Search Results

Search found 1900 results on 76 pages for 'xserve raid'.

Page 20/76 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

• Western Digital My Book not recognized by WD software

  - by Kari

  A few years ago I bought a WD My Book Pro 2. It worked fine for a while, then one of the drives failed and I sent it back to be replaced under warranty. I never got around to setting up the new one when I got it back. I finally ran out of room on my internal drive, so I tried to use the external - no go. Both drives spin up, but aren't recognized by either Disk Utility (Mac) or the WD Drive Manager. I tried on a PC as well with fresh software. Then I pulled the drives out of the enclosure (warranty is already expired) and plugged them straight into the PC. Both recognized and working 100% in RAID0. BIOS recognizes either disk as functional; Windows only sees them when both are connected due to the RAID which I can't change without the WD software. The drives that were returned to me are the "Green" drives which I've read are NOT recommended for RAID. Is it possible that this is interfering with them reading externally? Any other ideas? My main computer is a laptop so using them internally isn't an option :(

  Read the article

• Setup access to SAS RAID drives with NTFS partitions on CentOS Machine

  - by Quanano

  We have a Dell Poweredge 2900 system with Adaptec 39320A SCSI CONTROLLER CARD and 4 SAS hard drives attached, with NTFS partitions on them. We installed CentOS on the other raid array with a different controller and it is working fine. We are now trying to access the drives shown above and they are not being shown in /dev as sdb, etc. sda is the drive that we installed centos on and it has sda1, sda2, sda3, etc. The CDROM has been picked up as well. If I scan for scsi devices then the perc and adaptec controllers are both found. sg0 is the CDROM and sg2 is the centos installed, however I think sg1 is the other drive but I cannot see anyway to mount the partitions, as only the drive is listed in /dev. Thanks. EXTRA INFO fdisk -l Disk /dev/sda: 72.7 GB, 72746008576 bytes 255 heads, 63 sectors/track, 8844 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x11e3119f Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 8845 70528000 8e Linux LVM Disk /dev/mapper/vg_lal2server-lv_root: 34.4 GB, 34431041536 bytes 255 heads, 63 sectors/track, 4186 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_root doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_swap: 21.1 GB, 21139292160 bytes 255 heads, 63 sectors/track, 2570 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_swap doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_home: 16.6 GB, 16647192576 bytes 255 heads, 63 sectors/track, 2023 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_home doesn't contain a valid partition table These are all from the install hdd not the additional hard drives modprobe a320raid FATAL: Module a320raid not found. lsscsi -v [0:0:0:0] cd/dvd TSSTcorp CDRWDVD TS-H492C DE02 /dev/sr0 dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0] [4:0:10:0] enclosu DP BACKPLANE 1.05 - dir: /sys/bus/scsi/devices/4:0:10:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:0:10/4:0:10:0] [4:2:0:0] disk DELL PERC 5/i 1.03 /dev/sda dir: /sys/bus/scsi/devices/4:2:0:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:2:0/4:2:0:0] . lsmod Module Size Used by fuse 66285 0 des_generic 16604 0 ecb 2209 0 md4 3461 0 nls_utf8 1455 0 cifs 278370 0 autofs4 26888 4 ipt_REJECT 2383 0 ip6t_REJECT 4628 2 nf_conntrack_ipv6 8748 2 nf_defrag_ipv6 12182 1 nf_conntrack_ipv6 xt_state 1492 2 nf_conntrack 79453 2 nf_conntrack_ipv6,xt_state ip6table_filter 2889 1 ip6_tables 19458 1 ip6table_filter ipv6 322029 31 ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6 bnx2 79618 0 ses 6859 0 enclosure 8395 1 ses dcdbas 9219 0 serio_raw 4818 0 sg 30124 0 iTCO_wdt 13662 0 iTCO_vendor_support 3088 1 iTCO_wdt i5000_edac 8867 0 edac_core 46773 3 i5000_edac i5k_amb 5105 0 shpchp 33482 0 ext4 364410 3 mbcache 8144 1 ext4 jbd2 88738 1 ext4 sd_mod 39488 3 crc_t10dif 1541 1 sd_mod sr_mod 16228 0 cdrom 39771 1 sr_mod megaraid_sas 77090 2 aic79xx 129492 0 scsi_transport_spi 26151 1 aic79xx pata_acpi 3701 0 ata_generic 3837 0 ata_piix 22846 0 radeon 1023359 1 ttm 70328 1 radeon drm_kms_helper 33236 1 radeon drm 230675 3 radeon,ttm,drm_kms_helper i2c_algo_bit 5762 1 radeon i2c_core 31276 4 radeon,drm_kms_helper,drm,i2c_algo_bit dm_mirror 14101 0 dm_region_hash 12170 1 dm_mirror dm_log 10122 2 dm_mirror,dm_region_hash dm_mod 81500 11 dm_mirror,dm_log

  Read the article

• How can I fix my corrupted RAID1 ext4 partition on a Synology DS212 NAS?

  - by Neil

  I have two identical 3 TB disks that were in a RAID1 array, where one disk crashed. I replaced the failed disk, but not after the RAID partitions got messed up. I need to figure out how to restore the RAID array and get at my ext4 partition. Here are the properties of the surviving disk: # fdisk -l /dev/sda fdisk: device has more than 2^32 sectors, can't use all of them Disk /dev/sda: 2199.0 GB, 2199023255040 bytes 255 heads, 63 sectors/track, 267349 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 267350 2147483647+ ee EFI GPT # parted /dev/sda print Model: ATA ST3000DM001-9YN1 (scsi) Disk /dev/sda: 3001GB Sector size (logical/physical): 512B/512B Partition Table: gpt Disk Flags: Number Start End Size File system Name Flags 1 131kB 2550MB 2550MB ext4 raid 2 2550MB 4698MB 2147MB linux-swap(v1) raid 5 4840MB 3001GB 2996GB raid I replaced the failed drive, and cloned the surviving drive to it so I have something to work with. I cloned the drives with dd if=/dev/sdb of=/dev/sda conv=noerror bs=64M, and now /dev/sda and /dev/sdb are identical. Here is the RAID information: # cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] md1 : active raid1 sdb2[1] 2097088 blocks [2/1] [_U] md0 : active raid1 sdb1[1] 2490176 blocks [2/1] [_U] unused devices: <none> It seems that md2 is missing. Here is what testdisk 6.14-WIP finds: Disk /dev/sda - 3000 GB / 2794 GiB - CHS 364801 255 63 Current partition structure: Partition Start End Size in sectors 1 P Linux Raid 256 4980735 4980480 [md0] 2 P Linux Raid 4980736 9175039 4194304 [md1] Invalid RAID superblock 5 P Linux Raid 9453280 5860519007 5851065728 5 P Linux Raid 9453280 5860519007 5851065728 # After a quick search Disk /dev/sda - 3000 GB / 2794 GiB - CHS 364801 255 63 Partition Start End Size in sectors D MS Data 256 4980607 4980352 [1.41.12-2197] D Linux Raid 256 4980735 4980480 [md0] D Linux Swap 4980736 9174895 4194160 D Linux Raid 4980736 9175039 4194304 [md1] >P MS Data 9481056 5858437983 5848956928 [1.41.12-2228] And listing the files on the last partition in the list shows all of my files intact. What should I do?

  Read the article

• Will this RAID5 setup work (3TB Seagate Barracudas + Adaptec RAID 6405)?

  - by Slayer537

  As the title states, will this RAID combo work, and if not what needs to be changed? Overall opinions would be most helpful. I currently run a small file server of about 5TB or so. I keep outgrowing my needs and need to build a RAID setup that will allow me to expand as needed. I am new to RAID setups, especially one of the scale I have currently planned out, but I have being doing some research for the past couple of weeks and have come up with a build. Ideally, I'd have the setup completely built, but I'd like to keep the total cost around $1k and can't afford to go above $1.5k, so unfortunately that's not an option. 2 of my current drives are WD Caviar Blacks 2TB; however, I have recently learned that due to the lack of TLER those drives are awful for any RAID setup other than 0 or 1. That being said, my third drive is a Seagate Barracuda 3TB (ST300DM001) and I have found a RAID controller that states it supports it, so I'd like to use this same type of drive, if possible. Have any of you had any experience using this drive or a similar one in a RAID5 configuration? The manufacturer states that it supports it, but knowing that it is not an enterprise drive, I am slightly concerned that it could drop out of the array. I would just go with enterprise drives, but those are about double in cost... Parts list: Storage rack: http://www.ebay.com/itm/SGI-3U-Media-Storage-Server-16-Hard-Drive-Bay-SATA-SAS-Expander-Omnistor-SE3016-/140735776937?pt=LH_DefaultDomain_0&hash=item20c48188a9 3 more HDs (for now..): http://www.amazon.com/Seagate-Barracuda-3-5-Inch-Internal-ST3000DM001/dp/B005T3GRLY/ref=dp_return_2?ie=UTF8&n=172282&s=electronics Adaptec RAID 6405: http://www.newegg.com/Product/Product.aspx?Item=N82E16816103224 here's a link to the compatibility sheet if that helps: http://download.adaptec.com/pdfs/compatibility_report/arc-sas_cr_03-27-12_series6.pdf SAS expander cable: http://www.pc-pitstop.com/sas_cables_adapters/8887-2M.asp My plan is to install the RAID card in my computer and then route the SAS cable to the rack. Setup a RAID5 on 3 drives, transfer my data over from my other drive, and then add that drive to the array. Eventually, I'd like to get a 2U unit and run the file server on that and move the RAID card over to there, but that will have to happen later on. Side note: The computer the card would be going into will be running Windows 7 Pro with 24GB of DDR3-1600 and an i7-930.

  Read the article

• Hard drives indication with controller MegaRAID SAS 9261-8i on HP Proliant DL320e Gen8. Is it possible?

  - by ame

  Give me advice, please. My situation: There're the server HP ProLiant DL320e Gen8 and MegaRAID SAS 9261-8i RAID Controller. I installed Controller into server and I reconnected Mini-SAS cord from block of hard drives to controller, but I haven't any indication of hard discs on server front panel. There's indication of activity of drives only during boot of server. Controller has 2-pin connector (JT6B3, SAS Activity LED header) but where and how can I connect it? Thanx.

  Read the article

• How do I tell mdadm to start using a missing disk in my RAID5 array again?

  - by Jon Cage

  I have a 3-disk RAID array running in my Ubuntu server. This has been running flawlessly for over a year but I was recently forced to strip, move and rebuild the machine. When I had it all back together and ran up Ubuntu, I had some problems with disks not being detected. A couple of reboots later and I'd solved that issue. The problem now is that the 3-disk array is showing up as degraded every time I boot up. For some reason it seems that Ubuntu has made a new array and added the missing disk to it. I've tried stopping the new 1-disk array and adding the missing disk, but I'm struggling. On startup I get this: root@uberserver:~# cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md_d1 : inactive sdf1[2](S) 1953511936 blocks md0 : active raid5 sdg1[2] sdc1[3] sdb1[1] sdh1[0] 2930279808 blocks level 5, 64k chunk, algorithm 2 [4/4] [UUUU] I have two RAID arrays and the one that normally pops up as md1 isn't appearing. I read somewhere that calling mdadm --assemble --scan would re-assemble the missing array so I've tried first stopping the existing array that ubuntu started: root@uberserver:~# mdadm --stop /dev/md_d1 mdadm: stopped /dev/md_d1 ...and then tried to tell ubuntu to pick the disks up again: root@uberserver:~# mdadm --assemble --scan mdadm: /dev/md/1 has been started with 2 drives (out of 3). So that's started md1 again but it's not picking up the disk from md_d1: root@uberserver:~# cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md1 : active raid5 sde1[1] sdf1[2] 3907023872 blocks level 5, 64k chunk, algorithm 2 [3/2] [_UU] md_d1 : inactive sdd1[0](S) 1953511936 blocks md0 : active raid5 sdg1[2] sdc1[3] sdb1[1] sdh1[0] 2930279808 blocks level 5, 64k chunk, algorithm 2 [4/4] [UUUU] What's going wrong here? Why is Ubuntu trying to pick up sdd into a different array? How do I get that missing disk back home again? [Edit] - After adding the md1 to mdadm.conf it now tries to mount the array on startup but it's still missing the disk. If I tell it to try and assemble automatically I get the impression it know it needs sdd but can't use it: root@uberserver:~# mdadm --assemble --scan /dev/md1: File exists mdadm: /dev/md/1 already active, cannot restart it! mdadm: /dev/md/1 needed for /dev/sdd1... What am I missing?

  Read the article

• Slow disk transfer rate

  - by Nooklez

  I have problem with slow disk transfer rate. It's static files server for our website. I was making backup of data and noticed that tar is very slow. So I did hdparm -t and... hdparm -t /dev/sda3 /dev/sda3: Timing buffered disk reads: 6 MB in 4.70 seconds = 1.28 MB/sec It's low traffic hour now on our site, so huge I/O traffic is not a reason (iotop show less than 1 MB/s). It's RAID10 setup (2x2 SATA drives). Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache AVrfy ------------------------------------------------------------------------------ u0 RAID-10 OK - - 64K 1396.96 W ON VPort Status Unit Size Type Phy Encl-Slot Model ------------------------------------------------------------------------------ p0 OK u0 698.63 GB SATA 0 - WDC WD7500AADS-00M2 p1 OK u0 698.63 GB SATA 1 - WDC WD7500AADS-00M2 p2 OK u0 698.63 GB SATA 2 - WDC WD7500AADS-00M2 p3 OK u0 698.63 GB SATA 3 - WDC WD7500AADS-00M2 We have recently changed almost all components of server (excluding 3ware controller + disks). And I think problems started since then. Can it be configuration problem or hardware? EDIT: I found something like that in dmesg [166843.625843] irq 16: nobody cared (try booting with the "irqpoll" option) [166843.625846] Pid: 0, comm: swapper Not tainted 3.1.5-gentoo #3 [166843.625847] Call Trace: [166843.625848] <IRQ> [<ffffffff810859d5>] __report_bad_irq+0x35/0xc1 [166843.625856] [<ffffffff81085cec>] note_interrupt+0x165/0x1e1 [166843.625859] [<ffffffff8108445f>] handle_irq_event_percpu+0x16f/0x187 [166843.625861] [<ffffffff810844a9>] handle_irq_event+0x32/0x51 [166843.625863] [<ffffffff8108640b>] handle_fasteoi_irq+0x75/0x99 [166843.625866] [<ffffffff810039d7>] handle_irq+0x83/0x8b [166843.625868] [<ffffffff810036ad>] do_IRQ+0x48/0xa0 [166843.625871] [<ffffffff8155082b>] common_interrupt+0x6b/0x6b [166843.625872] <EOI> [<ffffffff812981e8>] ? acpi_safe_halt+0x22/0x35 [166843.625877] [<ffffffff812981e2>] ? acpi_safe_halt+0x1c/0x35 [166843.625879] [<ffffffff81298216>] acpi_idle_do_entry+0x1b/0x2b [166843.625881] [<ffffffff81298276>] acpi_idle_enter_c1+0x50/0x99 [166843.625884] [<ffffffff813b792a>] cpuidle_idle_call+0xed/0x171 [166843.625886] [<ffffffff81001257>] cpu_idle+0x55/0x81 [166843.625888] [<ffffffff81532a69>] rest_init+0x6d/0x6f [166843.625891] [<ffffffff81aa1aca>] start_kernel+0x329/0x334 [166843.625893] [<ffffffff81aa12a6>] x86_64_start_reservations+0xb6/0xba [166843.625894] [<ffffffff81aa139c>] x86_64_start_kernel+0xf2/0xf9 [166843.625896] handlers: [166843.625898] [<ffffffff812dc8de>] twl_interrupt [166843.625900] Disabling IRQ #16 It's related to problem? EDIT #2: Based on feedback in comments, here is more informations. cat /proc/interrupts 16: 390813 0 0 0 IO-APIC-fasteoi 3w-sas Controller model: [ 1.095350] 3ware Storage Controller device driver for Linux v1.26.02.003. [ 1.095467] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014. [ 1.095641] LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000. [ 1.095787] 3w-sas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.095881] 3w-sas 0000:01:00.0: setting latency timer to 64 [ 1.910801] 3w-sas: scsi0: Found an LSI 3ware 9750-4i Controller at 0xfe560000, IRQ: 16. [ 2.216537] 3w-sas: scsi0: Firmware FH9X 5.08.00.008, BIOS BE9X 5.07.00.011, Phys: 8. [ 2.216836] scsi 0:0:0:0: Direct-Access LSI 9750-4i DISK 5.08 PQ: 0 ANSI: 5 And motherboard: description: Motherboard product: P8H67-M vendor: ASUSTeK Computer INC.

  Read the article

• Proliant server will not accept new hard disks in RAID 1+0?

  - by Leigh

  I have a HP ProLiant DL380 G5, I have two logical drives configured with RAID. I have one logical drive RAID 1+0 with two 72 gb 10k sas 1 port spare no 376597-001. I had one hard disk fail and ordered a replacement. The configuration utility showed error and would not rebuild the RAID. I presumed a hard disk fault and ordered a replacement again. In the mean time I put the original failed disk back in the server and this started rebuilding. Currently shows ok status however in the log I can see hardware errors. The new disk has come and I again have the same problem of not accepting the hard disk. I have updated the P400 controller with the latest firmware 7.24 , but still no luck. The only difference I can see is the original drive has firmware 0103 (same as the RAID drive) and the new one has HPD2. Any advice would be appreciated. Thanks in advance Logs from server ctrl all show config Smart Array P400 in Slot 1 (sn: PAFGK0P9VWO0UQ) array A (SAS, Unused Space: 0 MB) logicaldrive 1 (68.5 GB, RAID 1, Interim Recovery Mode) physicaldrive 2I:1:1 (port 2I:box 1:bay 1, SAS, 73.5 GB, OK) physicaldrive 2I:1:2 (port 2I:box 1:bay 2, SAS, 72 GB, Failed array B (SAS, Unused Space: 0 MB) logicaldrive 2 (558.7 GB, RAID 5, OK) physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS, 300 GB, OK) physicaldrive 2I:1:3 (port 2I:box 1:bay 3, SAS, 300 GB, OK) physicaldrive 2I:1:4 (port 2I:box 1:bay 4, SAS, 300 GB, OK) ctrl all show config detail Smart Array P400 in Slot 1 Bus Interface: PCI Slot: 1 Serial Number: PAFGK0P9VWO0UQ Cache Serial Number: PA82C0J9VWL8I7 RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: E Firmware Version: 7.24 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Status Details: A cache error was detected. Run more information. Cache Ratio: 100% Read / 0% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Battery/Capacitor Count: 0 SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 0 MB Status: Failed Physical Drive Array Type: Data One of the drives on this array have failed or has Logical Drive: 1 Size: 68.5 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 17594 Strip Size: 128 KB Full Stripe Size: 128 KB Status: Interim Recovery Mode Caching: Enabled Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive0 Mount Points: C:\ 68.5 GB Logical Drive Label: A0100539PAFGK0P9VWO0UQ0E93 Mirror Group 0: physicaldrive 2I:1:2 (port 2I:box 1:bay 2, S Mirror Group 1: physicaldrive 2I:1:1 (port 2I:box 1:bay 1, S Drive Type: Data physicaldrive 2I:1:1 Port: 2I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 73.5 GB Rotational Speed: 10000 Firmware Revision: 0103 Serial Number: B379P8C006RK Model: HP DG072A9B7 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:2 Port: 2I Box: 1 Bay: 2 Status: Failed Drive Type: Data Drive Interface Type: SAS Size: 72 GB Rotational Speed: 15000 Firmware Revision: HPD9 Serial Number: D5A1PCA04SL01244 Model: HP EH0072FARUA PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data Logical Drive: 2 Size: 558.7 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Co Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive1 Mount Points: E:\ 558.7 GB Logical Drive Label: AF14FD12PAFGK0P9VWO0UQD007 Drive Type: Data physicaldrive 1I:1:5 Port: 1I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE07QH300009923X1X3 Model: HP DG0300BALVP Current Temperature (C): 32 Maximum Temperature (C): 45 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:3 Port: 2I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE0AHVH00009924P8F3 Model: HP DG0300BALVP Current Temperature (C): 34 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:4 Port: 2I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE08NAK00009924KWD6 Model: HP DG0300BALVP Current Temperature (C): 35 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown

  Read the article

• Linux (or Anaconda) installation, RAID 5

  - by user48058

  I having trouble with installation of Fedora and/or Centos. On first steps of installation, on step What type of devices will your installation involve, whatever I choose, same thing happen: I get window with message An unhandled exception has occurred. This is most likely a bug. Please save a copy of the detailed exception and file a bug report. In Details window there are lots of messages. At the end there are: ERR kernel:[ 81.854179] device-mapper: table: 253:1: raid45: unknown target type WARNING kernel:[ 81.854183] device-mapper: ioctl: error adding target to table Same thing occur with several versions of Fedora (17 and 16, x64, live, etc) and with Centos distribution also. Can you please give me some advices how to avoid this messages? Thank you in advance!

  Read the article

• Linux software raid robustness

  - by Waxhead

  I have a 4 disk 5TB raid5 setup where a disk is showing signs of going down the drain. It is reporting media errors and from dmesg I can see that several read errors are corrected. smartctl does report "notifications" but no panic so far. Since new disks are rather expensive at the moment I am starting to pondering exactly how robust the linux md layer is. I would appreciate if someone could shed some light on how md actually deals with disk errors. For example how does md deal with write and read errors - what does it (really) take for disk to be rejected from an array. I also read that recently md got support for mapping out bad blocks. Does this mean that the read errors I've had would have been mapped out if I where running kernel 3.1 or would md still try to "work on them" to make them usable.

  Read the article

• How to remove raid 5 array of 5 SAS and use only use one SAS at a time without writing any thing to disc for recovery

  - by murtaza hamid

  I have HP server ML370 g5 with 8 SAS, c drive 1 72 gb raid 0, d drive 2 72 gb raid 0, f drive 5 146 gb raid 5. 2 of 5 sas drive has got bad sectors and raid 5 is showing status failed. now i want to remove all this 5 SAS and put 1 by 1 in any of the bay to make its image for data recovery purpose without writing anything to the drive. how should i proceed. i also want to keep drive c and d intact. also is it possible if i put all this 5 drives in the bay with the same sequense will it recognise the raid 5 array ( i read some where its smart controller..just curious) many thanks in advance.

  Read the article

• Replacement Alternative for Dell FY606 in a Poweredge T105

  - by Mike C

  I have recently upgraded my Poweredge T105 server to use a SAS 6/ir RAID controller. Unfortunately, I did not realize at the time that adding the card would cause the BIOS to complain about a missing hard drive fan. This warning requires that a user press F1 to continue, which is disastrous in a server environment. I have searched all over found that the specific part I need is a Dell FY606 fan. However, I have yet to find a suitable retailer that covers this part. I have contacted Dell and they do not have this part in stock. Are there any alternative models of a fan that I could use in place of an FY606? Seems like a pretty straightforward part, just a fan that connects to a 4-pin power connector on the motherboard.

  Read the article

• Raid 11 : how to stop @ how to release devices

  - by santhosha

  #cat /proc/mdstat md7 : active raid10 sdh1[2] 286743936 blocks 64K chunks 2 near-copies [4/1] [__U_] [0:0:3:0] #mdadm -f /dev/md7 /dev/sdh1 mdadm: set /dev/sdh1 faulty in /dev/md7 #mdadm -r /dev/md7 /dev/sdh1 mdadm: hot remove failed for /dev/sdh1: Device or resource busy # umount /dev/md7 umount: /dev/md7: not mounted #mdadm --stop /dev/md7 mdadm: fail to stop array /dev/md7: Device or resource busy #cat /proc/mdstat md7 : active raid10 sdh1[2] 286743936 blocks 64K chunks 2 near-copies [4/1] [__U_] [0:0:3:0]

  Read the article

• Raid HDD Boot up

  - by user234695

  My server is Power Edge 1950 running server 2008 32Bit, using 3 Physical SAS HDD as a Virtual 2 Disk configured for RAID5, with partition of C drive as OS and D drive as Data. Planning to format and install Server 2008 R2 64Bit so I insert a New Physical disk and configured as RAID5 and clone the C drive and D drive to the new hard disk. Now I need to test that the new hard disk is able to boot windows and work as expected. How do I test, I am not able to boot the windows by choosing the new harddisk, the bios show only the existing HDD, not the new one. Also, if I remove the old three hard disk, and leave the new harddisk and then am I able to boot the device, if I do this does my existing RAID5 configuration and data on the hard disk still remain.

  Read the article

• IBM x260m won't boot from PCI raid card

  - by syrenity

  Hi. We ghosted our old Windows 2003 drive to a new 1TB one, and connected through new PCI SATA card. The server fails to boot with error 1962: Boot sector not found. When we connect the drive directly to motherboard, it boots fine, so the problem is probably in getting BIOS boot from the SATA card. Does anyone know how to do it? Thanks.

  Read the article

• HW RAID 1 different disk sizes?

  - by jacka

  I was told by an HP support guy that I should not replace a failed drive in a mirror with a bigger size drive, since it could crash my array. I am puzzled why is this so and how to hell am I suppose to support this array once the specific hdd model is not available any more?

  Read the article

• Can one build a single disk RAID 1 array?

  - by Core Xii

  I have an Nvidia hardware RAID 1 array and need to reformat. But I don't have any spare storage media, so I need to get along with the 2 disks in the array. I figured I'd do as follows: Delete the array, so I have 2 separate but identical disks, A and B, with my files Put disk B aside Reformat disk A, build RAID 1 array with it, install Windows XP Put disk B back in Boot to Windows on disk A, copy my files from disk B to disk A Add disk B to the RAID 1 array, rebuild array And now I'd have a new RAID 1 array, fresh install and all my files intact (the ones I copied). Here are the parts I'm unsure about: Can I build a RAID 1 array using just one disk, then add the other one later? Can Windows on disk A see disk B and allow me to copy my files over?

  Read the article

• mdadm software RAID doesn't load at boot

  - by martinald

  Hi there, I'm using mdadm to create a raid1 mirror across two disks. I can create my /dev/md5 array perfectly using the tools, but it does not automatically reload my /dev/md5 when I restart, I need to manually recreate the array. Am I missing something obvious here?

  Read the article

• Allignment of ext3 partition on LVM RAID volume group

  - by John P

  I'm trying to add a partition on a LVM that resides on a RAID6 volume group and fdisk is complaining about the partition not residing on a physical sector boundry. My question is, how do you calculate the correct starting sector for a partition on a LVM? This partition will be formated ext3. Would it be better to just format the LVM directly instead of creating a new partition? Disk /dev/dedvol/backup: 2199.0 GB, 2199023255552 bytes 255 heads, 63 sectors/track, 267349 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 1048576 bytes / 8388608 bytes Disk identifier: 0x4e428f49 Device Boot Start End Blocks Id System /dev/dedvol/backup1 63 267349 2146982827+ 83 Linux Partition 1 does not start on physical sector boundary. lvdisplay /dev/dedvol/backup --- Logical volume --- LV Name /dev/dedvol/backup VG Name dedvol LV UUID OV2n5j-7LHb-exJL-t8dI-dU8A-2vxf-uIicCt LV Write Access read/write LV Status available # open 0 LV Size 2.00 TiB Current LE 524288 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 32768 Block device 253:1 vgdisplay dedvol --- Volume group --- VG Name dedvol System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 3 VG Access read/write VG Status resizable MAX LV 0 Cur LV 2 Open LV 1 Max PV 0 Cur PV 1 Act PV 1 VG Size 14.55 TiB PE Size 4.00 MiB Total PE 3815448 Alloc PE / Size 3670016 / 14.00 TiB Free PE / Size 145432 / 568.09 GiB VG UUID 8fBcOk-aXGx-P3Qy-VVpJ-0zK1-fQgy-Cb691J

  Read the article

• Sort-of Software Raid-1 on windows?

  - by ricardowong

  I have 2 windows vista computers on a lan, can i set them up with a program so that they replicate the data written in one partition to another and the other way around. basically replicating data across 2 partitions whenever each is modified. Making that data is available on the network when either of the computers are turned on, when both are, data is synchronized. Is this posible?

  Read the article

• Software RAID for several HDs which retains files on each HD

  - by Fuxi

  Is there some kind of software/driver that would enable me to create one big volume out of several hard disks but retain the file structure on each HD? This would be in case where one hard disk crashes and only data on that HD will be lost. Windows 7 enables me to do that but in case one HD breaks all data will be lost.

  Read the article

• MDADM RAID5 array showing as CLEAN FAULTY

  - by Dean Reilly

  A drive dropped out of my raid 5 array yesterday. It looks like the reason was due to a bad controller so I switched it out and attempted to re-add the drive but mdadm claimed it couldn't do it. So I zerod the superblock and just added the drive normally and left it to resync. When I came to check on the array this morning I was unable to mount it at all and it's now showing as CLEAN FAULTY with two drives missing. The two missing drives are listed as spare and faulty spare. Is there anything I can do in this situation or is the array gone?

  Read the article

• What RAID level for a backup server?

  - by ispirto

  I'm building a server with 12 x 3TB disks to use daily backups. I'm thinking to use RAID50 to get a good 27TB usable space. The disks will be used brutally to backup 9 servers with 1.5TB of data once a day. I'll keep the backups for 2 days. So for each server I'll have 3TB of separate partitions. Do you think this kind of huge backups would stress the disks too much and make them fail? Should I better go with RAID10? Oktay

  Read the article

• Will my RAID0 stay intact when I move it to a new computer?

  - by Jeremy H

  My primary drive is a 250GB WD SATA drive. So, I added 2x 500GB 7,200 RPM WD SATA drives into my Windows Vista box and created a 1TB RAID0. I then formatted the the primary drive and installed Windows 7. To my pleasant surprise when I booted into Windows 7 my RAID0 was still intact and I kept trotting along the same as I did before. Now I am replacing my motherboard, processor, and RAM and plan on formatting the primary 250GB drive again and using it to boot for a new clean install of Windows 7. My question is: if I move these two SATA drives which are setup for RAID0 into the new system, install Windows 7 again, will the RAID0 remain? Edit: Software RAID. I created it within Windows. The RAID0 does NOT contain the system boot partition.

  Read the article

• INtel SSD RAID Trim

  - by Mike Pateras

  I just found this article, that says that Intel now supports Trim for SSD RAIDs. It links to this download page. I'm pretty excited about that, but I'm a little confused. There seem to be two sets of drivers, an executable and something that's bootable. I ran the executable. Is that just to apply the drivers to my system now, and are the bootable drivers so that if I re-format, I won't have to re-run everything? Do I need to do both? And is there a way to check if it worked? I'm running an i7 in Windows 7 (ASUS P6T Deluxe Motherboard), if that's significant.

  Read the article

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >