Search Results

Search found 2279 results on 92 pages for 'cable clutter'.

Page 16/92 | < Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >

  • VPN Network intermittantly fails to provide internet: What could be possible causes

    - by Jake M
    We have a small office with our own VPN setup. We occasionally experience failures in our internet connection where we cannot access the internet. Most of the time the internet connection will resume by itself(without me doing anything) after a period of time(10 mins). Would you be able to suggest possible causes of the connection failure so I can then go and run some tests? Our network architecture is like so: A 'Billion' brand router that is connected to the internet via phone cable and then connected to our Cisco Switch A Cisco Switch/Bus which is connected to all our office nodes, our external harddrive and also to our router as stated above. All connections are via ethernet cable A series of work computers(nodes) connected via ethernet cable to the Cisco switch. Our ISP is TPG Australia We have a Virtual Private Network All the ethernet cables are about 3 years old Do you think that the causes of our intermittant connection problems could be due to the following: Data collisions in the ethernet cables Old/Faulty ethernet cables Our ISP has bad service Can you think of any other causes of the problem?

    Read the article

  • X-FI optical output not being recognized.

    - by Luciano
    Hello there! I have an issue and I don't know what to do! I have a SoundBlaster X-FI Xtreme Gamer, which has a spdif mini-optical output. I have it connected to a home theater, via a toslink cable and an adapter to fit in the mini plug. It used to work perfectly, but now it doesn't anymore. There is light travelling through the cable, but the HT doesn't pick up the signal. The sound card of the motherboard also has an optical output (regular, not mini) and it works ok, so the cable and the HT are fine, I think. What else should I try? Thanks, Luciano. PS: I only enabled the onboard card for testing, but usually it's disabled to avoid any kind of conflicts. PPS: I'm using Windows 7 64bit with latest drivers of everything, but like I said. It used to work.

    Read the article

  • How to force a resolution in linux?

    - by hi
    I have a HP LP3065 that requires a dual link dvi cable to go up to 2560x1600 resolution. However, I do not have that cable, but I want to use 1920x1200 resolution. However, my nVidia Display Settings (also system display settings) will only go up to 1280x1024, which looks horribly pixelated on the 30". How do I force the 1920x1200 resolution? I tried adding the mode into my xorg.conf file, but it still would not take it. I know my vid card can do 1920x1200 since it works on the 24" monitor with the same dvi cable. Here are my specs: Fedora 12 Nvidia Quadro NVS 420 Intel Xenon E5530 cpu 6gig memory Thanks

    Read the article

  • Mac OS X: pushing all traffic through a VMWare VM [closed]

    - by bj99
    I want to set up an Astaro (Sophos) UTM in a Virtual Machine. The Setup should be at the end the following: Cable Modem (one IP adress) | [Ethernet] Sophos UTM (running as VM [VMWare Fusion 5] on the MacMini) | [WIFI] Airport Express v2 (for sharing Local Network to wireless and wired clients) 1)| [WIFI] 2)| [Ethernet over Thunderbolt Ethernet Adapter]* Clients MacMini (Local File Server) *To have the Mini also protected behind the UTM So the setup process for the UTM works fine, but then the problems start: I just have one external IP (from my cable modem provider)== So if I put the VM in briged mode my Internet connection drops, because the MacMini also has its IP adress. If I put the VM to NAT mode the Mini itself is not protected by the UTM So: is there a way to hide the en0 interface(Ethernet) and the en1 interface (Wifi) from the MacMini, so that they not even appear in System Preferences Network section but are available to the VM? That way the Mini must connect to the en2 interface (Thunderbolt adapter) to make any Internet/LAN connection and I just use the given single IP from the Cable Modem. Thaks for any suggestions... Sebastian

    Read the article

  • 3.5mm headphone jack -> Component video?

    - by Isaac Waller
    Hello, I have a strange cord that has a male 3.5mm headphone jack on one side, and some component video and audio ouputs on the other. When I plug the headphone side into my computer, and the other side into my TV, I get audio across the cable, but no video. How can I send some video over the headphone jack in OS X? I know you can, because this cable is actually for a Beyblade toy and it somehow transferred video over this cable. Thanks, Isaac I think I found some more information (from Wikipedia:) "A four conductor version (of a 3.5mm headphone jack) is becoming a de facto standard output connector for compact camcorders, providing stereo sound plus a video signal." So how can I do this on Mac?

    Read the article

  • Do all the network cards use the same frequency to send signals to wire?

    - by smwikipedia
    I am comparing my cable TV wire to my network wire. In a TV cable wire, different frequencies are used by different TV channels. And since a certain channel use a fixed frequency, I think the only left way to represent different signal is with the carrier wave's amplitude. But what about the network wire? For all the network cards with the same type, do they also use different frequencies to send signals just like TV cable? I vaguely remember that they use frequency adjustment to represent signals. So the frequency should not be a fixed one. So how did all the network cards that sharing the same medium differentiate their own signal from others?

    Read the article

  • Laptop charger disconnects and reconnects, charger or battery broken?

    - by Rob
    I've got an Acer Aspire One netbook (AOA-150) and there's obviously something wrong with it. The charging port gets VERY HOT and the charger seems to disconnect and reconnect quickly sometimes. This only happens when the netbook is running, and it doesn't seem to care what it's doing other than being on. The battery has an extremely short life (< 30minutes, sometimes) and I almost exclusively run it on the power cable (which needs the battery plugged in. Having it just plugged into the wall won't start up). Does this sound like a problem with the power cable or the battery? The plug for the cable and the port get so hot that if I held them for longer than a few seconds, I'm sure I'd get burnt. EDIT Just got "Popular Question" on this and it WAS the power jack. The ground on it came loose from the board. A bit of solder on it and everything is working great again.

    Read the article

  • Connect to development server via switch?

    - by letseatfood
    I apologize upfront if this isn't appropriate for superuser. I asked it on serverfault and was told it was too general for that site. I have a laptop with Vista and it receives it's internet connection wireless. I have an old desktop with Ubuntu 10.04 Server Edition installed and it is setup as a development server with Apache, MySQL, and PHP. This works well, with the server having a static IP address. The server is connected to the router via an Ethernet cable. Is it possible to disconnect the cable that is currently connecting the server and the router, then connect the server and workstation to a switch, so that I am still able to connect to the server via web browser from the workstation? I am trying to eliminate the long ethernet cable connecting the server to the router in the other room. I already have a switch, that is why I asked specifically about it. Thanks and I will be more than happy to clarify!

    Read the article

  • Sharing internet connection from Windows XP using wi-fi router

    - by Darius
    Hi, I have an network configuration like: Ethernet cable from ISP connected to Windows XP machine, configured with static IP 192.168.0.3 Another ethernet connection from 2nd Windows XP machine's network adapter to a Wi-Fi router (D-Link Airport G+) XP set to "Share internet connection", the 2nd adapter configured as static to 192.169.0.1 D-Link Airport Wi-Fi router also configured as "static connection", it's IP set to 192.169.0.2, default gateway set to 192.169.0.1. Network mask everywhere is 24. Laptop computer connected with the router with static IP 192.169.0.3 The problems are: XP machine sees the router (it's able to ping it and access it via the web admin tool) The router somehow cannot PING the XP machine (using the tool provided by the web-based admin tool) The laptop computer cannot ping anything and cannot be pinged The router is only accessible when the ethernet cable is connected with a router's 1-4 LAN port, when I connect it via "WAN" port (which I believe is the proper one) it's not visible from the XP machine If you have similar experience with configuring a network like this I would really appreciate your help. I cannot use the Wi-Fi router with the ISP cable itself.

    Read the article

  • external HDD with SATA & USB interface?

    - by Greg
    Anyone know of an external HDD that would have (in addition to USB) a SATA (eSATA) port/cable? i.e. Brand/Model. Preferably one of the name brands so I have a better change of finding it here or locally if possible. Background - In one location I want to use it is I would like to increase the performance by cabling it directly to the PC SATA port, HOWEVER I don't want to have to open up the PC to do this each time. I was thinking of running a SATA cable out through the PC case so I just plug it directly into the external HDD in question. Perhaps it should be also externally powered too so I don't need to run a power cable out from the PC power supply.

    Read the article

  • Is there a performance difference between Cat5 and Cat6 keystone blocks?

    - by Scott Anderson
    I'm going to be wiring my home for ethernet soon, and I've already decided that I want to use Cat6 cable to do it (faster speeds, better performance, etc). During the installation, I'd like to add wall-plates to certain rooms in my house, and the keystone blocks look like the best option for me. My question is: I've seen different keystone blocks on many cabling websites, some say Cat5e and some say Cat6. The Cat6 ones are slightly more expensive. Is there any noticeable performance gain from using a Cat6 keystone? To me, it just seems like the keystone really wouldn't matter, since it's basically like putting an RJ-45 end on a cable. Can I buy the cheaper Cat5e keystone blocks and still have the performance that Cat6 cable will give me? Thanks!

    Read the article

  • Mac OS X: pushing all traffic through a VMWare VM

    - by bj99
    I want to set up an Astaro (Sophos) UTM in a Virtual Machine. The Setup should be at the end the following: Cable Modem (one IP adress) | [Ethernet] Sophos UTM (running as VM [VMWare Fusion 5] on the MacMini) | [WIFI] Airport Express v2 (for sharing Local Network to wireless and wired clients) 1)| [WIFI] 2)| [Ethernet over Thunderbolt Ethernet Adapter]* Clients MacMini (Local File Server) *To have the Mini also protected behind the UTM So the setup process for the UTM works fine, but then the problems start: I just have one external IP (from my cable modem provider)== So if I put the VM in briged mode my Internet connection drops, because the MacMini also has its IP adress. If I put the VM to NAT mode the Mini itself is not protected by the UTM So: is there a way to hide the en0 interface(Ethernet) and the en1 interface (Wifi) from the MacMini, so that they not even appear in System Preferences Network section but are available to the VM? That way the Mini must connect to the en2 interface (Thunderbolt adapter) to make any Internet/LAN connection and I just use the given single IP from the Cable Modem. Thaks for any suggestions... Sebastian

    Read the article

  • Windows 7 unload driver/disconnect usb before restart

    - by brux
    In xp, my Tascam US 122 usb audio interface works fine. On my windows 7 computer the device works, however when i restart/shutdown it hangs at the "shutting down" screen forever. If the usb cable is removed prior to initiating restart/shutdown then everything goes fine, the computer restarts as normal. This is a known problem, running any other driver in compatibility mode doesnt fix the problem. Is there a method I can use to unload the device/drivers so that I dont have to reach round physically and disconnect the cable. Somebody suggested a spdt switch on the cable itself, but I am looking for a simpler method. Surely I can automate the unloading of the device through a script or such? Any ideas are greatly welcomed thanks

    Read the article

  • Does a bad Internet connection increase bandwidth usage?

    - by Synetech
    My (Rogers) cable connection has been pretty bad recently (channels 3 and 10 are particularly fuzzy—it’s analog, not digital cable). Not surprisingly, this has caused my cable modem to drop out and have to reestablish a connection a couple of times since it started. The poor connection of course means higher corruption (not necessarily dropped per se) which causes the TCP/IP stack to have to retransmit packets more often. Reduction of bandwidth throughput aside, I got to wondering if it increases the actual bandwidth usage. That is, if there is a high error rate on the line causing packets to have to be retransmitted: Does this increase a bandwidth monitoring program’s numbers? Does the ISP count the retransmitted packets toward the monthly cap? Based on what I remember from my university networking courses and common sense, I have a feeling that the answer to both questions is yes, but I cannot reliably measure the first, and have no authoritative answer for the second. I’m wondering if maybe the retransmitted packets are acknowledged as being duplicates and thus not counted somewhere along the line.

    Read the article

  • Intermittent USB 3.0 access - How do I troubleshoot?

    - by Billy ONeal
    I've got a WD Passport hard disk with "superspeed" USB 3.0 support. When I use my USB 3.0 flash drive (this is a Lenovo X220 laptop), USB 3.0 consistently works. But when I use the passport drive, almost without fail the connection drops to USB 2.0. Touching the cable seems to immediately trigger the problem, but it seems to happen on its own though. I've got another cable on order right now... but is it likely the cable's the issue here? Is there anything else I can check?

    Read the article

  • Bridging two connections in windows 7

    - by Serban Razvan
    I have recently bought an Samsung UE32ES5500 and I want to connect it to the internet. Not wanting to buy an expensive Samsung wireless adapter for the TV, I've decided to use an ethernet cable. Because the Internet cable passes through underground to the bedroom and the TV is located in the living room, i decided to put a router in the bedroom, and receive it's signal in the living room using a windows 7 laptop. Afterwards I connected the laptop to the TV through an ethernet cable, and bridged the two connections in Network Connections in Control Panel on the laptop. The TV successfully finds the laptop (and the router I think) but still cannot connect to the internet. Does anyone knows a solution to this problem? (the connections must be bridged because I want to have only one network in the house)

    Read the article

  • How to fix unstable RJ45 jacks? [closed]

    - by BeemerGuy
    This is a little project I'm doing at home. I wanted to wire two rooms together (basically, the router is one room, and the switch is in the second room). So I ran a CAT5 between the two rooms, and wired an RJ45 jack in each room. I then hooked up the two jacks with two CAT5 cable to run it through the cable tester, and all 8 wires seem good. Now, when I connect the switch and the router, the connection is unstable -- I ping the router and it barely holds on for two pings before it disconnects, and stays in that unstable state. Just to make sure the router and the switch are ok, I connected them with long wire between the two rooms and the connection is absolutely stable, and pings continuously. What could be the cause for the unstable connection? Especially that it pings a few times, so there IS a connection. But why is it unstable? And how come the cable tester says it's ok, but it's unstable?

    Read the article

  • Ubuntu 9.10 freezes when HDMI port is connected

    - by Felipe Hummel
    Hi, I have a Sony Vaio FW350 with a HDMI output. I'm trying to use it under Ubuntu 9.10 with a LG LCD monitor 21,5'. I've tried two approaches: Boot the laptop with the HDMI cable connected and monitor turned on. Result: LCD Monitor keeps turned on but the whole screen is black and Ubuntu do not seem to be initializing. Boot Ubuntu until the end. I then connect the HDMI cable into the Laptop. The mouse and the whole system freezes. In both cases the only way to turn off the laptop is holding the power button. I've looked around the internet for similar problems, but only found workarounds for the same problem with VGA input, not HDMI. I also tried to use metacity before connecting the cable, but still got the same result. Any hints?

    Read the article

  • Upgrading HP DL185 G5 8LFF, is using a Dell J1520 4-Drop SATA Adapter possible?

    - by jpreed00
    The HP DL185 G5 8LFF model supports 8 3.5" drives and 1 optical drive. However, instead of the optical drive, I'd like to have 2x 2.5" drives instead. The problem is that the PSU has no more SATA power cables (even though the motherboard has 4 additional SATA data ports). The PSU does have a free 10-pin connector and it looks like the J1520 cable from Dell would fit the bill. Link to cable description Does anyone have any experience using these cables? Are they safe? Any other ideas for adding the disks to the server if I don't use the cable? Thanks!

    Read the article

  • Network router and switch configuration

    - by gilly3
    Can I put a switch before my router in my home network? Here is a diagram of how I want to set up my network: ________________________________ ________________________________________ | | | | | Cable Access Panel | | Home Office | | _____________ ________ | | _____________ | | | | | | | | | | _________ | | | Cable Modem |--->| Switch |-------------->| Router |____| | | | |_____________| |________| | | |_____________| | Printer | | |______________________/____\____| | / | \ |_________| | ___/_ _\___ | _____/ ____|____ \_____ | | | | | | | | | | | | | | PC1 | | PC2 | | | PC3 | | Ext. HD | | PC4 | | |_____| |_____| | |_____| |_________| |_____| | |________________________________________| The reason I want to do this is because my router is also my wireless access point. My cable modem is located in the far corner of my home where my phone/tv/network access panel is. I'd rather keep the wireless access point in a more central location, but I'm not sure if DHCP will continue to work properly with that configuration. Edit: I'd like to continue to be able to share files and access my networked drive and printer from each computer in the house.

    Read the article

  • How to setup a wired local area network in Windows 7?

    - by user883434
    I am using a Lenovo ThinkPad X200 and want to se tup a wired local area network. How could I achieve this? Actually, my question is very simple. I just want to connect to the internet and I have a cable connection at home. So, I just want to plug the cable line to my notebook (x200) so that I can access the internet via the cable. But I dont know how to setup a local area connection in notebook. Since it automatically appear in my desktop, but not in my notebook. Thanks!

    Read the article

  • Ubuntu 9.10 freezes when HDMI port is connected

    - by Felipe Hummel
    I have a Sony Vaio FW350 with a HDMI output. I'm trying to use it under Ubuntu 9.10 with a LG LCD monitor 21,5'. The laptop has a Intel 4500 video card. I've tried two approaches: Boot the laptop with the HDMI cable connected and monitor turned on. Result: LCD Monitor keeps turned on but the whole screen is black and Ubuntu do not seem to be initializing. Boot Ubuntu until the end. I then connect the HDMI cable into the Laptop. The mouse and the whole system freezes. In both cases the only way to turn off the laptop is holding the power button. I've looked around the internet for similar problems, but only found workarounds for the same problem with VGA input, not HDMI. I also tried to use metacity before connecting the cable, but still got the same result. Any hints?

    Read the article

  • Network configuration with limited hardware

    - by Pavel
    I have cable internet and I have two PC. One of them has wireless and ethernet, the other pc has ethernet only. Also, I have a dsl modem that has wireless builtin (some common speedstream model). My goal is to connect all of them so that both have internet access. As I understand, I have two options: connect speedstream to the cable and then connect other PC's to speedstream; OR, connect pc with wireless to the cable and then connect the other pc that has ethernet only using ethernet+wireless through speestream. First one seems to be easy, but it doesn't seem to work. What about the other choice? Is it possible to do it?

    Read the article

  • make a computer recognized as a usb flash drive?

    - by user137560
    Is there anyway to make a folder or a partition on a computer (Linux/windows) to act like a flash drive to other computers or devices when connected with a usb cable. For example, I have a windows 7 computer with 2 partitions c and d, then connect that computer to another computer or a smart TV using a USB cable (has to be male to male USB cable) then the other computer or TV recognizes the current computer as a usb device. Is that possible, if not is there any usb switch to connect an external hard drive or flash drive to both the computer and TV without the need to manually switch them (I know about some USB switches but they only support automatic switching with some certain types of printers, not with mass storage) Thanks in advanced! Sam

    Read the article

  • Does Asus F8SV supports 1920*1080 resolution through DVI output? [closed]

    - by Col
    Devices: Asus F8Sv Laptop (Windows 7 ultimate, GeForce 8600m GT, display driver is 301.42, detected and downloaded from nvidia.com, VGA and DVI output interface) Gateway 23 inches LCD monitor (VGA, DVI-D with HDCP, and HDMI input) 18 pins DVI cable, VGA cable, both new. Problems: When connect laptop to monitor by VGA, resolution is automatically adapted to 1920*1080; but when using DVI connection, resolution on monitor is fixed to 1024*768, which is lower than my laptop default 1280*800. The maximum resolution in windows control panel is only 1024*768, while the Nvidia control panel provides options 1920*1080p and 1920*1080i, but clicking apply button does not work, the resolution just can not change. Possibly reason I guess: GeForce 8600m GT does not support 1920*1080 resolution through DVI outputs. Can anyone confirm it or give the real reason? edit: Problem solved by buying a HDMI to DVI-D adapter. Using this adapter and a HDMI cable, I can now enjoy 1080p movie.

    Read the article

< Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >