Search Results

Search found 1359 results on 55 pages for 'doubt'.

Page 20/55 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

• Disadvantages of enabling AHCI after Win7 install

  - by Mario De Schaepmeester

  I've formatted my notebook that has a 5400RPM HDD with ~500GB capacity. After installing Windows 7 and about half the drivers (including chipset) I began to doubt whether to go for IDE or AHCI mode for my hard drive. There used to be a lot of discussion on the internet which is better and so far I understood it was particularly helpful on SSDs. Now the general consensus seems to be that AHCI mode is best for most hard drives. I have thus enabled AHCI in the middle of configuring my notebook (rest of the drivers, necessary software etc...) Two questions: considering my HDD's spec above, should I leave it on? Is there any disadvantage of enabling it after Windows 7 and chipset drivers installation? Windows 7 version is 64 bit Home Premium.

  Read the article

• What is a SIP 'Gateway' and how is different from a SIP Proxy/Registrar?

  - by Shrey

  Recently I started looking at SIP implementation for a future work. I was reading (Googling) about what SIP means and how to go about implementing a end-to-end SIP enabled VoIP network. What I did not get is what use does a SIP Gateway is for? How different is it with respect to SIP proxy servers or a SIP DNS/Locator like server? I understand probably QoS would be one primary factor - like dedicating a set bandwidth for SIP/VoIP specific I/O over a network. Anything else? Can anyone help me with any other hints/pointers? I fully understand that is quite a basic question - but I really couldn't find any text which could clear my doubt about what 'Gateway' would mean in SIP context and what differentiates it from other SIP based network components (like Softphones, Proxies etc). Thanks a lot.

  Read the article

• PostgreSQL disaster recovery options

  - by Alex

  My customer has quite a large (the total "data" folder size is 200G) PostgreSQL database and we are working on a disaster recovery plan. We have identified three different types of disasters so far: hardware outage, too much load and unintentional data loss due to erroneously executed bad migration (like DELETE or ALTER TABLE DROP COLUMN). First two types seem to be easy to mitigate but we can't elaborate a good mitigation plan for the third type. I proposed to use ZFS and frequent (hourly) snapshots but "ZFS" means "OpenIndiana" these days and our Ops engineers do not have much expertise in it, so using OpenIndiana imposes another risk. Colleagues try to convince me that restoring from PostgreSQL PITR backup can be as fast as restoring from a ZFS snapshot but I highly doubt that replaying, say, 50G of archived WALs can be considered "fast". What other options are we missing? Is ZFS an only viable alternative? Can we get a fast Pg DB restore time in the Linux environment?

  Read the article

• Huge HDD response time in Resource monitor

  - by Mille

  Just bought all parts for a computer and put it together and installed a fresh version of windows 7. After a while, when using the computer it gets very slow, and even closing down windows can take several minutes. I started to look in the resource monitor and though I found the answer watching my hdd. The thing is that the hdd completes all tests in Seagate's SeaTools for Windows successfully. Which makes me doubt on the problem and weather I can send it in to get an replacement. Suggestions on what it could be and what I can do about it? Here a screenshoot from the resource monitor:

  Read the article

• Can a named (bind) crash make a server unreachable?

  - by giorgio79

  My server recently became unreachable, and after restart a named error was the last line I found in /var/log/messages before restart: Jun 26 00:15:06 host named[1303]: error (network unreachable) resolving 'dlv.isc.org/DNSKEY/IN': 2001:500:71::29#53 Jun 26 06:38:55 host kernel: imklog 5.8.10, log source = /proc/kmsg started. Jun 26 06:38:55 host rsyslogd: [origin software="rsyslogd" swVersion="5.8.10" x-pid="1294" x-info="http://www.rsyslog.com"] start Jun 26 06:38:55 host kernel: Initializing cgroup subsys cpuset Can a named crash make a server unreachable? I doubt it, as I assume I should still be able to login with ssh via IP, but the server did not respond...So, I am trying to make heavy guesses here.

  Read the article

• How can i access windows XP remote desktop on private IP from internet?

  - by Jennie

  So the machine is behind a DSL router on a private IP so that it can not receive inbound requests. I want to know: Is there anyway to setup the router NAT (i highly doubt it supports one to one port mapping) without disturbing other users on the same router. I have another machine on internet which has public IP on it without any firewall. Can i use this machine as a relay server so that to initiate the connection, the XP machine send an outbound request and this relay server makes my connection through and then i can access my machine on pvt ip without any problem. Please tell??

  Read the article

• USB keyboard not working under Windows 7 x64?

  - by Comboo

  I have two USB keyboards, one no-name cheap thing and an old Logitech. When I plug them in to my computer they pop up in Device Manager as an "Unknown device" and "USB-receiver", respectively. Both of them fail to install any drivers, neither automatically or through Windows Update. Both keyboards work perfectly on another computer I have with Windows Vista 32-bit. Can this be one of those cases where a device does not work in a 64-bit version of Windows? I doubt it though since I've never had that problem before with any device and I thought that basic things like keyboards would be kind of failsafe. I don't really know how to start debugging this issue. I've tried all the obvious, rebooting, changing the USB port, etc. Are there any generic x64 keyboard drivers you can use? Is there any way to find the manufacturer of the keyboard over USB? There is nothing written on it.

  Read the article

• Need advice on how to set up live video streaming to web/mobile devices

  - by jasondewitt

  I have a bunch of live udp video streams that currently are viewed by set top boxes in my network. I would like to pick this video up (I can do this with vlc now) and stream it out to other non-STB endpoints (webpage or a phone/tablet of some sort). Right now I am able to pick up the udp stream with vlc and convert it to an http stream on port 8080 of my vlc box. Then I can use the vlc client to pick up and watch that video stream. This is where I'm not sure where to go with it. I really doubt I would want everyone who is watching the video to make a connection back to my vlc server that is doing the encoding, so how do I distribute this live video to the people who want to see it?

  Read the article

• Corrupt Vista Account - With a twist

  - by oldSkool-Soldier

  I have a Windows Vista system whose profile seems to have been corrupted. Many solutions seem to indicate that you create another admin account, log in as that account, and delete the offending profile information for the account that is corrupted. Here's the twist: There are two accounts on this System - 1. Administrator Account 2. Standard Account. It's the Administrator Account which has become corrupted. If you attempted to do any user managment / attempt to create a new account under the 'Standard Account', UAC prompts for a user/pass. It has the admin account come up by default, and asking for a password (of which, there is none). When you click 'OK' - nothing happens (no doubt due to the fact that the account is corrupted, so it can't verify who or what is trying to allow the administrative privilage). Can anyone think of a way of fixing this account, or creating another administrator account to resolve this issue? Many thanks in advance.

  Read the article

• Multiple EyeFinity Display groups

  - by Shinrai

  Is it possible with an EyeFinity enabled card to make multiple display groups at once? I was playing with a FirePro 2460 and while a 4x1 or 2x2 display group works quite nicely, if I make a 2x1 display group and then select one of the other displays to try to make a second 2x1 display group, it disables the first one. Is there any way to circumvent this behavior and set up two separate spans on the same card? Additionally, can you set up distinct display groups if they're on different cards? I will have the opportunity to test several of these cards in one machine very shortly, but I'm curious if anyone has any experience. EDIT: I can confirm that you can make multiple spans on multiple cards (as long as they don't cross cards, obviously) (If the answers are different for FirePro/FireMV cards and Radeon cards, that is helpful and relevant knowledge - I doubt it, though.)

  Read the article

• Is there a way to sharpen low quality images

  - by Saif Bechan

  I have a lot of images for a project that are not really sharp and crisp. I think these were old images that were resized a lot etc. This is because I am working on a website for a client and she does not have the high quality pictures anymore, the pictures I have to work with are somewhat pixelated. Ill show you an example of one I think could be better: Now as you can see the parts around the text 'Azule' is not so sharp. Is there a way to sharpen this. Now I have another one, and I think there is no hope for this one. Is there any hope for the picture above to make it sharp again, I highly doubt it.

  Read the article

• bad switchs duplicate my ip

  - by tacoen

  I had a large area LAN. There were many switch and AP on it, then somehow I couldn't ping my servers, and it's said that the IP was duplicated. I use arpwatch and found out that one of the switch flip-flop-ing the IP. I isolated that troublesome switch using his mac-address. But, since this a large area LAN... I doubt this will be the last cases. If there any software or hardware that I can use to prevent this kind of error? Sorry for my bad English.

  Read the article

• Why can't I record 16khz sampling audio using my laptop?

  - by KayKay

  I want to know why my laptop can't record 16khz sampling audio. The sampling rates I can have using my laptop are higher than 16khz. e.g, 44khz, 48khz, 192khz, and so on... I need to record 16khz sampling audio using my laptop. Sound card in my laptop is Conexant 20671 SmartAudio HD Although I can record 16khz sampling by Sound Forge 8.0, I am doubt whether the recorded audio is really 16khz sampling or not. Because the sound card can't record 16khz sampling, I think there may be some problems on the recording process. Could you give me any hint why the sound card can't record 16khz? and any method to identify whether the recorded audio by Sound Forge 8.0 is really 16khz? Thanks.

  Read the article

• Why are my downloads up to ~1500KByte/sec only, when the ADSL connection locks at 13611Kbit/s?

  - by leladax

  No uploading is going on other than the overhead of downloading which appears to be not high for the abilities of the connection: Only about 30-40KByte/s when the router locks at 1012Kb/s and other direct uploads or uploading overheads can reach more than 100KByte/sec so I don't think it's a congestion at uploading that is doing it. Is there something I miss? Because I assume 13611Kbit/s should be ~1701Kbyte/sec. Is it an overheard at the ADSL level I don't understand? Could it be the ISP doing it? If it's active throttling it can't be on single connections since 2 high speed connections still go up to ~1500KByte/sec. It's not an example on torrents or other complex situations. The tests were on Ethernet, but I doubt the results would be different on wireless. I wonder if the settings of those connections at my end could be doing it, e.g. MTU settings, though I haven't touched the defaults of a common Realtek NIC.

  Read the article

• Free / Cached / Available memory on Linux

  - by pkoraca

  I have read that linux uses free memory for caching, to make system faster. However, both Nagios and Paessler PRTG monitoring system show me that my memory usage is critical. I could change Nagios mem_usage script to sum free and cached memory, but would that be correct information? I doubt that they misunderstood Linux memory usage. Lets say I have 8 GB RAM. 5 GB are used, 2 GB is cached, and I have 1 GB of free memory. Real available memory should be free+cached (3 GB)? If some new application would need additional 3 GB RAM, could it take everything from cache and free without using swap, or is there a minimum that should be in cache? Real example: $ cat /proc/meminfo MemTotal: 5984256 kB MemFree: 137052 kB Buffers: 140484 kB Cached: 3439616 kB SwapCached: 244 kB Active: 3148824 kB Inactive: 2341768 kB ... My monitoring tools show that I have 137 MB free RAM, however I have ~3,5 GB in Cache. Thanks!

  Read the article

• Where can I get a splitter to connect a device with a single 3.5 mm plug into the audio input/output jacks on my laptop?

  - by XinJeisan

  I recently bought the :Hype Retro Handset for Mobile Phone" -- its just a device that looks like a handset to use when chatting on a computer or mobile phone that plugs into the phone/computer with a single 3.5 mm plug. I was hoping to use it on my windows 7 Toshiba laptop. I can hear audio fine through the handset but what I'm saying is not being picked up on the handset. On the box it says "some phones and computers may need additional adapters," so I'm hoping it is possible to get a splitter or something for this to work properly. I did email the parent company (http://dglusa.com/) but I haven't heard from them, and, looking over their website, I doubt I will. I also went to the local radio shack, and the guy said I needed a splitter, but he didn't know where to get one. I can find the kind of splitter I think I need online, but I'm unsure whether they are just for output or can also do input/output.

  Read the article

• wireless dropping out

  - by Sam

  My wireless network connection is dropping out and its driving me nuts. It is weird because it happens at totally random intervals and other devices work while my computer has been dropped. Both my USB dongle and wifi card randomly disconnect from the router and I am unable to connect for a couple of minutes. It is especially irritating because two different adapters are failing at the same time, sounds like a software problem to me, but where? Both my laptop and iPod remain connected when the connection drops. What on earth is happening? I doubt its the router because the other devices would disconnect as well.

  Read the article

• Can a RAID 0 disk be rebuilt

  - by Rogue

  Recently one of the hard drives of one of my RAID 0 configuration gave an error. What do I do now I'm hoping that I can replace that faulty disk with a new hard drive and that the RAID can rebuild itself. (using Intel Matrix Storage Console) Is this possible? Though I doubt it. Is there anyway that I can rebuild the RAID? or have I lost all the matter on it. TECH INFO: I have a software raid on an Intel DG965WH motherboard and the current operating system is Windows

  Read the article

• Can a RAID 0 disk/config be rebuilt ?

  - by Rogue

  Recently one of the hard drives of one of my RAID 0 configuration gave an error. What do I do now I'm hoping that I can replace that faulty disk with a new hard drive and that the RAID can rebuild itself. (using Intel Matrix Storage Console) Is this possible? Though I doubt it. Is there anyway that I can rebuild the RAID? or have I lost all the matter on it. TECH INFO: I have a software raid on an Intel DG965WH motherboard and the current operating system is Windows

  Read the article

• How do I use XQuartz with ssh on OS X?

  - by cwd

  I've downloaded the latest stable version of XQuartz on my Snow Leopard machine, and I'm trying to make an ssh connection with X forwarding but X11 keeps opening. How can I get OS X to use XQuartz? I had X11 installed I downloaded and installed XQuartz X11 is not open / running XQuartz is open and running I try and connect to a remote system using iTerm2: ssh user@remote -X X11 opens. XQuartz is still open, but I doubt it is doing anything. I also tried moving X11 to the trash but then the ssh connection will not complete, even though XQuartz is open. I also get the two warnings which I don't understand how to fix, even after reading the ssh man page. Warning: untrusted X11 forwarding setup failed: xauth key data not generated Warning: No xauth data; using fake authentication data for X11 forwarding.

  Read the article

• Unix: sleep until the specified time

  - by aix

  Is there a (semi-)standard Unix command that would sleep until the time specified on its command line? In other words, I am looking for something similar to sleep that would take wakeup time rather than duration. For example: sleeptill 05:00:00 I can code something up but would rather not re-invent the wheel if there's already something out there. Bonus question: it would be great if it could take the timezone (as in sleeptill 05:00:00 America/New_York). edit Due to the nature of what I am doing, I am looking for a "sleep until T" rather than "run command at T" solution. edit For the avoidance of doubt, if I run the command at 18:00 and tell it to wake up at 17:00, I expect it to sleep for 23 hours (or, in some corner cases having to do with daylight savings time, for 22 or 24 hours.)

  Read the article

• Can the JVM(Oracle) run into an OutOfMemory error if the heap size is below the max?

  - by user439407

  I am running a Tomcat site(with an NGinx front end) that seems to be randomly running out of memory even though the max heap size is pretty large. My question is is it possible for the JVM to get an OutOfMemory error even if the heap size is significantly less than -Xmx? For instance, here is a snapshot I took just 15 seconds before an OutOfMemory error: Tue Dec 18 23:13:28 JST 2012 Free memory: 162.31 MB Total memory: 727.75 MB Max memory: 3808.00 MB I guess theoretically it's possible that my code generated 3 gigs worth of objects in 15 seconds, but I highly doubt it. It seems like the JVM was unable to grow the heap even though it theoretically had room....Is it possible that other processes started using memory to the point that the JVM could not grow? I am running 64-bit Oracle Hotspot on a 64 bit vm running CentOS 5 with 6 gigs of ram.

  Read the article

• Centrally manage Windows 7 computers without Active Directory

  - by Sean W.

  I manage three Windows PCs at home using the principle of least privilege. This means that practically every other day when a new version of Java is released, I have to manually install the update using my administrative credentials on each machine. This is starting to become more work than I had expected. I would love to set up an active directory domain at home, but Microsoft has discontinued Windows home server; its replacement, Windows server 2012 essentials is much more expensive (about $500). Are there any free (preferably as in speech) that would allow me to centrally manage the software installed on each machine in a manner similar to that of active directory? I'd also like to find a way to centrally manage security settings, but I doubt there's an equivalent of group policy. Samba 4 would be an ideal solution, but according to its own developers, it is not yet stable enough for production use.

  Read the article

• Setup Webmail server unable to receive mails

  - by user26516

  I installed centos and configured email server and if I send email goes perfectly but if i reply from email that email i am getting this kind of error. Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the server for the recipient domain example.com by mx00.1and1.com. [74.208.5.3]. I have bought domain in 1and1.com and i successful parked the domain. But i have doubt shall i need to add anything in MX record for other mail server. Please anyone help.

  Read the article

• Windows 2008 server unaccessible without traces in the event log

  - by Rob

  I am trying to figure out why a Windows 2008 server became inaccessible in terms of RDP and access to a web application. The server was turned off and then on. Look at the event log at the time it went offline, I can't find anything. And looking at misc application logs, the system was running like normal after it went offline. It has to be said that by mistake the firewall was switched off earlier, so a lot of attempts had been done to access the SQL Server with the sa user as well as RDP login. But the attempts has been going on for days, so nothing new about that. Besides the event logs, is there anywhere else I can go to examine the cause of this? I am also in doubt whether or not a DOS attack or similar would show up in the event log. From a log for a backup application running on this server I can see that an attempt was done to access a remote IP after the server went offline, but got no connection.

  Read the article

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >