Search Results

Search found 11536 results on 462 pages for 'whole foods market'.

Page 190/462 | < Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >

  • Server Cabinet/Room Cooling

    - by user37226
    Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

    Read the article

  • DRBD not syncing between my nodes when IP is reset

    - by ramdaz
    I am trying to setup DRBD by following the article at http://www.howtoforge.com/setting-up-network-raid1-with-drbd-on-ubuntu-11.10-p2 I am using Ubuntu 10.04 DRBD - 8.3.11 In the first run I had everything working perfectly and when shifting the systems to a production environment I decided to restart the Meta Data creation part and start from scratch. The IPs had changed entirely in the production environment. Issuing drdbadm create-md r0 in both the servers runs successfully. But when I do "drbdadm -- --overwrite-data-of-peer primary all" on the primary it fails to start the re sync. My config file is as given below resource r0 { protocol C; syncer { rate 50M; } startup { wfc-timeout 15; degr-wfc-timeout 60; } net { cram-hmac-alg sha1; shared-secret "aklsadkjlhdbskjndsf8738734jkfkjfkjf"; } on primaryds { device /dev/drbd0; disk /dev/md2; address 172.16.7.1:7788; meta-disk internal; } on secondaryds { device /dev/drbd0; disk /dev/md2; address 172.16.7.3:7788; meta-disk internal; } } Status on primary root at primaryds:~# cat /proc/drbd version: 8.3.7 (api:88/proto:86-91) GIT-hash: ea9e28dbff98e331a62bcbcc63a6135808fe2917 build by root at primaryds, 2012-05-12 15:08:01 0: cs:WFBitMapS ro:Primary/Secondary ds:UpToDate/Inconsistent C r---- ns:0 nr:0 dw:0 dr:200 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:b oos:5690352828 Status on secondary root at secondaryds:/etc/drbd.d# cat /proc/drbd version: 8.3.7 (api:88/proto:86-91) GIT-hash: ea9e28dbff98e331a62bcbcc63a6135808fe2917 build by root at secondaryds, 2012-05-12 15:25:25 0: cs:WFBitMapT ro:Secondary/Primary ds:Inconsistent/UpToDate C r---- ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:b oos:5690352828 Log of Primary May 30 13:42:23 primaryds kernel: [ 1584.057076] block drbd0: role( Secondary -> Primary ) disk( Inconsistent -> UpToDate ) May 30 13:42:23 primaryds kernel: [ 1584.086264] block drbd0: Forced to consider local data as UpToDate! May 30 13:42:23 primaryds kernel: [ 1584.086303] block drbd0: Creating new current UUID May 30 13:42:26 primaryds kernel: [ 1586.405551] block drbd0: drbd_sync_handshake: May 30 13:42:26 primaryds kernel: [ 1586.405564] block drbd0: self E8A075F378173D4B:0000000000000004:0000000000000000:0000000000000000 bits:1422588207 flags:0 May 30 13:42:26 primaryds kernel: [ 1586.405574] block drbd0: peer 0000000000000004:0000000000000000:0000000000000000:0000000000000000 bits:1422588207 flags:0 May 30 13:42:26 primaryds kernel: [ 1586.405582] block drbd0: uuid_compare()=2 by rule 30 May 30 13:42:26 primaryds kernel: [ 1586.405587] block drbd0: Becoming sync source due to disk states. May 30 13:42:26 primaryds kernel: [ 1586.405592] block drbd0: Writing the whole bitmap, full sync required after drbd_sync_handshake. May 30 13:42:27 primaryds kernel: [ 1588.171638] block drbd0: 5427 GB (1422588207 bits) marked out-of-sync by on disk bit-map. May 30 13:42:27 primaryds kernel: [ 1588.172769] block drbd0: conn( Connected -> WFBitMapS ) Log in Secondary May 30 13:42:24 secondaryds kernel: [ 1563.304894] block drbd0: peer( Secondary - Primary ) pdsk( Inconsistent - UpToDate ) May 30 13:42:24 secondaryds kernel: [ 1563.339674] block drbd0: drbd_sync_handshake: May 30 13:42:24 secondaryds kernel: [ 1563.339685] block drbd0: self 0000000000000004:0000000000000000:0000000000000000:0000000000000000 bits:1422588207 flags:0 May 30 13:42:24 secondaryds kernel: [ 1563.339695] block drbd0: peer E8A075F378173D4B:0000000000000004:0000000000000000:0000000000000000 bits:1422588207 flags:0 May 30 13:42:24 secondaryds kernel: [ 1563.339703] block drbd0: uuid_compare()=-2 by rule 20 May 30 13:42:24 secondaryds kernel: [ 1563.339709] block drbd0: Becoming sync target due to disk states. May 30 13:42:24 secondaryds kernel: [ 1563.339714] block drbd0: Writing the whole bitmap, full sync required after drbd_sync_handshake. May 30 13:42:26 secondaryds kernel: [ 1565.652342] block drbd0: 5427 GB (1422588207 bits) marked out-of-sync by on disk bit-map. May 30 13:42:26 secondaryds kernel: [ 1565.652965] block drbd0: conn( Connected - WFBitMapT ) The serves are not responding once it reaches this stage. Tried redoing it couple of time but noting happens. Why could the resync not be taking place? I would like some advice? Directions?

    Read the article

  • Do hard drive enclosures fail/is it the HDD or enclosure?

    - by x0a
    I'm having a whole host of problems with an external hard drive that was working just fine a couple of hours ago. I've had this problem before once, and that was about 3 months ago, here's what I documented: So a couple of hours ago I turned off all my computers and shut off the power to all my devices in my room, then went and turned the power off at the main switch so I could change an outlet. A couple hours later, after I've already slowly turned everything back on, I go to my xbox to try and watch a movie and it can't seem to list any of the movies I've got. So I go to my desktop to find that my external hard drive isn't there.. even though it's on and connected. It's also stationary and hidden behind something so there's not a whole lot of tampering/physical wear to that external. I plug it into my laptop to try and see what's going on. It starts making this endless loud screeching noise. None of that clicking that's usually associated with hd damage. It's not listed in my computers, and it shows up in Disk Management as "uninitialized" asking me to choose between two different partition types. After carefully disconnecting it and connecting it back, it asks me to format it, which I cancel. I start googling about my issue, starting to accept the situation, torn as hell and helpless and just about ready to toss the thing. Suddenly the screeching stops, after almost 45 minutes of it going, and Disk Management lists the drive as "Online" and "Healthy". Explorer pops up with all my files! I'm still being really careful with it and weary and treating it as though it's in fragile shape. I've downloaded some S.M.A.R.T. software to read the values and everything is listed as "OK" . No reallocated sectors, no read errors, no seek errors. I also ran a quick self-test, which completed without error. Everything seems fine. It looks to be a perfectly healthy external hard drive. So what the hell was that about? Was it doing some sort of maintenance or self-test? How am I supposed to tell the difference? I would've undoubtedly killed the drive for sure if had it gone on a bit longer. I've got the same problem now, with one exception: it doesn't magically reappear after the screeching stops. Occasionally I manage to get some S.M.A.R.T. diagnostics information, which basically reads everything as fine. The only problem is that my HD isn't initializing (so I can't access anything in it). I'm able to successfully run a quick smart test but not an extended one (I've only tried it once but got conflicting indications as to whether it was actually making any progress or not (was stuck on Random read test). So, final question (if all else fails): Could the hard drive enclosure be failing rather than the HDD? Is this a likely possibility at all? How would I know?

    Read the article

  • Hoster not fulfilling contract: how to get money back?

    - by plua
    For several years, we have as a small webdesign company rented a dedicated server at a large hosting provider. They had several support levels. When we signed up for this, we had very limited in-house knowledge about server maintenance, and were very worried about the security of our server. We therefore took one of the more expensive support packages. An important aspect in this were these claims: [PROVIDER] verifies the availability of the latest security updates and sends you a notification to see if you are interested to have them installed [PROVIDER] verifies the availability of the latest supported software updates and sends you a notification to see if you are interested to have them installed These items were clearly stated on their website as being part of the advantage of this package.; With not enough knowledge about installing and updating such software on a Linux server, we decided to go for this package. We paid a premium of $50 per month over the maintenance package that is next in line ($100 vs $50). Over the years, we have paid several thousand dollars for this service. Then came the moment that I learned more and more about server management. And I found out step by step that our server was horrendously outdated! We had an OS that was hardly updated, our anti-virus was not working because it needed certain more recent packages on the OS, and in general there were a whole bunch of security vulnerabilities and fixes that were lacking. Shocked, I wrote the provider. Turns out, they decided unilaterally that they would not send out any notifications to clients because clients would get too many e-mails. This is a quote from their explanation: [...] We have decided not to spam its clients with OS and security updates and only install them whenever asked by the client I was shocked! They had never mentioned that they would drop this service, and in fact the claims about updating their clients through e-mail was still on their website, after they apparently stopped doing this years ago! Upon finding this out, I requested they refund all that we have paid as a premium over the other package, and make it available as future credit with their own company. I thought this was a very reasonable request. However, they said they would only go back one year and provide credit for this one year. Mails went back and forth, but they were not willing to give credit for the whole period, which I felt I was entitled to. So ultimately I left the hosting company, and filed a complaint with the BBB a while ago. Now, I am not the kind of person who runs to a lawyer for any minor thing, but in this case I am really considering taking action. I have been paying for years for a service I did not receive (the premium package had a few other pluses, but we took it primarily for these two points, and I can prove that we did not use the other benefits). For our small company the hosting costs were a very large part of our budget, and I feel it is very unfair how this large provider just does not care about not fulfilling its obligations. So my question is: what action should I take? Is a lawyer the only next step, or are there other suggestions? And am I right here to claim this money, or are they right that there is some sort of statue of limitations on such claims? Any feedback is appreciated.

    Read the article

  • WiX 3 Tutorial: Generating file/directory fragments with Heat.exe

    - by Mladen Prajdic
    In previous posts I’ve shown you our SuperForm test application solution structure and how the main wxs and wxi include file look like. In this post I’ll show you how to automate inclusion of files to install into your build process. For our SuperForm application we have a single exe to install. But in the real world we have 10s or 100s of different files from dll’s to resource files like pictures. It all depends on what kind of application you’re building. Writing a directory structure for so many files by hand is out of the question. What we need is an automated way to create this structure. Enter Heat.exe. Heat is a command line utility to harvest a file, directory, Visual Studio project, IIS website or performance counters. You might ask what harvesting means? Harvesting is converting a source (file, directory, …) into a component structure saved in a WiX fragment (a wxs) file. There are 2 options you can use: Create a static wxs fragment with Heat and include it in your project. The pro of this is that you can add or remove components by hand. The con is that you have to do the pro part by hand. Automation always beats manual labor. Run heat command line utility in a pre-build event of your WiX project. I prefer this way. By always recreating the whole fragment you don’t have to worry about missing any new files you add. The con of this is that you’ll include files that you otherwise might not want to. There is no perfect solution so pick one and deal with it. I prefer using the second way. A neat way of overcoming the con of the second option is to have a post-build event on your main application project (SuperForm.MainApp in our case) to copy the files needed to be installed in a special location and have the Heat.exe read them from there. I haven’t set this up for this tutorial and I’m simply including all files from the default SuperForm.MainApp \bin directory. Remember how we created a System Environment variable called SuperFormFilesDir? This is where we’ll use it for the first time. The command line text that you have to put into the pre-build event of your WiX project looks like this: "$(WIX)bin\heat.exe" dir "$(SuperFormFilesDir)" -cg SuperFormFiles -gg -scom -sreg -sfrag -srd -dr INSTALLLOCATION -var env.SuperFormFilesDir -out "$(ProjectDir)Fragments\FilesFragment.wxs" After you install WiX you’ll get the WIX environment variable. In the pre/post-build events environment variables are referenced like this: $(WIX). By using this you don’t have to think about the installation path of the WiX. Remember: for 32 bit applications Program files folder is named differently between 32 and 64 bit systems. $(ProjectDir) is obviously the path to your project and is a Visual Studio built in variable. You can view all Heat.exe options by running it without parameters but I’ll explain some that stick out the most. dir "$(SuperFormFilesDir)": tell Heat to harvest the whole directory at the set location. That is the location we’ve set in our System Environment variable. –cg SuperFormFiles: the name of the Component group that will be created. This name is included in out Feature tag as is seen in the previous post. -dr INSTALLLOCATION: the directory reference this fragment will fall under. You can see the top level directory structure in the previous post. -var env.SuperFormFilesDir: the name of the variable that will replace the SourceDir text that would otherwise appear in the fragment file. -out "$(ProjectDir)Fragments\FilesFragment.wxs": the full path and name under which the fragment file will be saved. If you have source control you have to include the FilesFragment.wxs into your project but remove its source control binding. The auto generated FilesFragment.wxs for our test app looks like this: <?xml version="1.0" encoding="utf-8"?><Wix xmlns="http://schemas.microsoft.com/wix/2006/wi"> <Fragment> <ComponentGroup Id="SuperFormFiles"> <ComponentRef Id="cmp5BB40DB822CAA7C5295227894A07502E" /> <ComponentRef Id="cmpCFD331F5E0E471FC42A1334A1098E144" /> <ComponentRef Id="cmp4614DD03D8974B7C1FC39E7B82F19574" /> <ComponentRef Id="cmpDF166522884E2454382277128BD866EC" /> </ComponentGroup> </Fragment> <Fragment> <DirectoryRef Id="INSTALLLOCATION"> <Component Id="cmp5BB40DB822CAA7C5295227894A07502E" Guid="{117E3352-2F0C-4E19-AD96-03D354751B8D}"> <File Id="filDCA561ABF8964292B6BC0D0726E8EFAD" KeyPath="yes" Source="$(env.SuperFormFilesDir)\SuperForm.MainApp.exe" /> </Component> <Component Id="cmpCFD331F5E0E471FC42A1334A1098E144" Guid="{369A2347-97DD-45CA-A4D1-62BB706EA329}"> <File Id="filA9BE65B2AB60F3CE41105364EDE33D27" KeyPath="yes" Source="$(env.SuperFormFilesDir)\SuperForm.MainApp.pdb" /> </Component> <Component Id="cmp4614DD03D8974B7C1FC39E7B82F19574" Guid="{3443EBE2-168F-4380-BC41-26D71A0DB1C7}"> <File Id="fil5102E75B91F3DAFA6F70DA57F4C126ED" KeyPath="yes" Source="$(env.SuperFormFilesDir)\SuperForm.MainApp.vshost.exe" /> </Component> <Component Id="cmpDF166522884E2454382277128BD866EC" Guid="{0C0F3D18-56EB-41FE-B0BD-FD2C131572DB}"> <File Id="filF7CA5083B4997E1DEC435554423E675C" KeyPath="yes" Source="$(env.SuperFormFilesDir)\SuperForm.MainApp.vshost.exe.manifest" /> </Component> </DirectoryRef> </Fragment></Wix> The $(env.SuperFormFilesDir) will be replaced at build time with the directory where the files to be installed are located. There is nothing too complicated about this. In the end it turns out that this sort of automation is great! There are a few other ways that Heat.exe can compose the wxs file but this is the one I prefer. It just seems the clearest. Play with its options to see what can it do. It’s one awesome little tool.   WiX 3 tutorial by Mladen Prajdic navigation WiX 3 Tutorial: Solution/Project structure and Dev resources WiX 3 Tutorial: Understanding main wxs and wxi file WiX 3 Tutorial: Generating file/directory fragments with Heat.exe

    Read the article

  • Oracle Insurance Unveils Next Generation of Enterprise Document Automation: Oracle Documaker Enterprise Edition

    - by helen.pitts(at)oracle.com
    Oracle today announced the introduction of Oracle Documaker Enterprise Edition, the next generation of the company's market-leading Enterprise Document Automation (EDA) solution for dynamically creating, managing and delivering adaptive enterprise communications across multiple channels. "Insurers and other organizations need enterprise document automation that puts the power to manage the complete document lifecycle in the hands of the business user," said Srini Venkatasanthanam, vice president, Product Strategy, Oracle Insurancein the press release. "Built with features such as rules-based configurability and interactive processing, Oracle Documaker Enterprise Edition makes possible an adaptive approach to enterprise document automation - documents when, where and in the form they're needed." Key enhancements in Oracle Documaker Enterprise Edition include: Documaker Interactive, the newly renamed and redesigned Web-based iDocumaker module. Documaker Interactive enables users to quickly and interactively create and assemble compliant communications such as policy and claims correspondence directly from their desktops. Users benefits from built-in accelerators and rules-based configurability, pre-configured content as well as embedded workflow leveraging Oracle BPEL Process Manager. Documaker Documaker Factory, which helps enterprises reduce cost and improve operational efficiency through better management of their enterprise publishing operations. Dashboards, analytics, reporting and an administrative console provide insurers with greater insight and centralized control over document production allowing them to better adapt their resources based on business demands. Other enhancements include: enhanced business user empowerment; additional multi-language localization capabilities; and benefits from the use of powerful Oracle technologies such as the Oracle Application Development Framework for all interfaces and Oracle Universal Content Management (Oracle UCM) for enterprise content management. Drive Competitive Advantage and Growth: Deb Smallwood, founder of SMA Strategy Meets Action, a leading industry insurance analyst consulting firm and co-author of 3CM in Insurance: Customer Communications and Content Management published last month, noted in the press release that "maximum value can be gained from investments when Enterprise Document Automation (EDA) is viewed holistically and all forms of communication and all types of information are integrated across the entire enterprise. "Insurers that choose an approach that takes all communications, both structured and unstructured data, coming into the company from a wide range of channels, and then create seamless flows of information will have a real competitive advantage," Smallwood said. "This capability will soon become essential for selling, servicing, and ultimately driving growth through new business and retention." Learn More: Click here to watch a short flash demo that demonstrates the real business value offered by Oracle Documaker Enterprise Edition. You can also see how an insurance company can use Oracle Documaker Enterprise Edition to dynamically create, manage and publish adaptive enterprise content throughout the insurance business lifecycle for delivery across multiple channels by visiting Alamere Insurance, a fictional model insurance company created by Oracle to showcase how Oracle applications can be leveraged within the insurance enterprise. Meet Our Newest Oracle Insurance Blogger: I'm pleased to introduce our newest Oracle Insurance blogger, Susanne Hale. Susanne, who manages product marketing for Oracle Insurance EDA solutions, will be sharing insights about this topic along with examples of how our customers are transforming their enterprise communications using Oracle Documaker Enterprise Edition in future Oracle Insurance blog entries. Helen Pitts is senior product marketing manager for Oracle Insurance.

    Read the article

  • Bargain Hunter Round Up – Kicking Off The E-Commerce Holiday Season

    - by Jeri Kelley
    Everyone has a different way to tackle holiday shopping – Black Friday, Small Business Saturday, Cyber Monday, some have it done months in advance, and others wait until the very last minute.   For me, I’m not big into massive crowds so online shopping to the rescue.   Others thrive on the energy of being in the stores on the busiest shopping day of the year.  With last weekend marking the official kick-off to the holiday season, I thought I’d provide a round up of what’s trending:   Online numbers are looking up: According to comScore, for the holiday season-to-date, $16.4 billion has been spent online, marking a 16-percent increase versus the corresponding days last year. Thanksgiving Day – Why wait until Black Friday or Cyber Monday: Online shopping on Thanksgiving Day also increased, totaling $633 million in receipts, a 32 percent increase over Thanksgiving 2011 Black Friday – More than just in-store: Bargain hunters spent $1.042 billion online the day after Thanksgiving, a 26 percent increase of last year's Black Friday, according to new figures released today by market analyst ComScore Cyber Monday Week: Cyber Monday reached $1.465 billion in online spending, up 17 percent versus year ago, representing the heaviest online spending day in history and the second day this season (in addition to Black Friday) to surpass $1 billion in sales                 Cyber Monday is now being dubbed Cyber Week:  “The annual event is increasingly becoming Cyber Week instead of a one-day event as retailers open their arms for Americans who prefer to avoid crowds and compare prices online.” But, Cyber Monday continues its importance, driving a nearly 22% increase in year-over-year (YoY) online sales. Monday sales beat Sunday, the next highest day by a margin of 26.7%. Mobile shopping continues to rise: ChannelAdvisor that said mobile shopping made up 32% of all online spending over the Black Friday weekend Mobile devices were a key part of the online shopping craziness that was November 26th.  Sales from smartphones and tablets doubled this year. I n tablets the growth was 110% and in smartphones - 100% Mobile bar code scans on Black Friday increased 50 percent, according to a report from ScanLife For more on how you can be ready for the holiday season, check out my blog post on commerce strategies for the holidays.

    Read the article

  • Developer’s Life – Every Developer is a Captain America

    - by Pinal Dave
    Captain America was first created as a comic book character in the 1940’s as a way to boost morale during World War II.  Aimed at a children’s audience, his legacy faded away when the war ended.  However, he has recently has a major reboot to become a popular movie character that deals with modern issues. When Captain America was first written, there was no such thing as a developer, programmer or a computer (the way we think of them, anyway).  Despite these limitations, I think there are still a lot of ways that modern Captain America is like modern developers. So how are developers like Captain America? Well, read on my list of reasons. Take on Big Projects Captain America isn’t afraid to take on big projects – and takes responsibility when the project is co-opted by the evil organization HYDRA.  Developers may not have super villains out there corrupting their work, but they know to keep on top of their projects and own what they do. Elderly Wisdom Steve Rogers, Captain America’s alter ego, was frozen in ice for decades, and brought back to life to solve problems. Developers can learn from this by respecting the opinions of their elders – technology is an ever-changing market, but the old-timers still have a few tricks up their sleeves! Don’t be Afraid of Change Don’t be afraid of change.  Captain America woke up to find the world he was accustomed to is now completely different.  He might have even felt his skills were no longer necessary.  He, and developers, know that everyone has their place in a team, though.  If you try your best, you will make it work. Fight Your Own Battle Sometimes you have to make it on your own.  Captain America is an integral part of the Avengers, but in his own movies, the other superheroes aren’t around to back him up.  Developers, too, must learn to work both within and with out a team. Solid Integrity One of Captain America’s greatest qualities is his integrity.  His determine to do what is right, keep his word, and act honestly earns him mockery from some of the less-savory characters – even “good guys” like Iron Man.  Developers, and everyone else, need to develop the strength of character to keep their integrity.  No matter your walk of life, there will be tempting obstacles.  Think of Captain America, and say “no.” There is a lot for all of us to learn from Captain America, to take away in our own lives, and admire in those who display it – I am specifically thinking of developers.  If you are enjoying this series as much as I am, please let me know who else you would like to see featured. Reference: Pinal Dave (http://blog.sqlauthority.com)Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL Tagged: Developer, Superhero

    Read the article

  • Displaying an image on a LED matrix with a Netduino

    - by Bertrand Le Roy
    In the previous post, we’ve been flipping bits manually on three ports of the Netduino to simulate the data, clock and latch pins that a shift register expected. We did all that in order to control one line of a LED matrix and create a simple Knight Rider effect. It was rightly pointed out in the comments that the Netduino has built-in knowledge of the sort of serial protocol that this shift register understands through a feature called SPI. That will of course make our code a whole lot simpler, but it will also make it a whole lot faster: writing to the Netduino ports is actually not that fast, whereas SPI is very, very fast. Unfortunately, the Netduino documentation for SPI is severely lacking. Instead, we’ve been reliably using the documentation for the Fez, another .NET microcontroller. To send data through SPI, we’ll just need  to move a few wires around and update the code. SPI uses pin D11 for writing, pin D12 for reading (which we won’t do) and pin D13 for the clock. The latch pin is a parameter that can be set by the user. This is very close to the wiring we had before (data on D11, clock on D12 and latch on D13). We just have to move the latch from D13 to D10, and the clock from D12 to D13. The code that controls the shift register has slimmed down considerably with that change. Here is the new version, which I invite you to compare with what we had before: public class ShiftRegister74HC595 { protected SPI Spi; public ShiftRegister74HC595(Cpu.Pin latchPin) : this(latchPin, SPI.SPI_module.SPI1) { } public ShiftRegister74HC595(Cpu.Pin latchPin, SPI.SPI_module spiModule) { var spiConfig = new SPI.Configuration( SPI_mod: spiModule, ChipSelect_Port: latchPin, ChipSelect_ActiveState: false, ChipSelect_SetupTime: 0, ChipSelect_HoldTime: 0, Clock_IdleState: false, Clock_Edge: true, Clock_RateKHz: 1000 ); Spi = new SPI(spiConfig); } public void Write(byte buffer) { Spi.Write(new[] {buffer}); } } All we have to do here is configure SPI. The write method couldn’t be any simpler. Everything is now handled in hardware by the Netduino. We set the frequency to 1MHz, which is largely sufficient for what we’ll be doing, but it could potentially go much higher. The shift register addresses the columns of the matrix. The rows are directly wired to ports D0 to D7 of the Netduino. The code writes to only one of those eight lines at a time, which will make it fast enough. The way an image is displayed is that we light the lines one after the other so fast that persistence of vision will give the illusion of a stable image: foreach (var bitmap in matrix.MatrixBitmap) { matrix.OnRow(row, bitmap, true); matrix.OnRow(row, bitmap, false); row++; } Now there is a twist here: we need to run this code as fast as possible in order to display the image with as little flicker as possible, but we’ll eventually have other things to do. In other words, we need the code driving the display to run in the background, except when we want to change what’s being displayed. Fortunately, the .NET Micro Framework supports multithreading. In our implementation, we’ve added an Initialize method that spins a new thread that is tied to the specific instance of the matrix it’s being called on. public LedMatrix Initialize() { DisplayThread = new Thread(() => DoDisplay(this)); DisplayThread.Start(); return this; } I quite like this way to spin a thread. As you may know, there is another, built-in way to contextualize a thread by passing an object into the Start method. For the method to work, the thread must have been constructed with a ParameterizedThreadStart delegate, which takes one parameter of type object. I like to use object as little as possible, so instead I’m constructing a closure with a Lambda, currying it with the current instance. This way, everything remains strongly-typed and there’s no casting to do. Note that this method would extend perfectly to several parameters. Of note as well is the return value of Initialize, a common technique to add some fluency to the API and enabling the matrix to be instantiated and initialized in a single line: using (var matrix = new LedMS88SR74HC595().Initialize()) The “using” in the previous line is because we have implemented IDisposable so that the matrix kills the thread and clears the display when the user code is done with it: public void Dispose() { Clear(); DisplayThread.Abort(); } Thanks to the multi-threaded version of the matrix driver class, we can treat the display as a simple bitmap with a very synchronous programming model: matrix.Set(someimage); while (button.Read()) { Thread.Sleep(10); } Here, the call into Set returns immediately and from the moment the bitmap is set, the background display thread will constantly continue refreshing no matter what happens in the main thread. That enables us to wait or read a button’s port on the main thread knowing that the current image will continue displaying unperturbed and without requiring manual refreshing. We’ve effectively hidden the implementation of the display behind a convenient, synchronous-looking API. Pretty neat, eh? Before I wrap up this post, I want to talk about one small caveat of using SPI rather than driving the shift register directly: when we got to the point where we could actually display images, we noticed that they were a mirror image of what we were sending in. Oh noes! Well, the reason for it is that SPI is sending the bits in a big-endian fashion, in other words backwards. Now sure you could fix that in software by writing some bit-level code to reverse the bits we’re sending in, but there is a far more efficient solution than that. We are doing hardware here, so we can simply reverse the order in which the outputs of the shift register are connected to the columns of the matrix. That’s switching 8 wires around once, as compared to doing bit operations every time we send a line to display. All right, so bringing it all together, here is the code we need to write to display two images in succession, separated by a press on the board’s button: var button = new InputPort(Pins.ONBOARD_SW1, false, Port.ResistorMode.Disabled); using (var matrix = new LedMS88SR74HC595().Initialize()) { // Oh, prototype is so sad! var sad = new byte[] { 0x66, 0x24, 0x00, 0x18, 0x00, 0x3C, 0x42, 0x81 }; DisplayAndWait(sad, matrix, button); // Let's make it smile! var smile = new byte[] { 0x42, 0x18, 0x18, 0x81, 0x7E, 0x3C, 0x18, 0x00 }; DisplayAndWait(smile, matrix, button); } And here is a video of the prototype running: The prototype in action I’ve added an artificial delay between the display of each row of the matrix to clearly show what’s otherwise happening very fast. This way, you can clearly see each of the two images being displayed line by line. Next time, we’ll do no hardware changes, focusing instead on building a nice programming model for the matrix, with sprites, text and hardware scrolling. Fun stuff. By the way, can any of my reader guess where we’re going with all that? The code for this prototype can be downloaded here: http://weblogs.asp.net/blogs/bleroy/Samples/NetduinoLedMatrixDriver.zip

    Read the article

  • How do I get an Enter USB TV Box TV tuner aka Gadmei UTV302 to work?

    - by Subhash
    Has anyone had any success in using the Enter USB TV Box from Enter Multimedia? It comes bundled with software that works in Windows. I have had no luck using it in Ubuntu 10.10. Update 1 Here is the output from lsusb Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 003: ID 093a:2510 Pixart Imaging, Inc. Optical Mouse Bus 004 Device 002: ID 046d:c312 Logitech, Inc. DeLuxe 250 Keyboard Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 006: ID 1f71:3301 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub I can't find the Enter USB TV Box listed in this. In the dmesg tail command, I found something that seems to be related to the card: usb 1-5: new high speed USB device using ehci_hcd and address 6 usb 1-5: config 1 interface 0 altsetting 1 bulk endpoint 0x83 has invalid maxpacket 256 Update 2 From Windows I learned that this USB TV tuner uses some chipset from Gadmei corporation. All computer stores in India sell Enter USB TV Box if you ask for an USB TV tuner. No other brand seems to be interested in this market. Update 3 I learned that this TV tuner is rebranded version of Gadmei UTV302 (USB TV Tuner Box). Update 4 I tried adding em28xx as the chipset (as suggested by user BOBBO below) for the tuner but that did not work. I went back to my Pinnacle PCTV internal card. I don't think the tuner referred by UbuntuForums (Gadmei UTV 330) and the tuner that I have (Gadmei UTV 302) are the same. My USB tuner is several times bigger. My tuner seems to be a newer device with a newer tuner chip. I will submit details of this device to the LinuxTV developers this weekend. Update 5 I opened the tuner box and found that it uses a tuner from a Chinese company - Tenas. Model is TNF 8022-DFA. Update 6 Tuner chip specs (retrived from supplier directory) for Tenas TNF 8022-DFA. Supply voltage: true 5V device(low power dissipation) Control system: I2C bus control of tuning, address selection Tuning system: PLL controlled tuning Receiving system: system PAL D/K,IF(Intermediate Frequency): 38MHz Receiving channels: full frequency range from channel DS1 (49.75MHz) to channel DS57 (863.25MHz); Use Texas Instruments SN761678 IC solution, with mini install size Update 7 Reverse side of the circuit board. Picture of the TV tuner

    Read the article

  • Serious about Embedded: Java Embedded @ JavaOne 2012

    - by terrencebarr
    It bears repeating: More than ever, the Java platform is the best technology for many embedded use cases. Java’s platform independence, high level of functionality, security, and developer productivity address the key pain points in building embedded solutions. Transitioning from 16 to 32 bit or even 64 bit? Need to support multiple architectures and operating systems with a single code base? Want to scale on multi-core systems? Require a proven security model? Dynamically deploy and manage software on your devices? Cut time to market by leveraging code, expertise, and tools from a large developer ecosystem? Looking for back-end services, integration, and management? The Java platform has got you covered. Java already powers around 10 billion devices worldwide, with traditional desktops and servers being only a small portion of that. And the ‘Internet of Things‘ is just really starting to explode … it is estimated that within five years, intelligent and connected embedded devices will outnumber desktops and mobile phones combined, and will generate the majority of the traffic on the Internet. Is your platform and services strategy ready for the coming disruptions and opportunities? It should come as no surprise that Oracle is keenly focused on Java for Embedded. At JavaOne 2012 San Francisco the dedicated track for Java ME, Java Card, and Embedded keeps growing, with 52 sessions, tutorials, Hands-on-Labs, and BOFs scheduled for this track alone, plus keynotes, demos, booths, and a variety of other embedded content. To further prove Oracle’s commitment, in 2012 for the first time there will be a dedicated sub-conference focused on the business aspects of embedded Java: Java Embedded @ JavaOne. This conference will run for two days in parallel to JavaOne in San Francisco, will have its own business-oriented track and content, and targets C-level executives, architects, business leaders, and decision makers. Registration and Call For Papers for Java Embedded @ JavaOne are now live. We expect a lot of interest in this new event and space is limited, so be sure to submit your paper and register soon. Hope to see you there! Cheers, – Terrence Filed under: Mobile & Embedded Tagged: ARM, Call for Papers, Embedded Java, Java Embedded, Java Embedded @ JavaOne, Java ME, Java SE Embedded, Java SE for Embedded, JavaOne San Francisco, PowerPC

    Read the article

  • Toorcon14

    - by danx
    Toorcon 2012 Information Security Conference San Diego, CA, http://www.toorcon.org/ Dan Anderson, October 2012 It's almost Halloween, and we all know what that means—yes, of course, it's time for another Toorcon Conference! Toorcon is an annual conference for people interested in computer security. This includes the whole range of hackers, computer hobbyists, professionals, security consultants, press, law enforcement, prosecutors, FBI, etc. We're at Toorcon 14—see earlier blogs for some of the previous Toorcon's I've attended (back to 2003). This year's "con" was held at the Westin on Broadway in downtown San Diego, California. The following are not necessarily my views—I'm just the messenger—although I could have misquoted or misparaphrased the speakers. Also, I only reviewed some of the talks, below, which I attended and interested me. MalAndroid—the Crux of Android Infections, Aditya K. Sood Programming Weird Machines with ELF Metadata, Rebecca "bx" Shapiro Privacy at the Handset: New FCC Rules?, Valkyrie Hacking Measured Boot and UEFI, Dan Griffin You Can't Buy Security: Building the Open Source InfoSec Program, Boris Sverdlik What Journalists Want: The Investigative Reporters' Perspective on Hacking, Dave Maas & Jason Leopold Accessibility and Security, Anna Shubina Stop Patching, for Stronger PCI Compliance, Adam Brand McAfee Secure & Trustmarks — a Hacker's Best Friend, Jay James & Shane MacDougall MalAndroid—the Crux of Android Infections Aditya K. Sood, IOActive, Michigan State PhD candidate Aditya talked about Android smartphone malware. There's a lot of old Android software out there—over 50% Gingerbread (2.3.x)—and most have unpatched vulnerabilities. Of 9 Android vulnerabilities, 8 have known exploits (such as the old Gingerbread Global Object Table exploit). Android protection includes sandboxing, security scanner, app permissions, and screened Android app market. The Android permission checker has fine-grain resource control, policy enforcement. Android static analysis also includes a static analysis app checker (bouncer), and a vulnerablity checker. What security problems does Android have? User-centric security, which depends on the user to grant permission and make smart decisions. But users don't care or think about malware (the're not aware, not paranoid). All they want is functionality, extensibility, mobility Android had no "proper" encryption before Android 3.0 No built-in protection against social engineering and web tricks Alternative Android app markets are unsafe. Simply visiting some markets can infect Android Aditya classified Android Malware types as: Type A—Apps. These interact with the Android app framework. For example, a fake Netflix app. Or Android Gold Dream (game), which uploads user files stealthy manner to a remote location. Type K—Kernel. Exploits underlying Linux libraries or kernel Type H—Hybrid. These use multiple layers (app framework, libraries, kernel). These are most commonly used by Android botnets, which are popular with Chinese botnet authors What are the threats from Android malware? These incude leak info (contacts), banking fraud, corporate network attacks, malware advertising, malware "Hackivism" (the promotion of social causes. For example, promiting specific leaders of the Tunisian or Iranian revolutions. Android malware is frequently "masquerated". That is, repackaged inside a legit app with malware. To avoid detection, the hidden malware is not unwrapped until runtime. The malware payload can be hidden in, for example, PNG files. Less common are Android bootkits—there's not many around. What they do is hijack the Android init framework—alteering system programs and daemons, then deletes itself. For example, the DKF Bootkit (China). Android App Problems: no code signing! all self-signed native code execution permission sandbox — all or none alternate market places no robust Android malware detection at network level delayed patch process Programming Weird Machines with ELF Metadata Rebecca "bx" Shapiro, Dartmouth College, NH https://github.com/bx/elf-bf-tools @bxsays on twitter Definitions. "ELF" is an executable file format used in linking and loading executables (on UNIX/Linux-class machines). "Weird machine" uses undocumented computation sources (I think of them as unintended virtual machines). Some examples of "weird machines" are those that: return to weird location, does SQL injection, corrupts the heap. Bx then talked about using ELF metadata as (an uintended) "weird machine". Some ELF background: A compiler takes source code and generates a ELF object file (hello.o). A static linker makes an ELF executable from the object file. A runtime linker and loader takes ELF executable and loads and relocates it in memory. The ELF file has symbols to relocate functions and variables. ELF has two relocation tables—one at link time and another one at loading time: .rela.dyn (link time) and .dynsym (dynamic table). GOT: Global Offset Table of addresses for dynamically-linked functions. PLT: Procedure Linkage Tables—works with GOT. The memory layout of a process (not the ELF file) is, in order: program (+ heap), dynamic libraries, libc, ld.so, stack (which includes the dynamic table loaded into memory) For ELF, the "weird machine" is found and exploited in the loader. ELF can be crafted for executing viruses, by tricking runtime into executing interpreted "code" in the ELF symbol table. One can inject parasitic "code" without modifying the actual ELF code portions. Think of the ELF symbol table as an "assembly language" interpreter. It has these elements: instructions: Add, move, jump if not 0 (jnz) Think of symbol table entries as "registers" symbol table value is "contents" immediate values are constants direct values are addresses (e.g., 0xdeadbeef) move instruction: is a relocation table entry add instruction: relocation table "addend" entry jnz instruction: takes multiple relocation table entries The ELF weird machine exploits the loader by relocating relocation table entries. The loader will go on forever until told to stop. It stores state on stack at "end" and uses IFUNC table entries (containing function pointer address). The ELF weird machine, called "Brainfu*k" (BF) has: 8 instructions: pointer inc, dec, inc indirect, dec indirect, jump forward, jump backward, print. Three registers - 3 registers Bx showed example BF source code that implemented a Turing machine printing "hello, world". More interesting was the next demo, where bx modified ping. Ping runs suid as root, but quickly drops privilege. BF modified the loader to disable the library function call dropping privilege, so it remained as root. Then BF modified the ping -t argument to execute the -t filename as root. It's best to show what this modified ping does with an example: $ whoami bx $ ping localhost -t backdoor.sh # executes backdoor $ whoami root $ The modified code increased from 285948 bytes to 290209 bytes. A BF tool compiles "executable" by modifying the symbol table in an existing ELF executable. The tool modifies .dynsym and .rela.dyn table, but not code or data. Privacy at the Handset: New FCC Rules? "Valkyrie" (Christie Dudley, Santa Clara Law JD candidate) Valkyrie talked about mobile handset privacy. Some background: Senator Franken (also a comedian) became alarmed about CarrierIQ, where the carriers track their customers. Franken asked the FCC to find out what obligations carriers think they have to protect privacy. The carriers' response was that they are doing just fine with self-regulation—no worries! Carriers need to collect data, such as missed calls, to maintain network quality. But carriers also sell data for marketing. Verizon sells customer data and enables this with a narrow privacy policy (only 1 month to opt out, with difficulties). The data sold is not individually identifiable and is aggregated. But Verizon recommends, as an aggregation workaround to "recollate" data to other databases to identify customers indirectly. The FCC has regulated telephone privacy since 1934 and mobile network privacy since 2007. Also, the carriers say mobile phone privacy is a FTC responsibility (not FCC). FTC is trying to improve mobile app privacy, but FTC has no authority over carrier / customer relationships. As a side note, Apple iPhones are unique as carriers have extra control over iPhones they don't have with other smartphones. As a result iPhones may be more regulated. Who are the consumer advocates? Everyone knows EFF, but EPIC (Electrnic Privacy Info Center), although more obsecure, is more relevant. What to do? Carriers must be accountable. Opt-in and opt-out at any time. Carriers need incentive to grant users control for those who want it, by holding them liable and responsible for breeches on their clock. Location information should be added current CPNI privacy protection, and require "Pen/trap" judicial order to obtain (and would still be a lower standard than 4th Amendment). Politics are on a pro-privacy swing now, with many senators and the Whitehouse. There will probably be new regulation soon, and enforcement will be a problem, but consumers will still have some benefit. Hacking Measured Boot and UEFI Dan Griffin, JWSecure, Inc., Seattle, @JWSdan Dan talked about hacking measured UEFI boot. First some terms: UEFI is a boot technology that is replacing BIOS (has whitelisting and blacklisting). UEFI protects devices against rootkits. TPM - hardware security device to store hashs and hardware-protected keys "secure boot" can control at firmware level what boot images can boot "measured boot" OS feature that tracks hashes (from BIOS, boot loader, krnel, early drivers). "remote attestation" allows remote validation and control based on policy on a remote attestation server. Microsoft pushing TPM (Windows 8 required), but Google is not. Intel TianoCore is the only open source for UEFI. Dan has Measured Boot Tool at http://mbt.codeplex.com/ with a demo where you can also view TPM data. TPM support already on enterprise-class machines. UEFI Weaknesses. UEFI toolkits are evolving rapidly, but UEFI has weaknesses: assume user is an ally trust TPM implicitly, and attached to computer hibernate file is unprotected (disk encryption protects against this) protection migrating from hardware to firmware delays in patching and whitelist updates will UEFI really be adopted by the mainstream (smartphone hardware support, bank support, apathetic consumer support) You Can't Buy Security: Building the Open Source InfoSec Program Boris Sverdlik, ISDPodcast.com co-host Boris talked about problems typical with current security audits. "IT Security" is an oxymoron—IT exists to enable buiness, uptime, utilization, reporting, but don't care about security—IT has conflict of interest. There's no Magic Bullet ("blinky box"), no one-size-fits-all solution (e.g., Intrusion Detection Systems (IDSs)). Regulations don't make you secure. The cloud is not secure (because of shared data and admin access). Defense and pen testing is not sexy. Auditors are not solution (security not a checklist)—what's needed is experience and adaptability—need soft skills. Step 1: First thing is to Google and learn the company end-to-end before you start. Get to know the management team (not IT team), meet as many people as you can. Don't use arbitrary values such as CISSP scores. Quantitive risk assessment is a myth (e.g. AV*EF-SLE). Learn different Business Units, legal/regulatory obligations, learn the business and where the money is made, verify company is protected from script kiddies (easy), learn sensitive information (IP, internal use only), and start with low-hanging fruit (customer service reps and social engineering). Step 2: Policies. Keep policies short and relevant. Generic SANS "security" boilerplate policies don't make sense and are not followed. Focus on acceptable use, data usage, communications, physical security. Step 3: Implementation: keep it simple stupid. Open source, although useful, is not free (implementation cost). Access controls with authentication & authorization for local and remote access. MS Windows has it, otherwise use OpenLDAP, OpenIAM, etc. Application security Everyone tries to reinvent the wheel—use existing static analysis tools. Review high-risk apps and major revisions. Don't run different risk level apps on same system. Assume host/client compromised and use app-level security control. Network security VLAN != segregated because there's too many workarounds. Use explicit firwall rules, active and passive network monitoring (snort is free), disallow end user access to production environment, have a proxy instead of direct Internet access. Also, SSL certificates are not good two-factor auth and SSL does not mean "safe." Operational Controls Have change, patch, asset, & vulnerability management (OSSI is free). For change management, always review code before pushing to production For logging, have centralized security logging for business-critical systems, separate security logging from administrative/IT logging, and lock down log (as it has everything). Monitor with OSSIM (open source). Use intrusion detection, but not just to fulfill a checkbox: build rules from a whitelist perspective (snort). OSSEC has 95% of what you need. Vulnerability management is a QA function when done right: OpenVas and Seccubus are free. Security awareness The reality is users will always click everything. Build real awareness, not compliance driven checkbox, and have it integrated into the culture. Pen test by crowd sourcing—test with logging COSSP http://www.cossp.org/ - Comprehensive Open Source Security Project What Journalists Want: The Investigative Reporters' Perspective on Hacking Dave Maas, San Diego CityBeat Jason Leopold, Truthout.org The difference between hackers and investigative journalists: For hackers, the motivation varies, but method is same, technological specialties. For investigative journalists, it's about one thing—The Story, and they need broad info-gathering skills. J-School in 60 Seconds: Generic formula: Person or issue of pubic interest, new info, or angle. Generic criteria: proximity, prominence, timeliness, human interest, oddity, or consequence. Media awareness of hackers and trends: journalists becoming extremely aware of hackers with congressional debates (privacy, data breaches), demand for data-mining Journalists, use of coding and web development for Journalists, and Journalists busted for hacking (Murdock). Info gathering by investigative journalists include Public records laws. Federal Freedom of Information Act (FOIA) is good, but slow. California Public Records Act is a lot stronger. FOIA takes forever because of foot-dragging—it helps to be specific. Often need to sue (especially FBI). CPRA is faster, and requests can be vague. Dumps and leaks (a la Wikileaks) Journalists want: leads, protecting ourselves, our sources, and adapting tools for news gathering (Google hacking). Anonomity is important to whistleblowers. They want no digital footprint left behind (e.g., email, web log). They don't trust encryption, want to feel safe and secure. Whistleblower laws are very weak—there's no upside for whistleblowers—they have to be very passionate to do it. Accessibility and Security or: How I Learned to Stop Worrying and Love the Halting Problem Anna Shubina, Dartmouth College Anna talked about how accessibility and security are related. Accessibility of digital content (not real world accessibility). mostly refers to blind users and screenreaders, for our purpose. Accessibility is about parsing documents, as are many security issues. "Rich" executable content causes accessibility to fail, and often causes security to fail. For example MS Word has executable format—it's not a document exchange format—more dangerous than PDF or HTML. Accessibility is often the first and maybe only sanity check with parsing. They have no choice because someone may want to read what you write. Google, for example, is very particular about web browser you use and are bad at supporting other browsers. Uses JavaScript instead of links, often requiring mouseover to display content. PDF is a security nightmare. Executible format, embedded flash, JavaScript, etc. 15 million lines of code. Google Chrome doesn't handle PDF correctly, causing several security bugs. PDF has an accessibility checker and PDF tagging, to help with accessibility. But no PDF checker checks for incorrect tags, untagged content, or validates lists or tables. None check executable content at all. The "Halting Problem" is: can one decide whether a program will ever stop? The answer, in general, is no (Rice's theorem). The same holds true for accessibility checkers. Language-theoretic Security says complicated data formats are hard to parse and cannot be solved due to the Halting Problem. W3C Web Accessibility Guidelines: "Perceivable, Operable, Understandable, Robust" Not much help though, except for "Robust", but here's some gems: * all information should be parsable (paraphrasing) * if not parsable, cannot be converted to alternate formats * maximize compatibility in new document formats Executible webpages are bad for security and accessibility. They say it's for a better web experience. But is it necessary to stuff web pages with JavaScript for a better experience? A good example is The Drudge Report—it has hand-written HTML with no JavaScript, yet drives a lot of web traffic due to good content. A bad example is Google News—hidden scrollbars, guessing user input. Solutions: Accessibility and security problems come from same source Expose "better user experience" myth Keep your corner of Internet parsable Remember "Halting Problem"—recognize false solutions (checking and verifying tools) Stop Patching, for Stronger PCI Compliance Adam Brand, protiviti @adamrbrand, http://www.picfun.com/ Adam talked about PCI compliance for retail sales. Take an example: for PCI compliance, 50% of Brian's time (a IT guy), 960 hours/year was spent patching POSs in 850 restaurants. Often applying some patches make no sense (like fixing a browser vulnerability on a server). "Scanner worship" is overuse of vulnerability scanners—it gives a warm and fuzzy and it's simple (red or green results—fix reds). Scanners give a false sense of security. In reality, breeches from missing patches are uncommon—more common problems are: default passwords, cleartext authentication, misconfiguration (firewall ports open). Patching Myths: Myth 1: install within 30 days of patch release (but PCI §6.1 allows a "risk-based approach" instead). Myth 2: vendor decides what's critical (also PCI §6.1). But §6.2 requires user ranking of vulnerabilities instead. Myth 3: scan and rescan until it passes. But PCI §11.2.1b says this applies only to high-risk vulnerabilities. Adam says good recommendations come from NIST 800-40. Instead use sane patching and focus on what's really important. From NIST 800-40: Proactive: Use a proactive vulnerability management process: use change control, configuration management, monitor file integrity. Monitor: start with NVD and other vulnerability alerts, not scanner results. Evaluate: public-facing system? workstation? internal server? (risk rank) Decide:on action and timeline Test: pre-test patches (stability, functionality, rollback) for change control Install: notify, change control, tickets McAfee Secure & Trustmarks — a Hacker's Best Friend Jay James, Shane MacDougall, Tactical Intelligence Inc., Canada "McAfee Secure Trustmark" is a website seal marketed by McAfee. A website gets this badge if they pass their remote scanning. The problem is a removal of trustmarks act as flags that you're vulnerable. Easy to view status change by viewing McAfee list on website or on Google. "Secure TrustGuard" is similar to McAfee. Jay and Shane wrote Perl scripts to gather sites from McAfee and search engines. If their certification image changes to a 1x1 pixel image, then they are longer certified. Their scripts take deltas of scans to see what changed daily. The bottom line is change in TrustGuard status is a flag for hackers to attack your site. Entire idea of seals is silly—you're raising a flag saying if you're vulnerable.

    Read the article

  • WPF vs. WinForms - a Delphi programmer's perspective?

    - by Robert Oschler
    I have read most of the major threads on WPF vs. WinForms and I find myself stuck in the unfortunate ambivalence you can fall into when deciding between the tried and true previous tech (Winforms), and it's successor (WPF). I am a veteran Delphi programmer of many years that is finally making the jump to C#. My fellow Delphi programmers out there will understand that I am excited to know that Anders Hejlsberg, of Delphi fame, was the architect behind C#. I have a strong addiction to Delphi's VCL custom components, especially those involved in making multi-step Wizards and components that act as a container for child components. With that background, I am hoping that those of you that switched from Delphi to C# can help me with my WinForms vs. WPF decision for writing my initial applications. Note, I am very impatient when coding and things like full fledged auto-complete and proper debugger support can make or break a project for me, including being able to find readily available information on API features and calls and even more so, workarounds for bugs. The SO threads and comments in the early 2009 date range give me great concern over WPF when it comes to potential frustrations that could mar my C# UI development coding. On the other hand, spending an inordinate amount of time learning an API tech that is, even if it is not abandoned, soon to be replaced (WinForms), is equally troubling and I do find the GPU support in WPF tantalizing. Hence my ambivalence. Since I haven't learned either tech yet I have a rare opportunity to get a fresh start and not have to face the big "unlearning" curve I've seen people mention in various threads when a WinForms programmer makes the move to WPF. On the other hand, if using WPF will just be too frustrating or have other major negative consequences for an impatient RAD developer like myself, then I'll just stick with WinForms until WPF reaches the same level of support and ease of use. To give you a concrete example into my psychology as a programmer, I used VB and subsequently Delphi to completely avoid altogether the very real pain of coding with MFC, a Windows UI library that many developers suffered through while developing early Windows apps. I have never regretted my luck in avoiding MFC. It would also be comforting to know if Anders Hejlsberg had a hand in the architecture of WPF and/or WinForms, and if there are any disparities in the creative vision and ease of use embodied in either code base. Finally, for the Delphi programmers again, let me know how much "IDE schock" I'm in for when using WPF as opposed to WinForms, especially when it comes to debugger support. Any job market comments updated for 2011 would be appreciated too. -- roschler

    Read the article

  • WPF vs. WinForms - a Delphi programmer's perspective?

    - by Robert Oschler
    Hello all. I have read most of the major threads on WPF vs. WinForms and I find myself stuck in the unfortunate ambivalence you can fall into when deciding between the tried and true previous tech (Winforms), and it's successor (WPF). I am a veteran Delphi programmer of many years that is finally making the jump to C#. My fellow Delphi programmers out there will understand that I am excited to know that Anders Hejlsberg, of Delphi fame, was the architect behind C#. I have a strong addiction to Delphi's VCL custom components, especially those involved in making multi-step Wizards and components that act as a container for child components. With that background, I am hoping that those of you that switched from Delphi to C# can help me with my WinForms vs. WPF decision for writing my initial applications. Note, I am very impatient when coding and things like full fledged auto-complete and proper debugger support can make or break a project for me, including being able to find readily available information on API features and calls and even more so, workarounds for bugs. The SO threads and comments in the early 2009 date range give me great concern over WPF when it comes to potential frustrations that could mar my C# UI development coding. On the other hand, spending an inordinate amount of time learning an API tech that is, even if it is not abandoned, soon to be replaced (WinForms), is equally troubling and I do find the GPU support in WPF tantalizing. Hence my ambivalence. Since I haven't learned either tech yet I have a rare opportunity to get a fresh start and not have to face the big "unlearning" curve I've seen people mention in various threads when a WinForms programmer makes the move to WPF. On the other hand, if using WPF will just be too frustrating or have other major negative consequences for an impatient RAD developer like myself, then I'll just stick with WinForms until WPF reaches the same level of support and ease of use. To give you a concrete example into my psychology as a programmer, I used VB and subsequently Delphi to completely avoid altogether the very real pain of coding with MFC, a Windows UI library that many developers suffered through while developing early Windows apps. I have never regretted my luck in avoiding MFC. It would also be comforting to know if Anders Hejlsberg had a hand in the architecture of WPF and/or WinForms, and if there are any disparities in the creative vision and ease of use embodied in either code base. Finally, for the Delphi programmers again, let me know how much "IDE schock" I'm in for when using WPF as opposed to WinForms, especially when it comes to debugger support. Any job market comments updated for 2011 would be appreciated too. -- roschler

    Read the article

  • Evolution Of High Definition TV Viewing

    - by Gopinath
    The following guest post is written by Rob, who is also blogging on entertainment technology topics on iwantsky.com Gone are the days when you need to squint to be able to see the emotions on the faces of Humphrey Bogart and Ingrid Bergman as the lovers bid each other adieu in the classic film Casablanca. These days, watching an ordinary ant painstakingly carry a leaf in Animal Planet can be an exhilarating experience as you get to see not only the slightest movement but also the demarcation line between the insect’s head, thorax and abdomen. The crystal clear imagery was made possible by the sharp minds and the tinkering hands of the scientists that have designed the modern world’s HDTV. What is HDTV and what makes people so agog to have this new innovation in TV watching? HDTV stands for High Definition TV. Television viewing has indeed made a big leap. From the grainy black and whites, TV viewing had moved to colored TVs, progressed to SD TVs and now to HDTV. HDTV is the emerging trend in TV viewing as it delivers bigger and clearer pictures and better audio. Viewers can have a cinema-like TV viewing experience right in the comforts of their own home. With HDTV the viewer is allowed to have a better viewing range. With Standard (SD) TV, the viewer has to be at a distance that is from 3 to 6 times the size of the screen. HDTV allows the viewer to enjoy sharper and clearer images as it is possible to sit at a distance that is 1.5 or 3 times the size of the screen without noticing any image pixilation. Although HDTV appears to be a fairly new innovation, this system has actually existed in various forms years ago. Development of the HDTV was started in Europe as early as 1940s. However, the NTSC and the PAL/SECAM, the two analog TV standards became dominant and became popular worldwide. The analog TV was replaced by the digital TV platform in the 1990s. Even during the analog era, attempts have been made to develop HDTV. Japan has come out with MUSE system. However, due to channel bandwidth requirement concerns, the program was shelved. The entry of four organizations into the HDTV market spurred the development of a beneficial coalition. The AT&T, ATRC, MIT and Zenith HDTV combined forces. In 1993, a Grand Alliance was formed. This group is composed of researchers and HDTV manufacturers. A common standard for the broadcast system of HDTV was developed. In 1995, the system was tested and found successful. With the higher screen resolution of HDTV, viewing has never been more enjoyable. [Image courtesy: samsung] This article titled,Evolution Of High Definition TV Viewing, was originally published at Tech Dreams. Grab our rss feed or fan us on Facebook to get updates from us.

    Read the article

  • Informal Interviews: Just Relax (or Should I?)

    - by david.talamelli
    I was in our St Kilda Rd office last week and had the chance to meet up with Dan and David from GradConnection. I love what these guys are doing, their business has been around for two years and I really like how they have taken their own experiences from University found a niche in their market and have chased it. These guys are always networking. Whenever they come to Melbourne they send me a tweet to catch up, even though we often miss each other they are persistent. It sounds like their business is going from strength to strength and I have to think that success comes from their hard work and enthusiasm for their business. Anyway, before my meeting with ProGrad I noticed a tweet from Kevin Wheeler who was saying it was his last day in Melbourne - I sent him a message and we met up that afternoon for a coffee (I am getting to the point I promise). On my way back to the office after my meeting I was on a tram and was sitting beside a lady who was talking to her friend on her mobile. She had just come back from an interview and was telling her friend how laid back the meeting was and how she wasn't too sure of the next steps of the process as it was a really informal meeting. The recurring theme from this phone call was that 1) her and the interviewer got along really well and had a lot in common 2) the meeting was very informal and relaxed. I wasn't at the interview so I cannot say for certain, but in my experience regardless of the type of interview that is happening whether it is a relaxed interview at a coffee shop or a behavioural interview in an office setting one thing is consistent: the employer is assessing your ability to perform the role and fit into the company. Different interviewers I find have different interviewing styles. For example some interviewers may create a very relaxed environment in the thinking this will draw out less practiced answers and give a more realistic view of the person and their abilities while other interviewers may put the candidate "under the pump" to see how they react in a stressful situation. There are as many interviewing styles as there are interviewers. I think candidates regardless of the type of interview need to be professional and honest in both their skills/experiences, abilities and career plans (if you know what they are). Even though an interview may be informal, you shouldn't slip into complacency. You should not forget the end goal of the interview which is to get a job. Business happens outside of the office walls and while you may meet someone for a coffee it is still a business meeting no matter how relaxed the setting. You don't need to be stick in the mud and not let your personality shine through, but that first impression you make may play a big part in how far in the interview process you go. This article was originally posted on David Talamelli's Blog - David's Journal on Tap

    Read the article

  • SIM to OIM Migration: A How-to Guide to Avoid Costly Mistakes (SDG Corporation)

    - by Darin Pendergraft
    In the fall of 2012, Oracle launched a major upgrade to its IDM portfolio: the 11gR2 release.  11gR2 had four major focus areas: More simplified and customizable user experience Support for cloud, mobile, and social applications Extreme scalability Clear upgrade path For SUN migration customers, it is critical to develop and execute a clearly defined plan prior to beginning this process.  The plan should include initiation and discovery, assessment and analysis, future state architecture, review and collaboration, and gap analysis.  To help better understand your upgrade choices, SDG, an Oracle partner has developed a series of three whitepapers focused on SUN Identity Manager (SIM) to Oracle Identity Manager (OIM) migration. In the second of this series on SUN Identity Manager (SIM) to Oracle Identity Manager (OIM) migration, Santosh Kumar Singh from SDG  discusses the proper steps that should be taken during the planning-to-post implementation phases to ensure a smooth transition from SIM to OIM. Read the whitepaper for Part 2: Download Part 2 from SDGC.com In the last of this series of white papers, Santosh will talk about Identity and Access Management best practices and how these need to be considered when going through with an OIM migration. If you have not taken the opportunity, please read the first in this series which discusses the Migration Approach, Methodology, and Tools for you to consider when planning a migration from SIM to OIM. Read the white paper for part 1: Download Part 1 from SDGC.com About the Author: Santosh Kumar Singh Identity and Access Management (IAM) Practice Leader Santosh, in his capacity as SDG Identity and Access Management (IAM) Practice Leader, has direct senior management responsibility for the firm's strategy, planning, competency building, and engagement deliverance for this Practice. He brings over 12+ years of extensive IT, business, and project management and delivery experience, primarily within enterprise directory, single sign-on (SSO) application, and federated identity services, provisioning solutions, role and password management, and security audit and enterprise blueprint. Santosh possesses strong architecture and implementation expertise in all areas within these technologies and has repeatedly lead teams in successfully deploying complex technical solutions. About SDG: SDG Corporation empowers forward thinking companies to strategize their future, realize their vision, and minimize their IT risk. SDG distinguishes itself by offering flexible business models to fit their clients’ needs; faster time-to-market with its pre-built solutions and frameworks; a broad-based foundation of domain experts, and deep program management expertise. (www.sdgc.com)

    Read the article

  • SQLAuthority News – Book Review – Beginning T-SQL 2008 by Kathi Kellenberger

    - by pinaldave
    Beginning T-SQL 2008 by Kathi Kellenberger Amazon Link Detail Review: Beginning T-SQL 2008 is one of the best books on the market if you are just beginning to work with Microsoft SQL, or have a little bit of experience and need to learn more quickly. Each chapter of the book introduces a new subject, and builds upon topics covered in previous chapters.  The author of the book, Kathi Kellenberger understands that you need to form a solid foundation of knowledge before moving on to new topics, and sets up each subject nicely.  Because the chapters move in an orderly progression, you continue to use skills you learned earlier. One of the best features of Beginning T-SQL 2008 is that each chapter has multiple examples and exercises.  Many books introduce a topic and then never go back to it.  This book gives enough examples that you will be familiar with the subject when you come across it in real life.  The exercises at the end of the chapter mean that you will be using the skills you learned – and there is no better way to cement a subject in your brain. The book also includes discussions of the common errors that programmers will come across, how to avoid them, and how to fix them if they happen.  Ms. Kellenberger understands that not only do mistakes happen, but they are bound to happen if you aren’t trained properly.  Mistakes are part of the learning process! The book begins by discussions relational theory, so that programmers will understand the way T-SQL works from the ground up.  It also walks readers through writing accurate queries, combining set-based and procedural processing, embedding logic in stored functions, and so much more. Overall, the main goal of Beginning T-SQL 2008 is to introduce novices to SQL programming, and quickly familiarize them with the basics of running the program.  The book is written with the idea that readers will not know any of the technical terms or vocabulary.  However, if you are a little more familiar with SQL and looking to become better, you will still find this book very helpful. Ratting: 4.5+ Stars Summary: I must recommend Beginning T-SQL 2008 highly enough.  If you are going to buy any beginners guide to Transect-SQL, this is the one you should spend your money on.  You can save yourself a lot of time and effort later by using this very affordable manual to learn the basics, which will allow you to become an expert much faster. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQLAuthority Book Review, SQLAuthority News, T SQL, Technology

    Read the article

  • FAQ: GridView Calculation with JavaScript - Formatting and Validation

    - by Vincent Maverick Durano
    In my previous post here we've talked about how to calculate the sub-totals and grand total in GridView using JavaScript. In this post I'm going take more step further and will demonstrate how are we going to format the totals into a currency and how to validate the input that would only allow you to enter a whole number in the quantity TextBox. Here are the code blocks below: ASPX Source:   <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" > <head runat="server"> <title></title> <script type="text/javascript"> function CalculateTotals() { var gv = document.getElementById("<%= GridView1.ClientID %>"); var tb = gv.getElementsByTagName("input"); var lb = gv.getElementsByTagName("span"); var sub = 0; var total = 0; var indexQ = 1; var indexP = 0; var price = 0; for (var i = 0; i < tb.length; i++) { if (tb[i].type == "text") { ValidateNumber(tb[i]); price = lb[indexP].innerHTML.replace("$", "").replace(",", ""); sub = parseFloat(price) * parseFloat(tb[i].value); if (isNaN(sub)) { lb[i + indexQ].innerHTML = "0.00"; sub = 0; } else { lb[i + indexQ].innerHTML = FormatToMoney(sub, "$", ",", "."); ; } indexQ++; indexP = indexP + 2; total += parseFloat(sub); } } lb[lb.length - 1].innerHTML = FormatToMoney(total, "$", ",", "."); } function ValidateNumber(o) { if (o.value.length > 0) { o.value = o.value.replace(/[^\d]+/g, ''); //Allow only whole numbers } } function isThousands(position) { if (Math.floor(position / 3) * 3 == position) return true; return false; }; function FormatToMoney(theNumber, theCurrency, theThousands, theDecimal) { var theDecimalDigits = Math.round((theNumber * 100) - (Math.floor(theNumber) * 100)); theDecimalDigits = "" + (theDecimalDigits + "0").substring(0, 2); theNumber = "" + Math.floor(theNumber); var theOutput = theCurrency; for (x = 0; x < theNumber.length; x++) { theOutput += theNumber.substring(x, x + 1); if (isThousands(theNumber.length - x - 1) && (theNumber.length - x - 1 != 0)) { theOutput += theThousands; }; }; theOutput += theDecimal + theDecimalDigits; return theOutput; } </script> </head> <body> <form id="form1" runat="server"> <asp:gridview ID="GridView1" runat="server" ShowFooter="true" AutoGenerateColumns="false"> <Columns> <asp:BoundField DataField="RowNumber" HeaderText="Row Number" /> <asp:BoundField DataField="Description" HeaderText="Item Description" /> <asp:TemplateField HeaderText="Item Price"> <ItemTemplate> <asp:Label ID="LBLPrice" runat="server" Text='<%# Eval("Price","{0:C}") %>'></asp:Label> </ItemTemplate> </asp:TemplateField> <asp:TemplateField HeaderText="Quantity"> <ItemTemplate> <asp:TextBox ID="TXTQty" runat="server" onkeyup="CalculateTotals();"></asp:TextBox> </ItemTemplate> <FooterTemplate> <b>Total Amount:</b> </FooterTemplate> </asp:TemplateField> <asp:TemplateField HeaderText="Sub-Total"> <ItemTemplate> <asp:Label ID="LBLSubTotal" runat="server" ForeColor="Green" Text="0.00"></asp:Label> </ItemTemplate> <FooterTemplate> <asp:Label ID="LBLTotal" runat="server" ForeColor="Green" Font-Bold="true" Text="0.00"></asp:Label> </FooterTemplate> </asp:TemplateField> </Columns> </asp:gridview> </form> </body> </html> Code Behind Source:   public partial class GridCalculation : System.Web.UI.Page { private void BindDummyDataToGrid() { DataTable dt = new DataTable(); DataRow dr = null; dt.Columns.Add(new DataColumn("RowNumber", typeof(string))); dt.Columns.Add(new DataColumn("Description", typeof(string))); dt.Columns.Add(new DataColumn("Price", typeof(decimal))); dr = dt.NewRow(); dr["RowNumber"] = 1; dr["Description"] = "Nike"; dr["Price"] = "1000"; dt.Rows.Add(dr); dr = dt.NewRow(); dr["RowNumber"] = 2; dr["Description"] = "Converse"; dr["Price"] = "800"; dt.Rows.Add(dr); dr = dt.NewRow(); dr["RowNumber"] = 3; dr["Description"] = "Adidas"; dr["Price"] = "500"; dt.Rows.Add(dr); dr = dt.NewRow(); dr["RowNumber"] = 4; dr["Description"] = "Reebok"; dr["Price"] = "750"; dt.Rows.Add(dr); dr = dt.NewRow(); dr["RowNumber"] = 5; dr["Description"] = "Vans"; dr["Price"] = "1100"; dt.Rows.Add(dr); dr = dt.NewRow(); dr["RowNumber"] = 6; dr["Description"] = "Fila"; dr["Price"] = "200"; dt.Rows.Add(dr); //Bind the Gridview GridView1.DataSource = dt; GridView1.DataBind(); } protected void Page_Load(object sender, EventArgs e) { if (!IsPostBack) { BindDummyDataToGrid(); } } } Running the code above will display something like this: On initial load After entering the quantity in the TextBox That's it! I hope someone find this post useful! Technorati Tags: ASP.NET,C#,ADO.NET,JavaScript,GridView

    Read the article

  • A Few Words from Oracle’s Channel Chief

    - by Meghan Fritz-Oracle
    As Oracle enters a new fiscal year, I want to take a moment and reflect on my time at Oracle thus far. The technology industry is currently at an inflection point trying to figure out where growth will come from. When you look at Oracle’s portfolio of products, it's a complete stack from applications to disc, offering differentiation in the marketplace. I was initially drawn to Oracle’s leadership, strategy, and world-class technology. Since joining the Oracle team in October 2013, I’ve had the privilege of traveling around the globe visiting our partners and customers, and wanted to share several common themes that came up during these meetings. Cloud: Many partners are trying to figure out how to build a business around the cloud. Oracle partners can currently resell or refer our cloud services. We saw over 300 percent growth from cloud resale last quarter. Engineered Systems: Hardware and software integrated together to simplify IT allows our joint customers to focus on the innovation they need to compete in a complex marketplace. We're seeing great success in a several areas, with more partners saying, “Let’s start with Oracle on Oracle.” The Internet of Things: This is the next big opportunity for device manufacturers and ISV‘s to capture market share in what is projected to be a mulit-trillion-dollar opportunity, according to Gartner.  Competition: We've got a tremendous middleware platform and a tremendous database install base. We’re not just a database company; we are a complete provider. So looking ahead, what are my priorities for fiscal 2015? Oracle PartnerNetwork has some very exciting plans on the horizon. There’s a lot more leadership and announcements to unfold, especially at this year’s Global Partner Kickoff taking place on June 25 + 26 depending on your region and time zone. I along with several other Oracle executives will be shedding light on Oracle’s strategy for the upcoming year, the latest opportunities within the OPN Specialized Program and sales strategies that will help you to continue to grow and profit with Oracle. Stay tuned for registration information next week.We also have Oracle OpenWorld and JavaOne to look forward to. These conferences are taking place in San Francisco from September 28 – October 2. We’ll have a variety of partner-specific activities for you at OPN Central @ OpenWorld including the OPN keynote, the famed AfterDark networking reception, access to the OPN Lounge and more.In the meantime, I hope that everyone has a great end to fiscal 2014.Best regards,Rich Geraffo Senior Vice President, Worldwide Alliances and Channels

    Read the article

  • AxCMS.net 10 with Microsoft Silverlight 4 and Microsoft Visual Studio 2010

    - by Axinom
    Axinom, European WCM vendor, today announced the next version of its WCM solution AxCMS.net 10, which streamlines the processes involved in creating, managing and distributing corporate content on the internet. The new solution helps reducing ongoing costs for managing and distributing to large audiences, while at the same time drastically reducing time-to-market and one-time setup costs. http://www.AxCMS.net Axinom’s WCM portfolio, based on the Microsoft .NET Framework 4, Microsoft Visual Studio 2010 and Microsoft Silverlight 4, allows enterprises to increase process efficiency, reduce operating costs and more effectively manage delivery of rich media assets on the Web and mobile devices. Axinom solutions are widely used by major European online brands in IT, telco, retail, media and entertainment industries such as Siemens, American Express, Microsoft Corp., ZDF, Pro7Sat1 Media, and Deutsche Post. Brand New User Interface built with Silverlight 4By using Silverlight 4, Axinom’s team created a new user interface for AxCMS.net 10 that is optimized for improved usability and speed. WYSIWYG mode, integrated image editor, extended list views, and detail views of objects allow a substantial acceleration of typical editor tasks. Axinom’s team worked with Silverlight Rough Cut Editor for video management and Silverlight Analytics Framework for extended reporting to complete the wide range of capabilities included in the new release. “Axinom’s release of AxCMS.net 10 enables developers to take advantage of the latest features in Silverlight 4,” said Brian Goldfarb, director of the developer platform group at Microsoft Corp. “Microsoft is excited about the opportunity this creates for Web developers to streamline the creating, managing and distributing of online corporate content using AxCMS.net 10 and Silverlight.” Rapid Web Development with Visual Studio 2010AxCMS.net 10 is extended by additional products that enable developers to get productive quickly and help solve typical customer scenarios. AxCMS.net template projects come with documented source code that help kick-start projects and learn best practices in all aspects of Web application development. AxCMS.net overcomes many hard-to-solve technical obstacles in an out-of-the-box manner by providing a set of ready-to-use vertical solutions such as corporate Web site, Web shop, Web campaign management, email marketing, multi-channel distribution, management of rich Internet applications, and Web business intelligence. Extended Multi-Site ManagementAxCMS.net has been supporting the management of an unlimited number of Web sites for a long time. The new version 10 of AxCMS.net will further improve multi-site management and provide features to editors and developers that will simplify and accelerate multi-site and multi-language management. Extended publication workflow will take into account additional dependencies of dynamic objects, pages, and documents. “The customer requests evolved from static html pages to dynamic Web applications content with the emergence of rich media assets seamlessly combined across many channels including Web, mobile and IPTV. With the.NET Framework 4 and Silverlight 4, we’re on the fast track to making the three screen strategy a reality for our customers,” said Damir Tomicic, CEO of Axinom Group. “Our customers enjoy substantial competitive advantages of using latest Microsoft technologies. We have a long-standing, relationship with Microsoft and are committed to continued development using Microsoft tools and technologies to deliver innovative Web solutions in the future.”  

    Read the article

  • Silverlight Cream for March 10, 2010 -- #810

    - by Dave Campbell
    In this Issue: Andrea Boschin, Jeremy Likness(-2-), Andrew Veresov, Nokola, SilverLaw, Gill Cleeren, Jim Wightman and Jeremy Likness, Viktor Larsson(-2-), and Walter Ferrari. Shoutouts: Viktor Larsson has a post up about Silverlight Market Penetration ... hope to meet you at MIX10, Viktor! Gergely Orosz has posted the Slides and code for the presentation “An Introduction to Silverlight” It appears that if I miss a day, I can pretty much do an all-submittal post :) From SilverlightCream.com: Writing an AsyncLoader to enqueue long running operations Andrea Boschin has a tutorial on SilverlightShow where he's building up an asynch service to deal with a long-running app on the server. MVVM with MEF in Silverlight: Video Tutorial Jeremy Likness has a video tutorial up for helping beginners wire up MVVM and MEF to Silverlight. Source code for the app in the video is downloadable. MVVM with MEF in Silverlight Video Tutorial Part 2: Plugins and Metadata In part 2, Jeremy Likness redesigns the app using metadata to turn the shapes into objects, and then show how easy it is to add a new plugin... and the source for the app is downloadable. Binding a Converter Parameter Andrew Veresov has a nice code-filled solution up for those times that you need to bind a ConverterParameter value. EasyPainter: Lion Hair styling Nokola has not been idle with Easy Painter... now he's added "Lion Hair" to the list of stylings you can apply... guess if you want to change someone's 'mane' ... sorry! Twisting Navigation - Silverlight 3 SilverLaw has another control up - a "Twisting Navigation" control... very cool :) ... and since I'm behind the curve, he already has an update in the Expression Gallery as noted in his post, and a video tutorial on implementing it in an application... and if you understand German, turn up the sound :) Uploading and downloading images using a WCF service with Silverlight Gill Cleeren has a tutorial up at SilverlightShow on uploading and downloading images using WCF Services in Silverlight New Windows Phone 7 Community Developer Hub Jim Wightman and Jeremy Likness have a very cool Silverlight page up where you can paste the URL of your XAP in and have it display in a "Windows 7 Series Phone" ... and that's all I'm saying about that. XAML Transformation 101 Viktor Larsson is discussing Transforms in XAML and has a nice tutorial up that is easily the beginning of a carousel... you may also want to check out his other posts... I'm adding him to my list. Silverlight 4 Webcam Demo In this post, Viktor Larsson has a tutorial up for using the WebCam. This is from a beginner perspective, so if you haven't jumped in, now's a good time. How to extend Bing Maps Silverlight with an elevation profile graph - Part 1 Walter Ferrari has a post up at SilverlightShow discussing extensions to BingMaps such as creating routes using GeoCoding and Route Services plus drawing lines on the maps and getting coordinates of the points. Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    MIX10

    Read the article

  • Oracle anuncia resultados de Q3 FY10

    - by Paulo Folgado
    Oracle Reports GAAP EPS of $0.23, Non-GAAP EPS of $0.38New Software Licenses Up 13%, Applications New Licenses Up 21%Oracle Corporation today announced fiscal 2010 Q3 GAAP total revenues were up 17% to $6.4 billion, while non-GAAP total revenues were up 18% to $6.5 billion. Excluding the impact of Sun Microsystems, Inc., which Oracle acquired on January 26, 2010, GAAP total revenue grew 7%. GAAP new software license revenues were up 13% to $1.7 billion, and up 10% to $1.7 billion excluding Sun. GAAP software license updates and product support revenues were up 13% to $3.3 billion, while non-GAAP software license updates and product support revenues were up 12% to $3.3 billion. GAAP operating income was down 5% to $1.8 billion, and GAAP operating margin was 29%. Non-GAAP operating income was up 13% to $2.9 billion, and non-GAAP operating margin was 45%. GAAP net income was down 10% to $1.2 billion, while non-GAAP net income was up 9% to $1.9 billion. GAAP earnings per share were $0.23, down 11% compared to last year while non-GAAP earnings per share were up 9% to $0.38. GAAP operating cash flow on a trailing twelve-month basis was $8.2 billion. "Our solid top line growth, coupled with disciplined expense management, was key in generating $8.0 billion of free cash flow over the last twelve months," said Oracle CFO Jeff Epstein."The Sun integration is going even better than we expected," said Oracle President, Safra Catz. "We believe that Sun will make a significant contribution to our fourth quarter earnings per share as well as meet the profitability goals we set for next year.""Exadata is the fastest growing product in Oracle's history," said Oracle President, Charles Phillips. "Introduced a little over a year ago, the Exadata pipeline is now approaching $400 million with Q4 bookings forecast at nearly $100 million. This strengthens both sales growth and profitability in our Sun server and storage businesses.""Every quarter we grab huge chunks of market share from SAP," said Oracle CEO, Larry Ellison. "SAP's most recent quarter was the best quarter of their year, only down 15%, while Oracle's application sales were up 21%. But SAP is well ahead of us in the number of CEOs for this year, announcing their third and fourth, while we only had one."In addition, Oracle's Board of Directors declared a cash dividend of $0.05 per share of outstanding common stock to be paid to stockholders of record as of the close of business on April 14, 2010, with a payment date of May 5, 2010. Future declarations of quarterly dividends and the establishment of future record and payment dates are subject to the final determination of Oracle's Board of Directors.Q3 Earnings Conference Call and WebcastOracle will hold a conference call and web broadcast today to discuss these results at 2:00 p.m. Pacific. You may listen to the call by dialing (800) 214-0694 or (719) 955-1425, Passcode: 567035. To access the live Web broadcast of this event, please visit the Oracle Investor Relations Web site at http://www.oracle.com/investor.

    Read the article

  • New Netra SPARC T3 Servers

    - by Ferhat Hatay
    Today at the Mobile World Congress 2011, Oracle announced two new carrier-grade NEBS Level 3- certified servers: Oracle’s Netra SPARC T3-1 rackmount server and Oracle’s Netra SPARC T3-1BA ATCA blade server bringing the performance, scalability and power efficiency of the newest SPARC T3 processor to the communications market.    The Netra SPARC T3-1 server enclosure has a compact 20inch-deep carrier-grade rack-optimized design The new Netra SPARC T3 servers further expand Oracle’s complete portfolio for the communications industry, which includes carrier-grade servers, storage and application software to run operations support systems and service delivery platforms with easy migration capabilities and unmatched investment protection via the binary compatibility guarantee of the Oracle Solaris operating system. With advanced reliability, networking and security features built-in to Oracle Solaris – the most widely deployed carrier-grade OS – the systems announced today are uniquely suited for mission-critical core network infrastructure and service delivery. The world’s first carrier-grade system using the 16-core, 128-thread SPARC T3 processor, the Netra SPARC T3-1 server supports 2x the I/O bandwidth, 2x the memory and is 35 percent faster than the previous generation. With integrated on-chip 10 Gigabit Ethernet, on-chip cryptographic acceleration, and built-in, no-cost Oracle VM Server for SPARC and Oracle Solaris Containers for virtualization, the Netra SPARC T3-1 server is an ideal platform for consolidation, offering 128 virtual systems in a single server. As the next generation Netra SPARC ATCA blade, Netra SPARC T3-1BA ATCA blade server brings the PICMG 3.0 compatibility, NEBS Level 3 Certification, ETSI compliance and the Netra business practices to the customer solution. The Netra SPARC T3-1BA ATCA blade server can be mixed in the Sun Netra CT900 blade chassis with other ATCA UltraSPARC and x86 blades.     The Netra SPARC T3-1BA ATCA blade server   The Netra SPARC T3-1BA ATCA blade server delivers industry-leading scalability, density and cost efficiency with up to 36 SPARC T3 processors (3456 processing threads) in a single rack – a 50 percent increase over the previous generation. The Netra SPARC T3-1BA blade server also offers high-bandwidth and high-capacity I/O, with greater memory capacity to tackle the increasing business demands of the communications industry. For service providers faced with the rapid growth of broadband networks and the dramatic surge in global smartphone adoption, the new Netra SPARC T3 systems deliver continuous availability with massive scalability, tested and certified to run in the harshest conditions. More information Oracle’s Sun Netra Servers Scaling Throughput and Managing TCO with Oracle’s Netra SPARC T3-1 Servers Enabling End-to-End 10 Gigabit Ethernet in Oracle's Sun Netra ATCA Product Family Data Sheet: Netra SPARC T3-1BA ATCA Blade Server Data Sheet: Netra SPARC T3-1 Server Oracle Solaris: The Carrier Grade Operating System

    Read the article

  • Raymond James at Oracle OpenWorld: Showcasing Real Time Data Integration.

    - by Christophe Dupupet
    Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} In today’s always-on, always connected world, integrating data in real-time is a necessity for most companies and most industries. The experts at Raymond James Financials, using Oracle GoldenGate and Oracle Data Integrator, have designed a real-time data integration solution for their operational data store and services that support applications throughout the enterprise . They boast an amazing number of daily executions, while dramatically reducing data latency,  increasing data service performance, and speeding time to market. Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";} To know more on how they have achieved such results, come listen to Ryan Fonnett and Tim Garrod: they will explain how they implemented their solution, and also illustrate their explanations with a live demonstration of their work. A presentation not to be missed! Real-Time Data Integrationwith Oracle Data Integratorat Raymond James October 1st 2012 at 4:45pm Moscone West, room 3005

    Read the article

< Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >