Search Results

Search found 2279 results on 92 pages for 'cable clutter'.

Page 20/92 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

  • server and user directly connected no pinging...

    - by jtzero
    I have a server(fedora 12) with two nics on it, directly connected to say 192.168.1.0 and 192.168.2.0 the route table looks like this Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 192.168.1.1 255.255.255.0 U 0 0 0 eth0 192.168.2.0 * 255.255.255.0 U 0 0 0 eth1 eth0 = 192.168.1.15 eth1 = 192.168.2.1 and a directly connected user (Mythdora) on the 192.168.2.0 network with ip 192.168.2.2 and route table like so Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 0 0 0 eth0 the cable is a crossover and it works all three nics work -- connected my laptop to either end and assign it a valid 192.168.2.0 ip the pings will work. In fact if I disconnect the server side and plug the eth cable into the laptop and have thte box ping the laptop continually remove the eth cable and plug it back into the server both sides ping... unfortunately the box realizing it's connected to a different pc wipes its route table after say ten minutes or so. if I do a trace route from a box on the 1.0 network to the servers 192.168.2.1 interface never get a reply from it. as a note at one point I could ping the server from the 192.168.2.2 box but the server couldnt ping the 192.168.2.2 box.

    Read the article

  • How to Load Balance 2 Internet Connections on a Windows 7 machine?

    - by Jimmy Chandra
    It's sort of related to this particular question, but that one is on Mac. I am looking for similar solution on Windows 7. I have 2 network connections: (Connection A) Wireless terminal connecting to ISP A (3G / EVDO internet provider) (Connection B) Broadband wired connection connecting to ISP B (Cable internet provider) Both has access to the internet. When I try connecting to a website and checking the networking tab on my Task Manager, I only see the network traffic being routed to only Connection A. Is there a way to make the computer to utilize both network (in a sense using all the bandwidth available from both the Cable ISP and the 3G / EVDO ISP) at the same time? If so, what do I need to do to set this up ... on Windows 7? Here is a bit more info on my network connections (ipconfig /all): PPP adapter Wireless Terminal: IPv4: aa.bb.ccc.ddd(preferred) Subnet mask: 255.255.255.255 Default Gateway: 0.0.0.0 DNS: aa.ee.f.ggg aa.ee.f.hhh Primary Wins: jjj.ii.k.l Secondary Wins: jjj.ii.k.m Ethernet adapter LAN: IPv4: 192.168.1.100 (connected to a router by wired that itself connect to a cable modem) subnet mask: 255.255.255.0 Default gateway: 192.168.1.1 (the wireless router) DHCP: 192.168.1.1 (the wireless router) DNS: xxx.yy.zz.ww rr.sss.t.uuu For my own privacy, I don't believe the actual number matters, the patterns are representative of the ip numbering scheme...

    Read the article

  • Bridging my laptop's wireless and wired adaptors

    - by stacey.richards
    I would like to be able to connect a desktop computer that does not have a wireless adapter to my wireless network. I could just run a network cable from my ADSL/wireless router to the desktop computer but sometimes this is not practical. What I would really like to do is bridge my laptop's wireless and wired adapters in such a way that I can run a network cable from my laptop to a switch and another network cable from the switch to a desktop computer so that the desktop computer can access the Internet through my ADSL/wireless router via my latop: +--------------------+ |ADSL/wireless router| +--------------------+ | +-------------------------+ |laptop's wireless adaptor| | | |laptop's wired adaptor | +-------------------------+ | +------+ |switch| +------+ | +-----------------------+ |desktop's wired adapter| +-----------------------+ A bit of Googling suggests that I can do this by bridging my laptop's wireless and wired adapters. In Windows XP's Network Connections I select both the Local Area Connection and the Wireless Network Connection, right click and select Bridge Connections. From what I gather, this (layer 2?) bridge will examine the MAC address of traffic coming from the wireless network and pass it through to the wired network if it suspects that a network adapter with that MAC address may be on the wired side, and vice-versa. If this is the case, I would assume that when the desktop computer attempts to get an IP address from a DHCP server (which is running on the ADSL/wireless router), it would send a DHCP broadcast packet which would pass through the laptop's bridge to the router and the reply would return through the laptop's bridge back to the desktop. This doesn't happen. With some more Googling I find some instruction how this can be done with Linux. I reboot to Ubuntu 9.10 and type the following: sudo apt-get install bridge-utils sudo brctl addbr br0 sudo brctl addif br0 wlan0 sudo brctl addif br0 eth0 sudo ipconfig wlan0 0.0.0.0 sudo ipconfig eth0 0.0.0.0 Once again, the desktop cannot reach the ADSL/wireless router. I suspect that I'm missing some simple important step. Can anyone shed some light on this for me?

    Read the article

  • How to test/debug bad network wiring?

    - by Jack Lloyd
    I recently bought a place already wired with Cat 5E (8 ports, leading to a central closet). However attempting to get link, nothing works. On closer examination, it was obvious that the ends in the closet were wired backwards (brown on pin 1, etc). The jacks that I've pulled out of the wall do look to be correctly done. However, testing with a network cable tester shows zero link between any of the jacks and any of the ports in the closet - I had expected to just see a 1/8, 2/7, ... 8/1 mismatch, but instead get nothing at all. The runs are accessible and look neat, though they take some bends that seem quite sharp and are in some cases much longer than they need to be (the person who put this in was a professional electrician but I suspect this was the first time he ran network cabling). My best guess at this point is that he either bought bad cable, or put so much tension on it that he snapped wires. Though it seems surprising/unlikely that I wouldn't get at least one active wire on one of the 8 lines. So, my question: is there anything else I should try or test before I go ripping out everything and running new cable?

    Read the article

  • How do I keep a bridge enabled on a bonded interface?

    - by jlawer
    I'm working on setting up a pair of CentOS 6.3 servers that will run a couple of KVM vms and have come across a problem setting up a bridge on a bond. I am using Mode 4 (802.3ad) bonding on a pair of stacked Dell Powerconnect 5524 switches connecting to R320 servers. There are 2 links (1 to each switch) that form a Link Aggregation Group (802.3ad / LACP bonding). On top of the bond I have VLAN Tagging. I've verified this is a problem on multiple other bonding modes so it isn't just a mode 4 issue. I am testing what happens when 1 link is dropped (ie switch dies, cable breaks, etc). If I don't have a bridge (for KVM), everything works fine, failover happens as expected. If I have the bridge enabled, it works fine until failover (unplugging a cable). When failover happens /var/log/messages shows the slave link going down, followed within a second by: kernel: br1: port 1(bond0.8) entering disabled state The thing is /proc/net/bonding/bond0 shows the link is up as expected (simply with only 1 slave instead of 2). If I plug the cable back in it recovers and brings the bridge back to an enabled state. I actually have tested this while a ping is occuring and if the timing is right a packet will actually leave the system after the link is lost, but before the disabled message occurs. This disabled state I assumed was STP, but I have disabled STP on the bridge configuration and this issue still occurs. brctl showstp br1 still shows the link as disabled when it is running without a slave. I also switched between the nics in the server (I have 2x Broadcom & 4x intel). It doesn't matter which configuration I have. Does anyone know of a way to force the bridge to stay enabled or why its detecting the bond as disabled, when it isn't?

    Read the article

  • How to connect 2 routers (Asmax and D-link)

    - by piobyz
    I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

    Read the article

  • Expresscard Not Detected in PCI-E Adapter

    - by maxpower47
    I'm trying to put an expresscard TV tuner (Avermedia HC82) into my HTPC using this expresscard to PCI-E adapter. I've verified that the tuner works fine in my laptop. The motherboard is a Biostar TF7050-M2. When I install it and turn it on, the light on the back of the adapter comes on fine (there are two indicator lights on the back to show if it is using PCI-E or USB communication, USB communication goes through a USB cable connected between the card and a header on the motherboard) showing that it is working in PCI-E mode. However, the device is never detected in Windows 7 Professional x64. The auto detect never happens, it doesn't show up in the device manager, and I can have it rescan for new hardware and nothing is found. I tested the whole setup (tuner + adapter) in another PC (also using Win 7 Pro x64) and it worked fine. I also tried: Plugging the adapter in to the PCI-E x16 slot on the motherboard (I verified first that the x16 slot worked by installing a video card in it) Booting into safe mode and rescanning Updating the chipset drivers Installing the tuner drivers first Using a different USB cable, plugged in to one of the known good ports on the back of the board Trying it without the USB cable plugged in Removing the other PCI cards that were installed on the board Looking through the BIOS for any setting that might be disabling it somehow to no avail. I'm at a loss for what else to try. I really don't want to RMA it (the shipping back to newegg will be almost as much as it cost to buy in the first place. Any ideas?

    Read the article

  • Find whether TV supports S Video

    - by Vik
    Hello Freinds I have a TV (some unknown model) which has 3 sockets to insert 3 wires red, yellow and white. A DVD Player can be connected to the TV using sockets and the TV displays that the TV is in AV mode when DVD is running. Now i have a Desktop which has a S Video Port and i have a wire to connect the S Video port from my computer to those red, yellow and white sockets using appropriate pins. Now i have searched all over the remote and it does not switches to S Video Mode, it has only 2 modes of operation i.e. 1 Cable Connection (Third Party DTH Receiver receives channels and i pay subscription) and 2 AV Mode. It does not have S Video Mode or any other mode. Now my question is whether i can connect the S Video cable from my desktop to the above described TV or i should look for a new TV if i wish to connect the S Video from Computer to TV or there is any sort of converter that can help? I did tried connecting the S Video cable from Desktop to TV, but it did'nt worked. TV kept on displaying Blue Screen of AV Mode. Regards

    Read the article

  • Why do I need a managed switch and which one should I buy?

    - by ascanio1
    I bought a 2nd router and I want both routers to have direct WAN access to the modem. One of the 2 routers directs VOIP traffic to a telephone line port. This VOIP service is provided by the cable carrier which also leases the modem & the router. The cable company technician told me that this VOIP line uses IPv6 addressing and therefore I must employ an IPv6 capable/compliant Giga Hub/Switch or my telephone line won't work anymore. Pls advise me (brand/model) an IPv6 compliant, 2 port, switch to purchase. Pls educate me: By reading this forum I thought that hubs broadcast traffic to all ports, regardless of which input/output is being used and so, theoretically, they have nothing to do with IP. Correct? Same story for unmanaged switches, where the only difference is that these latter devices route traffic only to those ports which are detected to be in use. Correct? I also understood that unmanaged switches route traffic simply by detecting hardware use and not by selecting specific IP traffic. Correct? Finally, there are managed switches which DO select traffic based on IP and, therefore, only these managed switches are involved with IPv6... Why would my cable company explicitly tell me, over and over, that I must use an IPv6 compliant switch? Why would they need a managed switch instead of an unmanaged one? Thanks in advance for helping me understand!

    Read the article

  • PC -> TV HDMI suddenly doesn't work, any other option does

    - by XSlicer
    So my parents wanted to connect their PC to their TV, so they bought a 10m (35 ft) cable. It all worked perfectly. Then my mom tripped over the cable, breaking it. She somehow got a free replacement, but at the same time some more expensive one from an uncle. Now the problem is that this suddenly doesn't work anymore (TV saying "Format not supported"). I've tried several other things to pinpoint the actual problem, but none brought me something conslusive: PC (hdmi) to TV doesn't work (both cables) PC (hdmi) to TV doesn't work (short cable) Laptop (hdmi) to TV work (same cables) BluRay (hdmi) to TV works (same cables) PC (hdmi) to monitor works (same cables) PC (DVI w/ adapter HDMI) to TV works (same cables) I've tried different ports, tried Linux, reinstalling drivers (the graphics card is internal using an i5 sandy bridge. Normally it's running Windows 7 Home Prem, the TV being a Philips 37PFL7605H). So basically, everything works, except that thing what we want. The only things I am thinking of is that the sound is interfering or that the HDMI-output is somehow broken. Or is it anything else? I'm kind of lost.

    Read the article

  • Wireless Access Point stopped working

    - by Alex Pritchard
    I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

    Read the article

  • Data loss by randomly unplugging the computer during runtime

    - by Kan
    I'm from Austria and we and the Germans have some sort of bad science-show which runs every day. What I call it would rougly translate to "half-knowledge" if you want so. By the way: It is called "Galileo". So they thought they'd make a computer myth busters video right now, and I couldn't believe what I saw and heard... The strangest thing to me was that they asked: "Does unplugging the computer damage your data?" Then they started up some machine with Vista on it, started copying some files and randomly unplugged the PC cable, the whole thing around 50 times. After their computer continued to start up normally, they just said "nothing can happen, your data or computer can't be damaged". They of course excluded unsaved data in running programs like text editors from this. I asked myself: What the hell are their "computer experts" saying? You can't tell by unplugging the cable 50 times if that can damage your computer. Can unplugging the cable during runtime cause data loss (as said by the moderator of the show)? (I destroyed my windows registry once during a reset)

    Read the article

  • Rendering a frame is producing noise from speakers in Windows and Linux

    - by Robber
    When any hardware accelerated application is rendering a frame (or many of them) a very short noise is coming from my speakers. This can be a game, a WebGL application or XBMC. When the application/game is rendering many frames per second (like most of them do) the noise is a continuous buzzing that gets higher pitched with higher framerates. This applies to Linux and Windows, so I'd assume it's a hardware problem. The current hardware in the PC is: CPU: Core2Quad Q9550 GPU: Radeon HD 5770 RAM: 2x2GB DDR2 Motherboard: Asus P5QLD PRO PSU: be quiet! Pure Power 530W Screen and speakers: Old 720p LCD TV connected via VGA and aux cable Muting the TV stops the noise, muting Windows doesn't. I tried replacing the PSU first (used a Tagan 700W PSU before) because I thought it was a power problem. It wasn't. I tried replacing the motherboard (used a ASUS P5B SE before) next because I thought it was a sound card problem. It wasn't. I tried the GPU in a different PC because I thought it was a broken graphics card. It worked perfectly fine in the other PC. I thought it might be interference, but moving the audio cable around changes absolutely nothing. I tried using an HDMI cable instead and that did work, but is not an option since my TV has only one HDMI input and I need that for my PS3.

    Read the article

  • Watchguard Firebox "split" fibre optic line into 2 interfaces

    - by fRAiLtY-
    We have a requirement on our Watchguard Firebox XTM505 to be able to split our incoming external interface, in this case a fibre optic dedicated leased line, 100/100. We use the line in our office of approx 30 machines however we also re-sell to an external company who utilise it to provide wireless internet solutions to the public. The current infrastructure is as follows: Data in (Leased Line) - Juniper SRX210 managed by ISP - 1 cable out into unmanaged Netgear switch - 1 cable into our firewall and office network, 1 cable to our external providers core router managed by them. We have been informed that having the unmanaged switch in the position it is poses a security risk and that a good option would be to get our Watchguard Firewall to perform the split, by separating our office onto a trusted interface, and by "passing through" the external line to their managed router. It is alleged that the Watchguard is capable of doing this and also rate limiting the interfaces, i.e. 20mbps for the trusted interface and 80mbps for the "pass-through", however Watchguard technical support don't seem to be able to understand what we're trying to achieve. Can anyone provide any advice on whether this is possible on a Watchguard device and how or perhaps if there's a better way of achieving this, perhaps with a managed switch instead of unmanaged? Cheers

    Read the article

  • Sudden "No Signal" in HDMI-DVI connection

    - by nazikus
    Yesterday I have connected external display Asus VW192C to my laptop Dell XPS 14-L421X via HDMI-to-DVI-D cable. And it worked perfectly fine from start. The day after, Asus screen went blank showing "No signal". Every time I connection/disconnection cable or power off/on the display it says "No signal". And I didn't change any system configurations meanwhile. To troubleshoot the problem, I have tried to connect laptop to TV (hdmi-to-hdmi) - it was fine. I've tried to connect a different laptop to the display via the same cable - worked fine as well. So its obviously something on system level, either Windows or graphics drivers. Also it seems that Windows still see the external display (I can move mouse pointer away from the main screen in Extended mode), but there's just no signal. Any ideas? What else to try? PS. My laptop has 2 graphics cards - GeForce 630M and Intel HD 4000 using NVidia Optimus technology. I have updated to latest Intel and NVidia drivers, still didn't help. PPS. Although I shouldn't have updated (from Intel support): "our Intel generic graphics drivers from the Intel website do not support using both Intel Graphics 4000 and NVidia GeForece GT630M". Nevertheless, it should not affect connectivity to additional display.

    Read the article

  • My Hard Drive isn't Working

    - by MeCB
    I never use Safely Remove Hardware with Windows XP. It has been working for me for years with my SD card, mouse, hard drive and memory stick. My hard drive has a USB cable and power cord so I can hook it up to any desktop hard drive. Now my hard drives don't like this and I did not know this till now. I am always careful and to wait till it is all finish accessing the USB before I unplug it. Now three of my hard drives can't be seen by Windows, though the others still work. when I hook it up to another computer it works fine. I use the same USB cable to hook up all of my hard drives one at a time. So my USB cable is good. I think that when I unplugged the hard drive this one time, it had a file it still wanted to see and now only this drive does not work only this computer. Then the same thing happens to my other two hard drive after I used it for a week with the same cables. How can I fix this?

    Read the article

  • securing communication between 2 Linux servers on local network for ports only they need access to

    - by gkdsp
    I have two Linux servers connected to each other via a cross-connect cable, forming a local network. One of the servers presents a DMZ for the other server (e.g. database server) that must be very secure. I'm restricting this question to communication between the two servers for ports that only need to be available to these servers (and no one else). Thus, communication between the two servers can be established by: (1) opening the required port(s) on both servers, and authenticating according to the applications' rules. (2) disabling IP Tables associated with the NIC cards the cross-connect cable is attached to (on both servers). Which method is more secure? In the first case, the needed ports are open to the external world, but protected by user name and password. In the second case, none of the needed ports are open to the outside world, but since the IP Tables are disabled for the NIC cards associated with the cross-connect cables, essentially all of the ports may be considered to be "open" between the two servers (and so if the server creating the DMZ is compromized, the hacker on the DMZ server could view all ports open using the cross-connect cable). Any conventional wisdom how to make the communication secure between two servers for ports only these servers need access to?

    Read the article

  • Can only ssh when not using wifi

    - by AChrapko
    So I have 3 machines, a windows 7 desktop that is always wired to my router, osX laptop, and raspberry pi running debian linux. My router is a Linksys e1000 wireless N. My goal is to be able to ssh the raspi from any machine, while it is connected via wifi. My problem is that when trying to ssh from either the win7 or osX to the Pi it either times out, or gives an error: "ssh: connect to host 192.168.1.### port 22: No route to host" The only times that I have managed to connect to the pi from any machine were when it connected to the router via an Ethernet cable. Currently with win7 desktop wired, macbook wireless, and pi wireless tests give the following: win7 ping macbook: Destination host unreachable. macbook ping win7: Request timeout. win7 ping pi: Destination host unreachable. macbook ping pi: Request timeout. blah blah blah Plugging the macbook into the router with an Ethernet cable all communication between win7 and macbook works. Pings, ssh, ftp, smb ect... No changes to the pi, still no connections possible to or from any of the other 2 machines. Note All machines, are able to connect to the internet and ssh to the same machine on a completely different network, wired or over wifi. Plugging the Pi in with Ethernet (and macbook still wired) I can ssh to the pi from both win7 and macbook. I can ssh from the pi to macbook. All machines still able to connect the the off network machine. Also another little side note- I was playing warcraft 3 with my roommates the other day, and the only time they were able to see my LAN game was when they were plugged into the router with an Ethernet cable. Once or twice one of the laptops was able to connect over wifi, but not without another computer connecting first via Ethernet. So basically does anyone have any info as to why my router seems to completely ignore local wireless traffic?

    Read the article

  • Is a modem required to be programmed when using with an internet provider?

    - by Tim
    I wonder if a modem is required to be programmed when using with an internet provider? If yes, what is the purpose of programming a modem? Do both a DSL and a cable ISP both require a modem to be used in an individual home? For example, I have a Motorola modem SURFboard Model:SB5101, Customer S/N: xxx S/N? xxx HFC MAC ID: xxx USB CPE MAC ID: xxx a coil of cable and a splitter from Comcast High-Speed internet Self-Installation Kit, which were bought 5 years ago, when I purchased Comcast internet service from its retailer www.comcastoffers.com. With them, I was hoping to reduce the amount of fee by avoiding to ask Comcast people to come over to install. But I remember at that time Comcast sent its technician here, dismissed my idea of self-installation, saying they needed to use their own modem and charging me a hefty fee, and so my equipments have never been used. I haven't been using Comcast for a long time. I wonder if my modem, cable and splitter (brand new, never used) are still good to use with an internet provider such as Comcast? If needed, we can ignore their policy and just consider the technology side? Or they are not good to use and I must throw them away like trash? Thanks and regards!

    Read the article

  • Media Disconnected Networking Issue

    - by Chris
    After rearranging my physical network in my apartment my Windows Vista machine can no longer connect to the network. I have tested all of the cabling by connecting other devices and everything is fine. I'm able to connect using other computers, I've even tested a brand new ethernet adapter and the network status still reads "media disconnected". I have no idea where to go from here. My setup is as follows: Cable modem - router - hardwired ethernet cable to computer.

    Read the article

  • Refreshing Your PC Won’t Help: Why Bloatware is Still a Problem on Windows 8

    - by Chris Hoffman
    Bloatware is still a big problem on new Windows 8 and 8.1 PCs. Some websites will tell you that you can easily get rid of manufacturer-installed bloatware with Windows 8′s Reset feature, but they’re generally wrong. This junk software often turns the process of powering on your new PC from what could be a delightful experience into a tedious slog, forcing you to spend hours cleaning up your new PC before you can enjoy it. Why Refreshing Your PC (Probably) Won’t Help Manufacturers install software along with Windows on their new PCs. In addition to hardware drivers that allow the PC’s hardware to work properly, they install more questionable things like trial antivirus software and other nagware. Much of this software runs at boot, cluttering the system tray and slowing down boot times, often dramatically. Software companies pay computer manufacturers to include this stuff. It’s installed to make the PC manufacturer money at the cost of making the Windows computer worse for actual users. Windows 8 includes “Refresh Your PC” and “Reset Your PC” features that allow Windows users to quickly get their computers back to a fresh state. It’s essentially a quick, streamlined way of reinstalling Windows.  If you install Windows 8 or 8.1 yourself, the Refresh operation will give your PC a clean Windows system without any additional third-party software. However, Microsoft allows computer manufacturers to customize their Refresh images. In other words, most computer manufacturers will build their drivers, bloatware, and other system customizations into the Refresh image. When you Refresh your computer, you’ll just get back to the factory-provided system complete with bloatware. It’s possible that some computer manufacturers aren’t building bloatware into their refresh images in this way. It’s also possible that, when Windows 8 came out, some computer manufacturer didn’t realize they could do this and that refreshing a new PC would strip the bloatware. However, on most Windows 8 and 8.1 PCs, you’ll probably see bloatware come back when you refresh your PC. It’s easy to understand how PC manufacturers do this. You can create your own Refresh images on Windows 8 and 8.1 with just a simple command, replacing Microsoft’s image with a customized one. Manufacturers can install their own refresh images in the same way. Microsoft doesn’t lock down the Refresh feature. Desktop Bloatware is Still Around, Even on Tablets! Not only is typical Windows desktop bloatware not gone, it has tagged along with Windows as it moves to new form factors. Every Windows tablet currently on the market — aside from Microsoft’s own Surface and Surface 2 tablets — runs on a standard Intel x86 chip. This means that every Windows 8 and 8.1 tablet you see in stores has a full desktop with the capability to run desktop software. Even if that tablet doesn’t come with a keyboard, it’s likely that the manufacturer has preinstalled bloatware on the tablet’s desktop. Yes, that means that your Windows tablet will be slower to boot and have less memory because junk and nagging software will be on its desktop and in its system tray. Microsoft considers tablets to be PCs, and PC manufacturers love installing their bloatware. If you pick up a Windows tablet, don’t be surprised if you have to deal with desktop bloatware on it. Microsoft Surfaces and Signature PCs Microsoft is now selling their own Surface PCs that they built themselves — they’re now a “devices and services” company after all, not a software company. One of the nice things about Microsoft’s Surface PCs is that they’re free of the typical bloatware. Microsoft won’t take money from Norton to include nagging software that worsens the experience. If you pick up a Surface device that provides Windows 8.1 and 8 as Microsoft intended it — or install a fresh Windows 8.1 or 8 system — you won’t see any bloatware. Microsoft is also continuing their Signature program. New PCs purchased from Microsoft’s official stores are considered “Signature PCs” and don’t have the typical bloatware. For example, the same laptop could be full of bloatware in a traditional computer store and clean, without the nasty bloatware when purchased from a Microsoft Store. Microsoft will also continue to charge you $99 if you want them to remove your computer’s bloatware for you — that’s the more questionable part of the Signature program. Windows 8 App Bloatware is an Improvement There’s a new type of bloatware on new Windows 8 systems, which is thankfully less harmful. This is bloatware in the form of included “Windows 8-style”, “Store-style”, or “Modern” apps in the new, tiled interface. For example, Amazon may pay a computer manufacturer to include the Amazon Kindle app from the Windows Store. (The manufacturer may also just receive a cut of book sales for including it. We’re not sure how the revenue sharing works — but it’s clear PC manufacturers are getting money from Amazon.) The manufacturer will then install the Amazon Kindle app from the Windows Store by default. This included software is technically some amount of clutter, but it doesn’t cause the problems older types of bloatware does. It won’t automatically load and delay your computer’s startup process, clutter your system tray, or take up memory while you’re using your computer. For this reason, a shift to including new-style apps as bloatware is a definite improvement over older styles of bloatware. Unfortunately, this type of bloatware has not replaced traditional desktop bloatware, and new Windows PCs will generally have both. Windows RT is Immune to Typical Bloatware, But… Microsoft’s Windows RT can’t run Microsoft desktop software, so it’s immune to traditional bloatware. Just as you can’t install your own desktop programs on it, the Windows RT device’s manufacturer can’t install their own desktop bloatware. While Windows RT could be an antidote to bloatware, this advantage comes at the cost of being able to install any type of desktop software at all. Windows RT has also seemingly failed — while a variety of manufacturers came out with their own Windows RT devices when Windows 8 was first released, they’ve all since been withdrawn from the market. Manufacturers who created Windows RT devices have criticized it in the media and stated they have no plans to produce any future Windows RT devices. The only Windows RT devices still on the market are Microsoft’s Surface (originally named Surface RT) and Surface 2. Nokia is also coming out with their own Windows RT tablet, but they’re in the process of being purchased by Microsoft. In other words, Windows RT just isn’t a factor when it comes to bloatware — you wouldn’t get a Windows RT device unless you purchased a Surface, but those wouldn’t come with bloatware anyway. Removing Bloatware or Reinstalling Windows 8.1 While bloatware is still a problem on new Windows systems and the Refresh option probably won’t help you, you can still eliminate bloatware in the traditional way. Bloatware can be uninstalled from the Windows Control Panel or with a dedicated removal tool like PC Decrapifier, which tries to automatically uninstall the junk for you. You can also do what Windows geeks have always tended to do with new computers — reinstall Windows 8 or 8.1 from scratch with installation media from Microsoft. You’ll get a clean Windows system and you can install only the hardware drivers and other software you need. Unfortunately, bloatware is still a big problem for Windows PCs. Windows 8 tries to do some things to address bloatware, but it ultimately comes up short. Most Windows PCs sold in most stores to most people will still have the typical bloatware slowing down the boot process, wasting memory, and adding clutter. Image Credit: LG on Flickr, Intel Free Press on Flickr, Wilson Hui on Flickr, Intel Free Press on Flickr, Vernon Chan on Flickr     

    Read the article

  • The Best Free Programs for Using Virtual Desktops in Windows

    - by Lori Kaufman
    If you often open a lot of applications at once, a virtual desktop program can help you keep all those windows on your desktop organized. A virtual desktop program allows you to put open applications into separate virtual desktops, cutting down on your desktop clutter. We’ve collected links to and information about several free virtual desktop managers you can use to organize your Windows desktop. How to Factory Reset Your Android Phone or Tablet When It Won’t Boot Our Geek Trivia App for Windows 8 is Now Available Everywhere How To Boot Your Android Phone or Tablet Into Safe Mode

    Read the article

  • How to merge your referenced assemblies into the output assembly for improved usability

    - by Daniel Cazzulino
    Something we've been doing in moq since the very beginning is to have a single assembly as output: Moq.dll. This reduces the clutter for users and lets them focus on what they need from our library, rather than getting the noise of whatever third-party (or internal) libraries we use to implement it. This is good from the deployment point of view too, and if all your libraries are actually internal infrastructure assemblies, you can even make them all internal types of your output assembly....Read full article

    Read the article

  • Website Optimisation - The Impact of Blended Real-time Search So Far

    Despite the initial hype surrounding the introduction of blended real-time search into internet search engines, many experts have begun to question its value to website optimisation. Real time search has been widely criticised as a cause of SERP clutter, making pages appears chaotic and leaving the user struggling to decide which links may actually provide the information they are after.

    Read the article

  • Can I use wikipedia/commons images to create a logo for my program?

    - by bitmask
    I'm not perfectly clear on the implications of the GFDL for reusing pictures in this manner. Would adding a reference in the git's root folder's README suffice, or would that clutter every use of the logo, as you would have to attribute all original contributors on every single usage (like, e.g. presentations, flyers, websites, ...)? The software itself qualifies as FOSS, although it doesn't have a GNU* license.

    Read the article

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >