Search Results

Search found 54080 results on 2164 pages for 'wireless access point'.

Page 5/2164 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Wireless not working on Dell XPS 17 after installing 12.04

  - by user60622

  I (linux newbie) have a Dell XPS 17 and tried to install Ubuntu 12.04. After installation all WLAN accesspoints near are detected. But I can not connect (but I am able to connect with other computers as well as with Dell XPS 17 under windows). Outputs: iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:"LerchenPoint" Mode:Managed Frequency:2.412 GHz Access Point: 58:6D:8F:A0:2D:58 Bit Rate=1 Mb/s Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-37 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:19 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:99:98:28 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-24-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:50 memory:f0400000-f0401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:0a:00.0 logical name: eth0 version: 06 serial: f0:4d:a2:56:e3:94 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.123 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:47 ioport:6000(size=256) memory:f0a04000-f0a04fff memory:f0a00000-f0a03fff dmesg | grep iwl [ 10.157531] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 10.157561] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 10.157598] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 10.157599] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 10.157601] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 10.157731] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 10.157834] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 10.157976] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 10.179772] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 10.179775] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 10.179777] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 10.179796] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 10.574728] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 10.726409] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 19.714132] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 19.777862] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2251.603089] iwlwifi 0000:04:00.0: PCI INT A disabled [ 2266.578350] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2266.578399] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 2266.578435] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 2266.578437] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 2266.578439] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 2266.578704] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 2266.578808] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 2266.578916] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.600709] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 2266.600712] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 2266.600713] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 2266.600727] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 2266.605978] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 2266.606331] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 2266.614179] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.681541] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S Solutions I tried: rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. rmmod /lib/modules/3.2.0-24-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/wireless/cfg80211.ko sudo modprobe iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. replacing iwlwifi-1000-5.ucode (current driver) against iwlwifi-1000-3.ucode sudo jockey-gtk: (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed nothing is listet in "Additional drivers" (german: "Zusätzliche Treiber"). gksudo gedit /etc/modprobe.d/blacklist.conf add "blacklist acer_wmi" Any help would be appreciated very much. Thanks!!

  Read the article

• windows 7 wireless knocks off other computers on the network

  - by Sean

  I am trying to fix a wireless network issue. When a new windows 7 machine (we have 2 in the house) we have problems with any other windows xp machines connecting to the wireless network. I am using a linksys WRT110 running Firmware Version: 1.0.04 (which is not the latest firmware its Ver.1.0.07 but the router would not use the bin update file). I have tried a ton of variations in setting for the wireless network, changed the channel, the security level (none, wep wpa, wpa2), network type (g,bg mixed). I have also read some stuff about homegroup settings for windows 7 but have not seen any differences that make a difference. Basically windows 7 does not like to connect to our network but when I manage to get it to work the windows xp pro machines get kicked off. The windows xp pro machines are a few years old but both windows 7 machines are less than 6 months old.

  Read the article

• Obtaining a world point from a screen point with an orthographic projection

  - by vargonian

  I assumed this was a straightforward problem but it has been plaguing me for days. I am creating a 2D game with an orthographic camera. I am using a 3D camera rather than just hacking it because I want to support rotating, panning, and zooming. Unfortunately the math overwhelms me when I'm trying to figure out how to determine if a clicked point intersects a bounds (let's say rectangular) in the game. I was under the impression that I could simply transform the screen point (the clicked point) by the inverse of the camera's View * Projection matrix to obtain the world coordinates of the clicked point. Unfortunately this is not the case at all; I get some point that seems to be in some completely different coordinate system. So then as a sanity check I tried taking an arbitrary world point and transforming it by the camera's View*Projection matrices. Surely this should get me the corresponding screen point, but even that didn't work, and it is quickly shattering any illusion I had that I understood 3D coordinate systems and the math involved. So, if I could form this into a question: How would I use my camera's state information (view and projection matrices, for instance) to transform a world point to a screen point, and vice versa? I hope the problem will be simpler since I'm using an orthographic camera and can make several assumptions from that. I very much appreciate any help. If it makes a difference, I'm using XNA Game Studio.

  Read the article

• My wireless is hard-blocked

  - by Cristian

  I'm new to linux and i am having trouble getting my wireless to work I've found the following things Wireless LAN Soft blocked: no Hard blocked: yes and : *-network DISABLED description: Wireless interface product: RT3090 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 6c:62:6d:19:38:b9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.2.0-25-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:fdfe0000-fdfefff Can you please tell me what to do?

  Read the article

• Suggestions for wireless adapter

  - by Michael Kniskern

  I recently purchased a desktop computer and it did not come with a wireless network card. I am currently using the Belkin Wireless G USB Adapter and it is a very sub par product. It has very slow response times and download speeds with just basic browsing and downloads podcasts through iTunes. Does anyone have a better suggestion for a wireless adapter? Should I go with another USB adapter or one that connects directly into the motherboard? I am current using Windows Vista 64 bit Home Premium.

  Read the article

• Wireless internet sharing stops working after client disconnects

  - by Mandy

  I'm running Unbuntu 11.10 with the latest service packs, sharing an ether connection over wireless. Everything works fine, up to the point that the client (a laptop) sleeps or otherwise disconnects. The wireless connection at that point no longer functions, not showing up when searching for the hotspot with the laptop. The only way to recover is to reboot the machine, or toggle the wireless share off/on. I've double checked the wireless card has power management off. Currently what I'm doing is keeping an Ipod plugged into the box 24/7 to keep the wireless connection up when the laptop disconnects. I've searched the internet far and wide, found many issues with wireless problems after an ubuntu box itself sleeps, but nothing directly related to my problem. Hoping someone has some idea of where to look and what to check. A girl needs her Ipod back!

  Read the article

• Wireless does not work anymore after software update with Ubuntu 12.10 on a Dell Latitude E6230

  - by Andy

  I just installed Ubuntu 12.10 on my DELL Latitude E6230, on first boot wifi worked properly but when I updated the software it stopped working. I can't figure out the problem... The wireless network controller is a Broadcom Corporation BCM4313 802.11b/g/n Wireless Lan Controller (rev 01) "lshw -class network" gives, for the above controller: *-network UNCLAIMED description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7d00000-f7d03fff After reading the answer to another similar question, I edited the file NetworkManager.conf to make "managed=true", but that did not make any difference, it is as if the wireless adapter were not there. In the "Network" setting window, I only see "Wired" and "Network proxy". Wireless has just disappeared: rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no and that's it! Nothing about the wireless controller... Any suggestions?

  Read the article

• Can't find a wireless access point's IP address after changing router IP/LAN settings

  - by flagg19

  I have a modem/router, Netgear DG834, and a wireless access point (AP), Netgear WG602. The AP is directly connected to the router. My old working configuration was: Router IP address : 192.168.0.1 Access point IP address: 192.168.0.10 My new configuration is: Router IP address : 192.168.1.1 Access point IP address: ???.???.???.??? I changed my router's IP address/LAN settings to set up a VPN with another Netgear router that had the same LAN configuration. The wireless network is still up and perfectly working, but I can't find the AP's IP address. I've tried broadcast ping but the AP won't respond. I looked at the router "attached devices", but it's not there. I've played around with Nmap and arp request but the AP is totally invisible. I can fix it by resetting it to factory settings, but I'm very interested in learning more about this problem. I'm also interested in network security and this fact of having an invisible AP well, it's something I'd like to understand.

  Read the article

• Atheros AR5BWB222 Wireless Intermittent Connectivity

  - by Bart

  So I recently installed Ubuntu on my Acer Aspire V3-551 laptop. I have an Atheros AR5BWB222 wireless adapter. Everything works fine except for the wireless. I can sometimes connect to the wireless, but most of the time it will be making an attempt to connect and then enver connect. Or it will connect, but it will only stay connected for about 10 seconds before getting disconnected from the wireless. All the other drivers updated through System SettingsAdditional Drivers are fine, even the Ethernet. Its just the problem with the wireless. I've tried a power managment setting, tried looking for additional updates, but nothing fixes my problem. Is there any solution for my particular wireless card?

  Read the article

• Wireless problems on HP

  - by Sat93

  I'm not able to enable Wireless using the hardware switch on my HP ProBook4430s. Because of this the Enable Wireless option is greyd out and I cannot enable it. The greyd out option can be seen in the screenshot below. The results of iwconfig for my system are as follows, lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. Also I tried to do the following, sudo ifconfig wlan0 up but I got an error as below, SIOCSIFFLAGS: Operation not possible due to RF-kill Also the result of sudo rfkill list all for my system is as follows, 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 3: hci0: Bluetooth Soft blocked: no Hard blocked: no How do I fix this problem? Thanku!

  Read the article

• Programtically get the Wireless lan config of a machine and use netsh to setup new profile

  - by Maestro1024

  Programtically get the Wireless lan config of a machine and use netsh to setup new profile I am having trouble getting the netsh command to set the ssid of a new card. I installed the drivers and plugged it in. I see in ipconfig it says the "media is disconnected" (fair enough). I then send the following command netsh wlan connect name=profile1 ssid=myNetwork interface="Wireless Network Connection 2" problem is I get an error "There is no profile "profile1" assigned to the specified interface. What is a profile for a wireless card? What should I set it to? How Can I get my SSID set and connected for the card.

  Read the article

• D-Link DWA-125 Wireless network card not working after upgrade from 10.04 to 12.04

  - by dava2788

  I upgraded to Ubuntu 12.04 and now the wireless network card D-Link DWA-125 doesn't work. I have the drivers from the official website, But neither recognized during installation. iwconfig: lo no wireless extensions. vmnet8 no wireless extensions. ra0 Ralink STA Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. vmnet1 no wireless extensions. dava@Dava-Ubuntu:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 006: ID 07d1:3c0d D-Link System DWA-125 Wireless N 150 Adapter(rev.A1) [Ralink RT3070] And the chipset: ralink 2870/3070 (rt3070)

  Read the article

• cannot connect to wireless network on ubuntu 12.04

  - by angjinhang

  i have installed ubuntu on my 6-year-old Acer Aspire 4310 and i love it's lightning speed.but, now i have a big problem, that is it cannot connect to any wireless network. the wireless network worked well in my windows. the wireless switch is not responding to me(i guess it only works on windows). there are also no wireless toggle switch on my keyboard. i have installed my driver, yeah, a proprietary driver. i installed it, and my i never see my wireless network anymore, even the enabling and disabling button in the system settings. i can connect my wireless network during the ubuntu installation. so what's the problem? i cannot find wlan0 in the ifconfig output. i can still see the enable and disable button in the system settings before i install the driver. now even i remove the driver, i will no longer display. i wanted my wifi back, help!

  Read the article

• No wireless adapter in msi u200

  - by Mino Marimat

  I have a MSi u200, and the weird thing was that I was using this normally before, then after a few minutes all of a sudden it couldn't find the wifi signal from my house. I did some troubleshooting and a bit of search in the control panel, and it seems like my hardware is missing. :( I can't even turn on the wireless light using Fn+F8, so my suspicions about the missing hardware strengthened. I tried searching for DIY fixes, but I found out that the wireless card is actually built-in deeper, unlike the RAM cards and the hard drive where you can either replace or add more cards. What do I do?? As of the moment, I can get connected to my wifi here at home using a wireless adapter via usb, and it's working. So my guess about the hardware problem seems correct. HELP!!! Thanks!

  Read the article

• forwarding packets from wireless nic wlan0 to another Wireless nic wlan1

  - by user179759

  I have two wireless interfaces wlan0, wlan1 I want wlan0 to be connected to the internet via a wireless router and I want wlan1 to be in AP mode acting as a router to give internet access to whoever connectes to it. So basically all packets coming through wlan1 should be forwarded to wlan0 = Router = Internet. That's including DNS/DHCP/etc.. [A]~~~~~(Wi-Fi)~~~~~~v [B]~~~~~(Wi-Fi)~~~> [me] ~~~~(Wi-Fi)~~~~~>[AP/Router]------->[internet] [C]~~~~~(Wi-Fi)~~~~~~^ Any idea how can I do this? ps: I tried using bridges but I always get 'operation not supported' using the brctl tool.

  Read the article

• how to connect only ethernet and only wireless hosts together

  - by Ashok Das

  Here is my problem. I have an android tablet that have only WiFi for network connectivity and I have a windows server that have only Ethernet ports for network connection. Now I want to telnet to my server from my tablet. I think some wireless to Ethernet converter required in between. I am planning to use Buffalo Air Station WCR-GN or TP-LINK TL-WR740N or TL-WR702N. The connection setup should be like this: [server]<---Ethernet---[WIFI router]<---wireless---[Tablet]. Now I am in doubt will this setup work? Anybody please help me with this. Regards Ashok

  Read the article

• Aruba Wireless Controller 200 and AP70 manual

  - by techie

  I have an Aruba wireless system that is currently in use but there is no documentation from the previous person in charge. I have no manuals or login information for the wireless controllers and APs. I checked the Aruba website and you need to register to access the support information but registration isn't instant and takes several days. I've waited for quite a while now and have tried googling and checking the Aruba forums but have found no indication of a manual. What I really need is the ability to reset the controller and APs so I can access the device with the default username and password. There is no reset button on this device so I have no idea how you go about resetting the controller and APs. Hm it seems I can't create a new tag as a new user. If possible can someone add an "Aruba" tag?

  Read the article

• Aruba Wireless Controller 200 and AP70 manual

  - by techie

  I have an Aruba wireless system that is currently in use but there is no documentation from the previous person in charge. I have no manuals or login information for the wireless controllers and APs. I checked the Aruba website and you need to register to access the support information but registration isn't instant and takes several days. I've waited for quite a while now and have tried googling and checking the Aruba forums but have found no indication of a manual. What I really need is the ability to reset the controller and APs so I can access the device with the default username and password. There is no reset button on this device so I have no idea how you go about resetting the controller and APs. Hm it seems I can't create a new tag as a new user. If possible can someone add an "Aruba" tag?

  Read the article

• Wireless router not connection -> AP Not associated

  - by candido

  I can not connect to internet by wireless router after some months with ubuntu 10.04. I can connect with the same portable but with win OS. My SO is ubuntu 10.04 linux 2.6.32-41 arch SMP i686. The internet wireless network controller is Atheros AR9285 chipset (pci express) Kernel module ath9k I have tried a command line connection: $ sudo /etc/init.d/network-manager stop #stop gui network manager $ iwconfig wlan0 essid WLAN_3C key s:C001D20550B3C $ ifconfig Access Point: NOT-ASSOCIATED $dmesg ... AP 00:1a:2b:08:60:49 associated Is the SO has connected to router for booting long ( associated message), after boot and login why the connection to router is not possible by network-manager or command line (NOT associated message)? Thanks in advance

  Read the article

• Ubuntu (11.10) fails to connect to wireless network

  - by Tal Galili

  I just installed ubuntu 11.10, and tried to have it connect to the internet. I use a wireless USB stick by edimax (it is called IEEE802.11b/g/n nano USB adapter or also EW-7811Un). My problem is that Ubuntu seems to be able to use the USB to see the networks around me, but when I try to connect to my network - it just keeps trying and failing. I am connected to the internet through a 300M Wireless N Router Model No. TL-WR841N / TL-WR841ND Can you please advise on how this can be resolved? Thanks!

  Read the article

• How To Get a Better Wireless Signal and Reduce Wireless Network Interference

  - by Chris Hoffman

  Like all sufficiently advanced technologies, Wi-Fi can feel like magic. But Wi-Fi isn’t magic – it’s radio waves. A variety of things can interfere with these radio waves, making your wireless connection weaker and more unreliable. The main keys to improving your wireless network’s signal are positioning your router properly — taking obstructions into account — and reducing interference from other wireless networks and household appliances. Image Credit: John Taylor on Flickr How To Get a Better Wireless Signal and Reduce Wireless Network Interference How To Troubleshoot Internet Connection Problems 7 Ways To Free Up Hard Disk Space On Windows

  Read the article

• How to tell if you are connected to Wireless B, G or N?

  - by Raheel Khan

  I am using Windows 7 on all wired desktops and wireless laptops in my home network. I recently upgraded my Ethernet switch to Gigabit and instantly noticed an increase in throughput in wired devices. I also bought a Wireless-N WAP but with degredation in wireless file transfer speeds. I have been told that a number of reasons could affect wireless speeds including which WAP is used, how many wireless devices are connected, which security mode is used, etc. However, that remains irrelevant to my question. Each of my laptops claim to support Wireless-N but I cannot seem to figure out how to determine if the laptops are truly running Wireless-N or are connected to the WAP through some sort of mixed-mode. I do not have control of the WAP device so cannot tell what mode it is running in. Is there a way to tell which mode is being used and what the throughput is for each connected device without having access to the WAP interface?

  Read the article

• Display wireless channels currently in use

  - by DrStalker

  Is there any windows utility to display the wireless channels are currently in use by the available wireless networks? I'd like to be able to see what existing channels are using so I can try to minimize interference on a new access point without a lot of trial and error.

  Read the article

• Wifi - wireless network not working after installing Ubuntu 12.04

  - by Nilesh

  I had installed ubuntu 12.04 in my Dell Vostro 3460. Initially wired as well wireless both are not working. After installing compat-wireless-2012-07-03-pc.tar.bz2 wired network fine but wireless is not working. Previously both were working fine with ubuntu 11.10. Also presently both network are working fine in Win7. lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.4 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 5 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Atheros Communications Inc. AR8161 Gigabit Ethernet (rev 10) iwconfig: lo no wireless extensions. eth0 no wireless extensions. ifconfig: eth0 Link encap:Ethernet HWaddr 84:8f:69:d4:35:9b inet addr:10.24.22.72 Bcast:10.24.31.255 Mask:255.255.224.0 inet6 addr: fe80::868f:69ff:fed4:359b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15332 errors:0 dropped:0 overruns:0 frame:0 TX packets:10425 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:9262594 (9.2 MB) TX bytes:1572030 (1.5 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1432 errors:0 dropped:0 overruns:0 frame:0 TX packets:1432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:145656 (145.6 KB) TX bytes:145656 (145.6 KB)

  Read the article

• No Wireless Networks, BCM4313 [duplicate]

  - by TalonPlz

  This question already has an answer here: How to Install Broadcom Wireless Drivers (BCM43xx) 38 answers Just bought this little Asus 10 inch laptop that came with Ubuntu 12.04. Everything at my home was fine: Wireless identified and connected. As soon as I went to my girlfriend's house the trouble started. I couldn't connect to wireless (authentication... times out and asks for authentication) I started doing internet searching, tried a few solutions posted on line using terminal commands. No solutions. I decided to upgraded to 12.10-13.04 and that left me with a worse problem: I can no longer see ANY networks what so ever. Wireless card is ON, with out a doubt. Wired connection works. I have been fumbling with driver versions to no .avail, and have no idea which driver I am currently running I have a vague idea of what terminal lines to run: lshw: resources: irq:17 memory:f7d00000-f7dfffff *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth2 version: 01 serial: dc:85:de:56:c4:ea width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.20.155.1 (r326264) latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f7d00000-f7d03fff iwconfig: eth1 no wireless extensions. eth2 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off lo no wireless extensions. I am new and excited to start my Ubuntu and Linux life and this is only the first of my few hic cups i am sure! :) Thanks all UPDATE: Report from 2nd answer talon@Black1015E:~$ sudo apt-get remove --purge bcmwl-kernel-source [sudo] password for talon: Reading package lists... Done Building dependency tree Reading state information... Done Package 'bcmwl-kernel-source' is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. talon@Black1015E:~$ wget http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb --2013-10-22 18:50:32-- http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb Resolving us.archive.ubuntu.com (us.archive.ubuntu.com)... 2001:67c:1562::15, 2001:67c:1562::13, 2001:67c:1562::14, ... Connecting to us.archive.ubuntu.com (us.archive.ubuntu.com)|2001:67c:1562::15|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181334 (1.1M) [application/x-debian-package] Saving to: ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ 100%[======================================>] 1,181,334 3.37MB/s in 0.3s 2013-10-22 18:50:33 (3.37 MB/s) - ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ saved [1181334/1181334] talon@Black1015E:~$ arvh No command 'arvh' found, did you mean: Command 'arch' from package 'coreutils' (main) arvh: command not found talon@Black1015E:~$ arch x86_64 talon@Black1015E:~$ sudo dpkg -i bcmwl*.deb Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 171895 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.112+bdcom-0ubuntu3) ... Loading new bcmwl-5.100.82.112+bdcom DKMS files... First Installation: checking all kernels... Building only for 3.8.0-32-generic Building for architecture x86_64 Building initial module for 3.8.0-32-generic Done. wl: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.8.0-32-generic/updates/dkms/ depmod........ DKMS: install completed. Error: Module b43 is not currently loaded Error: Module b43legacy is not currently loaded Error: Module ssb is not currently loaded Error: Module bcm43xx is not currently loaded Error: Module brcm80211 is not currently loaded Error: Module brcmfmac is not currently loaded update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-32-generic rebooting now

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >