Search Results

Search found 2143 results on 86 pages for 'vpn'.

Page 20/86 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

• Cisco ASA dropping IPsec VPN between istself and CentOS server

  - by sebelk

  Currently we're trying to set up an IPsec VPN between a Cisco ASA Version 8.0(4) and a CentOS Linux server. The tunnel comes up successfully, but for some reason that we can't figure out, the firewall is dropping packets from the VPN. The IPsec settings in the ASA sre as follows: crypto ipsec transform-set up-transform-set esp-3des esp-md5-hmac crypto ipsec transform-set up-transform-set2 esp-3des esp-sha-hmac crypto ipsec transform-set up-transform-set3 esp-aes esp-md5-hmac crypto ipsec transform-set up-transform-set4 esp-aes esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map linuxserver 10 match address filtro-encrypt-linuxserver crypto map linuxserver 10 set peer linuxserver crypto map linuxserver 10 set transform-set up-transform-set2 up-transform-set3 up-transform-set4 crypto map linuxserver 10 set security-association lifetime seconds 28800 crypto map linuxserver 10 set security-association lifetime kilobytes 4608000 crypto map linuxserver interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes hash sha group 2 lifetime 28800 crypto isakmp policy 2 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 3 authentication pre-share encryption aes-256 hash md5 group 2 lifetime 86400 crypto isakmp policy 4 authentication pre-share encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 5 authentication pre-share encryption aes-192 hash md5 group 2 group-policy linuxserverip internal group-policy linuxserverip attributes vpn-filter value filtro-linuxserverip tunnel-group linuxserverip type ipsec-l2l tunnel-group linuxserverip general-attributes default-group-policy linuxserverip tunnel-group linuxserverip ipsec-attributes pre-shared-key * Does anyone know where the problem is and how to fix it?

  Read the article

• AWS VPC public web application connecting to database via VPN

  - by Chris

  What I am trying to do is set up a web application that is public facing but makes calls to a database that is on an internal network. I have been trying to set up an AWS VPC with a public subnet, private subnet, and hardware VPN access but I can't seem to get it to work. Can someone help me understand what the process flow here should be? My understanding is that I need a public subnet to handle the website requests and then a private subnet to connect to the VPN but what I do not understand is how to send requests down the chain and get the response. Basically what I am asking is how can I query the database via VPN from that public website? I've tried during rout forwarding but I can't successfully complete the process. Does anyone have any advice on something I can read on this subject or an FAQ on setting something like this up? Is it even possible? I'm out of my league here, this is not my area of expertise but I'm being asked to solve this problem. Any help would be appreciated. Thanks

  Read the article

• Getting SMB file shares working over a PPTP VPN

  - by Ben Scott

  I'm having issues getting SMB file shares working over a PPTP VPN. The server setup consists of a security device (DrayTek V3300) which passes the PPTP authentication to a SBS2003 server running RRAS. The server is the DC and provides DNS and WINS, the single NIC's name server is set to 127.0.0.1, and DHCP on the DrayTek sets the server IP as the DNS. If I create a new VPN connection in Win7, leaving everything as default apart from the server, username, password and domain, I can: ping everything by IP address resolve IPs with nslookup using their fully-qualified name, as in nslookup fileserver.mydomain.local ping machines by fully-qualified name, as in ping fileserver.mydomain.local However if I try to access a file share: within Explorer, I get "Windows cannot access ..." with "Error code: 0x80004005 Unspecified Error", using net use z: \\fileserver.mydomain.local\share, I get "System error 53 has occurred. The network path was not found." If I add the machine name to my HOSTS file I can use the file share, which is my last-ditch workaround, but I have a number of VPN users and would rather a solution that doesn't involve me trying to hand-edit system files on computers half a country away. If I set the WINS server explicitly in the connection's IPv4 settings I don't have to use the FQN to ping the machine, but that doesn't change anything else.

  Read the article

• How to bypass vpn talking to VMWare Guest?

  - by marc esher

  Greetings. Network/VPN n00b question here. I'm running VMWare Workstation with a Guest Windows 2003 Server. It has SQL Server 2000 installed. The sole purpose for this Guest is to house SQL Server... it needn't have internet access or access to any other resources on the network other than the host. When launch Check Point VPN software, the host routes through the company network before it connects to the guest ... i.e. it's no longer a direct connection. I assume this is just how things are supposed to work. However, what's happening is that the connection between my host and the SQL Server instance on the guest intermittently drops. It's not consistent, and some databases on the server will be responsive while others aren't. It appears that the databases with the most traffic on the guest (the ones I'm hitting with load tests) are the ones that become intermittently unresponsive. This problem only manifests when VPN is on; when it's off, I can pound away on this database with no troubles. Thanks for any advice!

  Read the article

• when vpn is connected intenet is not accessible

  - by javapowered

  I need vpn to access certain lan. The problem is - when I connect to vpn intenet stop working. But I need to have access to lan and intenet at the same time. When VPN is connected and I try tracert, I receive "The network is unreachable" message. Sorry about Russian language below, this is copy-pasted from console: C:\Users\Oleg>tracert 173.194.69.102 ??????????? ???????? ? bk-in-f102.1e100.net [173.194.69.102] ? ???????????? ?????? ??????? 30: 1 * * * ???????? ???????? ???????? ??? ???????. 2 1.1.1.1 ????????: ???????? ???? ??????????. ??????????? ?????????. How can I fix this problem?

  Read the article

• VPN on a ubuntu server limited to certain ips

  - by Hultner

  I got an server running Ubuntu Server 9.10 and I need access to it and other parts of my network sometimes when not at home. There's two places I need to access the VPN from. One of the places to an static IP and the other got an dynamic but with DynDNS setup so I can always get the current IP if I want to. Now when it comes to servers people call me kinda paranoid but security is always my number one priority and I never like to allow access to the server outside the network therefor I have two things I have to have on this VPN. One it shouldn't be accessiable from any other IP then these 2 and two it has to use a very secure key so it will be virtually impossible to bruteforce even from the said IP´s. I have no experience what so ever in setting up VPNs, I have used SSH tunneling but never an actuall VPN. So what would be the best, most stable, safest and performance effiecent way to set this up on a Ubuntu Server? Is it possible or should I just set up some kind of SSH Tunnel instead? Thanks on beforehand for answers.

  Read the article

• cannot connect to vpn server (error 721)

  - by callmeblessed

  Hi I got 2 internet connections in my computer. One is using 3.5G HSDPA modem (vodafone huawei e220) and the other using mobile phone (cdma zte c261). Both are using different ISP and i have both. at the moment, i can connect to my office vpn using the HSDPA modem one. But when i tried to use cdma modem (dial up - mobile phone modem), i am just able to get "verifying username and password" and then after a few minutes it display error : Error 721 The Remote Computer didn't respond. I tried to ping into my office ip address, it got good result but still cannot connect to the vpn. I tried to turn off all my firewall (i'm using commodo) and has no response as well. In my cdma mobile phone modem Network connections I tried to allow iNternet connection sharing as well ... and turn on all Internet Protocol TCP/IP, File & Printer Sharing & Client for microsoft networks. But all of my effort has no effect. How to fix this problem ? note: my office using windows vpn as well. thank you .

  Read the article

• Trouble printing to local printer when connected to VPN with split-tunneling enabled

  - by Marve

  I'm a volunteer network admin for a multi-tenant non-profit office space. One of our new tenants uses a VPN to connect to remote resources using RRAS and Small Business Server 2008. They also have a local network printer for the workstations in our office. When connected to the VPN, they cannot print to the local printer. I informed their network admin that they need to enable split-tunneling to fix this. Their network admin enabled split-tunneling, but apparently printing still didn't work. He told me that I need to open port 1723 on our office firewall to allow it to work. I'm just a novice administrator and not familiar with RRAS, but this doesn't sound right to me and I haven't been able to find anything on the web to validate it. Additionally, my understanding of split-tunneling is that it is handled entirely by the VPN client and should work irrespective of firewall settings. Is my understanding of the situation incorrect? What steps should I take to resolve this problem?

  Read the article

• Can't route specific subnet thru VPN in ubuntu

  - by Disco

  I'm having issues routing traffic thru VPN. Here's my setup I have 3 hosts, let's call them A, B and Z B and Z have a VPN connection in the 10.10.10.x SUBNET A and B have a direct connection in the 10.10.12.x SUBNET I want to be able to route traffic from A to Z, like : A <= 10.10.12.254 [LAN] 10.10.12.111 => B <= 10.10.10.152 [VPN] 10.10.10.10 => Z On host B, i have set up ip_forwarding : net.ipv4.ip_forward = 1 and routing on host B: [root@hostA: ~]# ip route 10.10.10.10 dev ppp0 proto kernel scope link src 10.10.10.152 10.10.12.0/24 dev eth1 proto kernel scope link src 10.10.12.111 10.10.10.0/24 dev ppp0 scope link 169.254.0.0/16 dev eth1 scope link routing on host A: [root@hostA: ~]# ip route 10.10.10.0 via 10.10.12.111 dev eth1 10.10.12.0/24 dev eth1 proto kernel scope link src 10.10.12.254 169.254.0.0/16 dev eth1 scope link default via 192.168.1.1 dev eth0 But still not able to ping 10.10.10.10 from host A. Any idea ? I'm pulling my hairs out.

  Read the article

• Checkpoint VPN-1 R60 and Windows 7 64 Bit Client

  - by Mohit

  Hi All, As per my knowledge of checkpoint VPN-1. My company is using checkpoint VPN-1 R 60 ( I guess as I dont know how to check server version) Firewall(VPN Server). Now the problem is that I installed Windows 7 64 bit. But, after my research I found that there are not even one client (SecuRemote/SecuClient) for Win7 64 bit, when Firewall or server is R60. I thought of some open source solutions. Can you guys please suggest me some with the configuration required. As of now, I know the IP of the server. I know my username and password using which I connect and that is not my domain password. that i can confirm to you guys. I am not a network guy. I am more of a developer. But, I need some help in this.So, let me know if I can provide you more details. Please please i need urgent help on this.

  Read the article

• Windows VPN always disconnects after < 3 minutes, only from my network

  - by hemp

  First, this problem has existed for almost two years. Until serverfault was born, I pretty much gave up on solving it - but now, hope is reborn! I've set up a Windows 2003 server as a domain controller and VPN server at a remote office. I am able to connect to and work over the VPN from every windows client I've tried, including XP, Vista, and Windows 7 without issue, from at least five different networks (corporate and home, domain and non.) It works fine from all of them. However, whenever I connect from clients on my home network, the connection drops (silently) after 3 minutes or less. After a short while, it will eventually tell me the connection has dropped and attempt to redial/reconnect (if I've configured the client that way.) If I reconnect, the connection will re-establish and appear to work correctly, but again will silently drop, this time after a seemingly shorter time period. These are not intermittent drops. It happens every single time, in exactly the same way. The only variable is how long the connection survives. It doesn't matter what type of traffic I send. I can sit idle, send continuous pings, RDP, transfer files, all of that at once - it makes no difference. The result is always the same. Connected for a few minutes, then silent death. Since I doubt anyone has experienced this exact situation, what steps can I take to troubleshoot my evanescing VPN?

  Read the article

• Problem connecting to remote network using demand-dial VPN interface with Windows Server 2003

  - by Mike Forman

  I have a Windows 2003 server (SP2) that I'm trying to set up route traffic from my local network using a VPN My local network has the following components: Broadband router (192.168.0.1) Windows Server with a single NIC running RRAS (192.168.0.2 def. gateway = 192.168.0.1) Client Machine (192.168.0.3 def. gateway = 192.168.0.1) Using a VPN connection, I am trying to access a remote machine (10.0.0.1 for example) I configured RRAS with a demand-dial interface for the VPN and set it to be a persistent connection. As part of that setup, a static route to 10.0.0.0 (255.255.0.0) was created. When at the console of the server, I can ping 10.0.0.1 with no problems I added a route on the client machine using the following command: ROUTE ADD 10.0.0.0 MASK 255.255.0.0 192.168.0.2 If I run tracert 10.0.0.1 from the client, the first hop is to 192.168.0.2 which tells me that route is working. However, I cannot ping 10.0.0.1 from the client machine. What am I missing? Hopefully something simple.

  Read the article

• Remote network traffic not passing through VPN

  - by John Virgolino

  We have the following topology: LAN A LAN B LAN C 10.14.0.0/16 <-VPN-> 10.18.0.0/16 --- SONICWALL <-VPN-> M0N0WALL --- 10.32.0.0/16 Traffic between LAN A and LAN B works perfectly. Traffic between LAN C and LAN B works perfectly. Traffic between LAN A and LAN C, not so much. LAN A's gateway has a route to LAN C that points to the Sonicwall. The Sonicwall has a route to LAN A pointing to the VPN gateway connecting LAN B to LAN A. Tracing packets on the Sonicwall shows the LAN C destined traffic to arrive on the Sonicwall, but it does not forward the traffic, it dies there. Traffic from LAN B gets forwarded. Tracing packets on the Sonicwall while sending traffic from LAN C destined for LAN A shows nothing. This tells me that the M0N0WALL is not forwarding traffic for the 10.14.0.0 network and the Sonicwall is not forwarding from 10.14.0.0. The SA on the Sonicwall terminates on the WAN ZONE and is defined to use an address group that incorporates both the 10.14.0.0 and 10.18.0.0 networks. The M0N0WALL is configured for the 10.18.0.0 network and I have tried with both a static route to 10.14.0.0 and without on the M0N0WALL. I tried manually adding the 10.14.0.0 network to the SA on the M0N0WALL, but that really aggravated it and the SA never came up, so I reverted. I have checked all the firewall rules to make sure nothing is blocked. All of the Sonicwall auto-added rules look right. Specs: Sonicwall TZ200, Enhanced OS M0N0WALL v1.32 I'm at a loss at this point. Any help would be appreciated.

  Read the article

• Is the Windows VPN secure?

  - by Tor Haugen

  I have used a few VPN solutions over the years. Most are hard to set up, slow to connect and/or rather ill-behaved (replacing system drivers, disrupting each other etc). One solution I have never used earlier is the one built into Windows. This is mostly because the infrastructure guys always refuse to use it because they claim it's 'not secure'. Now I have finally had the chance to use it (on Windows 7), and wow, it's a breeze! Easy to set up, well-behaved, it connects almost instantly, automatically authenticates with my logged-in credentials, and integrates excellently with the UI. I have to say, unless it really isn't secure, I'll be happy if I never have to use another VPN product ever again. I gather the Windows VPN used to rely on PPTP, which is not considered secure. But in Windows 7/2008, it supports L2TP/IPSec, SSTP and IKEv2, and authenticates with EAP or CHAP/CHAPv2. That seems pretty up-to-date to me. But I'm just a lowly developer. Can someone in the know give me the lowdown on this?

  Read the article

• VPN with VLANs? [closed]

  - by Craig

  As usual, I'm sure I'm in way over my head on this one. My networking skills are limited; so, bear with me if you will. What I have are a few testing servers at my house as well as at a friends house that I want to link together so they can see each other (VPN right? I've done those before). We want to be able to see all the servers and work with them from either location. All the servers also need to be able to see each other. But, we don't want to see each others PCs, printers, PS3s etc. How do we pull that trick off? Multiple VLAN?... subnets?... what? If hardware matters, I have an old PC I was planning on loading pfSense onto because my current el-cheapo router doesn't support VPN. The VPN linking the houses is about the only thing I'm sure on. Beyond that, I'm lost. I'm not a complete noob; but, like I said, I'm not so sharp with the more complex networking. I do however read well... So use lots of descriptive words and feel free to link away to long dry articles if necessary. :-)

  Read the article

• Local traffic through VPN, global traffic through WAN

  - by ikonoma

  I have an issue with my internet connection. I am using VPN (Aventail Client) to access the local resources. When connected to VPN the Internet traffic passes through it, not through my LAN or Wi-Fi network. I would like to change the routing table to use the Wi-Fi adapter of the PC for WAN traffic. I have routing file, which works very well and routes the traffic in this way, but only when I am physically connected to the local network through LAN. But I can't set it to work with the VPN connection, because I have no gateway when I am connected to it. Etc this in bold is missing. What to do? route change 0.0.0.0 mask 0.0.0.0 172.16.76.1 metric 200 if 12 route change 0.0.0.0 mask 0.0.0.0 10.44.2.1 metric 400 if 11 route add 150.251.0.0 mask 255.255.0.0 10.44.2.1 metric 100 if 11 route add 10.0.0.0 mask 255.0.0.0 10.44.2.1 metric 100 if 11 pause

  Read the article

• Tunnel is up but cannot ping directly connected network

  - by drmanalo

  We configured a site-to-site VPN and here is the topology. I control the network on the left but not the one on the right. All devices in our network has public IPs. Server---ASA5505---Cisco887======Internet=====ASA5510---devices I can see the tunnel is up and can do extended ping using a loopback interface. From the 10.175 and 10.165 networks, they can also ping my loopback address. I can also dial in using a Cisco VPN client, and can connect to the devices on the right. #show crypto session Crypto session current status Interface: Vlan3 Profile: xxx-profile Session status: UP-ACTIVE Peer: 213.121.x.x port 500 IKEv1 SA: local 77.245.x.x/500 remote 213.121.x.x/500 Active IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.175.0.0/255.255.128.0 Active SAs: 0, origin: crypto map IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.165.0.0/255.255.192.0 Active SAs: 2, origin: crypto map #ping 10.165.29.39 source loopback 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.165.29.39, timeout is 2 seconds: Packet sent with a source address of 10.0.20.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 16/17/20 ms My problem is the devices on the right cannot reach my server. They could only ping the loopback address and nothing else. I'm pasting some diagnostics related to routing thinking perhaps routing is my issue. I can paste all the running-config on my side of network if needed. #show ip int brief Interface IP-Address OK? Method Status Protocol ATM0 unassigned YES NVRAM administratively down down Ethernet0 unassigned YES NVRAM administratively down down FastEthernet0 unassigned YES unset up up connected to ASA FastEthernet1 unassigned YES unset administratively down down FastEthernet2 unassigned YES unset administratively down down FastEthernet3 unassigned YES unset up up Loopback1 10.0.20.65 YES NVRAM up up Loopback2 10.0.20.1 YES NVRAM up up Virtual-Template1 77.245.x.x YES unset up down Virtual-Template2 77.245.x.x YES unset up down Vlan1 unassigned YES unset down down Vlan3 77.245.x.x YES NVRAM up up connected to the Internet #show run | section ip route ip route 0.0.0.0 0.0.0.0 77.245.x.x ip route 213.121.240.36 255.255.255.255 Vlan3 #show access-list Extended IP access list 102 10 permit ip 10.0.20.0 0.0.0.15 10.175.0.0 0.0.127.255 (3332 matches) 20 permit ip 10.0.20.0 0.0.0.15 10.165.0.0 0.0.63.255 (3498 matches) #show vlan-switch VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active 3 VLAN0003 active Fa0, Fa1, Fa2, Fa3 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup #show ip route Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP + - replicated route, % - next hop override Gateway of last resort is 77.245.x.x to network 0.0.0.0 S* 0.0.0.0/0 [1/0] via 77.245.x.x 10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks C 10.0.20.0/28 is directly connected, Loopback2 L 10.0.20.1/32 is directly connected, Loopback2 C 10.0.20.64/28 is directly connected, Loopback1 L 10.0.20.65/32 is directly connected, Loopback1 S 10.165.0.0/18 [1/0] via 213.121.x.x 77.0.0.0/8 is variably subnetted, 3 subnets, 3 masks S 77.0.0.0/8 [1/0] via 77.245.x.x C 77.245.x.x/29 is directly connected, Vlan3 L 77.245.x.x/32 is directly connected, Vlan3 213.121.x.0/32 is subnetted, 1 subnets S 213.121.x.x is directly connected, Vlan3 I read some of the posts here which lead to NATing issue but I'not sure of my next step. Should I translate my public address to private and route it to the loopback address? (only guessing) CISCO VPN site to site Site-to-Site VPN between two ASA 5505s only working in one direction Hope someone could help. Thanks in advance!

  Read the article

• Site-to-site VPN using MD5 instead of SHA and getting regular disconnection

  - by Steven

  We are experiencing some strange behavior with a site-to-site IPsec VPN that goes down about every week for 30 minutes (Iam told 30 minutes exactly). I don't have access to the logs, so it's difficult to troubleshoot. What is also strange is that the two VPN devices are set to use SHA hash algorithm but apparently end up agreeing to use MD5. Does anybody have a clue? or is this just insufficient information? Edit: Here is an extract of the log of one of the two VPN devices, which is a Cisco 3000 series VPN concentrator. 27981 03/08/2010 10:02:16.290 SEV=4 IKE/41 RPT=16120 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27983 03/08/2010 10:02:56.930 SEV=4 IKE/41 RPT=16121 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27986 03/08/2010 10:03:35.370 SEV=4 IKE/41 RPT=16122 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) [… same continues for another 15 minutes …] 28093 03/08/2010 10:19:46.710 SEV=4 IKE/41 RPT=16140 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28096 03/08/2010 10:20:17.720 SEV=5 IKE/172 RPT=1291 xxxxxxxx Group [xxxxxxxx] Automatic NAT Detection Status: Remote end is NOT behind a NAT device This end IS behind a NAT device 28100 03/08/2010 10:20:17.820 SEV=3 IKE/134 RPT=79 xxxxxxxx Group [xxxxxxxx] Mismatch: Configured LAN-to-LAN proposal differs from negotiated proposal. Verify local and remote LAN-to-LAN connection lists. 28103 03/08/2010 10:20:17.820 SEV=4 IKE/119 RPT=1197 xxxxxxxx Group [xxxxxxxx] PHASE 1 COMPLETED 28104 03/08/2010 10:20:17.820 SEV=4 AUTH/22 RPT=1031 xxxxxxxx User [xxxxxxxx] Group [xxxxxxxx] connected, Session Type: IPSec/LAN- to-LAN 28106 03/08/2010 10:20:17.820 SEV=4 AUTH/84 RPT=39 LAN-to-LAN tunnel to headend device xxxxxxxx connected 28110 03/08/2010 10:20:17.920 SEV=5 IKE/25 RPT=1291 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28113 03/08/2010 10:20:17.920 SEV=5 IKE/24 RPT=88 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28116 03/08/2010 10:20:17.920 SEV=5 IKE/66 RPT=1290 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28117 03/08/2010 10:20:17.930 SEV=5 IKE/25 RPT=1292 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28120 03/08/2010 10:20:17.930 SEV=5 IKE/24 RPT=89 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28123 03/08/2010 10:20:17.930 SEV=5 IKE/66 RPT=1291 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28124 03/08/2010 10:20:18.070 SEV=4 IKE/173 RPT=17330 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices. 28127 03/08/2010 10:20:18.070 SEV=4 IKE/49 RPT=17332 xxxxxxxx Group [xxxxxxxx] Security negotiation complete for LAN-to-LAN Group (xxxxxxxx) Responder, Inbound SPI = 0x56a4fe5c, Outbound SPI = 0xcdfc3892 28130 03/08/2010 10:20:18.070 SEV=4 IKE/120 RPT=17332 xxxxxxxx Group [xxxxxxxx] PHASE 2 COMPLETED (msgid=37b3b298) 28131 03/08/2010 10:20:18.750 SEV=4 IKE/41 RPT=16141 xxxxxxxx Group [xxxxxxxx] IKE Initiator: New Phase 2, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28135 03/08/2010 10:20:18.870 SEV=4 IKE/173 RPT=17331 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices.

  Read the article

• Dynamic DNS registration for VPN clients

  - by Eric Falsken

  I've got a VPN server set up in my Active Directory on a remote network. (VPN Server is separate box from DNS/AD) When I dial into the network (client machine is not a member of the AD) the machine does not register its IP or Hostname in the DNS. I've played with all possible combinations of DHCP and RRAS-allocated IP pools, and none of them seem to cause my client to register. Is it because my client has to be a member of the domain? Are there some security settins I can tweak so that it can register its hostname/ip? I've looked in the event logs (System and Security) for the AD, DNS, DHCP, RRAS, and the client machine, and don't see anything relating to DNS Registration. Here's the IPConfig on the client machine (once connected): PPP adapter My VPN Name: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : My VPN Name Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.22(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.1.52 <- DC1 192.168.1.53 <- DC2 NetBIOS over Tcpip. . . . . . . . : Enabled

  Read the article

• Cisco ASA: Allowing and Denying VPN Access based on membership to an AD group

  - by milkandtang

  I have a Cisco ASA 5505 connecting to an Active Directory server for VPN authentication. Usually we'd restrict this to a particular OU, but in this case users which need access are spread across multiple OUs. So, I'd like to use a group to specify which users have remote access. I've created the group and added the users, but I'm having trouble figuring out how to deny users which aren't in that group. Right now, if someone connects they get assigned the correct group policy "companynamera" if they are in that group, so the LDAP mapping is working. However, users who are not in that group still authenticate fine, and their group policy becomes the LDAP path of their first group, i.e. CN=Domain Users,CN=Users,DC=example,DC=com, and then are still allowed access. How do I add a filter so that I can map everything that isn't "companynamera" to no access? Config I'm using (with some stuff such as ACLs and mappings removed, since they are just noise here): gateway# show run : Saved : ASA Version 8.2(1) ! hostname gateway domain-name corp.company-name.com enable password gDZcqZ.aUC9ML0jK encrypted passwd gDZcqZ.aUC9ML0jK encrypted names name 192.168.0.2 dc5 description FTP Server name 192.168.0.5 dc2 description Everything server name 192.168.0.6 dc4 description File Server name 192.168.0.7 ts1 description Light Use Terminal Server name 192.168.0.8 ts2 description Heavy Use Terminal Server name 4.4.4.82 primary-frontier name 5.5.5.26 primary-eschelon name 172.21.18.5 dmz1 description Kerio Mail Server and FTP Server name 4.4.4.84 ts-frontier name 4.4.4.85 vpn-frontier name 5.5.5.28 ts-eschelon name 5.5.5.29 vpn-eschelon name 5.5.5.27 email-eschelon name 4.4.4.83 guest-frontier name 4.4.4.86 email-frontier dns-guard ! interface Vlan1 nameif inside security-level 100 ip address 192.168.0.254 255.255.255.0 ! interface Vlan2 description Frontier FiOS nameif outside security-level 0 ip address primary-frontier 255.255.255.0 ! interface Vlan3 description Eschelon T1 nameif backup security-level 0 ip address primary-eschelon 255.255.255.248 ! interface Vlan4 nameif dmz security-level 50 ip address 172.21.18.254 255.255.255.0 ! interface Vlan5 nameif guest security-level 25 ip address 172.21.19.254 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 switchport access vlan 3 ! interface Ethernet0/2 switchport access vlan 4 ! interface Ethernet0/3 switchport access vlan 5 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone PST -8 clock summer-time PDT recurring dns domain-lookup inside dns server-group DefaultDNS name-server dc2 domain-name corp.company-name.com same-security-traffic permit intra-interface access-list companyname_splitTunnelAcl standard permit 192.168.0.0 255.255.255.0 access-list companyname_splitTunnelAcl standard permit 172.21.18.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip any 172.21.20.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip any 172.21.18.0 255.255.255.0 access-list bypassingnat_dmz extended permit ip 172.21.18.0 255.255.255.0 192.168.0.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 12288 logging buffered warnings logging asdm notifications mtu inside 1500 mtu outside 1500 mtu backup 1500 mtu dmz 1500 mtu guest 1500 ip local pool VPNpool 172.21.20.50-172.21.20.59 mask 255.255.255.0 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface global (outside) 2 email-frontier global (outside) 3 guest-frontier global (backup) 1 interface global (dmz) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 2 dc5 255.255.255.255 nat (inside) 1 192.168.0.0 255.255.255.0 nat (dmz) 0 access-list bypassingnat_dmz nat (dmz) 2 dmz1 255.255.255.255 nat (dmz) 1 172.21.18.0 255.255.255.0 access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 4.4.4.1 1 track 1 route backup 0.0.0.0 0.0.0.0 5.5.5.25 254 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 ldap attribute-map RemoteAccessMap map-name memberOf IETF-Radius-Class map-value memberOf CN=RemoteAccess,CN=Users,DC=corp,DC=company-name,DC=com companynamera dynamic-access-policy-record DfltAccessPolicy aaa-server ActiveDirectory protocol ldap aaa-server ActiveDirectory (inside) host dc2 ldap-base-dn dc=corp,dc=company-name,dc=com ldap-scope subtree ldap-login-password * ldap-login-dn cn=administrator,ou=Admins,dc=corp,dc=company-name,dc=com server-type microsoft aaa-server ADRemoteAccess protocol ldap aaa-server ADRemoteAccess (inside) host dc2 ldap-base-dn dc=corp,dc=company-name,dc=com ldap-scope subtree ldap-login-password * ldap-login-dn cn=administrator,ou=Admins,dc=corp,dc=company-name,dc=com server-type microsoft ldap-attribute-map RemoteAccessMap aaa authentication enable console LOCAL aaa authentication ssh console LOCAL http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart sla monitor 123 type echo protocol ipIcmpEcho 4.4.4.1 interface outside num-packets 3 frequency 10 sla monitor schedule 123 life forever start-time now crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 ! track 1 rtr 123 reachability telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 5 ssh version 2 console timeout 0 management-access inside dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy companynamera internal group-policy companynamera attributes wins-server value 192.168.0.5 dns-server value 192.168.0.5 vpn-tunnel-protocol IPSec password-storage enable split-tunnel-policy tunnelspecified split-tunnel-network-list value companyname_splitTunnelAcl default-domain value corp.company-name.com split-dns value corp.company-name.com group-policy companyname internal group-policy companyname attributes wins-server value 192.168.0.5 dns-server value 192.168.0.5 vpn-tunnel-protocol IPSec password-storage enable split-tunnel-policy tunnelspecified split-tunnel-network-list value companyname_splitTunnelAcl default-domain value corp.company-name.com split-dns value corp.company-name.com username admin password IhpSqtN210ZsNaH. encrypted privilege 15 tunnel-group companyname type remote-access tunnel-group companyname general-attributes address-pool VPNpool authentication-server-group ActiveDirectory LOCAL default-group-policy companyname tunnel-group companyname ipsec-attributes pre-shared-key * tunnel-group companynamera type remote-access tunnel-group companynamera general-attributes address-pool VPNpool authentication-server-group ADRemoteAccess LOCAL default-group-policy companynamera tunnel-group companynamera ipsec-attributes pre-shared-key * ! class-map type inspect ftp match-all ftp-inspection-map class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect ftp ftp-inspection-map parameters class ftp-inspection-map policy-map type inspect dns migrated_dns_map_1 parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns migrated_dns_map_1 inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect ils inspect netbios inspect rsh inspect rtsp inspect skinny inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp inspect icmp inspect icmp error inspect esmtp inspect pptp ! service-policy global_policy global prompt hostname context Cryptochecksum:487525494a81c8176046fec475d17efe : end gateway# Thanks so much!

  Read the article

• Is it possible to add a notification message when a VPN gets connected?

  - by digitaljail

  I'm using Ubuntu 10.04 and I use to connect to a pptp VPN, everything works perfectly, when i start my VPN connection I can see that the connection is in progress from the NetworkManager icon, and I can see that the connection is on when the Network icon gets the small lock. Is it possible to add a notification ballon, like the one I see when the network connection is estabilished? P.s if the connection fail or is dropped, the notification cames out like this:

  Read the article

• How to route certain applications through a VPN and others to use my 'standard' connection in OSX 10.6?

  - by Alfie

  I am currently working abroad and use my company's VPN for FTP and some browsing. This is a relatively slow connection and while it is suitable for those VPN necessities; much of my other internet usage can be done without the VPN at a much higher speed. Is there a way to tell Safari and my FTP software to use the VPN and for all other connections to go directly to the internet. I am currently using OSX's Network Prefs for running my VPN connection. Ta

  Read the article

• Two wireless NICs on a MacBook - can I bind all VPN traffic to one, and everything else to another?

  - by Ben Aston

  I frequently connect to my workplace over a VPN. I would like to continue watching videos from, say YouTube, whilst I work on the VPN, without degrading the available VPN bandwidth (say for an RDP session). Can I configure a second NIC to deal with only the VPN traffic, with everything else going over the primary? Specs as requested: Macbook Pro, OSX Snow Leopard, using the built in OSX VPN connectivity, the in-built airport card and a USB external wifi adapter.

  Read the article

• Cisco VPN error 403: Unable to contact the security gateway

  - by mtashev

  I'm trying to make a connection via Cisco VPN Client (version is 5.0.07.0290), but i get the below mentioned error. I have to say that i'm using Windows 8. "Secure VPN Connection terminated locally by the Client. Reason 403: Unable to contact the security gateway." I've tried several fixes, but none of them worked. The display name in regedit is the correct, and my certificates are ok as well. If i switch to TCP (the default is UDP) i get error 414. Firewall is off. Any suggestions will be appreciated.

  Read the article

• OpenVPN DNS: VPN DNS stomping local VPN

  - by Eddie Parker

  I've finally noodled with OpenVPN enough to get it working. Even better, I can mount samba drives, ping network machines through the TUN device, etc - it's all great. However, I'm noticing that if I have the directive: push "dhcp-option DNS 10.0.1.1" # Push our local DNS to clients Then some of the machines that are normally visible by the client, on the client's side (i.e., not through the VPN) get masked with some other server out on the Internet. Is there any way to avoid this, besides hacking the 'hosts' file on the client machine? Ideally I'd like to only use my VPN's DNS for machines within that domain.

  Read the article

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >