/boot/grub/locale set lang=en insmod gettext if [ ${recordfail} = 1 ]; then set timeout=-1 else set timeout=30 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.32-21-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 linux /boot/vmlinuz-2.6.32-21-generic root=UUID=c00fadde-f7e8-45e7-a4da-0235c605f756 ro rootdelay=90 rootdelay=90 initrd /boot/initrd.img-2.6.32-21-generic } menuentry 'Ubuntu, with Linux 2.6.32-21-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 echo 'Loading Linux 2.6.32-21-generic ...' linux /boot/vmlinuz-2.6.32-21-generic root=UUID=c00fadde-f7e8-45e7-a4da-0235c605f756 ro single rootdelay=90 echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.32-21-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### if [ ${timeout} != -1 ]; then if sleep --verbose --interruptible 10 ; then set timeout=0 fi fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### output of update-grub Generating grub.cfg ... Found linux image: /boot/vmlinuz-2.6.32-21-generic Found initrd image: /boot/initrd.img-2.6.32-21-generic Found memtest86+ image: /boot/memtest86+.bin done contents of /boot total 14280 -rw-r--r-- 1 root root 640617 2010-04-16 09:01 abi-2.6.32-21-generic -rw-r--r-- 1 root root 115847 2010-04-16 09:01 config-2.6.32-21-generic drwxr-xr-x 3 root root 4096 2010-09-08 02:42 grub -rw-r--r-- 1 root root 7968754 2010-09-02 01:49 initrd.img-2.6.32-21-generic -rw-r--r-- 1 root root 160280 2010-03-23 05:37 memtest86+.bin -rw-r--r-- 1 root root 1687378 2010-04-16 09:01 System.map-2.6.32-21-generic -rw-r--r-- 1 root root 1196 2010-04-16 09:03 vmcoreinfo-2.6.32-21-generic -rw-r--r-- 1 root root 4029792 2010-04-16 09:01 vmlinuz-2.6.32-21-generic

  Read the article

• How do I make kdump use a permissible range of memory for the crash kernel?

  - by Philip Durbin

  I've read the Red Hat Knowledgebase article "How do I configure kexec/kdump on Red Hat Enterprise Linux 5?" at http://kbase.redhat.com/faq/docs/DOC-6039 and http://prefetch.net/blog/index.php/2009/07/06/using-kdump-to-get-core-files-on-fedora-and-centos-hosts/ The crashkernel=128M@16M kernel parameter works fine for me in a RHEL 6.0 beta VM, but not on the RHEL 5.5 hosts I've tried. dmesg shows me: Memory for crash kernel (0x0 to 0x0) notwithin permissible range disabling kdump Here's the line from grub.conf: kernel /vmlinuz-2.6.18-194.3.1.el5 ro root=/dev/md2 console=ttyS0,115200 panic=15 rhgb quiet crashkernel=128M@16M How do I make kdump use a permissible range of memory for the crash kernel?

  Read the article

• Mac Mail import from Entourage failed

  - by elhombre

  I am trying to import the entire Folder-structure from Entourage 2008 to Mac Mail on a Mac OS X 10.5.8. First I wanted to export the whole E-Mail Database from Entourage to Desktop as a .rge File. The export got aborted through a message which indicated that my Entourage database is corrupt and that I should rebuild it. I then went over to Mac Mail and imported the Entourage Folder-structure through File/import mailboxes.../Entourage. The bulky import did take some time and the progress bar never reached its full length. But at the end the import was successful. When I checked the imported folder-structure in Mac Mail I noticed that quiet a few Subfolders where missing. I checked Console and saw following message. Mail[2899] Applescript Error: aliasForMailImporter got an error: AppleEvent handler failed. Question: What does that mean and what can I do to get my subfolder-structure over completely?

  Read the article

• Hyper-V VMs hanging 10 minutes after startup

  - by Ken George

  Hyper-V running under a fresh install of 2008 R2 DC 2 VMs both running 2008 R2 STD One VM has SQL 2008 Server w/ SP2 and Office 2007 Enterprise w/ SP2 Othe VMS only Office 2007 w/ SP2. Approximately 10 minutes after reboot the Hyuper-V host the VMs will hang Hang = answers pings, but no RDP connections and Hyper-V console session is non responsive Disabled Hyper-V and had no proble with 2008 R2 DC host. Started the three Hyper-V services and 10 minutes later was hung again. Hardware is HP DL380 G4 2 socket, 48 GB, Internal SAS controller 1.5TB C drive VMs .VHDs are on external SAS controller on a 1.5 TB RAID5 volume. Nothing in event log on either VMs or Hyper-V host. Ken

  Read the article

• Improper output in SSH session on OSX using FreeSSHd on Windows with cygwin bash/sh shell

  - by Tyler Clendenin

  I am testing out running an SSH server on a local Windows VM. I have installed FreeSSHd and set the command shell to "c:\cygwin\bin\sh --login -i" (bash as well) with "Use new console engine" unchecked. (When it was enabled no output would show through the ssh connection anyway) The shell seems to work, but when connecting from my OS-X terminal using ssh all of the shell results comes out ill formatted. $ ls -al total 17 drwxr-xr-x+ 1 SYSTEM Administrators 4096 Feb 2 01:00 . drwxrwxrwt+ 1 Administrator Administrators 0 Feb 2 01:01 .. -rw------- 1 SYSTEM Administrators 128 Feb 2 01:30 .bash_history -rwxr-xr-x 1 SYSTEM Administrators 1150 Feb 2 00:55 .bash_profile -rwxr-xr-x 1 SYSTEM Administrators 3754 Feb 2 00:55 .bashrc -rwxr-xr-x 1 SYSTEM Administrators 1461 Feb 2 00:55 .inputrc Any ideas on why this is happening, how I can fix this?

  Read the article

• Windows Server 2003 Licensing

  - by Phil

  Hi all, I'm looking to get a Windows Server 2003 box in the middle of my linux network. :( I'm just concerned about CAL licensing for it. No devices will access any network server function of Windows Server 2003. I don't need Windows for DHCP or DNS or file and print sharing. I have linux boxes to do that! xD I just need a box running Windows (of some variety) to host those few apps that have to run on Windows like my AV management console. In short do I need any CALs for my server if its not acting as server itself. I think Windows Server 2003 comes with 5 CALs which can be per user for the admins to use RDP? Thanks, Phil

  Read the article

• How do I elevate privileges when running appcmd from a nant task?

  - by Rune

  We are using a Windows 7 box as build server. As part of our continuous integration process I would like to stop and start an IIS 7 website. I have tried doing this from the command line using appcmd: appcmd start site "my website" However, this only works if I start the console window by choosing "Run as Administrator", so it won't work out-of-the-box from NAnt etc. How do I script appcmd to be run with elevated privileges (or am I going about this in the wrong way)? Thank you.

  Read the article

• Forcing DFS replication on Windows 2003 Web Edition SP2

  - by Greg B

  I have a pair of web servers running Windows Server 2003 Web Edition SP2 (build 3790). There servers are a on a Gigabit LAN and are on the same subnet. I created a new link on the 1st server and added the second box as a target to the link. I configured replication as ring. The 2nd server gets some of the files on the scheduled replication but this varies wildly which makes me think it's not running fully. The folder on server 1 is 1.3GB. Is there some way I can force repication (from a console?) and monitor the progress and see if/when/why it fails.

  Read the article

• Can I shorten my directory commands in ubuntu?

  - by Spencer Cooley

  When working on a rails app I like to open all of my files through the command line like so cd my_app gedit app/views/user/show.html.erb Is there a way that I could shorten this so that I could just write something like gedit user_views/show.html.erb ? I would like the console to stay in the main directory, I just don't like having to type out app/controller/user_controler.rb every time I want to open the user controller. I know that I could just open the file with my mouse, but I feel like moving from keyboard to mouse breaks my focus a little bit. When I can just tap away at the keyboard it seems like I have a more smooth workflow.

  Read the article

• Can I shorten my directory commands in ubuntu?

  - by Spencer Cooley

  When working on a rails app I like to open all of my files through the command line like so cd my_app gedit app/views/user/show.html.erb Is there a way that I could shorten this so that I could just write something like gedit user_views/show.html.erb ? I would like the console to stay in the main directory, I just don't like having to type out app/controller/user_controler.rb every time I want to open the user controller. I know that I could just open the file with my mouse, but I feel like moving from keyboard to mouse breaks my focus a little bit. When I can just tap away at the keyboard it seems like I have a more smooth workflow.

  Read the article

• IPcop Multiple WAN Subnets

  - by obsidian

  We have an IPcop firewall and have had no issues with it. We've had a block of 10 IP addresses from our colocation provider and have been able port forward from those to internal servers as needed. We've recently needed additional IPs and the colocation provider issued an additional block of 10. The problem: The 10 new IP addresses issued are in a different subnet with a different gateway. The question: How do I add the new gateway into IPcop? How do I make it so that any outbound traffic in response to any inbound traffic from a new IP go back out through the new gateway? I attempted to add a static route via the console using the following command: route add -net x.x.x.x gw x.x.x.x netmask 255.255.255.192 I also added the new IPs as aliases and setup port forwarding as I've done with the existing IP block. However, when I attempt to access a web server from an external workstation, it just times out. Thanks in advance for your assistance.

  Read the article

• Virtualbox two networks slow

  - by Petr Marek

  I am running an Ubuntu server guest on Win 7 guest, and am running a webrick server (RoR dev). If I have just a host-only network, everything works fine and the browser response is instant. However, if I add a second network (NAT), so that the server can connect to the internet (for various updates etc.), the host-to-guest access gets really slow. I can't use the bridge connection. I am using the port 3000 (RoR Webrick server) and connecting to the guest via internet browser on this port (eg http://192.168.56.102:3000). Any idea, what could be causing this? If I ping the IP from host console, I get < 0ms. Here are the settings (relevant info is in english; Povoleno vše is Everything is allowed):

  Read the article

• How to blacklist a problem wifi access point by MAC address in OSX

  - by Sam Alexander

  So I am a small mac-user cog in a larger windows-based network machine. The network here works fine for most everyone else (on PCs), but I have random timeouts and issues with the Wifi. Luckily, I have identified a few problem access points by MAC address (via their log messages in Console.app). Is it possible to tell my Airport on my Macbook to avoid those access points, and only speak with the access points who are far less touchy about me drinking the Apple kool-aid? All of the points are on the same network SSID.

  Read the article

• PHP stop working after a server reboot

  - by Ido Bukin

  I reboot my server and suddenly the PHP-FastCGI stop working . I try to do - /etc/init.d/php-fastcgi restart Also i try to restart my Nginx : /etc/init.d/php-fastcgi restart How can i turn on my PHP again ?? My server run - Ubuntu 11.10 Nginx 1.2.3 MySQL PHP-FastCGI Also i want to ask it is possible that i have 2 Nginx installs on my server and they run in the same time ? when i check the Nginx version in the console its says that the version is 1.2.3 And when i go to my site i see - 502 Bad Gateway nginx/1.0.5 How can i fix this ?

  Read the article

• How to move 100mb hidden system reserved partition on Windows Server 2008 R2 to other drive?

  - by Artyom Krivokrisenko

  Hello! I have a server with two 1.5TB hard drives. I was going to install a Windows Server 2008 R2 and create software RAID1 using Windows Disk Management Utility. I instaleld Windows, open this console and that is what I see: http://i.imgur.com/KoC9a.png Setup program created a System Reserved Partition at my second HDD. I don't understand now, how can I create RAID1, because space, which supposed to be used for copy of disk C, now is used for this hidden partition. So is there any way now to create correct RAID1? May it is possible to move this partition to the Disk 0, where I have plenty of free space? Unfortunately I can't reinstall Windows and apply other options at the disk management step of the installation, because installation image is not longer connected to the server and I have no physical access to server, only remote desktop.

  Read the article

• Problem restarting my Ubuntu system

  - by VoY

  Whenever I try to restart my Ubuntu either from the command line by typing reboot or in GNOME the computer goes from X to console, starts the shutdown process and then a message saying "[ some number ] Starting new kernel" appears on the screen and the computer goes back to X login screen. I suspect this must have something to do with nvidia drivers, because it seemed to have appeared around the time I bought a new graphic card. Also, when I reboot the second time I see weird graphical artifacts on the screen. When I boot from ubuntu live cd I can reboot just fine. I used jaunty, recently I switched to karmic with no change. This bug is very annoying, because I have to hard reset my computer in order to reboot. Also not good for the filesystems, I suspect. Can you suggest a way to debug the cause or if not at least the easiest way to go about reinstalling ubuntu without losing customizations/settings/data?

  Read the article

• Office 365 Powershell - Export user, license type, and company field to csv file

  - by ASGJim

  I need to be able to export user name or email address (doesn't matter which), company (from the company field under the organization tab in a user account of the exchange admin console), and license type (e.g. exchange online e1, exchange online kiosk etc...) I am able to export both values in two statements into two separate files but that doesn't do me much good. I can export the username and license type with the following: Get-MSOLUser | % { $user=$_; $_.Licenses | Select {$user.displayname},AccountSKuid } | Export-CSV "sample.csv" -NoTypeInformation And, I can get the company values with the following: Get-User | select company | Export-CSV sample.csv Someone on another forum suggested this - $index = @{} Get-User | foreach-object {$index.Add($_.userprincipalname,$_.company)} Get-MsolUser | ForEach-Object { write-host $_.userprincipalname, $index[$_.userprincipalname], $_.licenses.AccountSku.Skupartnumber} That seems like it should work but it doesn't display any license info in my powershell, it's just blank. Also I wouldn't know how to export that to a csv file. Any help would be appreciated. Thanks.

  Read the article

• Filezilla/Puttygen doesn't recognize private key file

  - by devzoner

  I have generated a key for an Ubuntu Virtual Machine running on Azure Cloud Services http://www.windowsazure.com/en-us/manage/linux/how-to-guides/ssh-into-linux/ openssl req -x509 -nodes -days 365 -newkey rsa:2048 -keyout myPrivateKey.key -out myCert.pem When loading the private key into Filezilla, it asks me to convert the format, however, when converting the key it fails, the same happens with puttygen from linux console, using this: puttygen myPrivateKey.key -o myKey.ppk In both cases I have the following error: puttygen: error loading `myPrivateKey.key': unrecognised key type By the way, this key doesn't have a passphrase. I found an old thread about it, but I'm using 0.6.3 version which is newer than what this thread recommends: http://fixunix.com/ssh/541874-puttygen-unable-import-openssh-key.html I've managed to solve this issue by using another gui client Fugu for Mac, but one of my co-worker uses windows and I still have to figure this out. Since Filezilla is the de-facto ftp client, I thought it would be easier to solve it there. Thanks

  Read the article

• Oracle on NFS vmdk beats native NFS!?

  - by fletch00

  Hi, my colleagues are pursuing this with Netapp and Oracle - but I thought I'd post here on the off chance someone else has seen this We have a RedHat 5 VM (fully up2date) running Oracle 11i with data disks mounted via the VM's linux kernel NFS using Oracle's recommended mount options and the performance is very inconsistent (Querys that should take < 2 seconds sometimes take 60 seconds) Funny thing is we can run the same queries perfectly consistently < 2 seconds on a VMDK residing on SAME NetApp NFS datastore! Makes me wish Oracle and NetApp collaborated as closely as VMware and NetApp did on the Virtual Storage Console we used to perfectly set the NFS options and keep them in compliance... We have tried a few Linux NFS options others have posted and not seen improvement so far. We are now creating VMDK's for the VM to replace the Linux NFS mounted and workaround the issue as our developers need consistent performance ASAP.

  Read the article

• Can't bind spawn-fcgi to address

  - by Xeoncross

  Following some nice instructions I am almost through setting up PHP to run on nginx. However, every time I try to start spawn-fcgi I get an error message demo@desktop:/usr/bin$ sudo /etc/init.d/php-fastcgi start spawn-fcgi: bind failed: Cannot assign requested address My /etc/init.d/php-fastcgi startup script is: #!/bin/bash PHP_SCRIPT=/usr/bin/php-fastcgi FASTCGI_USER=demo RETVAL=0 case "$1" in start) su - $FASTCGI_USER -c $PHP_SCRIPT RETVAL=$? ;; stop) killall -9 php5-cgi RETVAL=$? ;; restart) killall -9 php5-cgi su - $FASTCGI_USER -c $PHP_SCRIPT RETVAL=$? ;; *) echo "Usage: php-fastcgi {start|stop|restart}" exit 1 ;; esac exit $RETVAL console output which loads /usr/bin/php-fastcgi #!/bin/sh /usr/bin/spawn-fcgi -a 127.0.0.1 -p 9000 -C 6 -u demo -f /usr/bin/php5-cgi One thing to note is that I am running the PHP cgi as the user "demo" which is my account.

  Read the article

< Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >