Search Results

Search found 10810 results on 433 pages for 'port forwarding'.

Page 191/433 | < Previous Page | 187 188 189 190 191 192 193 194 195 196 197 198  | Next Page >

  • SSH connection problem - allowed from LAN but not WAN

    - by Kerem Ulutas
    I tried to setup my Arch Linux installation to be an SSH host, but here is the thing: I can ssh localhost, it fails to login via public key and asks for username and password, but still able to login. When I try ssh my_wan_ip it gives ssh_exchange_identification: Connection closed by remote host error. I've read all topics about this error and none helped me. By the way, just confirmed, it gives ssh: connect to host my_dyndns_hostname port 22: Connection refused from another machine (outside of my network, it has different wan ip). I have sshd: ALL in "hosts.allow", ALL:ALL in "hosts.deny". I am able to connect to my own pc via ssh, ping my own pc, but my ssh setup seems to be the problem, it gives that annoying error when I try to ssh from wan. /etc/ssh/ssh_config /etc/ssh/sshd_config And finally, here is the debug output for both sshd and ssh: (i ran ssh command and i took output to sshd debug after that): sshd debug ssh debug I can edit my question according to your needs. Just ask for any more information needed. BTW I have no iptables running. I have one cable dsl modem connected to a asus wl-330gE wireless access point, they both have their firewall disabled. I configured NAT so port 22 is directed to the pc I'm having this trouble. Any help appreciated, thanks..

    Read the article

  • Connect to Apache times out randomly

    - by Amadan
    We are trying to set up an Apache server on a remote machine, but we experience strange behaviour. Checking with telnet remote.machine 80, one of these things happen randomly: Connect and serve content normally (no delay) Connect after a long pause Connect normally, then time out without response Timeout on connect Once connected, the request seems to be processed normally. These things do not occur if I connect from that machine directly to localhost 80. The Apache is dedicated, as is the server it runs on (runs only this one application, no-one else is using it for anything else). I am not an administrator of the remote site, and I do not know the network architecture over there, but apparently it's firewalled: (HTTP port is open, SSH port is IP-restricted, most others are closed). If there was any one pattern, I might have some ideas, but this variety of symptoms baffles me. Any ideas as to what could be causing this? Apache is 2.2; Server version is: Linux version 2.6.9-22.ELsmp ([email protected]) (gcc version 3.4.4 20050721 (Red Hat 3.4.4-2)) #1 SMP Mon Sep 19 18:32:14 EDT 2005

    Read the article

  • fail2ban regex working but no action being taken

    - by fpghost
    I have the following snippet of fail2ban configuration on Ubuntu 13.10 server: #jail.conf [apache-getphp] enabled = true port = http,https filter = apache-getphp action = iptables-multiport[name=apache-getphp, port="http,https", protocol=tcp] mail-whois[name=apache-getphp, dest=root] logpath = /srv/apache/log/access.log maxretry = 1 #filter.d/apache-getphp.conf [Definition] failregex = ^<HOST> - - (?:\[[^]]*\] )+\"(GET|POST) /(?i)(PMA|phptest|phpmyadmin|myadmin|mysql|mysqladmin|sqladmin|mypma|admin|xampp|mysqldb|mydb|db|pmadb|phpmyadmin1|phpmyadmin2|cgi-bin) ignoreregex = I know the regex is good, because if I run the test command on my access.log: fail2ban-regex /srv/apache/log/access.log /etc/fail2ban/filter.d/apache-getphp.conf I get a SUCCESS result with multiple hits, and in my log I see entries like 187.192.89.147 - - [13/Apr/2014:11:36:03 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 301 585 "-" "-" 187.192.89.147 - - [13/Apr/2014:11:36:03 +0100] "GET /phpMyAdmin/scripts/setup.php HTTP/1.1" 301 593 "-" "-" Secondly I know email is configured correctly, as each time I service fail2ban restart I get an email for each of the filters stopping/starting. However despite all this no action seems to be taken when one of these requests comes in. No email with whois, and no entries in iptables. What possibly could be preventing fail2ban from taking action? (everything looks in order in fail2ban-client -d and I can see the chains have loaded with iptables -L)

    Read the article

  • Configure IIS site to work with host header & hosts file entry

    - by HarveySaayman
    I'm I bit of an IIS / Web noob (I'm a C# backend service / winforms dev) so please bare with me :-) I've set up a site in IIS on my local dev machine. In the bindings section of the site ive added 4 bindings, all 4 for http: Host Name Port IP Address blog.sourcecube.co.za 26581 * www.blog.sourcecube.co.za 26581 * blog.sourcecube.co.za 26581 127.0.0.1 www.blog.sourcecube.co.za 26581 127.0.0.1 in my hosts file (drivers\etc\hosts), i've added the folling entries: 127.0.0.1 blog.sourcecube.co.za 127.0.0.1 www.blog.sourcecube.co.za when i ping my domain name from the command line it does in fact resolve to the loopback address, 127.0.0.1. So what I'm expecting to happen when i navigate to blog.sourcecube.co.za in my browser is for it to resolve to 127.0.0.1, and when the request hits IIS, it should know which site to serve because of the host header? But when i navigate to blog.sourcecube.co.za, i get an "Unable to connect, Firefox can't establish a connection to the server at blog.sourcecube.co.za" error. What am I doing wrong? --- UPDATE --- Navigating to blog.sourcecube.co.za:26581 from my browser works... I'd like get it working without specifying the port number though.

    Read the article

  • Unable to record using Jmeter

    - by krish
    Hi, I am trying to record a http web page using Jmeter 2.3.3 version.I has setup the JMeter proxy and tried, but did n't work. I have followed the below steps. Launch jmeter 2.3.3, added thred group to test plan Under Workbench-add-non-test elements- added HTTP proxy server. proxy server setting are port:9090, target:use recording controller, grouping:donot group samplers, Type:HTTp request and checked the boxes of all under http sampler settings Saved the settings Now in browser(IE 7.0 or firefox 3.0.16), under connection settings, setup the manual proxy settings as local host and port as 9090(no auto detect settings nothing, only manual proxy). Setting saved Now in the jmeter, started the http proxy server. Open a browser and hit the webpage needs to be tested. The page is not opened. In fact because of the changes made in browsers, no pages are opened. Whenever i try hitting a page, the pages are recorded in the Jmeter. but without the page open, how can i test. I looking for an immediate answer and my work is blocked. Immediate answer would be appreciated.

    Read the article

  • SSL connection hangs as client hello (curl, openssl client, apt-get, wget, everything)

    - by Niklas B
    Hi, I've run into a problem on my Debian VPS (a xen domU) regarding SSL. Namely almost all SSL connections hangs at client hello. For example: # curl -vI https://graph.facebook.com About to connect() to graph.facebook.com port 443 (#0) Trying 66.220.146.48... connected Connected to graph.facebook.com (66.220.146.48) port 443 (#0) successfully set certificate verify locations: CAfile: none CApath: /etc/ssl/certs SSLv3, TLS handshake, Client hello (1): It's the same when using the openssl client. However, some of the SSL traffic works (for example https://www.nordea.se). Server #uname -a Linux server.com 2.6.26-1-xen-amd64 #1 SMP Fri Mar 13 21:39:38 UTC 2009 x86_64 GNU/Linux It does however work on my Dom 0 (the main xen host). Apt-get I can't even run apt-get update with the debian security sources (hangs on reading headers) Open SSL At the begining I thought I had an old openssl client (0.9.8o-4) since I appeared to have a newer on the Dom 0 (0.9.8g-15+lenny8) but doing a manuanl update on the openssl deb didn't help. Open SSL Client This is the full output of when the openssl client hangs: http://pastebin.com/PAjwMap9 Closing thoughts I've Googled the crap out of this, and I'm not getting any further. I've seen problems with curl, apt-get etc. but they are all specific relating to the very application - not general for the system. Any thoughts?

    Read the article

  • Single m0n0wall - Two LAN Subnets - How To Setup

    - by SnAzBaZ
    I have two LAN subnets that I need to link together they are 192.168.4.0/24 and 192.168.5.0/24 There is a m0n0wall running on 192.168.4.1. It's LAN connection goes out to our network switch, and it's WAN port goes out to our ADSL modem. WAN is connected via PPPoE. The 192.168.4.0 subnet contains all of our office workstations. The 192.168.5.0 subnet contains development servers and test machines that need to obtain internet access and be "managed" by computers on the 192.168.4.0 subnet, but need to be on their own subnet as well. I have a Draytek 2820N configured on 192.168.5.1 with it's WAN2 port configured as 192.168.4.25 and a default gateway of 192.168.4.1. Machines on the 5.0 subnet can connect to the internet via the m0n0wall just fine. I configured a static route on the m0n0wall LAN interface, Network 192.168.5.0/24 and Gateway 192.168.4.25. Machines on the 5.0 subnet can ping machines on the 4.0 network but the reverse does not work. I configured a new firewall rule on the m0n0wall that allows any traffic on the LAN interface with a source IP of 192.168.4.25 to be allowed. The DrayTek firewall is currently configured to pass all traffic regardless. When I try to ping a machine in the 5.0 subnet from 4.0 I see this in my m0n0wall log: BLOCK 14:45:27.888157 LAN 192.168.4.25 192.168.4.37, type echoreply/0 ICMP So the reply is being sent from the 5.0 subnet but is not being allowed to reach my workstation because the firewall is blocking it. Why is the firewall blocking it ? I hope the explanation of my network is clear, please ask if you require further clarification. Thank you.

    Read the article

  • Enabled Network Discovery on Server, and now VNC and Squeezebox clients don't work

    - by Mike Hanson
    I've recently setup a Windows Server 2008. It's running an email server, Squeezebox server, MS SQL Server, etc. I'm doing remote maintenance with UltraVNC. I had everything working fine. Then the server needed to access a network share on another machine, and I was prompted to turn on network discovery, which I did. I chose the Home rather than Public option. Since doing that, some things have stopped working, while others are still fine. Shared folders and the the Email services (ports 25 and 110) are still accessible. VNC (port 5900) and Squeezeboxes (port 9000) no longer work. Here's what I've tried to try to solve the problem: Checked the network discovery settings, to see if anything looked strange. Checked the firewall settings, and those ports appear to be open. Also in the firewall settings, the entries for Private domain Network Discovery were all on, but the Domain/Public ones were off. I tried turning those on. In the services, turned on Function Discovery Resource Publication and SSDP Discovery. Any other suggestions?

    Read the article

  • OpenVPN Keeps Crashing

    - by Frank Thornton
    Oct 20 21:00:44 sb1 openvpn[2082]: <MY_IP>:28523 [vpntest] Peer Connection Initiated with [AF_INET]<MY_IP>:28523 Oct 20 21:00:44 sb1 openvpn[2082]: vpntest/<MY_IP>:28523 MULTI_sva: pool returned IPv4=10.8.0.6, IPv6=(Not enabled) Oct 20 21:00:44 sb1 openvpn[2082]: <MY_IP>:28522 WARNING: 'link-mtu' is used inconsistently, local='link-mtu 1576', remote='link-mtu 1376' Oct 20 21:00:44 sb1 openvpn[2082]: <MY_IP>:28522 WARNING: 'tun-mtu' is used inconsistently, local='tun-mtu 1532', remote='tun-mtu 1332' Oct 20 21:00:45 sb1 openvpn[2082]: <MY_IP>:28522 [vpntest2] Peer Connection Initiated with [AF_INET]<MY_IP>:28522 Oct 20 21:00:45 sb1 openvpn[2082]: vpntest2/<MY_IP>:28522 MULTI_sva: pool returned IPv4=10.8.0.10, IPv6=(Not enabled) Oct 20 21:00:46 sb1 openvpn[2082]: vpntest/<MY_IP>:28523 send_push_reply(): safe_cap=940 Client File: client dev tun proto tcp remote <IP> 443 resolv-retry infinite nobind tun-mtu 1500 tun-mtu-extra 32 mssfix 1410 persist-key persist-tun auth-user-pass comp-lzo SERVER: port 443 #- port proto tcp #- protocol dev tun tun-mtu 1500 tun-mtu-extra 32 reneg-sec 0 #mtu-disc yes mssfix 1410 ca /etc/openvpn/easy-rsa/2.0/keys/ca.crt cert /etc/openvpn/easy-rsa/2.0/keys/server.crt key /etc/openvpn/easy-rsa/2.0/keys/server.key dh /etc/openvpn/easy-rsa/2.0/keys/dh1024.pem plugin /etc/openvpn/openvpn-auth-pam.so /etc/pam.d/login #plugin /usr/share/openvpn/plugin/lib/openvpn-auth-pam.so /etc/pam.d/login #- Comment this line if you are using FreeRADIUS #plugin /etc/openvpn/radiusplugin.so /etc/openvpn/radiusplugin.cnf #- Uncomment this line if you are using FreeRADIUS client-to-client client-cert-not-required username-as-common-name server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" keepalive 3 30 comp-lzo persist-key persist-tun What is causing the VPN to keep dropping the connection and then reconnecting?

    Read the article

  • Configure Domino to use SMTP routing and hMailServer

    - by Sébastien Lachance
    I have been trying for a couple of days to set up a Domino 8.5 server. Basically, I want everything to be run inside a local network. Right now I can send email to other user in the Domino directory without any mail address. I am pretty new to all this stuff, so maybe the answer will be really obvious. What I need to do is be able to send a mail from somewhere else to a domino user that will be redirected to his account. On the Domino server, I also have hMailServer installed on port 25. I configured Domino to use port 26. I followed those step to get where I am now. -I have set the Fully qualified Internet host name to "preview.notes". -Smtp Listener task changed to Enabled to turn on the Listener so that the server can receive messages routed via SMTP routing -Setting up SMTP routing within the local Internet domain (http://www.h2l.com/help/help85%5Fadmin.nsf/f4b82fbb75e942a6852566ac0037f284/7f9738a49efc4f58852574d500097b01?OpenDocument) -I modified the person to use the [email protected] address. -I'm using the hMailServer (which have the local "preview.local" domain name) to send mail to [email protected]. When sending mail I got an error telling that the DNS is not set up correctly. Is using the Domino Smtp server instead of hMailServer will solve the problem? I can Telnet the Domino Smtp Server.

    Read the article

  • Time-Machine backup over SSH tunnel to NFS mount

    - by BTZ
    I've recently started using a new NAS which runs CentOS 6.2. One of the purposes of the NAS would be to serve as a backup target. Whilst I have been using Apple's Time-Machine for a while and I am very satisfied with it, I'd like to continue using it. Backing up directly to an address in my network is no hassle; all works fine. For security reasons I'd like all my traffic to go through an ssh tunnel to the NAS. This way I can avoid needing to get a VPNserver (for personal reasons). As of NFSv4 the NFS deamon is bound to port 2049, which makes it easy for me to direct all traffic through a ssh tunnel. Tunnel: ssh -f admin@ms -L 2000:localhost:2049 -N Mount: mount -t nfs -o nfsvers=4,rw,proto=tcp,sync,intr,hard,timeo=600,retrans=10,wsize=32768,rsize=32768,port=2000 localhost:/mac_backup /Volumes/backup This works fine for Finder/terminal and throughput is almost equal to direct traffic. (CPU of the NAS does ride high when I reach max bandwidth though) Now the problem: With Time-Machine I can't use the NFS mount point mounted on localhost. TM seems to try to connect to it and then give me a "OSStatus error 65". I also tried using NFSv3 (I correctly forwarded all ports) with no luck. Can anyone shed a light on this and/or give a solution?

    Read the article

  • What could cause an 101 Error in WAMP under Windows 7 ?

    - by Brayn
    Hey, I'be been using WAMP for local development for quite a while now but lately I've been getting an Error 101 message when I browse localhost sites. It's possible for this to have appeared after the last WAMP update but I'm not 100% sure on this. If I try again and again, after several page refreshes it works but it's really annoying! The exact error message is: Error 101 (net::ERR_CONNECTION_RESET): Unknown error. This is my configuration: OS: Windows 7 Apache: 2.2.11 PHP: 5.2.9-2 WAMP: 2.0 Also the local scripts connect to a remote MySQL server, they don't use the local MySQL(I don't know if it matters, just though I let you know). I've been looking into the apache logs and I've found the following. It seems that the apache server keeps restarting and I can't figure why: [Wed Oct 14 13:52:30 2009] [notice] Parent: child process exited with status 255 -- Restarting. [Wed Oct 14 13:52:30 2009] [notice] Apache/2.2.11 (Win32) PHP/5.2.9-2 configured -- resuming normal operations [Wed Oct 14 13:52:30 2009] [notice] Server built: Dec 10 2008 00:10:06 [Wed Oct 14 13:52:30 2009] [notice] Parent: Created child process 6784 [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Child process is running [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Acquired the start mutex. [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Starting 64 worker threads. [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Starting thread to listen on port 80. [Wed Oct 14 13:52:32 2009] [notice] Parent: child process exited with status 255 -- Restarting. [Wed Oct 14 13:52:33 2009] [notice] Apache/2.2.11 (Win32) PHP/5.2.9-2 configured -- resuming normal operations [Wed Oct 14 13:52:33 2009] [notice] Server built: Dec 10 2008 00:10:06 [Wed Oct 14 13:52:33 2009] [notice] Parent: Created child process 3572 [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Child process is running [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Acquired the start mutex. [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Starting 64 worker threads. [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Starting thread to listen on port 80. Also I've checked Windows Firewall and disabled any other protection that I have on this computer with no improvement. Thanks!

    Read the article

  • Torrent upload ratio not updated on Synology DS212+

    - by user179271
    I have a Synology DS212+ NAS running DSM 4.2-3211 (current version). I use it for several purposes including torrent download using Download Station and a tracker that needs authentication. My problem is that my download/upload ratio isn't updated, so it constantly falls down. My NAS is behind a router, and I configured the NAT to forward ports 6890 to 6999 to the internal IP address of the NAS. Here are the Download Station settings : TCP port : 6990, Sharing ratio : 900%, Sharing time : infinite, max download speed : 0 (no limit), max upload speed : 0 (no limit), BT protocol encryption : checked, max numbers of peers allowed by torrent file : 4000, DHT : checked, with port 6889. When the DHT option is not checked, the NAS doesn't upload any files. I don't know what is this option for. Can someone help me to solve this problem ? Did I miss any step, or does it come from the NAT ? How is the authentication managed by Dowload Station ? (Sorry for my english) Thanks.

    Read the article

  • Understanding tcptraceroute versus http response

    - by kojiro
    I'm debugging a web server that has a very high wait time before responding. The server itself is quite fast and has no load, so I strongly suspect a network problem. Basically, I make a web request: wget -O/dev/null http://hostname/ --2013-10-18 11:03:08-- http://hostname/ Resolving hostname... 10.9.211.129 Connecting to hostname|10.9.211.129|:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: ‘/dev/null’ 2013-10-18 11:04:11 (88.0 KB/s) - ‘/dev/null’ saved [13641] So you see it took about a minute to give me the page, but it does give it to me with a 200 response. So I try a tcptraceroute to see what's up: $ sudo tcptraceroute hostname 80 Password: Selected device en2, address 192.168.113.74, port 54699 for outgoing packets Tracing the path to hostname (10.9.211.129) on TCP port 80 (http), 30 hops max 1 192.168.113.1 0.842 ms 2.216 ms 2.130 ms 2 10.141.12.77 0.707 ms 0.767 ms 0.738 ms 3 10.141.12.33 1.227 ms 1.012 ms 1.120 ms 4 10.141.3.107 0.372 ms 0.305 ms 0.368 ms 5 12.112.4.41 6.688 ms 6.514 ms 6.467 ms 6 cr84.phlpa.ip.att.net (12.122.107.214) 19.892 ms 18.814 ms 15.804 ms 7 cr2.phlpa.ip.att.net (12.122.107.117) 17.554 ms 15.693 ms 16.122 ms 8 cr1.wswdc.ip.att.net (12.122.4.54) 15.838 ms 15.353 ms 15.511 ms 9 cr83.wswdc.ip.att.net (12.123.10.110) 17.451 ms 15.183 ms 16.198 ms 10 12.84.5.93 9.982 ms 9.817 ms 9.784 ms 11 12.84.5.94 14.587 ms 14.301 ms 14.238 ms 12 10.141.3.209 13.870 ms 13.845 ms 13.696 ms 13 * * * … 30 * * * I tried it again with 100 hops, just to be sure – the packets never get there. So how is it that the server does respond to requests via http, even after a minute? Shouldn't all requests just die? I'm not sure how to proceed debugging why this server is slow (as opposed to why it responds at all).

    Read the article

  • How to set up simple VPN for secure Internet connections over unencrypted Wi-Fi on Windows?

    - by Senseful
    I'm looking for a solution similar to the one in this question, except that I don't have a linux computer. I have windows computers that could be set up to accept VPN connections. Preferably I want to set this up on either Windows Server 2003 or Windows XP. I'd like to connect different devices (e.g. iPhone, iPad, laptops, etc.) that are on open unsecure wireless networks (e.g. the one's you see at places like Starbucks) to this VPN to ensure that all my data is secure. I found an article that shows that you can enable VPN connections on Windows XP. After following those steps, though, I'm not sure what to do. Which ports do I open on my firewall? Which VPN settings do I use on my devices such as the iPhone? Do I use L2TP, PPTP, or IPSec? What's the difference between these? Are there any other steps missing in that tutorial? I'm hoping that since Windows has this built in feature, that it will be much simpler to set up rather than having to deal with setting up something such as OpenVPN. If I follow those settings and enable port forwarding on port 1723, and then use the following settings on the iPhone: PPTP (IP Address) RSA SecurID: Off Encryption Level: Auto Send All Traffic: On Proxy: Off It shows "Connecting..." then "Disconnecting..." and the following error message: VPN Configuration A connection could not be established to the PPP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I'm using a user account that I enabled privileges to in the VPN settings on the Windows machine.

    Read the article

  • Why Wireshark does not recognize this HTTP response?

    - by Alois Mahdal
    I have a trivial CGI script that outputs simple text content. It's written in Perl and using CGI module and it specifies only the most basic headers: print $q->header( -type => 'text/plain', -Content_length => $length, ); print $stuff; There's no apparent issue with functionality, but I'm confused about the fact that Wireshark does not recognize the HTTP response as HTTP--it's marked as TCP. Here is request and response: GET /cgi-bin/memfile/memfile.pl?mbytes=1 HTTP/1.1 Host: 10.6.130.38 User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:11.0) Gecko/20100101 Firefox/11.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: cs,en-us;q=0.7,en;q=0.3 Accept-Encoding: gzip, deflate Connection: keep-alive HTTP/1.1 200 OK Date: Thu, 05 Apr 2012 18:52:23 GMT Server: Apache/2.2.15 (Win32) mod_ssl/2.2.15 OpenSSL/0.9.8m Content-length: 1048616 Keep-Alive: timeout=5, max=100 Connection: Keep-Alive Content-Type: text/plain; charset=ISO-8859-1 XXXXXXXX... And here is the packet overview (Full packet is here on pastebin) No. Time Source srcp Destination dstp Protocol Info tcp.stream abstime 5 0.112749 10.6.130.38 80 10.6.130.53 48072 TCP [TCP segment of a reassembled PDU] 0 20:52:23.228063 Frame 5: 1514 bytes on wire (12112 bits), 1514 bytes captured (12112 bits) Ethernet II, Src: Dell_97:29:ac (00:1e:4f:97:29:ac), Dst: Dell_3b:fe:70 (00:24:e8:3b:fe:70) Internet Protocol Version 4, Src: 10.6.130.38 (10.6.130.38), Dst: 10.6.130.53 (10.6.130.53) Transmission Control Protocol, Src Port: http (80), Dst Port: 48072 (48072), Seq: 1, Ack: 330, Len: 1460 Now when I see this in Wireshark: there's usual TCP handshake then the GET request shown as HTTP with preview then the next packet contains the response, but is not marked as an HTTP response--just a generic "[TCP segment of a reassembled PDU]", and is not caught by "http.response" filter. Can somebody explain why Wireshark does not recognize it? Is there something wrong with the response?

    Read the article

  • Node js server not responding outside localhost centos

    - by David Martinez
    I'm running a basic express server from CentOS but for some reason it is not responding outside of localhost, I have tried everything I have found on google but nothing works so far. This is my express server: app.listen(3000,"0.0.0.0"); If I do curl http://localhost:3000/ in the server it works fine. If I curl to the ip of the server it doesn't work. I already changed my iptables num target prot opt source destination 1 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 2 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 3 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:3000 There is currently a apache server running on port 80 with no problems. I also tried setting a VirtualHost on apache but it didn't work either: <VirtualHost *:80> ServerName SubDOmain.MyDomain.com ProxyRequests off <Proxy *> Order allow,deny Allow from all </Proxy> ProxyPass / http://localhost:3000/ ProxyPassReverse / http://localhost:3000/ ProxyPreserveHost on </VirtualHost> There is another virtual host working fine that redirects to another DocumentRoot. I'm running Node on root for testing purpose, but the node application owner is another user. All folders have 705 and files 664 Edit: I stopped apache and run my node app on port 80 and it working fine, I could access node app from my ip and domain.

    Read the article

  • CLOSE_WAIT sockets burst - perhaps because of iptables settings?

    - by Fabrizio Giudici
    I have an Ubuntu 12.04 server virtual box where basically the installed software and configuration are the default ones, plus the installation of a jetty 6 server which servers a few websites. To keep things simple I didn't install apache httpd and used iptables for exposing jetty (which runs on the 8080 port) to the port 80. These are the results of /sbin/iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain POSTROUTING (policy ACCEPT) target prot opt source destination I must confess I have a shallow comprehension of how iptables works, in particular for the different kind of chains. This thing works, but sometimes I have an explosion of sockets that stay permanently in CLOSE_WAIT state. I know about what this state means, but since I didn't write the code that manages servlets (they are handled by jetty) I can't fix the problem by patching my code. Eventually the amount of CLOSE_WAIT sockets builds up and makes the server not responsive, so I have to restart jetty. I've looked around for similar problems wth CLOSE_WAIT, and only found cases related to the programmer's code, or problems with Tomcat, not Jetty. I was wondering whether they could be related to a partially broken iptables configuration (the alternative is a bug in Jetty 6, but I first want to exclude other possible causes). Thanks.

    Read the article

  • How to get Synergy working on Ubuntu 11.10 and Windows 7?

    - by Linda
    I'm using Ubuntu 11.10 32-bit and Windows 7 64-bit, however, Synergy only works when a window (application or folder) is open and touching the edge of the screen where the mouse should "jump". In other words, if a window is open and maximized, Synergy works normally. Without any windows, the mouse does not jump to the other screen. My steps: (Ubuntu) apt-get install -y quicksynergy (Windows) Install Synergy (I've tried both 1.3.8 and 1.4.8 and both 32 and 64-bit) On Ubuntu 11.10 32-bit (Synergy Server config): ~/.quicksynergy/synergy.conf section: screens myubuntu: mywin7: end section: links myubuntu: right = mywin7 mywin7: left = myubuntu end On Ubuntu 11.10 32-bit: $ /usr/bin/synergys -f --config .quicksynergy/synergy.conf ... 2012-04-25T14:04:12 NOTE: client "mywin7" has connected /build/buildd/synergy-1.3.6/lib/server/CServer.cpp,287 (output hangs here) On Windows 7 64-bit: Synergy 1.3.8 Client on Microsoft Windows 7 x86 (WOW64) started client connecting to 'myubuntu': ###.###.###.###:24800 connected to server (output hangs here) At this point, things should work, but my mouse still can't change screens unless a window is maximized on my Ubuntu machine. Everything is running on port 24800. No firewall on Ubuntu. Firewall port 24800 open on Windows 7. This was previously working on Ubuntu 10.10 and Windows 7 (so only Ubuntu has been upgraded). I'm open to using either 32 or 64-bit on either server or client side, but I just want to get it working on Ubuntu 11.10 and Windows 7! I'm also using Ubuntu Classic (no effects), and not Unity.

    Read the article

  • Oracle Error ORA-12560 TNS:Protocol Adapter error?

    - by David Basarab
    I am using Oracle Database 10g. Both Servers are Windows 2003. I have an Orcale Database set up on one server. Here is the TNSNames.ora from the server with the database. # tnsnames.ora Network Configuration File: C:\oracle\product\10.2.0\db_1\network\admin\tnsnames.ora # Generated by Oracle configuration tools. ORCL.VIRTUALHOLD.COM = (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = databaseServer)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = orcl) ) ) The Environmental Variables on the Server are ORACLE_HOME = C:\oracle\product\10.2.0\db_1 ORACLE_SID = orcl I am trying to connect to it from another box that has Oracle Client installed. Here is the tnsnames.ora installed on the other client server. # tnsnames.ora Network Configuration File: C:\oracle\product\10.2.0\client_1\network\admin\tnsnames.ora # Generated by Oracle configuration tools. ORCL = (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = databaseServer)(PORT = 1521)) ) (CONNECT_DATA = (SERVICE_NAME = orcl) ) ) ORACLE_HOME = C:\oracle\product\10.2.0\client_1 ORACLE_SID = orcl Locally on the database server I can connect to through sqlplus with no issues. On the client machine I keep getting the error: ORA-12560: TNS:protocol adapter error What am I missing? Does the client TNSNames.ora need to be different?

    Read the article

  • Isolating a computer in the network

    - by Karma Soone
    I've got a small network and want to isolate one of the computers from the whole network. My Network: <----> Trusted PC 1 ADSL Router --> Netgear dg834g <----> Trusted PC 2 <----> Untrusted PC I want to isolate this untrusted PC in the network. That means the network should be secure against : * ARP Poisoning * Sniffing * Untrusted PC should not see / reach any other computers within the network but can go out the internet. Static DHCP and switch usage solves the problem of sniffing/ARP poisoning. I can enable IPSec between computers but the real problem is sniffing the traffic between the router and one of the trusted computers. Against getting a new IP address (second IP address from the same computer) I need a firewall with port security (I think) or I don't think my ADSL router supports that. To summarise I'm looking for a hardware firewall/router which can isolate one port from the rest of the network. Could you recommend such a hardware or can I easily accomplish that with my current network?

    Read the article

  • VLAN Through Switch Doesn't Work

    - by vcsjones
    I have the following scenario: I have a Cisco Aironet 1040 access point. I have it configured with two SSIDs, each going to a different VLAN. So: SSID internal : VLAN 90 SSID guest : VLAN 70 On the router side, I have a Cisco RV220W (with the radios now turned off) and have setup VLANs with like VLAN IDs. VLAN 90 : 192.168.90.0/24 VLAN 70 : 192.168.70.0/24 As far as DHCP is concerned, each VLAN has a "DHCP Server" in the router's configuration: So with the access point connected directly to the router, everything works great. I connect to the internal network, and I get a 192.168.90.x address, and the guest network gets a 70.xxx address. Next I introduced a Cisco SG200-50 PoE switch between the router and the access point. The port is configured as a trunk port, so the VLAN tags should go right through the switch back to the router. However, when something is connected to the access point, nothing works. It isn't able to get an IP address, and manually assigning one doesn't seem to let any traffic route. Given that the access point works correctly when connected to the router directly, I believe the switch is misconfigured. What am I missing here? What can I use to better diagnose what the problem might be? It's small business equipment, so CLI access is not available. Below are screenshots of the switch's config. The access point is connected to GE2.

    Read the article

  • Wake on LAN Problem

    - by Caley Woods
    I'm working to get wake on lan (wol) working so that we can do some power management at my workplace. I've enabled WOL on a test laptop running Win 7 x64 and put it to sleep and hibernate both with no luck. I'm using a 3rd party utility and I've ran wireshark on the test laptop with it booted up and I can see the WOL packets coming in and the machine refuses to wake from sleep or hibernate. I thought maybe it was the computer I was using so I had another Win 7 x64 laptop nearby and I tried it, same scenario. We're in a cisco environment and I believe I gotten all the pieces in place since I'm seeing the WOL packets come through. I've tested two machines on the same subnet to eliminate the possibility of a misconfiguration on the switch, this also has the same behavior. The laptop models are a Compaq 6510b and 6730b. Is there something I'm missing? I'm trying this across UDP port 50200 since that's the port the actual management system will use after I get it working.

    Read the article

  • VLAN Tagging Traffic on Cisco Switch

    - by David W
    I have a situation where I'm setting up multiple VLANS on a pfSense firewall on the same physical interface for a client. So in pfSense, I now have VLAN 100 (employees) and VLAN 200 (students - student computer lab). Downstream from pfSense, I have a Cisco SG200 switch, and coming off of the SG200 is the student lab (running on a Catalyst 2950. Yes, that's old, but it works, and this is a poor nonprofit we're talking about). What I'd like to do is tag everything on the network as VLAN 100, except for the student computer lab. Earlier today when I was on-site with the client, I went into to the old Catalyst 2950, and assigned all of its ports to access VLAN 200 (switchport mode access vlan 200) without setting up a trunk on the Catalyst or on the SG200. Looking back on it, I now understand why internet in the lab broke. I reverted the lab back to the default VLAN1 (we're still running on a different firewall - we haven't deployed pfSense -, and the traffic is still separated physically). So my question is, what do I need to do in order to properly deploy this scenario? I believe the correct answer is: Ensure VLANs 100 and 200 are setup in pfSense, and that DHCP is operating correctly (on separate subnets) Setup a trunkport VLAN that allows both 100 & 200 traffic, and plug that port directly into pfSense. Setup a VLAN 200 trunkport on the SG200 (It's not running iOS, but if it were, the command would be switchport trunk native vlan 200), which will then plug into the Catalyst 2950. Setup a VLAN 200 trunkport on the Catalyst 2950 (that is plugged into the SG200 VLAN200 port with the same command - switchport trunk native vlan 200) Setup the rest of the ports on the old Catalyst 2950 in the lab to be access ports on VLAN200. Is there anything that I'm missing, or do I need to tweak any of these steps, in order to properly segment the network traffic?

    Read the article

  • What to look for in a switch with LAN/WAN verses an iSCSI SAN?

    - by Luke
    I'm setting up a VMWare ESXi 5 environment with 3 server nodes. Dell recommended 2x Force10 S60 switches shared (iSCSI SAN, LAN/WAN). The S60 switches are extremely powerful. They have 1.25 GB of buffer cache, < 9us latency. But they are very expensive (online price ~$15k per switch, actual quote a little less). I've been told that "by the book" you should at least have 2 internal switches for SAN, and 2 switches for LAN/WAN (each with a redundant). I know some of the pros and cons of each approach. What I'm wondering is, would it be more cost effective to disjoin the SAN from LAN with less expensive switches? The answer to this question highlights what I should be looking for in a switch for the SAN. What should I be looking for in a LAN/WAN switch, in comparison to the SAN? With the above linked question for the SAN: How is buffer latency measured? When you see 36 MB of buffer cache, is that shared or per port? So 36 MB would be 768kb or 36MB per port? With 3 to 6 servers how much buffer cache do you really need? What else should I be looking at? Our application will be heavily using HTML5 websockets (high number of persistent connections). The amount of data being sent is small; Data sent between client <- server isn't broadcasted (not a chat/IM service). We will be doing some database reporting too (csv export, sums, some joins). We are a small business and on a budget. We'd probably only be able to spend no more than $20k on switches total (2 or 4).

    Read the article

< Previous Page | 187 188 189 190 191 192 193 194 195 196 197 198  | Next Page >