Search Results

Search found 7583 results on 304 pages for 'roger guess'.

Page 198/304 | < Previous Page | 194 195 196 197 198 199 200 201 202 203 204 205  | Next Page >

  • IPCop Packet Mangling

    - by Zenham
    I've found myself in a pickle replacing an old firewall for a client this afternoon. I'm configuring their new IPCop firewall (1.4.21), Zerina OpenVPN addon is installed. What I need to do: There are three network interfaces, currently set up as red (WAN), green (LAN, 192.168.20.0/24) and orange (remote network 10.1.20.0/24). The orange interface is a direct fiber link to another organization. Simple description: Traffic and networks appear to be properly configured at this point, but I have many (150+) specific IPs on the LAN which, when accessing the resources on the 10.1.20.x network, need to be mangled to appear to be coming from the 10.1.20.0/24 network (and return traffic properly delivered). The routing on the far side was configured earlier and should be fine, but I need to redirect any packets coming across destined for those IPs to end up at their proper destination. The addressing is fixed and predictable (ie. 192.168.20.125 - 10.1.20.125). I need to insert whatever rules I have into the IPCop ruleset through /etc/rc.local I know, I'm just not sure about how I should structure this. There's CUSTOMOUTPUT and CUSTOMINPUT targets, both which currently just consist of the single rule redirecting packets to the OVPNOUTPUT/OVPNINPUT targets, so I'm guessing I should insert a rule matching outbound packets destined for the 10.1.20.x network and redirecting to a new target (maybe called TO-ORANGE) and a rule at the top of CUSTOMINPUT which redirects to a FROM-ORANGE target. Under those targets, I would have rules which do the IP matching and mangling. Am I approaching this right? If so, I'm not very familiar with mangle, and would appreciate seeing examples of how to write that source-IP rewrite. If not, how would you suggest doing this? TIA! edit: I notice additionally that the nat table has CUSTOMPREROUTING and CUSTOMPOSTROUTING targets, I guess I could alternatively post the rules in there....

    Read the article

  • LDAP change user pass on client

    - by Sean
    I am trying to allow ldap users to change their password on client machines. I have tried pam every which way I can think of /etc/ldap.conf & /etc/pam_ldap.conf, as well. At this point I'm stuck. Client: Ubuntu 11.04 Server: Debian 6.0 The current output is this: sobrien4@T-E700F-1:~$ passwd passwd: Authentication service cannot retrieve authentication info passwd: password unchanged /var/log/auth.log gives this during the command: May 9 10:49:06 T-E700F-1 passwd[18515]: pam_unix(passwd:chauthtok): user "sobrien4" does not exist in /etc/passwd May 9 10:49:06 T-E700F-1 passwd[18515]: pam_ldap: ldap_simple_bind Can't contact LDAP server May 9 10:49:06 T-E700F-1 passwd[18515]: pam_ldap: reconnecting to LDAP server... May 9 10:49:06 T-E700F-1 passwd[18515]: pam_ldap: ldap_simple_bind Can't contact LDAP server getent passwd |grep sobrien4 (note keeping short since testing with that account, however it outputs all ldap users): sobrien4:Ffm1oHzwnLz0U:10000:12001:Sean O'Brien:/home/sobrien4:/bin/bash getent group shows all ldap groups. /etc/pam.d/common-password (Note this is just the most current, I have tried a lot of different options): password required pam_cracklib.so retry=3 minlen=8 difok=3 password [success=1 default=ignore] pam_unix.so use_authtok md5 password required pam_ldap.so use_authtok password required pam_permit.so Popped open wireshark as well, the server & client are talking. I have the password changing working on the server. I.E. the server that runs slapd, I can log in with the ldap user and change the passwords. I tried copying the working configs from the server initially and no dice. I also tried cloning it, and just changing ip & host, and no go. My guess is that the client is not authorized by ip or hostname to change a pass. Pertaining to the slapd conf, I saw this in a guide and tried it: access to attrs=loginShell,gecos by dn="cn=admin,dc=cengineering,dc=etb" write by self write by * read access to * by dn="cn=admin,dc=cengineering,dc=etb" write by self write by * read So ldap seems to be working okay, just can't change the password.

    Read the article

  • MacBook Pro battery capacity 65K mAh

    - by Alexander Gladysh
    I have a 15" MacBook Pro 3.1 (that is Late 2007 model AFAIR). I've bought it new a couple of years ago. Recently its on-battery power lifespan became very short (30 to 10 minutes). When my notebook turns itself off due to "low battery" and I press the small button on the battery itself, all LED lights are alight, indicating full charge. When I plug in the power adapter, my Mac displays that "battery is fully charged, finishing charging process" (I have a Russian OS X 10.5.7, so that is a rough translation), but the LEDs on battery itself display (seemingly accurate) status that there are one or two "LEDs still not charged". My battery have as few as 37 recharge cycles (yes, I've neglected calibration over the time I've used it). Battery info programs like iBatt2 report battery capacity of 65 337 mAh (with by-design capacity of 5600 mAh). I get it that something went wrong with battery electronics. I've tried resetting my Mac's PRAM and SMC, it did not changed anything. Now I'm trying to recalibrate the battery, but looks like it does not help as well. Will try to recalibrate it several times in a row. I'd buy a new battery if I knew if it is battery fault, not a notebook's. Any suggestions? Update: After recalibration, my battery status now displays battery capacity of 1500 mAh. But with every recalibration (or simply when I use notebook without power adapter plugged in) this number changes in the range from 200 mAh to 1700 mAh. LEDs on battery now are synchronous with what nodebook thinks on the charge level. Also I've noticed that cycle count changes rather slowly. It is now 39, it was 37 when I've started recalibration, and I went through the process at least ten times... So, the main question is: does it look like that replacing the battery would help me (or does it look like this is notebook's problem)? I guess I should try replacing the battery.

    Read the article

  • How to automatically remove Flash history/privacy trail? Or stop Flash from storing it?

    - by Arjan van Bentem
    Many people have heard about third-party cookies, and some browsers even block those by default. Some people may even be using Private Browsing modes. However, only few seem to realise that Adobe's Flash player also leaves a cross-browser trail on your local hard drive, and allows for sending cookie-like information back to the server, including third-party sites. And because it is a plugin, Flash does not take any of the browser's privacy settings into account. Sorry for the long post, but first some details about why using Flash raises a privacy concern, followed by the results of my tests: The Flash player keeps a cross-browser history of the domain names of the Flash-sites your computer has visited. Unlike your browser's history, this history is not limited to a certain number of days. History is also recorded while using so-called Private Browsing modes. It is stored on your hard drive (though, as described below, without going to Adobe's site you won't know what is stored). I am not sure if any date and time information is kept about each visit, but to see the domain names: right-click on some Flash content, open the settings dialog, and click the Help icon or click the Advanced button within the Privacy tab. This opens a browser to the help pages on Adobe.com, where one can click through to the Website Storage Settings panel. One can clear the existing list, but one cannot stop it from being recorded again. Flash allows for storing data on your local hard drive, using so-called Local Shared Objects (aka "Flash Cookies"). Just like HTTP cookies, this data can be sent back to the server, for tracking purposes. They are cross-browser, have no expiration date, and no user defined maximum lifetime can be set in the Flash preferences either. These not being HTTP cookies, they are (of course) not blocked by a browser's cookies preferences and are not removed when the normal HTTP cookies are deleted. Adobe has announced that version 10.1 will obey Private Browsing in most popular browsers, but unfortunately no word about also removing the data whenever normal cookies are deleted manually. And its implementation might be confusing: [..] if the browser is in normal browsing mode when the Flash Player instance is created, then that particular instance will forever be in normal browsing mode (private browsing is turned off). Accordingly, toggling private browsing on or off without refreshing the page or closing the private browsing window will not impact Flash Player. Local Shared Objects are not limited to the site you visit, and third-party storage is enabled by default. At the Global Storage Settings panel one can deselect the default Allow third-party Flash content to store data on your computer. Because of the cross-browser and expiration-less nature (and the fact that few people know about it), I feel that the cross-browser third-party Flash Cookies are more dangerous for visitor tracking than third-party normal HTTP cookies. They are even used to restore plain HTTP cookies that the user tried to delete: "All advertisers, websites and networks use cookies for targeted advertising, but cookies are under attack. According to current research they are being erased by 40% of users creating serious problems," says Mookie Tenembaum, founder of United Virtualities. "From simple frequency capping to the more sophisticated behavioral targeting, cookies are an essential part of any online ad campaign. PIE ["Persistent Identification Element"] will give publishers and third-party providers a persistent backup to cookies effectively rendering them unassailable", adds Tenembaum. [..] To justify this tracking mechanism, UV's Tenembaum said, "The user is not proficient enough in technology to know if the cookie is good or bad, or how it works." When selecting None (zero KB) for Specify the amount of disk space that website websites that you haven't yet visited can use to store information on your computer, and checking Never ask again then some sites do not work. However, the same site might work when setting it to None but without selecting Never ask again, and then choose Deny whenever prompted. Both options would result in zero KB of data being allowed, but the behaviour differs. The plugin also provides a Flash Player cache for Adobe-signed files. I guess these files are not an issue. So: how to automatically delete that information? On a Mac, one can find a settings.sol file and a folder for each visited Flash-website in: $HOME/Library/Preferences/Macromedia/Flash Player/macromedia.com/support/flashplayer/sys/ Deleting the settings.sol file and all the folders in sys, removes the trail from the settings panels. However, the actual Local Shared Ojects are elsewhere (see Wikipedia for locations on other operating systems), in a randomly named subfolder of: $HOME/Library/Preferences/Macromedia/Flash Player/#SharedObjects But then: how to remove this automatically? Simply removing the folders and the settings.sol file every now and then (like by using launchd or Windows' Task Scheduler) may interfere with active browsers. Or is it safe to assume that, given the cross-browser nature, the plugin would not care if things are removed while it is active? Only clearing during log-off may not work for those who hibernate all the time. Firefox users can install BetterPrivacy or Objection to delete the Local Shared Objects (for all others browsers as well). I don't know if that also deletes the trail of website domain names. Or: how to stop Flash from storing a history trail? Change of plans: I'm currently testing prohibiting Flash to write to its own sys and #SharedObjects folders. So far, Flash has not tried to restore permissions (though, when deleting the folders, Flash will of course recreate them). I've not encountered any problems but this may take some while to validate, using multiple browsers and sites. I've not yet found a log that reports errors. On a Mac: cd "$HOME/Library/Preferences/Macromedia/Flash Player/macromedia.com/support/flashplayer" rm -r sys/* chmod u-w sys cd "$HOME/Library/Preferences/Macromedia/Flash Player" # preserve the randomly named subfolders (only preserving the latest would suffice; see below) rm -r \#SharedObjects/*/* chmod -R u-w \#SharedObjects I guess the above chmods cannot be achieved on an old Windows system (I'm not sure about XP and Vista?). Though maybe on Windows one could replace the folders sys and #SharedObjects with dummy files with the same names? Anyone? Obviously, keeping Flash from storing those Local Shared Objects for all sites may cause problems. Some test results (Flash 10 on Mac OS X): When blocking the sys folder (even when leaving the #SharedObjects folder writable) then YouTube won't remember your volume settings while viewing multiple videos. Temporarily allowing write access to the blocked folders while visiting trusted sites (to only create folders for domains you like, maybe including references in settings.sol) solves that. This way, for YouTube, Flash could be allowed to write to sys/#s.ytimg.com and #SharedObjects/s.ytimg.com, while Flash could not create new folders for other domains. One may also need to make settings.sol read-only afterwards, or delete it again. When blocking both the sys and #SharedObjects folders, YouTube and Vimeo work fine (though they might not remember any settings). However, Bits on the Run refuses to even show the video player. This is solved by temporarily unblocking the #SharedObjects folder, to allow Flash to create a subfolder with some random name. Within this folder, it would create yet another folder for the current Flash website (content.bitsontherun.com). Removing that website-specific folder, and blocking both #SharedObjects and the randomly named subfolder, still seems to allow Bits on the Run to operate, even though it still cannot write anything to disk. So: the existence of the randomly named subfolder (even when write protected) is important for some sites. When I first found the #SharedObjects folder, it held many subfolders with random names, some created on the very same day. I wonder when Flash decides it wants a new folder, and how it determines (and remembers) that random name. For a moment I considered not blocking write access for sys and #SharedObjects, but explicitly creating read-only folders for well-known third-party tracking domains (like based on a list from, for example, AdBlock Plus). That way, any other domain could still create Local Shared Objects. But the list would be long, and the domains from AdBlock Plus are probably all third-party domains anyway, so disabling Allow third-party Flash content to store data on your computer might have the very same result. Any experience anyone? (Final notes: if the above links to the settings panels do not work in the future, then use the URL that is known to Flash player as a starting point: www.adobe.com/go/settingsmanager. See also "You Deleted Your Cookies? Think Again" at Wired.com -- which uses Flash cookies itself as well... For the very suspicious using Time Machine: you may want to exclude both folders, for each user, and remove the trace that is already on your backup.)

    Read the article

  • Sharepoint db issue after DB move to SQL 08

    - by JohnyV
    Recently we have moved our sharepoint 2007 db from sql 2000 server to 2008 x64 SQL server. All seems well, however there is a problem where the sql server stops running and the service has to be restarted. The errors mention insufficient internal memory etc. I have tried to start the db using -g384 which is the default in sql 2000 but 256 is default for 2008 I believe. This has not rectified the issue. I was advised that perhaps the issue may be rectified by upgrading to wss 3.0 sp2 however When I have tried to install this i get another error post sp2 update and have to refer back to a vm snapshot. The error after the service pack is Server error: http://go.microsoft.com/fwlink?LinkID=96177 So I guess I have a few questions How can I fix the first issue and the 2nd issue. I have checked out many forums and posts and have tried a few things and still get no joy. Any assistance would be great. UPDATE I have fixed the Server error: http://go.microsoft.com/fwlink?LinkID=96177 the i needed to run the wss sp2 as well as the office servers sp2 then the config wizard then the moss configuration worked. The errors I am getting in SQL are SQL Server was unable to run a new system task, either because there is insufficient memory or the number of configured sessions exceeds the maximum allowed in the server. Verify that the server has adequate memory. Use sp_configure with option 'user connections' to check the maximum number of user connections allowed. Use sys.dm_exec_sessions to check the current number of sessions, including user processes. A read operation on a large object failed while sending data to the client. A common cause for this is if the application is running in READ UNCOMMITED isolation level. The connection will be terminated. There is insufficient system memory in resource pool 'internal' to run this query. These errors are by a user that was created as a service for sharepoint.

    Read the article

  • ssh-agent on ubuntu rapidly restarts

    - by Santa Claus
    I am attempting to use ssh-agent on Ubuntu 13.10 so that I will not have to enter my passphrase to unlock a key every time I want to use ssh or git. As you can see below, ssh-agent appears to be restarting for some reason. These commends were executed within a period of less than 5 seconds: andrew@zaphod:~$ ssh-agent SSH_AUTH_SOCK=/tmp/ssh-pqm5J0s70NxG/agent.2820; export SSH_AUTH_SOCK; SSH_AGENT_PID=2821; export SSH_AGENT_PID; echo Agent pid 2821; andrew@zaphod:~$ ssh-agent SSH_AUTH_SOCK=/tmp/ssh-VpkOH2WKjT1M/agent.2822; export SSH_AUTH_SOCK; SSH_AGENT_PID=2823; export SSH_AGENT_PID; echo Agent pid 2823; andrew@zaphod:~$ ssh-agent SSH_AUTH_SOCK=/tmp/ssh-EQ6X9JHNiBOO/agent.2824; export SSH_AUTH_SOCK; SSH_AGENT_PID=2825; export SSH_AGENT_PID; echo Agent pid 2825; andrew@zaphod:~$ ssh-agent SSH_AUTH_SOCK=/tmp/ssh-8Iij8kFkaapz/agent.2826; export SSH_AUTH_SOCK; SSH_AGENT_PID=2827; export SSH_AGENT_PID; echo Agent pid 2827; andrew@zaphod:~$ My guess is that ssh-agent is crashing, but how would I know? What log file would it log to?

    Read the article

  • Why does bash sometimes think my $HOME isn't the correct directory?

    - by Adam Yanalunas
    Like the title says it seems that bash sometimes misidentifies my $HOME. This cropped up after a seemingly unique series of events that I will now replay in broad strokes. Running OS X 10.6 with normal, local account Work binds my account to Active Directory Much time passes with no issues Set up rvm to manage Ruby installs (this becomes important later) Upgraded to OS X 10.7 a few days ago After successful install, attempted to log in, was presented with "Must reset password" dialog that never allowed a password to be reset. Would simply shake the box after new password was entered. Much googling was done. Much more googling was done. Swearing was had. Logged in as root, created new account, set as admin, deleted /Users/[new account], renamed /Users/[old account] to /Users/[new account] Logged out of root, logged into new account with no issues After OS X asking for a my account password a few times to update Keychain and other system-level stuff it was back to business as usual. Opened Terminal, cd to project folder, tried "rails server" and was presented with: /usr/local/lib/ruby/1.9.1/rubygems/dependency.rb:247:in to_specs': Could not find rails (>= 0) amongst [] (Gem::LoadError) from /usr/local/lib/ruby/1.9.1/rubygems/dependency.rb:256:into_spec' from /usr/local/lib/ruby/1.9.1/rubygems.rb:1210:in gem' from /usr/local/bin/rails:18:in' Ran through a few exercises, decided to rm -rf ~/.rvm and reinstall. Running a --trace on the rvm installer shows it dies on this line: mkdir: /Users/[old account]: Permission denied Scrolling back through the --trace log I see many more mentions of /Users/[old account]. When inspect the install script the offending line is looking at "${HOME}/.rvm" as it tries to run the mkdir. To my confusion I also see mentions of /Users/[new account] in the log. I've tried exporting a new HOME in my .bash_profile to no luck. Can anyone guess why /Users/[old account] would still be kicking around?

    Read the article

  • MaxStartups and MaxSessions configurations parameter for ssh connections?

    - by Webby
    I am copying the files from machineB and machineC into machineA as I am running my below shell script on machineA. If the files is not there in machineB then it should be there in machineC for sure so I will try copying the files from machineB first, if it is not there in machineB then I will try copying the same files from machineC. I am copying the files in parallel using GNU Parallel library and it is working fine. Currently I am copying 10 files in parallel. Below is my shell script which I have - #!/bin/bash export PRIMARY=/test01/primary export SECONDARY=/test02/secondary readonly FILERS_LOCATION=(machineB machineC) export FILERS_LOCATION_1=${FILERS_LOCATION[0]} export FILERS_LOCATION_2=${FILERS_LOCATION[1]} PRIMARY_PARTITION=(550 274 2 546 278) # this will have more file numbers SECONDARY_PARTITION=(1643 1103 1372 1096 1369 1568) # this will have more file numbers export dir3=/testing/snapshot/20140103 find "$PRIMARY" -mindepth 1 -delete find "$SECONDARY" -mindepth 1 -delete do_Copy() { el=$1 PRIMSEC=$2 scp david@$FILERS_LOCATION_1:$dir3/new_weekly_2014_"$el"_200003_5.data $PRIMSEC/. || scp david@$FILERS_LOCATION_2:$dir3/new_weekly_2014_"$el"_200003_5.data $PRIMSEC/. } export -f do_Copy parallel --retries 10 -j 10 do_Copy {} $PRIMARY ::: "${PRIMARY_PARTITION[@]}" & parallel --retries 10 -j 10 do_Copy {} $SECONDARY ::: "${SECONDARY_PARTITION[@]}" & wait echo "All files copied." Problem Statement:- With the above script at some point I am getting this exception - ssh_exchange_identification: Connection closed by remote host ssh_exchange_identification: Connection closed by remote host ssh_exchange_identification: Connection closed by remote host And I guess the error is typically caused by too many ssh/scp starting at the same time. That leads me to believe /etc/ssh/sshd_config:MaxStartups and MaxSessions is set too low. But my question is on which server it is pretty low? machineB and machineC or machineA? And on what machines I need to increase the number? On machineA this is what I can find - root@machineA:/home/david# grep MaxStartups /etc/ssh/sshd_config #MaxStartups 10:30:60 root@machineA:/home/david# grep MaxSessions /etc/ssh/sshd_config And on machineB and machineC this is what I can find - [root@machineB ~]$ grep MaxStartups /etc/ssh/sshd_config #MaxStartups 10 [root@machineB ~]$ grep MaxSessions /etc/ssh/sshd_config #MaxSessions 10

    Read the article

  • Asus WL-520GU conflicting subnet (and/or IP) with 2Wire DSL

    - by Paula
    I have an Asus wireless router: WL-520GU... and an AT&T 2Wire for my DSL connection. When I try to browse anywhere, I just get an odd message from the Asus router (in the common Asus broken-English, bad formatting, and awful spelling): http://postimage.org/image/upxrjflcj I guess it's trying to say: Your Asus Router and your 2Wire have the same subnet mask. (It doesn't say if that's good, or bad... but it sounds like they must be different.) but... But for the "solution" it looks like it's trying to say: Your Asus Router and your 2Wire have the same IP address. My Asus has the defaults: 192.168.1.1 and 255.255.255.0 My 2Wire has: 192.168.1.66 I'm not seeing where the conflict(s) could be. The Asus firmware is v3.0.0.14 . None of these problems occur with the old v3.0.0.8 firmware. Any ideas on how to fix this? (PLEASE don't say to run a totally different DD/Tomato firmware because it's "better". I need to fix THIS 1 problem, not try to convince my company to switch everything to an entirely different set of problems.)

    Read the article

  • need help with automating a CMD java tool which queries alexa AWS using batch

    - by Eli.C
    Hi everyone, I need to get all available info on 600 URLs from "Alexa Web Information Service", I downloaded the java tool and I'm able to run a single query each time with a single switch/Response Group. I would like to ask how to write a batch file that would automate the process? The java tool runs from the CMD with the following: C:\>java UrlInfo (key1) (key2) (URL) (Response Group) UrlInfo - constant key1 - constant key2 -constant URL - variable (I guess I need to use the "(" sign to read from a file) Response Group - variable - (14 total, and I need to run each Response Group on each of the URLs once ) the app returns data in clear text formatted as XML after each query, here is an example: C:\>java UrlInfo (key1) (key2) www.url.com Rank Response: (?xml version="1.0"?) (aws:UrlInfoResponse xmlns:aws="http://alexa.amazonaws.com/doc/2005-10-05/") (aws:Response xmlns:aws="http://awis.amazonaws.com/doc/2005-07-11") (aws:OperationRequest) (aws:RequestId)ec2b6-e8ae-b392(/aws:RequestId) (/aws:OperationRequest) (aws:UrlInfoResult) (aws:Alexa) (aws:TrafficData) (aws:DataUrl type="canonical")url.com/(/aws:DataUrl) (aws:Rank)**472906**(/aws:Rank) (/aws:TrafficData) (/aws:Alexa) (/aws:UrlInfoResult) (aws:ResponseStatus xmlns:aws="http://alexa.amazonaws.com/doc/2005-10-05/") (aws:StatusCode)Success(/aws:StatusCode) (/aws:ResponseStatus) (/aws:Response) (/aws:UrlInfoResponse) Any help would be really appreciated Thanks and regards Eli.C

    Read the article

  • Cannot connect to local network shares when connected to VPN. Error: "the user name could not be found"

    - by Nick G
    I keep finding that on our small company LAN (7 users, 3 servers) that some servers keep becoming "not accessible" for the purposes of file sharing. They display the message "\SERVER is not accessible. You might not have permission to use this network resource. The user name could not be found". But I don't know why "the user name could not be found" as all the machines are on the same domain and the PDC and BDC seem to be behaving OK. EDIT: VPN seems to be the cause: It turns out I can see the server if I use the IP address (\\1.2.3.4\ etc) or the FQ active directory name (eg \server.domainname.local) but not if I use the server name on its own or a mapped network drive originally created from the "short" name. Oddly though, my machine has no issue resolving the server's DNS name as I can ping the machine name OK and it immediately comes back with the IP, however nslookup seems to fail. It seems to be a problem with how Windows looks up machine names when connected to VPNs. When I'm connected to a VPN, windows seems to use the DNS assocated with the VPN and not the one on the domain controller. This behavior to me, seems incorrect as surely that would mean connecting to any VPN would break any ability to lookup local machine names for servers and printers etc. So I guess the real question now is, how can I make my machine still search the local Active Directory DNS (the PDC) even when connected to a VPN? More info in my comments below.

    Read the article

  • Validating signature trust with gpg?

    - by larsks
    We would like to use gpg signatures to verify some aspects of our system configuration management tools. Additionally, we would like to use a "trust" model where individual sysadmin keys are signed with a master signing key, and then our systems trust that master key (and use the "web of trust" to validate signatures by our sysadmins). This gives us a lot of flexibility, such as the ability to easily revoke the trust on a key when someone leaves, but we've run into a problem. While the gpg command will tell you if a key is untrusted, it doesn't appear to return an exit code indicating this fact. For example: # gpg -v < foo.asc Version: GnuPG v1.4.11 (GNU/Linux) gpg: armor header: gpg: original file name='' this is a test gpg: Signature made Fri 22 Jul 2011 11:34:02 AM EDT using RSA key ID ABCD00B0 gpg: using PGP trust model gpg: Good signature from "Testing Key <[email protected]>" gpg: WARNING: This key is not certified with a trusted signature! gpg: There is no indication that the signature belongs to the owner. Primary key fingerprint: ABCD 1234 0527 9D0C 3C4A CAFE BABE DEAD BEEF 00B0 gpg: binary signature, digest algorithm SHA1 The part we care about is this: gpg: WARNING: This key is not certified with a trusted signature! gpg: There is no indication that the signature belongs to the owner. The exit code returned by gpg in this case is 0, despite the trust failure: # echo $? 0 How do we get gpg to fail in the event that something is signed with an untrusted signature? I've seen some suggestions that the gpgv command will return a proper exit code, but unfortunately gpgv doesn't know how to fetch keys from keyservers. I guess we can parse the status output (using --status-fd) from gpg, but is there a better way?

    Read the article

  • mdadm+zfs vs mdadm+lvm

    - by Alex
    This may be a naive question since I'm new to this and I cannot find any results about mdadm+zfs, but after some testing it seems it might work: The use case is a server with RAID6 for some data that is backed-up somewhat infrequently. I think I'm well served by any of ZFS or RAID6. Platform is Linux. Performance is secondary. So the two setups I am considering are: A RAID6 array plus regular LVM and ext4 A RAID6 array plus ZFS (without redundancy). Is this second option that I don't see discussed at all. Why ZFS+RAID6? It's mainly because the inability of ZFS to grow a raidz2 with new disks. You can replace disks with larger ones, I know, but not add another disk. You can accomplish 2-disk redundancy and ZFS disk growth using mdadm as the redundancy layer. Besides that main point (otherwise I could go directly to raidz2 without RAID under it), these are the pros-cons that I see for each option: ZFS has snapshots without preallocated space. LVM requires preallocation (might be no longer true). ZFS has checksumming (very interested in this) and compression (nice bonus). LVM has online filesystem growth (ZFS can do it offline with export/mdadm --grow/import). LVM has encryption (ZFS-on-Linux has not). This is the only major con of this combo I see. I guess I could go RAID6+LVM+ZFS... seems too heavy, or not? So, to close with a proper question: 1) Is there anything that inherently discourages or precludes RAID6+ZFS? Anyone has experience with a setup like this? 2) Are there possibilities for checksumming and compression that would make ZFS unnecessary (maintaining the possibility of filesystem growth)? Because the RAID6+LVM combo seems the sanctioned, tested way.

    Read the article

  • likewise-open and samba as pdc

    - by Knight Samar
    Hi, We have successfully implemented a Samba Primary Domain Controller for a hybrid Windows-Linux environment. So now I am setting up dual-boot clients with Windows XP and Ubuntu 9.10. Windows XP can be easily added to the Samba Domain. Everything is manageable. No worries. But when I try using likewise-open 4.1 to add the Ubuntu 9.10 to the samba domain, it cannot locate the domain controller. domainjoin-cli --loglevel verbose join MYDOMAIN root Error: Unable to resolve DC name [code 0x00080026] Resolving 'MYDOMAIN' failed. Check that the domain name is correctly entered. Also check that your DNS server is reachable, and that your system is configured to use DNS in nsswitch. I even tried mydomain.com variations but to no avail. What am I missing ? I read up a document on MSDN wherein it says that the Domain Controller creates some SRV records in the DNS server. I guess, I don't have them on my BIND. Do you think that is the problem ? If yes, can anyone please point out how and what SRV records need to be added. Thanks.

    Read the article

  • How to restore infrared support in Windows XP?

    - by Emil Rasmussen
    My infrared port is not working on my Windows XP SP 3 (Thinkpad X60). I can see it Device Manager, and it's status is, that it is working probably. The problem manifests in several ways. Originally I was trying to transfer data from my Polar RS800CX watch, and the Polar ProTrainer 5 software gave me the this error message: "Communication port couldn't be opened". Then I tried to connect the watch to another computer, and the infrared connection was established immediately. I then tried to connect the other computer to my Thinkpad X60. The other computer again immediately showed the Wireless Link icon "'computername' is in range" in the notification area. But nothing is shown on the Thinkpad, and a file transfer to the Thinkpad is unsuccessful with an error message that reports that "the target machine actively refused it [the connection]". This brings me to conclude that the infrared support in Windows on the Thinkpad is somehow broken. This is further supported by the fact that I can't find the "Wireless Link" icon in the Control Panel and when I try to run the irprops.cpl nothing happens. So the question is, how to reinstall the infrared support? Some of the solutions that I have explored is: I have tried to disable/enable the infrared in the BIOS - to trick a re-installation. The IR modules settings on the other computer that can get a successful IR connection is an exact match to the ThinkPad that can't get a connection. The was a problem in Windows XP SP 2 with the Wireless Link icon - MS KB article - but that hotfix can't be applied on SP 3 installation. I also guess that the hotfix is included in SP 3. Any other suggestions?

    Read the article

  • How do multiple displays work on a AMD 785G / ATI HD 4200 motherboard?

    - by aireq
    I just ordered a ASUS M4A785TD-V EVO which has the AMD 785G chipset and HD4200 integrated graphic. The board has VGA, DVI, and HDMI outputs. I'm wondering how many outputs I can run at once, and from what connectors? My guess is that I can only use the VGA, and either the DVI or the HDMI in a dual setup. But not the HDMI and the DVI at the same time. Is this correct? If I have devices plugged into both the HDMI and the DVI ports is there a way to choose between which port I want to use? I have a dual 19" monitor setup, as well as a LCD TV. I'd like to run the VGA and the DVI into my two monitors, and then the HDMI to my TV. Then when I want to watch something on the TV I'd like to be able to switch over from the DVI to the HDMI. Is this possible with out crawling under my desk and unplugging/plugging things in? Update I found the following in the manual off ASUS's website, which confirms my original suspicion that HDMI and DVI can't be used at the same time. But I'd still like to know if it's possible through software to switch between using the HDMI and DVI.

    Read the article

  • Has anyone used the sharedband connection bonding product?

    - by John Rennie
    See http://www.sharedband.com/ for details on the product. Obviously Sharedband aren't too keen on giving away their technical secrets, but I would guess that it bonds the connections at the IP layer i.e. their routers send the IP packets to the SharedBand routers over all available lines and the ShareBand routers handle all the virtual circuitry and provide the NATing to whatever IP address(es) they've assigned you. It looks a clever idea, and a good way to provide some resilience over ADSL links. You can even use ADSL links from different ISPs and SharedBand will still bond them for you. But, I find myself wondering how well it really works, and whether it's worth it. The Draytek routers can already load balance (though not bond) up to four ADSL lines, so the SharedBand product really only offers an advantage if you're hosting servers i.e. you can have one IP address to accept incoming connections through all your (working) ADSL lines. But should you really try and host servers using ADSL lines, especially since ADSL upload performance isn't stellar? Wouldn't it be better to use a hosted server, or maybe pay up for a leased line with a SLA? So I'm asking if anyone is using SharedBand, and if so what do you think of it? JR

    Read the article

  • When I log on to my company desktop, I log on to a domain. How is this domain name installed?

    - by learnerforever
    Hi, When I have to work on my machine in company, I have noticed that I log on to a domain (named on the basis of company name) and not really on that computer. From, what I understand, this has a few advantages, the primary being that I just need one password for the domain and can work through any of the machines in company. My questions are : What software on desktop/network have to be installed so that the desktop recognizes and gives me option of logging into a domain. I would guess that a software can be installed on desktop, and there we can configure the IP address of domain server of company and port number, which handles authentication. Is this correct? This takes me to another question that how are softwares installed on end machines in a company. Going to each machine physically and installing looks very unweildy from administrator point of view. An obvious solution would be to install softwares (and updates) over network. My question on this are: What protocols,keywords come into picture when administrator installs OS,softwares,updates from his administrator machine to end machine through network. Thanks,

    Read the article

  • XDEBUG/PHP doesn't dump profile even when set up properly?

    - by John D.
    I installed xdebug from source, but also tried my package manager (separately) and they both are loaded correctly (verified by restarting Apache and seeing the xdebug copyright info in phpinfo()) but they do not dump profiling information. Out of the 40 different attempts of configuration it logged once or twice but I lost what I did, I tried with first only loading the module in php.ini with no settings, but it didn't log to /tmp/. I tried many different settings but my current is now: xdebug.profiler_enable = Off xdebug.profiler_enable_trigger = 1 xdebug.profiler_output_dir = "/tmp/" xdebug.profiler_output_name = "profiler.%t" Of course I call my script through 127.0.0.1/test.php?XDEBUG_PROFILE, which is for enable_trigger. Do you know why it would not dump profiler information? nobody (Arch Linux) can write to /tmp/ as it has before, so I'm sure it is not a permissions error. Apache's error_log does not tell me anything about xdebug either, as it has loaded correctly. It just does not "work"! EDIT: I made a subfolder "xdebug_profiles" in /tmp/ and chown'ed it to nobody, and now it works flawlessly. I'm not sure why it couldn't write before, I guess it's just a caveat with nobody on Arch. I answered my own question , not enough points to answer it or comment, so consider this answered.

    Read the article

  • Is there a simple LDAP-to-HTTP gateway out there?

    - by larsks
    We have a local LDAP directory that provides basic contact information about our user community. We would like to integrate this into some third-party hosted services that allow us to implement widgets that run arbitrary Javascript. In order to connect Javascript to our LDAP directory, I would like to set up a simple LDAP-to-HTTP proxy that would accept HTTP GET requests, translate them into an appropriate LDAP query, and respond with directory information as JSON-encoded data. In an ideal world, something like this: GET /[email protected] Would get me something like this: { "cn": "Bob Person", "title": "System Administrator", "sn": "Person", "mail": "[email protected]", "telepehoneNumber": "617-555-1212", "givenName": "Bob" } (And this obviously assumes that the web application has locally configured information about what base DN to use, how to authenticate, etc). I guess I could write one...but surely something like this already exists? UPDATE The consensus seems to be that there isn't a pre-existing solution out there and that I should just get off my lazy derriere and write one. So I did, and it's here. It's not especially pretty, but it works for my prototyping and I figure maybe someone else will find it useful someday.

    Read the article

  • Any ideas out there as to how the data can be recovered from an SSD?

    - by ben
    A friend had some form of catastrophic failure on an HP mini 1000, unbootable. Of course there was data that wasn't backed up. I've removed the SSD and hooked it up to a ZIF 40 enclosure but can not seem to get the drive to be recognized in Windows 7. In Disk Management it displays as present, but uninitialized. Attempting to initialize it presents an error Virtual Disk Manager - "The device is not ready". There is scant information on MIE (the custom OS), so I'm not even sure what kind of file system I'm dealing with. In any case, if the filesystem is indeed some flavor other than FAT or NTFS, is this error consistent with that? Are there any creative ideas out there as to how the data can be recovered? Update: Thanks for all the suggestions! I hadn't even considered running a live cd. Unfortunately no luck with Ubuntu (live cd) or explore2fs. The zif connection seems ok (color coded green led for proper connect, orange for not). The drive can't be initialized and therefore can't be formatted, so I guess there may be some real damage. Probably needs to head to a specialist. Thanks again for the feedback, much appreciated.

    Read the article

  • Please insert a disk into SD/MMC - Vista problem [closed]

    - by Naunidh
    Possible Duplicate: Please insert a disk into SD/MMC - Vista problem Hi I tried pushing my 2GB micro SD card using the inbuilt card reader. On clicking the drive I get "Please insert a disk into SD/MMC". This problem is really frustrating. The card works fine on other computers so does the microSD to SD attachment. I have done following o fix. - Updated Vista and installed SP1. - Updated the TI drivers for FlashDrive. - Checked Vaio site for updates (none required). - Added a new entry HKLM\SYSTEM\ControlS* et001\Services\tifm21\Parameters/SDParam=1 took the hint from (http://tinyurl.com/nk33tp) I have restarted the PC multiple times. As soon as I put the card in, the SD/MMC device icon blips, so it seems the hardware is at least detecting something. The card reader was working fine few days back. I guess some windows update has broken something, does any one have any idea on how to proceed. MY laptop is VGN-N365E.

    Read the article

  • On a dual-GPU laptop, is using the discrete GPU ever more power efficient?

    - by Mahmoud Al-Qudsi
    Given a laptop with a dual integrated/discrete GPU configuration, is it ever more power efficient to use the discrete GPU instead of the integrated? Obviously when writing an email or working on a spreadsheet, the integrated GPU will always use less power. But let's say you're doing something graphics-medium but not graphics-intensive/heavy - is there a point where it actually makes sense to fire up the discrete GPU, not for performance but for power-saving reasons? Off the top of my head, I can think of a scenario where the external GPU supports hardware decoding of a particular video codec - I'd imagine there is a "price point" where using the GPU saves more energy than decoding that fully in software would. But I think most GPUs, integrated or discrete, pretty much decode just the plain-Jane h264. But maybe there is something more complicated, perhaps if you're doing something like desktop/windowing animations or a flash animation on a website (not an embedded flash video) - maybe the discrete GPU will use enough less power to make up for switching to it? I guess this question can be summed up as to whether or not you can say beyond doubt that if you don't care for performance on a laptop with two GPUs, always use the integrated GPU for maximum battery life.

    Read the article

  • Network connection to Firebird 2.1 became slow after upgrading to Ubuntu 10.04

    - by lyle
    We've got a setup that we're using for different clients : a program connecting to a Firebird server on a local network. So far we mostly used 32bit processors running Ubuntu LTS (recently upgraded to 10.04). Now we introduced servers running on 64bit processors, running Ubuntu 10.04 64bit. Suddenly some queries run slower than they used to. In short: running the query locally works fine on both 64bit and 32bit servers, but when running the same queries over the network the 64bit server is suddenly much slower. We did a few checks with both local and remote connections to both 64bit and 32bit servers, using identical databases and identical queries, running in Flamerobin. Running the query locally takes a negligible amount of time: 0.008s on the 64bit server, 0.014s on the 32bit servers. So the servers themselves are running fine. Running the queries over the network, the 64bit server suddenly needs up to 0.160s to respond, while the 32bit server responds in 0.055s. So the older servers are twice as fast over the network, in spite of the newer servers being twice as fast if run locally. Apart from that the setup is identical. All servers are running the same installation of Ubuntu 10.04, same version of Firebird and so on, the only difference is that some are 64 and some 32bit. Any idea?? I tried to google it, but I couldn't find any complains that Firebird 64bit is slower than Firebird 32bit, except that the Firebird 2.1 change log mentions that there's a new network API which is twice as fast, as soon as the drivers are updated to use it. So I could imagine that the 64bit driver is still using the old API, but that's a bit of a stretch, I guess. Thanx in advance for any replies! :)

    Read the article

  • Xbox360 Universal Media Remote - out of sync?

    - by Traveling Tech Guy
    Hi, I have the Universal Media Remote from Microsoft, which was included with my HD-DVD package. I've been using it for over a year to watch videos/DVDs on my Xbox360 and it saved me the hassle of navigating with the game controller (which turns itself off every 5 minutes).All of a sudden (it didn't fall or suffer any severe trauma), it does not communicate with the Xbox anymore: it is on, I replaced batteries several times, but the Xbox does not respond to commands. The TV does - volume, channels, etc. - but I need the Xbox functionality.As far as I can see, there's no way to sync the remote with the Xbox - it lacks that small sync button that the game controllers have.I called Microsoft Support and spoke for an hour to someone who, I guess didn't know what to do at all. Bottom line - since it's been over a year, they won't fix/replace it - I have to get a new one.Before I do (if I do), I need to know if there's anything I can do with the existing remote, and will I have the same problem with a new one (i.e. the problem is with the Xbox itself)? Thanks!

    Read the article

< Previous Page | 194 195 196 197 198 199 200 201 202 203 204 205  | Next Page >