Search Results

Search found 19125 results on 765 pages for 'hard disk'.

Page 196/765 | < Previous Page | 192 193 194 195 196 197 198 199 200 201 202 203  | Next Page >

• Bluetooth firmware problem in Ubuntu 13.04

  - by chanzerre

  I have a [Dell Inspiron][1] 15R 5520 laptop. Bluetooth is not working at all. rfkill list all gives 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no dmesg|grep -i bluetooth gives [ 13.644428] Bluetooth: Core ver 2.16 [ 13.644445] Bluetooth: HCI device and connection manager initialized [ 13.644453] Bluetooth: HCI socket layer initialized [ 13.644455] Bluetooth: L2CAP socket layer initialized [ 13.644461] Bluetooth: SCO socket layer initialized [ 15.861363] Bluetooth: hci0 command 0x1003 tx timeout [ 15.903443] Bluetooth: can't load firmware, may not work correctly [ 17.332535] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 17.332538] Bluetooth: BNEP filters: protocol multicast [ 17.332544] Bluetooth: BNEP socket layer initialized [ 17.393768] Bluetooth: RFCOMM TTY layer initialized [ 17.393781] Bluetooth: RFCOMM socket layer initialized [ 17.393783] Bluetooth: RFCOMM ver 1.11 hciconfig gives hci0: Type: BR/EDR Bus: USB BD Address: E0:06:E6:D5:DB:46 ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING PSCAN ISCAN RX bytes:687 acl:0 sco:0 events:56 errors:0 TX bytes:2024 acl:0 sco:0 commands:52 errors:0 I have visited the site http://wireless.kernel.org/en/users/Drivers/b43 and according to it lspci -vnn -d 14e4: gives 08:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01) Subsystem: Dell Wireless 1704 802.11n + BT 4.0 [1028:0016] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at c1500000 (64-bit, non-prefetchable) [size=32K] Capabilities: <access denied> Kernel driver in use: wl So I got my PCI-ID as 14e4:4365 which it says is not supported. The alternative is wl. What should I do? My Wi-Fi is working normally without any problems, but Bluetooth is not working. sudo dpkg -i wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb gives following error (Reading database ... 208543 files and directories currently installed.) Unpacking wireless-bcm43142-dkms (from wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb) ... Setting up wireless-bcm43142-dkms (6.20.55.19-1) ... Loading new wireless-bcm43142-6.20.55.19 DKMS files... Building only for 3.8.0-23-generic Building initial module for 3.8.0-23-generic Traceback (most recent call last): File "/usr/share/apport/package-hooks/dkms_packages.py", line 22, in <module> import apport ImportError: No module named apport Error! Bad return status for module build on kernel: 3.8.0-23-generic (x86_64) Consult /var/lib/dkms/wireless-bcm43142/6.20.55.19/build/make.log for more information.

  Read the article

• GPT Not mounting using "normal" GPT mounting techniques 12.04

  - by Roy Markham

  I've got two 2TB drivess: one MBR and the other GPT. sudo blckid /dev/sdb1 returns a blank. gdisk shows: Partition table scan: MBR: protective BSD: not present APM: not present GPT: present Found valid GPT with protective MBR; using GPT. Warning! Secondary partition table overlaps the last partition by 1970 blocks! You will need to delete this partition or resize it in another utility. Disk /dev/sdb: 3907027055 sectors, 1.8 TiB Logical sector size: 512 bytes Disk identifier (GUID): 38A1113D-B5E9-4B69-ABFF-ACB27AFB3DDD Partition table holds up to 128 entries First usable sector is 34, last usable sector is 3907027021 Partitions will be aligned on 8-sector boundaries Total free space is 2014 sectors (1007.0 KiB) Number Start (sector) End (sector) Size Code Name 1 34 262177 128.0 MiB 0C01 Microsoft reserved part 2 264192 3907028991 1.8 TiB 0700 Basic data partition mounting via fstab or -t gives same error when using NTFS or NTFS-3g "NTFS signature is missing" GParted says one partition is overwriting another, yet windows shows no errors at all. The drive is also mounted easily via MacOs (triple boot)

  Read the article

• How do I get wireless to work on a Dell Mini 1018 with Realtek RTL 8188CE Network Adapter?

  - by Laurence Nagel

  My Dell Mini 1018 used to work fine with Ubuntu 12.04 with no problems connecting with the wireless card. Then I made the big mistake of attempting to disable WiFi by right-clicking on the wireless applet and un-checking "Enable Wireless." Since then, I cannot get wireless working again. The wireless applet reports that "wireless is disabled by hardware switch" but there is no hardware switch on this computer. Issuing a rfkill list yields the following: 0: dell-wifi: Wireless LAN Soft blocked: yes Hard block: yes 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I'm in way over my head, and my computer is now useless. Help!!!

  Read the article

• I can't figure out how to run ubuntu .iso from thumbdrive?

  - by Judge Cole Stanley

  I downloaded Ubuntu 12.04.1 and I can't find a solid way to run it from the disk version of Ubuntu 11.04 for a clean install. I think the hard drive is messed up, or else I would install 11.04, but it won't work. So I wanna install 12.04.1 from a thumbdrive, so I can actually use this computer without using the demo and installing everything when it dies, or shuts off... Please help? I want to make it at least bootable from a thumbdrive, just so I can lightly browse the internet and what not... it doesn't have to be a hard install.

  Read the article

• Autodetect/mount SDCards and run script for them on Linux

  - by Brendan

  Hey Everyone, I'm currently running SME Server, and need to have a script run upon the attachment of SD Cards to my server. The script itself works fine (it copies the contents of the cards), but the automounting and execution of the script is where I'm having issues. The I have a USB hub consisting of 10 USB ports; that shows up as: [root@server ~]# lsusb Bus 004 Device 002: ID 0000:0000 Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 001 Device 055: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 051: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 050: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 001: ID 0000:0000 (The hub is the TERMINUS TECHNOLOGY INC entries) As I cannot plug SD Cards directly into the server; I use a USB to SD card attachement (10 of them) plugged into the hub to read the cards. Upon pluggig the 10 attachments (without cards) into the hub; lsusb yields the following: [root@server ~]# lsusb Bus 004 Device 002: ID 0000:0000 Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 001 Device 073: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 072: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 071: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 070: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 069: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 068: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 067: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 066: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 065: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 064: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 055: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 051: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 050: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 001: ID 0000:0000 As you can see, the readers are the "Gensys Logic, Inc" entries. Plugging in an SD card to a reader doesn't affect lsusb (it reads exactly as above), however my system recognises the cards fine; as indicated by dmesg: Attached scsi generic sg11 at scsi54, channel 0, id 0, lun 0, type 0 USB Mass Storage device found at 73 SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through sdd: sdd1 SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through sdd: sdd1 SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through sdd: sdd1 If I manually mount sdd1 (mount /dev/sdd1 /somedirectory/) this works fine. What I'm really after is a solution that automounts each of the cards as they are inputted into the reader; and executes a script for them (this will involve copying their contents to another directory). My problem is that I don't know how to do this; I don't think udev will work as the USB devices don't change; if I could somehow get udev working with /dev/disk/by-path/ however I think this is doable (it seems to keep constant entries). ls /dev/disk returns: pci-0000:00:1d.7-usb-0:4.1.1.1:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.1.2:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.1.3:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.1.4:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.2:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.3:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.4:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.2:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.3:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.4:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.4:1.0-scsi-0:0:0:0-part1 pci-0000:0b:01.0-scsi-0:0:1:0 pci-0000:0b:01.0-scsi-0:0:1:0-part1 pci-0000:0b:01.0-scsi-0:0:1:0-part2 From above, we can see I have only one card plugged into the reader (pci-0000:00:1d.7-usb-0:4.4:1.0-scsi-0:0:0:0-part1). Going mount /dev/disk/by-path/pci-0000\:00\:1d.7-usb-0\:4.4\:1.0-scsi-0\:0\:0\:0-part1 Works and places the card under /media/usbdisk/, however: mount /dev/disk/by-path/pci-0000\:00\:1d.7-usb-0\:4.4\:1.0-scsi-0\:0\:0\:0-part1 slot1/ doesn't work, and returns "mount: can't get address for /dev/disk/by-path/pci-0000" Any ideas and solutions would be great, I've seen the knowledge of a lot of the guys on here before so I'm hopeful someone can help me out. Thanks

  Read the article

• How to fix 'grub error file not found' when installing 12.04?

  - by Tomasz Grabowski

  i'm trying to install Ubuntu. I don't know if it is important, but i'm trying to install it on external HDD. In the end i have external bootable HDD which only displays: error: file not found grub recovery> From the beginning: I've downloaded ubuntu-12.04-desktop-i386.iso I've used LiLi USB Creator (LinuxLive) to create bootable pendrive from that image I've bootet from it, it works I've clicked "Try ubuntu", it works too. I've used GParted to look over drivers (disks) My primary embedded disk is seen as /dev/sda My attached external disk as /dev/sdb My PenDrive as /dev/sdc I've created partitions on /dev/sdb Fist partition for system (over 200GiB) Second was there already (it's xsf, and i don't want to touch it :P) Third is extended partition, with 1 locital partiton (10GiB) for swap I've started installation i've choose "somethin else" in ... i belive secound screeb then is selected /dev/sdb as boot disk for first partiton of /dev/sdb i set i want ext3 file system, i've check "formattin" checkbox, and mount path set to "/" firs logical partiton set as swap partition After installation finished, i restarted my computer. When i boot from my primary disc it's work ok, my previous operating system - vista - works ok. When i set my BIOS to boot from my external disc, i only get that message: error: file not found grub recovery> I've try to reinstall it, but didn't help... In desperation, i've try to read a bit about that "grub recovery" command-line and experiment a bit... I'm not sure if this has had any point, or if it give you some information (notice, that i don't know what i'm doing :P ) when i've type command: insmod (hd1,1)/boot/grub/linux.mod i've get message: unknown filesystem the same with: insmod (hd1,msdos1)/boot/grub/linux.mod the same with: insmod ext3 but i get no message after command: insmod ext2 ... notice that i really don't know what this command exactly do, but than i thought that maybe if i reinstall ubuntu with ext2 filesystem, it will work. I've done that, but symptoms are the same. I've go back to that Live version of ubuntu, filesystem and basics directories seems to be present on /dev/sdb1 ... i'm completely unfamiliar with GRUB. I'm also don't know which wersion of GRUB it is, i hope there is only one version on ubuntu-12.04-desktop-i386.iso Any help? Thax

  Read the article

• Wireless Broadcom 4313 not working on Ubuntu 12.04

  - by user88568

  It seems a lot of people are having this problem, but none of the posted solutions have worked for me so far. My driver is installed and activated, I have tried removing and re-adding the network, and various other fixes. No networks were picked up on my first boot, the next day wireless worked fine, and since then it does not detect networks, and when I manually try to connect, it repeatedly asks for the password and does not connect. Here's my info: 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Dell Inspiron M5010 / XPS 8300 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f0500000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information: Len=78 Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 00-00-a1-ff-ff-f3-70-f1 Capabilities: [16c] Power Budgeting Kernel driver in use: wl Kernel modules: wl, bcma, brcmsmac root@michelle-laptop:/home/michelle# ifconfig eth0 Link encap:Ethernet HWaddr 70:f1:a1:f3:ba:ab inet6 addr: fe80::72f1:a1ff:fef3:baab/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:29 TX packets:0 errors:30 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 eth1 Link encap:Ethernet HWaddr f0:4d:a2:53:83:7a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:104 errors:0 dropped:0 overruns:0 frame:0 TX packets:104 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8000 (8.0 KB) TX bytes:8000 (8.0 KB) root@michelle-laptop:/home/michelle# lsmod Module Size Used by dm_crypt 22528 0 snd_hda_codec_hdmi 31775 1 snd_hda_codec_realtek 174313 1 snd_hda_intel 32765 5 snd_hda_codec 109562 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80845 4 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event parport_pc 32114 0 ppdev 12849 0 binfmt_misc 17292 1 lib80211_crypt_tkip 17275 0 bnep 17830 2 rfcomm 38139 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq joydev 17393 0 wl 2646601 0 snd 62064 19 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd btusb 17912 0 bluetooth 158438 11 bnep,rfcomm,btusb uvcvideo 67203 0 videodev 86588 1 uvcvideo snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lib80211 14040 2 lib80211_crypt_tkip,wl intel_ips 17822 0 psmouse 72919 0 serio_raw 13027 0 mei 36570 0 dell_laptop 17767 0 dell_wmi 12601 0 dcdbas 14098 1 dell_laptop sparse_keymap 13658 1 dell_wmi mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp usbhid 41906 0 hid 77367 1 usbhid wmi 18744 1 dell_wmi i915 414817 3 atl1c 36718 0 drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 root@michelle-laptop:/home/michelle# iwlist scan lo Interface doesn't support scanning. eth1 Interface doesn't support scanning. eth0 No scan results root@michelle-laptop:/home/michelle# rfkill list 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no Obviously I don't know what I'm doing. I'd appreciate any help! Thanks!

  Read the article

• Intel Centrino Wireless N 1000 doesn't work on a Lenovo Z560

  - by Timetraveler

  I upgraded my Ubuntu 11.04 to 11.10 and my Wifi has stopped working. I have a Lenovo Z560 that has Intel centrino wireless-N 1000. I have searched various threads having similar problems for a solution and have no success. The wlan0 is not even showing up in rfkill. Please help me find a solution. I am giving below the output of various debug commands. Thanks in advance. DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10" ----##uname -a Linux gurucharapathy-laptop 3.0.0-17-generic-pae #30-Ubuntu SMP Thu Mar 8 17:53:35 UTC 2012 i686 i686 i386 GNU/Linux ----##lspci -nnk | grep -iA2 net 05:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1000 [8086:0084] Subsystem: Intel Corporation Centrino Wireless-N 1000 BGN [8086:1315] Kernel modules: iwlagn 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) Subsystem: Lenovo Device [17aa:392e] Kernel driver in use: r8169 ----##iwconfig lo no wireless extensions. eth0 no wireless extensions. ----##iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. ----##rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no ----##lsmod Module Size Used by rfcomm 38408 8 bnep 17923 2 parport_pc 32114 0 ppdev 12849 0 binfmt_misc 17292 1 snd_hda_codec_hdmi 31426 1 snd_hda_codec_conexant 52460 1 uvcvideo 67271 0 videodev 85626 1 uvcvideo snd_hda_intel 28358 2 snd_hda_codec 91859 3 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec joydev 17393 0 snd_pcm 80435 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 i915 509554 9 drm_kms_helper 32889 1 i915 snd_rawmidi 25241 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28932 2 snd_pcm,snd_seq drm 196290 5 i915,drm_kms_helper snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq mei 36466 0 mac80211 393421 0 snd 55902 14 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 13575 0 intel_ips 17753 0 btusb 18160 2 i2c_algo_bit 13199 1 i915 soundcore 12600 1 snd bluetooth 148839 23 rfcomm,bnep,btusb cfg80211 172427 1 mac80211 psmouse 63474 0 serio_raw 12990 0 snd_page_alloc 14108 2 snd_hda_intel,snd_pcm sparse_keymap 13658 1 ideapad_laptop wmi 18744 0 video 18908 1 i915 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp ahci 21634 2 libahci 25761 1 ahci r8169 47200 0 ----##nm-tool NetworkManager Tool State: asleep Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: r8169 State: unmanaged Default: no HW Address: 88:AE:1D:DE:5F:9C Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on ----##lshw -C network *-network UNCLAIMED description: Network controller product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:05:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d6400000-d6401fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 02 serial: 88:ae:1d:de:5f:9c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=192.168.0.100 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d2410000-d2410fff memory:d2400000-d240ffff memory:d2420000-d243ffff

  Read the article

• DBA in Space

  - by Neil Davidson

  Every now and then, you come across an idea that makes your heart jump and your skin tingle. That happened to me a few months ago, when Richard and Anthony pitched a small group of us an idea. "It's called DBA in Space", Richard said. I don't remember the rest of the pitch. "DBA in Space" is one of those phrases that's so simple, remarkable and clear that it sticks and it sticks hard. Sure, lots of people have done much hard, gritty work over the past few months to make it happen. Sure, there's...(read more)

  Read the article

• KVM Virtual guest Paused on Reboot

  - by David Hamilton

  I'm running REHL 6 and just installed a Ubuntu Server Guest via KVM set to start at boot. This works correctly and the guest loads, but it loads "paused" and requires that I manually un-pause it. Can someone give me a hint as to how I can I get the Guest OS to actually become active on boot? Here is the libvert dump as requested...Also tried libvert auto-start --- no effect. <domain type='kvm' id='1'> <name>MailServer</name> <uuid>a61dae75-1f5c-d536-718f-3c615d9b4868</uuid> <memory>4194304</memory> <currentMemory>4194304</currentMemory> <vcpu>4</vcpu> <os> <type arch='x86_64' machine='rhel6.0.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='none'/> <source file='/home/MailServer/MailServer-1.img'/> <target dev='hda' bus='ide'/> <alias name='ide0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> <alias name='ide0-1-0'/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <alias name='ide0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:cd:f9:9f'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/1'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='5900' autoport='yes'/> <sound model='ac97'> <alias name='sound0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </sound> <video> <model type='cirrus' vram='9216' heads='1'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='selinux'> <label>system_u:system_r:svirt_t:s0:c211,c271</label> <imagelabel>system_u:object_r:svirt_image_t:s0:c211,c271</imagelabel> </seclabel></domain>

  Read the article

• Ubuntu - Black Screen After Suspend

  - by EssAm

  I used Ubuntu with no problems and I upgraded to 11.10 and everything was fine. But when I did my first suspend I was not able to boot again, all I got was a black screen no bios screen, nothing just blank, I tried doing hard reset but when I power on again same happens. I tried ctrl+alt+delete F1-F12 but i think the keyboard is not working, also tried booting from CD but all I got was blank screen, the hard disk light is not blinking at all so i'm assuming it's not trying to boot. My laptop is Toshiba satellite with ATI Radeon graphics. Hibernate was working fine though. I searched the net for solutions but with no luck. Any ideas?

  Read the article

• Symlink are using both locations?

  - by Tiago Rossi

  Ive made a research and didnt found any answers, so I decided to ask here. To make you know, the /dev/sda2 disk of my WHM/Cpanel webserver got 100% full. The /var/ folder are the /dev/sda2 and I've found the reason of that isse are the /var/lib/mysql folder. To fix it I need to move the /var/lib/mysql folder from /dev/sda2 to /home/ where I have a lot of space in disk. Then I used the command lines: service mysql stop cp -r -p /var/lib/mysql/ /home/databasesmysql/ mv /var/lib/mysql /var/lib/mysql.backup/ ln -s /home/databasesmysql/ /var/lib/mysql service mysql start Ok, now to check if its running at the new location I just renamed the /var/lib/mysql to /var/lib/mysql.backup and MySQL stopped working. Also when I rename the /home/databasesmysql/ folder MySQL also stop to work. I dont know whats happening, the symlink are using both locations? Thanks very much.

  Read the article

• Lubuntu 12.04 installation trouble

  - by Evaggelos Tsampazis

  I have i problem! I can't install the Lubuntu 12.04 on my old pc. I only get to the point where I have entered all the needed information (hard drive, username, password etc). When the installation wizard is starting to copy files from the cd to the hard drive, I get after about one minute a blank sreen with only themouse cursor! I can move the mouse cursor but the whole procegure is stoped! Nothing happens after that! My PC: Compaq Pressario 7000 Pentium III 933 MHz 768 MB RAM Any idea how to solve it?? Thanks!!!

  Read the article

• Why is it necessary to install EFI/rEFInd/UEFI/... on a SD Card since the Macbook Pro seems to already have it?

  - by user170794

  Dear askubuntu members, I own a Macbook Pro (late 2009) and when I boot the laptop and hold the alt key meanwhile, there is a EFI screen, so EFI is installed on... the firmware? I had a few troubles with my hard disk, so I had to change it, but I haven't installed OS X, I have only installed Ubuntu and still the EFI screen is there which is surely a good thing. As the new hard disk is making troubles again, I am using Puppy Linux, booting from a CD each time, which is unconfortable. So I am trying to have Ubuntu installed on a SD Card. After having spent many months on the internet grabing informations anywhere I can and trying several things, I applied this method: http://www.weihermueller.de/mac/ I succeeded in making one SD Card recognizable by the EFI of my laptop (holding alt key @ boot), but nothing installed on it yet as I fear to lose the recognizable-by-EFI part. I haven't succeded in producing the same result on another SD Card. I have a bootable USB key of Ubuntu (yipee) which works like a live CD, made with the help of Universal Linux UDF Creator, found there: http://www.pendrivelinux.com/universal-usb-installer-easy-as-1-2-3/ on which I have put Ubuntu 13.04 64bit, retrieved from the official deposits. Eventhough I have to add the "nouveau.noaccel=1" option to the grub command line launching Linux, it works (yipee again) properly as a live cd. When installing Ubuntu I come across the "where do I wanna put Ubuntu" window, I partition another SD Card in: the EFI part (40MB) the Linux part (15GB< <16GB) The installation works fine and finishes with no problem. But at the reboot, the SD Card where Linux is installed is not recognized by the EFI, the icons are : the CD (Puppy Linux), the USB stick (from Linux UDF Creator), the hard drive (the formerly-working Ubuntu 12) but no fourth icon of the SD Card whatsoever. As the title of this thread suggests, I am wondering: why there is a need for EFI to be installed on the SD Card since EFI seems to be on my laptop anyway? why EFI has to be on a different partition than the Linux's one? How do both parts communicate? why the EFI part on the SD Card made with the help of the live-USB key isn't recognized? on the EFI partition, there is a folder named "EFI" which contains another folder named "ubuntu" which contains a file named "grubx64.efi", why is there a thing called grub? Is it the Linux's grub where one can chose either to boot, to boot in safe mode, etc.? Thank you for your patience, looking forward for any kind of answer, Julien

  Read the article

• Should I incorporate exit cost into choosing a solution

  - by Mr Happy

  I'm currently choosing between two viable software designs/solutions. Solution 1 is easy to implement, but will lock some data in a propriaty format, and will be hard to change later. Solution 2 is hard to implement, but will be a lot easier to change later on. Should I go YAGNI on this or should I incorporate the exit cost in the decision making? Or asked differently, is the exit cost part of the TCO? I'm thinking of going back to the customer with this to ask wether or not he thinks the exit costs are relevant, but I'd like to know what the community thinks first. P.S. Is exit cost the correct term?

  Read the article

• How to Banish Duplicate Photos with VisiPic

  - by Jason Fitzpatrick

  You meant well, you intended to be a good file custodian, but somewhere along the way things got out of hand and you’ve got duplicate photos galore. Don’t be afraid to delete them and lose important photos, read on as we show you how to clean safely. Deleting duplicate files, especially important ones like personal photos, makes a lot of people quite anxious (and rightfully so). Nobody wants to be the one to realize that they deleted all the photos of their child’s first birthday party during a hard drive purge gone wrong. In this tutorial we’re going to show you how to go beyond the limited reach of  tools which simply compare file names and file sizes. Instead we’ll be using a program that combines that kind of comparison with actual image analysis to help you weed out not just perfect 1:1 file duplicates but also those piles of resized for email images, cropped images, and other modified images that might be cluttering up your hard drive. How to Banish Duplicate Photos with VisiPic How to Make Your Laptop Choose a Wired Connection Instead of Wireless HTG Explains: What Is Two-Factor Authentication and Should I Be Using It?

  Read the article

• Ransomware: Why This New Malware is So Dangerous and How to Protect Yourself

  - by Chris Hoffman

  Ransomware is a type of malware that tries to extort money from you. One of the nastiest examples, CryptoLocker, takes your files hostage and holds them for ransom, forcing you to pay hundreds of dollars to regain access. Most malware is no longer created by bored teenagers looking to cause some chaos. Much of the current malware is now produced by organized crime for profit and is becoming increasingly sophisticated. How Ransomware Works Not all ransomware is identical. The key thing that makes a piece of malware “ransomware” is that it attempts to extort a direct payment from you. Some ransomware may be disguised. It may function as “scareware,” displaying a pop-up that says something like “Your computer is infected, purchase this product to fix the infection” or “Your computer has been used to download illegal files, pay a fine to continue using your computer.” In other situations, ransomware may be more up-front. It may hook deep into your system, displaying a message saying that it will only go away when you pay money to the ransomware’s creators. This type of malware could be bypassed via malware removal tools or just by reinstalling Windows. Unfortunately, Ransomware is becoming more and more sophisticated. One of the latest examples, CryptoLocker, starts encrypting your personal files as soon as it gains access to your system, preventing access to the files without knowing the encryption key. CryptoLocker then displays a message informing you that your files have been locked with encryption and that you have just a few days to pay up. If you pay them $300, they’ll hand you the encryption key and you can recover your files. CryptoLocker helpfully walks you through choosing a payment method and, after paying, the criminals seem to actually give you a key that you can use to restore your files. You can never be sure that the criminals will keep their end of the deal, of course. It’s not a good idea to pay up when you’re extorted by criminals. On the other hand, businesses that lose their only copy of business-critical data may be tempted to take the risk — and it’s hard to blame them. Protecting Your Files From Ransomware This type of malware is another good example of why backups are essential. You should regularly back up files to an external hard drive or a remote file storage server. If all your copies of your files are on your computer, malware that infects your computer could encrypt them all and restrict access — or even delete them entirely. When backing up files, be sure to back up your personal files to a location where they can’t be written to or erased. For example, place them on a removable hard drive or upload them to a remote backup service like CrashPlan that would allow you to revert to previous versions of files. Don’t just store your backups on an internal hard drive or network share you have write access to. The ransomware could encrypt the files on your connected backup drive or on your network share if you have full write access. Frequent backups are also important. You wouldn’t want to lose a week’s worth of work because you only back up your files every week. This is part of the reason why automated back-up solutions are so convenient. If your files do become locked by ransomware and you don’t have the appropriate backups, you can try recovering them with ShadowExplorer. This tool accesses “Shadow Copies,” which Windows uses for System Restore — they will often contain some personal files. How to Avoid Ransomware Aside from using a proper backup strategy, you can avoid ransomware in the same way you avoid other forms of malware. CryptoLocker has been verified to arrive through email attachments, via the Java plug-in, and installed on computers that are part of the Zeus botnet. Use a good antivirus product that will attempt to stop ransomware in its tracks. Antivirus programs are never perfect and you could be infected even if you run one, but it’s an important layer of defense. Avoid running suspicious files. Ransomware can arrive in .exe files attached to emails, from illicit websites containing pirated software, or anywhere else that malware comes from. Be alert and exercise caution over the files you download and run. Keep your software updated. Using an old version of your web browser, operating system, or a browser plugin can allow malware in through open security holes. If you have Java installed, you should probably uninstall it. For more tips, read our list of important security practices you should be following. Ransomware — CryptoLocker in particular — is brutally efficient and smart. It just wants to get down to business and take your money. Holding your files hostage is an effective way to prevent removal by antivirus programs after it’s taken root, but CryptoLocker is much less scary if you have good backups. This sort of malware demonstrates the importance of backups as well as proper security practices. Unfortunately, CryptoLocker is probably a sign of things to come — it’s the kind of malware we’ll likely be seeing more of in the future.     

  Read the article

• How to access photos from my Genius G-Shot P7545 camera?

  - by Florin

  I have a Genius G-Shot P7545 camera. In Windows I had just to plug in the camera to the usb and acces it like a usb stick. I tried to do that in Ubuntu 10.10 with no result. How can I acces the photots? With these comands I get: lsusb Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 015: ID 0784:1692 Vivitar, Inc. Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xcf5acf5a Device Boot Start End Blocks Id System /dev/sda1 * 1 2550 20478976 83 Linux /dev/sda3 2550 19458 135810048 f W95 Ext'd (LBA) /dev/sda5 2550 19458 135809024 83 Linux Unable to read /dev/sdb

  Read the article

• What's the best version control/QA workflow for a legacy system?

  - by John Cromartie

  I am struggling to find a good balance with our development and testing process. We use Git right now, and I am convinced that ReinH's Git Workflow For Agile Teams is not just great for capital-A Agile, but for pretty much any team on DVCS. That's what I've tried to implement but it's just not catching. We have a large legacy system with a complex environment, hundreds of outstanding and undiscovered defects, and no real good way to set up a test environment with realistic data. It's also hard to release updates without disrupting users. Most of all, it's hard to do thorough QA with this process... and we need thorough testing with this legacy system. I feel like we can't really pull off anything as slick as the Git workflow outlined in the link. What's the way to do it?

  Read the article

• Unable to install Ubuntu 12.10 on windows 8 machine/ error no5

  - by JOBIN VARGHESE

  installing crashes at halfway of 'copying files' showing an i\o device error error no5; there was problem in beginning of installation too, ubuntu was not detecting the installed windows 8. my system is a dell inspiron 5520 laptop ,with 1 tb WDC hard disk in GPT ,with EFI . my current partition is like 102 mb EFI SYSTEM partition 200 gb Windows 8 ntfs 22 gb root Ext4 8 gb swap 20 db home Ext4 680 gb ntfs Drive for storing all my files. i tried both dvd disc and usb drive, both resulted in same error. inbuild dell hardware diagnosis utility showed both hard disk and dvd drive as healthy what may be the reason and how can i install ubuntu along side my windows 8?

  Read the article

• Boot path not found, cannot start OS

  - by Dustin

  My desktop is 12.04 64bit, and it cannot boot from the hard drive anymore. When I attempt to it just is stuck on a blank screen with an blinking dash, and nothing happens. I checked with the bios trouble shoot for problems and it said that no boot path could be found. I do not know why this is happening, but need to fix it because it used to boot up normally. What I need to know is how to fix it. I can boot into a live DVD. Also, there were a few boots I would attempt to boot into a live USB, then it would boot to the hard drive, but that does not work any more. So with the live DVD (it is an 10.04 LTS 32bit), is there any means to correct the boot path from the live DVD? Thank you for your time and answers.

  Read the article

• How can I avoid the random restart of the xserver?

  - by Bernd

  I'm using a desktop pc with 64bit Ubuntu 12.04 (Kernel 3.2.0-24-generic). Hardware specs are - Intel Core i7 CPU 860 @ 2,80GHz x 8 - Nvidia GeForce GTS 250 - 750 GB Hard Disk ATA WDC WD7501AALS-00E3A0 (for my /home partition) - 128 GB Solid-State Disk ATA PLEXTOR PX-128M2S (for all other partitions) Since I reinstalled the PC with Ubuntu 12.04 the xserver restarts randomly. Most times when I watch a video in the browser (maybe a flash issue?) but sometimes the restart/crash appears when I'm working in an text-editor. How can I locate the problem? Which information is needed for a useful answer?

  Read the article

• Can't see my partitions after grub recovery

  - by dimbo

  I stupidly inserted the windows CD into my dual boot Ubuntu 11.10 / windows xp system. I just wanted to see if I could install windows on my external usb HD, but didn't actually go ahead with the install. It seems like the windows CD messed up my MBR and I had to use boot-repair and the ubuntu 11.10 live CD to gain access to ubuntu again. It seems to boot up a little differently (slower) but works. However, I now cant see any of my partitions in nautilus (there are 3). When I open gparted, it just shows my whole hard drive as unallocated (I know it has a windows partition that works and my ubuntu partition that I am using now). If I insert a usb pen, it is also not visible in nautilus but in gparted shows up as a FAT32 partition (which is correct although I cannot access it). sudo fdisk -l gives the following : demian@dimbo-TP:~$ sudo fdisk -l [sudo] password for demian: omitting empty partition (5) Disk /dev/sda: 320.1 GB, 320072933376 bytes 240 heads, 63 sectors/track, 41345 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x877b877b Device Boot Start End Blocks Id System /dev/sda1 * 63 63842309 31921123+ 7 HPFS/NTFS/exFAT /dev/sda2 63844350 133484084 34819867+ 5 Extended /dev/sda3 127636488 133484084 2923798+ 82 Linux swap / Solaris /dev/sda4 133484085 625137344 245826630 83 Linux /dev/sda5 63844352 123445247 29800448 83 Linux /dev/sda6 123447296 127635455 2094080 82 Linux swap / Solaris Disk /dev/sdb: 8100 MB, 8100249600 bytes 12 heads, 40 sectors/track, 32960 cylinders, total 15820800 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdb1 * 5992 15820799 7907404 c W95 FAT32 (LBA) Here is my grub.conf file. Like I said before, I had to use the 'boot-repair' utility with the live cd to get grub working again. I think that this utility maybe created a new grub for me because the startup is definitely not the same. The screen goes blank for a while, and then the ubuntu loading dots come up for a brief moment (instead of during the whole startup process) before the dektop is displayed. Anyway : # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=10 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.0.0-12-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a linux /boot/vmlinuz-3.0.0-12-generic root=UUID=5349ff67-b7b7-489f-a881-ae49c1dcd84a ro quiet splash vt.handoff=7 initrd /boot/initrd.img-3.0.0-12-generic } menuentry 'Ubuntu, with Linux 3.0.0-12-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a echo 'Loading Linux 3.0.0-12-generic ...' linux /boot/vmlinuz-3.0.0-12-generic root=UUID=5349ff67-b7b7-489f-a881-ae49c1dcd84a ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.0.0-12-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Microsoft Windows XP Professional (on /dev/sda1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 72A89361A89322A1 drivemap -s (hd0) ${root} chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### How can I get things back to normal. Thanks, Demian.

  Read the article

• installed ubuntu 13.04 but no wireless or wired connection available

  - by James

  after having installed ubuntu 13.04 i can not connect to the internet wirelessly or wired? can only connect to internet by using "try ubuntu" via ethernet cable, ive tried seeking help in so many different ways yet getting no positive outcome at all, will someone please explain why i can only connect with ethernet while i have the cd in the tray? ive also tried downloading b43 drivers to connect to the internet but apparently i dont have enough disk space, what is going on here? i have the disk in the tray now at the screen where you can either try or install, if someone could give me a step by step from here it would probably cut out all this hassle of me not knowing whats going on

  Read the article

• I studied electrical engineering. Can I work as a developer? [closed]

  - by FailedDev

  A while ago I finished my Msc in Electrical Engineering and started working as an engineering consultant where I mostly do development work. I am good at picking up languages/technologies tools. I have fiddled with C/C++/C#/perl/ant/bash/html/css etc. Although I have never had a complain for my work, rather the contrary, I just feel that some day, someone will ask me a real hard task which would maybe seem rather trivial for a computer scientist but hard for me. Should I read/do something to become a better developer. Should I pick up a book about design patterns or algorithms for example? Is this normal that I have this kind of "fear"? Sorry if this is the wrong place to post this question. Please notify me so I can close it if this is the case.

  Read the article

< Previous Page | 192 193 194 195 196 197 198 199 200 201 202 203  | Next Page >