Search Results

Search found 54080 results on 2164 pages for 'wireless access point'.

Page 2/2164 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• What's wrong with my wireless?

  - by dazzle

  I am having issues with my wireless connection. My connection is constantly disconnecting, then attempting to reconnect, reconnecting momentarily, then disconnecting etc. on times scales that range from seconds to minutes. In the meantime, needless to say I'm having significant packet loss. I'm running Ubuntu 14.04 64bit, updated and upgraded to today. Here is my card and driver: delta@sager:~$ lspci -vq | grep -i wireless -B 1 -A 5 04:00.0 Network controller: Intel Corporation Wireless 7260 (rev 73) Subsystem: Intel Corporation Dual Band Wireless-AC 7260 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at f7d00000 (64-bit, non-prefetchable) [size=8K] Capabilities: Kernel driver in use: iwlwifi Here is my kernel: delta@sager:~$ uname -r 3.13.0-34-generic None of the other machines on my home network are having these issues. Windows Vista is networking without issue for goodness sake ;-) Here is a small clipping from the output of dmesg. As you can see, I am getting a cfg80211 message of some sort over and over again (FYI, I've replaced my MAC address with a series of dashes, so anytime there is a ---------------, that was where the MAC address was: [ 1881.739161] wlan1: authenticate with --------------- [ 1881.741561] wlan1: send auth to --------------- (try 1/3) [ 1881.743440] wlan1: authenticated [ 1881.746027] wlan1: associate with --------------- (try 1/3) [ 1881.749244] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1881.754727] wlan1: associated [ 1881.754827] cfg80211: Calling CRDA for country: US [ 1881.761552] cfg80211: Regulatory domain changed to country: US [ 1881.761559] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1881.761564] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1881.761568] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1881.761571] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761574] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761577] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761580] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1881.761584] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1882.391038] cfg80211: Calling CRDA to update world regulatory domain [ 1882.396254] cfg80211: World regulatory domain updated: [ 1882.396260] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1882.396265] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396268] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396271] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1882.396274] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396277] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.148252] wlan1: authenticate with --------------- [ 1886.150005] wlan1: send auth to --------------- (try 1/3) [ 1886.151807] wlan1: authenticated [ 1886.154847] wlan1: associate with --------------- (try 1/3) [ 1886.158147] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1886.163464] wlan1: associated [ 1886.163520] wlan1: Limiting TX power to 30 (30 - 0) dBm as advertised by --------------- [ 1886.163588] cfg80211: Calling CRDA for country: US [ 1886.170500] cfg80211: Regulatory domain changed to country: US [ 1886.170508] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1886.170513] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1886.170517] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1886.170520] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170523] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170526] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170529] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1886.170533] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1887.200197] cfg80211: Calling CRDA to update world regulatory domain [ 1887.203655] cfg80211: World regulatory domain updated: [ 1887.203659] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1887.203662] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203664] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203666] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1887.203668] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203670] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) I've poked around on AskUbuntu, and have not found any adequate solutions; have also found similar threads that were left unanswered. Any advice/experience/threads I might be able to pull on would be greatly appreciated. In your opinion, is this a kernel issue, hardware issue, etc.? Thanks in advance. EDIT: chili, here's the output of iwconfig: delta@sager:~$ iwconfig wlan1 IEEE 802.11abg ESSID:"LANbeforetime" Mode:Managed Frequency:2.412 GHz Access Point: ----------- Bit Rate=48 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=44/70 Signal level=-66 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:80 Missed beacon:0 eth0 no wireless extensions. lo no wireless extensions.

  Read the article

• Oracle Retail Point-of-Service with Mobile Point-of-Service, Release 13.4.1

  - by Oracle Retail Documentation Team

  Oracle Retail Mobile Point-of-Service was previously released as a standalone product. Oracle Retail Mobile Point-of-Service is now a supported extension of Oracle Retail Point-of-Service, Release 13.4.1. Oracle Retail Mobile Point-of-Service provides support for using a mobile device to perform tasks such as scanning items, applying price adjustments, tendering, and looking up item information. Integration with Oracle Retail Store Inventory Management (SIM) If Oracle Retail Mobile Point-of-Service is implemented with Oracle Retail Store Inventory Management (SIM), the following Oracle Retail Store Inventory Management functionality is supported: Inventory lookup at the current store Inventory lookup at buddy stores Validation of serial numbers Technical Overview The Oracle Retail Mobile Point-of-Service server application runs in a domain on Oracle WebLogic. The server supports the mobile devices in the store. On each mobile device, the Mobile POS application is downloaded and then installed. Highlighted End User Documentation Updates and List of Documents  Oracle Retail Point-of-Service with Mobile Point-of-Service Release NotesA high-level overview is included about the release's functional, technical, and documentation enhancements. In addition, a section has been written that addresses Product Support considerations.   Oracle Retail Mobile Point-of-Service Java API ReferenceJava API documentation for Oracle Retail Mobile Point-of-Service is included as part of the Oracle Retail Mobile Point-of-Service Release 13.4.1 documentation set. Oracle Retail Point-of-Service with Mobile Point-of-Service Installation Guide - Volume 1, Oracle StackA new chapter is included with information on installing the Mobile Point-of-Service server and setting up the Mobile POS application. The installer screens for installing the server are included in a new appendix. Oracle Retail Point-of-Service with Mobile Point-of-Service User GuideA new chapter describes the functionality available on a mobile device and how to use Oracle Retail Mobile Point-of-Service on a mobile device. Oracle Retail POS Suite with Mobile Point-of-Service Configuration GuideThe Configuration Guide is updated to indicate which parameters are used for Oracle Retail Mobile Point-of-Service. Oracle Retail POS Suite with Mobile Point-of-Service Implementation Guide - Volume 5, Mobile Point-of-ServiceThis new Implementation Guide volume contains information for extending and customizing both the Mobile POS application for the mobile device and the Oracle Retail Mobile Point-of-Service server. Oracle Retail POS Suite with Mobile Point-of-Service Licensing InformationThe Licensing Information document is updated with the list of third-party open-source software used by Oracle Retail Mobile Point-of-Service. Oracle Retail POS Suite with Mobile Point-of-Service Security GuideThe Security Guide is updated with information on security for mobile devices. Oracle Retail Enhancements Summary (My Oracle Support Doc ID 1088183.1)This enterprise level document captures the major changes for all the products that are part of releases 13.2, 13.3, and 13.4. The functional, integration, and technical enhancements in the Release Notes for each product are listed in this document.

  Read the article

• Advise on a 240,000 sqft outdoor wireless network

  - by whlspacedude

  I would be very appreciative of some advice in the purchase of equipment to provide a wireless network that covers the entire area of an outdoor arena. The area is rectangular-ish in shape. 400ft wide and 600ft long. It has 6 light towers, 1 on each of the 400 foot ends and 2 on each of the 600 foot ends. I can mount on anything and spend as much money as needed. The needs of the network would be to provide access for, up to 15 wireless HD cameras with audio, and a public-wifi network. Can someone point me in the right direction as far as equipment and antennas ? I can provide any additional information that you may need.

  Read the article

• Wireless not working on desktop with Asus USB-N13 (B1) wireless adapter

  - by user900749

  I am trying to connect my desktop to a wireless network. I have purchased an ASUS USB-N13 B1 adapter. I have followed instructions for installing drivers and disabling conflicting drivers. I have thoroughly searched and could not find a solution. The adapter is recognized and powered on. I have entered the ssid and password information into the wireless network configuration. Other machines can connect to this wireless network, and the machine can connect online via ethernet without issue. Here is the output of some commands which summarize my configuration, and might give some clues : ~$ cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.1 LTS" ~$ uname -a Linux petra 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux ~$ lsusb Bus 001 Device 006: ID 0b05:17ab ASUSTek Computer, Inc. ~$ dmesg [ 1883.823150] wlan0: authenticate with 48:5b:39:e7:25:5e (try 1) [ 1884.020027] wlan0: authenticate with 48:5b:39:e7:25:5e (try 2) [ 1884.220025] wlan0: authenticate with 48:5b:39:e7:25:5e (try 3) [ 1884.420023] wlan0: authentication with 48:5b:39:e7:25:5e timed out Any assistance would be appreciated as I have been trying to get this machine online for several weeks now to no avail. Sincerely, Michael.

  Read the article

• 12.04 WiFi issue on a particular access point

  - by user71706

  I have a WiFi access point that I connect to a PC to share its Internet connection with multiple machines, in a training environment. All the machines with 11.04 connect to this access point with no problem, and can access any server on the Internet. These machines have an Intel Wireless -N 1030 BGN chipset (as reported by lspci). Now, my problem is that I don't manage to connect 12.04 machines to this wireless network. The systems I tried do manage to connect (confirmed by Network Manager), but when I try to access a website like http://kernel.org, the browser shows "Connecting to kernel.org...", but displays a "The connection has timed out" error page. Other symptoms: Name resolution works (for example 'nslookup kernel.org') finds kernel.org's IP address 'ping kernel.org' doesn't work The same 12.04 machines have no problem at all with other wireless networks. So there is probably something weird in my access point (though the 11.04 machines are not impacted). Would you have any suggestions for investigating this issue? Thanks, Michael.

  Read the article

• Trying to understand Wireless N vs Wireless AC

  - by EGHDK

  Whenever a new wireless standard gets approved you expect faster speeds and longer range. From everything that I've read about it, it seems that AC will only transfer over the 5GHz band and up to 3Gbps. Studying the new AC routers on the market, it seems that they will transfer over 5GHz and 2.4GHz. And 5GHz will only transfer at 1.3Gbps. Which isn't what AC is supposed to be. I know there is a difference between what the standard actually says, and what products will actually do, but is there any reason for this? Is there any other main differences between AC and N? I've heard people discussing AC and saying that it's finally "fixing" what N was supposed to fix... what do they mean by that? Any security benefits? I have seen this image online: Will AC really do that? Will that require an AC network card in my laptop for that to actually happen? Lastly, will the router only be able to communicate with AC devices if I have beamforming technology on? I know it's a ton of questions, but most articles online seem to be outdated, and don't provide too much reliability.

  Read the article

• Wireless connection shows up but can't connect to internet with an Intel WiFi Link 5100

  - by Eddy

  I'm using an Asus G50V and I'm completely new to ubuntu. I just installed it and can connect to the internet with a wired connection and through wireless from my windows vista that I installed wubi on, and I can connect to my wireless network, but I can't actually connect to the internet through my wireless network. Thanks in advance. Network controller is an Intel Corporation WiFi Link 5100 according to lspci if that helps Also, the connection somehow started working after I decided to unplug my ethernet cable for the third time and headed upstairs after giving up for the day.. not sure how it happened, but after restarting, the connection stopped working again.. Wifi works on 11.10, but stops working when I upgrade back to 12.04..

  Read the article

• Regular wireless dropouts on new lenovo T440s in Ubuntu 14.04

  - by user290670

  Over the last 24 hours my wireless has dropped out regularly. I've tested to make sure it isn't my router (my phone and everyone in the house isn't having problems using the wifi). This is a brand-new installation of Ubuntu 14.04 and according to uname I'm running kernel 3.13.0-24-generic. Now, my laptop has an Intel 7260AC dual band wireless card and I've read that Ubuntu has been having trouble with these. I notice that at http://www.intel.com/support/wireless/wlan/sb/CS-034398.htm There are some updated drivers for my kernel version. However I have no idea how to update the kernel to use these drivers instead so that I can see if this will fix it. Can anyone help? These dropouts are really annoying. EDIT: Upgrading to 3.14.6 did not help.

  Read the article

• Wireless connectivity Wifi 7260 on Ubuntu 10.04

  - by user292332

  I am trying to install Wireless networking on Dell Latitude E5440 Wifi 7260- Ubuntu 10.04.(Yes I know it is old- see the complication below) I did get the wired connection working but our classrooms are wireless. I have tried to upgrade to version 12 last year but to my horror during the first week of class the nfs mounts did not work for multiple users. I never thought to test for more then one person at at time!! I have not been able to find a fix for the upgrade so I must remain at 10.04. NFS mounts are a must for student home directory access on the servers. All desktops are 10.04 as are the servers. Does anyone have a solution to the wireless problem in version 10.04/ or the nfs mounts solution in version 12. Thank you so much. Val

  Read the article

• My laptop can not access internet after setup bridge with wired NIC and wireless NIC

  - by Victor S

  I setup a bridge using wired NIC and wireless NIC in order to make wireless NIC as a Wi-Fi AP to share wired internet access, after setup successfully, the Wi-Fi AP works as my expectation, but my laptop can not access internet, please give me a hand. Thanks. My hostapd.conf $ cat hostapd.conf interface=wlan0 bridge=br0 driver=nl80211 ssid=myAP hw_mode=g channel=11 dtim_period=1 rts_threshold=2347 fragm_threshold=2346 macaddr_acl=0 auth_algs=3 ieee80211n=0 wpa=3 wpa_passphrase=PassWord wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP Setup steps: $ sudo killall hostapd hostapd: no process found $ sudo hostapd -B hostapd.conf Configuration file: hostapd.conf Using interface wlan0 with hwaddr 00:26:5e:e8:4f:8e and ssid 'myAP' $ sudo brctl addbr br0 device br0 already exists; can't create bridge with the same name $ sudo ifconfig eth0 0.0.0.0 up $ sudo ifconfig wlan0 0.0.0.0 up $ sudo brctl addif br0 eth0 $ sudo brctl addif br0 wlan0 device wlan0 is already a member of a bridge; can't enslave it to bridge br0. $ sudo ifconfig br0 192.168.1.110 netmask 255.255.255.0 $ sudo route add default gw 192.168.1.1

  Read the article

• Hybrid wireless network repeating

  - by Oli

  Summary: I'd like to use two Ubuntu computers to extend/compliment an existing wireless access point. I have a network which currently looks a bit like this: What the diagram doesn't show is the interference caused by our house. It's a wifi-blocking robot sent here from the past. The two wired computers are in areas where the signal is most blocked (not by design, just a happy co-incidence). Both wired computers have fairly good network cards. They're both Ubuntu machines and I would like to turn them into additional base stations. I know I could throw more networking hardware at this (network extenders or cable in additional, pure wireless access points) but I've got two Linux machines sitting in ideal places and I feel like they should be able to help me out. I've tried ad-hoc networks but I need something that is a lot more transparent (eg you can migrate from base to base without a connection dropping); it should look like one network to clients.

  Read the article

• Floating point conversion from Fixed point algorithm

  - by Viks

  Hi, I have an application which is using 24 bit fixed point calculation.I am porting it to a hardware which does support floating point, so for speed optimization I need to convert all fixed point based calculation to floating point based calculation. For this code snippet, It is calculating mantissa for(i=0;i<8207;i++) { // Do n^8/7 calculation and store // it in mantissa and exponent, scaled to // fixed point precision. } So since this calculation, does convert an integer to mantissa and exponent scaled to fixed point precision(23 bit). When I tried converting it to float, by dividing the mantissa part by precision bits and subtracting the exponent part by precision bit, it really does' t work. Please help suggesting a better way of doing it.

  Read the article

• TP-Link TL-WA701N not working good as wireless extender

  - by djechelon

  I bought the device in subject to extend the range of my WPA2/PSK-protected wifi network powered by a TP-Link TL-WR340G device (AP+router). I configured it as follows: Operation mode: Universal Repeater MAC of AP: scanned my SSID and got it Channel width: 20MHz Security options: the same as the parent AP (WPA2/PSK with AES encryption) After configuration inSSIDer shows me two APs beaconing the same SSID at different SNRs (because I was with my laptop close to the extender). After a few hours my tablet, far from the parent AP, stopped working. I found that the scan reported two networks with the same SSID: one WPA-protected and one free at all. This happened very frequently. Rebooting the extender by unplugging it worked but this doesn't last long. Sometimes the extender stops transmitting at all, sometimes it beacons an open network to which nobody can connect (because there is no DHCP). What's wrong with my configuration?

  Read the article

• Performance problem with an Intel Wireless 5100

  - by Piet

  I just installed 12.04 on a HP Elitebook 2530p. The performance with wireless connection to an Eminem 4551 is very bad. Wired connection just works great. If I connect to my router (Eminent 4551) wired I have a good performance accessing internet pages with Firefox. When I try to access the same internet pages wireless I get a real bad performance. piet@piet-HP-EliteBook-2530p:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:03.0 Communication controller: Intel Corporation Mobile 4 Series Chipset MEI Controller (rev 07) 00:03.2 IDE interface: Intel Corporation Mobile 4 Series Chipset PT IDER Controller (rev 07) 00:03.3 Serial controller: Intel Corporation Mobile 4 Series Chipset AMT SOL Redirection (rev 07) 00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 02:00.0 Network controller: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection 44:06.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 44:06.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) piet@piet-HP-EliteBook-2530p:~$

  Read the article

• 12.04 Wi-Fi not working correctly with Intel Pro/Wireless 3945ABG

  - by Jerel

  This is a very strange problem. The only time the Wi-Fi works is when I have the wired connection connected. I have a Dell 6400/e1505 with the Broadcom BCM 4401-B0 internal NIC, and the Intel Pro/Wireless 3945ABG Wi-Fi adapter. I was on 10.0.4 LTS before, and I remember having to screw around to get the Wi-Fi to work, but that was years ago, and now it's acting even stranger than it did back then. If I boot up with the wire connected, the Wi-Fi starts up. If I boot up without the wire connected, the Wi-Fi won't start at all. If after booting with the wire connected, and the Wi-Fi starts up, I then disable the wireless, the wired connection works fine. Without the wire connected, dmesg shows the iwl3945 driver loading and starting with no errors, and the wireless adapter activated. Running rfkill list shows no blocks, but there is no connection to my Wi-Fi. Help! I am more confused than a chameleon in a bag of Skittles.

  Read the article

• Can not connect to wireless on 12.04 with Intel WiFi Link 5100

  - by WiData

  I am having problem in connecting to wifi. I have dual boot (Windows 7 and Ubuntu 12.04) on my Dell Studio 15. I upgraded to 12.04 quite some time ago (at least one month) from 11.10. Everything was working fine till yesterday. Since yesterday I can see the list of available Wifi connection but does not connect to any or if connects (after hours of trying) then disconnects after few minutes. My wifi interface is Intel WiFi Link 5100 AGN. However the problem is on both Windows and Ubuntu. Here are outputs of some commands which may be useful for those interested in helping: ~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:22:19:fa:65:bb UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:794 errors:0 dropped:0 overruns:0 frame:0 TX packets:794 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:56280 (56.2 KB) TX bytes:56280 (56.2 KB) wlan0 Link encap:Ethernet HWaddr 00:22:fb:d2:fc:ce UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:239 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:53603 (53.6 KB) Here is the output for the command sudo lshw -C network *-network description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:22:fb:d2:fc:ce width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-48-generic-pae firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:f8000000-f8001fff My kernel version is kernel version 3.2.0-48-generic-pae I also checked this post which was helpful. But I am not sure if what is the exact problem. Any suggestions will be helpful. Should I be changing the firmware/driver? Currently my /lib/firmware has following iwlwifi files /lib/firmware/iwlwifi-1000-5.ucode /lib/firmware/iwlwifi-5000-5.ucode /lib/firmware/iwlwifi-100-5.ucode /lib/firmware/iwlwifi-5150-2.ucode /lib/firmware/iwlwifi-105-6.ucode /lib/firmware/iwlwifi-6000-4.ucode /lib/firmware/iwlwifi-135-6.ucode /lib/firmware/iwlwifi-6000g2a-5.ucode /lib/firmware/iwlwifi-2000-6.ucode /lib/firmware/iwlwifi-6000g2a-6.ucode /lib/firmware/iwlwifi-2030-6.ucode /lib/firmware/iwlwifi-6000g2b-6.ucode /lib/firmware/iwlwifi-3945-2.ucode /lib/firmware/iwlwifi-6050-5.ucode /lib/firmware/iwlwifi-4965-2.ucode Thanks a lot for the help.

  Read the article

• Atheros AR2413 wireless not working after shutdown

  - by Chandrasekhar

  I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

  Read the article

• Wireless will not work in fresh ubuntu 12.04 lts installation

  - by Taake Manning

  I did a fresh Ubuntu 12.04 install on my Sony Vaio laptop, which worked perfectly with 10.04. Now my wireless won't work. I have read just about every Q&A on the subject and I have tried different solutions, including the official troubleshooting guides. My laptop is equipped with a Intel 5100 wireless device. Ubuntu recognizes the device and it's status is given as connected in nm-tool. I can ping the gateway, my own IP number and localhost. Rfkill shows no soft or hard blocks. Any ideas? I am just a few hours shy of reinstalling good old 10.04! Taake

  Read the article

• Script to setup Ubuntu as a wireless access point on a bridge mode

  - by nixnotwin

  I use the following script to make my netbook a full-fledged wireless access point. It creates a bridge with eth0 and wlan0 and starts hostapd. #!/bin/bash service network-manager stop ifconfig eth0 0.0.0.0 #remove IP from eth0 ifconfig eth0 up #ensure the interface is up ifconfig wlan0 0.0.0.0 #remove IP from eth1 ifconfig wlan0 up #ensure the interface is up brctl addbr br0 #create br0 node hostapd -d /etc/hostapd/hostapd.conf > /var/log/hostapd.log & sleep 5 brctl addif br0 eth0 #add eth0 to bridge br0 brctl addif br0 wlan0 #add wlan0 to bridge br0 ifconfig br0 192.168.1.15 netmask 255.255.255.0 #ip for bridge ifconfig br0 up #bring up interface route add default gw 192.168.1.1 # gateway This script works efficiently. But if I want to revert back to use Network Manager, I cannot do it. The bridge simply cannot be deleted. How can I modify this script so that if I run bridge_script --stop, the bridge gets deleted, network manager starts and interfaces behave as if the machine had a fresh reboot.

  Read the article

• Script to setup ubuntu as a wireless accesspoint on a bridge mode

  - by nixnotwin

  I use the following script to make my netbook a full-fledged wireless accesspoint. It creates a bridge with eth0 and wlan0 and starts hostapd. #!/bin/bash service network-manager stop ifconfig eth0 0.0.0.0 #remove IP from eth0 ifconfig eth0 up #ensure the interface is up ifconfig wlan0 0.0.0.0 #remove IP from eth1 ifconfig wlan0 up #ensure the interface is up brctl addbr br0 #create br0 node hostapd -d /etc/hostapd/hostapd.conf > /var/log/hostapd.log & sleep 5 brctl addif br0 eth0 #add eth0 to bridge br0 brctl addif br0 wlan0 #add wlan0 to bridge br0 ifconfig br0 192.168.1.15 netmask 255.255.255.0 #ip for bridge ifconfig br0 up #bring up interface route add default gw 192.168.1.1 # gateway This script works efficiently. But if I want to revert back to use Network Manager, I cannot do it. The bridge simply cannot be deleted. How can I modify this script so that if I run bridge_script --stop, the bridge gets deleted, network manager starts and interfaces behave as if the machine had a fresh reboot.

  Read the article

• Ubuntu 12.04, Intel Centrino 1030 Wireless-N 1030 not able to connect to wireless

  - by playcat

  I saw several similar threads, but none really does it... I have 12.04 precise x64 installed and things worked great for some 10 days. Then it all stopped - I wasn't able to connect any more. Even more, things were so scre*ed up that it were showing other network's name while connecting :( I have an Asus K53SM-SX054. Here's the text from dmesg related to my card: http://fixee.org/paste/iaw23iw/ Basically, it's Intel Centrino Wireless-N 1030. Not sure if it's important, I had Gnome with unity and then moved to KDE. Any ideas what to do? I'm on the verge of reinstalling things, but I already set plenty of things and have some things that I'd need to back up... and I'm rather lazy to go on with it :) EDIT: My wlan network is hidden. Not sure if this should have any influence.

  Read the article

• Wireless connection keeps losing connection

  - by Santiago

  I'm having this annoying problem with my Ubuntu 12.04.1, upgraded from 10.04. The thing is that my wireless connection keeps going out of connection every 15-20 minutes, and sometimes I have to reboot my laptop. I've started having this problem about 1 month ago, but back in my 10.04 I had the same problem. If anyone has any idea it would be great. Also any info you need about the laptop, please tell me the commands I need to run to give it to you. Thanks and hope you help me.

  Read the article

• Cannot enable wireless on an Intel WifiLink 1000 on an Lenovo Ideapad z570

  - by Brij

  I am using the ubuntu 11.10 on lenovo ideapad z570. My wireless internet is not working. I have ensure that wireless switch is on. Windows 7, wireless works great.However ubuntu 11.10 is not allowing me to enable wireless connection. I have run the following command and here is the status. sudo lshw -class network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:1c:a4:a4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:42 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: f0:de:f1:64:b6:62 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff Here is rfkill list all output: rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no Note : Windows 7, wireless card property shows that Intel WifiLink 1000 BGN. Could someone help me to fix this issue.

  Read the article

• Ubuntu 12.04 patched b43 driver compilation error

  - by Zed

  I tried this How do I install this patched b43 driver? guide to install patched b43 driver on Ubuntu 12.04 with 3.2.0-31-generic kernel but I can't pass compilation phase.Here is what I did: wget http://www.orbit-lab.org/kernel/compat-wireless-3-stable/v3.1/compat-wireless-3.1.1-1.tar.bz2 cd compat-wireless-3.1.1-1/ scripts/driver-select b43 make make -C /lib/modules/3.2.0-31-generic/build M=/home/marco/compat-wireless-3.1.1-1 modules make[1]: Entering directory `/usr/src/linux-headers-3.2.0-31-generic' CC [M] /home/marco/compat-wireless-3.1.1-1/compat/main.o In file included from /home/marco/compat-wireless-3.1.1-1/include/linux/compat-2.6.29.h:5:0, from /home/marco/compat-wireless-3.1.1-1/include/linux/compat-2.6.h:24, from <command-line>:0: include/linux/netdevice.h:1153:5: warning: "IS_ENABLED" is not defined [-Wundef] include/linux/netdevice.h:1153:15: error: missing binary operator before token "(" include/linux/netdevice.h: In function ‘netdev_uses_dsa_tags’: include/linux/netdevice.h:1421:9: error: ‘struct net_device’ has no member named ‘dsa_ptr’ include/linux/netdevice.h:1422:31: error: ‘struct net_device’ has no member named ‘dsa_ptr’ include/linux/netdevice.h: In function ‘netdev_uses_trailer_tags’: include/linux/netdevice.h:1431:9: error: ‘struct net_device’ has no member named ‘dsa_ptr’ include/linux/netdevice.h:1432:35: error: ‘struct net_device’ has no member named ‘dsa_ptr’ make[3]: *** [/home/marco/compat-wireless-3.1.1-1/compat/main.o] Error 1 make[2]: *** [/home/marco/compat-wireless-3.1.1-1/compat] Error 2 make[1]: *** [_module_/home/marco/compat-wireless-3.1.1-1] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.2.0-31-generic' make: *** [modules] Error 2 To fix that error I added #include <linux/kconfig.h> to /usr/src/linux-headers-3.2.0-31-generic/include/linux/netdevice.h but now I'm getting something else make make -C /lib/modules/3.2.0-31-generic/build M=/home/marco/compat-wireless-3.1.1-1 modules make[1]: Entering directory `/usr/src/linux-headers-3.2.0-31-generic' CC [M] /home/marco/compat-wireless-3.1.1-1/compat/main.o LD [M] /home/marco/compat-wireless-3.1.1-1/compat/compat.o CC [M] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.o In file included from /home/marco/compat-wireless-3.1.1-1/include/linux/bcma/bcma.h:9:0, from /home/marco/compat-wireless-3.1.1-1/drivers/bcma/bcma_private.h:8, from /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:8: /home/marco/compat-wireless-3.1.1-1/include/linux/ssb/ssb.h: In function ‘ssb_driver_register’: /home/marco/compat-wireless-3.1.1-1/include/linux/ssb/ssb.h:236:36: error: ‘THIS_MODULE’ undeclared (first use in this function) /home/marco/compat-wireless-3.1.1-1/include/linux/ssb/ssb.h:236:36: note: each undeclared identifier is reported only once for each function it appears in In file included from /home/marco/compat-wireless-3.1.1-1/drivers/bcma/bcma_private.h:8:0, from /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:8: /home/marco/compat-wireless-3.1.1-1/include/linux/bcma/bcma.h: In function ‘bcma_driver_register’: /home/marco/compat-wireless-3.1.1-1/include/linux/bcma/bcma.h:170:37: error: ‘THIS_MODULE’ undeclared (first use in this function) /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c: At top level: /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:12:20: error: expected declaration specifiers or ‘...’ before string constant /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:13:16: error: expected declaration specifiers or ‘...’ before string constant /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:182:1: warning: data definition has no type or storage class [enabled by default] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:182:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’ [-Wimplicit-int] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:182:1: warning: parameter names (without types) in function declaration [enabled by default] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:188:1: warning: data definition has no type or storage class [enabled by default] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:188:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’ [-Wimplicit-int] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:188:1: warning: parameter names (without types) in function declaration [enabled by default] make[3]: *** [/home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.o] Error 1 make[2]: *** [/home/marco/compat-wireless-3.1.1-1/drivers/bcma] Error 2 make[1]: *** [_module_/home/marco/compat-wireless-3.1.1-1] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.2.0-31-generic' make: *** [modules] Error 2 Any suggestion what to try next?

  Read the article

• Intel Centrino Wireless-N 1000 Again ! Ubuntu 13.04 x64

  - by vafa

  First I have to say that I tried everything written about this concept. The problem is that it stops working randomly in 3 main forms : 1 - sometimes it disconnect from wireless network and reconnect automatically 2 - sometimes it disconnect and wont connect no matter what (needs reboot) 3 - some times it's still connected but cannot ping or surf or whatever. I already tried disabling N mod using these commands : sudo modprobe -r iwlwifi modprobe iwlwifi 11n_disable=1 (or 0, whatever) it didn't help . these are the results of lspci, sudo lshw -C network, ifconfig, iwconfig, rfkill list when it disconnected and didn't connect till reboot : ifconfig : eth0 Link encap:Ethernet HWaddr c8:0a:a9:34:65:77 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1563213476557380 errors:9379306629148050 dropped:3126435543049350 overruns:1563217771524675 frame:7816088857623375 TX packets:1563217771524675 errors:6252871086098700 dropped:0 overruns:1563217771524675 carrier:3126435543049350 collisions:7816088857623375 txqueuelen:1000 RX bytes:1563217771524675 (1.5 PB) TX bytes:1563217771524675 (1.5 PB) ham0 Link encap:Ethernet HWaddr 7a:79:19:a5:e4:93 inet addr:25.165.228.147 Bcast:25.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:19ff:fea5:e493/64 Scope:Link inet6 addr: 2620:9b::19a5:e493/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:7743 errors:0 dropped:0 overruns:0 frame:0 TX packets:1250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:665642 (665.6 KB) TX bytes:204056 (204.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:41138 errors:0 dropped:0 overruns:0 frame:0 TX packets:41138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6420962 (6.4 MB) TX bytes:6420962 (6.4 MB) wlan0 Link encap:Ethernet HWaddr 00:1e:64:45:fb:70 inet6 addr: fe80::21e:64ff:fe45:fb70/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:286999 errors:0 dropped:0 overruns:0 frame:0 TX packets:226966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:324386887 (324.3 MB) TX bytes:30674804 (30.6 MB) iwconfig : ham0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off sudo lshw -C network: *-network description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:45:fb:70 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-30-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:46 memory:c0400000-c0401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: c0 serial: c8:0a:a9:34:65:77 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:c0900000-c093ffff ioport:5000(size=128) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:19:a5:e4:93 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full ip=25.165.228.147 link=yes multicast=yes port=twisted pair speed=10Mbit/s lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 105M] (rev a1) 07:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak] 09:00.0 Ethernet controller: Qualcomm Atheros AR8131 Gigabit Ethernet (rev c0) rfkill list : 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 9: phy0: Wireless LAN Soft blocked: no Hard blocked: no any help will be REALLLYYYY appreciated

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >