Search Results

Search found 6945 results on 278 pages for 'azure use cases'.

Page 199/278 | < Previous Page | 195 196 197 198 199 200 201 202 203 204 205 206  | Next Page >

• Debugging Windows PC freeze

  - by Violet Giraffe

  I have a problem with my computer, would appreciate any hints/ideas. It usually begins not immediately after booting Windows, but at some unpredictable point in time, which doesn't seem to correlate with any specific actions of mine. First sign of a problem is process System starting to consume 25% CPU time steadily. I have a quad-core CPU, so it might be one thread working non-stop. At this point micro-freezes start to occur - screen stops refreshing, but if I have, say, music player running - it continues playing. If I try to do something between the freezes, like open Start menu, it will freeze completely and forever. If I press reset button the PC will shut down and then start cold, as opposed to usual reset behavior (which doesn't include PC shutting down). I have noticed that full restart upon reset is usual for hardware problems, but I think this problem isn't related to at least motherboard-CPU-RAM-videoadapter. It certainly isn't caused by overheating. One very important not is that it seems to be related to Windows hosted WLAN network: I have USB Wi-Fi dongle and have configured a hosted network to share cable Internet connection with Wi-Fi devices. I am not 100% certain there's a strong connection, but in 9 or 10 cases when I enabled the network (by executing netsh wlan start hostednetwork), it did freeze eventually (sometimes within minutes of starting the network, sometimes within hours), and on at least 10 days when I didn't start the network it never froze, no matter how I used the computer). There are no critical/error entries in the events log that I can suspect as being related, only regular stuff like "driver not loaded". I have found no critical/error events that are being logged around the time of freeze occurring and are not logged during normal boot without starting the WLAN.

  Read the article

• Problem routing between directly connected Subnets w/ ASA-5510

  - by Zephyr Pellerin

  This is an issue I've been struggling with for quite some time, with a seemingly simple answer (Aren't all IT problems?). And that is the problem of passing traffic between two directly connected subnets with an ASA While I'm aware that best practice is to have Internet - Firewall - Router, in many cases this isn't possible. For example, In have an ASA with two interfaces, named OutsideNetwork (10.19.200.3/24) and InternalNetwork (10.19.4.254/24). You'd expect Outside to be able to get to, say, 10.19.4.1, or at LEAST 10.19.4.254, but pinging the interface gives only bad news. Result of the command: "ping OutsideNetwork 10.19.4.254" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.19.4.254, timeout is 2 seconds: ????? Success rate is 0 percent (0/5) Naturally, you'd assume that you could add a static route, to no avail. [ERROR] route Outsidenetwork 10.19.4.0 255.255.255.0 10.19.4.254 1 Cannot add route, connected route exists At this point, you might gander if its a NAT or Access list problem. access-list Outsidenetwork_access_in extended permit ip any any access-list Internalnetwork_access_in extended permit ip any any There is no dynamic nat (or static nat for that matter), and Unnatted traffic is permitted. When I try pinging the above address (10.19.4.254 from Outsidenetwork), I get this error message from level 0 logging (debugging). Routing failed to locate next hop for icmp from NP Identity Ifc:10.19.200.3/0 to Outsidenetwork:10.19.4.1/0 This led me to set same-security traffic permit, and assigned the same, lesser and greater security numbers between the two interfaces. Am I overlooking something obvious? Is there a command to set static routes that are classified higher than connected routes?

  Read the article

• Is execution of sync(8) still required before shutting down linux?

  - by Amos Shapira

  I still see people recommend use of "sync; sync; sync; sleep 30; halt" incantations when talking about shutting down or rebooting Linux. I've been running Linux since its inception and although this was the recommended procedure in the BSD 4.2/4.3 and SunOS 4 days, I can't recall that I had to do that for at least the last ten years, during which I probably went through shutdown/reboot of Linux maybe thousands of times. I suspect that this is an anachronism since the days that the kernel couldn't unmount and sync the root filesystem and other critical filesystems required even during single-user mode (e.g. /tmp), and therefore it was necessary to tell it explicitly to flush as much data as it can to disk. These days, without finding the relevant code in the kernel source yet (digging through http://lxr.linux.no and google), I suspect that the kernel is smart enough to cleanly unmount even the root filesystem and the filesystem is smart enough to effectively do a sync(2) before unmounting itself during a normal "shutdown"/"reboot"/"poweorff". The "sync; sync; sync" is only necessary in extreme cases where the filesystem won't unmount cleanly (e.g. physical disk failure) or the system is in a state that only forcing a direct reboot(8) will get it out of its freeze (e.g. the load is too high to let it schedule the shutdown command). I also never do the "sync" procedure before unmounting removable devices, and never hit a problem. Another example - Xen allows the DomU to be sent a "shutdown" command from the Dom0, this is considered a "clean shutdown" without anyone having to login and type the magical "sync; sync; sync" first. Am I right or was I lucky for a few thousands of system shutdowns?

  Read the article

• Running $ORIGIN linked binaries from setuid scripts on linux

  - by drscroogemcduck

  I'm using suidperl to run some programs that require root permissions. however, the runtime linker won't expand library paths which contain $ORIGIN entries so the programs i want to run (jstack from java) won't run. more info here There is one exception to the advice to make heavy use of $ORIGIN. The runtime linker will not expand tokens like $ORIGIN for secure (setuid) applications. This should not be a problem in the vast majority of cases. my program looks something like this: #!/usr/bin/perl $ENV{PATH} = "/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin:/usr/java/jdk1.6.0_12/bin:/root/bin"; $ENV{JAVA_HOME} = "/usr/java/jdk1.6.0_12"; open(FILE, '/var/run/kil.pid'); $pid = <FILE>; close(FILE); chomp($pid); if ($pid =~ /^(\d+)/) { $pid = $1; } else { die 'nopid'; } system( "/usr/java/jdk1.6.0_12/bin/jstack", "$pid"); is there any way to fork off a child process in a way so that the linker will work correctly.

  Read the article

• Is it possible to have a conditional formatting cell "visually cycle" through all the formats that evaluated true?

  - by Ben

  Like the title says, "In Excel, when a cell has multiple conditional formatting rules that evaluate true, is it possible to have the cell "visually cycle" through all the formats that evaluated true? If not, suggestions on what to do would be appreciated!" I'm creating an employee schedule for a business that has multiple job areas that need to have an employee assigned to cover. The schedule is currently set up with the date on the top row, employee list down the left column, and the employee's assigned "job area" cross-referencing with the date on the top row. Originally it was set up where if every required "job area" didn't have someone assigned to it, the date would (via conditional formatting) change to red. I've set it up now that if a condition isn't met, the date will change to the color of the "job area" that doesn't have an employee assigned to it. However, there are cases where multiple job areas don't have an employee assigned, but the date will only change color based on the first condition that isn't met. It'd be nice if there was some way for the date cell to cycle through the different colors that correspond to the job areas where no one is assigned. I have a hunch that's not possible though. If it is possible, I'd love to know how to do it. And if it isn't, if anyone has any suggestions on how I can modify the Excel sheet to make it easier to identify the job areas that don't have anyone assigned to them, I would appreciate it. FYI This schedule goes out months in advance.

  Read the article

• What was SPX from the IPX/SPX stack ever used for?

  - by Kumba

  Been trying to learn about older networking protocols a bit, and figured that I would start with IPX/SPX. So I built two MS-DOS virtual machines in VirtualBox, and got IPX communications working (after much trial and error). The idea being to get several old DOS games to run, link up to a multiplayer match, interact with each game window, and capture the traffic using Wireshark from the host machine. From this, I got Quake, Masters of Orion 2, and MechWarrior 2 to communicate back and forth. Doom, Doom2, Duke3d, Warcraft, and several others either buggered up under the VM or just couldn't see the other VM on the IPX network. What did I discover? None of the working games used SPX. Not even Microsoft's NET DIAG used SPX. They all ran ONLY on top of IPX. I can't even find SPX examples or use-cases of SPX traffic running over IEEE 802.3 Ethernet II framing. I did find references that it was in abundant use on token ring, but that's it. Yet any IPX-aware application that I've hunted down so far usually advertises itself as "IPX/SPX", which seems to be a bit of a misnomer, since it doesn't seem to use SPX. So what was SPX used for? Any DOS applications out there that use it which will run under my VM setup? Edit: I am aware that IPX is to SPX as IP is to TCP (layer 3 to layer 4), so I expected to see an SPX layer underneath the IPX layer in Wireshark when I ran my tests.

  Read the article

• Word 2010, Multiple Columns, Vertical center one column only

  - by Nancy N Jones

  I am creating a document with two columns in Microsoft Word 2010. I want the first column to be centered vertically. I want the second column to be on the same page and the vertical placement to be from the top. I highlight my text in the first column that I want centered vertically, then go to Page Layout Margins Custom Margins Layout, you can choose to center the vertical alignment. I have choosen the "Section Start" to be "Column" and also tried "Continuous." In all cases it always shifts all of my second column information to a new page. I don't want my second column text to be on a new page, I want it to be on the same page and vertically aligned from the top--not the center. Am I understanding the functionality of the Section Start on the Layout tab correctly? Maybe the page layout isn't the correct formatting to use. What I am really doing is formatting columns. I haven't found anywhere to format the columns for this. Am I missing some important column formatting features? I know that I can use the paragraph formatting and add space above the first line of text to make it look like it is centered vertically. However, this is a template for a master document and will be changed frequently. I really would like the first column text to be automatically formatted to be centered vertically without having to go in and manually change the space above the paragraph every time. Your assistance would be greatly appreciated.

  Read the article

• What are the frequencies of current in computers' external peripheral cables and internal buses?

  - by Tim

  From Wikipedia, three different cases of current frequency are discussed along with the types of cables that are suitable for them: An Extra Ordinary electrical cables suffice to carry low frequency AC, such as mains power, which reverses direction 100 to 120 times per second (cycling 50 to 60 times per second). However, they cannot be used to carry currents in the radio frequency range or higher, which reverse direction millions to billions of times per second, because the energy tends to radiate off the cable as radio waves, causing power losses. Radio frequency currents also tend to reflect from discontinuities in the cable such as connectors, and travel back down the cable toward the source. These reflections act as bottlenecks, preventing the power from reaching the destination. Transmission lines use specialized construction such as precise conductor dimensions and spacing, and impedance matching, to carry electromagnetic signals with minimal reflections and power losses. Types of transmission line include ladder line, coaxial cable, dielectric slabs, stripline, optical fiber, and waveguides. The higher the frequency, the shorter are the waves in a transmission medium. Transmission lines must be used when the frequency is high enough that the wavelength of the waves begins to approach the length of the cable used. To conduct energy at frequencies above the radio range, such as millimeter waves, infrared, and light, the waves become much smaller than the dimensions of the structures used to guide them, so transmission line techniques become inadequate and the methods of optics are used. I wonder what the frequencies are for the currents in computers' external peripheral cables, such as Ethernet cable, USB cable, and in computers' internal buses? Are the cables also made specially for the frequencies? Thanks!

  Read the article

• Laptop Randomly Turning On and Off

  - by Ian Mallett

  So, I have a pretty new laptop, and one of its quirks is that, at random times (though typically in the middle of the night), it seems to wake up from sleep mode, churn a bit, and then go back into sleep mode. I write "seems" because its fans are very loud, so it's obvious when it's not asleep, but during the time it is "on", I can't see anything on the screen. I have researched the problem somewhat, and could only find similar issues; nothing identical. In those cases, it appeared that certain devices could be responsible. Nothing is plugged into my computer during this behavior, but I nonetheless disabled every device's permission to wake the computer through the device manager. This included disabling the magic packet wake for the network (despite its only having a wireless connection). Using "powercfg /lastwake" gives an empty wake history. But, I also went through all the tasks and checked if they would wake the computer. None appeared to. The problem persisted, so, after some more research, I found this, and executed it for all power schemes on the computer. The problem persists. System: OS: Windows 7 Professional CPU: Intel 990X GPU: NVIDIA GeForce 580M/12GB RAM Motherboard: Clevo X7200 Model: NP7282-S1 (Sager-built laptop)

  Read the article

• Why *do* windows print queues occasionally choke on a print job

  - by Ian

  Y'know they way windows print queues will occasionally stop working with a print job at the head of the queue which just won't print and which you can't delete? Anyone know whats going on when this happens? I've been seeing this since the NT4 days and it still happens on 2008. I'm talking about standard IP connected laser printers - nothing fancy. I support a lot of servers and loads of workstations and see this happen a few times a year. The user will call saying they can't print. When you examine the print queue, which in my case will generally be a server based queue shared out to the workstations, you find a print job which you cannot cancel. You also can't pause it, reinitialize it, nothing. Stopping the spooler is the usual trick and works sometimes. However I occasionally see cases which even this doesn't cure and which a reboot is the only solution. Pause the queue, reboot, when it comes back up the job can then be deleted. Once gone the printer happily goes back to its normal state. No action is ever necessary on the printer. I regard having to reboot as last resort and don't like it. What on earth can be going on when stopping the process (spooler) and restarting it doesn't clear a problem? Its not linked to any manufacturer either. I've seen this on HPs, lexmark, canon, ricoh, on lasers, on plotters.... can't say I ever saw this on dot matrix. Anyone got any ideas as to what may be going on. Ian

  Read the article

• mysql thread count

  - by Ryan M.

  We have a web application that uses apache and mysql. Generally (according to Munin) our MySQL thread count sits between 2 and 4 at all times. The other day, our server almost came to a halt. HTTP requests were slow or wouldn't go through at all, SSH would work, but would take 30+ seconds to register keystrokes, etc.. So we pull up Munin and the only thing that's out of normal boundaries is the Mysql thread count. CPU usage was under 1%, load was under 1.0, plenty of available RAM. As mentioned before, the thread count floats around 2 to 4. At the time of our slow downs it had spiked to 14. So I start poking around the Internet and I see that in most cases, you'll start to see a higher thread count when you start running into slow queries. If I understand it correctly, the request comes in that takes a while to process, in the mean time other requests are coming in, so a new thread will be created to work on the request (yes?). But at the time of the slow down, we had 0 slow queries. My question is: What else can cause mysql to create additional threads. And would this sudden spike in threads possibly cause the server to slow down? To fix the issue, we restarted apache and everything went back to it's beautiful, normal self. Considering the the Server Vitals (CPU, RAM, Network, etc) were all ideal, and the thread count was the only thing out of place, this seems like the most logical thing to pursue as the possible cause. If it matters, we're on Mysql 5.1.40. Server is FreeBSD 7.2 and the server in question is inside a jail.

  Read the article

• Is this "cache administrator" error my server's problem?

  - by Eoin

  Hey, I have a CentOS VPS running Apache with a phpBB installation. One specific user has received errors when posting a message or logging in to the forum. The following issue has arisen in parallel to installing nginx, which serves only the static files of my site. Not sure if this is only coincidence. Furthermore, my setup uses redirects (in some cases, double-redirects) to point the user to a different virtual folder. So, the forum is seen to be at /translation/ but the actual files are found in /phpbb/. I'm at a loss as to what may be the underlying issue. My server? The person's ISP? She has tested both at home and at work, with similar issues. While trying to process the request: GET /phpbb/index.php?sid=f62c927e7eb8f1d60a92dcc6fd918112 HTTP/1.1 Host: www.irishgaelictranslator.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.2.13) Gecko/20101203 Firefox/3.6.13 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-za Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 115 Connection: keep-alive Referer: http://www.irishgaelictranslator.com/phpbb/ucp.php?mode=login Cookie: phpbb3_cipi4_u=96645; phpbb3_cipi4_k=; phpbb3_cipi4_sid=f62c927e7eb8f1d60a92dcc6fd918112; __utma=153470688.1232378553.1294664234.1294664234.1294664234.1; __utmb=153470688.9.10.1294664234; __utmc=153470688; __utmz=153470688.1294664235.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none); style_cookie=null The following error was encountered: Invalid Response The HTTP Response message received from the contacted server could not be understood or was otherwise malformed. Please contact the site operator. Your cache administrator may be able to provide you with more details about the exact nature of the problem if needed.

  Read the article

• How to test/debug bad network wiring?

  - by Jack Lloyd

  I recently bought a place already wired with Cat 5E (8 ports, leading to a central closet). However attempting to get link, nothing works. On closer examination, it was obvious that the ends in the closet were wired backwards (brown on pin 1, etc). The jacks that I've pulled out of the wall do look to be correctly done. However, testing with a network cable tester shows zero link between any of the jacks and any of the ports in the closet - I had expected to just see a 1/8, 2/7, ... 8/1 mismatch, but instead get nothing at all. The runs are accessible and look neat, though they take some bends that seem quite sharp and are in some cases much longer than they need to be (the person who put this in was a professional electrician but I suspect this was the first time he ran network cabling). My best guess at this point is that he either bought bad cable, or put so much tension on it that he snapped wires. Though it seems surprising/unlikely that I wouldn't get at least one active wire on one of the 8 lines. So, my question: is there anything else I should try or test before I go ripping out everything and running new cable?

  Read the article

• Windows Server 2012 Hyper-V very slow

  - by Matt Taylor

  I have been running several Hyper-V VMs on Windows Server 2008 R2 for the past couple of years and enjoying perfectly adequate performance for my testing/development/r&d environments. I'm a software developer so my hardware knowledge is basic however I built the rig using: •Gigabyte GA-X58A-UD3R Intel X58 (Socket 1366) DDR3 Motherboard •Intel Core i7 960 3.20GHz (Bloomfield) (Socket LGA1366) •24GB triple channel RAM The host OS is running on an OCZ SSD and all the VMs are running on a 2TB Marvell SATA3 RAID 0 array consisting of 2 Western Digital Caviar Black 7,200rpm drives. I have tested the speed of the 2TB drive and appear to be getting less than 3Mbs but it can adequately run a 4 VM farm including a DC, (SQL) database and IIS application servers. I recently upgraded the SSD on which the host runs to a 256GB OCZ Vertex 4 and took the opportunity to upgrade to Windows Server 2012 and installed the Hyper-V role. I tried importing one of my existing Windows Server 2008 R2 VMs (and converted it to .vhdx) plus I have tried creating a brand new Windows Server 2008 R2 VM but both are running extremely slowly and I can see nothing obvious using the host and guest Task Manager/Resource Monitor tools. In both cases the VM has 8GB RAM (fixed), 4 CPUs, fixed size HD (not expanding) and is using an external virtual network running on a separate NIC to the host. I have upgraded the BIOS to the latest available version and checked the virtualization settings. I have run out of "obvious" (to a developer) things to check/configure and my next option will be to re-install the host OS but before I do I would very much appreciate any advice from any experts out there. Thanks

  Read the article

• TCP Server Memory management: #Connections Vs. #Requests

  - by Andrew

  Given that, there is no theoretical limit to number of concurrent TCP connections a Windows 2008 server can handle. Only thing will happen is, with each connection there will be memory consumption in server. Unfortunately, memory is not unlimited (and I want to utilize only physical memory). For example, lets say we've 2GB server memory. Now there are two extreme cases: Case 1: If we've allocated 64KB buffer for each connection (only to receive incoming request), then 32768 connections can consume all the 2GB of memory. This will not leave any memory to queue/process incoming requests from those connections. Case 2: On the other hand, lets say a single (or very few) connections continuously keeps sending request buffers (for example, video streaming from one connection to other) and server cannot process them within time, those buffers will get piled up in server and eventually will occupy most of the servers memory. And it will not leave any memory for new connection thereafter. This is the real dilemma in server design bugging me badly for last many days. If I can decide on max size of request buffer per connection and max number of requests to allow in queue per connection. Then, based on available server memory, it will then automatically set limit on max number of concurrent connections. How to decide on these limits to achieve best performance and throughput? I am just looking for perfect utilization of server resources. Are there any standard guidelines or empirical data available with someone who can share with me please.

  Read the article

• CLOSE_WAIT sockets burst - perhaps because of iptables settings?

  - by Fabrizio Giudici

  I have an Ubuntu 12.04 server virtual box where basically the installed software and configuration are the default ones, plus the installation of a jetty 6 server which servers a few websites. To keep things simple I didn't install apache httpd and used iptables for exposing jetty (which runs on the 8080 port) to the port 80. These are the results of /sbin/iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain POSTROUTING (policy ACCEPT) target prot opt source destination I must confess I have a shallow comprehension of how iptables works, in particular for the different kind of chains. This thing works, but sometimes I have an explosion of sockets that stay permanently in CLOSE_WAIT state. I know about what this state means, but since I didn't write the code that manages servlets (they are handled by jetty) I can't fix the problem by patching my code. Eventually the amount of CLOSE_WAIT sockets builds up and makes the server not responsive, so I have to restart jetty. I've looked around for similar problems wth CLOSE_WAIT, and only found cases related to the programmer's code, or problems with Tomcat, not Jetty. I was wondering whether they could be related to a partially broken iptables configuration (the alternative is a bug in Jetty 6, but I first want to exclude other possible causes). Thanks.

  Read the article

• Number of routers in small community lock up and require reboot.

  - by Anthony Hiscox

  I live in a small town which has one primary ISP. Lately I have noticed that a number of wireless routers have been locking up and requiring a reboot before allowing any connections. This has affected two of my routers, my work router, and a few others. In all cases wired continued to function as usual. Often wireless clients can see the SSID but simply won't connect. I can only think of a few possibilities and was hoping someone here might be able to point me in the right direction: Our ISP is well known to be flaky, something they are doing is causing this, what that might be I have no clue it as seems to affect the wireless only. There's a power issue in town, given our remote location and reputation for crap electrical, this seems reasonable. Only one router was plugged in to a UPS, and I'm not sure of the quality. There is some bug in all the different firmware for every one of these routers (all different). That doesn't seem reasonable, unless; it's an unknown (or known) exploit or DoS of some sort being launched by a massive team of ninjas hell bent on forcing us all to be tethered to our walls by ethernet cables or; it's just been a coincidence and I'm just paranoid (this has some weight, I mean read 4 again). Anyone else experience similar issues and have some tips?

  Read the article

• IPC between multiple processes on multiple servers

  - by z8000

  Let's say you have 2 servers each with 8 CPU cores each. The servers each run 8 network services that each host an arbitrary number of long-lived TCP/IP client connections. Clients send messages to the services. The services do something based on the messages, and potentially notify N1 of the clients of state changes. Sure, it sounds like a botnet but it isn't. Consider how IRC works with c2s and s2s connections and s2s message relaying. The servers are in the same data center. The servers can communicate over a private VLAN @1GigE. Messages are < 1KB in size. How would you coordinate which services on which host should receive and relay messages to connected clients for state change messages? There's an infinite number of ways to solve this problem efficiently. AMQP (RabbitMQ, ZeroMQ, etc.) Spread Toolkit N^2 connections between allservices (bad) Heck, even run IRC! ... I'm looking for a solution that: perhaps exploits the fact that there's only a small closed cluster is easy to admin scales well is "dumb" (no weird edge cases) What are your experiences? What do you recommend? Thanks!

  Read the article

• How to manage multiple email addresses on multiple domains in Exchange

  - by CAD bloke

  Using Hosted Exchange Server, mostly because I use an iPhone, webmail & Outlook on 2 laptops. I want to keep everything consistent and unfragmented. Also, I want push notifications. I have 2 domains, a professional one & a personal one. Each domain has about 5 (give or take) email addresses I use for various purposes. Each domain also has a few parked domains (.net, .org, .info) aliased to the .com domain. I would like to keep emails from the 2 domains separated. Do I need an extra mail box, meaning extra expense or can I create another Exchange user on the same mailbox and create an extra account in Outlook? In either case I will have to wait for iOS4 on the iPhone to manage 2 Exchange accounts. Or am I better off just using a set of rules and folders? The aliased domains are another joy to behold entirely. It looks like I will have to add each email address variant individually. Alternatively, I reckon I may just leave the aliased domains at the pop3 host and let Outlook gather those as edge-cases. Surely I can't be the only one making my life this difficult. Anyone out there done this? From the left field - is this (much) easier in gMail? I'm not committed to Exchange (yet). Previously I used Outlook as a pop3 client with a set of filters to direct incoming traffic to folders. This worked with the aliased domains because my host directed all the aliased TLDs to the same mailbox.

  Read the article

• How to determine the root cause of a system lockup on Ubuntu 8.04 LTS?

  - by jdt141

  I'm currently working a project that involves setting up a PC/104 stack and running Ubuntu 8.04 LTS. We need to use the PC/104 stack because its an embedded application - and we're required to use a DeviceNet peripheral card to communicate to other devices. (DeviceNet is just a protocol on top of CAN.) Anyway, the following hardware is on the stack: Kontron MOPSPM104 with a 1GHz Intel Celeron processor ConnectTech FlashDrive/104 4GB Industrial Temp (-40 to +85 C) Woodhead (Molex) PC104DVNIO DeviceNet card A run of the mill 104 power supply The Kontron Board offers two serial ports, one VGA out, and two USB ports. The DeviceNet card is an ISA card. Because of this (per the User's Guide for the Kontron Board), I have manually set the IRQs in the BIOS to be appropriately configured, and turned off ACPI in both the BIOS and passed the appropriate flag in GRUB. I've installed Ubuntu 8.04 desktop, 32 bit. The problem that I'm having is that, from time to time, the entire 104 stack locks up. This only seems to happen in two cases, both of which we're running GNOME. We have a custom application that uses the DeviceNet card, and the system will lock up, or (more frequently) when we're running Firefox and either surfing for some information or trying to test it - typically by streaming video from a IP-camera. The reason I ask this questions is I cannot determine the root cause of this lockup. The IRQs appear to correctly configured in the BIOS and as the Kernel sees them, and nothing is logged to dmesg. If you all could help me determine the root cause of this lockup, I would greatly appreciate it. Thanks.

  Read the article

• Sharepoint AD imported users are becomming sporadically corrupted, causing us to have to create a ne

  - by TrevJen

  Sharepoint 2007 MOSS with AD imported users. All servers are 2008. I have around 50 users, over the past 2 months, I have had a handful of the users suddenly unable to login to Sharepoint. When they login, they either get a blank screen or they are repropmted. These users are using accounts that have been used for many months, sometimes the problem originates with a password change. In all cases, the users account works on every other Active Directory authenticated resource (domain, exchange, LDAP). In the most recent case, last night I was forced deleted a user ("John smith") because of corruption. The orifinal account name was jsmith. I deleted him from active directory, then deleted him from the profile list in Sharepoint Shared Services. I could not find a way to delete him from the Sharepoint user list, but I reran the import after recreating his account (renamed it too just to be sure to "smithj"). At first, this did not wor, the user could still access all other resources but Sharepoint. then, some 30 minutes later it inexplicably started working. This morning, the user changed passwords, which immediatly broke the login on Sharepoint again. I am at a loss on how to troubleshoot this.

  Read the article

• Legal IT documents

  - by TylerShads

  I have been wondering this past week because my big boss told me to start keeping track of all the things I have fixed, how to fix them, etc. Which is reasonable and have been doing anyway. But then a related question came to mind. What kind of documentation should I have on hand as far as users go. More specifically I am talking in terms of EULA, ToC, etc (correct me please if I'm using the wrong terms) Or more specifically a policy, so to speak, for the users and such. Can't say I'm a legal expert, otherwise I'd be a lawyer. The environment the users are in is pretty laid back so I don't forsee a problem. But assume that there should ever arise a problem, what should I have written up/have on hand? EDIT: I really should have noted that we are a medical transport facility and have patient records so I know that something must be done there to comply with HIPAA policies I believe. I do like what anthonysomerset said about the "If I get by a bus" Scenario and want to apply it not only to the documentation I am currently writing but also for if say an employee were to steal info from the server or edge cases, theft, etc. As far as our staff, its relatively small as in a single HR person, no legal department aside from the 2 owners' lawyers and me being the only IT person on staff with a guy who is no more than a mac superuser.

  Read the article

• Use a preferred username but authenticate against Kerberos principal

  - by Jason R. Coombs

  What I desire to do should be pretty simple. I have an Ubuntu 10.04 box. It's currently configured to authenticate users against a kerberos realm (EXAMPLE.ORG). There is only one realm in the krb5.conf file and it is the default realm. [libdefaults] default_realm = EXAMPLE.ORG PAM is configured to use the pam_krb5 module, so if a user account is created on the local machine, and that username matches the [email protected] credential, that user may log in by supplying his kerberos password. What I would like to do instead is create a local user account with a different username, but have it always authenticate against the canonical name in the kerberos server. For example, the kerberos principal is [email protected]. I would like to create the local account preferred.name and somehow configure kerberos that when someone attempts to log in as preferred.name, it uses the principal [email protected]. I have tried using the auth_to_local_names in krb5.conf, but this doesn't seem to do the trick. [realms] EXAMPLE.ORG = { auth_to_local_names = { full.name = preferred.name } I have tried adding [email protected] to ~preferred.name/.k5login. In all cases, when I attempt to log in as preferred.name@host and enter the password for full.name, I get Access denied. I even tried using auth_to_local in krb5.conf, but I couldn't get the syntax right. Is it possible to have a (distinct) local username that for all purposes behaves exactly like a matching username does? If so, how is this done?

  Read the article

• ApplicationPoolIdentity IIS 7.5 to SQL Server 2008 R2 not working.

  - by Jack

  I have a small ASP.NET test script that opens a connection to a SQL Server database on another machine in the domain. It isn't working in all cases. Setup: IIS 7.5 under W2K8R2 trying to connect to a remote SQL Server 2008 R2 instance. All machines are in the same domain. Using the ApplicationPoolIdentity for the web site it fails to connect to the SQL Server with the following: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Data.SqlClient.SqlException: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. However if I switch the Process Model Identity to NETWORK SERVICE or my domain account the database connection is successful. I've granted the \$ access in SQL Server. I am not doing any sort of authentication on the web site, it is just a simple script to open a connection to a database to make sure it works. I have Anonymous Authentication enabled and set to use the Application pool identity. How do I make this work? Why is the ApplicationPoolIdentity trying to use ANONYMOUS LOGON? Better yet, how do I make it stop using the Anonymous logon?

  Read the article

• What's the best / easiest way to combine two mailboxes on Exchange 2007?

  - by jmassey

  I've found this and this(2) (sorry, maximum hyperlink limit for new users is 1, apparently), but they both seem targeted toward much more complex cases than what I'm trying to do, and I just want to make sure I'm not missing some better approach. Here's the scenario: 'Alice' has retired. 'Bob' has taken over Alice's position. Bob was already with the organization in a different but related position, and so they already have their own Exchange account with mail, calendars, etc., that they need to keep. I need to get all of Alice's old mail, calendar entries, etc., merged into Bob's existing stuff. Ideally, I don't want to have all of Alice's stuff in a separate 'recovery' folder that Bob would have to switch back and forth between to look at older stuff; I want it all just merged into Bob's current Inbox / Calendar. I'm assuming (read: hoping) that there's a better way to do this than fiddling with permissions and exporting to and then importing from a .pst. Office version is 2007 for everybody that uses Exchange, if that helps. Exchange is version 8.1. What (preferably step-by-step - I'm new to Exchange) is the best way to do this? I can't imagine this is an uncommon scenario, but my google-fu has failed me; there seems to be nothing on this subject that isn't geared towards far more complex scenarios. (2): h t t p://technet.microsoft.com/en-us/library/bb201751%28EXCHG.80%29.aspx

  Read the article

< Previous Page | 195 196 197 198 199 200 201 202 203 204 205 206  | Next Page >