Search Results

Search found 10810 results on 433 pages for 'port forwarding'.

Page 195/433 | < Previous Page | 191 192 193 194 195 196 197 198 199 200 201 202  | Next Page >

  • SSL Mail server connection times out on send()

    - by Jivan
    When trying to programmatically send an email from a website of mine, with PHP Pear Mail package with SSL connection, PEAR:Mail replies the following : Failed to connect to example.blabla.net:PORT [SMTP: Failed to connect socket: connection timed out (code: -1, response: )] I looked for similar questions on SO and SF, all the answers asking the OP to test a request on telnet or ssh in command line. So, that is what I did and here is what happens : $ ssh -l myusername -p PORT example.blablabla.net _ Here, '_' in the second line means that NOTHING happens. Indefinitely, which seems coherent with the timeout message I had from PEAR:Mail. So PEAR:Mail seems out of cause. But, what I have to tell you is that yesterday, it just worked. Connection was properly established, mails were properly sent, etc. Just today, it doesn't work anymore and I absolutely don't know why. I restarted Apache (in case an extension was broken), restarted mail services, etc. Still. No effect. Before yesterday (when it worked) and today (when it doesn't anymore), I just didn't touch the server and did nothing on it, simply because I took a day off to write some blog post! Have anyone of you encountered similar problem ? The problem seems quite common, judging after some googling, but the solution doesn't. Thanks for any help ! (note on config : CentOS 6.4 x86_64 with cPanel/WHM)

    Read the article

  • strange raid5 issue:

    - by 8steve8
    ok so ive had a 4x2TB(samsung HD204UI w/firmware patch) raid5 array working normally for about a month. It was in a h57 gigabyte motherboard using the intel raid with windows 7 x64. Today I got an intel h67 motherboard, so I upgraded the intel raid drivers to 10.1.0.1008 from 9.6.0.1014, and I'm not sure if i checked after a reboot, but it caused no problems. I swapped in the new dh67 motherboard, and my array status was "failed". 2 of the 4 drives listed themselves as members, while the other two drives listed themselves as non-members. I tried going back to the old h57 mobo, and downgrading the raid drivers, but the issue remains. It's not port dependent, 2 of the drives always come up as non-members regardless of what port or motherboard they are plugged into. the screenshot should show that the SNs match, which begs the question why the software doesn't realize the drive is a member of the array: http://img837.imageshack.us/img837/6145/both.png I'd like to know if anyone has experienced anything similar, and what should i do, can i force the drive to be recognized as a member (without wiping data)?

    Read the article

  • disable specific PCI device at boot

    - by Rhymoid
    I've just reinstalled Debian on my Sony VAIO laptop, and my dmesg and virtual consoles all get spammed with the same messages over and over again. [ 59.662381] hub 1-1:1.0: unable to enumerate USB device on port 2 [ 59.901732] usb 1-1.2: new high-speed USB device number 91 using ehci_hcd [ 59.917940] hub 1-1:1.0: unable to enumerate USB device on port 2 [ 60.157256] usb 1-1.2: new high-speed USB device number 92 using ehci_hcd I believe these messages are coming from an internally connected USB device, most likely the webcam (since that's the only thing that doesn't work). The only way I can seem to have it shut up (without killing my actually useful USB ports) is to disable one of the USB host controllers: # echo "0000:00:1a.0" > /sys/bus/pci/drivers/ehci_hcd/unbind This also takes down my Bluetooth interface, but I'm fine with that. I would like this setting to persist, so that I can painlessly use my virtual console again in case I need it. I want my operating system (Debian amd64) to never wake it up, but I don't know how to do this. I've tried to blacklist the module alias for the PCI device, but it seems to be ignored: $ cat /sys/bus/pci/devices/0000\:00\:1a.0/modalias pci:v00008086d00003B3Csv0000104Dsd00009071bc0Csc03i20 $ cat /etc/modprobe.d/blacklist blacklist pci:v00008086d00003B3Csv0000104Dsd00009071bc0Csc03i20 How do I ensure that this specific PCI device is never automatically activated, without disabling its driver altogether? -edit- The module was renamed recently, now the following works from userland: echo "0000:00:1a.0" > /sys/bus/pci/drivers/ehci-pci/unbind Still, I'm looking for a way to stop the kernel from binding that device in the first place.

    Read the article

  • Windows 7: Dual Monitor Issue

    - by sdoca
    I have a Dell laptop with a docking station and two external monitors hooked up. I'm running Windows 7 64 bit. Originally, the two monitors were the same - Dell 1908FP. I have replaced one of them with an HP LA2405. I have set the HP 24" (1920 x 1200 connected via DVI port) as montior 1 and extended to use the Dell 19" (12080 x 1024 connected via VGA port) as monitor 2. I have set my power plan so that when the laptop is plugged in, it will turn the monitors off after 10 minutes, but it will not put my laptop to sleep. However, now that I have the HP monitor, when I unlock my laptop and the monitors come back on, all my windows are resized and shifted to the top left corner of the HP monitor as if they had been resized for display on the smaller Dell monitor. A co-worker has the exact same laptop and monitor configuration but doesn't experience this issue, so I figure there's some configuration that's different but we can't find it. I haven't been able to find any mention of a similar problem doing an internet search, but I'm not really sure what terms to use in my search. Anybody have any suggestions as to what may be causing the issue? OS setting? Monitor setting? EDIT: My laptop is using the Intel Graphics and Media Control Panel/drivers.

    Read the article

  • wireless clients not getting correct dhcp addresses

    - by szeli
    I apologise first if this is a stupid problem. I'm new to Cisco networking. I need some help with an existing configuration done by my vendor. Environment: 1. Core switch - Catalyst 6509e vlans configured: a. vlan 50 (wired clients) 10.0.50.x/24 interface IP 10.0.50.20 b. vlan 70 (wireless clients) 10.0.70.x/24 interface IP 10.0.70.20 c. vlan 192 (guest clients) 192.168.1.x/24 interface IP 192.168.1.20 d. trunk port for WLC native vlan 70 allowed vlan 50, 70, 192 2. Cisco 4402 WLC interfaces a. management untagged IP 10.0.70.10 b. ap-manager untagged IP 10.0.70.11 c. service-port n/a IP 192.168.10.1 d. virtual n/a IP 1.1.1.1 e. guestwlan vlan192 IP 192.168.1.100 3. Cisco AIR-LAP1142N-S-K9 LAP01 (WLAN local, interface: management) IP 10.0.70.21/24 GW 10.0.70.20 DHCP server 10.0.50.10 (scope 10.0.70.101 to 200) LAP02 (WLAN guest, interface: guestwlan) IP 192.168.1.21/24 GW 192.168.1.20 DHCP server 192.168.1.10 (scope 192.168.1.101 to 200) here's the problem, wireless clients connected to WLAN guest keep getting DHCP leases from WLAN local 10.0.50.10 (scope 10.0.70.101 to 200) can anyone please help? thanks!

    Read the article

  • IIS 6.0 https not working "connection was reset"

    - by cad
    Application Server Windows Server 2003 SP2 with IIS 6.0 IIS has a "Default Web Site" (port 18000, ssl 443, ID=1) with a certificate created by me. I have an specific site called "scj.galaxy.Weekly" (port 80, ssl 443, ID=1272369728) that is working fine. I have an entry in windows/system32/drivers/etc/hosts that links galaxy.Weekly.scjdev.ds to the server ip in both my local machine and in the application Server. These sites works: http://scj.galaxy.weekly/test.html works http://scj.galaxy.weekly/test.aspx works But https://scj.galaxy.weekly/test.html fails Error message is: The connection was reset The connection to the server was reset while the page was loading. The certificate was working fine for months. It was created with something similar to this: Selfssl /N:CN=*.scjdev.ds /V:3650 /S:1 /P:443 I have tried several options and none of them are working: 1) Create a certificate only in "Default Web Site" and link it to SecureBindings with command prompt cscript adsutil.vbs set /w3svc/1272369728/SecureBindings ":443:galaxy.Weekly.scjdev.ds" 2) Create a certificate only in "Galaxy Site" and link it to SecureBindings 3) Create a certificate in both and link them to secureBindings. Probably I am missing an step or something, but I can't see it. Here is the relevant config of Galaxy Site: <IIsWebServer Location ="/LM/W3SVC/1272369729" AuthFlags="0" LogPluginClsid="{FF160663-DE82-11CF-BC0A-00AA006111E0}" SSLCertHash="c36a514a0be90fbc121d9c19bb052842289d5aee" SSLStoreName="MY" SecureBindings=":443:galaxy.Weekly.scjdev.ds" ServerAutoStart="TRUE" ServerBindings=":80:galaxy.Weekly.scjdev.ds" ServerComment="galaxy.Weekly.scjdev.ds" > </IIsWebServer> <IIsWebVirtualDir Location ="/LM/W3SVC/1272369729/root" AccessFlags="AccessRead | AccessScript" AppFriendlyName="Default Application" AppIsolated="2" AppRoot="/LM/W3SVC/1272369729/Root" AuthFlags="AuthAnonymous | AuthNTLM" DefaultDoc="Default.aspx" DirBrowseFlags="EnableDirBrowsing | DirBrowseShowDate | DirBrowseShowTime | DirBrowseShowSize | DirBrowseShowExtension | DirBrowseShowLongDate" Path="D:\Webs\Galaxysite" ScriptMaps="some config... " > </IIsWebVirtualDir>

    Read the article

  • iptables rules for DNS/Transparent proxy with ip exceptions

    - by SlimSCSI
    I am running a router (A Netgear WNDR3700 if that matters) with dd-wrt. For content filtering I am using OpenDNS. I wanted to make sure a user could not bypass OpenDNS by putting in their own name servers, so I have a rule to catch all DNS traffic. iptables -t nat -A PREROUTING -i br0 -p all --dport 53 -j DNAT --to $LAN_IP I did have one computer on the network I wanted to allow past OpenDNS filters. On that machine I manually set the name servers, and created another rule to allow it to pass iptables -t nat -I PREROUTING -i br0 -s 192.168.1.2 -j ACCEPT This worked well. Today, I installed a transparent proxy (squid) on the router and added these rules: iptables -t nat -A PREROUTING -i br0 -s $LAN_NET -d $LAN_NET -p tcp --dport 80 -j ACCEPT iptables -t nat -A PREROUTING -i br0 -s ! $PROXY_IP -p tcp --dport 80 -j DNAT --to $PROXY_IP:$PROXY_PORT iptables -t nat -I POSTROUTING -o br0 -s $LAN_NET -d $PROXY_IP -p tcp -j SNAT --to $LAN_IP iptables -I FORWARD -i br0 -o br0 -s $LAN_NET -d $PROXY_IP -p tcp --dport $PROXY_PORT -j ACCEPT This also works, however the 192.168.1.2 address does not get routed through squid. How can I have 192.168.1.2 (and maybe others in the future) by-pass the port 53 rules, but not the port 80 rules?

    Read the article

  • Allow SFTP in iptables

    - by Kevin Orriss
    I have just purchased a VPS from linode and am going through the setup guide. I have everything running (apache2, php, mysql etc) but I am being denied access via SFTP when using fileZilla to upload a file. Now this is my second time installing the server as I missed a section out the first time. I was able to connect to my server through SFTP on filezilla the first time and the thing I missed out was adding a new user and editing the iptables in the firewall. So it would seem that the guide I have been following has blocked SFTP but allowed SSH. Here is the iptables file: *filter # Allow all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT ! -i lo -d 127.0.0.0/8 -j REJECT # Accept all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow all outbound traffic - you can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allow HTTP and HTTPS connections from anywhere (the normal ports for websites and SSL). -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allow SSH connections # # The -dport number should be the same port number you set in sshd_config # -A INPUT -p tcp -m state --state NEW --dport 22 -j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # Log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT All I would like is a line I need to put in there which allows SFTP over port 22. Thank you for reading this.

    Read the article

  • Preventing back connect in Cpanel servers

    - by Fernando
    We run a Cpanel server and someone gained access to almost all accounts using the following steps: 1) Gained access to an user account due to weak password. Note: this user didn't had shell access. 2) With this user account, he accessed Cpanel and added a cron task. The cron task was a perl script that connected to his IP and he was able to send back shell commands. 3) Having a non jailed shell, he was able to change content of most websites in server specially for users who set their folders to 777 ( Unfortunately a common recommendation and sometimes a requirement for some PHP softwares ). Is there a way to prevent this? We started by disabling cron in Cpanel interface, but this is not enough. I see a lot of other options in which an user could run this perl script. We have a firewall running and blocking uncommon outgoing ports. But he used port 80 and, well, I can't block this port as a lot of processes use them to access things, even Cpanel itself.

    Read the article

  • IPTABLES syntax help to forward Remote Desktop requests to a VM [CentOS host]

    - by NVRAM
    I've a VM running MSWindows XP hosted on my CentOS 5.4 machine. I can rdesktop into it from the hosting machine and work just fine using the private ddress (192.168.122.65), but I now need to allow Remote Desktop access from other computers (not just the machine hosting the VM). [Edit] I only need to allow access for a day or so, so don't want to add a NIC (for XP activation reasons). Could someone help me with the iptables syntax? The VM is on a private/virtual network: 192.168.122.65 and my CentOS machine is on a physical network, at 10.1.3.38 (and 192.168.122.1 as the GW for the virtual net). I found this question, but none of the answers seemed to work and I'm a bit timid at blindly trying variations. My FORWARD rules are as listed. Thanks in advance. # iptables -L FORWARD Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable RH-Firewall-1-INPUT all -- anywhere anywhere [Edit] If I do play "blindly" is there a simple way to reset the settings on CentOS (a la service network restart)?

    Read the article

  • How to make lighttpd respect X-Forwarded-Proto when constructing redirects for directories?

    - by Tim Landscheidt
    We have an nginx proxy at tools.wmflabs.org that receives requests by http and https and passes them by http on to lighttpds on a grid (one lighttpd per top-level path). Requests that reach the proxy by https are received by the lighttpds like this: HEAD /lighttpd-test/test HTTP/1.1 Connection: close Host: tools.wmflabs.org X-Forwarded-Proto: https X-Original-URI: /lighttpd-test/test User-Agent: curl/7.29.0 Accept: */* This works great except in the case where the URL references a physical directory and misses the trailing slash ("/"), as lighttpd then generates a redirect to the http URL: HTTP/1.1 301 Moved Permanently Location: http://tools.wmflabs.org/lighttpd-test/test/ Connection: close Date: Fri, 06 Jun 2014 14:50:29 GMT Server: lighttpd/1.4.28 The relevant parts of our lighttpd configurations are: server.modules = ( "mod_setenv", "mod_access", "mod_accesslog", "mod_alias", "mod_compress", "mod_redirect", "mod_rewrite", "mod_fastcgi", "mod_cgi", ) server.port = $port [...] server.document-root = "$home/public_html" [...] server.follow-symlink = "enable" [...] server.stat-cache-engine = "fam" ssl.engine = "disable" alias.url = ( "/$tool" => "$home/public_html/" ) index-file.names = ( "index.php", "index.html", "index.htm" ) dir-listing.encoding = "utf-8" server.dir-listing = "disable" url.access-deny = ( "~", ".inc" ) [...] How can I make lighttpd respect X-Forwarded-Proto and use it when constructing redirects for directories? I'm aware that I could try to tackle this in nginx, but I'd prefer if I can fix it in lighttpd.

    Read the article

  • Which Cardbus/PCMCIA -> USB card works with external hard drive?

    - by Carl
    I have an HT-Link Cardbus/PCMCIA USB 2.0 2-port card (NEC / 32-bit). My external hard drive w/USB adapter won't work with it, and it will work plugged directly into a USB port on a different laptop. (My USB ports got fried.) I got the card off E-Bay. My MP3 player works plugged into that card. The drivers for the card say "Known limitations: High Speed Isochronus, USB Composite Devices." (No other details provided.) I don't know if the hard drive adapter is "isochronous" or "composite." I've read there are problems with too little power being supplied to the drive. The cable to the drive has two USB plugs on one end, and it doesn't make any difference if I plug both of them into the Cardbus card. What card should I get? I see many different brands on E-Bay. I need one that supplies sufficient power for an external hard drive, and doesn't have any "known limitations" in the way.

    Read the article

  • strange raid5 issue: [closed]

    - by 8steve8
    ok so ive had a 4x2TB(samsung HD204UI w/firmware patch) raid5 array working normally for about a month. It was in a h57 gigabyte motherboard using the intel raid with windows 7 x64. Today I got an intel h67 motherboard, so I upgraded the intel raid drivers to 10.1.0.1008 from 9.6.0.1014, and I'm not sure if i checked after a reboot, but it caused no problems. I swapped in the new dh67 motherboard, and my array status was "failed". 2 of the 4 drives listed themselves as members, while the other two drives listed themselves as non-members. I tried going back to the old h57 mobo, and downgrading the raid drivers, but the issue remains. It's not port dependent, 2 of the drives always come up as non-members regardless of what port or motherboard they are plugged into. the screenshot should show that the SNs match, which begs the question why the software doesn't realize the drive is a member of the array: http://img837.imageshack.us/img837/6145/both.png I'd like to know if anyone has experienced anything similar, and what should i do, can i force the drive to be recognized as a member (without wiping data)?

    Read the article

  • iptables, forward traffic for ip not active on the host itself

    - by gucki
    I have kvm guest which's netword card is conntected to the host using a tap device. The tap device is part of a bridge on the host together with eth0 so it can access the public network. So far everything works, the guest can access the public network and it can be accessed from the public network. Now the kvm process on the host provides a vnc server for the guest which listens on 127.0.0.1:5901 on the host. Is there any way to make this vnc server accessible by the ip address which the guest is using (ex. 192.168.0.249), without interrupting the guest from using the same ip (port 5901 is not used by the guest)? It should also work when the guest is not using any ip address at all. So basically I just want to fake IP xx is on the host and only answer/ forward traffic to port 5901 to the host itself. I tried using this NAT rule on the host, but it doesn't work. Ip forwarding is enabled at the host. iptables -t nat -A PREROUTING -p tcp --dst 192.168.0.249 --dport 5901 -j DNAT --to-destination 127.0.0.1:5901 I assume this is because the IP 192.168.0.249 is not not bound to any interfaces and so no ARP requests for it get answered and so no packets for this IP arrive at the host. How can make it work? :)

    Read the article

  • Server periodically freezing - Help Stabilizing

    - by JonDog
    We run an asp.net/sql server data collection website with a hand full of clients dumping data in and running reports. We moved to a new server (specs below) and have had issues with it freezing and having to reboot it a dozen times over the pass six months. The hosting company has mentioned possible causes (listed below) but cant give a definite answer on what is going wrong. They have offered to reconfigure how ever I like. We have benefited from having a much faster system and really dont want to get rid of the ssd's unless they are the issue. Two possible setup changes that I've talked with them about are also listed below. Any suggestions on what maybe causing the freezing issue as well as suggestion on a new setup would be great. My main questions are: Do SSD generally have problems running the OS & SQL Server on the same RAID Array? and Are the new SSD's still unrefined enough to be running in a production environment? Thanks Current: Xeon Quad Core E3-1270 3.40 Ghz 16 GB DDR3-1333 ECC SDRAM First Hard Drive: 120GB Intel SSD Second Hard Drive: 120GB Intel SSD Third Hard Drive: 120GB Intel SSD Fourth Hard Drive: 120GB Intel SSD SAS 4 Port RAID Card Windows 2012 Standard Edition - 64 Bit MSSQL 2008 Web Edition Possible Causes: Running Sql Server & OS on same RAID Array OS Software Issues Using SSD's CPU Underpowered Not enough RAM Option 1 2x Xeon Quad Core E5-2603 1.80 GHz 16 GB DDR3-1333 ECC SDRAM 1 x 240GB Intel SSD - OS 3 x 1 TB SATA HDD (7200 RPM) - SQL Server SATA 4 Port RAID Card Windows 2012 Standard Edition - 64 Bit Option 2 Dell PowerEdge E3-1270v2 3.5GHz 4 Cores 16 GB DDR3-1600 UDIMM 4 x 128 GB Samsung 840 Pro SSD Add-in H200 (SAS/SATA Controller), 4 Hard Drives - RAID 10 Windows 2012 Standard Edition - 64 Bit

    Read the article

  • Apache not routing to tomcat on correct Virtual host

    - by ttheobald
    We are looking at moving from Websphere to Tomcat. I'm trying to send traffic to tomcat from apache web server based on the virtual host directives in apache web server. After some playing around I have it sort of working, but I'm noticing that if I have a JKMount directive in the first VirtualHost in apache, all virtualHosts will send to the application server. If I have the JKMount in Virtual hosts further down in the configs, then only that VirtualHost works with the request. For Example, with the configs below here are my symptoms mysite.com/Webapp1/ -- I resolve to the proper application mysite2.com/Webapp1/ -- I resolve to the proper application (bad!) mysite.com/MonitorApp/ -- I resolve to the proper application mysite2.com/MonitorApp/ -- I resolve to the proper application (bad!) mysite.com/Webapp2/ -- I DO NOT get to the app (good) mysite2.com/Webapp2/ -- I resolve to the proper application Here's what my web server virtualhosts look like. <VirtualHost 255.255.255.1:80> ServerName mysite.com ServerAlias aliasmysite.ca ##all our rewrite rules JkMount /Webapp1/* LoadBalanceWorker JKmount /MonitorApp/* LoadBalanceWorker </VirtualHost> <VirtualHost 255.255.255.2:80> ServerName mysite2.com ServerAlias aliasmysite2.ca ##all our rewrite rules JkMount /Webapp2/* LoadBalanceWorker </VirtualHost> we are running apache webserver 2.2.10 and tomcat 7.0.29 on Solaris10 I've posted an image of our architecture here. http://imgur.com/IFaA6Rh I HAVE not defined VirtualHosts on Tomcat. Based on what I've read, my understanding is that it's only needed if I'm accessing Tomcat directly. Any assistance is appreciated. Edit Here's my worker.properties. worker.list= LoadBalanceWorker,App1,App2 worker.intApp1.port=8009 worker.intApp1.host=10.15.8.8 worker.intApp1.type=ajp13 worker.intApp1.lbfactor=1 worker.intApp1.socket_timeout=30 worker.intApp1.socket_connect_timeout=5000 worker.intApp1.fail_on_status=302,500,503 worker.intApp1.recover_time=30 worker.intApp2.port=8009 worker.intApp2.host=10.15.8.9 worker.intApp2.type=ajp13 worker.intApp2.lbfactor=1 worker.intApp2.socket_timeout=30 worker.intApp2.socket_connect_timeout=5000 worker.intApp2.fail_on_status=302,500,503 worker.intApp2.recover_time=30 worker.LoadBalanceWorker.type=lb worker.LoadBalanceWorker.balanced_workers=intApp1,intApp2 worker.LoadBalanceWorker.sticky_session=1

    Read the article

  • How can I get Solr listening on 0.0.0.0 instead of just localhost?

    - by Neil
    I'm trying to get Solr to listen on 0.0.0.0 instead of just localhost, and it doesn't seem to be picking up the configuration options. I downloaded apache-solr-1.4.1 from the Solr website, and I'm running: user@:apache-solr-1.4.1/example $ java -jar start.jar With these configuration options: <Call name="addConnector"> <Arg> <New class="org.mortbay.jetty.bio.SocketConnector"> <Set name="host"><SystemProperty name="jetty.host" default="0.0.0.0" /></Set> <Set name="port"><SystemProperty name="jetty.port" default="8983" /></Set> <Set name="maxIdleTime">50000</Set> <Set name="lowResourceMaxIdleTime">1500</Set> </New> </Arg> </Call> Where the only line changed from the default is this one: <Set name="host"><SystemProperty name="jetty.host" default="0.0.0.0" /></Set> And when I check netstat, I see this: $ netstat -an | egrep 'Proto|\b8983\b' Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:8983 0.0.0.0:* LISTEN tcp6 0 0 ::1:8983 :::* LISTEN Where Local Address should be 0.0.0.0:8983 instead of 127.0.0.1:8983. Does anyone know why this might not be working?

    Read the article

  • Routing Traffic With OpenVPN

    - by user224277
    Few minutes ago i configured my VPN server, and actually I can connect to my VPN but all trafic is going through my normal home network. On my OpenVPN application I've got an information : Server IP: **.185.***.*10 Client IP: 10.8.0.6 Traffic: 7.3 KB in, 5.6 KB out Connected: 10 June 2014 19:21:59 So everything is connected but how I can setup on windows 7 that all trafic have to go through OpenVPN network card ?? Client setting : client dev tun proto udp # enter the server's hostname # or IP address here, and port number remote **.185.***.*10 1194 resolv-retry infinite nobind persist-key persist-tun # Use the full filepaths to your # certificates and keys ca ca.crt cert user1.crt key user1.key ns-cert-type server comp-lzo verb 6 Server setting : port 1194 proto udp dev tun # the full paths to your server keys and certs ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/server.crt key /etc/openvpn/keys/server.key dh /etc/openvpn/keys/dh2048.pem cipher BF-CBC # Set server mode, and define a virtual pool of IP # addresses for clients to use. Use any subnet # that does not collide with your existing subnets. # In this example, the server can be pinged at 10.8.0.1 server 10.8.0.0 255.255.255.0 # Set up route(s) to subnet(s) behind # OpenVPN server push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" ifconfig-pool-persist /etc/openvpn/ipp.txt keepalive 10 120 status openvpn-status.log verb 6 and sysctl : net.ipv4.ip_forward=1 Thank you for your time and help.

    Read the article

  • setting up vpn server

    - by Lock
    I need help in visualising how to setup our VPN box when we move to our new network with Telstra. We have a safe@office 500P, which has a public IP and a private IP of 192.168.19.2. It is physically connected to our router, which has 4 different interfaces, one being 192.168.19.1. On the VPN box, we have a static route to forward everything to 192.168.19.1 which is the router, and from there it works out where to go. Now, we are moving to a Telstra WAN and things are setup a little differently. Our head office router has only 3 interfaces- 1 is for the link to the switch that has the fibre connection (so our route to the internet and other branches), 1 is for our 10.10.20.x network and one is for the local branch network. I really have no idea how to set this up as with the new setup, we will not have a port for it to plug into on the router. Could I just plug it into the 10.10.20.x network? Would I have to give it a public IP or can we just forward through the ports that it would use? Another suggestion was to VLAN our switch into two networks- one for the 10.10.20.x network and one for the network the VPN currently sits on (192.168.19.x), and setup the router to trunk between the port and the switch. Not sure how to do this. Sorry VPN's are definitely not my strong suit. Any advice appreciated!

    Read the article

  • Need recommendation: which USB card (PCMCIA) works with external hard drive?

    - by Carl
    I have an HT-Link Cardbus/PCMCIA USB 2.0 2-port card (NEC / 32-bit). My external hard drive w/USB adapter won't work with it, and it will work plugged directly into a USB port on a different laptop. (My USB ports got fried.) I got the card off E-Bay. My MP3 player works plugged into that card. The drivers for the card say "Known limitations: High Speed Isochronus, USB Composite Devices." (No other details provided.) I don't know if the hard drive adapter is "isochronous" or "composite." I've read there are problems with too little power being supplied to the drive. The cable to the drive has two USB plugs on one end, and it doesn't make any difference if I plug both of them into the Cardbus card. What card should I get? I see many different brands on E-Bay. I need one that supplies sufficient power for an external hard drive, and doesn't have any "known limitations" in the way.

    Read the article

  • Passive mode FTP file download hangs from specific machine

    - by chiptuned
    I have a server which is an AWS instance that just cannot download files from a specific FTP server. I can connect to the FTP server fine and run some commands, but when I request a file it just hangs. Here is the debug output of the base linux ftp client after login: ---> SYST 215 UNIX Type: Apache FtpServer Remote system type is UNIX. ftp> get outgoing/catalog.gz catalog.gz local: catalog.gz remote: outgoing/catalog.gz ---> PASV 227 Entering Passive Mode (64,156,167,125,135,191) ---> RETR outgoing/catalog.gz 150 File status okay; about to open data connection. Thats it. Then it just sits there and nothing transfers. I have verified that a data connection is made but the client gets no data. ? ss -nt dst 64.156.167.125 State Recv-Q Send-Q Local Address:Port Peer Address:Port ESTAB 0 0 10.185.147.150:41190 64.156.167.125:21 ESTAB 0 0 10.185.147.150:48871 64.156.167.125:48557 The FTP server is not in my control and downloads from other FTP servers in passive mode have worked. Active mode does not work as the system is behind a firewall. Every FTP client I've tried has the same problem. The download works from other systems, even from other AWS instances I have with the same Security Group. Not necessarily the same distro or config though. I understand it may be some issue on the server side, but I want to know what it is about my particular machine where the transfer hangs and where on every other machine I can get my hands on, it works. Please let me know what the culprit on the client side could be or ideas on what else to look at.

    Read the article

  • What ports, besides 80, need to be available to send (only send) email using phpmailer to gmail over SSL?

    - by Wobblefoot
    Using phpmailer I keep getting a 110 timeout and "Unable to connect to host" when sending email from my web server. The authentication details are right and they work on another server I have (login, pwd, ports etc and gmail acct set up for SSL connections on 465), but it's failing on my new server. FIREWALL: I allow related/established, port 80 and a port for SSH on INPUT, then this on OUTPUT: 7906 474K DROP tcp -- any any anywhere anywhere tcp dpt:smtp 0 0 ACCEPT tcp -- any any localhost.localdomain yw-in-f109.1e100.net tcp dpt:submission 0 0 ACCEPT tcp -- any any localhost.localdomain gx-in-f109.1e100.net tcp dpt:ssmtp 0 0 DROP tcp -- any any anywhere anywhere tcp dpt:submission 9 540 DROP tcp -- any any anywhere anywhere tcp dpt:ssmtp This output chain works on my other server and disabling it doesn't get mail delivered either. WEB SERVER: Varnish (80) Nginx (8088) Drupal 7 PHP5-FPM APC MySQL All works beautifully, except for outgoing email. What else could it be? I understand phpmailer does NOT require a local MTA or procmail (this is sort of the point - I don't want the security or admin overhead of a full blown MTA on my web server). Am I wrong? Do I need an MTA as well? What local ports and programs are used to authenticate over SSL and route mail using phpmailer? Any ideas at all greatly appreciated - wasted a day on this nonsense already!

    Read the article

  • What Logs / Process Stats to monitor on a Ubuntu FTP server?

    - by Adam Salkin
    I am administering a server with Ubuntu Server which is running pureFTP. So far all is well, but I would like to know what I should be monitoring so that I can spot any potential stability and security issues. I'm not looking for sophisticated software, more an idea of what logs and process statistics are most useful for checking on the health of the system. I'm thinking that I can look at various parameters output from the "ps" command and compare to see if I have things like memory leaks. But I would like to know what experienced admins do. Also, how do I do a disk check so that when I reboot, I don't get a message saying something like "disk not checked for x days, forcing check" which delays the reboot? I assume there is command that I can run as a cron job late at night. How often should it be run? What things should I be looking at to spot intrusion attempts? The only shell access is SSH on a non-standard port through UFW firewall, and I regularly do a grep on auth.log for "Fail" or "Invalid". Is there anything else I should look at? I was logging the firewall (UFW) but I have very few open ports (FTP and SSH on a non standard port) so looking at lists of IP's that have been blocked did not seem useful. Many thanks

    Read the article

  • Strategy to isolate multiple nginx ssl apps with single domain via suburi's?

    - by icpu
    Warning: so far I have only learnt how to use nginx to serve apps with their own domain and server block. But I think its time to dive a little deeper. To mitigate the need for multiple SSL certificates or expensive wildcard certificates I would like to serve multiple apps (e.g. rails apps, php apps, node.js apps) from one nginx server_name. e.g. rooturl/railsapp rooturl/nodejsapp rooturl/phpshop rooturl/phpblog I am unsure on ideal strategy. Some examples I have seen and or thought about: Multiple location rules, this seems to cause conflicts between the individual app config requirements, e.g. differing rewrite and access requirements Isolated apps by backend internal port, is this possible? Each port routing to its own config? So config is isolated and can be bespoke to app requirements. Reverse proxy, I am little ignorant of how this works, is this what I need to research? is this actually 2 above? Help online seems to always proxy to another server e.g apache What is an effective way to isolate config requirements for apps served from a single domain via sub uris?

    Read the article

  • Website is not accessible from server which is using proxy

    - by Bhoot
    I hosted a website in a win 2008 R2 server which runs in private domain. I set up bindings for port 80 and 443 for http & https respectively. Created inbound rule for port 80 and 443 also in windows firewall. After doing all this, i am still not able to access my website from remote machine. IE : Internet Explorer cannot display the webpage. Chrome : Oops! Google Chrome could not find xxxxxx Tried accessing website by ip address but no luck. I tried to ping that server but it says TTL expired in Transit. Now i found some more information over internet to check if the server is using any kind of proxy in between. I found my IP address at www.getip.com, but ipconfig/all gives me a different IP address. Is it really a problem if we use proxy ? I am not sure if i have concluded it correctly. But is there any way out to resolve this issue? Update ::: I figured it out. I have to call that website with external IP address. due to the proxy settings i was not able to call that website by the server's IP or name of that machine.

    Read the article

< Previous Page | 191 192 193 194 195 196 197 198 199 200 201 202  | Next Page >