Search Results

Search found 20099 results on 804 pages for 'virtual host'.

Page 194/804 | < Previous Page | 190 191 192 193 194 195 196 197 198 199 200 201  | Next Page >

• Intel I217LM ethernet controller not detected by Ubuntu 12.04LTS

  - by Alexandr Kurilin

  My last installation of Ubuntu 12.04 on a machine using an ASUS Q87M-E motherboard with an Intel I217LM Ethernet controller has failed to detect the ethernet card. The only thing displayed by ifconfig -a is the loopback. I double-checked in the BIOS, and the controller should be online. $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no $ lspci 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:02.0 VGA compatible controller: Intel Corporation Haswell Integrated Graphics Controller (rev 06) 00:03.0 Audio device: Intel Corporation Haswell HD Audio Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:16.3 Serial controller: Intel Corporation Lynx Point KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation Device 153a (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point HD Audio Controller (rev 04) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-Port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) $ lsmod Module Size Used by vesafb 13844 1 snd_hda_codec_realtek 224173 1 arc4 12529 2 joydev 17693 0 usbhid 47238 0 hid 99636 1 usbhid rfcomm 47604 0 rt73usb 31735 0 crc_itu_t 12707 1 rt73usb rt2x00usb 20808 1 rt73usb rt2x00lib 55326 2 rt73usb,rt2x00usb mac80211 506862 2 rt2x00usb,rt2x00lib cfg80211 205774 2 rt2x00lib,mac80211 eeepc_wmi 13109 0 bnep 18281 2 asus_wmi 24456 1 eeepc_wmi sparse_keymap 13890 1 asus_wmi psmouse 97485 0 bluetooth 180153 10 rfcomm,bnep ppdev 17113 0 snd_hda_intel 33719 6 snd_hda_codec 127706 2 snd_hda_codec_realtek,snd_hda_intel snd_seq_midi 13324 0 snd_hwdep 17764 1 snd_hda_codec snd_rawmidi 30748 1 snd_seq_midi serio_raw 13211 0 snd_pcm 97275 2 snd_hda_intel,snd_hda_codec snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq parport_pc 32866 1 snd 79041 21 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_rawmidi,snd_pcm,snd_seq,snd_timer,snd_seq_device video 19651 0 soundcore 15091 1 snd wmi 19256 1 asus_wmi snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp $ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1091 errors:0 dropped:0 overruns:0 frame:0 TX packets:1091 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:80048 (80.0 KB) TX bytes:80048 (80.0 KB) wlan0 Link encap:Ethernet HWaddr 00:fd:07:91:a8:b9 inet addr:172.16.42.4 Bcast:172.16.42.255 Mask:255.255.255.0 inet6 addr: fe80::2fd:7ff:fe91:a8b9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:56644 errors:0 dropped:0 overruns:0 frame:0 TX packets:36417 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:85270918 (85.2 MB) TX bytes:3413849 (3.4 MB) additionally, running sudo lshw -C network returns: *-network UNCLAIMED description: Ethernet Controller [...] I'm pretty stumped at this point. This doesn't sound like a very uncommon ethernet controller and I figured it would be picked up by the system. Does anybody have advice for how to deal with this? Anything specific I should look into to figure out what could be causing this? Edit: It seems that following the guide on the Intel e1000e drivers page allowed the card to start working. Is this a real fix or is there a better way?

  Read the article

• The new Auto Scaling Service in Windows Azure

  - by shiju

  One of the key features of the Cloud is the on-demand scalability, which lets the cloud application developers to scale up or scale down the number of compute resources hosted on the Cloud. Auto Scaling provides the capability to dynamically scale up and scale down your compute resources based on user-defined policies, Key Performance Indicators (KPI), health status checks, and schedules, without any manual intervention. Auto Scaling is an important feature to consider when designing and architecting cloud based solutions, which can unleash the real power of Cloud to the apps for providing truly on-demand scalability and can also guard the organizational budget for cloud based application deployment. In the past, you have had to leverage the the Microsoft Enterprise Library Autoscaling Application Block (WASABi) or a services like  MetricsHub for implementing Automatic Scaling for your cloud apps hosted on the Windows Azure. The WASABi required to host your auto scaling block in a Windows Azure Worker Role for effectively implementing the auto scaling behaviour to your Windows Azure apps. The newly announced Auto Scaling service in Windows Azure lets you add automatic scaling capability to your Windows Azure Compute Services such as Cloud Services, Web Sites and Virtual Machine. Unlike WASABi hosted on a Worker Role, you don’t need to host any monitoring service for using the new Auto Scaling service and the Auto Scaling service will be available to individual Windows Azure Compute Services as part of the Scaling. Configure Auto Scaling for a Windows Azure Cloud Service Currently the Auto Scaling service supports Cloud Services, Web Sites and Virtual Machine. In this demo, I will be used a Cloud Services app with a Web Role and a Worker Role. To enable the Auto Scaling, select t your Windows Azure app in the Windows Azure management portal, and choose “SCLALE” tab. The Scale tab will show the all information regards with Auto Scaling. The below image shows that we have currently disabled the AutoScale service. To enable Auto Scaling, you need to choose either CPU or QUEUE. The QUEUE option is not available for Web Sites. The image below demonstrates how to configure Auto Scaling for a Web Role based on the utilization of CPU. We have configured the web role app for running with 1 to 5 Virtual Machine instances based on the CPU utilization with a range of 50 to 80%. If the aggregate utilization is becoming above above 80%, it will scale up instances and it will scale down instances when utilization is becoming below 50%. The image below demonstrates how to configure Auto Scaling for a Worker Role app based on the messages added into the Windows Azure storage Queue. We configured the worker role app for running with 1 to 3 Virtual Machine instances based on the Queue messages added into the Windows Azure storage Queue. Here we have specified the number of messages target per machine is 2000. The image below shows the summary of the Auto Scaling for the Cloud Service after configuring auto scaling service. Summary Auto Scaling is an extremely important behaviour of the Cloud applications for providing on-demand scalability without any manual intervention. Windows Azure provides greater support for enabling Auto Scaling for the apps deployed on the Windows Azure cloud platform. The new Auto Scaling service in Windows Azure lets you add automatic scaling capability to your Windows Azure Compute Services such as Cloud Services, Web Sites and Virtual Machine. In the new Auto Scaling service, you don’t have to host any monitor service like you have had in WASABi block. The Auto Scaling service is an excellent alternative to the manually hosting WASABi block in a Worker Role app.

  Read the article

• Microsoft hosting free Hyper-V training for VMware Pros

  - by Ryan Roussel

  Microsoft will be hosting free training for virtualization professionals focused on Hyper-V, System Center, and virtualization architecture.  Details are below:   Just one week after Microsoft Management Summit 2011 (MMS), Microsoft Learning will be hosting an exclusive three-day Jump Start class specially tailored for VMware and Microsoft virtualization technology pros.  Registration for “Microsoft Virtualization for VMware Professionals” is open now and will be delivered as an online class on March 29-31, 2010 from 10:00am-4:00pm PDT.    The course is COMPLETELY FREE and OPEN TO ANYONE!  Please share with your customers, blog, Tweet, etc. – help us get the word out to strengthen support for Microsoft’s virtualization offerings. What’s the high-level overview? This cutting edge course will feature expert instruction and real-world demonstrations of Hyper-V and brand new releases from System Center Virtual Machine Manager 2012 Beta (many of which will be announced just one week earlier at MMS).  Register Now!   Day 1 will focus on “Platform” (Hyper-V, virtualization architecture, high availability & clustering) 10:00am – 10:30pm PDT:  Virtualization 360 Overview 10:30am – 12:00pm:  Microsoft Hyper-V Deployment Options & Architecture 1:00pm – 2:00pm:  Differentiating Microsoft and VMware (terminology, etc.) 2:00pm – 4:00pm:  High Availability & Clustering Day 2 will focus on “Management” (System Center Suite, SCVMM 2012 Beta, Opalis, Private Cloud solutions) 10:00am – 11:00pm PDT:  System Center Suite Overview w/ focus on DPM 11:00am – 12:00pm:  Virtual Machine Manager 2012 | Part 1 1:00pm –   1:30pm:  Virtual Machine Manager 2012 | Part 2 1:30pm – 2:30pm:  Automation with System Center Opalis & PowerShell 2:30pm – 4:00pm:  Private Cloud Solutions, Architecture & VMM SSP 2.0 Day 3 will focus on “VDI” (VDI Infrastructure/architecture, v-Alliance, application delivery via VDI) 10:00am – 11:00pm PDT:  Virtual Desktop Infrastructure (VDI) Architecture | Part 1 11:00am – 12:00pm:  Virtual Desktop Infrastructure (VDI) Architecture | Part 2 1:00pm – 2:30pm:  v-Alliance Solution Overview 2:30pm – 4:00pm:  Application Delivery for VDI     Every section will be team-taught by two of the most respected authorities on virtualization technologies: Microsoft Technical Evangelist Symon Perriman and leading Hyper-V, VMware, and XEN infrastructure consultant, Corey Hynes Who is the target audience for this training? Suggested prerequisite skills include real-world experience with Windows Server 2008 R2, virtualization and datacenter management. The course is tailored to these types of roles: · IT Professional · IT Decision Maker · Network Administrators & Architects · Storage/Infrastructure Administrators & Architects How do I to register and learn more about this great training opportunity? · Register: Visit the Registration Page and sign up for all three sessions · Blog: Learn more from the Microsoft Learning Blog · Twitter: Here are a few posts you can retweet: o Mar. 29-31 "Microsoft #Virtualization for VMware Pros" @SymonPerriman Corey Hynes http://bit.ly/JS-Hyper-V @MSLearning #Hyper-V o @SysCtrOpalis Mar. 29-31 "Microsoft #Virtualization for VMware Pros" @SymonPerriman Corey Hynes http://bit.ly/JS-Hyper-V #Hyper-V o Learn all the cool new features in Hyper-V & System Center 2012! SCVMM, Self-Service Portal 2.0, http://bit.ly/JS-Hyper-V #Hyper-V #Opalis What is a “Jump Start” course? A “Jump Start” course is “team-taught” by two expert instructors in an engaging radio talk show style format. The idea is to deliver readiness training on strategic and emerging technologies that drive awareness at scale before Microsoft Learning develops mainstream Microsoft Official Courses (MOC) that map to certifications.  All sessions are professionally recorded and distributed through MS Showcase, Channel 9, Zune Marketplace and iTunes for broader reach.

  Read the article

• General website publishing questions involving domain forwarding issue

  - by Gorgeousyousuf

  Even though I have been having a certain level of knowledge and experience about web development I have never interested in obtaining a domain and publishing a website from my own server. Since today I have been struggling with getting my own domain and configuring it utilizing web sources. I started with learning the outline of web publishing process including web server installation, deploying a website for testing purpose,router port forwarding, getting a domain and forwarding domain to my router which will also forward http requests to my web server I am confused about some parts and so far could not get the web site accessed from outside of the network. All I try to do is just for learning purpose so I do not pay much attention to security issues for now. I have Server 2008 and IIS 7.5 installed. I use a laptop and have access to the modem over wireless and my modem is Zoom x6 5590. Well I will continue explaining what I have done so far and what I think will be after each action I did, I have successfully had access to my website on any local computer entering the internal ip address and port pair of the host machine in a browser. Next, I forwarded port 80 of my host machine creating a virtual server like 10.0.0.x(internal ip(static) of the host) - tcp - start port : 80 - end port : 80 in router options. Now I suppose every request that will come to the public Ip on port 80 will be forwarded to my host machine(10.0.0.x) over port 80. So If everyhing went as desired, the website listening on port 80 will accept the request and process the issue and finally respond bla bla bla... I suppose to access my website from outside of the network by entering http://MyPublicIp:80 in a browser but I couldn't accomplish this task by now despite using godady's domain forwarding tool,I see a small view of my website when I click the "preview" button that checks whether the address(http://publicip/Index.aspx) I entered where my domain will be forwarded is available or not. I am sure that configuring domain does not play a role in solving such a problem since using public ip and port matching does not help. So here is the first question, What is the fact that I face this problem? After that, I have couple of question regarding domain forwarding using godaddy tool. Can I forward my domain to a any port for example port 8080 other than default http port 80? Additionally, can I use a sub-domain to forward to a different port of the host? What I want to design is if the client enters www.mydomain.com, website1 will respond over a specified port and after when a client enters info.mydomain.com, another website which listens on different port will respond. I tried to add a sub-domain and forward it to a address like http://www.mydomain.com:8080/Index.aspx with no success. Can I really do that? Finally, what if I have a ftp site listening on the default port 21 and I create a domain like ftp.mydomain.com that will forward to that ftp site address. Is it possible to use sub-domains for ftp site access? I know I am more than confused but no matter whatever and however you reply to me, you will help me have a more clear view on this subject. Thank you very much from now.

  Read the article

• cannot access a site from Mac OSX Lion but can from other machines on network?

  - by house9

  SOLVED: The issue is with the hamachi client, hamachi is hi-jacking all of the 5.0.0.0/8 address block http://en.wikipedia.org/wiki/Hamachi_(software)#Criticism http://b.logme.in/2012/11/07/changes-to-hamachi-on-november-19th/ The fix on Mac LogMeIn Hamachi Preferences Settings Advanced Peer Connections IP protocol mode IPv6 only (default is both) If you can only connect to some of your network over IPv4 this 'fix' will NOT work for you ----- A few weeks ago I started using a service - https://semaphoreapp.com I think they made DNS changes a week ago and ever since I cannot access the site from my Mac OSX Lion (10.7.4) machine (my main development machine) but I can access the site from other machines on my network ipad windows machine MacMini (10.6.8) After some google searching I tried both of these dscacheutil -flushcache sudo killall -HUP mDNSResponder but no go, I've contacted semaphoreapp as well, but nothing so far - also of interest, one of my colleagues has the exact same problem, cannot access via Mac OSX Lion but can via windows machine, we work remotely and are not on the same ISP some additional info Lion (10.7.4) cannot access site host semaphoreapp.com semaphoreapp.com has address 5.9.53.16 ping semaphoreapp.com PING semaphoreapp.com (5.9.53.16): 56 data bytes Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 Request timeout for icmp_seq 3 ping: sendto: No route to host Request timeout for icmp_seq 4 ping: sendto: Host is down Request timeout for icmp_seq 5 ping: sendto: Host is down Request timeout for icmp_seq 6 ping: sendto: Host is down Request timeout for icmp_seq 7 .... traceroute semaphoreapp.com traceroute to semaphoreapp.com (5.9.53.16), 64 hops max, 52 byte packets 1 * * * 2 * * * traceroute: sendto: No route to host 3 traceroute: wrote semaphoreapp.com 52 chars, ret=-1 *traceroute: sendto: Host is down traceroute: wrote semaphoreapp.com 52 chars, ret=-1 .... and MacMini (10.6.8) can access it host semaphoreapp.com semaphoreapp.com has address 5.9.53.16 ping semaphoreapp.com PING semaphoreapp.com (5.9.53.16): 56 data bytes 64 bytes from 5.9.53.16: icmp_seq=0 ttl=44 time=191.458 ms 64 bytes from 5.9.53.16: icmp_seq=1 ttl=44 time=202.923 ms 64 bytes from 5.9.53.16: icmp_seq=2 ttl=44 time=180.746 ms 64 bytes from 5.9.53.16: icmp_seq=3 ttl=44 time=200.616 ms 64 bytes from 5.9.53.16: icmp_seq=4 ttl=44 time=178.818 ms .... traceroute semaphoreapp.com traceroute to semaphoreapp.com (5.9.53.16), 64 hops max, 52 byte packets 1 192.168.0.1 (192.168.0.1) 1.677 ms 1.446 ms 1.445 ms 2 * LOCAL ISP 11.957 ms * 3 etc... 10.704 ms 14.183 ms 9.341 ms 4 etc... 32.641 ms 12.147 ms 10.850 ms 5 etc.... 44.205 ms 54.563 ms 36.243 ms 6 vlan139.car1.seattle1.level3.net (4.53.145.165) 50.136 ms 45.873 ms 30.396 ms 7 ae-32-52.ebr2.seattle1.level3.net (4.69.147.182) 31.926 ms 40.507 ms 49.993 ms 8 ae-2-2.ebr2.denver1.level3.net (4.69.132.54) 78.129 ms 59.674 ms 49.905 ms 9 ae-3-3.ebr1.chicago2.level3.net (4.69.132.62) 99.019 ms 82.008 ms 76.074 ms 10 ae-1-100.ebr2.chicago2.level3.net (4.69.132.114) 96.185 ms 75.658 ms 75.662 ms 11 ae-6-6.ebr2.washington12.level3.net (4.69.148.145) 104.322 ms 105.563 ms 118.480 ms 12 ae-5-5.ebr2.washington1.level3.net (4.69.143.221) 93.646 ms 99.423 ms 96.067 ms 13 ae-41-41.ebr2.paris1.level3.net (4.69.137.49) 177.744 ms ae-44-44.ebr2.paris1.level3.net (4.69.137.61) 199.363 ms 198.405 ms 14 ae-47-47.ebr1.frankfurt1.level3.net (4.69.143.141) 176.876 ms ae-45-45.ebr1.frankfurt1.level3.net (4.69.143.133) 170.994 ms ae-46-46.ebr1.frankfurt1.level3.net (4.69.143.137) 177.308 ms 15 ae-61-61.csw1.frankfurt1.level3.net (4.69.140.2) 176.769 ms ae-91-91.csw4.frankfurt1.level3.net (4.69.140.14) 178.676 ms 173.644 ms 16 ae-2-70.edge7.frankfurt1.level3.net (4.69.154.75) 180.407 ms ae-3-80.edge7.frankfurt1.level3.net (4.69.154.139) 174.861 ms 176.578 ms 17 as33891-net.edge7.frankfurt1.level3.net (195.16.162.94) 175.448 ms 185.658 ms 177.081 ms 18 hos-bb1.juniper4.rz16.hetzner.de (213.239.240.202) 188.700 ms 190.332 ms 188.196 ms 19 hos-tr4.ex3k14.rz16.hetzner.de (213.239.233.98) 199.632 ms hos-tr3.ex3k14.rz16.hetzner.de (213.239.233.66) 185.938 ms hos-tr2.ex3k14.rz16.hetzner.de (213.239.230.34) 182.378 ms 20 * * * 21 * * * 22 * * * any ideas? EDIT: adding tcpdump MacMini (which can connect) while running - ping semaphoreapp.com sudo tcpdump -v -i en0 dst semaphoreapp.com Password: tcpdump: listening on en0, link-type EN10MB (Ethernet), capture size 65535 bytes 17:33:03.337165 IP (tos 0x0, ttl 64, id 20153, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->3129)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 0, length 64 17:33:04.337279 IP (tos 0x0, ttl 64, id 26049, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->1a21)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 1, length 64 17:33:05.337425 IP (tos 0x0, ttl 64, id 47854, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->c4f3)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 2, length 64 17:33:06.337548 IP (tos 0x0, ttl 64, id 24772, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->1f1e)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 3, length 64 17:33:07.337670 IP (tos 0x0, ttl 64, id 8171, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->5ff7)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 4, length 64 17:33:08.337816 IP (tos 0x0, ttl 64, id 35810, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->f3ff)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 5, length 64 17:33:09.337948 IP (tos 0x0, ttl 64, id 31120, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->652)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 6, length 64 ^C 7 packets captured 1047 packets received by filter 0 packets dropped by kernel OSX Lion (cannot connect) while running - ping semaphoreapp.com # wireless ~ $ sudo tcpdump -v -i en1 dst semaphoreapp.com Password: tcpdump: listening on en1, link-type EN10MB (Ethernet), capture size 65535 bytes ^C 0 packets captured 262 packets received by filter 0 packets dropped by kernel and # wired ~ $ sudo tcpdump -v -i en0 dst semaphoreapp.com tcpdump: listening on en0, link-type EN10MB (Ethernet), capture size 65535 bytes ^C 0 packets captured 219 packets received by filter 0 packets dropped by kernel above output after Request timeout for icmp_seq 25 or 30 times from ping. I don't know much about tcpdump, but to me it doesn't seem like the ping requests are leaving my machine?

  Read the article

• 64-bit Windows CE 5.0 Emulator

  - by FreshCode

  When attempting to run the Windows CE 5.0 emulator on my 64-bit system, I get the following error: "Emulator for Windows CE is incompatible with the host operating system. Emulator for CE will not run on 64-bit host operating systems.64-bit host operating systems." How can I run the Windows CE 5.0 Emulator under 64-bit Windows 7 without resorting to a VM?

  Read the article

• How to get a safecontrol entry into manifest.xml with WSPBuilder project

  - by andrew

  Upon taking the default sharepoint master page for MySite, making some changes, and making a wsp out of it with WSPBuilder, I come to these errors in my logs: http://spoint/MySite/%5Fcatalogs/masterpage/MySite.master - An unexpected error has been encountered in this Web Part. Error: The control with virtual path '_controltemplates/Welcome.ascx' is not in the safe controls list for web at URL 'http://spoint/MySite'., Source: [UnsafeControlException: The control with virtual path '_controltemplates/Welcome.ascx' is not in the safe controls list for web at URL 'http://spoint/MySite' (stack trace omitted) http://spoint/MySite/%5Fcatalogs/masterpage/MySite.master - An unexpected error has been encountered in this Web Part. Error: The control with virtual path '_controltemplates/DesignModeConsole.ascx' is not in the safe controls list for web at URL 'http://spoint/MySite'., Source: [UnsafeControlException: The control with virtual path '_controltemplates/DesignModeConsole.ascx' is not in the safe controls list for web at URL 'http://spoint/MySite' (stack trace ommited) So, this masterpage does in fact use these OOTB controls and so I guess I need to get them safecontrolled. And I guess I want to do this via the manifest.xml. But I do not see how to make WSPBuilder do this.

  Read the article

• How to resovle javax.mail.AuthenticationFailedException issue?

  - by jl

  Hi, I am doing a sendMail Servlet with JavaMail. I have javax.mail.AuthenticationFailedException on my output. Can anyone please help me out? Thanks. sendMailServlet code: try { String host = "smtp.gmail.com"; String from = "[email protected]"; String pass = "pass"; Properties props = System.getProperties(); props.put("mail.smtp.starttls.enable", "true"); props.put("mail.smtp.host", host); props.put("mail.smtp.user", from); props.put("mail.smtp.password", pass); props.put("mail.smtp.port", "587"); props.put("mail.smtp.auth", "true"); props.put("mail.debug", "true"); Session session = Session.getDefaultInstance(props, null); MimeMessage message = new MimeMessage(session); Address fromAddress = new InternetAddress(from); Address toAddress = new InternetAddress("[email protected]"); message.setFrom(fromAddress); message.setRecipient(Message.RecipientType.TO, toAddress); message.setSubject("Testing JavaMail"); message.setText("Welcome to JavaMail"); Transport transport = session.getTransport("smtp"); transport.connect(host, from, pass); message.saveChanges(); Transport.send(message); transport.close(); }catch(Exception ex){ out.println("<html><head></head><body>"); out.println("ERROR: " + ex); out.println("</body></html>"); } Output on GlassFish 2.1: DEBUG SMTP: trying to connect to host "smtp.gmail.com", port 587, isSSL false 220 mx.google.com ESMTP 36sm10907668yxh.13 DEBUG SMTP: connected to host "smtp.gmail.com", port: 587 EHLO platform-4cfaca 250-mx.google.com at your service, [203.126.159.130] 250-SIZE 35651584 250-8BITMIME 250-STARTTLS 250-ENHANCEDSTATUSCODES 250 PIPELINING DEBUG SMTP: Found extension "SIZE", arg "35651584" DEBUG SMTP: Found extension "8BITMIME", arg "" DEBUG SMTP: Found extension "STARTTLS", arg "" DEBUG SMTP: Found extension "ENHANCEDSTATUSCODES", arg "" DEBUG SMTP: Found extension "PIPELINING", arg "" STARTTLS 220 2.0.0 Ready to start TLS EHLO platform-4cfaca 250-mx.google.com at your service, [203.126.159.130] 250-SIZE 35651584 250-8BITMIME 250-AUTH LOGIN PLAIN 250-ENHANCEDSTATUSCODES 250 PIPELINING DEBUG SMTP: Found extension "SIZE", arg "35651584" DEBUG SMTP: Found extension "8BITMIME", arg "" DEBUG SMTP: Found extension "AUTH", arg "LOGIN PLAIN" DEBUG SMTP: Found extension "ENHANCEDSTATUSCODES", arg "" DEBUG SMTP: Found extension "PIPELINING", arg "" DEBUG SMTP: Attempt to authenticate AUTH LOGIN 334 VXNlcm5hbWU6 aWpveWNlbGVvbmdAZ21haWwuY29t 334 UGFzc3dvcmQ6 MTIzNDU2Nzhf 235 2.7.0 Accepted DEBUG: getProvider() returning javax.mail.Provider[TRANSPORT,smtp,com.sun.mail.smtp.SMTPTransport,Sun Microsystems, Inc] DEBUG SMTP: useEhlo true, useAuth true

  Read the article

• How to fix a NHibernate lazy loading error "no session or session was closed"?

  - by MCardinale

  I'm developing a website with ASP.NET MVC, NHibernate and Fluent Hibernate and getting the error "no session or session was closed" when I try to access a child object. These are my domain classes: public class ImageGallery { public virtual int Id { get; set; } public virtual string Title { get; set; } public virtual IList<Image> Images { get; set; } } public class Image { public virtual int Id { get; set; } public virtual ImageGallery ImageGallery { get; set; } public virtual string File { get; set; } } These are my maps: public class ImageGalleryMap:ClassMap<ImageGallery> { public ImageGalleryMap() { Id(x => x.Id); Map(x => x.Title); HasMany(x => x.Images); } } public class ImageMap:ClassMap<Image> { public ImageMap() { Id(x => x.Id); References(x => x.ImageGallery); Map(x => x.File); } } And this is my Session Factory helper class: public class NHibernateSessionFactory { private static ISessionFactory _sessionFactory; private static ISessionFactory SessionFactory { get { if(_sessionFactory == null) { _sessionFactory = Fluently.Configure() .Database(MySQLConfiguration.Standard.ConnectionString(MyConnString)) .Mappings(m => m.FluentMappings.AddFromAssemblyOf<ImageGalleryMap>()) .ExposeConfiguration(c => c.Properties.Add("hbm2ddl.keywords", "none")) .BuildSessionFactory(); } return _sessionFactory; } } public static ISession OpenSession() { return SessionFactory.OpenSession(); } } Everything works fine, when I get ImageGallery from database using this code: IImageGalleryRepository igr = new ImageGalleryRepository(); ImageGallery ig = igr.GetById(1); But, when I try to access the Image child object with this code string imageFile = ig.Images[1].File; I get this error: Initializing[Entities.ImageGallery#1]-failed to lazily initialize a collection of role: Entities.ImageGallery.Images, no session or session was closed Someone know how can I fix this? Thank you very much!

  Read the article

• Is there a publicly available CDN that hosts JSON2?

  - by Xavi

  It's well known that Google and Microsoft host several common javascript libraries on their CDNs (content distribution networks). Unfortunately neither seems to host JSON2.js. I'm aware that I could upload a copy of JSON2.js to my server and serve it myself, but there are a number advantages CDNs offer that I would like to take advantage of. So with that in mind, are there any publicly available CDNs that host JSON2? If not, any idea why?

  Read the article

• Setting up a VPN connection to Amazon VPC - routing

  - by Keeno

  I am having some real issues setting up a VPN between out office and AWS VPC. The "tunnels" appear to be up, however I don't know if they are configured correctly. The device I am using is a Netgear VPN Firewall - FVS336GV2 If you see in the attached config downloaded from VPC (#3 Tunnel Interface Configuration), it gives me some "inside" addresses for the tunnel. When setting up the IPsec tunnels do I use the inside tunnel IP's (e.g. 169.254.254.2/30) or do I use my internal network subnet (10.1.1.0/24) I have tried both, when I tried the local network (10.1.1.x) the tracert stops at the router. When I tried with the "inside" ips, the tracert to the amazon VPC (10.0.0.x) goes out over the internet. this all leads me to the next question, for this router, how do I set up stage #4, the static next hop? What are these seemingly random "inside" addresses and where did amazon generate them from? 169.254.254.x seems odd? With a device like this, is the VPN behind the firewall? I have tweaked any IP addresses below so that they are not "real". I am fully aware, this is probably badly worded. Please if there is any further info/screenshots that will help, let me know. Amazon Web Services Virtual Private Cloud IPSec Tunnel #1 ================================================================================ #1: Internet Key Exchange Configuration Configure the IKE SA as follows - Authentication Method : Pre-Shared Key - Pre-Shared Key : --- - Authentication Algorithm : sha1 - Encryption Algorithm : aes-128-cbc - Lifetime : 28800 seconds - Phase 1 Negotiation Mode : main - Perfect Forward Secrecy : Diffie-Hellman Group 2 #2: IPSec Configuration Configure the IPSec SA as follows: - Protocol : esp - Authentication Algorithm : hmac-sha1-96 - Encryption Algorithm : aes-128-cbc - Lifetime : 3600 seconds - Mode : tunnel - Perfect Forward Secrecy : Diffie-Hellman Group 2 IPSec Dead Peer Detection (DPD) will be enabled on the AWS Endpoint. We recommend configuring DPD on your endpoint as follows: - DPD Interval : 10 - DPD Retries : 3 IPSec ESP (Encapsulating Security Payload) inserts additional headers to transmit packets. These headers require additional space, which reduces the amount of space available to transmit application data. To limit the impact of this behavior, we recommend the following configuration on your Customer Gateway: - TCP MSS Adjustment : 1387 bytes - Clear Don't Fragment Bit : enabled - Fragmentation : Before encryption #3: Tunnel Interface Configuration Your Customer Gateway must be configured with a tunnel interface that is associated with the IPSec tunnel. All traffic transmitted to the tunnel interface is encrypted and transmitted to the Virtual Private Gateway. The Customer Gateway and Virtual Private Gateway each have two addresses that relate to this IPSec tunnel. Each contains an outside address, upon which encrypted traffic is exchanged. Each also contain an inside address associated with the tunnel interface. The Customer Gateway outside IP address was provided when the Customer Gateway was created. Changing the IP address requires the creation of a new Customer Gateway. The Customer Gateway inside IP address should be configured on your tunnel interface. Outside IP Addresses: - Customer Gateway : 217.33.22.33 - Virtual Private Gateway : 87.222.33.42 Inside IP Addresses - Customer Gateway : 169.254.254.2/30 - Virtual Private Gateway : 169.254.254.1/30 Configure your tunnel to fragment at the optimal size: - Tunnel interface MTU : 1436 bytes #4: Static Routing Configuration: To route traffic between your internal network and your VPC, you will need a static route added to your router. Static Route Configuration Options: - Next hop : 169.254.254.1 You should add static routes towards your internal network on the VGW. The VGW will then send traffic towards your internal network over the tunnels. IPSec Tunnel #2 ================================================================================ #1: Internet Key Exchange Configuration Configure the IKE SA as follows - Authentication Method : Pre-Shared Key - Pre-Shared Key : --- - Authentication Algorithm : sha1 - Encryption Algorithm : aes-128-cbc - Lifetime : 28800 seconds - Phase 1 Negotiation Mode : main - Perfect Forward Secrecy : Diffie-Hellman Group 2 #2: IPSec Configuration Configure the IPSec SA as follows: - Protocol : esp - Authentication Algorithm : hmac-sha1-96 - Encryption Algorithm : aes-128-cbc - Lifetime : 3600 seconds - Mode : tunnel - Perfect Forward Secrecy : Diffie-Hellman Group 2 IPSec Dead Peer Detection (DPD) will be enabled on the AWS Endpoint. We recommend configuring DPD on your endpoint as follows: - DPD Interval : 10 - DPD Retries : 3 IPSec ESP (Encapsulating Security Payload) inserts additional headers to transmit packets. These headers require additional space, which reduces the amount of space available to transmit application data. To limit the impact of this behavior, we recommend the following configuration on your Customer Gateway: - TCP MSS Adjustment : 1387 bytes - Clear Don't Fragment Bit : enabled - Fragmentation : Before encryption #3: Tunnel Interface Configuration Outside IP Addresses: - Customer Gateway : 217.33.22.33 - Virtual Private Gateway : 87.222.33.46 Inside IP Addresses - Customer Gateway : 169.254.254.6/30 - Virtual Private Gateway : 169.254.254.5/30 Configure your tunnel to fragment at the optimal size: - Tunnel interface MTU : 1436 bytes #4: Static Routing Configuration: Static Route Configuration Options: - Next hop : 169.254.254.5 You should add static routes towards your internal network on the VGW. The VGW will then send traffic towards your internal network over the tunnels. EDIT #1 After writing this post, I continued to fiddle and something started to work, just not very reliably. The local IPs to use when setting up the tunnels where indeed my network subnets. Which further confuses me over what these "inside" IP addresses are for. The problem is, results are not consistent what so ever. I can "sometimes" ping, I can "sometimes" RDP using the VPN. Sometimes, Tunnel 1 or Tunnel 2 can be up or down. When I came back into work today, Tunnel 1 was down, so I deleted it and re-created it from scratch. Now I cant ping anything, but Amazon AND the router are telling me tunnel 1/2 are fine. I guess the router/vpn hardware I have just isnt up to the job..... EDIT #2 Now Tunnel 1 is up, Tunnel 2 is down (I didn't change any settings) and I can ping/rdp again. EDIT #3 Screenshot of route table that the router has built up. Current state (tunnel 1 still up and going string, 2 is still down and wont re-connect)

  Read the article

• One-to-one Mapping issue with NHibernate/Fluent: Foreign Key not updateing

  - by Trevor

  Summary: Parent and Child class. One to one relationship between the Parent and Child. Parent has a FK property which references the primary key of the Child. Code as follows: public class NHTestParent { public virtual Guid NHTestParentId { get; set; } public virtual Guid ChildId { get { return ChildRef.NHTestChildId; } set { } } public virtual string ParentName { get; set; } protected NHTestChild _childRef; public virtual NHTestChild ChildRef { get { if (_childRef == null) _childRef = new NHTestChild(); return _childRef; } set { _childRef = value; } } } public class NHTestChild { public virtual Guid NHTestChildId { get; set; } public virtual string ChildName { get; set; } } With the following Fluent mappings: Parent Mapping Id(x => x.NHTestParentId); Map(x => x.ParentName); Map(x => x.ChildId); References(x => x.ChildRef, "ChildId").Cascade.All(); Child Mapping: Id(x => x.NHTestChildId); Map(x => x.ChildName); If I do something like (pseudo code) ... HTestParent parent = new NHTestParent(); parent.ParentName = "Parent 1"; parent.ChildRef.ChildName = "Child 1"; nhibernateSession.SaveOrUpdate(aParent); Commit; ... I get an error: "Invalid index 3 for this SqlParameterCollection with Count=3" If I change the parent 'References' line as follows (i.e. provide the name of the child property I'm pointing at): References(x => x.ChildRef, "ChildId").PropertyRef("NHTestChildId").Cascade.All(); I get the error: "Unable to resolve property: NHTestChildId" So, I tried the 'HasOne()' reference setting, as follows: HasOne<NHTestChild>(x => x.ChildRef).ForeignKey("ChildId").Cascade.All().Fetch.Join(); This results in the save working, but the load fails to find the child. If I inspect the SQL Nhibernate produces I can see that NHibernate is assuming the Primary key of the parent is the link to the child (i.e. load join condition is "parent.NHTestParentId = child.NHTestChildId). The 'ForeignKey' specified appears to be ignored. I can set any value and no error occurs - the join just always fails and no child is returned. I've tried a number of slight variations on the above. It seems like it should be a simple thing to achieve. Any ideas?

  Read the article

• cuda program on VMware

  - by scatman

  i wrote a cuda program and i am testing it on ubuntu as a virtual machine. the reason for this is i have windows 7, i don't want to install ubuntu as a secondary operating system, and i need to use a linux operating system for testing. my question is: will the virtual machine limit the gpu resources? So will my cuda code be faster if i run it under my primary operating system than running it on a virtual machine?

  Read the article

• NHibernate Master-Detail and Detail Deletion.

  - by JMSA

  Role.cs public class Role { public virtual string RoleName { get; set; } public virtual bool IsActive { get; set; } public virtual IList<Permission> PermissionItems { get; set; } } Role.hbm.xml <?xml version="1.0" encoding="utf-8" ?> <hibernate-mapping xmlns="urn:nhibernate-mapping-2.2" assembly="POCO" namespace="POCO"> <class name="Role" table="Role"> <id name="ID" column="ID"> <generator class="native" /> </id> <property name="RoleName" column="RoleName" /> <property name="IsActive" column="IsActive" type="System.Boolean" /> <bag name="PermissionItems" table="Permission" cascade="all" inverse="true"> <key column="RoleID"/> <one-to-many class="Permission" /> </bag> </class> </hibernate-mapping> Permission.cs public class Permission { public virtual string MenuItemKey { get; set; } public virtual int RoleID { get; set; } public virtual Role Role { get; set; } } Permission.hbm.xml <?xml version="1.0" encoding="utf-8" ?> <hibernate-mapping xmlns="urn:nhibernate-mapping-2.2" assembly="POCO" namespace="POCO"> <class name="Permission" table="Permission"> <id name="ID" column="ID"> <generator class="native"/> </id> <property name="MenuItemKey" column="MenuItemKey" /> <property name="RoleID" column="RoleID" /> <many-to-one name="Role" column="RoleID" not-null="true" cascade="all"> </many-to-one> </class> </hibernate-mapping> Suppose, I have saved some permissions in the database by using this code: RoleRepository roleRep = new RoleRepository(); Role role = new Role(); role.Permissions = Permission.GetList(); role.SaveOrUpdate(); Now, I need this code to delete all Permissions, since role.Permissions == null. Here is the code: RoleRepository roleRep = new RoleRepository(); Role role = roleRep.Get(roleId); role.Permissions = null; role.SaveOrUpdate(); But this is not happening. What should be the correct way to cope with this situation? What/how should I change, hbm-file or persistance code?

  Read the article

• Proper 'cleartool mkview' for ClearCase Snapshot view creation

  - by Jörg Battermann

  Good afternoon, seems like I am somewhat stuck in CC-land these days, but I have one (hopefully) final question regarding proper CC-handling: When using the CC View Creation Wizard with the two steps / details below, I can create a proper Snapshot view on my machine perfectly fine, however when trying to do the same with the mkview command, it fails... Here are the screenshots of the view creation wizard: Now that results into the (working) following view: cleartool> lsview battjo6r_view2 battjo6r_view2 \\Eh40yd4c\Views\battjo6r_view2.vws cleartool> lsview -long battjo6r_view2 Tag: battjo6r_view2 Global path: \\Eh40yd4c\Views\battjo6r_view2.vws Server host: Eh40yd4c Region: CT_WORK Active: NO View tag uuid:f34cf43f.b4d048df.845d.ed:21:a2:9c:45:ff View on host: Eh40yd4c View server access path: D:\Views\battjo6r_view2.vws View uuid: f34cf43f.b4d048df.845d.ed:21:a2:9c:45:ff View attributes: snapshot View owner: WW005\battjo6r However, when trying to create the view manually via mkview -snapshot -tag battjo6r_view2 -vws \\Eh40yd4c\Views\battjo6r_view2.vws -host Eh40yd4c -hpath D:\Views\battjo6r_view2.vws -gpath \\Eh40yd4c\Views\battjo6r_view2.vws battjo6r_view2 ... I get the following error: cleartool> mkview -snapshot -tag battjo6r_view2 -vws \\Eh40yd4c\Views\battjo6r_view2.vws -host Eh40yd4c -hpath D:\Views\battjo6r_view2.vws -gpath \\Eh40yd4c\Views\battjo6r_view2.vws battjo6r_view2 Created view. Host-local path: Eh40yd4c:D:\Views\battjo6r_view2.vws Global path: \\Eh40yd4c\Views\battjo6r_view2.vws cleartool: Error: Unable to find view by uuid:6f99f7ae.6a5d40e4.ba32.37:8e:e5:a4:ed:18, last known at "<viewhost>:<stg_path>". cleartool: Error: Unable to establish connection to snapshot view "6f99f7ae.6a5d40e4.ba32.37:8e:e5:a4:ed:18": ClearCase object not found cleartool: Warning: Unable to open snapshot view "D:\SnapShotViews\battjo6r_view2". cleartool: Error: Unable to create snapshot view "battjo6r_view2". Removing the view ... Any idea why this is happening? Am I missing something?

  Read the article

• Counting and joining two tables

  - by Eikern

  Eventhosts – containing the three regular hosts and an "other" field (if someone is replacing them) eventid | host (SET[Steve,Tim,Brian,other]) ------------------------------------------- 1 | Steve 2 | Tim 3 | Brian 4 | other 5 | other Event id | other | name etc. ---------------------- 1 | | … 2 | | … 3 | | … 4 | Billy | … 5 | Irwin | … This query: SELECT h.host, COUNT(*) AS hostcount FROM host AS h LEFT OUTER JOIN event AS e ON h.eventid = e.id GROUP BY h.host Returns Steve | 1 Tim | 1 Brian | 1 other | 2 I want it to return Steve | 1 Tim | 1 Brian | 1 Billy | 1 Irwin | 1 OR Steve | | 1 Tim | | 1 Brian | | 1 other | Billy | 1 other | Irwin | 1 Can someone tell me how I can achieve this or point me in a direction?

  Read the article

• MySQL is hogging my server resources

  - by Reacen

  Does anyone have any idea of what can cause this weird behaviour and how I go about fixing it? This is all coming from MySQL only (both RAM and CPU usage), for about 10 minutes after I reboot my Java game server (that has a pool of 256 connections). There are not that many queries and I think it may be more of a MySQL misconfiguration problem. My server: 3.20 GHz * 6 core / 24 GB RAM / 64 bit Windows Server 2003. My game server: Java server, with 256 MySQL connections pool (MyISAM engine), about 500,000 accounts, and 9 million rows of game items in database and about 3,000 players are connected. After about 15 minutes of the game server reboot, the server resumes its stability and CPU usage drop down to 1% ~ 5% and memory to 6 GB. Here is a copy of my MySQL configuration. Also, any advice about my MySQL configuration will be appreciated. I really set it up almost at random. # Example MySQL config file for very large systems. # # This is for a large system with memory of 1G-2G where the system runs mainly # MySQL. # # You can copy this file to # /etc/my.cnf to set global options, # mysql-data-dir/my.cnf to set server-specific options (in this # installation this directory is C:\mysql\data) or # ~/.my.cnf to set user-specific options. # # In this file, you can use all long options that a program supports. # If you want to know which options a program supports, run the program # with the "--help" option. # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /tmp/mysql.sock # Here follows entries for some specific programs # The MySQL server [mysqld] #log=c:\mysql.log port = 3306 socket = /tmp/mysql.sock skip-locking key_buffer_size = 2572M max_allowed_packet = 64M table_open_cache = 512 sort_buffer_size = 128M read_buffer_size = 128M read_rnd_buffer_size = 128M myisam_sort_buffer_size = 500M thread_cache_size = 32 query_cache_size = 1948M # Try number of CPU's*2 for thread_concurrency thread_concurrency = 12 max_connections = 5000 # Don't listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (via the "enable-named-pipe" option) will render mysqld useless! # #skip-networking # Replication Master Server (default) # binary logging is required for replication log-bin=mysql-bin # required unique id between 1 and 2^32 - 1 # defaults to 1 if master-host is not set # but will not function as a master if omitted server-id = 1 # Replication Slave (comment out master section to use this) # # To configure this host as a replication slave, you can choose between # two methods : # # 1) Use the CHANGE MASTER TO command (fully described in our manual) - # the syntax is: # # CHANGE MASTER TO MASTER_HOST=<host>, MASTER_PORT=<port>, # MASTER_USER=<user>, MASTER_PASSWORD=<password> ; # # where you replace <host>, <user>, <password> by quoted strings and # <port> by the master's port number (3306 by default). # # Example: # # CHANGE MASTER TO MASTER_HOST='125.564.12.1', MASTER_PORT=3306, # MASTER_USER='joe', MASTER_PASSWORD='secret'; # # OR # # 2) Set the variables below. However, in case you choose this method, then # start replication for the first time (even unsuccessfully, for example # if you mistyped the password in master-password and the slave fails to # connect), the slave will create a master.info file, and any later # change in this file to the variables' values below will be ignored and # overridden by the content of the master.info file, unless you shutdown # the slave server, delete master.info and restart the slaver server. # For that reason, you may want to leave the lines below untouched # (commented) and instead use CHANGE MASTER TO (see above) # # required unique id between 2 and 2^32 - 1 # (and different from the master) # defaults to 2 if master-host is set # but will not function as a slave if omitted #server-id = 2 # # The replication master for this slave - required #master-host = <hostname> # # The username the slave will use for authentication when connecting # to the master - required #master-user = <username> # # The password the slave will authenticate with when connecting to # the master - required #master-password = <password> # # The port the master is listening on. # optional - defaults to 3306 #master-port = <port> # # binary logging - not required for slaves, but recommended #log-bin=mysql-bin # # binary logging format - mixed recommended #binlog_format=mixed # Point the following paths to different dedicated disks #tmpdir = /tmp/ #log-update = /path-to-dedicated-directory/hostname # Uncomment the following if you are using InnoDB tables #innodb_data_home_dir = C:\mysql\data/ #innodb_data_file_path = ibdata1:2000M;ibdata2:10M:autoextend #innodb_log_group_home_dir = C:\mysql\data/ # You can set .._buffer_pool_size up to 50 - 80 % # of RAM but beware of setting memory usage too high #innodb_buffer_pool_size = 384M #innodb_additional_mem_pool_size = 20M # Set .._log_file_size to 25 % of buffer pool size #innodb_log_file_size = 100M #innodb_log_buffer_size = 8M #innodb_flush_log_at_trx_commit = 1 #innodb_lock_wait_timeout = 50 [mysqldump] quick max_allowed_packet = 64M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [myisamchk] key_buffer_size = 256M sort_buffer_size = 256M read_buffer = 8M write_buffer = 8M [mysqlhotcopy] interactive-timeout

  Read the article

• Find Port Number and Domain Name to connect to Hive Table

  - by user1419563

  I am new to Hive, MapReduce and Hadoop. I am using Putty to connect to hive table and access records in the tables. So what I did is- I opened Putty and in the host name I typed- ares-ingest.vip.host.com and then I click Open. And then I entered my username and password and then few commands to get to Hive sql. Below is the list what I did $ bash bash-3.00$ hive Hive history file=/tmp/rjamal/hive_job_log_rjamal_201207010451_1212680168.txt hive> set mapred.job.queue.name=hdmi-technology; hive> select * from table LIMIT 1; So my question is- I was trying to connect to Hive Tables using Squirrel SQL Client, so in that my Connection URL is- jdbc:hive://ares-ingest.vip.host.com:10000/default. So whenever I try to connect with these attributes, I always get Hive: Could not establish connection to ares-ingest.vip.host.com:10000/default: java.net.ConnectException: Connection timed out: connect. It might be possible I am using wrong port number or domain name here. Is there any way from the command prompt I can find out these two things, like what Domain Name and Port Number(where Hive server is running) should I use to connect to Hive table from Squirrel SQL Client. As I know host and port are determined by where the hive server is running

  Read the article

• Error using httlib's HTTPSConnection with PKCS#12 certificate

  - by Remi Despres-Smyth

  Hello. I'm trying to use httplib's HTTPSConnection for client validation, using a PKCS #12 certificate. I know the certificate is good, as I can connect to the server using it in MSIE and Firefox. Here's my connect function (the certificate includes the private key). I've pared it down to just the basics: def connect(self, cert_file, host, usrname, passwd): self.cert_file = cert_file self.host = host self.conn = httplib.HTTPSConnection(host=self.host, port=self.port, key_file=cert_file, cert_file=cert_file) self.conn.putrequest('GET', 'pathnet/,DanaInfo=200.222.1.1+') self.conn.endheaders() retCreateCon = self.conn.getresponse() if is_verbose: print "Create HTTPS connection, " + retCreateCon.read() (Note: No comments on the hard-coded path, please - I'm trying to get this to work first; I'll make it pretty afterwards. The hard-coded path is correct, as I connect to it in MSIE and Firefox. I changed the IP address for the post.) When I try to run this using a PKCS#12 certificate (a .pfx file), I get back what appears to be an openSSL error. Here is the entire error traceback: File "Usinghttplib_Test.py", line 175, in t.connect(cert_file=opts["-keys"], host=host_name, usrname=opts["-username"], passwd=opts["-password"]) File "Usinghttplib_Test.py", line 40, in connect self.conn.endheaders() File "c:\python26\lib\httplib.py", line 904, in endheaders self._send_output() File "c:\python26\lib\httplib.py", line 776, in _send_output self.send(msg) File "c:\python26\lib\httplib.py", line 735, in send self.connect() File "c:\python26\lib\httplib.py", line 1112, in connect self.sock = ssl.wrap_socket(sock, self.key_file, self.cert_file) File "c:\python26\lib\ssl.py", line 350, in wrap_socket suppress_ragged_eofs=suppress_ragged_eofs) File "c:\python26\lib\ssl.py", line 113, in __init__ cert_reqs, ssl_version, ca_certs) ssl.SSLError: [Errno 336265225] _ssl.c:337: error:140B0009:SSL routines:SSL_CTX_use_PrivateKey_file:PEM lib Notice, the openSSL error (the last entry in the list) notes "PEM lib", which I found odd, since I'm not trying to use a PEM certificate. For kicks, I converted the PKCS#12 cert to a PEM cert, and ran the same code using that. In that case, I received no error, I was prompted to enter the PEM pass phrase, and the code did attempt to reach the server. (I received the response "The service is not available. Please try again later.", but I believe that would be because the server does not accept the PEM cert. I can't connect in Firefox to the server using the PEM cert either.) Is httplib's HTTPSConnection supposed to support PCKS#12 certificates? (That is, pfx files.) If so, why does it look like openSSL is trying to load it inside the PEM lib? Am I doing this all wrong? Any advice is welcome. EDIT: The certificate file contains both the certificate and the private key, which is why I'm providing the same file name for both the HTTPSConnection's key_file and cert_file parameters.

  Read the article

• MSSQL2008: DTC Transaction - Internal abort

  - by Teutales

  Hi all, I write a small own replication - a trigger which fires an DTC INSERT to another server (one reason for my own "replication": while trigger is running it calculates some data, another: it works from an express version to an express version). When I do the initial insert from the same Host with the windows authentification it works fine. But there is a webserver on another host, which uses the sqlserver login (for testing sa). When this Host do the initial insert I get a Internal abort after the entlisting and creating phase in the DTCTransaction EventClass (Profiler). The magic is: When I first fire it from the same Host with the windows authentification, I can fire it from the webserver and it works fine. But I just have to wait some minutes and it won't work. Where is my error in reasoning... Thanks! Greetz Teutales Here is my initial server script: EXEC master.dbo.sp_addlinkedserver @server = @Servername, @srvproduct=N'SQL Server' EXEC master.dbo.sp_addlinkedsrvlogin @rmtsrvname = @Servername, @locallogin = NULL , @useself = N'False', @rmtuser = @Serverlogin, @rmtpassword = @Serverpwd

  Read the article

• Static method , Abstract method , Interface method comparision ?

  - by programmerist

  When i choose these methods? i can not decide which one i must prefer or when will i use one of them?which one give best performance? First Type Usage public abstract class _AccessorForSQL { public virtual bool Save(string sp, ListDictionary ld, CommandType cmdType); public virtual bool Update(); public virtual bool Delete(); public virtual DataSet Select(); } class GenAccessor : _AccessorForSQL { DataSet ds; DataTable dt; public override bool Save(string sp, ListDictionary ld, CommandType cmdType) { } public override bool Update() { return true; } public override bool Delete() { return true; } public override DataSet Select() { DataSet dst = new DataSet(); return dst; } Second Type Usage Also i can write it below codes: public class GenAccessor { public Static bool Save() { } public Static bool Update() { } public Static bool Delete() { } } Third Type Usage Also i can write it below codes: public interface IAccessorForSQL { bool Delete(); bool Save(string sp, ListDictionary ld, CommandType cmdType); DataSet Select(); bool Update(); } public class _AccessorForSQL : IAccessorForSQL { private DataSet ds; private DataTable dt; public virtual bool Save(string sp, ListDictionary ld, CommandType cmdType) { } } } I can use first one below usage: GenAccessor gen = New GenAccessor(); gen.Save(); I can use second one below usage: GenAccessor.Save(); Which one do you prefer? When will i use them? which time i need override method ? which time i need static method?

  Read the article

• NHibernate: How to save list in the database?

  - by Anry

  I have a table Order, Transaction, Payment. Class Order has the properties: public virtual Guid Id { get; set; } public virtual DateTime Created { get; set; } ... I added properties: public virtual IList<Transaction> Transactions { get; set; } public virtual IList<Payment> Payments { get; set; } These properties contain a record of tables [Transaction] and [Payment]. How to keep these lists in the database?

  Read the article

• Creating an MJPEG Viewer Iphone

  - by Tony

  Hey all, Im trying to make a MJPEG viewer in Objective C but I'm having a bunch of issues with it. First off, Im using AsyncSocket(http://code.google.com/p/cocoaasyncsocket/) which lets me connect to the host. Here's what I got so far NSLog(@"Ready"); asyncSocket = [[AsyncSocket alloc] initWithDelegate:self]; //http://kamera5.vfp.slu.se/axis-cgi/mjpg/video.cgi NSError *err = nil; if(![asyncSocket connectToHost:@"kamera5.vfp.slu.se" onPort:80 error:&err]) { NSLog(@"Error: %@", err); } then in the didConnectToHost method: - (void)onSocket:(AsyncSocket *)sock didConnectToHost:(NSString *)host port:(UInt16)port{ NSLog(@"Accepted client %@:%hu", host, port); NSString *urlString = [NSString stringWithFormat:@"http://kamera5.vfp.slu.se/axis-cgi/mjpg/video.cgi"]; NSMutableURLRequest *request = [[[NSMutableURLRequest alloc] init] autorelease]; [request setURL:[NSURL URLWithString:urlString]]; [request setHTTPMethod:@"GET"]; //set headers NSString *_host = [NSString stringWithFormat:host]; [request addValue:_host forHTTPHeaderField: @"Host"]; NSString *KeepAlive = [NSString stringWithFormat:@"300"]; [request addValue:KeepAlive forHTTPHeaderField: @"Keep-Alive"]; NSString *connection = [NSString stringWithFormat:@"keep-alive"]; [request addValue:connection forHTTPHeaderField: @"Connection"]; //get response NSHTTPURLResponse* urlResponse = nil; NSError *error = [[NSError alloc] init]; NSData *responseData = [NSURLConnection sendSynchronousRequest:request returningResponse:&urlResponse error:&error]; NSString *result = [[NSString alloc] initWithData:responseData encoding:NSUTF8StringEncoding]; NSLog(@"Response Code: %d", [urlResponse statusCode]); if ([urlResponse statusCode] >= 200 && [urlResponse statusCode] < 300) { NSLog(@"Response: %@", result); //here you get the response } } This calls the MJPEG stream, but it doesn't call it to get more data. What I think its doing is just loading the first chunk of data, then disconnecting. Am I doing this totally wrong or is there light at the end of this tunnel? Thanks!

  Read the article

• Nhibernate One-to-one mapping issue with child object insert error

  - by TalkDotNet

  Hi, i've being banging my head against the desk all day with the following Nhibernate problem. Each bank account has one (and only one) set of rates associated with it. The primary key of the bank account table, BankAccountID is also a foreign key and the primary key in the rates table. public class BankAccount { public virtual int BankAccountId { get; set; } public virtual string AccountName { get; set;} public virtual AccountRate AccountRate {get;set;} } public class AccountRate { public virtual int BankAccountId { get; set; } public virtual decimal Rate1 { get; set; } public virtual decimal Rate2 { get; set; } } I have the following HBM mappings for BankAccount: <class name="BankAccount" table="BankAccount"> <id name ="BankAccountId" column="BankAccountId"> <generator class="foreign"> <param name="property"> AccountRate </param> </generator> </id> <property name ="AccountName" column="AccountName" /> <one-to-one name="AccountRate" class="AccountRate" constrained="true" cascade="save-update"/> </class> and the following for AccountRate: <class name="AccountRate" table="AccountRate"> <id name ="BankAccountId" column="BankAccountId"> <generator class="native" /> </id> <property name ="Rate1" column="Rate1" /> <property name ="Rate2" column="Rate2" /> </class> An existing BankAccount object can be read from the database with no problem. However, when a new BankAccount is created , the insert statement fails with; Cannot insert the value NULL into column 'BankAccountId' The issue appears to be that the child object , AccountRate is created first and since it hasn't yet got an identifier from its uncreated parent , the insert fails. I think i'm correct in saying that if the AccountRate property on BankAccount was a collection i could use the following ? Inverse=True in order to force the parent to be inserted first. Can anyone help me with this? i Really dont want to use a collection as there is only a unidirectional one to one relationship between these tables. Thanks Paul

  Read the article

• How to launch a remote process through ssh and end the connection?

  - by Lukasz Lew

  This is still blocking: ssh host nohup cmd This still leaves the connection open: ssh host nohup cmd &

  Read the article

< Previous Page | 190 191 192 193 194 195 196 197 198 199 200 201  | Next Page >