Search Results

Search found 12267 results on 491 pages for 'out of memory'.

Page 200/491 | < Previous Page | 196 197 198 199 200 201 202 203 204 205 206 207  | Next Page >

  • Why my laptop doesnt boot in any OS (windows or ubuntu) after RAM upgrade?

    - by qrsq
    My laptop previously had 2 slots of RAM ( 1x1Gb , 1x2GB , both were clocked at 1066mhz) and it was working on windows 7 x86 OS. I Upgraded the ram with ( 2x4GB clcoked at 1333mhz). Bios displayed 8192MB of memory and windows was working ok but (only 2.99GB of ram from 8gb was avabile). So i decided to switch to an x64 system to be able to use all the amount of memory. But the laptop wasnt able to install any os (windows 7 x64 or windows 8 x64) so i placed the 3gb of ram instead of 8gb. Then i succesfully instaled an x64 os (windows 8). After than i placed the 8gb ram back again. Now the computer doesnt boot in the os but bios is working normally. I tried also to install ubuntu , without any succes. What should i do ?? All the help will be appreciated. thanks

    Read the article

  • Is the motherboard the cause of these errors?

    - by ianfuture
    Motherboard is : ASUS A7N8X-E Deluxe, Rev1.01, On start up get: "cmos checksum error - defaults loaded" error BIOS is reset everytime and can't boot to Windows off HDD. POST report is ok once I tell it there is no Floppy drive attached and not to seek it. The boot sequence starts then just as get to load windows safe mode options whole PC shuts down. BIOS is reset to defaults again. I've checked the battery and jumpers. Tried a known working battery. Changed Graphics card, changed memory, changed HD to one without an OS. Disconnected DVD drive. PSU is known to be ok. IN BIOS CPU is recognised correctly and memory is also recognised ok. So is it likely to be a bad motherboard or corrupted BIOS or something else? Thanks :)

    Read the article

  • Snapshot/rollback for libvirt+KVM?

    - by jtimberman
    I've recently begun using KVM for my development/test environment on a Linux host system with 8G memory. Prior, I was using VMware Fusion for my virtual environment, but my Macbook only has 2G memory. I tried VMware Server and ESX on the host instead of KVM, but the webUI doesn't run on Mac OSX's Firefox, and we're going to be doing more with KVM anyway. The main feature of VMware I miss is robust snapshot/rollback, but I'm missing this in KVM. I understand the snapshot command, but it shuts down the guest OS when complete, and then copying the disk image to preserve its state is cumbersome. Is this really the best way to manage snapshots on KVM?

    Read the article

  • Unable to create context rendering error whet run OpenGL application

    - by Rodnower
    Hello, I try to run Mesa gears example and I get following error: freeglut (./gears): Unable to create direct context rendering for window 'Gears' This may hurt performance. though the application runs successfully, but I guess that in future I will have much problems with productivity. I run Linux CentOS 5 on WMvare 7. Mesa's version is 6.5 Relevant output of lspci -v gives: 00:0f.0 VGA compatible controller: VMware SVGA II Adapter (prog-if 00 [VGA controller]) Subsystem: VMware SVGA II Adapter Flags: bus master, medium devsel, latency 64, IRQ 9 I/O ports at 10d0 [size=16] Memory at d0000000 (32-bit, non-prefetchable) [size=128M] Memory at d8000000 (32-bit, non-prefetchable) [size=8M] [virtual] Expansion ROM at 30000000 [disabled] [size=32K] Capabilities: [40] Vendor Specific Information Any one have idea? There is driver of vmvare for CentOS? Thank you for ahead.

    Read the article

  • backing up a virtual machine

    - by ErocM
    I inquired with the support of justcloud.com telling them that I have a vmware vm that I was wondering if it could be backed up while in use. I can back up the vm once it is shut down but I was wondering if their "shadow copy" would back it up while running. This was their response: Thank you for your email. I am really very sorry but virtual machines can't be backed up for a simple reason that they are virtual, they have virtual memory, not physical memory. Please let me know if there is anything else I can help with. Kind Regards, Barry James User Experience Team www.justcloud.com These are physical files so I wasn't sure I even understood the response. Am I wrong in thinking that a vm can be backed up while in use? Does this response even make sense? I need a cheap alternative to backing up the vm off the server in case it goes down. Any suggestions?

    Read the article

  • Download - Upload is too slow on Centos

    - by Mehdi
    My download/upload in server and out of server is too slow (around 50 KB/s !) ! Did I miss some configuration ? Some information: CentOS release 6.3 uptime load average: 0.17, 0.32, 0.37 Memory free -m total used free shared buffers cached Mem: 24009 21988 2021 0 806 18098 -/+ buffers/cache: 3083 20926 Swap: 4095 28 4067 lshw -C network *-network description: Ethernet interface product: 82574L Gigabit Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 00 serial: 00:25:90:70:17:4a size: 100MB/s capacity: 1GB/s width: 32 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=off broadcast=yes driver=e1000e driverversion=1.9.5-k duplex=full firmware=2.1-2 ip=108.175.8.123 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:16 memory:fb900000-fb91ffff ioport:e000(size=32) memory:fb920000-fb923fff ethtool ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off MDI-X: off Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000001 (1) Link detected: yes dmesg |grep e1000e dmesg |grep e1000e e1000e: Intel(R) PRO/1000 Network Driver - 1.9.5-k e1000e: Copyright(c) 1999 - 2012 Intel Corporation. e1000e 0000:02:00.0: Disabling ASPM L0s e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 e1000e 0000:02:00.0: setting latency timer to 64 e1000e 0000:02:00.0: irq 33 for MSI/MSI-X e1000e 0000:02:00.0: irq 34 for MSI/MSI-X e1000e 0000:02:00.0: irq 35 for MSI/MSI-X e1000e 0000:02:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:70:17:4a e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: Unsupported Speed/Duplex configuration e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: Disabling ASPM L1 e1000e 0000:02:00.0: eth0: changing MTU from 1500 to 9000 e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO

    Read the article

  • Dumping a Linux console scrollback buffer?

    - by Gerald Combs
    We would like to save the output of a program run on a Linux console which spans many lines. Unfortunately it wasn't logged or run under screen, or any other way that lets us easily capture the output. The best method we've been able to come up with so far is: Log into the machine via a separate SSH session In the console session, page to the top of the buffer Repeat: In the SSH session, run "cat /dev/vcs >> screendump.txt" In the console session, page down one screen Dump the final screen in the SSH session Is there a better way? It seems like if the VC memory were contiguous and you knew where it was you could use dd to pull the console text directly out of kernel memory and into a file.

    Read the article

  • Shared SQL Server 2008

    - by nazaf
    Hi, I have a Windows Hyper VPS plan with 1024 MB of RAM. After installing SQL Server 2008 Express, my memory usage went up to 75% without running my site yet. I know that SQL Server consumes a lot of memory, so I decided to host my DB on a shared server. Which of the following is more scalable: install my DB on my VPS, or on a shared server ? If the latter, then can you recommend me a good shared server? Thanks.

    Read the article

  • Server 2008 Hard Faults

    - by claw
    Hey all, plase bear with me as I haven't looked at a server in a very long time. The problem I am having is with a Windows 2008 Standard FE Service Pack 2 Intel Xeon X3430 @ 2.40 2.39 GHZ 4 GB Memory 64 Bit There seems to be no problems other than the physical memory peaking at 91%, always with over 100 Hard Faults Per Second. To my understanding hard faults should be fairly rare on a machine with. Are there any logs I can show you? Or investigate myself. The general performance of the machine is ok, i can access SBS2008 and change settings fairly smoothly without hangs etc. However, we connect to the server and do quite a bit of SQL via an application. For a record to retrieve say 20 rows, it can take 20+ seconds. Thanks in advance, Jamie EDIT: What the server is used for: IIS ASP Web Service SQL 2008 List item Exchange unable to upload screenshots due to low reputation - why doesnt my SO work here :)

    Read the article

  • Forgotten laptop windows login - what are my options?s

    - by Galwegian
    I have a (elderly) colleague who has forgotten the password to his laptop - he generally signs in as Administrator, but can't remember the password, and has asked my help. He says the laptop contains some important data. What are my options? Thanks for any help. EDIT: I have just got hold of the machine and not all is as I was told... The password is not the problem... Before the login box appears I get an error message relating to savedump.exe: The instruction at "0x0..." referenced memory at "0x0...". The memory could not be written. Then when I login using the proper credentials, It logs me in for a tiny second and then logs me out again and 'saves my settings'. Any ideas on this one?

    Read the article

  • Access Monit on PHP

    - by xian
    i have a remote server (Centos 5.8) and i have installed monit on it as my monitoring tool. monit installation yum install monit now, on my local machine (still Centos5.8), i want to get the system status (shown below) of the said server provided by monit --------------------------------------------------- | Parameter | Value | --------------------------------------------------- | Name | serverHostname | | Status | Running | | Monitoring mode | active | | Monitoring status | Monitored | | Data collected | Fri, 22 Jun 2012 16:47:01 | | Load average | [0.32] [0.37] [0.43] | | CPU usage | 3.3%us 0.2%sy 0.0%wa | | Memory usage | 2005212 kB [53.9%] | | Swap usage | 893256 kB [21.8%] | --------------------------------------------------- This information is shown when you clicked on the system name link found on the your monit's home page http://localhost:2812 How can I do that in php? How can I retrieve those information? i was thinking of executing this linux command in php: /usr/bin/monit status Output of this is The Monit daemon 5.4 uptime: 2h 55m System 'system_asi454' status Running monitoring status Monitored load average [0.22] [0.34] [0.42] cpu 3.3%us 0.2%sy 0.0%wa memory usage 2005212 kB [53.9%] swap usage 892928 kB [21.8%] data collected Fri, 22 Jun 2012 16:47:01 which is similar to the table content show above.

    Read the article

  • What options can I use in totem, xine or vlc to play on machines with limited resources?

    - by Nina
    Mplayer has some options that allow me to play it on a machine with limited resources. I can use mplayer -vo x11 -zoom -framedrop to play videos when otherwise I'd run out of memory. At least I think I'm running out of memory. I am running our of some resource for sure. -vo sets the video output driver -zoom actually I don't know what this does, but it works for me ;-) -framedrop allows mplayer to not render frames if it falls behind. Are there similar command line controls (or a defaults file) for totem, vlc or xine?

    Read the article

  • What kind of server hardware is roughly necessary to serve website to 10k users?

    - by jcmoney
    I've been looking at VPS's and the specs they offer for entry level setups seems somewhat surprising to me. I'm am new to this topic but many of VPS offer less than 512MB of memory and my laptop has 4GB of memory so I am curious what does it actually take in terms of hardware to serve say 10k users (say 5k daily active users)? I figure a large number of factors can probably sway this a lot but just for benchmarking, say the site is a social networking site written in php using mysql + apache that's not really doing anything unusual like serving lots of media. So essentially a very basic Facebook minus the absurd number of photos and videos. What about 100k users (50k daily active)? 1 million (500k daily active)? Thanks in advance.

    Read the article

  • Hardware upgrade: Windows 7 bluescreens, Vista loads

    - by Daniel Schaffer
    I just did a fairly significant hardware upgrade while keeping my hard disks. The old system was a dell Optiplex 745 with an Intel Core 2 duo, LGA 775. The new system is custom built, Intel i5 750. I know you're supposed to do a clean install with a hardware upgrade like this, but I'd had success in the past doing the stealth hardware upgrade like this, so I figured I'd give it a shot. Windows 7 Ultimate 64 bit gets through the loading screen and immediately blue screens and reboots. Windows Vista Home Premium 32-bit, which I have on an old hard drive from an AMD box (!!) loads up fine. I ran through the windows memory checker just to be sure, and my memory is fine. So, is the BSOD the result of some sort of protection mechanism specific to Windows 7? Is there any hope of salvaging that install?

    Read the article

  • How to find which tab a particular Chrome process refers to

    - by George
    I often have 6 or 7 separate Chrome windows open, often with 5-10 tabs in each. When I look at Windows Task Manager, I see each chrome.exe process, with some using a large amount of memory. How can I find which particular tab the process refers to? I want to know which one uses the most memory and close that tab instead of having to close every Chrome window. Is there any way to get this information? This is on Windows Vista, but it is the same on other versions of Windows as well.

    Read the article

  • how to optimize virtual box shared folders

    - by Nrew
    This is really pissing me off. No matter how much memory I put into the guest os(windows xp). It still hangs for about 365 days before you can access the file you want to access from the shared folder. What do I do to make things faster? Because after it hangs and not respond for 365 days. It will do it again for another 250 days. Ive even set the shared folder to permanent. This is a fairly decent machine: 2.50ghz processor(x64 architecture, but I have only 2Gb of memory so my host os is just 32 bit windows 7) hdd has much space left: 156 Gb free of 250Gb

    Read the article

  • Another installation is in progress

    - by Steven
    Why I try to install any program I see "Another installation is in progress. You must complete that installation before continuing this one." error. Googled the web and found that solution would be to delete HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Installer\InProgress registry key and reboot. That didn't help me unfortunately. When I open "Services" mmc snapin it shows that "Windows Installer" service is "Started", but "Start/Stop/Pause/Restart" buttons are grayed (the interesting thing is that startup type = "Manual", so I don't really know how to explain that I already have 2 instances of msiexec.exe in memory and one instance is consuming 50Mb of memory. Looks like there's a serious issue with my installer service - is there any way to fix it (please do mind - I can't install anything!) Any help would be greatly appreciated.

    Read the article

  • Need deleted data back from Pen Drive, Please help

    - by Manav Sharma
    All, I am using a Pendrive to transfer files from one system to another. I think I deleted some files from the Pendrive that I now need back. Also, there are chances that I might have overwritten the memory where the deleted data might have existed. Is there any software to do something about that? I understand that logically whatever is overwritten in memory cannot to fetched back. But still I need to trust the advances in the technology. Any help is appreciated. Thanks

    Read the article

  • IIS/ASP.NET performance incident - Perfmon Current Annonymous Users going through roof but Requests/sec low

    - by Laurence
    Setup: ASP.NET 4.0 website on IIS 6.0 on Win 2003 64 bit, 8xCPUs, 16GB memory, separate SQL 2005 DB server. Had a serious slowdown today with any otherwise fairly well performing ASP.NET site. For a period of a couple of hours all page requests were taking a very long time to be served - e.g. 30-60s compared to usual 2s. The w3wp.exe's CPU and memory usage on the webserver was not much higher than normal. The application pool was not in the middle of recycling (and it hadn't recycled for several hours). Bottlenecks in the database were ruled out - no blocks occurring and query results were being returned quickly. I couldn't make any sense of it and set up the following Perfmon counters: Current Anonymous Users (for site in question) Get requests/sec (ditto) Requests/sec for the ASP.NET application running the site Get requests/sec was averaging 100-150. Requests/sec for ASP.NET was averaging 5-10. However Current Anonymous Users was around 200. And then as I was watching, the Current Anonymous Users began to climb steeply going up to about 500 within a few minutes. All this time Get requests/sec & Requests/sec for ASP.NET was if anything going down. I did a whole load of things (in a panic!) to try to get the site working, like shutting it down, recycling the app pool, and adding another worker process to the pool. I also extended the expiration time for content (in IIS under HTTP Headers) in an attempt to lower the number of requests for static files (there are a lot of images on the site). The site is now back to normal, and the counters are fairly steady and reading (added Current Connections counter): Current Anonymous Users : average 30 Get requests/sec : average 100 Requests/sec for ASP.NET : 5 Current Connections : average 300 I have also observed an inverse relationship between Get requests/sec & Current Anonymous Users. Usually both are fairly steady but there will be short periods when Get requests/sec will go down dramatically and Current Anonymous Users will go up in a perfect mirror image. Then they will flip back to their usual levels. So, my questions are: Thinking of the original performance issue - if w3wp.exe CPU, memory usage were normal and there was no DB bottleneck, what could explain page requests taking 20 times longer to be served than usual? What other counters should I be looking at if this happens again? What explains the inverse relationship between Get requests/sec & Current Anonymous Users? What could explain Current Anonymous Users going from 200 to 500 within a few minutes? Many thanks for any insight into this.

    Read the article

  • Why MySQL sat for 2 minutes doing nothing?

    - by Alex R
    This was a one-time thing, not reproducible... But I saved the show innodb status output. Can anybody tell what's going on here? The simple insert took almost 3 minutes to complete. | InnoDB | | ===================================== 110201 15:58:10 INNODB MONITOR OUTPUT ===================================== Per second averages calculated from the last 34 seconds ---------- SEMAPHORES ---------- OS WAIT ARRAY INFO: reservation count 11963, signal count 11766 --Thread 1824 has waited at .\btr\btr0cur.c line 443 for 118.00 seconds the sema phore: S-lock on RW-latch at 09D6453C created in file .\buf\buf0buf.c line 550 a writer (thread id 1824) has reserved it in mode wait exclusive number of readers 1, waiters flag 1 Last time read locked in file .\buf\buf0flu.c line 599 Last time write locked in file .\btr\btr0cur.c line 443 Mutex spin waits 0, rounds 527817, OS waits 7133 RW-shared spins 2532, OS waits 1226; RW-excl spins 1652, OS waits 1118 ------------ TRANSACTIONS ------------ Trx id counter 0 95830 Purge done for trx's n:o < 0 95814 undo n:o < 0 0 History list length 11 LIST OF TRANSACTIONS FOR EACH SESSION: ---TRANSACTION 0 0, not started, OS thread id 3704 MySQL thread id 551, query id 2702112 localhost 127.0.0.1 root show innodb status ---TRANSACTION 0 95829, not started, OS thread id 3132 MySQL thread id 534, query id 2702020 localhost 127.0.0.1 root ---TRANSACTION 0 95828, not started, OS thread id 3152 MySQL thread id 527, query id 2701973 localhost 127.0.0.1 root ---TRANSACTION 0 95827, ACTIVE 118 sec, OS thread id 1824 inserting, thread decl ared inside InnoDB 500 mysql tables in use 1, locked 1 1 lock struct(s), heap size 320, 0 row lock(s) MySQL thread id 526, query id 2701972 localhost 127.0.0.1 root update INSERT INTO log_searchcriteria (userid,search_criteria,date,search_type) VALUES ( NAME_CONST('userid',NULL), NAME_CONST('search_criteria',_latin1' SELECT SQL_C ALC_FOUND_ROWS idx_search.CTCX_LATITUDE, idx_search.CTCX_LONGITUDE, idx_search.b uilding_id, idx_search.LN_LIST_NUMBER, idx_search.LP_LIST_PRICE, idx_search.HSN_ ADRESS_HOUSE_NUMBER, idx_search.STR_ADDRESS_STREET, idx_search.CP_ADDRESS_COMPAS S_POINT, idx_search.UN_UNIT, idx_search.CIT_CITY, idx_search.ZP_ZIP_CODE, idx_se arch.AR_AREA_NAME, idx_search.BR_BEDROOMS, idx_search.BTH_BATHS, idx_search.ST_S TATUS, idx_search.CTCX_STYLE_TYPE, idx_s -------- FILE I/O -------- I/O thread 0 state: wait Windows aio (insert buffer thread) I/O thread 1 state: wait Windows aio (log thread) I/O thread 2 state: wait Windows aio (read thread) I/O thread 3 state: wait Windows aio (write thread) Pending normal aio reads: 0, aio writes: 1, ibuf aio reads: 0, log i/o's: 0, sync i/o's: 0 Pending flushes (fsync) log: 0; buffer pool: 0 151006 OS file reads, 120758 OS file writes, 6844 OS fsyncs 0.00 reads/s, 0 avg bytes/read, 0.00 writes/s, 0.00 fsyncs/s ------------------------------------- INSERT BUFFER AND ADAPTIVE HASH INDEX ------------------------------------- Ibuf: size 1, free list len 5, seg size 7, 24664 inserts, 24664 merged recs, 4612 merges Hash table size 553253, node heap has 629 buffer(s) 0.00 hash searches/s, 0.00 non-hash searches/s --- LOG --- Log sequence number 5 2318193115 Log flushed up to 5 2318193115 Last checkpoint at 5 2318129891 0 pending log writes, 0 pending chkp writes 3036 log i/o's done, 0.00 log i/o's/second ---------------------- BUFFER POOL AND MEMORY ---------------------- Total memory allocated 213459462; in additional pool allocated 1720192 Dictionary memory allocated 240416 Buffer pool size 8192 Free buffers 0 Database pages 7563 Modified db pages 18 Pending reads 0 Pending writes: LRU 0, flush list 18, single page 0 Pages read 150973, created 28788, written 115137 0.00 reads/s, 0.00 creates/s, 0.00 writes/s No buffer pool page gets since the last printout -------------- ROW OPERATIONS -------------- 1 queries inside InnoDB, 0 queries in queue 1 read views open inside InnoDB Main thread id 2992, state: flushing buffer pool pages Number of rows inserted 794294, updated 89203, deleted 13698, read 1453084305 0.00 inserts/s, 0.00 updates/s, 0.00 deletes/s, 0.00 reads/s ---------------------------- END OF INNODB MONITOR OUTPUT ============================ Thanks

    Read the article

  • Lightest Linux Desktop supporting Firefox/graphic browser

    - by Susan Mayer
    I am on Windows and I have a remote server with Ubuntu 10.10. I want to use Firefox or other graphic browser on that remote server. The problem is, the server's memory is only 512MB, so I can install larger desktop environment. I used to use XFCE and NoMachine NX, but they consume too much memory on that Ubuntu server. The only thing I want to use is a graphic browser (for example firefox) on that server. Nothing else. Do you have any good suggestions? Thanks a lot!

    Read the article

  • Does shutdown idle VMs improve the performance?

    - by Samselvaprabu
    Often our team members are coming to me with a compliant that their VMs are slow. Our team members suggested to shutdown some of the VMs temporarily and try to access the VM. But most cases that would not help. Assume that i have assigned 4 GB for and 2 CPUs for my VM. So ideally it should not face performance issue. As our ESXi 4.1 server has multiple VM in the same server (we have overcommited memory and CPU). Does shut down other VM really helps to improve performance or not? [Note : We are using ESXi 4.1 and our hardware is R710 server. We have more number of VMs in single server so we have overcommited memory.]

    Read the article

  • Do SSD hybrid drives perform better than HDD + ReadyBoost flash?

    - by Chris W. Rea
    Seagate has released a product called the Momentus XT Solid State Hybrid Drive. This looks exactly like what Windows ReadyBoost attempts to do with software at the OS level: Pairing the benefits of a large hard drive together with the performance of solid-state flash memory. Does the Momentus XT out-perform a similar ad-hoc pairing of a decent hard drive with similar flash memory storage under Windows ReadyBoost? Other than the obvious "a hardware implementation ought to be faster than a software implementation", why would ReadyBoost not be able to perform as well as such a hybrid device?

    Read the article

  • NVRAM for journals on Linux?

    - by symcbean
    I've been thinking about ways of speeding up disk I/O, and one of the bottlenecks I keep coming back to is the journal. There's an obvious benefit to using an SSD for the journal - over and above just write caching unless of course I just disable the journal with the write cache (after all devicemapper doesn't seem to support barriers). In order to get the benefits from using a BB write cache on the controller, then I'd need to disable journalling - but then the OS should try to fsck the system after an outage. Of course if the OS knows what's in the batter-backed memory then it could use it as the journal - but that means it must be exposed as a block device and only be under the control of the operating system. However I've not been able to find a suitable low-cost device (no, write-levelling for Flash is not adequate for a journal, at least one which uses Smartmedia). While there's no end of flash devices, disk/array controllers with BB write caches, so far I've not found anything which just gives me non-volatile memory addressable as a block storage device.

    Read the article

< Previous Page | 196 197 198 199 200 201 202 203 204 205 206 207  | Next Page >