Search Results

Search found 506 results on 21 pages for 'mnt'.

Page 20/21 | < Previous Page | 16 17 18 19 20 21  | Next Page >

• flashcache with mdadm and LVM

  - by Backtogeek

  I am having trouble setting up flashcache on a system with LVM and mdadm, I suspect I am either just missing an obvious step or getting some mapping wrong and hoped someone could point me in the right direction? system info: CentOS 6.4 64 bit mdadm config md0 : active raid1 sdd3[2] sde3[3] sdf3[4] sdg3[5] sdh3[1] sda3[0] 204736 blocks super 1.0 [6/6] [UUUUUU] md2 : active raid6 sdd5[2] sde5[3] sdf5[4] sdg5[5] sdh5[1] sda5[0] 3794905088 blocks super 1.1 level 6, 512k chunk, algorithm 2 [6/6] [UUUUUU] md3 : active raid0 sdc1[1] sdb1[0] 250065920 blocks super 1.1 512k chunks md1 : active raid10 sdh1[1] sda1[0] sdd1[2] sdf1[4] sdg1[5] sde1[3] 76749312 blocks super 1.1 512K chunks 2 near-copies [6/6] [UUUUUU] pcsvan PV /dev/mapper/ssdcache VG Xenvol lvm2 [3.53 TiB / 3.53 TiB free] Total: 1 [3.53 TiB] / in use: 1 [3.53 TiB] / in no VG: 0 [0 ] flashcache create command used: flashcache_create -p back ssdcache /dev/md3 /dev/md2 pvdisplay --- Physical volume --- PV Name /dev/mapper/ssdcache VG Name Xenvol PV Size 3.53 TiB / not usable 106.00 MiB Allocatable yes PE Size 128.00 MiB Total PE 28952 Free PE 28912 Allocated PE 40 PV UUID w0ENVR-EjvO-gAZ8-TQA1-5wYu-ISOk-pJv7LV vgdisplay --- Volume group --- VG Name Xenvol System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 2 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 1 Max PV 0 Cur PV 1 Act PV 1 VG Size 3.53 TiB PE Size 128.00 MiB Total PE 28952 Alloc PE / Size 40 / 5.00 GiB Free PE / Size 28912 / 3.53 TiB VG UUID 7vfKWh-ENPb-P8dV-jVlb-kP0o-1dDd-N8zzYj So that is where I am at, I thought that was the job done however when creating a logical volume called test and mounting it is /mnt/test the sequential write is pathetic, 60 ish MB/s /dev/md3 has 2 x SSD's in Raid0 which alone is performing at around 800 MB/s sequential write and I am trying to cache /dev/md2 which is 6 x 1TB drives in raid6 I have read a number of pages through the day and some of them here, it is obvious from the results that the cache is not functioning but I am unsure why. I have added the filter line in the lvm.conf filter = [ "r|/dev/sdb|", "r|/dev/sdc|", "r|/dev/md3|" ] It is probably something silly but the cache is clearly performing no writes so I suspect I am not mapping it or have not mounted the cache correctly. dmsetup status ssdcache: 0 7589810176 flashcache stats: reads(142), writes(0) read hits(133), read hit percent(93) write hits(0) write hit percent(0) dirty write hits(0) dirty write hit percent(0) replacement(0), write replacement(0) write invalidates(0), read invalidates(0) pending enqueues(0), pending inval(0) metadata dirties(0), metadata cleans(0) metadata batch(0) metadata ssd writes(0) cleanings(0) fallow cleanings(0) no room(0) front merge(0) back merge(0) force_clean_block(0) disk reads(9), disk writes(0) ssd reads(133) ssd writes(9) uncached reads(0), uncached writes(0), uncached IO requeue(0) disk read errors(0), disk write errors(0) ssd read errors(0) ssd write errors(0) uncached sequential reads(0), uncached sequential writes(0) pid_adds(0), pid_dels(0), pid_drops(0) pid_expiry(0) lru hot blocks(31136000), lru warm blocks(31136000) lru promotions(0), lru demotions(0) Xenvol-test: 0 10485760 linear I have included as much info as I can think of, look forward to any replies.

  Read the article

• How to keep group-writeable shares on Samba with OSX clients?

  - by Oliver Salzburg

  I have a FreeNAS server on a network with OSX and Windows clients. When the OSX clients interact with SMB/CIFS shares on the server, they are causing permission problems for all other clients. Update: I can no longer verify any answers because we abandoned the project, but feel free to post any help for future visitors. The details of this behavior seem to also be dependent on the version of OSX the client is running. For this question, let's assume a client running 10.8.2. When I mount the CIFS share on an OSX client and create a new directory on it, the directory will be created with drwxr-x-rx permissions. This is undesirable because it will not allow anyone but me to write to the directory. There are other users in my group which should have write permissions as well. This behavior happens even though the following settings are present in smb.conf on the server: [global] create mask= 0666 directory mask= 0777 [share] force directory mode= 0775 force create mode= 0660 I was under the impression that these settings should make sure that directories are at least created with rwxrwxr-x permissions. But, I guess, that doesn't stop the client from changing the permissions after creating the directory. When I create a folder on the same share from a Windows client, the new folder will have the desired access permissions (rwxrwxrwx), so I'm currently assuming that the problem lies with the OSX client. I guess this wouldn't be such an issue if you could easily change the permissions of the directories you've created, but you can't. When opening the directory info in Finder, I get the old "You have custom access" notice with no ability to make any changes. I'm assuming that this is caused because we're using Windows ACLs on the share, but that's just a wild guess. Changing the write permissions for the group through the terminal works fine, but this is unpractical for the deployment and unreasonable to expect from anyone to do. This is the complete smb.conf: [global] encrypt passwords = yes dns proxy = no strict locking = no read raw = yes write raw = yes oplocks = yes max xmit = 65535 deadtime = 15 display charset = LOCALE max log size = 10 syslog only = yes syslog = 1 load printers = no printing = bsd printcap name = /dev/null disable spoolss = yes smb passwd file = /var/etc/private/smbpasswd private dir = /var/etc/private getwd cache = yes guest account = nobody map to guest = Bad Password obey pam restrictions = Yes # NOTE: read smb.conf. directory name cache size = 0 max protocol = SMB2 netbios name = freenas workgroup = COMPANY server string = FreeNAS Server store dos attributes = yes hostname lookups = yes security = user passdb backend = ldapsam:ldap://ldap.company.local ldap admin dn = cn=admin,dc=company,dc=local ldap suffix = dc=company,dc=local ldap user suffix = ou=Users ldap group suffix = ou=Groups ldap machine suffix = ou=Computers ldap ssl = off ldap replication sleep = 1000 ldap passwd sync = yes #ldap debug level = 1 #ldap debug threshold = 1 ldapsam:trusted = yes idmap uid = 10000-39999 idmap gid = 10000-39999 create mask = 0666 directory mask = 0777 client ntlmv2 auth = yes dos charset = CP437 unix charset = UTF-8 log level = 1 [share] path = /mnt/zfs0 printable = no veto files = /.snap/.windows/.zfs/ writeable = yes browseable = yes inherit owner = no inherit permissions = no vfs objects = zfsacl guest ok = no inherit acls = Yes map archive = No map readonly = no nfs4:mode = special nfs4:acedup = merge nfs4:chown = yes hide dot files force directory mode = 0775 force create mode = 0660

  Read the article

• Why is domU faster than dom0 on IO?

  - by Paco

  I have installed debian 7 on a physical machine. This is the configuration of the machine: 3 hard drives using RAID 5 Strip element size: 1M Read policy: Adaptive read ahead Write policy: Write Through /boot 200 MB ext2 / 15 GB ext3 SWAP 10GB LVM rest (~500GB) emphasized text I installed postgresql, created a big database (over 1GB). I have an SQL request that takes a lot of time to run (a SELECT statement, so it only reads data from the database). This request takes approximately 5.5 seconds to run. Then, I installed XEN, created a domU, with another debian distro. On this OS, I also installed postgresql, with the same database. The same SQL request takes only 2.5 seconds to run. I checked the kernel on both dom0 and domU. uname-a returns "Linux debian 3.2.0-4-amd64 #1 SMP Debian 3.2.41-2+deb7u2 x86_64 GNU/Linux" on both systems. I checked the kernel parameters, which are approximately the same. For those that are relevant, I changed their values to make them match on both systems using sysctl. I saw no changes (the requests still take the same amount of time). After this, I checked the file systems. I used ext3 on domU. Still no changes. I installed hdparm, and ran hdparm -Tt on both systems, on all my partitions on both systems, and I get similar results. Now, I am stuck, I don't know what is different, and what could be the cause of such a big difference. Additional Info: Debian runs on a Dell server PowerEdge 2950 postgresql: 9.1.9 (both dom0 and domU) xen-linux-system: 3.2.0 xen-hypervisor: 4.1 Thanks EDIT: As Krzysztof Ksiezyk suggested, it might be due to some file caching system. I ran the dd command to test both the read and write speed. Here is domU: root@test1:~# dd if=/dev/zero of=/root/dd count=5MB bs=1MB ^C2020+0 records in 2020+0 records out 2020000000 bytes (2.0 GB) copied, 18.8289 s, 107 MB/s root@test1:~# dd if=/root/dd of=/dev/null count=5MB bs=1MB 2020+0 records in 2020+0 records out 2020000000 bytes (2.0 GB) copied, 15.0549 s, 134 MB/s And here is dom0: root@debian:~# dd if=/dev/zero of=/root/dd count=5MB bs=1MB ^C1693+0 records in 1693+0 records out 1693000000 bytes (1.7 GB) copied, 8.87281 s, 191 MB/s root@debian:~# dd if=/root/dd of=/dev/null count=5MB bs=1MB 1693+0 records in 1693+0 records out 1693000000 bytes (1.7 GB) copied, 0.501509 s, 3.4 GB/s What can be the cause of this caching system? And how can we "fix" it? Can we apply it to dom0? EDIT 2: I switched my virtual disk type. To do so I followed this article. I did a dd if=/dev/vg0/test1-disk of=/mnt/test1-disk.img bs=16M Then in /etc/xen/test1.cfg, I changed the disk parameter to use file: instead of phy: it should have removed the file caching, but I still get the same numbers (domU being much faster for Postgres)

  Read the article

• Weird nfs performance: 1 thread better than 8, 8 better than 2!

  - by Joe

  I'm trying to determine the cause of poor nfs performance between two Xen Virtual Machines (client & server) running on the same host. Specifically, the speed at which I can sequentially read a 1GB file on the client is much lower than what would be expected based on the measured network connection speed between the two VMs and the measured speed of reading the file directly on the server. The VMs are running Ubuntu 9.04 and the server is using the nfs-kernel-server package. According to various NFS tuning resources, changing the number of nfsd threads (in my case kernel threads) can affect performance. Usually this advice is framed in terms of increasing the number from the default of 8 on heavily-used servers. What I find in my current configuration: RPCNFSDCOUNT=8: (default): 13.5-30 seconds to cat a 1GB file on the client so 35-80MB/sec RPCNFSDCOUNT=16: 18s to cat the file 60MB/s RPCNFSDCOUNT=1: 8-9 seconds to cat the file (!!?!) 125MB/s RPCNFSDCOUNT=2: 87s to cat the file 12MB/s I should mention that the file I'm exporting is on a RevoDrive SSD mounted on the server using Xen's PCI-passthrough; on the server I can cat the file in under seconds ( 250MB/s). I am dropping caches on the client before each test. I don't really want to leave the server configured with just one thread as I'm guessing that won't work so well when there are multiple clients, but I might be misunderstanding how that works. I have repeated the tests a few times (changing the server config in between) and the results are fairly consistent. So my question is: why is the best performance with 1 thread? A few other things I have tried changing, to little or no effect: increasing the values of /proc/sys/net/ipv4/ipfrag_low_thresh and /proc/sys/net/ipv4/ipfrag_high_thresh to 512K, 1M from the default 192K,256K increasing the value of /proc/sys/net/core/rmem_default and /proc/sys/net/core/rmem_max to 1M from the default of 128K mounting with client options rsize=32768, wsize=32768 From the output of sar -d I understand that the actual read sizes going to the underlying device are rather small (<100 bytes) but this doesn't cause a problem when reading the file locally on the client. The RevoDrive actually exposes two "SATA" devices /dev/sda and /dev/sdb, then dmraid picks up a fakeRAID-0 striped across them which I have mounted to /mnt/ssd and then bind-mounted to /export/ssd. I've done local tests on my file using both locations and see the good performance mentioned above. If answers/comments ask for more details I will add them.

  Read the article

• Exalogic 2.0.1 Tea Break Snippets - Modifying the Default Shipped Template

  - by The Old Toxophilist

  Having installed your Exalogic Virtual environment by default you have a single template which can be used to create your vServers. Although this template is suitable for creating simple test or development vServers it is recommended that you look at creating your own custom vServers that match the environment you wish to build and deploy. Therefore this Tea Time Snippet will take you through the simple process of modifying the standard template. Before You Start To edit the template you will need the Oracle ModifyJeos Utility which can be downloaded from the eDelivery Site. Once the ModifyJeos Utility has been downloaded we can install the rpms onto either an existing vServer or one of the Control vServers. rpm -ivh ovm-modify-jeos-1.0.1-10.el5.noarch.rpm rpm -ivh ovm-template-config-1.0.1-5.el5.noarch.rpm Alternatively you can install the modify jeos packages on a none Exalogic OEL installation or a VirtualBox image. If you are doing this, assuming OEL 5u8, you will need the following rpms. rpm -ivh ovm-modify-jeos-1.0.1-10.el5.noarch.rpm rpm -ivh ovm-el5u2-xvm-jeos-1.0.1-5.el5.i386.rpm rpm -ivh ovm-template-config-1.0.1-5.el5.noarch.rpm Base Template If you have installed the modify onto a vServer running on the Exalogic then simply mount the /export/common/images from the ZFS storage and you will be able to find the el_x2-2_base_linux_guest_vm_template_2.0.1.1.0_64.tgz (or similar depending which version you have) template file. Alternatively the latest can be downloaded from the eDelivery Site. Now we have the Template tgz we will need the extract it as follows: tar -zxvf  el_x2-2_base_linux_guest_vm_template_2.0.1.1.0_64.tgz This will create a directory called BASE which will contain the System.img (VServer image) and vm.cfg (VServer Config information). This directory should be renamed to something more meaning full that indicates what we have done to the template and then the Simple name / name in the vm.cfg editted for the same reason. Modifying the Template Resizing Root File System By default the shipped template has a root size of 4 GB which will leave a vServer created from it running at 90% full on the root disk. We can simply resize the template by executing the following: modifyjeos -f System.img -T <New Size MB>) For example to imcrease the default 4 GB to 40 GB we would execute: modifyjeos -f System.img -T 40960) Resizing Swap We can modify the size of the swap space within a template by executing the following: modifyjeos -f System.img -S <New Size MB>) For example to increase the swap from the default 512 MB to 4 GB we would execute: modifyjeos -f System.img -S 4096) Changing RPMs Adding RPMs To add RPMs using modifyjeos, complete the following steps: Add the names of the new RPMs in a list file, such as addrpms.lst. In this file, you should list each new RPM in a separate line. Ensure that all of the new RPMs are in a single directory, such as rpms. Run the following command to add the new RPMs: modifyjeos -f System.img -a <path_to_addrpms.lst> -m <path_to_rpms> -nogpg Where <path_to_addrpms.lst> is the path to the location of the addrpms.lst file, and <path_to_rpms> is the path to the directory that contains the RPMs. The -nogpg option eliminates signature check on the RPMs. Removing RPMs To remove RPM s using modifyjeos, complete the following steps: Add the names of the RPMs (the ones you want to remove) in a list file, such as removerpms.lst. In this file, you should list each RPM in a separate line. The Oracle Exalogic Elastic Cloud Administrator's Guide provides a list of all RPMs that must not be removed from the vServer. Run the following command to remove the RPMs: modifyjeos -f System.img -e <path_to_removerpms.lst> Where <path_to_removerpms.lst> is the path to the location of the removerpms.lst file. Mounting the System.img For all other modifications that are not supported by the modifyjeos command (adding you custom yum repositories, pre configuring NTP, modify default NFSv4 Nobody functionality, etc) we can mount the System.img and access it directly. To facititate quick and easy mounting/unmounting of the System.img I have put together the simple scripts below. MountSystemImg.sh #!/bin/sh # The script assumes it's being run from the directory containing the System.img # Export for later i.e. during unmount export LOOP=`losetup -f` export SYSTEMIMG=/mnt/elsystem # Make Temp Mount Directory mkdir -p $SYSTEMIMG # Create Loop for the System Image losetup $LOOP System.img kpartx -a $LOOP mount /dev/mapper/`basename $LOOP`p2 $SYSTEMIMG #Change Dir into mounted Image cd $SYSTEMIMG UnmountSystemImg.sh #!/bin/sh # The script assumes it's being run from the directory containing the System.img # Assume the $LOOP & $SYSTEMIMG exist from a previous run on the MountSystemImg.sh umount $SYSTEMIMG kpartx -d $LOOP losetup -d $LOOP Packaging the Template Once you have finished modifying the template it can be simply repackaged and then imported into EMOC as described in "Exalogic 2.0.1 Tea Break Snippets - Importing Public Server Template". To do this we will simply cd to the directory above that containing the modified files and execute the following: tar -zcvf <New Template Directory> <New Template Name>.tgz The resulting.tgz file can be copied to the images directory on the ZFS and uploadd using the IB network. This entry was originally posted on the The Old Toxophilist Site.

  Read the article

• mounting ext4 fs with block size of 65536

  - by seaquest

  I am doing some benchmarking on EXT4 performance on Compact Flash media. I have created an ext4 fs with block size of 65536. however I can not mount it on ubuntu-10.10-netbook-i386. (it is already mounting ext4 fs with 4096 bytes of block sizes) According to my readings on ext4 it should allow such big block sized fs. I want to hear your comments. root@ubuntu:~# mkfs.ext4 -b 65536 /dev/sda3 Warning: blocksize 65536 not usable on most systems. mke2fs 1.41.12 (17-May-2010) mkfs.ext4: 65536-byte blocks too big for system (max 4096) Proceed anyway? (y,n) y Warning: 65536-byte blocks too big for system (max 4096), forced to continue Filesystem label= OS type: Linux Block size=65536 (log=6) Fragment size=65536 (log=6) Stride=0 blocks, Stripe width=0 blocks 19968 inodes, 19830 blocks 991 blocks (5.00%) reserved for the super user First data block=0 1 block group 65528 blocks per group, 65528 fragments per group 19968 inodes per group Writing inode tables: done Creating journal (1024 blocks): done Writing superblocks and filesystem accounting information: done This filesystem will be automatically checked every 37 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override. root@ubuntu:~# tune2fs -l /dev/sda3 tune2fs 1.41.12 (17-May-2010) Filesystem volume name: <none> Last mounted on: <not available> Filesystem UUID: 4cf3f507-e7b4-463c-be11-5b408097099b Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal ext_attr resize_inode dir_index filetype extent flex_bg sparse_super large_file huge_file uninit_bg dir_nlink extra_isize Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 19968 Block count: 19830 Reserved block count: 991 Free blocks: 18720 Free inodes: 19957 First block: 0 Block size: 65536 Fragment size: 65536 Blocks per group: 65528 Fragments per group: 65528 Inodes per group: 19968 Inode blocks per group: 78 Flex block group size: 16 Filesystem created: Sat Feb 5 14:39:55 2011 Last mount time: n/a Last write time: Sat Feb 5 14:40:02 2011 Mount count: 0 Maximum mount count: 37 Last checked: Sat Feb 5 14:39:55 2011 Check interval: 15552000 (6 months) Next check after: Thu Aug 4 14:39:55 2011 Lifetime writes: 70 MB Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: afb5b570-9d47-4786-bad2-4aacb3b73516 Journal backup: inode blocks root@ubuntu:~# mount -t ext4 /dev/sda3 /mnt/ mount: wrong fs type, bad option, bad superblock on /dev/sda3, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so

  Read the article

• Huawei b153 limit of devices

  - by bdecaf

  I set up my home network all through this 3G wifi router. Problem is it only allows 5 devices to connect. That's not much especially if a wifi printer and gaming consoles keep hogging these slots. On the other hand I don't see the point on blocking these devices. They are (should) not doing anything online just intern in my network. The documentation I can find is surpirisingly unhelpful and focuses how to plug the device in a power socket. So what would be my options. Notes: I have already been able to get a shell on the device using ssh. It's running some Busybox. But I fail to find the how and where this limit is enforced/created. Notes 2: Specifically my device is a 3WebCube - unfortunately not specifically marked with the Huawei Model number. Successes so far After enabling ssh in the options I can login: ssh -T [email protected] [email protected]'s password: ------------------------------- -----Welcome to ATP Cli------ ------------------------------- unfortunately because of this -T - the tab key does not work for autocomplete and all inputted commands will be echoed. Also no history with arrow keys. ATP interface this custom interface is not very useful: ATP>help help Welcome to ATP command line tool. If any question, please input "?" at the end of command. ATP>? ? cls debug help save ? exit ATP>save? save? Command failed. ATP>save ? save ? ATP>debug ? debug ? display set trace ? Shell BUT undocumented - I somehow found on a auto translated chinese website - all you need to do is input sh ATP>sh sh BusyBox vv1.9.1 (2011-03-27 11:59:11 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. # builtin commands # help Built-in commands: ------------------- . : alias bg break cd chdir command continue eval exec exit export false fg getopts hash help jobs kill let local pwd read readonly return set shift source times trap true type ulimit umask unalias unset wait shows standard unix structure: # ls / var tmp proc linuxrc init etc bin usr sbin mnt lib html dev in /bin # ls /bin zebra strace ppps ln echo cat wscd startbsp pppc klog ebtables busybox wlancmd sshd ping kill dns brctl web sntp netstat iwpriv dhcps auth usbdiagd sms mount iwcontrol dhcpc atserver upnp sleep mknod iptables date atcmd upg siproxd mkdir ipcheck cp at umount sh mini_upnpd ip console ash test_at rm mic igmpproxy cms telnetd ripd ls ethcmd cmgr swapdev ps log equipcmd cli in /sbin # ls /sbin vconfig reboot insmod ifconfig arp route poweroff init halt using tftp after installing tftp on my desktop I was able to send files with tftp -s -l curcfg.xml 192.168.1.103 and to download onto the huawei with tftp -g -r curcfg.xml 192.168.1.103 I think I'll need that - because I don't see any editor installed. readout stuff (still playing around where I would get interesting info) For confirmation of hardware: # cat /var/log/modem_hardware_name ^HWVER:"WL1B153M001"# # cat /var/log/modem_software_name 1096.11.03.02.107 # cat /var/log/product_name B153

  Read the article

• Where's the Swap File/Partition?

  - by chrisbunney

  I'm investigating the virtual memory configuration of a Debian based Amazon EC2 instance, and as my background isn't in system admin, I'm slightly confused by what I'm seeing. We're using MongoDB, and the monitoring server we have indicates that the Mongo process is using about 20GB of swap space, however I can't figure out where this is located on the server. As far as I can tell from using the various suggested methods from Google, there is either a much smaller amount, or none at all. top indicates that there is 1.8GB of swap memory: top - 15:35:21 up 6 days, 3:23, 1 user, load average: 1.60, 1.43, 1.37 Tasks: 47 total, 2 running, 45 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 1.3%sy, 0.0%ni, 14.7%id, 83.8%wa, 0.0%hi, 0.0%si, 0.1%st Mem: 3928924k total, 2855572k used, 1073352k free, 640564k buffers Swap: 0k total, 0k used, 0k free, 1887788k cached swapon -s doesn't seem to think there's any swap space: Filename Type Size Used Priority free -m doesn't think there's any swap either: total used free shared buffers cached Mem: 3836 3663 172 0 626 2701 -/+ buffers/cache: 336 3500 Swap: 0 0 0 And neither does vmstat: procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 3 0 66224 641372 2874744 0 0 21 5012 21 33 2 2 76 19 But cat /etc/fstab thinks there is a swap partition: /dev/xvda1 / ext3 defaults 1 1 /dev/xvda2 /mnt ext3 defaults 0 0 /dev/xvda3 swap swap defaults 0 0 none /proc proc defaults 0 0 none /sys sysfs defaults 0 0 However df -k gives no indication of the xvda3 partition: Filesystem 1K-blocks Used Available Use% Mounted on /dev/xvda1 16513960 15675324 0 100% / tmpfs 1964460 8 1964452 1% /lib/init/rw udev 1914148 28 1914120 1% /dev tmpfs 1964460 4 1964456 1% /dev/shm So I really don't know what to make of this, because I appear to have a process using about 10 times more virtual memory than what might be available, and I have no idea where this virtual memory is on the system. I'm probably misinterpreting the output of the tools, so I'd be grateful if someone would be able to set me straight: What have I got wrong, what's the right interpretation, and how do you reach that interpretation? EDIT0: We use 10gen's MMS for monitoring the database, the relevant section for memory from the last data point is: "mem": { "virtual": 20749, "bits": 64, "supported": true, "mappedWithJournal": 20376, "mapped": 10188, "resident": 1219 }, This JSON is specific to the database process (I believe) rather than the system as a whole. fdisk -l /dev/xvda outputs... nothing? I tried each of the 3 xvda entries in /etc/fstab as well: root@ip:~# fdisk -l /dev/xvda1 Disk /dev/xvda1: 34.4 GB, 34359738368 bytes 255 heads, 63 sectors/track, 4177 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/xvda1 doesn't contain a valid partition table root@ip:~# fdisk -l /dev/xvda2 root@ip:~# fdisk -l /dev/xvda3 root@ip:~# Edit1: Output of cat /proc/meminfo for the sake of completeness: MemTotal: 3928924 kB MemFree: 726600 kB Buffers: 648368 kB Cached: 2216556 kB SwapCached: 0 kB Active: 1945100 kB Inactive: 994016 kB Active(anon): 60476 kB Inactive(anon): 12952 kB Active(file): 1884624 kB Inactive(file): 981064 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 387180 kB Writeback: 0 kB AnonPages: 73380 kB Mapped: 1188260 kB Shmem: 48 kB Slab: 149768 kB SReclaimable: 146076 kB SUnreclaim: 3692 kB KernelStack: 1104 kB PageTables: 16096 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 1964460 kB Committed_AS: 305572 kB VmallocTotal: 34359738367 kB VmallocUsed: 16760 kB VmallocChunk: 34359721448 kB HardwareCorrupted: 0 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 3932160 kB DirectMap2M: 0 kB

  Read the article

• No device file for partition on logical volume (Linux LVM)

  - by Brian

  I created a logical volume (scandata) containing a single ext3 partition. It is the only logical volume in its volume group (case4t). Said volume group is comprised by 3 physical volumes, which are three primary partitions on a single block device (/dev/sdb). When I created it, I could mount the partition via the block device /dev/mapper/case4t-scandatap1. Since last reboot the aforementioned block device file has disappeared. It may be of note -- I'm not sure -- that my superior (a college professor) had prompted this reboot by running sudo chmod -R [his name] /usr/bin, which obliterated all suid in its path, preventing the both of us from sudo-ing. That issue has been (temporarily) rectified via this operation. Now I'll cut the chatter and get started with the terminal dumps: $ sudo pvs; sudo vgs; sudo lvs Logging initialised at Sat Jan 8 11:42:34 2011 Set umask to 0077 Scanning for physical volume names PV VG Fmt Attr PSize PFree /dev/sdb1 case4t lvm2 a- 819.32G 0 /dev/sdb2 case4t lvm2 a- 866.40G 0 /dev/sdb3 case4t lvm2 a- 47.09G 0 Wiping internal VG cache Logging initialised at Sat Jan 8 11:42:34 2011 Set umask to 0077 Finding all volume groups Finding volume group "case4t" VG #PV #LV #SN Attr VSize VFree case4t 3 1 0 wz--n- 1.69T 0 Wiping internal VG cache Logging initialised at Sat Jan 8 11:42:34 2011 Set umask to 0077 Finding all logical volumes LV VG Attr LSize Origin Snap% Move Log Copy% Convert scandata case4t -wi-a- 1.69T Wiping internal VG cache $ sudo vgchange -a y Logging initialised at Sat Jan 8 11:43:14 2011 Set umask to 0077 Finding all volume groups Finding volume group "case4t" 1 logical volume(s) in volume group "case4t" already active 1 existing logical volume(s) in volume group "case4t" monitored Found volume group "case4t" Activated logical volumes in volume group "case4t" 1 logical volume(s) in volume group "case4t" now active Wiping internal VG cache $ ls /dev | grep case4t case4t $ ls /dev/mapper case4t-scandata control $ sudo fdisk -l /dev/case4t/scandata Disk /dev/case4t/scandata: 1860.5 GB, 1860584865792 bytes 255 heads, 63 sectors/track, 226203 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00049bf5 Device Boot Start End Blocks Id System /dev/case4t/scandata1 1 226203 1816975566 83 Linux $ sudo parted /dev/case4t/scandata print Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/case4t-scandata: 1861GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 1861GB 1861GB primary ext3 $ sudo fdisk -l /dev/sdb Disk /dev/sdb: 1860.5 GB, 1860593254400 bytes 255 heads, 63 sectors/track, 226204 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000081 Device Boot Start End Blocks Id System /dev/sdb1 1 106955 859116006 83 Linux /dev/sdb2 113103 226204 908491815 83 Linux /dev/sdb3 106956 113102 49375777+ 83 Linux Partition table entries are not in disk order $ sudo parted /dev/sdb print Model: DELL PERC 6/i (scsi) Disk /dev/sdb: 1861GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 880GB 880GB primary reiserfs 3 880GB 930GB 50.6GB primary 2 930GB 1861GB 930GB primary I find it a bit strange that partition one above is said to be reiserfs, or if it matters -- it was previously reiserfs, but LVM recognizes it as a PV. To reiterate, neither /dev/mapper/case4t-scandatap1 (which I had used previously) nor /dev/case4t/scandata1 (as printed by fdisk) exists. And /dev/case4t/scandata (no partition number) cannot be mounted: $sudo mount -t ext3 /dev/case4t/scandata /mnt/new mount: wrong fs type, bad option, bad superblock on /dev/mapper/case4t-scandata, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so All I get on syslog is: [170059.538137] VFS: Can't find ext3 filesystem on dev dm-0. Thanks in advance for any help you can offer, Brian P.S. I am on Ubuntu GNU/Linux 2.6.28-11-server (Jaunty) (out of date, I know -- that's on the laundry list).

  Read the article

• NFS Mounts Issues

  - by user554005

  Having some issue with a NFS Setup on the clients it just times out refuses to connect [root@host9 ~]# mount 192.168.0.17:/home/export /mnt/export mount: mount to NFS server '192.168.0.17' failed: timed out (retrying). mount: mount to NFS server '192.168.0.17' failed: timed out (retrying). mount: mount to NFS server '192.168.0.17' failed: timed out (retrying). mount: mount to NFS server '192.168.0.17' failed: timed out (retrying). Here are the settings I'm using: [root@host17 /home/export]# cat /etc/hosts.allow # # hosts.allow This file contains access rules which are used to # allow or deny connections to network services that # either use the tcp_wrappers library or that have been # started through a tcp_wrappers-enabled xinetd. # # See 'man 5 hosts_options' and 'man 5 hosts_access' # for information on rule syntax. # See 'man tcpd' for information on tcp_wrappers # portmap: 192.168.0.0/255.255.255.0 lockd: 192.168.0.0/255.255.255.0 rquotad: 192.168.0.0/255.255.255.0 mountd: 192.168.0.0/255.255.255.0 statd: 192.168.0.0/255.255.255.0 [root@host17 /home/export]# cat /etc/hosts.deny # # hosts.deny This file contains access rules which are used to # deny connections to network services that either use # the tcp_wrappers library or that have been # started through a tcp_wrappers-enabled xinetd. # # The rules in this file can also be set up in # /etc/hosts.allow with a 'deny' option instead. # # See 'man 5 hosts_options' and 'man 5 hosts_access' # for information on rule syntax. # See 'man tcpd' for information on tcp_wrappers # portmap:ALL lockd:ALL mountd:ALL rquotad:ALL statd:ALL [root@host17 /home/export]# cat /etc/exports /home/export 192.168.0.0/255.255.255.0(rw) [root@host17 /home/export]# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination RH-Firewall-1-INPUT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination RH-Firewall-1-INPUT all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain RH-Firewall-1-INPUT (2 references) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT icmp -- anywhere anywhere icmp any ACCEPT esp -- anywhere anywhere ACCEPT ah -- anywhere anywhere ACCEPT udp -- anywhere 224.0.0.251 udp dpt:mdns ACCEPT udp -- anywhere anywhere udp dpt:ipp ACCEPT tcp -- anywhere anywhere tcp dpt:ipp ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:http ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:https ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:6379 ACCEPT udp -- 192.168.0.0/24 anywhere state NEW udp dpt:sunrpc ACCEPT tcp -- 192.168.0.0/24 anywhere state NEW tcp dpt:sunrpc ACCEPT tcp -- 192.168.0.0/24 anywhere state NEW tcp dpt:nfs ACCEPT tcp -- 192.168.0.0/24 anywhere state NEW tcp dpt:32803 ACCEPT udp -- 192.168.0.0/24 anywhere state NEW udp dpt:filenet-rpc ACCEPT tcp -- 192.168.0.0/24 anywhere state NEW tcp dpt:892 ACCEPT udp -- 192.168.0.0/24 anywhere state NEW udp dpt:892 ACCEPT tcp -- 192.168.0.0/24 anywhere state NEW tcp dpt:rquotad ACCEPT udp -- 192.168.0.0/24 anywhere state NEW udp dpt:rquotad ACCEPT tcp -- 192.168.0.0/24 anywhere state NEW tcp dpt:pftp ACCEPT udp -- 192.168.0.0/24 anywhere state NEW udp dpt:pftp REJECT all -- anywhere anywhere reject-with icmp-host-prohibited on the clients here is some rpcinfos [root@host9 ~]# rpcinfo -p 192.168.0.17 program vers proto port 100000 4 tcp 111 portmapper 100000 3 tcp 111 portmapper 100000 2 tcp 111 portmapper 100000 4 udp 111 portmapper 100000 3 udp 111 portmapper 100000 2 udp 111 portmapper 100011 1 udp 875 rquotad 100011 2 udp 875 rquotad 100011 1 tcp 875 rquotad 100011 2 tcp 875 rquotad 100005 1 udp 45857 mountd 100005 1 tcp 55772 mountd 100005 2 udp 34021 mountd 100005 2 tcp 59542 mountd 100005 3 udp 60930 mountd 100005 3 tcp 53086 mountd 100003 2 udp 2049 nfs 100003 3 udp 2049 nfs 100003 4 udp 2049 nfs 100227 2 udp 2049 nfs_acl 100227 3 udp 2049 nfs_acl 100003 2 tcp 2049 nfs 100003 3 tcp 2049 nfs 100003 4 tcp 2049 nfs 100227 2 tcp 2049 nfs_acl 100227 3 tcp 2049 nfs_acl 100021 1 udp 59832 nlockmgr 100021 3 udp 59832 nlockmgr 100021 4 udp 59832 nlockmgr 100021 1 tcp 36140 nlockmgr 100021 3 tcp 36140 nlockmgr 100021 4 tcp 36140 nlockmgr 100024 1 udp 46494 status 100024 1 tcp 49672 status [root@host9 ~]# [root@host9 ~]# rpcinfo -u 192.168.0.17 nfs rpcinfo: RPC: Timed out program 100003 version 0 is not available [root@host9 ~]# rpcinfo -u 192.168.0.17 portmap program 100000 version 2 ready and waiting program 100000 version 3 ready and waiting program 100000 version 4 ready and waiting [root@host9 ~]# rpcinfo -u 192.168.0.17 mount rpcinfo: RPC: Timed out program 100005 version 0 is not available [root@host9 ~]# I'm running CentOS 5.8 on all systems

  Read the article

• reiserfsck on lvm

  - by DaDaDom

  It seems like my filesystem got corrupted somehow during the last reboot of my server. I can't fsck some logical volumes anymore. The setup: root@rescue ~ # cat /mnt/rescue/etc/fstab proc /proc proc defaults 0 0 /dev/md0 /boot ext3 defaults 0 2 /dev/md1 / ext3 defaults,errors=remount-ro 0 1 /dev/systemlvm/home /home reiserfs defaults 0 0 /dev/systemlvm/usr /usr reiserfs defaults 0 0 /dev/systemlvm/var /var reiserfs defaults 0 0 /dev/systemlvm/tmp /tmp reiserfs noexec,nosuid 0 2 /dev/sda5 none swap defaults,pri=1 0 0 /dev/sdb5 none swap defaults,pri=1 0 0 [UPDATE] First question: what "part" should I check for bad blocks? The logical volume, the underlying /dev/md or the /dev/sdx below that? Is doing what I am doing the right way to go? [/UPDATE] The errormessage when checking /dev/systemlvm/usr: root@rescue ~ # reiserfsck /dev/systemlvm/usr reiserfsck 3.6.19 (2003 www.namesys.com) [...] Will read-only check consistency of the filesystem on /dev/systemlvm/usr Will put log info to 'stdout' Do you want to run this program?[N/Yes] (note need to type Yes if you do):Yes ########### reiserfsck --check started at Wed Feb 3 07:10:55 2010 ########### Replaying journal.. Reiserfs journal '/dev/systemlvm/usr' in blocks [18..8211]: 0 transactions replayed Checking internal tree.. Bad root block 0. (--rebuild-tree did not complete) Aborted Well so far, let's try --rebuild-tree: root@rescue ~ # reiserfsck --rebuild-tree /dev/systemlvm/usr reiserfsck 3.6.19 (2003 www.namesys.com) [...] Will rebuild the filesystem (/dev/systemlvm/usr) tree Will put log info to 'stdout' Do you want to run this program?[N/Yes] (note need to type Yes if you do):Yes Replaying journal.. Reiserfs journal '/dev/systemlvm/usr' in blocks [18..8211]: 0 transactions replayed ########### reiserfsck --rebuild-tree started at Wed Feb 3 07:12:27 2010 ########### Pass 0: ####### Pass 0 ####### Loading on-disk bitmap .. ok, 269716 blocks marked used Skipping 8250 blocks (super block, journal, bitmaps) 261466 blocks will be read 0%....20%....40%....60%....80%....100% left 0, 11368 /sec 52919 directory entries were hashed with "r5" hash. "r5" hash is selected Flushing..finished Read blocks (but not data blocks) 261466 Leaves among those 13086 Objectids found 53697 Pass 1 (will try to insert 13086 leaves): ####### Pass 1 ####### Looking for allocable blocks .. finished 0% left 12675, 0 /sec The problem has occurred looks like a hardware problem (perhaps memory). Send us the bug report only if the second run dies at the same place with the same block number. mark_block_used: (39508) used already Aborted Bad. But let's do it again as mentioned: [...] Flushing..finished Read blocks (but not data blocks) 261466 Leaves among those 13085 Objectids found 54305 Pass 1 (will try to insert 13085 leaves): ####### Pass 1 ####### Looking for allocable blocks .. finished 0%... left 12127, 958 /sec The problem has occurred looks like a hardware problem (perhaps memory). Send us the bug report only if the second run dies at the same place with the same block number. build_the_tree: Nothing but leaves are expected. Block 196736 - internal Aborted Same happens every time, only the actual error message changes. Sometimes I get mark_block_used: (somenumber) used already, other times the block number changes. Seems like something is REALLY broken. Are there any chances I can somehow get the partitions to work again? It's a server to which I don't have physical access directly (hosted server). Thanks in advance!

  Read the article

• How to restore Linode to Vagrant VM?

  - by Iain Elder

  I'm trying to set up a Linux development environment so I can safely make changes to my website without breaking the live site. Linode hosts my live site. A simple solution would be to host my development server on Linode as well, but I want to avoid doubling my hosting costs. The cheapest way I see is to use Vagrant on my Windows workstation to host my development environment. After I attempt to restore the backup to Vagrant and reboot the VM, I can no longer ssh into the Vagrant host. It's probably because by restoring the backup I overwrite some special Vagrant configuration, but I'm not sure how to avoid that. How do I make this approach work? If my approach is fundamentally wrong, can you suggest an alternative? Creating the backup On the Linode I used these commands to create a compressed copy of the entire filesystem, while ignoring things that shouldn't be included in the backup: $ sudo rsync -ahvz --exclude={/dev/*,/proc/*,/sys/*,/tmp/*,/run/*,/mnt/*,/backup/*} /* /backup/2 $ sudo tar -czf /backup/2.gz /backup/2 The backup file is called 2.gz because this is thesecond backup. The first backup is called 1.gz. I use WinSCP to copy the backup file to my Windows workstation. Setting up the Vagrant host I need a Vagrant box that matches my Linode operating system (Ubuntu 12.04.3 LTS, kernel 3.9.3). I selected the closet match from vagrantbox.es: Ubuntu Server Precise 12.04.3 amd64 Kernel is ready for Docker (Docker not included) On my workstation I ran these commands to add the box and initialize and boot an instance: $ vagrant box add ubuntu-precise http://nitron-vagrant.s3-website-us-east-1.amazonaws.com/vagrant_ubuntu_12.04.3_amd64_virtualbox.box $ mkdir linode-test $ cd linode-test $ vagrant init ubuntu-precise $ vagrant up Now Vagrant is running a machine with SSH on port 2222. The operating system version is the same. The kernel version is 3.8.0. Sounds close enough. Restoring the backup With WinSCP I copied the backup file 2.gz to /home/vagrant/2.gz on the Vagrant box. With PuTTY I connected via ssh to my new Vagrant box: On the box move the backup to the filesystem root. $ sudo mv 2.gz / Extract the archive to the filesystem root: $ sudo tar -xvpz -f 2.gz -C / --strip-components=2 (I discovered I need to use strip components because all files in the archive have the prefix backup/2/. I'll fix this for the next backup.) After the tar command completes, I log out of the box. Testing the backup When I try to log in again, it doesn't let me log in as vagrant with a password any more. It does let me log in as iain, my user on the live Linode, with a password. That surprised me because I disabled password authentication on my live Linode. I figured that I have to restart the ssh service for the change to take effect. Instead of restarting just ssh, I chose to restart the whole system. Now I can't even get to the login screen. PuTTY says "connection refused" when I try to connect. What went wrong?

  Read the article

• RHCS: GFS2 in A/A cluster with common storage. Configuring GFS with rgmanager

  - by Pavel A

  I'm configuring a two node A/A cluster with a common storage attached via iSCSI, which uses GFS2 on top of clustered LVM. So far I have prepared a simple configuration, but am not sure which is the right way to configure gfs resource. Here is the rm section of /etc/cluster/cluster.conf: <rm> <failoverdomains> <failoverdomain name="node1" nofailback="0" ordered="0" restricted="1"> <failoverdomainnode name="rhc-n1"/> </failoverdomain> <failoverdomain name="node2" nofailback="0" ordered="0" restricted="1"> <failoverdomainnode name="rhc-n2"/> </failoverdomain> </failoverdomains> <resources> <script file="/etc/init.d/clvm" name="clvmd"/> <clusterfs name="gfs" fstype="gfs2" mountpoint="/mnt/gfs" device="/dev/vg-cs/lv-gfs"/> </resources> <service name="shared-storage-inst1" autostart="0" domain="node1" exclusive="0" recovery="restart"> <script ref="clvmd"> <clusterfs ref="gfs"/> </script> </service> <service name="shared-storage-inst2" autostart="0" domain="node2" exclusive="0" recovery="restart"> <script ref="clvmd"> <clusterfs ref="gfs"/> </script> </service> </rm> This is what I mean: when using clusterfs resource agent to handle GFS partition, it is not unmounted by default (unless force_unmount option is given). This way when I issue clusvcadm -s shared-storage-inst1 clvm is stopped, but GFS is not unmounted, so a node cannot alter LVM structure on shared storage anymore, but can still access data. And even though a node can do it quite safely (dlm is still running), this seems to be rather inappropriate to me, since clustat reports that the service on a particular node is stopped. Moreover if I later try to stop cman on that node, it will find a dlm locking, produced by GFS, and fail to stop. I could have simply added force_unmount="1", but I would like to know what is the reason behind the default behavior. Why is it not unmounted? Most of the examples out there silently use force_unmount="0", some don't, but none of them give any clue on how the decision was made. Apart from that I have found sample configurations, where people manage GFS partitions with gfs2 init script - https://alteeve.ca/w/2-Node_Red_Hat_KVM_Cluster_Tutorial#Defining_The_Resources or even as simply as just enabling services such as clvm and gfs2 to start automatically at boot (http://pbraun.nethence.com/doc/filesystems/gfs2.html), like: chkconfig gfs2 on If I understand the latest approach correctly, such cluster only controls whether nodes are still alive and can fence errant ones, but such cluster has no control over the status of its resources. I have some experience with Pacemaker and I'm used to that all resources are controlled by a cluster and an action can be taken when not only there are connectivity issues, but any of the resources misbehave. So, which is the right way for me to go: leave GFS partition mounted (any reasons to do so?) set force_unmount="1". Won't this break anything? Why this is not the default? use script resource <script file="/etc/init.d/gfs2" name="gfs"/> to manage GFS partition. start it at boot and don't include in cluster.conf (any reasons to do so?) This may be a sort of question that cannot be answered unambiguously, so it would be also of much value for me if you shared your experience or expressed your thoughts on the issue. How does for example /etc/cluster/cluster.conf look like when configuring gfs with Conga or ccs (they are not available to me since for now I have to use Ubuntu for the cluster)? Thanks you very much!

  Read the article

• "Can't create table" when having to many partitions

  - by Chris

  I am currently having a problem I dont understand. Wherever I look it says mySQL (5.5) / InnoDB doesnt have a table limit. I wanted to test the InnoDB compression and was about to create an empty copy of an existing table and ran into the following problem. this one works: CREATE TABLE `hsc` ( LOTS OF STUFF ) ENGINE=InnoDB CHARSET=utf8 PARTITION BY RANGE (pid) SUBPARTITION BY HASH (cons) SUBPARTITIONS 2 (PARTITION hsc_p0 VALUES LESS THAN (10000) , PARTITION hsc_p1 VALUES LESS THAN (20000) , PARTITION hsc_p2 VALUES LESS THAN (30000) , PARTITION hsc_p3 VALUES LESS THAN (40000) , PARTITION hsc_p4 VALUES LESS THAN (50000) , PARTITION hsc_p40 VALUES LESS THAN (4000000) ); this one doesn't: CREATE TABLE `hsc` ( LOTS OF STUFF ) ENGINE=InnoDB CHARSET=utf8 PARTITION BY RANGE (pid) SUBPARTITION BY HASH (cons) SUBPARTITIONS 2 (PARTITION hsc_p0 VALUES LESS THAN (10000) , PARTITION hsc_p1 VALUES LESS THAN (20000) , PARTITION hsc_p2 VALUES LESS THAN (30000) , PARTITION hsc_p3 VALUES LESS THAN (40000) , PARTITION hsc_p4 VALUES LESS THAN (50000) , PARTITION hsc_p5 VALUES LESS THAN (75000) , PARTITION hsc_p6 VALUES LESS THAN (100000) , PARTITION hsc_p7 VALUES LESS THAN (125000) , PARTITION hsc_p8 VALUES LESS THAN (150000) , PARTITION hsc_p9 VALUES LESS THAN (175000) , PARTITION hsc_p40 VALUES LESS THAN (4000000) ); ERROR 1005 (HY000): Can't create table 'hsc' (errno: 1) Its reproducable by removing the number of partitions and adding them again. it does not have to do anything with the name of the table as i tried various names. there is also enough empty space on the HDD. /dev/simfs 230G 26G 192G 12% /var/lib/mysql.mnt There should be no limit on the partitions http://dev.mysql.com/doc/refman/5.5/en/partitioning-limitations.html Maximum number of partitions. The maximum possible number of partitions for a given table (that does not use the NDB storage engine) is 1024. This number includes subpartitions. i have increased both open_files show variables where variable_name LIKE '%open_files%'; +-------------------+-------+ | Variable_name | Value | +-------------------+-------+ | innodb_open_files | 512 | | open_files_limit | 1536 | +-------------------+-------+ No change. Any clues where should I start looking? UPDATE: the whole thing is running in an openvz environment. i saw in users_beancounters that the numflock was a problem, so i increased it. but the problem still persists. maybe this helps: ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 515011 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 10240 cpu time (seconds, -t) unlimited max user processes (-u) 515011 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited cat /proc/user_beancounters Version: 2.5 uid resource held maxheld barrier limit failcnt 200: kmemsize 9309653 13357056 14372700 14790164 0 lockedpages 0 1008 2048 2048 0 privvmpages 675424 686528 1048576 1572864 0 shmpages 33 673 21504 21504 0 dummy 0 0 9223372036854775807 9223372036854775807 0 numproc 49 90 240 240 0 physpages 243761 246945 0 9223372036854775807 0 vmguarpages 0 0 1048576 1048576 0 oomguarpages 81672 83305 1048576 1048576 0 numtcpsock 6 8 360 360 0 numflock 175 188 512 512 8 numpty 1 9 16 16 0 numsiginfo 0 48 256 256 0 tcpsndbuf 104640 263912 1720320 2703360 0 tcprcvbuf 98304 131072 1720320 2703360 0 othersockbuf 32368 89304 1126080 2097152 0 dgramrcvbuf 0 2312 262144 262144 0 numothersock 19 28 360 360 0 dcachesize 2285052 3624426 3409920 3624960 0 numfile 616 870 9312 9312 0 dummy 0 0 9223372036854775807 9223372036854775807 0 dummy 0 0 9223372036854775807 9223372036854775807 0 dummy 0 0 9223372036854775807 9223372036854775807 0 numiptent 24 24 128 128 0

  Read the article

• e2fsck / resize2fs problems

  - by BlakBat

  I've got 6 drives (each 1.5T, all same model and firmware revision) that are part of a RAID5 array. The RAID5 makes a LVM volume group and a logical group. The latter contains only one ext3 partition. I've recently ran: e2fsck -f /dev/vg03/lv01 && resize2fs -M /dev/vg03/lv01 which exited without an error. Now when I try to mount /dev/vg03/lv01 I get: EXT3-fs error (device dm-0): ext3_check_descriptors: Block bitmap for group 30533 not in group (block 1000532368)! EXT3-fs: group descriptors corrupted! How do I get out of this predicament? This is all the info I can currently give you: fdisk -l /dev/sd[cdefgh] shows (correctly) that they are "Linux raid autodetect" but fdisk now shows: fdisk -l /dev/md0 Disk /dev/md0: 7501.5 GB, 7501495664640 bytes ... Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table (instead of a LVM type partition) fdisk -l /dev/vg03/lv01 Disk /dev/vg03/lv01: 7501.5 GB, 7501491732480 bytes ... Disk identifier: 0x00000000 Disk /dev/vg03/lv01 doesn't contain a valid partition table (instead of a ext3 type partition) I've tried: e2fsck -fy /dev/vg03/lv01 e2fsck 1.41.12 (17-May-2010) e2fsck: Group descriptors look bad... trying backup blocks... Block bitmap for group 30533 is not in group. (block 1000532368) Relocate? yes Inode bitmap for group 30533 is not in group. (block 1000532369) Relocate? yes Pass 1: Checking inodes, blocks, and sizes Relocating group 30533's block bitmap to 1000524246... Error allocating 1 contiguous block(s) in block group 30533 for inode bitmap: Could not allocate block in ext2 filesystem e2fsck: aborted Extra information I can give you: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active (auto-read-only) raid5 sdg1[0] sdh1[5] sdf1[4] sde1[3] sdc1[2] sdd1[1] 7325679360 blocks level 5, 128k chunk, algorithm 2 [6/6] [UUUUUU] bitmap: 1/175 pages [4KB], 4096KB chunk unused devices: Lastly, all smartctl tests (short and extendend) showed no errors on any of the disks. Should I try to resize2fs to grow /dev/vg03/lv01 and redo a e2fsck ? Should I cfdisk /dev/md0 and /dev/vg03/lv01 back to their real types? Thanks in advance for all and any help. 2011-09-20 UPDATE I issued the following commands and was able to remount the partition, but by viewing the size (df) of before and after, it seems that 1Tb of data have gone missing. By checking the MD5SUMS (from an old backup) of some files with the "same" files from the remounted partition, some errors have been detected. Commands issued to remount the partition were: dumpe2fs /dev/vg03/lv01 Block count: 1000491435<br /> Block size: 4096<br /> tune2fs -O ^has_journal /dev/vg03/lv01 resize2fs -p /dev/vg03/lv01 dumpe2fs /dev/vg03/lv01 Block count: 1831418880<br /> Block size: 4096<br /> mount -o ro,noatime /dev/vg03/lv01 /mnt/raid OK... but files have been damaged / gone missing.

  Read the article

• ubuntu mount iso but some files are unreadable

  - by Chao

  I'm new to Linux and just installed ubuntu 12.04 amd64 this month. I had failed installing Texlive with texlive2012 iso image. I used the recommended command to mount: "mount -t iso9660 -o ro,loop,noauto /your/texlive2012.iso /mnt " But the installer failed to read some file. The iso is fine, I checked the md5. I extracted everything from iso with archive manager, and it installed successfully. So, why mount is not working? Thanks. UPDATE with furius iso mount tool, mount with Fuse, and it installed, with warning: Summary of warning messages during installation: Downloaded ./archive/calligra-type1.tar.xz, size equal, but md5sum differs; downloading again. While mount with Loop, it failed to install. Updated Error message from terminal, mounted with furius iso mount, loop. texlive2012-20120701_iso$ ./install-tl -gui Loading ./tlpkg/texlive.tlpdb Installing TeX Live 2012 from: . Platform: x86_64-linux = 'x86_64 with GNU/Linux' Distribution: inst (compressed) Directory for temporary files: /tmp Installing [0001/2481, time/total: ??:??/??:??]: 12many [3k] Installing [0002/2481, time/total: 00:00/00:00]: 2up [4k] Installing [0003/2481, time/total: 00:00/00:00]: Asana-Math [457k] Installing [0004/2481, time/total: 00:00/00:00]: ESIEEcv [2k] ... Installing [0265/2481, time/total: 00:10/01:09]: calctab [5k] Installing [0266/2481, time/total: 00:10/01:09]: calligra [42k] Installing [0267/2481, time/total: 00:10/01:09]: calligra-type1 [59k] Downloaded ./archive/calligra-type1.tar.xz, size equal, but md5sum differs; downloading again. ./tlpkg/installer/xz/xzdec.x86_64-linux: (stdin): File is corrupt tar: Unexpected EOF in archive tar: rmtlseek not stopped at a record boundary tar: Error is not recoverable: exiting now untar: untarring /home/lichao/ttt/temp/calligra-type1.tar failed (in /home/lichao/ttt/texmf-dist) untarring /home/lichao/ttt/temp/calligra-type1.tar failed, stopping install. Installation failed. Rerunning the installer will try to restart the installation. Or you can restart by running the installer with: install-tl --profile installation.profile [EXTRA-ARGS] ./install-tl: Could not write to install-tl.log, so flushing messages to stderr. Loading ./tlpkg/texlive.tlpdb Installing TeX Live 2012 from: . Platform: x86_64-linux = 'x86_64 with GNU/Linux' Distribution: inst (compressed) Directory for temporary files: /tmp Installer revision: 26794 Database revision: 26935 Installing [0001/2481, time/total: ??:??/??:??]: 12many [3k] Installing [0002/2481, time/total: 00:00/00:00]: 2up [4k] Installing [0003/2481, time/total: 00:00/00:00]: Asana-Math [457k] Installing [0004/2481, time/total: 00:00/00:00]: ESIEEcv [2k] Installing [0005/2481, time/total: 00:00/00:00]: FAQ-en [1k] ... Installing [0262/2481, time/total: 00:10/01:09]: c90 [2k] Installing [0263/2481, time/total: 00:10/01:09]: cachepic [5k] Installing [0264/2481, time/total: 00:10/01:09]: cachepic.x86_64-linux [1k] Installing [0265/2481, time/total: 00:10/01:09]: calctab [5k] Installing [0266/2481, time/total: 00:10/01:09]: calligra [42k] Installing [0267/2481, time/total: 00:10/01:09]: calligra-type1 [59k] Downloaded ./archive/calligra-type1.tar.xz, size equal, but md5sum differs; downloading again. untar: untarring /home/lichao/ttt/temp/calligra-type1.tar failed (in /home/lichao/ttt/texmf-dist) untarring /home/lichao/ttt/temp/calligra-type1.tar failed, stopping install. Installation failed. Rerunning the installer will try to restart the installation. Or you can restart by running the installer with: install-tl --profile installation.profile [EXTRA-ARGS] Segmentation fault (core dumped) I am sure that the iso is fine. I can open it with archive manager and all files are good. But after mounting it, even archive manager failed to open some files (which can be opened when the iso is opened in archive manager).

  Read the article

• Amazon EC2 Instance - m1.medium Ubuntu 12.04 - Started to crash three days ago

  - by Joy

  The environment: Amazon EC2 Instance - m1.medium Ubuntu 12.04 Apache 2.2.22 - Running a Drupal Site Using MySQL DB Server RAM info: ~$ free -gt total used free shared buffers cached Mem: 3 1 2 0 0 0 -/+ buffers/cache: 0 2 Swap: 0 0 0 Total: 3 1 2 Hard drive info: Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 4.7G 2.9G 62% / udev 1.9G 8.0K 1.9G 1% /dev tmpfs 751M 180K 750M 1% /run none 5.0M 0 5.0M 0% /run/lock none 1.9G 0 1.9G 0% /run/shm /dev/xvdb 394G 199M 374G 1% /mnt The problem About two days ago the site started failing becaue the MySQL server was shut down by Apache with the following message: kernel: [2963685.664359] [31716] 106 31716 226946 22748 0 0 0 mysqld kernel: [2963685.664730] Out of memory: Kill process 31716 (mysqld) score 23 or sacrifice child kernel: [2963685.664764] Killed process 31716 (mysqld) total-vm:907784kB, anon-rss:90992kB, file-rss:0kB kernel: [2963686.153608] init: mysql main process (31716) killed by KILL signal kernel: [2963686.169294] init: mysql main process ended, respawning That states that the VM was occupying 0.9GB, but my Ram has 2GB free, so 1GB was still left free. I understand that in Linux applications can allocate more memory than physically available. I don't know if this is the problme, it's the first time that it has started to happen. Obviously, the MySQL server tries to restart, but there's no memory for it apparently and it won't restart. Here is its error log: Plugin 'FEDERATED' is disabled. The InnoDB memory heap is disabled Mutexes and rw_locks use GCC atomic builtins Compressed tables use zlib 1.2.3.4 Initializing buffer pool, size = 128.0M InnoDB: mmap(137363456 bytes) failed; errno 12 Completed initialization of buffer pool Fatal error: cannot allocate memory for the buffer pool Plugin 'InnoDB' init function returned error. Plugin 'InnoDB' registration as a STORAGE ENGINE failed. Unknown/unsupported storage engine: InnoDB [ERROR] Aborting [Note] /usr/sbin/mysqld: Shutdown complete I simply restarted the Mysql service. About two hours later it happened again. I restarted it. Then it happened again 9 hours later. So then I thought of the MaxClients parameter of apache.conf, so I went to check it out. It was set at 150. I decided to drop it down to 60. As so: <IfModule mpm_prefork_module> ... MaxClients 60 </IfModule> <IfModule mpm_worker_module> ... MaxClients 60 </IfModule> <IfModule mpm_event_module> ... MaxClients 60 </IfModule> Once I did that, I had the apache2 service restart and it all went smoothly for 3/4 of a day. Since at night the MySQL service shut down once again, but this time it wasn't killed by the Apache2 service. Instead it called the OOM-Killer with the following message: kernel: [3104680.005312] mysqld invoked oom-killer: gfp_mask=0x201da, order=0, oom_adj=0, oom_score_adj=0 kernel: [3104680.005351] [<ffffffff81119795>] oom_kill_process+0x85/0xb0 kernel: [3104680.548860] init: mysql main process (30821) killed by KILL signal Now I'm out of ideas. Some articles state that the ideal thing to do is change the kernel behaviour with the following (include it to the file /etc/sysctl.conf ) vm.overcommit_memory = 2 vm.overcommit_ratio = 80 So no overcommits will take place. I'm wondering if this is the way to go? Keep in mind I'm no server administrator, I have basic knowldege. Thanks a bunch in advance.

  Read the article

• how to adjust the size of the root partition on live arch linux system (/dev/mapper/arch_root-image)

  - by leon

  Summary: I created a bootable usb drive with a live Bridge linux (ARCH based) on it. Everything works fine. The live system mounts a device called /dev/mapper/arch_root-image as its ext4 root partition (/ mount point). The problem is that I dont know how to control the size of this partition. This is not a Bridge specific issue (also happens with Archbang) Detail: My usb drive has a dos partition table with 2 ext2 partitions $ fdisk -l /dev/sdb Disk /dev/sdb: 29,8 GiB, 32006733824 bytes, 62513152 sectors Unités : secteur de 1 × 512 = 512 octets Taille de secteur (logique / physique) : 512 octets / 512 octets taille d'E/S (minimale / optimale) : 512 octets / 512 octets Type d'étiquette de disque : dos Identifiant de disque : 0x0007b7e2 Périphérique Amorçage Début Fin Blocs Id Système /dev/sdb1 * 2048 2002943 1000448 83 Linux /dev/sdb2 2002944 32258047 15127552 83 Linux sdb1 is approx 1GB and sdb2 is 14GB. The live system is on sdb1. sdb2 is empty. Now when I boot the live system, its filesystem looks like this: $ mount proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) sys on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) dev on /dev type devtmpfs (rw,nosuid,relatime,size=505272k,nr_inodes=126318,mode=755) run on /run type tmpfs (rw,nosuid,nodev,relatime,mode=755) /dev/sda1 on /run/archiso/bootmnt type ext2 (ro,relatime) cowspace on /run/archiso/cowspace type tmpfs (rw,relatime,size=772468k,mode=755) /dev/loop0 on /run/archiso/sfs/root-image type squashfs (ro,relatime) /dev/mapper/arch_root-image on / type ext4 (rw,relatime) securityfs on /sys/kernel/security type securityfs (rw,nosuid,nodev,noexec,relatime) tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /sys/fs/cgroup type tmpfs (rw,nosuid,nodev,noexec,mode=755) cgroup on /sys/fs/cgroup/systemd type cgroup (rw,nosuid,nodev,noexec,relatime,xattr,release_agent=/usr/lib/systemd/systemd-cgroups-agent,name=systemd) pstore on /sys/fs/pstore type pstore (rw,nosuid,nodev,noexec,relatime) cgroup on /sys/fs/cgroup/cpuset type cgroup (rw,nosuid,nodev,noexec,relatime,cpuset) cgroup on /sys/fs/cgroup/cpu,cpuacct type cgroup (rw,nosuid,nodev,noexec,relatime,cpuacct,cpu) cgroup on /sys/fs/cgroup/memory type cgroup (rw,nosuid,nodev,noexec,relatime,memory) cgroup on /sys/fs/cgroup/devices type cgroup (rw,nosuid,nodev,noexec,relatime,devices) cgroup on /sys/fs/cgroup/freezer type cgroup (rw,nosuid,nodev,noexec,relatime,freezer) cgroup on /sys/fs/cgroup/net_cls type cgroup (rw,nosuid,nodev,noexec,relatime,net_cls) cgroup on /sys/fs/cgroup/blkio type cgroup (rw,nosuid,nodev,noexec,relatime,blkio) mqueue on /dev/mqueue type mqueue (rw,relatime) debugfs on /sys/kernel/debug type debugfs (rw,relatime) hugetlbfs on /dev/hugepages type hugetlbfs (rw,relatime) configfs on /sys/kernel/config type configfs (rw,relatime) systemd-1 on /proc/sys/fs/binfmt_misc type autofs (rw,relatime,fd=36,pgrp=1,timeout=300,minproto=5,maxproto=5,direct) tmpfs on /tmp type tmpfs (rw) tmpfs on /etc/pacman.d/gnupg type tmpfs (rw,relatime,mode=755) As we can see, the root partition is from the device /dev/mapper/arch_root-image and my problem is that the live system recognizes it as a 3.9GB drive $ df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/arch_root-image 3.9G 1.9G 2.1G 48% / dev 494M 0 494M 0% /dev run 503M 23M 481M 5% /run /dev/sda1 962M 590M 324M 65% /run/archiso/bootmnt cowspace 755M 32M 723M 5% /run/archiso/cowspace /dev/loop0 520M 520M 0 100% /run/archiso/sfs/root-image tmpfs 503M 132K 503M 1% /dev/shm tmpfs 503M 0 503M 0% /sys/fs/cgroup tmpfs 503M 360K 503M 1% /tmp tmpfs 503M 896K 503M 1% /etc/pacman.d/gnupg My question is how is this size controled? I suspect this is related to the content of the aitab file which is part of the Bridge iso image: $ cat aitab # <img> <mnt> <arch> <sfs_comp> <fs_type> <fs_size> root-image / i686 xz ext4 50% I have read https://wiki.archlinux.org/index.php/archiso#aitab but found no clue

  Read the article

• Ops Center Solaris 11 IPS Repository Management: Using ISO Images

  - by S Stelting

  Please join us for a live WebEx presentation of this topic on Tuesday, November 20th at 9am MDT. Details for the call are provided below: https://oracleconferencing.webex.com/oracleconferencing/j.php?ED=209834017&UID=1512096072&PW=NYTVlZTYxMzdm&RT=MiMxMQ%3D%3D Meeting password: oracle123 Call-in toll-free number: 1-866-682-4770 International numbers: http://www.intercall.com/oracle/access_numbers.htm Conference Code: 762 9343 # Security Code: 7777 # With Enterprise Manager Ops Center 12c, you can provision, patch, monitor and manage Oracle Solaris 11 instances. To do this, Ops Center creates and maintains a Solaris 11 Image Packaging System (IPS) repository on the Enterprise Controller. During the Enterprise Controller configuration, you can load repository content directly from Oracle's Support Web site and subsequently synchronize the repository as new content becomes available. Of course, you can also use Solaris 11 ISO images to create and update your Ops Center repository. There are a few excellent reasons for doing this: You're running Ops Center in disconnected mode, and don't have Internet access on your Enterprise Controller You'd rather avoid the bandwidth associated with live synchronization of a Solaris 11 package repository This demo will show you how to use Solaris 11 ISO images to set up and update your Ops Center repository. Prerequisites This tip assumes that you've already installed the Enterprise Controller on a Solaris 11 OS instance and that you're ready for post-install configuration. In addition, there are specific Ops Center and OS version requirements depending on which version of Solaris 11 you plan to install.You can get full details about the requirements in the Release Notes for Ops Center 12c update 2. Additional information is available in the Ops Center update 2 Readme document. Part 1: Using a Solaris 11 ISO Image to Create an Ops Center Repository Step 1 – Download the Solaris 11 Repository Image The Oracle Web site provides a number of download links for official Solaris 11 images. Among those links is a two-part downloadable repository image, which provides repository content for Solaris 11 SPARC and X86 architectures. In this case, I used the Solaris 11 11/11 image. First, navigate to the Oracle Web site and accept the OTN License agreement: http://www.oracle.com/technetwork/server-storage/solaris11/downloads/index.html Next, download both parts of the Solaris 11 repository image. I recommend using the Solaris 11 11/11 image, and have provided the URLs here: http://download.oracle.com/otn/solaris/11/sol-11-1111-repo-full.iso-ahttp://download.oracle.com/otn/solaris/11/sol-11-1111-repo-full.iso-b Finally, use the cat command to generate an ISO image you can use to create your repository: # cat sol-11-1111-repo-full.iso-a sol-11-1111-repo-full.iso-b > sol-11-1111-repo-full.iso The process is very similar if you plan to set up a Solaris 11.1 release in Ops Center. In that case, navigate to the Solaris 11 download page, accept the license agreement and download both parts of the Solaris 11.1 repository image. Use the cat command to create a single ISO image for Solaris 11.1 Step 2 – Mount the Solaris 11 ISO Image in your Local Filesystem Once you have created the Solaris 11 ISO file, use the mount command to attach it to your local filesystem. After the image has been mounted, you can browse the repository from the ./repo subdirectory, and use the pkgrepo command to verify that Solaris 11 recognizes the content: Step 3 – Use the Image to Create your Ops Center Repository When you have confirmed the repository is available, you can use the image to create the Enterprise Controller repository. The operation will be slightly different depending on whether you configure Ops Center for Connected or Disconnected Mode operation.For connected mode operation, specify the mounted ./repo directory in step 4.1 of the configuration wizard, replacing the default Web-based URL. Since you're synchronizing from an OS repository image, you don't need to specify a key or certificate for the operation. For disconnected mode configuration, specify the Solaris 11 directory along with the path to the disconnected mode bundle downloaded by running the Ops Center harvester script: Ops Center will run a job to import package content from the mounted ISO image. A synchronization job can take several hours to run – in my case, the job ran for 3 hours, 22 minutes on a SunFire X4200 M2 server. During the job, Ops Center performs three important tasks: Synchronizes all content from the image and refreshes the repository Updates the IPS publisher information Creates OS Provisioning profiles and policies based on the content When the job is complete, you can unmount the ISO image from your Enterprise Controller. At that time, you can view the repository contents in your Ops Center Solaris 11 library. For the Solaris 11 11/11 release, you should see 8,668 packages and patches in the contents. You should also see default deployment plans for Solaris 11 provisioning. As part of the repository import, Ops Center generates plans and profiles for desktop, small and large servers for the SPARC and X86 architecture. Part 2: Using a Solaris 11 SRU to update an Ops Center Repository It's possible to use the same approach to upgrade your Ops Center repository to a Solaris 11 Support Repository Update, or SRU. Each SRU provides packages and updates to Solaris 11 - for example, SRU 8.5 provided the packaged for Oracle VM Server for SPARC 2.2 SRUs are available for download as ISO images from My Oracle Support, under document ID 1372094.1. The document provides download links for all SRUs which have been released by Oracle for Solaris 11. SRUs are cumulative, so later versions include the packages from earlier SRUs. After downloading an ISO image for an SRU, you can mount it to your local filesystem using a mount command similar to the one shown for Solaris 11 11/11. When the ISO image is mounted to the file system, you can perform the Add Content action from the Solaris 11 Library to synchronize packages and patches from the mounted image. I used the same mount point, so the repository URL was file://mnt/repo once again: After the synchronization of an SRU is complete, you can verify its content in the Solaris 11 library using the search function. The version pattern is 0.175.0.#, where the # is the same value as the SRU. In this example, I upgraded to SRU 1. The update job ran in just under 8 minutes, and a quick search shows that 22 software components were added to the repository: It's also possible to search for "Support Repository Update" to confirm the SRU was successfully added to the repository. Details on any of the update content are available by clicking the "View Details" button under the Packages/Patches entry.

  Read the article

• CodePlex Daily Summary for Thursday, March 11, 2010

  CodePlex Daily Summary for Thursday, March 11, 2010New ProjectsASP.NET Wiki Control: This ASP.NET user control allows you to embed a very useful wiki directly into your already existing ASP.NET website taking advantage of the popula...BabyLog: Log baby daily activity.buddyHome: buddyHome is a project that can make your home smarter. as good as your buddy. Cloud Community: Cloud Community makes it easier for organizations to have a simple to use community platform. Our mission is to create an easy to use community pl...Community Connectors for Microsoft CRM 4.0: Community Connectors for Microsoft CRM 4.0 allows Microsoft CRM 4.0 customers and partners to monitor and analyze customers’ interaction from their...Console Highlighter: Hightlights Microsoft Windows Command prompt (cmd.exe) by outputting ANSI VT100 Control sequences to color the output. These sequences are not hand...Cornell Store: This is IN NO WAY officially affiliated or related to the Cornell University store. Instead, this is a project that I am doing for a class. Ther...DevUtilities: This project is for creating some utility tools, and they will be useful during the development.DotNetNuke® Skin Maple: A DotNetNuke Design Challenge skin package submitted to the "Personal" category by DyNNamite.co.uk. The package includes 4 color variations and sev...HRNet: HRNetIIS Web Site Monitoring: A software for monitor a particular web site on IIS, even if its IP is sharing between different web site.Iowa Code Camp: The source code for the Iowa Code Camp website.Leonidas: Leonidas is a virtual tutorLunch 'n Learn: The Lunch 'n Learn web application is an open source ASP.NET MVC application that allows you to setup lunch 'n learn presentations for your team, c...MNT Cryptography: A very simple cryptography classMooiNooi MVC2LINQ2SQL Web Databinder: mvc2linq2sql is a databinder for ASP.NET MVC that make able developer to clean bind object from HTML FORMS to Linq entities. Even 1 to N relations ...MoqBot: MoqBot is an auto mocking library for Moq and Ninject.mtExperience1: hoiMvcPager: MvcPager is a free paging component for ASP.NET MVC web application, it exposes a series of extension methods for using in ASP.NET MVC applications...OCal: OCal is based on object calisthenics to identify code smellsPex Custom Arithmetic Solver: Pex Custom Arithmetic Solver contains a collection of meta-heuristic search algorithms. The goal is to improve Pex's code coverage for code involvi...SetControls: Расширеные контролы для ASP.NET приложений. Полная информация ближе к релизу...shadowrage1597: CTC 195 Game Design classSharePoint Team-Mailer: A SharePoint 2007 solution that defines a generic CustomList for sending e-mails to SharePoint Groups.Sql Share: SQL Share is a collaboration tool used within the science to allow database engineers to work tightly with domain scientists.TechCalendar: Tech Events Calendar ASP.NET project.ZLYScript: A very simple script language compiler.New ReleasesALGLIB: ALGLIB 2.4.0: New ALGLIB release contains: improved versions of several linear algebra algorithms: QR decomposition, matrix inversion, condition number estimatio...AmiBroker Plug-Ins with C#: AmiBroker Plug-Ins v0.0.2: Source codes and a binaryAppFabric Caching UI Admin Tool: AppFabric Caching Beta 2 UI Admin Tool: System Requirements:.NET 4.0 RC AppFabric Caching Beta2 Test On:Win 7 (64x)Autodocs - WCF REST Automatic API Documentation Generator: Autodocs.ServiceModel.Web: This archive contains the reference DLL, instructions and license.Compact Plugs & Compact Injection: Compact Injection and Compact Plugs 1.1 Beta: First release of Compact Plugs (CP). The solution includes a simple example project of CP, called "TestCompactPlugs1". Also some fixes where made ...Console Highlighter: Console Highlighter 0.9 (preview release): Preliminary release.Encrypted Notes: Encrypted Notes 1.3: This is the latest version of Encrypted Notes (1.3). It has an installer - it will create a directory 'CPascoe' in My Documents. The last one was ...Family Tree Analyzer: Version 1.0.2: Family Tree Analyzer Version 1.0.2 This early beta version implements loading a gedcom file and displaying some basic reports. These reports inclu...FRC1103 - FRC Dashboard viewer: 2010 Documentation v0.1: This is my current version of the control system documentation for 2010. It isn't complete, but it has the information required for a custom dashbo...jQuery.cssLess: jQuery.cssLess 0.5 (Even less release): NEW - support for nested special CSS classes (like :hover) MAIN RELEASE This release, code "Even less", is the one that will interpret cssLess wit...MooiNooi MVC2LINQ2SQL Web Databinder: MooiNooi MVC2LINQ2SQL DataBinder: I didn't try this... I just took it off from my project. Please, tell me any problem implementing in your own development and I'll be pleased to h...MvcPager: MvcPager 1.2 for ASP.NET MVC 1.0: MvcPager 1.2 for ASP.NET MVC 1.0Mytrip.Mvc: Mytrip 1.0 preview 1: Article Manager Blog Manager L2S Membership(.NET Framework 3.5) EF Membership(.NET Framework 4) User Manager File Manager Localization Captcha ...NodeXL: Network Overview, Discovery and Exploration for Excel: NodeXL Excel 2007 Template, version 1.0.1.117: The NodeXL Excel 2007 template displays a network graph using edge and vertex lists stored in an Excel 2007 workbook. What's NewThis version adds ...Pex Custom Arithmetic Solver: PexCustomArithmeticSolver: This is the alpha release containing the Alternating Variable Method and Evolution Strategies to try and solve constraints over floating point vari...Scrum Sprint Monitor: v1.0.0.44877: What is new in this release? Major performance increase in animations (up to 50 fps from 2 fps) by replacing DropShadow effect with png bitmaps; ...sELedit: sELedit v1.0b: + Added support for empty strings / wstrings + Fixed: critical bug in configuration files (list 53)sPWadmin: pwAdmin v0.9_nightly: + Fixed: XML editor can now open and save character templates + Added: PWI item name database + Added: Plugin SupportTechCalendar: Events Calendar v.1.0: Initial release.The Silverlight Hyper Video Player [http://slhvp.com]: Beta 2: Beta 2.0 Some fixes from Beta 1, and a couple small enhancements. Intensive testing continues, and I will continue to update the code at least ever...ThreadSafe.Caching: 2010.03.10.1: Updates to the scavanging behaviour since last release. Scavenging will now occur every 30 seconds by default and all objects in the cache will be ...VCC: Latest build, v2.1.30310.0: Automatic drop of latest buildVisual Studio DSite: Email Sender (C++): The same Email Sender program that I but made in visual c plus plus 2008 instead of visual basic 2008.Web Forms MVP: Web Forms MVP CTP7: The release can be considered stable, and is in use behind several high traffic, public websites. It has been marked as a CTP release as it is not ...White Tiger: 0.0.3.1: Now you can load or create files with whatever root element you want *check f or sets file permisionsMost Popular ProjectsMetaSharpWBFS ManagerRawrAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)ASP.NETMicrosoft SQL Server Community & SamplesASP.NET Ajax LibraryMost Active ProjectsUmbraco CMSRawrSDS: Scientific DataSet library and toolsN2 CMSFasterflect - A Fast and Simple Reflection APIjQuery Library for SharePoint Web ServicesBlogEngine.NETFarseer Physics Enginepatterns & practices – Enterprise LibraryCaliburn: An Application Framework for WPF and Silverlight

  Read the article

• No root file system is defined error after installation

  - by LearnCode

  I installed ubuntu through Wubi and once i rebooted I get no root file system defined error. here's the output of the boot_info_script.Could anyone point me out where the error is. Boot Info Script 0.60 from 17 May 2011 ============================= Boot Info Summary: =============================== => Windows is installed in the MBR of /dev/sda. => Windows is installed in the MBR of /dev/sdb. sda1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe /ntldr /ntdetect.com /wubildr /ubuntu/winboot/wubildr /wubildr.mbr /ubuntu/winboot/wubildr.mbr /ubuntu/disks/root.disk /ubuntu/disks/swap.disk sda1/Wubi: _____________________________________________________________________ File system: Boot sector type: Unknown Boot sector info: Mounting failed: mount: unknown filesystem type '' sda2: __________________________________________________________________________ File system: vfat Boot sector type: Unknown Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /boot.ini /ntldr /NTDETECT.COM sdb1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 160.0 GB, 160041885696 bytes 240 heads, 63 sectors/track, 20673 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 * 63 301,250,879 301,250,817 7 NTFS / exFAT / HPFS /dev/sda2 301,250,943 312,575,759 11,324,817 c W95 FAT32 (LBA) GUID Partition Table detected, but does not seem to be used. Partition Start Sector End Sector # of Sectors System /dev/sda1 323,465,741,313,502,988275,962,973,585-323,465,465,350,529,402 - /dev/sda2 242,728,591,638,290,720578,721,383,108,845,578335,992,791,470,554,859 - /dev/sda3 1,827,498,311,425,204,2562,091,935,274,843,009,907264,436,963,417,805,652 - /dev/sda4 579,711,218,081,401,3572,006,665,459,744,645,1521,426,954,241,663,243,796 - /dev/sda11 270,286,346,402,038,1183,786,543,326,404,525,9543,516,256,980,002,487,837 - /dev/sda12 4,179,681,002,230,769,6684,179,389,374,010,033,387-291,628,220,736,280 - /dev/sda13 232,556,480,979,456,1311,160,152,593,793,119,235927,596,112,813,663,105 - /dev/sda14 98,342,784,050,266,9183,691,264,578,843,725,1953,592,921,794,793,458,278 - /dev/sda15 2,307,845,219,957,882,4961,850,841,032,955,276,350-457,004,187,002,606,145 - /dev/sda16 512,592,046,878,946,497368,458,231,024,779,444-144,133,815,854,167,052 - /dev/sda17 2,504,135,232,870,384,3923,665,087,872,719,320,8291,160,952,639,848,936,438 - /dev/sda18 3,783,181,605,270,691,304122,034,509,624,708,942-3,661,147,095,645,982,361 - /dev/sda19 3,519,661,520,275,829,5122,376,243,094,723,723,587-1,143,418,425,552,105,924 - /dev/sda20 3,867,920,076,859,0744,494,691,111,933,625,1044,490,823,191,856,766,031 - /dev/sda21 1,500,144,061,909,253,7612,511,182,033,846,676,3401,011,037,971,937,422,580 - /dev/sda22 13,035,625,499,900,0062,360,168,613,941,394,9472,347,132,988,441,494,942 - /dev/sda23 4,228,978,682,068,599,48813,159,423,631,648,263-4,215,819,258,436,951,224 - /dev/sda24 3,695,955,742,872,046,9084,561,928,726,501,845,776865,972,983,629,798,869 - /dev/sda25 1,297,460,286,683,948,0461,444,350,486,339,417,957146,890,199,655,469,912 - /dev/sda26 1,228,858,248,533,131,831 0-1,228,858,248,533,131,830 - /dev/sda121 3,189,184,846,146,487,1461,849,820,258,006,914,852-1,339,364,588,139,572,293 - /dev/sda122 1,226,215,547,991,800,578389,781,518,734,546,300-836,434,029,257,254,277 - /dev/sda123 3,851,660,168,574,583,4654,046,215,657,583,031,556194,555,489,008,448,092 - /dev/sda124 1,197,460,980,174,153,341699,103,965,005,093,246-498,357,015,169,060,094 - Drive: sdb _____________________________________________________________________ Disk /dev/sdb: 750.2 GB, 750153367552 bytes 255 heads, 63 sectors/track, 91200 cylinders, total 1465143296 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdb1 2,048 1,465,143,295 1,465,141,248 7 NTFS / exFAT / HPFS "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/loop0 iso9660 Ubuntu 11.04 amd64 /dev/loop1 squashfs /dev/sda1 E814B55B14B52E06 ntfs /dev/sda2 01CD-023B vfat HP_RECOVERY /dev/sdb1 7836F22A36F1E8D0 ntfs Elements ================================ Mount points: ================================= Device Mount_Point Type Options /dev/loop0 /cdrom iso9660 (ro,noatime) /dev/loop1 /rofs squashfs (ro,noatime) /dev/sdb1 /mnt fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) ================================ sda2/boot.ini: ================================ -------------------------------------------------------------------------------- [boot loader] timeout=0 default=C:\CMDCONS\BOOTSECT.DAT [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Professional" /fastdetect C:\CMDCONS\BOOTSECT.DAT="Microsoft Windows Recovery Console" /cmdcons -------------------------------------------------------------------------------- ======================== Unknown MBRs/Boot Sectors/etc: ======================== Unknown GPT Partiton Type c104043000e9b9040dff24b580010100 Unknown GPT Partiton Type 46313020746f20737461727420746865 Unknown GPT Partiton Type 65727920706172746974696f6e207761 Unknown GPT Partiton Type 727920706172746974696f6e0d0a0000 Unknown GPT Partiton Type 000f84e5f7668b162404e82804744066 Unknown GPT Partiton Type ce01e8dc038bfe66391624047505e8d9 Unknown GPT Partiton Type 0345086603f0e881030bd2740333d240 Unknown GPT Partiton Type bece01e8db0287fec645041266895508 Unknown GPT Partiton Type 01f60634010175078b363b01e854f5e8 Unknown GPT Partiton Type 313825740ffec03865107408fec03824 Unknown GPT Partiton Type 02f60634014074088bfdbece01e85101 Unknown GPT Partiton Type 263401f9e894f30f858ef4e8e201e8ec Unknown GPT Partiton Type f7e960f35245434f5645525966606633 Unknown GPT Partiton Type 660faf1e00106603dac3668b0e001066 Unknown GPT Partiton Type 8bfd386d04740583c710e2f6c36660c6 Unknown GPT Partiton Type 04ebf132c0b91000f3aac3bf0c04ebf3 Unknown GPT Partiton Type 02662bc1660fb71e0e02662bc366031e Unknown GPT Partiton Type f4b40ebb0700b901003c08751381ff25 Unknown GPT Partiton Type 534f465448494e4b90653f62011b0100 Unknown GPT Partiton Type 0b050900027777772e68702e636f6d00 Unknown GPT Partiton Type d441a0f5030003000ecb744a08bb3746 Unknown GPT Partiton Type f8579a116b4a7aa931cde97a4b9b5c09 Unknown GPT Partiton Type 7229990415b77c0a1970e7e824237a3a Unknown GPT Partiton Type afb6e34d6b4bd8c7c0eada19a9786cc3 Unknown BootLoader on sda1/Wubi 00000000 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 |0000000000000000| * 00000200 Unknown BootLoader on sda2 00000000 e9 a7 00 52 45 43 4f 56 45 52 59 00 02 08 20 00 |...RECOVERY... .| 00000010 02 00 00 00 00 f8 00 00 3f 00 f0 00 7f b9 f4 11 |........?.......| 00000020 8c cd ac 00 1e 2b 00 00 00 00 00 00 02 00 00 00 |.....+..........| 00000030 01 00 06 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00000040 80 00 29 3b 02 cd 01 20 20 20 20 20 20 20 20 20 |..);... | 00000050 20 20 46 41 54 33 32 20 20 20 8b d0 c1 e2 02 80 | FAT32 ......| 00000060 e6 01 66 c1 e8 07 66 3b 46 f8 74 2a 66 89 46 f8 |..f...f;F.t*f.F.| 00000070 66 03 46 f4 66 0f b6 5e 28 80 e3 0f 74 0f 3a 5e |f.F.f..^(...t.:^| 00000080 10 0f 83 90 00 66 0f af 5e 24 66 03 c3 bb e0 07 |.....f..^$f.....| 00000090 b9 01 00 e8 cf 00 8b da 66 8b 87 00 7e 66 25 ff |........f...~f%.| 000000a0 ff ff 0f 66 3d f8 ff ff 0f c3 33 c9 8e d9 8e c1 |...f=.....3.....| 000000b0 8e d1 66 bc f4 7b 00 00 bd 00 7c 66 0f b6 46 10 |..f..{....|f..F.| 000000c0 66 f7 66 24 66 0f b7 56 0e 66 03 56 1c 66 89 56 |f.f$f..V.f.V.f.V| 000000d0 f4 66 03 c2 66 89 46 fc 66 c7 46 f8 ff ff ff ff |.f..f.F.f.F.....| 000000e0 66 8b 46 2c 66 50 e8 af 00 bb 70 00 b9 01 00 e8 |f.F,fP....p.....| 000000f0 73 00 bf 00 07 b1 0b be a9 7d f3 a6 74 2a 03 f9 |s........}..t*..| 00000100 83 c7 15 81 ff 00 09 72 ec 66 40 4a 75 db 66 58 |[email protected]| 00000110 e8 47 ff 72 cf be b4 7d ac 84 c0 74 09 b4 0e bb |.G.r...}...t....| 00000120 07 00 cd 10 eb f2 cd 19 66 58 ff 75 09 ff 75 0f |........fX.u..u.| 00000130 66 58 bb 00 20 66 83 f8 02 72 da 66 3d f8 ff ff |fX.. f...r.f=...| 00000140 0f 73 d2 66 50 e8 50 00 0f b6 4e 0d e8 16 00 c1 |.s.fP.P...N.....| 00000150 e1 05 03 d9 66 58 53 e8 00 ff 5b 72 d8 8a 56 40 |....fXS...[r..V@| 00000160 ea 00 00 00 20 66 60 66 6a 00 66 50 53 6a 00 66 |.... f`fj.fPSj.f| 00000170 68 10 00 01 00 8b f4 b8 00 42 8a 56 40 cd 13 be |h........B.V@...| 00000180 c7 7d 72 94 67 83 44 24 06 20 66 67 ff 44 24 08 |.}r.g.D$. fg.D$.| 00000190 e2 e3 83 c4 10 66 61 c3 66 48 66 48 66 0f b6 56 |.....fa.fHfHf..V| 000001a0 0d 66 f7 e2 66 03 46 fc c3 4e 54 4c 44 52 20 20 |.f..f.F..NTLDR | 000001b0 20 20 20 20 0d 0a 4e 6f 20 53 79 73 74 65 6d 20 | ..No System | 000001c0 44 69 73 6b 20 6f 72 0d 0a 44 69 73 6b 20 49 2f |Disk or..Disk I/| 000001d0 4f 20 65 72 72 6f 72 0d 0a 50 72 65 73 73 20 61 |O error..Press a| 000001e0 20 6b 65 79 20 74 6f 20 72 65 73 74 61 72 74 0d | key to restart.| 000001f0 0a 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.| 00000200 =============================== StdErr Messages: =============================== umount: /isodevice: device is busy. (In some cases useful info about processes that use the device is found by lsof(8) or fuser(1))

  Read the article

• Exalogic 2.0.1 Tea Break Snippets - Creating a ModifyJeOS VirtualBox

  - by The Old Toxophilist

  Following on from my previous blog entry "Modifying the Base Template" I decided to put together a quick blog to show how to create a small VirtualBox, guest, that can be used to execute the ModifyJeOS and hence edit you templates. One of the main advantages of this is that Templates can be created away from the Exalogic Environment. For the Guest OS I chose OEL 6u3 and decided to create it as a basic server because I did not require a graphical interface but it's a simple change to create it with a GUI. Required Software Virtual Box. Oracle Enterprise Linux. Creating the VM I'll assume that the reader is experienced with Virtual Box and installing OEL and hence will make this section brief. Create VirtualBox Guest Create a new VirtualBox Guest and select oracle Linux 64 bit. Follow through the create process and select Dynamic Disk Size and the default 12GB disk size. The actual image will be a lot smaller than this but the OEL install will fail with insufficient disk space if you attempt a smaller size. Once the guest has been created attach the previously downloaded OEL 6u3 iso to the cd drive and start the guest. Install OEL On starting the guest the system will boot off the associated OEL 6u3 iso and take you through the standard installation process. Select all the appropriate information but when you reach the installation type select Basic Server because we do not need that additional packages and only need to access through the command line interface. Complete the installation and reboot the Guest. At this point we now have a basic OEL server running. Installing Guest Add-ons Before we can easily access the Guest we will need to add the VirtualBox guest add-ons. These will provide better keyboard and mouse integration and allow access the shared folders on the host machine. Before we can do this we will need to do the following: Enable Networking. Install additional rpms.  To enable the networking (eth0), that appears to be disabled by default, we can execute: ifup eth0 This will start the eth0 connection but once the Guest is rebooted the network will be down again. To resolve this you will need to edit the /etc/sysconfig/network-scripts/ifcfg-eth0 file and change the ONBOOT parameter to "yes". Now we have enabled the network we will need to install a number of addition rpm. First we will need to configure the yum repository as follows: [ol6_latest] name=Oracle Linux $releasever Latest ($basearch) baseurl=http://public-yum.oracle.com/repo/OracleLinux/OL6/latest/$basearch/ gpgkey=http://public-yum.oracle.com/RPM-GPG-KEY-oracle-ol6 gpgcheck=1 enabled=1 [ol6_ga_base] name=Oracle Linux $releasever GA installation media copy ($basearch) baseurl=http://public-yum.oracle.com/repo/OracleLinux/OL6/0/base/$basearch/ gpgkey=http://public-yum.oracle.com/RPM-GPG-KEY-oracle-ol6 gpgcheck=1 enabled=0 [ol6_u1_base] name=Oracle Linux $releasever Update 1 installation media copy ($basearch) baseurl=http://public-yum.oracle.com/repo/OracleLinux/OL6/1/base/$basearch/ gpgkey=http://public-yum.oracle.com/RPM-GPG-KEY-oracle-ol6 gpgcheck=1 enabled=0 [ol6_u2_base] name=Oracle Linux $releasever Update 2 installation media copy ($basearch) baseurl=http://public-yum.oracle.com/repo/OracleLinux/OL6/2/base/$basearch/ gpgkey=http://public-yum.oracle.com/RPM-GPG-KEY-oracle-ol6 gpgcheck=1 enabled=0 [ol6_u3_base] name=Oracle Linux $releasever Update 3 installation media copy ($basearch) baseurl=http://public-yum.oracle.com/repo/OracleLinux/OL6/3/base/$basearch/ gpgkey=http://public-yum.oracle.com/RPM-GPG-KEY-oracle-ol6 gpgcheck=1 enabled=0 [ol6_UEK_latest] name=Latest Unbreakable Enterprise Kernel for Oracle Linux $releasever ($basearch) baseurl=http://public-yum.oracle.com/repo/OracleLinux/OL6/UEK/latest/$basearch/ gpgkey=http://public-yum.oracle.com/RPM-GPG-KEY-oracle-ol6 gpgcheck=1 enabled=1 [ol6_UEK_base] name=Unbreakable Enterprise Kernel for Oracle Linux $releasever ($basearch) baseurl=http://public-yum.oracle.com/repo/OracleLinux/OL6/UEK/base/$basearch/ gpgkey=http://public-yum.oracle.com/RPM-GPG-KEY-oracle-ol6 gpgcheck=1 enabled=0 Once the repository has been edited we will need to execute the following yum commands: yum update yum install gcc yum install kernel-uek-devel yum install kernel-devel yum install createrepo At this point we now have all the additional packages required to install the VirtualBox Guest Add-ons. So select Devices->InstallGuest Additions on you running guest: This will simply place the VirtualBoxGuestAdditions.iso in the virtual cd and we will need to execute the following before we can run them. mkdir /media/cdrom mount -t iso9660 -o ro /dev/cdrom /media/cdrom cd /media/cdrom/ ls ./VBoxLinuxAdditions.run This will initiate the install and kernel rebuild. What you will notice is that during the installation a Failed will be displayed but this is simply because we have no graphical components. At this point we the installation will also have added the vboxsf group to the system and to access any shared folders we will create our user will need to be a member of this group an so the next stage is to add the root user to this group as follows: usermod -G vboxsf root cat /etc/group cat /etc/passwd init 0 Now simply shutdown the guest and add the Shared folder within your guests settings. Install ModifyJeOS Once the shared folder has been added restart the guest and change directory into the shared folder (/media/sf_<folder name>). For the next step I am assuming the ModifyJeOS rpms are located in the shared folder. We can simply execute: rpm -ivh ovm-modify-jeos-1.1.0-17.el5.noarch.rpm # Test with modifyjeos Using ModifyJeOS I have a modified MountSystemImg.sh script that should be copied into the /root/bin directory (you may need to create this) and from here it can be executed from any location: MountSystemImg.sh #!/bin/sh # The script assumes it's being run from the directory containing the System.img # Export for later i.e. during unmount export LOOP=`losetup -f` export SYSTEMIMG=/mnt/elsystem export TEMPLATEDIR=`pwd` # Make Temp Mount Directory mkdir -p $SYSTEMIMG # Create Loop for the System Image losetup $LOOP System.img kpartx -a $LOOP mount /dev/mapper/`basename $LOOP`p2 $SYSTEMIMG #Change Dir into mounted Image cd $SYSTEMIMG echo "######################################################################" echo "### ###" echo "### Starting Bash shell for editing. When completed log out to ###" echo "### Unmount the System.img file. ###" echo "### ###" echo "######################################################################" echo bash cd ~ cd $TEMPLATEDIR umount $SYSTEMIMG kpartx -d $LOOP losetup -d $LOOP rm -rf $SYSTEMIMG This script will simple create a mount directory, mount the System.img and then start a new shell in the mounted directory. On exiting the shell it will unmount the System.img. It only requires that you execute the script in the directory containing the System.img. These can be created under the mounted shared directory. In the example below I have extracted the Base template within the shared folder and then renamed it OEL_40GB_ROOT before changing into that directory and executing the script.

  Read the article

• Juju Openstack bundle: Can't launch an instance

  - by user281985

  Deployed bundle:~makyo/openstack/2/openstack, on top of 7 physical boxes and 3 virtual ones. After changing vip_iface strings to point to right devices, e.g., br0 instead of eth0, and defining "/mnt/loopback|30G", in Cinder's block-device string, am able to navigate through openstack dashboard, error free. Following http://docs.openstack.org/grizzly/openstack-compute/install/apt/content/running-an-instance.html instructions, attempted to launch cirros 0.3.1 image; however, novalist shows the instance in error state. ubuntu@node7:~$ nova --debug boot --flavor 1 --image 28bed1bc-bc1c-4533-beee-8e0428ad40dd --key_name key2 --security_group default cirros REQ: curl -i http://keyStone.IP:5000/v2.0/tokens -X POST -H "Content-Type: application/json" -H "Accept: application/json" -H "User-Agent: python-novaclient" -d '{"auth": {"tenantName": "admin", "passwordCredentials": {"username": "admin", "password": "openstack"}}}' INFO (connectionpool:191) Starting new HTTP connection (1): keyStone.IP DEBUG (connectionpool:283) "POST /v2.0/tokens HTTP/1.1" 200 None RESP: [200] {'date': 'Tue, 10 Jun 2014 00:01:02 GMT', 'transfer-encoding': 'chunked', 'vary': 'X-Auth-Token', 'content-type': 'application/json'} RESP BODY: {"access": {"token": {"expires": "2014-06-11T00:01:02Z", "id": "3eefa1837d984426a633fe09259a1534", "tenant": {"description": "Created by Juju", "enabled": true, "id": "08cff06d13b74492b780d9ceed699239", "name": "admin"}}, "serviceCatalog": [{"endpoints": [{"adminURL": "http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239", "region": "RegionOne", "internalURL": "http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239", "publicURL": "http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239"}], "endpoints_links": [], "type": "compute", "name": "nova"}, {"endpoints": [{"adminURL": "http://nova.cloud.controller:9696", "region": "RegionOne", "internalURL": "http://nova.cloud.controller:9696", "publicURL": "http://nova.cloud.controller:9696"}], "endpoints_links": [], "type": "network", "name": "quantum"}, {"endpoints": [{"adminURL": "http://nova.cloud.controller:3333", "region": "RegionOne", "internalURL": "http://nova.cloud.controller:3333", "publicURL": "http://nova.cloud.controller:3333"}], "endpoints_links": [], "type": "s3", "name": "s3"}, {"endpoints": [{"adminURL": "http://i.p.s.36:9292", "region": "RegionOne", "internalURL": "http://i.p.s.36:9292", "publicURL": "http://i.p.s.36:9292"}], "endpoints_links": [], "type": "image", "name": "glance"}, {"endpoints": [{"adminURL": "http://i.p.s.39:8776/v1/08cff06d13b74492b780d9ceed699239", "region": "RegionOne", "internalURL": "http://i.p.s.39:8776/v1/08cff06d13b74492b780d9ceed699239", "publicURL": "http://i.p.s.39:8776/v1/08cff06d13b74492b780d9ceed699239"}], "endpoints_links": [], "type": "volume", "name": "cinder"}, {"endpoints": [{"adminURL": "http://nova.cloud.controller:8773/services/Cloud", "region": "RegionOne", "internalURL": "http://nova.cloud.controller:8773/services/Cloud", "publicURL": "http://nova.cloud.controller:8773/services/Cloud"}], "endpoints_links": [], "type": "ec2", "name": "ec2"}, {"endpoints": [{"adminURL": "http://keyStone.IP:35357/v2.0", "region": "RegionOne", "internalURL": "http://keyStone.IP:5000/v2.0", "publicURL": "http://i.p.s.44:5000/v2.0"}], "endpoints_links": [], "type": "identity", "name": "keystone"}], "user": {"username": "admin", "roles_links": [], "id": "b3730a52a32e40f0a9500440d1ef1c7d", "roles": [{"id": "e020001eb9a049f4a16540238ab158aa", "name": "Admin"}, {"id": "b84fbff4d5554d53bbbffdaad66b56cb", "name": "KeystoneServiceAdmin"}, {"id": "129c8b49d42b4f0796109aaef2069aa9", "name": "KeystoneAdmin"}], "name": "admin"}}} REQ: curl -i http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/images/28bed1bc-bc1c-4533-beee-8e0428ad40dd -X GET -H "X-Auth-Project-Id: admin" -H "User-Agent: python-novaclient" -H "Accept: application/json" -H "X-Auth-Token: 3eefa1837d984426a633fe09259a1534" INFO (connectionpool:191) Starting new HTTP connection (1): nova.cloud.controller DEBUG (connectionpool:283) "GET /v1.1/08cff06d13b74492b780d9ceed699239/images/28bed1bc-bc1c-4533-beee-8e0428ad40dd HTTP/1.1" 200 719 RESP: [200] {'date': 'Tue, 10 Jun 2014 00:01:03 GMT', 'x-compute-request-id': 'req-7f3459f8-d3d5-47f1-97a3-8407a4419a69', 'content-type': 'application/json', 'content-length': '719'} RESP BODY: {"image": {"status": "ACTIVE", "updated": "2014-06-09T22:17:54Z", "links": [{"href": "http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/images/28bed1bc-bc1c-4533-beee-8e0428ad40dd", "rel": "self"}, {"href": "http://nova.cloud.controller:8774/08cff06d13b74492b780d9ceed699239/images/28bed1bc-bc1c-4533-beee-8e0428ad40dd", "rel": "bookmark"}, {"href": "http://External.Public.Port:9292/08cff06d13b74492b780d9ceed699239/images/28bed1bc-bc1c-4533-beee-8e0428ad40dd", "type": "application/vnd.openstack.image", "rel": "alternate"}], "id": "28bed1bc-bc1c-4533-beee-8e0428ad40dd", "OS-EXT-IMG-SIZE:size": 13147648, "name": "Cirros 0.3.1", "created": "2014-06-09T22:17:54Z", "minDisk": 0, "progress": 100, "minRam": 0, "metadata": {}}} REQ: curl -i http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/flavors/1 -X GET -H "X-Auth-Project-Id: admin" -H "User-Agent: python-novaclient" -H "Accept: application/json" -H "X-Auth-Token: 3eefa1837d984426a633fe09259a1534" INFO (connectionpool:191) Starting new HTTP connection (1): nova.cloud.controller DEBUG (connectionpool:283) "GET /v1.1/08cff06d13b74492b780d9ceed699239/flavors/1 HTTP/1.1" 200 418 RESP: [200] {'date': 'Tue, 10 Jun 2014 00:01:04 GMT', 'x-compute-request-id': 'req-2c153110-6969-4f3a-b51c-8f1a6ce75bee', 'content-type': 'application/json', 'content-length': '418'} RESP BODY: {"flavor": {"name": "m1.tiny", "links": [{"href": "http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/flavors/1", "rel": "self"}, {"href": "http://nova.cloud.controller:8774/08cff06d13b74492b780d9ceed699239/flavors/1", "rel": "bookmark"}], "ram": 512, "OS-FLV-DISABLED:disabled": false, "vcpus": 1, "swap": "", "os-flavor-access:is_public": true, "rxtx_factor": 1.0, "OS-FLV-EXT-DATA:ephemeral": 0, "disk": 0, "id": "1"}} REQ: curl -i http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/servers -X POST -H "X-Auth-Project-Id: admin" -H "User-Agent: python-novaclient" -H "Content-Type: application/json" -H "Accept: application/json" -H "X-Auth-Token: 3eefa1837d984426a633fe09259a1534" -d '{"server": {"name": "cirros", "imageRef": "28bed1bc-bc1c-4533-beee-8e0428ad40dd", "key_name": "key2", "flavorRef": "1", "max_count": 1, "min_count": 1, "security_groups": [{"name": "default"}]}}' INFO (connectionpool:191) Starting new HTTP connection (1): nova.cloud.controller DEBUG (connectionpool:283) "POST /v1.1/08cff06d13b74492b780d9ceed699239/servers HTTP/1.1" 202 436 RESP: [202] {'date': 'Tue, 10 Jun 2014 00:01:05 GMT', 'x-compute-request-id': 'req-41e53086-6454-4efb-bb35-a30dc2c780be', 'content-type': 'application/json', 'location': 'http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/servers/2eb5e3ad-3044-41c1-bbb7-10f398f83e43', 'content-length': '436'} RESP BODY: {"server": {"security_groups": [{"name": "default"}], "OS-DCF:diskConfig": "MANUAL", "id": "2eb5e3ad-3044-41c1-bbb7-10f398f83e43", "links": [{"href": "http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/servers/2eb5e3ad-3044-41c1-bbb7-10f398f83e43", "rel": "self"}, {"href": "http://nova.cloud.controller:8774/08cff06d13b74492b780d9ceed699239/servers/2eb5e3ad-3044-41c1-bbb7-10f398f83e43", "rel": "bookmark"}], "adminPass": "oFRbvRqif2C8"}} REQ: curl -i http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/servers/2eb5e3ad-3044-41c1-bbb7-10f398f83e43 -X GET -H "X-Auth-Project-Id: admin" -H "User-Agent: python-novaclient" -H "Accept: application/json" -H "X-Auth-Token: 3eefa1837d984426a633fe09259a1534" INFO (connectionpool:191) Starting new HTTP connection (1): nova.cloud.controller DEBUG (connectionpool:283) "GET /v1.1/08cff06d13b74492b780d9ceed699239/servers/2eb5e3ad-3044-41c1-bbb7-10f398f83e43 HTTP/1.1" 200 1349 RESP: [200] {'date': 'Tue, 10 Jun 2014 00:01:05 GMT', 'x-compute-request-id': 'req-d91d0858-7030-469d-8e55-40e05e4d00fd', 'content-type': 'application/json', 'content-length': '1349'} RESP BODY: {"server": {"status": "BUILD", "updated": "2014-06-10T00:01:05Z", "hostId": "", "OS-EXT-SRV-ATTR:host": null, "addresses": {}, "links": [{"href": "http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/servers/2eb5e3ad-3044-41c1-bbb7-10f398f83e43", "rel": "self"}, {"href": "http://nova.cloud.controller:8774/08cff06d13b74492b780d9ceed699239/servers/2eb5e3ad-3044-41c1-bbb7-10f398f83e43", "rel": "bookmark"}], "key_name": "key2", "image": {"id": "28bed1bc-bc1c-4533-beee-8e0428ad40dd", "links": [{"href": "http://nova.cloud.controller:8774/08cff06d13b74492b780d9ceed699239/images/28bed1bc-bc1c-4533-beee-8e0428ad40dd", "rel": "bookmark"}]}, "OS-EXT-STS:task_state": "scheduling", "OS-EXT-STS:vm_state": "building", "OS-EXT-SRV-ATTR:instance_name": "instance-00000004", "OS-EXT-SRV-ATTR:hypervisor_hostname": null, "flavor": {"id": "1", "links": [{"href": "http://nova.cloud.controller:8774/08cff06d13b74492b780d9ceed699239/flavors/1", "rel": "bookmark"}]}, "id": "2eb5e3ad-3044-41c1-bbb7-10f398f83e43", "security_groups": [{"name": "default"}], "OS-EXT-AZ:availability_zone": "nova", "user_id": "b3730a52a32e40f0a9500440d1ef1c7d", "name": "cirros", "created": "2014-06-10T00:01:04Z", "tenant_id": "08cff06d13b74492b780d9ceed699239", "OS-DCF:diskConfig": "MANUAL", "accessIPv4": "", "accessIPv6": "", "progress": 0, "OS-EXT-STS:power_state": 0, "config_drive": "", "metadata": {}}} REQ: curl -i http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/flavors/1 -X GET -H "X-Auth-Project-Id: admin" -H "User-Agent: python-novaclient" -H "Accept: application/json" -H "X-Auth-Token: 3eefa1837d984426a633fe09259a1534" INFO (connectionpool:191) Starting new HTTP connection (1): nova.cloud.controller DEBUG (connectionpool:283) "GET /v1.1/08cff06d13b74492b780d9ceed699239/flavors/1 HTTP/1.1" 200 418 RESP: [200] {'date': 'Tue, 10 Jun 2014 00:01:05 GMT', 'x-compute-request-id': 'req-896c0120-1102-4408-9e09-cd628f2dd699', 'content-type': 'application/json', 'content-length': '418'} RESP BODY: {"flavor": {"name": "m1.tiny", "links": [{"href": "http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/flavors/1", "rel": "self"}, {"href": "http://nova.cloud.controller:8774/08cff06d13b74492b780d9ceed699239/flavors/1", "rel": "bookmark"}], "ram": 512, "OS-FLV-DISABLED:disabled": false, "vcpus": 1, "swap": "", "os-flavor-access:is_public": true, "rxtx_factor": 1.0, "OS-FLV-EXT-DATA:ephemeral": 0, "disk": 0, "id": "1"}} REQ: curl -i http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/images/28bed1bc-bc1c-4533-beee-8e0428ad40dd -X GET -H "X-Auth-Project-Id: admin" -H "User-Agent: python-novaclient" -H "Accept: application/json" -H "X-Auth-Token: 3eefa1837d984426a633fe09259a1534" INFO (connectionpool:191) Starting new HTTP connection (1): nova.cloud.controller DEBUG (connectionpool:283) "GET /v1.1/08cff06d13b74492b780d9ceed699239/images/28bed1bc-bc1c-4533-beee-8e0428ad40dd HTTP/1.1" 200 719 RESP: [200] {'date': 'Tue, 10 Jun 2014 00:01:05 GMT', 'x-compute-request-id': 'req-454e9651-c247-4d31-8049-6b254de050ae', 'content-type': 'application/json', 'content-length': '719'} RESP BODY: {"image": {"status": "ACTIVE", "updated": "2014-06-09T22:17:54Z", "links": [{"href": "http://nova.cloud.controller:8774/v1.1/08cff06d13b74492b780d9ceed699239/images/28bed1bc-bc1c-4533-beee-8e0428ad40dd", "rel": "self"}, {"href": "http://nova.cloud.controller:8774/08cff06d13b74492b780d9ceed699239/images/28bed1bc-bc1c-4533-beee-8e0428ad40dd", "rel": "bookmark"}, {"href": "http://External.Public.Port:9292/08cff06d13b74492b780d9ceed699239/images/28bed1bc-bc1c-4533-beee-8e0428ad40dd", "type": "application/vnd.openstack.image", "rel": "alternate"}], "id": "28bed1bc-bc1c-4533-beee-8e0428ad40dd", "OS-EXT-IMG-SIZE:size": 13147648, "name": "Cirros 0.3.1", "created": "2014-06-09T22:17:54Z", "minDisk": 0, "progress": 100, "minRam": 0, "metadata": {}}} +-------------------------------------+--------------------------------------+ | Property | Value | +-------------------------------------+--------------------------------------+ | OS-EXT-STS:task_state | scheduling | | image | Cirros 0.3.1 | | OS-EXT-STS:vm_state | building | | OS-EXT-SRV-ATTR:instance_name | instance-00000004 | | flavor | m1.tiny | | id | 2eb5e3ad-3044-41c1-bbb7-10f398f83e43 | | security_groups | [{u'name': u'default'}] | | user_id | b3730a52a32e40f0a9500440d1ef1c7d | | OS-DCF:diskConfig | MANUAL | | accessIPv4 | | | accessIPv6 | | | progress | 0 | | OS-EXT-STS:power_state | 0 | | OS-EXT-AZ:availability_zone | nova | | config_drive | | | status | BUILD | | updated | 2014-06-10T00:01:05Z | | hostId | | | OS-EXT-SRV-ATTR:host | None | | key_name | key2 | | OS-EXT-SRV-ATTR:hypervisor_hostname | None | | name | cirros | | adminPass | oFRbvRqif2C8 | | tenant_id | 08cff06d13b74492b780d9ceed699239 | | created | 2014-06-10T00:01:04Z | | metadata | {} | +-------------------------------------+--------------------------------------+ ubuntu@node7:~$ ubuntu@node7:~$ nova list +--------------------------------------+--------+--------+----------+ | ID | Name | Status | Networks | +--------------------------------------+--------+--------+----------+ | 2eb5e3ad-3044-41c1-bbb7-10f398f83e43 | cirros | ERROR | | +--------------------------------------+--------+--------+----------+ ubuntu@node7:~$ var/log/nova/nova-compute.log shows the following error: ... 2014-06-10 00:01:06.048 AUDIT nova.compute.claims [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Attempting claim: memory 512 MB, disk 0 GB, VCPUs 1 2014-06-10 00:01:06.049 AUDIT nova.compute.claims [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Total Memory: 3885 MB, used: 512 MB 2014-06-10 00:01:06.049 AUDIT nova.compute.claims [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Memory limit: 5827 MB, free: 5315 MB 2014-06-10 00:01:06.049 AUDIT nova.compute.claims [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Total Disk: 146 GB, used: 0 GB 2014-06-10 00:01:06.050 AUDIT nova.compute.claims [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Disk limit not specified, defaulting to unlimited 2014-06-10 00:01:06.050 AUDIT nova.compute.claims [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Total CPU: 2 VCPUs, used: 0 VCPUs 2014-06-10 00:01:06.050 AUDIT nova.compute.claims [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] CPU limit not specified, defaulting to unlimited 2014-06-10 00:01:06.051 AUDIT nova.compute.claims [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Claim successful 2014-06-10 00:01:06.963 WARNING nova.network.quantumv2.api [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] No network configured! 2014-06-10 00:01:08.347 ERROR nova.compute.manager [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Instance failed to spawn 2014-06-10 00:01:08.347 32223 TRACE nova.compute.manager [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Traceback (most recent call last): 2014-06-10 00:01:08.347 32223 TRACE nova.compute.manager [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] File "/usr/lib/python2.7/dist-packages/nova/compute/manager.py", line 1118, in _spawn 2014-06-10 00:01:08.347 32223 TRACE nova.compute.manager [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] self._legacy_nw_info(network_info), 2014-06-10 00:01:08.347 32223 TRACE nova.compute.manager [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] File "/usr/lib/python2.7/dist-packages/nova/compute/manager.py", line 703, in _legacy_nw_info 2014-06-10 00:01:08.347 32223 TRACE nova.compute.manager [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] network_info = network_info.legacy() 2014-06-10 00:01:08.347 32223 TRACE nova.compute.manager [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] AttributeError: 'list' object has no attribute 'legacy' 2014-06-10 00:01:08.347 32223 TRACE nova.compute.manager [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] 2014-06-10 00:01:08.919 AUDIT nova.compute.manager [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Terminating instance 2014-06-10 00:01:09.712 32223 ERROR nova.virt.libvirt.driver [-] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] During wait destroy, instance disappeared. 2014-06-10 00:01:09.718 INFO nova.virt.libvirt.firewall [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Attempted to unfilter instance which is not filtered 2014-06-10 00:01:09.719 INFO nova.virt.libvirt.driver [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Deleting instance files /var/lib/nova/instances/2eb5e3ad-3044-41c1-bbb7-10f398f83e43 2014-06-10 00:01:10.044 ERROR nova.compute.manager [req-41e53086-6454-4efb-bb35-a30dc2c780be b3730a52a32e40f0a9500440d1ef1c7d 08cff06d13b74492b780d9ceed699239] [instance: 2eb5e3ad-3044-41c1-bbb7-10f398f83e43] Error: ['Traceback (most recent call last):\n', ' File "/usr/lib/python2.7/dist-packages/nova/compute/manager.py", line 864, in _run_instance\n set_access_ip=set_access_ip)\n', ' File "/usr/lib/python2.7/dist-packages/nova/compute/manager.py", line 1123, in _spawn\n LOG.exception(_(\'Instance failed to spawn\'), instance=instance)\n', ' File "/usr/lib/python2.7/contextlib.py", line 24, in __exit__\n self.gen.next()\n', ' File "/usr/lib/python2.7/dist-packages/nova/compute/manager.py", line 1118, in _spawn\n self._legacy_nw_info(network_info),\n', ' File "/usr/lib/python2.7/dist-packages/nova/compute/manager.py", line 703, in _legacy_nw_info\n network_info = network_info.legacy()\n', "AttributeError: 'list' object has no attribute 'legacy'\n"] 2014-06-10 00:01:40.951 32223 AUDIT nova.compute.resource_tracker [-] Auditing locally available compute resources 2014-06-10 00:01:41.072 32223 AUDIT nova.compute.resource_tracker [-] Free ram (MB): 2861 2014-06-10 00:01:41.072 32223 AUDIT nova.compute.resource_tracker [-] Free disk (GB): 146 2014-06-10 00:01:41.073 32223 AUDIT nova.compute.resource_tracker [-] Free VCPUS: 1 2014-06-10 00:01:41.262 32223 INFO nova.compute.resource_tracker [-] Compute_service record updated for node5:node5.maas ... Can't seem to find any entries in quantum.conf related to "legacy". Any help would be appreciated. Cheers,

  Read the article

• Need help in creating test appliaction in Java and passing parameters into a new designed Java API.

  - by Christophe

  Need help, Please!!! By following the protocol, the Request should be built in 5 byte length, including 1 byte for changing Braud rate (Speed), and send request to a RS-232 port. Protocol: --------------- Request for the command processing, with optional extra byte for changing Baud Rate: LGT : length message ( LGT = 5 ) TYPE : 0x06 TO(time out): 0x0000 CMD : (1 byte) 0x02 application update Baud Rate : (1 byte) 0xNN (optional parameter to change baud rate of the Mnt App) where NN can be: 0x00 = No Baud Rate Change (similar to 4-byte command above) 0x09 = Change to 9600 Baud for Application Update speed 0x0A = Change to 19200 Baud for Application Update speed 0x0E = Change to 115200 Baud for Application Update speed All other bytes are not accepted and will result in a status of 0x01. ------------------ I'm trying to test if my code works or not by creating another class (TestApplication.java) and pass the "3 differenr Baut rate" to this CPXAppliaction. the 3 Baud Rate is supposed to input by reading a file.txt. Question: How do you think these code (first half)? please don't warry about the details about the "sending part". I mean, do I need setter/getter for the "speed" parameter pass? I created the demo test class DemoApp.java (input speed by reading a txt file, and pass into CPXAppliaction). how do you think about that code? Many thanks to you guys!! public class CPXApplication extends CPXCommand { private int speed; . public CPXApplication() { speed = 9600; } public CPXApplication(int speedinit) { speed = speedinit; // TODO: where to get the speed? } protected void buildRequest() throws ElitePortException { String trans = ""; // build the full-qualified message following the protocol trans = addToRequest(trans, (char) 0); trans = addToRequest(trans, (char) 5); trans = addToRequest(trans, (char) 6); trans = addToRequest(trans, (char) 0); trans = addToRequest(trans, (char) 0); trans = addToRequest(trans, (char) 2); switch (speed) { case 9600: trans = addToRequest(trans, (char) 0x09); break; case 19200: trans = addToRequest(trans, (char) 0x0A); break; case 115200: trans = addToRequest(trans, (char) 0x0E); break; default: // TODO: unexpected baud rate. throw(); break; } trans = EncryptBinary(trans); trans = "F0." + trans; wrapRequest(trans); } protected String addToRequest(String req, char c) { return req + c; } protected String addToRequest(String req, String s) { return req + s; } protected String addToRequest(String req) { return req; } public void analyzeResponse() { //.............. } } Here is the demo test code: package com.ingenico.testApp; import com.ingenico.EliteFd.; import java.util.Scanner; import java.io.; class Run { public static void run() { CPXAppliactionUpdate input = new CpXApplicationUpdate(); int lineno = 0; try { FileReader fr = new FileReader("baudRateSpeed.txt"); BufferedReader reader = new BufferedReader(fr); String line = reader.readLine(); Scanner scan = null; while (line != null) { scan = new Scanner(line); String speed; speed = scan.next(); if (lineno == 0) { input.speed = speed; lineno++; } else { input = cpxapplicationupdate(speed, input); } line = reader.readLine(); } reader.close(); } catch (FileNotFoundException e) { System.out.println("Could not find the file"); } catch (IOException e) { System.out.println("Had a problem reading from file"); } } public class DemoApp{ public void main(String args[]) { run(); } } }

  Read the article

• Need help in creating test application in Java and passing parameters into a new designed Java API.

  - by Christophe

  Need help, Please!!! By following the protocol, the Request should be built in 5 byte length, including 1 byte for changing Braud rate (Speed), and send request to a RS-232 port. Protocol: Request for the command processing, with optional extra byte for changing Baud Rate: LGT : length message ( LGT = 5 ) TYPE : 0x06 TO(time out): 0x0000 CMD : (1 byte) 0x02 application update Baud Rate : (1 byte) 0xNN (optional parameter to change baud rate of the Mnt App) where NN can be: 0x00 = No Baud Rate Change (similar to 4-byte command above) 0x09 = Change to 9600 Baud for Application Update speed 0x0A = Change to 19200 Baud for Application Update speed 0x0E = Change to 115200 Baud for Application Update speed All other bytes are not accepted and will result in a status of 0x01. I'm trying to test if my code works or not by creating another class (TestApplication.java) and pass the "3 differenr Baut rate" to this CPXAppliaction. the 3 Baud Rate is supposed to input by reading a file.txt. Question: How do you think these code (first half)? please don't warry about the details about the "sending part". I mean, do I need setter/getter for the "speed" parameter pass? I created the demo test class DemoApp.java (input speed by reading a txt file, and pass into CPXAppliaction). how do you think about that code? Many thanks to you guys!! public class CPXApplication extends CPXCommand { private int speed; . public CPXApplication() { speed = 9600; } public CPXApplication(int speedinit) { speed = speedinit; // TODO: where to get the speed? } protected void buildRequest() throws ElitePortException { String trans = ""; // build the full-qualified message following the protocol trans = addToRequest(trans, (char) 0); trans = addToRequest(trans, (char) 5); trans = addToRequest(trans, (char) 6); trans = addToRequest(trans, (char) 0); trans = addToRequest(trans, (char) 0); trans = addToRequest(trans, (char) 2); switch (speed) { case 9600: trans = addToRequest(trans, (char) 0x09); break; case 19200: trans = addToRequest(trans, (char) 0x0A); break; case 115200: trans = addToRequest(trans, (char) 0x0E); break; default: // TODO: unexpected baud rate. throw(); break; } trans = EncryptBinary(trans); trans = "F0." + trans; wrapRequest(trans); } protected String addToRequest(String req, char c) { return req + c; } protected String addToRequest(String req, String s) { return req + s; } protected String addToRequest(String req) { return req; } public void analyzeResponse() { //.............. } } Here is the demo test code: class Run { public static void run() { CPXAppliaction input = new CpXApplication(); int lineno = 0; try { FileReader fr = new FileReader("baudRateSpeed.txt"); BufferedReader reader = new BufferedReader(fr); String line = reader.readLine(); Scanner scan = null; while (line != null) { scan = new Scanner(line); String speed; speed = scan.next(); if (lineno == 0) { input.speed = speed; lineno++; } else { input = cpxapplication(speed, input); } line = reader.readLine(); } reader.close(); } catch (FileNotFoundException e) { System.out.println("Could not find the file"); } catch (IOException e) { System.out.println("Had a problem reading from file"); } } } public class DemoApp{ public void main(String args[]) { run(); }

  Read the article

< Previous Page | 16 17 18 19 20 21  | Next Page >