Search Results

Search found 5278 results on 212 pages for 'hitchhikers guide to the galaxy'.

Page 202/212 | < Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209 | Next Page >

How do I configure OpenVPN for accessing the internet with one NIC?

- by Lekensteyn

I've been trying to get OpenVPN to work for three days. After reading many questions, the HOWTO, the FAQ and even parts of a guide to Linux networking, I cannot get my an Internet connection to the Internet. I'm trying to set up a OpenVPN server on a VPS, which will be used for: secure access to the Internet bypassing port restrictions (directadmin/2222 for example) an IPv6 connection (my client does only have IPv4 connectivity, while the VPS has both IPv4 and native IPv6 connectivity) (if possible) I can connect to my server and access the machine (HTTP), but Internet connectivity fails completely. I'm using ping 8.8.8.8 for testing whether my connection works or not. Using tcpdump and iptables -t nat -A POSTROUTING -j LOG, I can confirm that the packets reach my server. If I ping to 8.8.8.8 on the VPS, I get an echo-reply from 8.8.8.8 as expected. When pinging from the client, I do not get an echo-reply. The VPS has only one NIC: etho. It runs on Xen. Summary: I want to have a secure connection between my laptop and the Internet using OpenVPN. If that works, I want to have IPv6 connectivity as well. Network setup and software: Home laptop (eth0: 192.168.2.10) (tap0: 10.8.0.2) | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | router/gateway (gateway 192.168.2.1) | INTERNET | VPS (eth0:1.2.3.4) (gateway, tap0: 10.8.0.1) (running Debian 6; OpenVPN 2.1.3-2) wifi and my home router should not cause problems since all traffic goes encrypted over UDP port 1194. I've turned IP forwarding on: # echo 1 > /proc/sys/net/ipv4/ip_forward iptables has been configured to allow forwarding traffic as well: iptables -F FORWARD iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT iptables -A FORWARD -j DROP I've tried each of these rules separately without luck (flushing the chains before executing): iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j SNAT --to 1.2.3.4 iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE route -n before (server): 1.2.3.4 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 1.2.3.4 0.0.0.0 UG 0 0 0 eth0 route -n after (server): 1.2.3.4 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 0.0.0.0 1.2.3.4 0.0.0.0 UG 0 0 0 eth0 route -n before (client): 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 route -n after (client): 1.2.3.4 192.168.2.1 255.255.255.255 UGH 0 0 0 wlan0 10.8.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 0.0.0.0 10.8.0.1 128.0.0.0 UG 0 0 0 tap0 128.0.0.0 10.8.0.1 128.0.0.0 UG 0 0 0 tap0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 SERVER config proto udp dev tap ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" ifconfig-pool-persist ipp.txt keepalive 10 120 tls-auth ta.key 0 comp-lzo user nobody group nobody persist-key persist-tun log-append openvpn-log verb 3 mute 10 CLIENT config dev tap proto udp remote 1.2.3.4 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 mute 20 traceroute 8.8.8.8 works as expected (similar output without OpenVPN activated): 1 10.8.0.1 (10.8.0.1) 24.276 ms 26.891 ms 29.454 ms 2 gw03.sbp.directvps.nl (178.21.112.1) 31.161 ms 31.890 ms 34.458 ms 3 ge0-v0652.cr0.nik-ams.nl.as8312.net (195.210.57.105) 35.353 ms 36.874 ms 38.403 ms 4 ge0-v3900.cr0.nik-ams.nl.as8312.net (195.210.57.53) 41.311 ms 41.561 ms 43.006 ms 5 * * * 6 209.85.248.88 (209.85.248.88) 147.061 ms 36.931 ms 28.063 ms 7 216.239.49.36 (216.239.49.36) 31.109 ms 33.292 ms 216.239.49.28 (216.239.49.28) 64.723 ms 8 209.85.255.130 (209.85.255.130) 49.350 ms 209.85.255.126 (209.85.255.126) 49.619 ms 209.85.255.122 (209.85.255.122) 52.416 ms 9 google-public-dns-a.google.com (8.8.8.8) 41.266 ms 44.054 ms 44.730 ms If you have any suggestions, please comment or answer. Thanks in advance.

Read the article
UnmarshalException: unexpected element

- by Tom Brito

I'm working with JAXB, and I'm having trouble to unmarshall a file; The following lines, on the beginning of the file, are causing trouble: <!DOCTYPE package PUBLIC "+//ISBN 0-9673008-1-9//DTD OEB 1.2 Package//EN" "http://openebook.org/dtds/oeb-1.2/oebpkg12.dtd"> <package xmlns="http://openebook.org/namespaces/oeb-package/1.0/" unique-identifier="uid"> If I delete all the !DOCTYPE it gives no Exception, but it doesn't load any value either. The program (with the !DOCKTYPE) is throwing the exeption: javax.xml.bind.UnmarshalException: unexpected element (uri:"http://openebook.org/namespaces/oeb-package/1.0/", local:"package"). Expected elements are <{}dc-metadata>,<{}dc:Contributor>,<{}dc:Coverage>,<{}dc:Creator>,<{}dc:Date>,<{}dc:Description>,<{}dc:Format>,<{}dc:Identifier>,<{}dc:Language>,<{}dc:Publisher>,<{}dc:Relation>,<{}dc:Rights>,<{}dc:Source>,<{}dc:Subject>,<{}dc:Title>,<{}dc:Type>,<{}guide>,<{}item>,<{}itemref>,<{}manifest>,<{}meta>,<{}metadata>,<{}package>,<{}reference>,<{}site>,<{}spine>,<{}tour>,<{}tours>,<{}x-metadata> at com.sun.xml.internal.bind.v2.runtime.unmarshaller.UnmarshallingContext.handleEvent(UnmarshallingContext.java:631) at com.sun.xml.internal.bind.v2.runtime.unmarshaller.Loader.reportError(Loader.java:236) at com.sun.xml.internal.bind.v2.runtime.unmarshaller.Loader.reportError(Loader.java:231) at com.sun.xml.internal.bind.v2.runtime.unmarshaller.Loader.reportUnexpectedChildElement(Loader.java:105) at com.sun.xml.internal.bind.v2.runtime.unmarshaller.UnmarshallingContext$DefaultRootLoader.childElement(UnmarshallingContext.java:1038) at com.sun.xml.internal.bind.v2.runtime.unmarshaller.UnmarshallingContext._startElement(UnmarshallingContext.java:467) at com.sun.xml.internal.bind.v2.runtime.unmarshaller.UnmarshallingContext.startElement(UnmarshallingContext.java:448) at com.sun.xml.internal.bind.v2.runtime.unmarshaller.SAXConnector.startElement(SAXConnector.java:137) at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.startElement(AbstractSAXParser.java:501) at com.sun.org.apache.xerces.internal.impl.dtd.XMLDTDValidator.startElement(XMLDTDValidator.java:767) at com.sun.org.apache.xerces.internal.impl.XMLNSDocumentScannerImpl.scanStartElement(XMLNSDocumentScannerImpl.java:400) at com.sun.org.apache.xerces.internal.impl.XMLNSDocumentScannerImpl$NSContentDriver.scanRootElementHook(XMLNSDocumentScannerImpl.java:626) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl$FragmentContentDriver.next(XMLDocumentFragmentScannerImpl.java:3103) at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl$PrologDriver.next(XMLDocumentScannerImpl.java:922) at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl.next(XMLDocumentScannerImpl.java:648) at com.sun.org.apache.xerces.internal.impl.XMLNSDocumentScannerImpl.next(XMLNSDocumentScannerImpl.java:140) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanDocument(XMLDocumentFragmentScannerImpl.java:511) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:808) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:737) at com.sun.org.apache.xerces.internal.parsers.XMLParser.parse(XMLParser.java:119) at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.parse(AbstractSAXParser.java:1205) at com.sun.org.apache.xerces.internal.jaxp.SAXParserImpl$JAXPSAXParser.parse(SAXParserImpl.java:522) at com.sun.xml.internal.bind.v2.runtime.unmarshaller.UnmarshallerImpl.unmarshal0(UnmarshallerImpl.java:200) at com.sun.xml.internal.bind.v2.runtime.unmarshaller.UnmarshallerImpl.unmarshal(UnmarshallerImpl.java:173) at javax.xml.bind.helpers.AbstractUnmarshallerImpl.unmarshal(AbstractUnmarshallerImpl.java:137) at javax.xml.bind.helpers.AbstractUnmarshallerImpl.unmarshal(AbstractUnmarshallerImpl.java:142) at javax.xml.bind.helpers.AbstractUnmarshallerImpl.unmarshal(AbstractUnmarshallerImpl.java:151) at javax.xml.bind.helpers.AbstractUnmarshallerImpl.unmarshal(AbstractUnmarshallerImpl.java:169) at br.usp.lsi.pdtb.protector.view.ProtectorView.showBookData(ProtectorView.java:55) at br.usp.lsi.pdtb.protector.ProtectorImpl.openBook(ProtectorImpl.java:43) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at tomPack.swing.TomAction.actionPerformed(TomAction.java:115) at javax.swing.AbstractButton.fireActionPerformed(AbstractButton.java:1995) at javax.swing.AbstractButton$Handler.actionPerformed(AbstractButton.java:2318) at javax.swing.DefaultButtonModel.fireActionPerformed(DefaultButtonModel.java:387) at javax.swing.DefaultButtonModel.setPressed(DefaultButtonModel.java:242) at javax.swing.plaf.basic.BasicButtonListener.mouseReleased(BasicButtonListener.java:236) at java.awt.AWTEventMulticaster.mouseReleased(AWTEventMulticaster.java:272) at java.awt.Component.processMouseEvent(Component.java:6263) at javax.swing.JComponent.processMouseEvent(JComponent.java:3267) at java.awt.Component.processEvent(Component.java:6028) at java.awt.Container.processEvent(Container.java:2041) at java.awt.Component.dispatchEventImpl(Component.java:4630) at java.awt.Container.dispatchEventImpl(Container.java:2099) at java.awt.Component.dispatchEvent(Component.java:4460) at java.awt.LightweightDispatcher.retargetMouseEvent(Container.java:4574) at java.awt.LightweightDispatcher.processMouseEvent(Container.java:4238) at java.awt.LightweightDispatcher.dispatchEvent(Container.java:4168) at java.awt.Container.dispatchEventImpl(Container.java:2085) at java.awt.Window.dispatchEventImpl(Window.java:2478) at java.awt.Component.dispatchEvent(Component.java:4460) at java.awt.EventQueue.dispatchEvent(EventQueue.java:599) at java.awt.EventDispatchThread.pumpOneEventForFilters(EventDispatchThread.java:269) at java.awt.EventDispatchThread.pumpEventsForFilter(EventDispatchThread.java:184) at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:174) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:169) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:161) at java.awt.EventDispatchThread.run(EventDispatchThread.java:122) Any idea how to solve this?

Read the article
multiple valgrind errors: Conditional jump or move depends on uninitialised value(s)

- by Hristo

I'm running valgrind and I'm getting the following error (this is not the only one): ==21743== Conditional jump or move depends on uninitialised value(s) ==21743== at 0x4A06509: index (mc_replace_strmem.c:164) ==21743== by 0x33B7CBB3CD: gaih_inet (in /lib64/libc-2.5.so) ==21743== by 0x33B7CBD629: getaddrinfo (in /lib64/libc-2.5.so) ==21743== by 0x401A5F: tunnelURL (proxy.c:336) ==21743== by 0x40142A: client_thread (proxy.c:194) ==21743== by 0x33B8806616: start_thread (in /lib64/libpthread-2.5.so) ==21743== by 0x33B7CD3C2C: clone (in /lib64/libc-2.5.so) My tunnelURL() function looks like this: char * tunnelURL(char *url) { char * a = strstr(url, "//"); a += 2; char * path = strstr(a, "/"); char host[256]; strncpy (host, a, strlen(a)-strlen(path)); /* * The following is courtesy of Beej's Guide */ int status; int proxySocketFD; struct addrinfo hints; struct addrinfo *servinfo; // will point to the results memset(&hints, 0, sizeof(hints)); // make sure the struct is empty hints.ai_family = AF_INET; // don't care IPv4 or IPv6 hints.ai_socktype = SOCK_STREAM; // TCP stream sockets hints.ai_flags = AI_PASSIVE; // fill in my IP for me if ((status = getaddrinfo(host, "80", &hints, &servinfo)) != 0) { perror("getaddrinfo() fail"); exit(1); } // create socket if ((proxySocketFD = socket(servinfo->ai_family, servinfo->ai_socktype, servinfo->ai_protocol)) == -1) { perror("proxy socket() fail"); exit(1); } // connect if (connect(proxySocketFD, servinfo->ai_addr, servinfo->ai_addrlen) != 0) { printf("connect() fail"); exit(1); } // construct request char request[strlen(path) + strlen(host) + 26]; sprintf(request, "GET %s HTTP/1.1\r\nHost: %s\r\n\r\n", path, host); printf("%s", request); // send request send(proxySocketFD, request, strlen(request), 0); // receive response int i = 0; int amntRecvd = 0; char *pageContentBuffer = (char*) malloc(4096 * sizeof(char)); while ((amntRecvd = recv(proxySocketFD, pageContentBuffer + i, 4096, 0)) > 0) { i += amntRecvd; realloc(pageContentBuffer, i * 4096 * sizeof(char)); } // close proxy socket close(proxySocketFD); // deallocate memory freeaddrinfo(servinfo); return pageContentBuffer; } Line 336 corresponds to the if statement with the getaddrinfo() function call. I'm not really sure what I haven't initialized. The string I'm passing in "should" be already set... I'm printing it out just fine. I also get another error corresponding to the same line of code: ==21743== Use of uninitialised value of size 8 ==21743== at 0x33B7D05816: __nscd_cache_search (in /lib64/libc-2.5.so) ==21743== by 0x33B7D0438B: nscd_gethst_r (in /lib64/libc-2.5.so) ==21743== by 0x33B7D04B26: __nscd_gethostbyname2_r (in /lib64/libc-2.5.so) ==21743== by 0x33B7CE9F5E: gethostbyname2_r@@GLIBC_2.2.5 (in /lib64/libc-2.5.so) ==21743== by 0x33B7CBC522: gaih_inet (in /lib64/libc-2.5.so) ==21743== by 0x33B7CBD629: getaddrinfo (in /lib64/libc-2.5.so) ==21743== by 0x401A5F: tunnelURL (proxy.c:336) ==21743== by 0x40142A: client_thread (proxy.c:194) ==21743== by 0x33B8806616: start_thread (in /lib64/libpthread-2.5.so) ==21743== by 0x33B7CD3C2C: clone (in /lib64/libc-2.5.so) Any ideas as to what might becausing this? This is written in C btw... Thanks, Hristo

Read the article
PROJECT HELP NEEDED. SOME BASIC CONCEPTS GREAT CONFUSION BECAUSE OF LACK OF PROPER MATERIAL PLEASE H

- by user287745

Task ATTENDENCE RECORDER AND MANAGEMENT SYSTEM IN DISTRIBUTED ENVIRONMENT ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Example implementation needed. a main server in each lab where the operator punches in the attendence of the student. =========================================================== scenerio:- a college, 10 departments, all departments have a computer lab with 60-100 computers, the computers within each lab are interconnected and all computers in any department have to dail to a particular number (THE NUMBER GIVEN BY THE COLLEGE INTERNET DEPARTMENT) to get connected to the internet. therefore safe to assume that there is a central location to which all the computers in the college are connected to. there is a 'students attendence portal' which can be accessed using internet explorer, students enter there id and get the particular attendence record regarding to the labs only. a description of the working is like:- 1) the user will select which department, which year has arrived to the lab 2) the selection will give the user a return of all the students name and there roll numbers belonging to that department; 'with a check box to "TICK MARK IF THE STUDENT IS PRESENT" ' 3) A SUBMIT BUTTON when pressed reads the 'id' of the checkbox to determine the "particular count number of the student" from that an id of the student is constructed and that id is inserted with a present. (there is also date and time and much more to normalize the db and to avoid conflicts and keep historic records etc but that you will have to assume) steps taken till this date:- ( please note we are not computer students, we are to select something of some other line as a project!, as you will read in my many post 'i" have designed small websites just out of liking. have never ever done any thing official to implement like this.) * have made the database fully normalized. * have made the website which does the functions required on the database. Testing :- deployed the db and site on a free aspspider server and it worked. tested from several computers. Now the problem please help thank youuuuuuuu a practical demonstration has to be done within the college network. no internet! we have been assigned a lab - 60 computers- to demonstrate. (please dont give replies as 60 computers only! is not a big deal one CPU can manage it. i know that; IT IS A HYPOTHETICAL SITUATION WHERE WE ASSUME THAT 60 IS NOT 60 BUT ITS LIKE 60,000 COMPUTERS) 1a) make a web server, yes iis and put files in www folder and configure server to run aspx files- although a link to a step by step guide will be appreciated)\ ? which version of windows should i ask for xp or win server 2000 something? 2a) make a database server. ( well yes install sql server 2005, okay but then what? just put the database file on a pc share it and append the connection string to the share? ) 3a) make the site accessible from the remaining computers ? http://localhost/sitename ? all users "being operators of the particular lab" have the right to edit, write or delete(in dispute), thereby any "users" who hate our program can make the database inconsistent by accessing te same record and doing different edits and then complaining? so how to prevent this? you know something like when the db table is being written to others can only read but not write.. one big confusion:- IN DISTRIBUTED ENVIRONMENT "how to implement this" where does "distributed environment" come in! meaning :- alright the labs are in different departments but the "database server will be one" the "web server will be one" so whats distributed!?

Read the article
How to change by using CVGrayscaleMat

- by Babul

With the following code the image showed as above is converted as below image... Their it's showing black background with gray lines.....i want white background with gray lines .. Please guide me .. i am new to iPhone Thanks alot in Advance - (void)viewDidLoad { [super viewDidLoad]; // Initialise video capture - only supported on iOS device NOT simulator #if TARGET_IPHONE_SIMULATOR NSLog(@"Video capture is not supported in the simulator"); #else _videoCapture = new cv::VideoCapture; if (!_videoCapture->open(CV_CAP_AVFOUNDATION)) { NSLog(@"Failed to open video camera"); } #endif // Load a test image and demonstrate conversion between UIImage and cv::Mat UIImage *testImage = [UIImage imageNamed:@"testimage.jpg"]; double t; int times = 10; //-------------------------------- // Convert from UIImage to cv::Mat NSAutoreleasePool *pool = [[NSAutoreleasePool alloc] init]; t = (double)cv::getTickCount(); for (int i = 0; i < times; i++) { cv::Mat tempMat = [testImage CVMat]; } t = 1000 * ((double)cv::getTickCount() - t) / cv::getTickFrequency() / times; [pool release]; NSLog(@"UIImage to cv::Mat: %gms", t); //------------------------------------------ // Convert from UIImage to grayscale cv::Mat pool = [[NSAutoreleasePool alloc] init]; t = (double)cv::getTickCount(); for (int i = 0; i < times; i++) { cv::Mat tempMat = [testImage CVGrayscaleMat]; } t = 1000 * ((double)cv::getTickCount() - t) / cv::getTickFrequency() / times; [pool release]; NSLog(@"UIImage to grayscale cv::Mat: %gms", t); //-------------------------------- // Convert from cv::Mat to UIImage cv::Mat testMat = [testImage CVMat]; t = (double)cv::getTickCount(); for (int i = 0; i < times; i++) { UIImage *tempImage = [[UIImage alloc] initWithCVMat:testMat]; [tempImage release]; } t = 1000 * ((double)cv::getTickCount() - t) / cv::getTickFrequency() / times; NSLog(@"cv::Mat to UIImage: %gms", t); // Process test image and force update of UI _lastFrame = testMat; [self sliderChanged:nil]; } - (IBAction)capture:(id)sender { if (_videoCapture && _videoCapture->grab()) { (*_videoCapture) >> _lastFrame; [self processFrame]; } else { NSLog(@"Failed to grab frame"); } } - (void)processFrame { double t = (double)cv::getTickCount(); cv::Mat grayFrame, output; // Convert captured frame to grayscale cv::cvtColor(_lastFrame, grayFrame, cv::COLOR_RGB2GRAY); // Perform Canny edge detection using slide values for thresholds cv::Canny(grayFrame, output, _lowSlider.value * kCannyAperture * kCannyAperture, _highSlider.value * kCannyAperture * kCannyAperture, kCannyAperture); t = 1000 * ((double)cv::getTickCount() - t) / cv::getTickFrequency(); // Display result self.imageView.image = [UIImage imageWithCVMat:output]; self.elapsedTimeLabel.text = [NSString stringWithFormat:@"%.1fms", t]; }

Read the article
Performance required to improve Windows Experience Index?

- by Ian Boyd

Is there a guide on the metrics required to obtain a certain Windows Experience Index? A Microsoft guy said in January 2009: On the matter of transparency, it is indeed our plan to disclose in great detail how the scores are calculated, what the tests attempt to measure, why, and how they map to realistic scenarios and usage patterns. Has that amount of transparency happened? Is there a technet article somewhere? If my score was limited by my Memory subscore of 5.9. A nieve person would suggest: Buy a faster RAM Which is wrong of course. From the Windows help: If your computer has a 64-bit central processing unit (CPU) and 4 gigabytes (GB) or less random access memory (RAM), then the Memory (RAM) subscore for your computer will have a maximum of 5.9. You can buy the fastest, overclocked, liquid-cooled, DDR5 RAM on the planet; you'll still have a maximum Memory subscore of 5.9. So in general the knee-jerk advice "buy better stuff" is not helpful. What i am looking for is attributes required to achieve a certain score, or move beyond a current limitation. The information i've been able to compile so far, chiefly from 3 Windows blog entries, and an article: Memory subscore Score Conditions ======= ================================ 1.0 < 256 MB 2.0 < 500 MB 2.9 <= 512 MB 3.5 < 704 MB 3.9 < 944 MB 4.5 <= 1.5 GB 5.9 < 4.0GB-64MB on a 64-bit OS Windows Vista highest score 7.9 Windows 7 highest score Graphics Subscore Score Conditions ======= ====================== 1.0 doesn't support DX9 1.9 doesn't support WDDM 4.9 does not support Pixel Shader 3.0 5.9 doesn't support DX10 or WDDM1.1 Windows Vista highest score 7.9 Windows 7 highest score Gaming graphics subscore Score Result ======= ============================= 1.0 doesn't support D3D 2.0 supports D3D9, DX9 and WDDM 5.9 doesn't support DX10 or WDDM1.1 Windows Vista highest score 6.0-6.9 good framerates (e.g. 40-50fps) at normal resoltuions (e.g. 1280x1024) 7.0-7.9 even higher framerates at even higher resolutions 7.9 Windows 7 highest score Processor subscore Score Conditions ======= ========================================================================== 5.9 Windows Vista highest score 6.0-6.9 many quad core processors will be able to score in the high 6 low 7 ranges 7.0+ many quad core processors will be able to score in the high 6 low 7 ranges 7.9 8-core systems will be able to approach 8.9 Windows 7 highest score Primary hard disk subscore (note) Score Conditions ======= ======================================== 1.9 Limit for pathological drives that stop responding when pending writes 2.0 Limit for pathological drives that stop responding when pending writes 2.9 Limit for pathological drives that stop responding when pending writes 3.0 Limit for pathological drives that stop responding when pending writes 5.9 highest you're likely to see without SSD Windows Vista highest score 7.9 Windows 7 highest score Bonus Chatter You can find your WEI detailed test results in: C:\Windows\Performance\WinSAT\DataStore e.g. 2011-11-06 01.00.19.482 Disk.Assessment (Recent).WinSAT.xml <WinSAT> <WinSPR> <DiskScore>5.9</DiskScore> </WinSPR> <Metrics> <DiskMetrics> <AvgThroughput units="MB/s" score="6.4" ioSize="65536" kind="Sequential Read">89.95188</AvgThroughput> <AvgThroughput units="MB/s" score="4.0" ioSize="16384" kind="Random Read">1.58000</AvgThroughput> <Responsiveness Reason="UnableToAssess" Kind="Cap">TRUE</Responsiveness> </DiskMetrics> </Metrics> </WinSAT> Pre-emptive snarky comment: "WEI is useless, it has no relation to reality" Fine, how do i increase my hard-drive's random I/O throughput? Update - Amount of memory limits rating Some people don't believe Microsoft's statement that having less than 4GB of RAM on a 64-bit edition of Windows doesn't limit the rating to 5.9: And from xxx.Formal.Assessment (Recent).WinSAT.xml: <WinSPR> <LimitsApplied> <MemoryScore> <LimitApplied Friendly="Physical memory available to the OS is less than 4.0GB-64MB on a 64-bit OS : limit mem score to 5.9" Relation="LT">4227858432</LimitApplied> </MemoryScore> </LimitsApplied> </WinSPR> References Windows Vista Team Blog: Windows Experience Index: An In-Depth Look Understand and improve your computer's performance in Windows Vista Engineering Windows 7 Blog: Engineering the Windows 7 “Windows Experience Index”

Read the article
IIS7 FTP Setup - An error occured during the authentication process. 530 End Login failed

- by robmzd

I'm having a problem very similar to IIS 7.5 FTP IIS Manager Users Login Fail (530) on Windows Server 2008 R2 Standard. I have created an FTP site and IIS Manager user but am having trouble logging in. I could really do with getting this working with the IIS Manager user rather than by creating a new system user since I'm fairly restricted with those accounts. Here is the output when connecting locally through command prompt: C:\Windows\system32>ftp localhost Connected to MYSERVER. 220 Microsoft FTP Service User (MYSERVER:(none)): MyFtpLogin 331 Password required for MyFtpLogin. Password: *** 530-User cannot log in. Win32 error: Logon failure: unknown user name or bad password. Error details: An error occured during the authentication process. 530 End Login failed. I have followed the guide to configure ftp with iis manager authentication in iis 7 and Adding FTP Publishing to a Web Site in IIS 7 Things I have done and checked: The FTP Service is installed (along with FTP Extensibility). Local Service and Network Service have been given access to the site folder Permission has been given to the config files Granted read/write permissions to the FTP Root folder The Management Service is installed and running Enable remote connections is ticked with 'Windows credentials or IIS manager credentials' selected The IIS Manager User has been added to the server (root connection in the IIS connections branch) The new FTP site has been added IIS Manager Authentication has been added to the FTP authentication providers The IIS Manager user has been added to the IIS Manager Permissions list for the site Added Read/Write permissions for the user in the FTP Authorization Rules Here's a section of the applicationHost config file associated with the FTP site <site name="MySite" id="8"> <application path="/" applicationPool="MyAppPool"> <virtualDirectory path="/" physicalPath="D:\Websites\MySite" /> </application> <bindings> <binding protocol="http" bindingInformation="*:80:www.mydomain.co.uk" /> <binding protocol="ftp" bindingInformation="*:21:www.mydomain.co.uk" /> </bindings> <ftpServer> <security> <ssl controlChannelPolicy="SslAllow" dataChannelPolicy="SslAllow" /> <authentication> <basicAuthentication enabled="true" /> <customAuthentication> <providers> <add name="IisManagerAuth" enabled="true" /> </providers> </customAuthentication> </authentication> </security> </ftpServer> </site> ... <location path="MySite"> <system.ftpServer> <security> <authorization> <add accessType="Allow" users="MyFtpLogin" permissions="Read, Write" /> </authorization> </security> </system.ftpServer> </location> If I connect to the Site (not FTP) from my local IIS Manager using the same IIS Manager account details then it connects fine, I can browse files and change settings as I would locally (though I don't seem to have an option to upload files). Trying to connect via FTP though either through the browser or FileZilla etc... gives me: Status: Resolving address of www.mydomain.co.uk Status: Connecting to 123.456.12.123:21... Status: Connection established, waiting for welcome message... Response: 220 Microsoft FTP Service Command: USER MyFtpLogin Response: 331 Password required for MyFtpLogin. Command: PASS ********* Response: 530 User cannot log in. Error: Critical error Error: Could not connect to server I have tried collecting etw traces for ftp sessions, in the logs I get a FailBasicLogon followed by a FailCustomLogon, but no other info: FailBasicLogon SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | ErrorCode=0x8007052E StartCustomLogon SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | LogonProvider=IisManagerAuth StartCallProvider SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | provider=IisManagerAuth EndCallProvider SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} EndCustomLogon SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} FailCustomLogon SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | ErrorCode=0x8007052E FailFtpCommand SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | ReturnValue=0x8007052E | SubStatus=ERROR_DURING_AUTHENTICATION In the normal FTP logs I just get: 2012-10-23 16:13:11 123.456.12.123 - 123.456.12.123 21 ControlChannelOpened - - 0 0 e2d4e935-fb31-4f2c-af79-78d75d47c18e - 2012-10-23 16:13:11 123.456.12.123 - 123.456.12.123 21 USER MyFtpLogin 331 0 0 e2d4e935-fb31-4f2c-af79-78d75d47c18e - 2012-10-23 16:13:11 123.456.12.123 - 123.456.12.123 21 PASS *** 530 1326 41 e2d4e935-fb31-4f2c-af79-78d75d47c18e - 2012-10-23 16:13:11 123.456.12.123 - 123.456.12.123 21 ControlChannelClosed - - 0 0 e2d4e935-fb31-4f2c-af79-78d75d47c18e - If anyone has any ideas than I would be very grateful to hear them. Many thanks.

Read the article
how to get vendor id and product id of a plugged usb device on windows

- by new

Hello all, I am using Qt on windows platform. i want to get and display vendor id and product id of a plugged usb device from my local system. Below is my full source code to get the vendor id and product id from the usb device. when i run the my qt application it does not throw me any errors . so i plug the usb device into the system. but my print statement displays the result as below qDebug ()<DevicePath; i get the result as 0x4 Whether i have any implementation mistakes in my source code ? if so please guide me what i am doing wrong.. Have i missed out any other functions ? Is it possible to get the vendor id and product id from the usb device based on my source code .( my implementation of the code ) ? kindly find my source code below static GUID GUID_DEVINTERFACE_USB_DEVICE = { 0xA5DCBF10L, 0x6530, 0x11D2, { 0x90, 0x1F, 0x00, 0xC0, 0x4F, 0xB9, 0x51, 0xED } }; HANDLE hInfo = SetupDiGetClassDevs(&GUID_DEVINTERFACE_USB_DEVICE,NULL,NULL,DIGCF_PRESENT | DIGCF_INTERFACEDEVICE); if ( hInfo == INVALID_HANDLE_VALUE ) { qDebug ()<<"invalid"; } else { qDebug ()<<"valid handle"; SP_DEVINFO_DATA DeviceInfoData; DeviceInfoData.cbSize = sizeof(SP_DEVINFO_DATA); SP_INTERFACE_DEVICE_DATA Interface_Info; Interface_Info.cbSize = sizeof(Interface_Info); BYTE Buf[1024]; DWORD i; DWORD InterfaceNumber= 0; PSP_DEVICE_INTERFACE_DETAIL_DATA pspdidd = (PSP_DEVICE_INTERFACE_DETAIL_DATA)Buf; for (i=0;SetupDiEnumDeviceInfo(hInfo,i,&DeviceInfoData);i++) { DWORD DataT; LPTSTR buffer = NULL; DWORD buffersize = 0; while (!SetupDiGetDeviceRegistryProperty( hInfo,&DeviceInfoData,SPDRP_DEVICEDESC,&DataT,(PBYTE)buffer,buffersize,&buffersize)) { if (GetLastError() == ERROR_INSUFFICIENT_BUFFER) { // Change the buffer size. if (buffer) LocalFree(buffer); buffer = (LPTSTR)LocalAlloc(LPTR,buffersize); } else { // Insert error handling here. break; } qDebug ()<<(TEXT("Device Number %i is: %s\n"),i, buffer); if (buffer) LocalFree(buffer); if ( GetLastError()!=NO_ERROR && GetLastError()!=ERROR_NO_MORE_ITEMS ) { // Insert error handling here. qDebug ()<<"return false"; } InterfaceNumber = 0; // this just returns the first one, you can iterate on this if (SetupDiEnumDeviceInterfaces(hInfo,NULL,&GUID_DEVINTERFACE_USB_DEVICE,InterfaceNumber,&Interface_Info)) { printf("Got interface"); DWORD needed; pspdidd->cbSize = sizeof(*pspdidd); SP_DEVICE_INTERFACE_DETAIL_DATA *pDetData = NULL; DWORD dwDetDataSize = sizeof (SP_DEVICE_INTERFACE_DETAIL_DATA) + 256; SetupDiGetDeviceInterfaceDetail(hInfo, &Interface_Info, pDetData,dwDetDataSize, NULL,&DeviceInfoData); qDebug ()<<pDetData->DevicePath; //qDebug ()<<QString::fromWCharArray(pDetData->DevicePath); } else { printf("\nNo interface"); //ErrorExit((LPTSTR) "SetupDiEnumDeviceInterfaces"); if ( GetLastError() == ERROR_NO_MORE_ITEMS) printf(", since there are no more items found."); else printf(", unknown reason."); } // Cleanup SetupDiDestroyDeviceInfoList(hInfo); qDebug ()<<"return true"; } } }

Read the article
How to validate and entry on a datagrid that is bound to an adapter

- by Ziv

Hi, I've been using C# for a while and began a program now to learn WPF-which means I know almost nothing of it. I used this tutorial as a guide to do what I wanted to do (which is binding a database to a datagrid), after a hard struggle to add the adapter as the source of the datagrid I now want to enable editing with validation on some of the cells. My problem is that the data is sent straight from the adapter and not through an object collection (I had a hard time getting to this situation, see the first half of the tutorial on how to bind the adapter and dataset through the resources) but the tutorial doesn't show a way to validate the datagrid if the data is sent through an adapter-only through a collection. To make it clear-how do I validate input in a datagrid that is bound to an adapter through a resource? The relevant code: (XAML) <Window.Resources> <ObjectDataProvider x:Key="DiscsDataProvider" ObjectType="{x:Type local:DiscsDataProvider}" /> <ObjectDataProvider x:Key="Discs" ObjectInstance="{StaticResource ResourceKey=DiscsDataProvider}" MethodName="GetDiscs" /> <Style x:Key="CellEditStyle" TargetType="{x:Type TextBox}"> <Setter Property="BorderThickness" Value="0"/> <Setter Property="Padding" Value="0"/> <Setter Property="Background" Value="Yellow"/> <Style.Triggers> <Trigger Property="Validation.HasError" Value="true"> <Setter Property="ToolTip" Value="{Binding RelativeSource={RelativeSource Self}, Path=(Validation.Errors)[0].ErrorContent}"/> </Trigger> </Style.Triggers> </Style> </Window.Resources> For the datagrid: <Grid Width="auto" Height="auto"> <DockPanel DataContext="{Binding Source={StaticResource ResourceKey=Discs}}"> <DataGrid Margin="12,0,0,12" Name="View_dg" HorizontalAlignment="Left" Width="533" Height="262" VerticalAlignment="Bottom" ItemsSource="{Binding}" AutoGenerateColumns="False" CanUserAddRows="False" CanUserDeleteRows="False" CanUserResizeColumns="True"> <DataGrid.Columns> <DataGridTextColumn Binding="{Binding Path=ContainerID}" CanUserReorder="False" CanUserResize="True" CanUserSort="True" EditingElementStyle="{StaticResource CellEditStyle}" IsReadOnly="False" Header="Container" /> <DataGridTextColumn Binding="{Binding Path=ID}" CanUserReorder="False" CanUserResize="True" CanUserSort="True" EditingElementStyle="{StaticResource CellEditStyle}" IsReadOnly="True" Header="ID" /> <DataGridTextColumn Binding="{Binding Path=Title}" CanUserReorder="False" CanUserResize="True" CanUserSort="True" EditingElementStyle="{StaticResource CellEditStyle}" IsReadOnly="False" Header="Title" /> <DataGridTextColumn Binding="{Binding Path=SubTitle}" CanUserReorder="False" CanUserResize="True" CanUserSort="False" EditingElementStyle="{StaticResource CellEditStyle}" IsReadOnly="False" Header="Sub Title" /> <DataGridTextColumn Binding="{Binding Path=Type}" CanUserReorder="False" CanUserResize="True" CanUserSort="True" EditingElementStyle="{StaticResource CellEditStyle}" IsReadOnly="False" Header="Type" /> <DataGridTextColumn Binding="{Binding Path=Volume}" CanUserReorder="False" CanUserResize="True" CanUserSort="False" EditingElementStyle="{StaticResource CellEditStyle}" IsReadOnly="False" Header="Volume" /> <DataGridTextColumn Binding="{Binding Path=TotalDiscs}" CanUserReorder="False" CanUserResize="True" CanUserSort="False" EditingElementStyle="{StaticResource CellEditStyle}" IsReadOnly="False" Header="Total Discs" /> </DataGrid.Columns> </DataGrid> </DockPanel> and C#: public class DiscsDataProvider { private DiscsTableAdapter adapter; private DB dataset; public DiscsDataProvider() { dataset = new DB(); adapter = new DiscsTableAdapter(); adapter.Fill(dataset.Discs); } public DataView GetDiscs() { return dataset.Discs.DefaultView; } }

Read the article
CustomListAdapter Problem in Android? Getting ClassCast Exception? How???

- by Praveen Chandrasekaran

i want to improve the list view's performance. this is the code for my getView method in my Adapter? public View getView(int arg0, View text_view_name, ViewGroup parent) { try { if (text_view_name == null) { text_view_name = mInflater.inflate( R.layout.bs_content_list_item1, null); text_view_name.setTag(R.id.text1_detail1, text_view_name .findViewById(R.id.text1_detail1)); text_view_name.setTag(R.id.text3_detail1, text_view_name .findViewById(R.id.text3_detail1)); text_view_name.setTag(R.id.eve_img_detail1, text_view_name .findViewById(R.id.eve_img_detail1)); } text1 = (TextView) text_view_name.getTag(R.id.text1_detail1); // text2 = (TextView) text_view_name.getTag(R.id.text2); text3 = (TextView) text_view_name.getTag(R.id.text3_detail1); img = (ImageView) text_view_name.getTag(R.id.eve_img_detail1); text1.setText(VAL1[arg0]); text3.setText(VAL3[arg0]); if (!mBusy) { img_value = new URL(VAL4[arg0]); mIcon11 = BitmapFactory.decodeStream(img_value.openConnection() .getInputStream()); img.setImageBitmap(mIcon11); text_view_name.setTag(R.id.eve_img_detail1, null); } else { img.setImageResource(R.drawable.icon); text_view_name.setTag(R.id.eve_img_detail1, text_view_name .findViewById(R.id.eve_img_detail1)); } } catch (Exception e) { name = "Exception in MultiLine_bar_details1 getView"; Log.v(TAG, name + e); } return text_view_name; } this is the code for scrollstatechanged method: public void onScrollStateChanged(AbsListView view, int scrollState) { switch (scrollState) { case OnScrollListener.SCROLL_STATE_IDLE: try { MultiLine_bar_details1.mBusy = false; int first = view.getFirstVisiblePosition(); int count = view.getCount(); for (int i = 0; i < count; i++) { ImageView t = (ImageView) view.getChildAt(i);// here getting the ClassCastException if (t.getTag(R.id.eve_img_detail1) != null) { MultiLine_bar_details1.img_value = new URL( MultiLine_bar_details1.VAL4[first + i]); MultiLine_bar_details1.mIcon11 = BitmapFactory .decodeStream(MultiLine_bar_details1.img_value .openConnection().getInputStream()); MultiLine_bar_details1.img.setImageBitmap(MultiLine_bar_details1.mIcon11); t.setTag(R.id.eve_img_detail1, null); } } } catch (Exception e) { Log.v(TAG, "Idle" + e); } // mStatus.setText("Idle"); break; case OnScrollListener.SCROLL_STATE_TOUCH_SCROLL: MultiLine_bar_details1.mBusy = true; break; case OnScrollListener.SCROLL_STATE_FLING: MultiLine_bar_details1.mBusy = true; break; } } getting the Exception in Idle state: 05-03 16:47:15.201: VERBOSE/BS_Bars(258): Idlejava.lang.ClassCastException: android.widget.LinearLayout this is very complicated for me to get the output properly. actually i have the listview with custom adapter. that icons makes the listview scroll very slow.i am getting the images for icons from the image urls. upto this(above code) i can improve the scroll performance of my list view. but the image icons are not proper in the corresponding order. its dynamically changing when i scroll the listview.. i refered the commonsware busy coder guide and this blog. My very Big question is "How can we access the single view in scrollstatechanged parameter AbsListView? " what is the problem in it? how to do it better? Any Idea?

Read the article
CustomListAdapter Problem in Android? How???

- by Praveen Chandrasekaran

i want to improve the list view's performance. this is the code for my getView method in my Adapter? public View getView(int arg0, View text_view_name, ViewGroup parent) { try { if (text_view_name == null) { text_view_name = mInflater.inflate( R.layout.bs_content_list_item1, null); text_view_name.setTag(R.id.text1_detail1, text_view_name .findViewById(R.id.text1_detail1)); text_view_name.setTag(R.id.text3_detail1, text_view_name .findViewById(R.id.text3_detail1)); text_view_name.setTag(R.id.eve_img_detail1, text_view_name .findViewById(R.id.eve_img_detail1)); } text1 = (TextView) text_view_name.getTag(R.id.text1_detail1); // text2 = (TextView) text_view_name.getTag(R.id.text2); text3 = (TextView) text_view_name.getTag(R.id.text3_detail1); img = (ImageView) text_view_name.getTag(R.id.eve_img_detail1); text1.setText(VAL1[arg0]); text3.setText(VAL3[arg0]); if (!mBusy) { img_value = new URL(VAL4[arg0]); mIcon11 = BitmapFactory.decodeStream(img_value.openConnection() .getInputStream()); img.setImageBitmap(mIcon11); text_view_name.setTag(R.id.eve_img_detail1, null); } else { img.setImageResource(R.drawable.icon); text_view_name.setTag(R.id.eve_img_detail1, text_view_name .findViewById(R.id.eve_img_detail1)); } } catch (Exception e) { name = "Exception in MultiLine_bar_details1 getView"; Log.v(TAG, name + e); } return text_view_name; } this is the code for scrollstatechanged method: public void onScrollStateChanged(AbsListView view, int scrollState) { switch (scrollState) { case OnScrollListener.SCROLL_STATE_IDLE: try { MultiLine_bar_details1.mBusy = false; int first = view.getFirstVisiblePosition(); int count = view.getCount(); for (int i = 0; i < count; i++) { ImageView t = (ImageView) view.getChildAt(i); if (t.getTag(R.id.eve_img_detail1) != null) { MultiLine_bar_details1.img_value = new URL( MultiLine_bar_details1.VAL4[first + i]); MultiLine_bar_details1.mIcon11 = BitmapFactory .decodeStream(MultiLine_bar_details1.img_value .openConnection().getInputStream()); MultiLine_bar_details1.img.setImageBitmap(MultiLine_bar_details1.mIcon11); t.setTag(R.id.eve_img_detail1, null); } } } catch (Exception e) { Log.v(TAG, "Idle" + e); } // mStatus.setText("Idle"); break; case OnScrollListener.SCROLL_STATE_TOUCH_SCROLL: MultiLine_bar_details1.mBusy = true; break; case OnScrollListener.SCROLL_STATE_FLING: MultiLine_bar_details1.mBusy = true; break; } } this is very complicated for me to get the output properly. actually i have the listview with custom adapter. that icons makes the listview scroll very slow.i am getting the images for icons from the image urls. upto this(above code) i can improve the scroll performance of my list view. but the image icons are not proper in the corresponding order. its dynamically changing when i scroll the listview.. i refered the commonsware busy coder guide and this blog. My very Big question is "How can we access the single view in scrollstatechanged parameter AbsListView? " what is the problem in it? how to do it better? Any Idea?

Read the article
Installing Windows on HP Proliant Servers without SmartStart

- by Fitzroy

I have a PXE server for deploying Windows XP and Windows 7 to workstations. The process is as follows: Boot the workstation from the NIC. Workstation sends a DHCP request. DHCP server responds with an IP address and the location of the PXE server. Workstation downloads WinPE image file from PXE server via TFTP Workstation stores WinPE image file in memory and executes it. Once booted into WinPE, I connect to a network share to gain access to either the Windows XP or Windows 7 installation files. A custom script is launched to guide you through the process of formatting and partitioning the hard drive(s) (using DISKPART and FORMAT). Another custom script asks for details such as the hostname to assign to the workstation. The answers provided are used to build an unattended answer file (SIF [Setup Information File] for WinXP and XML for Win7). The Windows setup EXE is launched, passing the unattended answer file to it as a parameter. The Windows XP and Windows 7 installation sources have been customised to include the drivers for our Dell workstations. They also run a number of scripts upon first booting up to install software packages. This process works very well for our workstations and I would now like to use it for building our servers too. The vast majority of our servers are HP Proliant DL360 G6, DL380 G5 and DL380 G6. They’re running Windows Server 2003 (various editions) or 2008 (various editions). To date, we have always built the HP Proliant servers using the SmartStart CD provided. SmartStart does three useful things for us: Setup RAID with HP Array Configuration Utility (ACU). Installs and configures SNMP Installs various HP Tools for Windows (HP Array Configuration Utility, HP Array Diagnostic Utility, HP Proliant Integrated Management Log Viewer, etc) Using SmartStart I have never had to manually download and install Windows drivers for network, sound, video, etc. I'm not sure if this is because SmartStart copies drivers from the CD during setup, or whether Windows just has the drivers natively in its driver CAB. If I abandon the SmartStart CD in favour of my PXE server I would have to do the following: As I wont have access to ACU, I'll configure the RAID (before booting to the PXE server) by pressing F8 (during the boot process) to access Option ROM Configuration for Arrays (ORCA). Installation of SNMP and the HP Tools will have to be installed once the Windows installation is complete using the Proliant Support Pack. Is this method OK? Is there anything that the SmartStart CD does that I'll be unable to do by other means? Are there any disadvantages to not using the SmartStart CD? Many thanks. UPDATE 05/01/12 I’ve been reading through the SmartStart Scripting Toolkit documentation. The scripting toolkit contains command line tools which work within WinPE and can such things as configure BIOS settings, configure an array and setup ILO. I’m personally not too bothered about configuring BIOS settings as I rarely deviate from the defaults (unless the server is to be a Hyper-V host). I’m not too fussed about being able to configure the array from within WinPE, as I’m happy to just press F8 and use Option ROM Configuration for Arrays (ORCA). Although, if it’s easy enough to do, I will explore this further, as it saves time if everything can be configured from within WinPE. One of the nice features all the tools possess is that you can pass input files to them. EG. Configure one server to your requirements, capture its configuration to a file (using the appropriate tool), you can then use the tool on other servers passing the input file with the captured configuration. Array controller drivers appear to be included with the toolkit along with example of how to incorporate them within a WinPE build. I suppose WinPE won’t be able to see logical volumes (I.E 2x physical disks in a RAID 1 configuration) without the array controller drivers? I mentioned in my post that SmartStart normally installs a bunch of Windows HP tools for you. I’ve had a look today, and if you run the SmartStart CD from within Windows all the tools can be installed. Therefore I can do this after the Windows installation is complete. The SmartStart CD appears to contain a lot Windows drivers. I can customise my Windows 2008 source to incorporate these drivers. However, I understand that incorporating an array controller driver is a little different to most drivers. I believe that you have to provide the driver during the very early stages of the Windows setup. I’m working through the Scripting Toolkit documentation to try and work this out...

Read the article
How to query with the datetime value using LINQ to XML ?

- by Shailesh Jaiswal

I am developing window phone 7 application in silverlight. I am new to the silverlight. I am also new to LINQ to XML. In my application the user select the date & submit some transaction details into the application. The details gets stored in XML File. I am using the custom date control in my application for the date selection as follows private void DatePicker_ValueChanged(object sender, DateTimeValueChangedEventArgs e) { AppObj = Application.Current as App; AppObj.date = (DateTime)EntryDate.Value; } Then the value of AppObj.date gets stored in the XML file. Sometimes I use the DateTime.Now to store the date in the XML File. Now I want to generate the report of submitted transaction details by querying through LINQ to XML. I want to generate the report for today's date, current week & current month. For this purpose I am using the following code public void GetTransactionObjects(String strXMLFile, DateTime VDateTime) { XDocument doc = null; XMLFileManager XMLDocObj = new XMLFileManager(); doc = XMLDocObj.LoadXMLFile(strXMLFile); var vTransaction = from s in doc.Descendants("Transaction") .Where(x => x.Element("Current_Date").Value == VDateTime.ToShortDateString()) select new Transaction(s); this.Clear(); AddRange(vTransaction); } The Transaction class contains the following constructor. public Transaction(XElement xElement) { Transaction_ID = Convert.ToInt32(xElement.Element("Transaction_ID").Value.ToString()); TransactionType_ID = Convert.ToInt32(xElement.Element("TransactionType_ID").Value.ToString()); Alphabet_ID = Convert.ToInt32(xElement.Element("Alphabet_ID").Value.ToString()); ID = Convert.ToInt32(xElement.Element("ID").Value.ToString()); SubCategory_ID = Convert.ToInt32(xElement.Element("SubCategory_ID").Value.ToString()); Item_ID = Convert.ToInt32(xElement.Element("Item_ID").Value.ToString()); Currency_ID = Convert.ToInt32(xElement.Element("Currency_ID").Value.ToString()); InputTypeMethod_ID = Convert.ToInt32(xElement.Element("InputTypeMethod_ID").Value.ToString()); Principle = Convert.ToInt32(xElement.Element("InputTypeMethod_ID").Value.ToString()); Interest = Convert.ToInt32(xElement.Element("Interest").Value.ToString()); ROI = Convert.ToInt32(xElement.Element("InputTypeMethod_ID").Value.ToString()); Amount = Convert.ToInt32(xElement.Element("InputTypeMethod_ID").Value.ToString()); Current_Date = Convert.ToDateTime(xElement.Element("Current_Date").Value.ToString()); } In the XML File the value gets stored for date & time. The value gets stored as follows 0 0 3 0 0 0 3 0 0 0 0 5000 2010-12-31T18:08:23.433+05:30 Look at the node <Current_Date>2010-12-31T18:08:23.433+05:30</Current_Date> The date format is yyyy-mm-dd. Now how should I write the following query to get all the submitted transaction details for today's date ? var vTransaction = from s in doc.Descendants("Transaction") .Where(x => x.Element("Current_Date").Value == VDateTime.ToShortDateString()) select new Transaction(s); Similarly how should I write the query to get all the transaction details for the current week & current month? Can you please provide me any code or link through which I can resolve the above issue ? If I am doing anything wrong then please guide me.

Read the article
How to save data from multiple views of an iPhone app?

- by DownUnder

Hi Everyone. I'm making an app where I need to save the text in multiple views in the app when the app quits. I also need to be able to remove all of the data from just one of those views and when the app quits, it's possible not all of those views will have been created yet. After reading this post I thought perhaps it would be good to use a singleton that manages my app data which loads in the data when it is first requested and saved it when the app quits. Then in each view where I need to save data I can just set it on the singleton. I gave it a go but have run into some issues. At first I didn't synthesize the properties (as in the post I was using as a guide) but the compiler told me I needed to make getters and setters, so I did. Now when my applicationWIllTerminate: gets call the app crashes and the console says "Program received signal: “EXC_BAD_ACCESS”. kill quit". Is anyone able to tell me what I'm doing wrong, or suggest a better approach to saving the data? //SavedData.h #import <Foundation/Foundation.h> #define kFileName @"appData.plist" @interface SavedData : NSObject { NSString *information; NSString *name; NSString *email; NSString *phone; NSString *mobile; } @property(assign) NSString *information; @property(assign) NSString *name; @property(assign) NSString *email; @property(assign) NSString *phone; @property(assign) NSString *mobile; + (SavedData *)singleton; + (NSString *)dataFilePath; + (void)applicationWillTerminate:(NSNotification *)notification; @end //SavedData.m #import "SavedData.h" @implementation SavedData @synthesize information; @synthesize name; @synthesize email; @synthesize phone; @synthesize mobile; static SavedData * SavedData_Singleton = nil; + (SavedData *)singleton{ if (nil == SavedData_Singleton){ SavedData_Singleton = [[SavedData_Singleton alloc] init]; NSString *filePath = [self dataFilePath]; if([[NSFileManager defaultManager] fileExistsAtPath:filePath]){ NSMutableArray * array = [[NSMutableArray alloc] initWithContentsOfFile:filePath]; information = [array objectAtIndex:0]; name = [array objectAtIndex:1]; email = [array objectAtIndex:2]; phone = [array objectAtIndex:3]; mobile = [array objectAtIndex:4]; [array release]; } UIApplication *app = [UIApplication sharedApplication]; [[NSNotificationCenter defaultCenter] addObserver:self selector:@selector(applicationWillTerminate:) name:UIApplicationWillTerminateNotification object:app]; } return SavedData_Singleton; } + (NSString *)dataFilePath{ NSArray *paths = NSSearchPathForDirectoriesInDomains(NSDocumentDirectory, NSUserDomainMask, YES); NSString *DocumentsDirectory = [paths objectAtIndex:0]; return [DocumentsDirectory stringByAppendingPathComponent:kFileName]; } + (void)applicationWillTerminate:(NSNotification *)notification{ NSLog(@"Application will terminate received"); NSMutableArray *array = [[NSMutableArray alloc] init]; [array addObject:information]; [array addObject:name]; [array addObject:email]; [array addObject:phone]; [array addObject:mobile]; [array writeToFile:[self dataFilePath] atomically:YES]; [array release]; } @end Then when I want to use it I do myLabel.text = [SavedData singleton].information; And when I change the field [SavedData singleton].information = @"my string"; Any help will be very much appreciated!

Read the article
Best style for Python programs: what do you suggest?

- by Noctis Skytower

A friend of mine wanted help learning to program, so he gave me all the programs that he wrote for his previous classes. The last program that he wrote was an encryption program, and after rewriting all his programs in Python, this is how his encryption program turned out (after adding my own requirements). #! /usr/bin/env python ################################################################################ """\ CLASS INFORMATION ----------------- Program Name: Program 11 Programmer: Stephen Chappell Instructor: Stephen Chappell for CS 999-0, Python Due Date: 17 May 2010 DOCUMENTATION ------------- This is a simple encryption program that can encode and decode messages.""" ################################################################################ import sys KEY_FILE = 'Key.txt' BACKUP = '''\ !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNO\ PQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~ _@/6-UC'GzaV0%5Mo9g+yNh8b">Bi=<Lx [sQn#^R.D2Xc(\ Jm!4e${lAEWud&t7]H\`}pvPw)FY,Z~?qK|3SOfk*:1;jTrI''' ################################################################################ def main(): "Run the program: loads key, runs processing loop, and saves key." encode_map, decode_map = load_key(KEY_FILE) try: run_interface_loop(encode_map, decode_map) except SystemExit: pass save_key(KEY_FILE, encode_map) def run_interface_loop(encode_map, decode_map): "Shows the menu and runs the appropriate command." print('This program handles encryption via a customizable key.') while True: print('''\ MENU ==== (1) Encode (2) Decode (3) Custom (4) Finish''') switch = get_character('Select: ', tuple('1234')) FUNC[switch](encode_map, decode_map) def get_character(prompt, choices): "Gets a valid menu option and returns it." while True: sys.stdout.write(prompt) sys.stdout.flush() line = sys.stdin.readline()[:-1] if not line: sys.exit() if line in choices: return line print(repr(line), 'is not a valid choice.') ################################################################################ def load_key(filename): "Gets the key file data and returns encoding/decoding dictionaries." plain, cypher = open_file(filename) return dict(zip(plain, cypher)), dict(zip(cypher, plain)) def open_file(filename): "Load the keys and tries to create it when not available." while True: try: with open(filename) as file: plain, cypher = file.read().split('\n') return plain, cypher except: with open(filename, 'w') as file: file.write(BACKUP) def save_key(filename, encode_map): "Dumps the map into two buffers and saves them to the key file." plain = cypher = str() for p, c in encode_map.items(): plain += p cypher += c with open(filename, 'w') as file: file.write(plain + '\n' + cypher) ################################################################################ def encode(encode_map, decode_map): "Encodes message for the user." print('Enter your message to encode (EOF when finished).') message = get_message() for char in message: sys.stdout.write(encode_map[char] if char in encode_map else char) def decode(encode_map, decode_map): "Decodes message for the user." print('Enter your message to decode (EOF when finished).') message = get_message() for char in message: sys.stdout.write(decode_map[char] if char in decode_map else char) def custom(encode_map, decode_map): "Allows user to edit the encoding/decoding dictionaries." plain, cypher = get_new_mapping() for p, c in zip(plain, cypher): encode_map[p] = c decode_map[c] = p ################################################################################ def get_message(): "Gets and returns text entered by the user (until EOF)." buffer = [] while True: line = sys.stdin.readline() if line: buffer.append(line) else: return ''.join(buffer) def get_new_mapping(): "Prompts for strings to edit encoding/decoding maps." while True: plain = get_unique_chars('What do you want to encode from?') cypher = get_unique_chars('What do you want to encode to?') if len(plain) == len(cypher): return plain, cypher print('Both lines should have the same length.') def get_unique_chars(prompt): "Gets strings that only contain unique characters." print(prompt) while True: line = input() if len(line) == len(set(line)): return line print('There were duplicate characters: please try again.') ################################################################################ # This map is used for dispatching commands in the interface loop. FUNC = {'1': encode, '2': decode, '3': custom, '4': lambda a, b: sys.exit()} ################################################################################ if __name__ == '__main__': main() For all those Python programmers out there, your help is being requested. How should the formatting (not necessarily the coding by altered to fit Python's style guide? My friend does not need to be learning things that are not correct. If you have suggestions on the code, feel free to post them to this wiki as well.

Read the article
Differing styles in Python program: what do you suggest?

- by Noctis Skytower

A friend of mine wanted help learning to program, so he gave me all the programs that he wrote for his previous classes. The last program that he wrote was an encryption program, and after rewriting all his programs in Python, this is how his encryption program turned out (after adding my own requirements). #! /usr/bin/env python ################################################################################ """\ CLASS INFORMATION ----------------- Program Name: Program 11 Programmer: Stephen Chappell Instructor: Stephen Chappell for CS 999-0, Python Due Date: 17 May 2010 DOCUMENTATION ------------- This is a simple encryption program that can encode and decode messages.""" ################################################################################ import sys KEY_FILE = 'Key.txt' BACKUP = '''\ !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNO\ PQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~ _@/6-UC'GzaV0%5Mo9g+yNh8b">Bi=<Lx [sQn#^R.D2Xc(\ Jm!4e${lAEWud&t7]H\`}pvPw)FY,Z~?qK|3SOfk*:1;jTrI''' ################################################################################ def main(): "Run the program: loads key, runs processing loop, and saves key." encode_map, decode_map = load_key(KEY_FILE) try: run_interface_loop(encode_map, decode_map) except SystemExit: pass save_key(KEY_FILE, encode_map) def run_interface_loop(encode_map, decode_map): "Shows the menu and runs the appropriate command." print('This program handles encryption via a customizable key.') while True: print('''\ MENU ==== (1) Encode (2) Decode (3) Custom (4) Finish''') switch = get_character('Select: ', tuple('1234')) FUNC[switch](encode_map, decode_map) def get_character(prompt, choices): "Gets a valid menu option and returns it." while True: sys.stdout.write(prompt) sys.stdout.flush() line = sys.stdin.readline()[:-1] if not line: sys.exit() if line in choices: return line print(repr(line), 'is not a valid choice.') ################################################################################ def load_key(filename): "Gets the key file data and returns encoding/decoding dictionaries." plain, cypher = open_file(filename) return dict(zip(plain, cypher)), dict(zip(cypher, plain)) def open_file(filename): "Load the keys and tries to create it when not available." while True: try: with open(filename) as file: plain, cypher = file.read().split('\n') return plain, cypher except: with open(filename, 'w') as file: file.write(BACKUP) def save_key(filename, encode_map): "Dumps the map into two buffers and saves them to the key file." plain = cypher = str() for p, c in encode_map.items(): plain += p cypher += c with open(filename, 'w') as file: file.write(plain + '\n' + cypher) ################################################################################ def encode(encode_map, decode_map): "Encodes message for the user." print('Enter your message to encode (EOF when finished).') message = get_message() for char in message: sys.stdout.write(encode_map[char] if char in encode_map else char) def decode(encode_map, decode_map): "Decodes message for the user." print('Enter your message to decode (EOF when finished).') message = get_message() for char in message: sys.stdout.write(decode_map[char] if char in decode_map else char) def custom(encode_map, decode_map): "Allows user to edit the encoding/decoding dictionaries." plain, cypher = get_new_mapping() for p, c in zip(plain, cypher): encode_map[p] = c decode_map[c] = p ################################################################################ def get_message(): "Gets and returns text entered by the user (until EOF)." buffer = [] while True: line = sys.stdin.readline() if line: buffer.append(line) else: return ''.join(buffer) def get_new_mapping(): "Prompts for strings to edit encoding/decoding maps." while True: plain = get_unique_chars('What do you want to encode from?') cypher = get_unique_chars('What do you want to encode to?') if len(plain) == len(cypher): return plain, cypher print('Both lines should have the same length.') def get_unique_chars(prompt): "Gets strings that only contain unique characters." print(prompt) while True: line = input() if len(line) == len(set(line)): return line print('There were duplicate characters: please try again.') ################################################################################ # This map is used for dispatching commands in the interface loop. FUNC = {'1': encode, '2': decode, '3': custom, '4': lambda a, b: sys.exit()} ################################################################################ if __name__ == '__main__': main() For all those Python programmers out there, your help is being requested. How should the formatting (not necessarily the coding by altered to fit Python's style guide? My friend does not need to be learning things that are not correct. If you have suggestions on the code, feel free to post them to this wiki as well.

Read the article
Javascript Closures - What are the negatives?

- by vol7ron

Question: There seem to be many benefits to Closures, but what are the negatives (memory leakage? obfuscation problems? bandwidth increasage?)? Additionally, is my understanding of Closures correct? Finally, once closures are created, can they be destroyed? I've been reading a little bit about Javascript Closures. I hope someone a little more knowledgeable will guide my assertions, correcting me where wrong. Benefits of Closures: Encapsulate the variables to a local scope, by using an internal function. The anonymity of the function is insignificant. What I've found helpful is to do some basic testing, regarding local/global scope: <script type="text/javascript"> var global_text = ""; var global_count = 0; var global_num1 = 10; var global_num2 = 20; var global_num3 = 30; function outerFunc() { var local_count = local_count || 0; alert("global_num1: " + global_num1); // global_num1: undefined var global_num1 = global_num1 || 0; alert("global_num1: " + global_num1); // global_num1: 0 alert("global_num2: " + global_num2); // global_num2: 20 global_num2 = global_num2 || 0; // (notice) no definition with 'var' alert("global_num2: " + global_num2); // global_num2: 20 global_num2 = 0; alert("local_count: " + local_count); // local_count: 0 function output() { global_num3++; alert("local_count: " + local_count + "\n" + "global_count: " + global_count + "\n" + "global_text: " + global_text ); local_count++; } local_count++; global_count++; return output; } var myFunc = outerFunc(); myFunc(); /* Outputs: ********************** * local_count: 1 * global_count: 1 * global_text: **********************/ global_text = "global"; myFunc(); /* Outputs: ********************** * local_count: 2 * global_count: 1 * global_text: global **********************/ var local_count = 100; myFunc(); /* Outputs: ********************** * local_count: 3 * global_count: 1 * global_text: global **********************/ alert("global_num1: " + global_num1); // global_num1: 10 alert("global_num2: " + global_num2); // global_num2: 0 alert("global_num3: " + global_num3); // global_num3: 33 </script> Interesting things I took out of it: The alerts in outerFunc are only called once, which is when the outerFunc call is assigned to myFunc (myFunc = outerFunc()). This assignment seems to keep the outerFunc open, in what I would like to call a persistent state. Everytime myFunc is called, the return is executed. In this case, the return is the internal function. Something really interesting is the localization that occurs when defining local variables. Notice the difference in the first alert between global_num1 and global_num2, even before the variable is trying to be created, global_num1 is considered undefined because the 'var' was used to signify a local variable to that function. -- This has been talked about before, in the order of operation for the Javascript engine, it's just nice to see this put to work. Globals can still be used, but local variables will override them. Notice before the third myFunc call, a global variable called local_count is created, but it as no effect on the internal function, which has a variable that goes by the same name. Conversely, each function call has the ability to modify global variables, as noticed by global_var3. Post Thoughts: Even though the code is straightforward, it is cluttered by alerts for you guys, so you can plug and play. I know there are other examples of closures, many of which use anonymous functions in combination with looping structures, but I think this is good for a 101-starter course to see the effects. The one thing I'm concerned with is the negative impact closures will have on memory. Because it keeps the function environment open, it is also keeping those variables stored in memory, which may/may not have performance implications, especially regarding DOM traversals and garbage collection. I'm also not sure what kind of role this will play in terms of memory leakage and I'm not sure if the closure can be removed from memory by a simple "delete myFunc;." Hope this helps someone, vol7ron

Read the article
Bad disks in ancient server

- by Joel Coel

I have a 1998-era Netware 3.12 server that runs everything on our campus: general ledger, purchasing, payroll, student information, grades, you name it. The server has an Adaptec RAID controller with two volumes: RAID 1, 2 17GB scsi disks, Seagate ST318417W RAID 5, 3 4GB scsi disks, 2 Seagate ST34573W and 1 ST34572W. We are currently in the early stages of a project to replace this system, but you don't just jump into a new system like that and so I need to keep this server running until at least November 2011. This week we had not one but two hard drives fail. Thankfully they are from different volumes and we're able to keep running for the moment, but given the close nature of these failures I have serious doubts that I'll be able to avoid catastrophic failure from this server through the November target as is without restoring the RAID redundancy — it'll only take one more drive failure anywhere and I'm completely hosed. We are fortunate enough to have exact match "spares" lying around for both drives, but the spares are in unknown condition. I tried swapping just them in, but the RAID controller isn't smart enough to handle this and it renders the system unbootable. As for the RAID controller itself, there is utility I can get into during POST via a Ctrl-A shortcut, but I can't do much useful from there. To actually manage volumes I must first boot in to Netware, at which point I can use CI/O Array Management Software Version 2.0 to actually look at volume information. I suspect that the normal way to manage things is to boot from a special floppy with the controller software on it, but that floppy is long gone. Going through the options in the RAID software, I think the only supported way to replace a disk in an existing RAID volume is to physically add the disk, boot up and configure it as a "spare" for a volume, force the volume to use the spare to replace an existing down disk (and at this point I'm only guessing) so that the down disk becomes the spare, repair the volume, remove the spare from the volume, and then shut down and remove the disk. Then start all over for the other failed disk. All this amounts to a lot of downtime, assuming I can even make it work and that my spares are any good. As for finding reliable spares, I have no clue where to even begin looking to find a new 4GB scsi drive, or even which exact scsi system I'm looking for, as it's gone through a few different iterations over time. Another option is to migrate this to a virtual machine (hyper-v), but all previous attempts we've made in this area have failed to get very far. When this machine was installed I was just graduating from high school, and so it requires lower level knowledge of netware and dos than I ever developed, or if I did have since forgotten (I'm not exactly a dos neophyte, either). Part of my problem is this is a high-use server, and taking it down for a few days to figure things out isn't gonna fly very well. As for the question, I'm looking for anything that might be helpful in this situation: a recommendation on a place to find good spares from this era, personal experience repairing RAID volumes using a similar controller or building a hyper-v vm from an old netware server, a line on a floppy with better software for the RAID controller, recommendation on a good Novell consultant in Nebraska that would be able to put things right, a whole other option I haven't considered yet, etc. Update: For backups, we have good (recently verified via restore) backups of the data only -- nothing for the software that actually runs things. Update 2: Just a progress report that I currently have a working Netware 3.12 install in VMWare Virtual Server 2.0, thanks largely to the guide I found here: http://cerbulescubogdan.blogspot.com/2010/11/novell-netware-312-on-vmware.html The next steps are preparing empty netware volumes to match the additional volumes on my existing server, taking a dump of everything on the C:\ drive and netware volumes on my existing server, and figuring out from that information what modules need added to netware, installing my licenses (we do still have that disk, if it's any good), and moving data over. I have approval to bring the server down for a week after the first of the year (sadly not before), so, aside from creating empty volumes, the rest of the work will have to wait until then. Final Update (Jan 5, 2011): I was able to get spares working in both raid arrays without data loss this week. Both are now listed by the controller as "FAULT TOLLERANT" (yay!). I was also able to build on the progress from my last update and now have a functional "spare" server in VMWare Server 2.0. The spare can run and use our erp software, but I can't put it into production because I can't (yet) print from that box (and I have no idea why). Even so, this VM will do in a pinch if I have no other choice, and between it and the repaired RAID arrays I'm comfortable pushing on until I can junk the machine in November.

Read the article
Where do I start ?

- by Panthe

Brief History: Just graduated high school, learned a bit of python and C++, have no friends with any helpful computer knowledge at all. Out of anyone i met in my school years I was probably the biggest nerd, but no one really knew. I consider my self to have a vast amount of knowledge on computers and tech then the average person. built/fixed tons of computers, and ability to troubleshoot pretty much any problem I came across. Now that high school is over, Ive really been thinking about my career. Loving, living computers for the past 15 years of my life I decided to take my ability's and try to learn computer programming, why I didn't start earlier I don't know, seems to be big mistake on my part... Doing some research I concluded that Python was the first programming language I should learn, since it was high level and easier to understand then C++ and Java. I also knew that to become good at what I did I needed to know more then just 2 or 3 languages, which didn't seem like a big problem considering once I learned the way Python worked, mainly syntax changed, and the rest would come naturally. I watched a couple of youtube videos, downloaded some book pdf's and snooped around from some tutorials here and there to get the hang of what to do. A two solid weeks had passed of trying to understand the syntax, create small programs that used the basic functions and understanding how it worked, I think i have got the hang of it. It breaks down into what ive been dealing with all this time (although i kinda knew) is that, input,output, loops, functions and other things derived from 0's and 1's storing data and recalling it, ect. (A VERY BASIC IDEA). Ive been able to create small programs, Hangman, file storing, temperature conversion, Caeser Cipher decode/encoding, Fibonacci Sequence and more, which i can create and understand how each work. Being 2 weeks into this, I have learned alot. Nothing at all compared to what i should be learning in the years to come if i get a grip on what I'm doing. While doing these programs I wont stop untill I've done doing a practice problem on a book, which embarresing enough will take me a couple hour depending on the complexity of it. I absolutly will not put aside the challenge until its complete, WHICH CAN BE EXTREMELY DRAINING, ive tried most problems without cheating and reached success, which makes me feel extremely proud of my self after completing something after much trial and error. After all this I have met the demon, alogrithm's which seem to be key to effiecent code. I cant seem to rap my head around some of the computer codes people put out there using numbers, and sometimes even basic functions, I have been able to understand them after a while but i know there are alot more complex things to come, considering my self smart, functions that require complex codes, actually hurt my brain. NOTHING EVER IN LIFE HURT MY BRAIN....... not even math classes in highschool, trying to understand some of the stuff people put out there makes me feel like i have a mental disadvantage lol... i still walk forward though, crossing my fingers that the understanding will come with time. Sorry if is this is long i just wish someone takes all these things into consideration when answering my question. even through all these downsides im still pushing through and continuing to try and get good at this, i know reading these tutorials wont make me any good unless i can become creative and make my own, understand other peoples programs, so this leads me to the simple question i could have asked in the beginning..... WHERE IN THE WORLD DO I START ? Ive been trying to find out how to understand some of the open source projects, how i can work with experianced coders to learn from them and help them, but i dont think thats even possible by the way how far people's knowledge is compared to me, i have no freinds who i can learn from, can someone help me and guide me into the right direction.. i have a huge motivation to get good at coding, anything information would be extremely helpful

Read the article
Ajax and using responseXML

- by Banderdash

Hello, I have a XML file that looks like this: <response> <library name="My Library"> <book id="1" checked-out="1"> <authors> <author>David Flanagan</author> </authors> <title>JavaScript: The Definitive Guide</title> <isbn-10>0596101996</isbn-10> </book> <book id="2" checked-out="1"> <authors> <author>John Resig</author> </authors> <title>Pro JavaScript Techniques (Pro)</title> <isbn-10>1590597273</isbn-10> </book> <book id="3" checked-out="0"> <authors> <author>Erich Gamma</author> <author>Richard Helm</author> <author>Ralph Johnson</author> <author>John M. Vlissides</author> </authors> <title>Design Patterns: Elements of Reusable Object-Oriented Software</title> <isbn-10>0201633612</isbn-10> </book> ... </library> </response> I'm using a simple JS script to, on click show all the titles of the books: <script type="text/javascript"> function loadXMLDoc() { if (window.XMLHttpRequest) {// code for IE7+, Firefox, Chrome, Opera, Safari xmlhttp=new XMLHttpRequest(); } else {// code for IE6, IE5 xmlhttp=new ActiveXObject("Microsoft.XMLHTTP"); } xmlhttp.onreadystatechange=function() { if (xmlhttp.readyState==4 && xmlhttp.status==200) { xmlDoc=xmlhttp.responseXML; var txt=""; x=xmlDoc.getElementsByTagName("title"); for (i=0;i<x.length;i++) { txt=txt + x[i].childNodes[0].nodeValue + "<br />"; } document.getElementById("checkedIn").innerHTML=txt; } } xmlhttp.open("GET","ajax-response-data.xml",true); xmlhttp.send(); } </script> This works fine, as you can see here: http://clients.pixelbleed.net/ajax-test/ What I'd like to do is have the results post, on page load (not on click) into two separate DIV's depending on checked-out variable in the XML. So <book id="#" checked-out="1"> would post to the checkedIn div, <book id="#" checked-out="0"> posts to a checkedOut div. Also want to display the title and the author--would love any ideas as best method for accomplishing this. Apologize in advanced for the newbieness of my query.

Read the article
background image disappears when position relative used in firefox

- by toomanyairmiles

So I'm trying to add a badge to the top right corner of a site I'm doing some work on. z-index works to float the object above the page content but each time i try to use position relative the background image disappears only position absolute shows the image. I don't really want to use absolute as the image needs to be positioned on the right hand side of the sites menu bar not the right hand side of the viewport. Any thoughts or advice appreciated <div class="badge-box"> <a href="http://www.google.com" class="badge">Book Now!</a> </div> <div id="header"> <a href="index.php"><img src="images/pixel.gif" width="378" height="31" alt="Welcome to Gwynfryn Farm Cottages" /></a> </div> <div id="main-menu"> <div> <a href="/">Home</a> <a href="/cottages.php">Our Cottages</a> <a href="/gwynfryn.php">Bed & Breakfast</a> <a href="/rates.php">Price Guide</a> <a href="/llanbedr.php">Location & Local Attractions</a> <a href="/news.php">News & Special Offers</a> <a href="/contact.php">Contact Us</a> </div> </div> .badge-box { width: 1030px; margin-left: auto; margin-right: auto; border: 0px solid red; } .badge { background: url(../images/badge.png) 0px 0px no-repeat; width: 148px; height: 148px; text-indent: -10000px; position: relative; z-index: 999; } #header { width: 960px; height: 40px; margin-left:auto; margin-right:auto; margin-top:20px; padding: 20px 0px 0px 20px; background: #58564f url(../images/header-top-background.png); } #main-menu { width: 980px; margin-left: auto; margin-right: auto; height: 35px; /*background: red;*/ background: #58564f url(../images/header-bottom-background.png); font-family: Georgia, "Times New Roman", Times, serif; } #main-menu div { width: 776px; height: 35px; margin-left: auto; margin-right: auto; background: blue; } #main-menu div a { display: block; float: left; padding: 5px 10px 0px 10px; height: 30px; color: #FFFFFF; font-size: 1.2em; text-align: center; background: green; } #main-menu div a:hover { background-color: #333333; }

Read the article
evaluating cost/benefits of using extension methods in C# => 3.0

- by BillW

Hi, In what circumstances (usage scenarios) would you choose to write an extension rather than sub-classing an object ? < full disclosure : I am not an MS employee; I do not know Mitsu Furota personally; I do know the author of the open-source Componax library mentioned here, but I have no business dealings with him whatsoever; I am not creating, or planning to create any commercial product using extensions : in sum : this post is from pure intellectal curiousity related to my trying to (continually) become aware of "best practices" I find the idea of extension methods "cool," and obviously you can do "far-out" things with them as in the many examples you can in Mitsu Furota's (MS) blog postslink text. A personal friend wrote the open-source Componax librarylink text, and there's some remarkable facilities in there; but he is in complete command of his small company with total control over code guidelines, and every line of code "passes through his hands." While this is speculation on my part : I think/guess other issues might come into play in a medium-to-large software team situation re use of Extensions. Looking at MS's guidelines at link text, you find : In general, you will probably be calling extension methods far more often than implementing your own. ... In general, we recommend that you implement extension methods sparingly and only when you have to. Whenever possible, client code that must extend an existing type should do so by creating a new type derived from the existing type. For more information, see Inheritance (C# Programming Guide). ... When the compiler encounters a method invocation, it first looks for a match in the type's instance methods. If no match is found, it will search for any extension methods that are defined for the type, and bind to the first extension method that it finds. And at Ms's link text : Extension methods present no specific security vulnerabilities. They can never be used to impersonate existing methods on a type, because all name collisions are resolved in favor of the instance or static method defined by the type itself. Extension methods cannot access any private data in the extended class. Factors that seem obvious to me would include : I assume you would not write an extension unless you expected it be used very generally and very frequently. On the other hand : couldn't you say the same thing about sub-classing ? Knowing we can compile them into a seperate dll, and add the compiled dll, and reference it, and then use the extensions : is "cool," but does that "balance out" the cost inherent in the compiler first having to check to see if instance methods are defined as described above. Or the cost, in case of a "name clash," of using the Static invocation methods to make sure your extension is invoked rather than the instance definition ? How frequent use of Extensions would affect run-time performance or memory use : I have no idea. So, I'd appreciate your thoughts, or knowing about how/when you do, or don't do, use Extensions, compared to sub-classing. thanks, Bill

Read the article
How do I get my snapshots in Nexus to appear in the m2eclipse dependency search?

- by Brabster

Hi, I've been working through the Nexus guide this weekend and I've got everything set up, to the point that I can publish a snapshot to my local nexus install. I can't seem to work out how to get m2eclipse to see the snapshot and offer it as an option in the Add Dependencies search panel. How do I do that? Thanks! In case it's of any use, my settings.xml is as follows: <settings xmlns="http://maven.apache.org/SETTINGS/1.0.0" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://maven.apache.org/SETTINGS/1.0.0 http://maven.apache.org/xsd/settings-1.0.0.xsd"> <localRepository /> <interactiveMode /> <usePluginRegistry /> <offline /> <pluginGroups /> <servers> <server> <id>localSnap</id> <username>deployment</username> <password>*****</password> </server> </servers> <mirrors> <mirror>  <id>nexus</id> <mirrorOf>*</mirrorOf> <url>http://localhost:8080/nexus/content/groups/public</url> </mirror> </mirrors> <profiles> <profile> <id>nexus</id>   <repositories> <repository> <id>central</id> <url>http://central</url> <releases> <enabled>true</enabled> </releases> <snapshots> <enabled>true</enabled> </snapshots> </repository> </repositories> <pluginRepositories> <pluginRepository> <id>central</id> <url>http://central</url> <releases> <enabled>true</enabled> </releases> <snapshots> <enabled>true</enabled> </snapshots> </pluginRepository> </pluginRepositories> </profile> </profiles> <activeProfiles>  <activeProfile>nexus</activeProfile> </activeProfiles> </settings>

Read the article
Anything wrong with this function for comparing floats?

- by Michael Borgwardt

When my Floating-Point Guide was yesterday published on slashdot, I got a lot of flak for my suggested comparison function, which was indeed inadequate. So I finally did the sensible thing and wrote a test suite to see whether I could get them all to pass. Here is my result so far. And I wonder if this is really as good as one can get with a generic (i.e. not application specific) float comparison function, or whether I still missed some edge cases. import static org.junit.Assert.assertFalse; import static org.junit.Assert.assertTrue; import org.junit.Test; public class NearlyEqualsTest { public static boolean nearlyEqual(float a, float b) { final float epsilon = 0.000001f; final float absA = Math.abs(a); final float absB = Math.abs(b); final float diff = Math.abs(a-b); if (a*b==0) { // a or b or both are zero // relative error is not meaningful here return diff < Float.MIN_VALUE / epsilon; } else { // use relative error return diff / (absA+absB) < epsilon; } } /** Regular large numbers - generally not problematic */ @Test public void big() { assertTrue(nearlyEqual(1000000f, 1000001f)); assertTrue(nearlyEqual(1000001f, 1000000f)); assertFalse(nearlyEqual(10000f, 10001f)); assertFalse(nearlyEqual(10001f, 10000f)); } /** Negative large numbers */ @Test public void bigNeg() { assertTrue(nearlyEqual(-1000000f, -1000001f)); assertTrue(nearlyEqual(-1000001f, -1000000f)); assertFalse(nearlyEqual(-10000f, -10001f)); assertFalse(nearlyEqual(-10001f, -10000f)); } /** Numbers around 1 */ @Test public void mid() { assertTrue(nearlyEqual(1.0000001f, 1.0000002f)); assertTrue(nearlyEqual(1.0000002f, 1.0000001f)); assertFalse(nearlyEqual(1.0002f, 1.0001f)); assertFalse(nearlyEqual(1.0001f, 1.0002f)); } /** Numbers around -1 */ @Test public void midNeg() { assertTrue(nearlyEqual(-1.000001f, -1.000002f)); assertTrue(nearlyEqual(-1.000002f, -1.000001f)); assertFalse(nearlyEqual(-1.0001f, -1.0002f)); assertFalse(nearlyEqual(-1.0002f, -1.0001f)); } /** Numbers between 1 and 0 */ @Test public void small() { assertTrue(nearlyEqual(0.000000001000001f, 0.000000001000002f)); assertTrue(nearlyEqual(0.000000001000002f, 0.000000001000001f)); assertFalse(nearlyEqual(0.000000000001002f, 0.000000000001001f)); assertFalse(nearlyEqual(0.000000000001001f, 0.000000000001002f)); } /** Numbers between -1 and 0 */ @Test public void smallNeg() { assertTrue(nearlyEqual(-0.000000001000001f, -0.000000001000002f)); assertTrue(nearlyEqual(-0.000000001000002f, -0.000000001000001f)); assertFalse(nearlyEqual(-0.000000000001002f, -0.000000000001001f)); assertFalse(nearlyEqual(-0.000000000001001f, -0.000000000001002f)); } /** Comparisons involving zero */ @Test public void zero() { assertTrue(nearlyEqual(0.0f, 0.0f)); assertFalse(nearlyEqual(0.00000001f, 0.0f)); assertFalse(nearlyEqual(0.0f, 0.00000001f)); } /** Comparisons of numbers on opposite sides of 0 */ @Test public void opposite() { assertFalse(nearlyEqual(1.000000001f, -1.0f)); assertFalse(nearlyEqual(-1.0f, 1.000000001f)); assertFalse(nearlyEqual(-1.000000001f, 1.0f)); assertFalse(nearlyEqual(1.0f, -1.000000001f)); assertTrue(nearlyEqual(10000f*Float.MIN_VALUE, -10000f*Float.MIN_VALUE)); } /** * The really tricky part - comparisons of numbers * very close to zero. */ @Test public void ulp() { assertTrue(nearlyEqual(Float.MIN_VALUE, -Float.MIN_VALUE)); assertTrue(nearlyEqual(-Float.MIN_VALUE, Float.MIN_VALUE)); assertTrue(nearlyEqual(Float.MIN_VALUE, 0)); assertTrue(nearlyEqual(0, Float.MIN_VALUE)); assertTrue(nearlyEqual(-Float.MIN_VALUE, 0)); assertTrue(nearlyEqual(0, -Float.MIN_VALUE)); assertFalse(nearlyEqual(0.000000001f, -Float.MIN_VALUE)); assertFalse(nearlyEqual(0.000000001f, Float.MIN_VALUE)); assertFalse(nearlyEqual(Float.MIN_VALUE, 0.000000001f)); assertFalse(nearlyEqual(-Float.MIN_VALUE, 0.000000001f)); assertFalse(nearlyEqual(1e20f*Float.MIN_VALUE, 0.0f)); assertFalse(nearlyEqual(0.0f, 1e20f*Float.MIN_VALUE)); assertFalse(nearlyEqual(1e20f*Float.MIN_VALUE, -1e20f*Float.MIN_VALUE)); } }

Read the article
Looking for best practise for writing a serial device communication app in C#

- by cdotlister

I am pretty new to serial comms, but would like advise on how to best achieve a robust application which speak to and listens to a serial device. I have managed to make use of System.IO.serialport, and successfully connected to, sent data to and recieved from my device. The way things work is this. My application connects to the Com Port and opens the port.... I then connect my device to the com port, and it detects a connectio to the PC, so sends a bit of text. it's really just copyright info, as well as the version of the firmware. I don't do anything with that, except display it in my 'activity' window. The device then waits. I can then query information, but sending a command such as 'QUERY PARAMETER1'. It then replies with something like: 'QUERY PARAMETER1\r\n\r\n76767\r\n\r\n' I then process that. I can then update it by sending 'SET PARAMETER1 12345', and it will reply with 'QUERY PARAMETER1\r\n\r\n12345\r\n\r\n'. All pretty basic. So, what I have done is created a Communication Class. this call is called in it's own thread, and sends data back to the main form... and also allows me to send messages to it. Sending data is easy. Recieving is a bit more tricky. I have employed the use of the datarecieved event, and when ever data comes in, I echo that to my screen. My problem is this: When I send a command, I feel I am being very dodgy in my handling. What I am doing is, lets say I am sending 'QUERY PARAMETER1'. I send the command to the device, I then put 'PARAMETER1' into a global variable, and I do a Thread.Sleep(100). On the data recieved, I then have a bit of logic that checks the incoming data, and sees if the string CONTAINS the value in the gloabl variable. As the reply may be 'QUERY PARAMETER1\r\n\r\n76767\r\n\r\n', it sees that it contains my parameter, parses the string, and returns the value I am looking for, but placing it into another global variable. My sending method was sleeping for 100ms. It then wakes, and checks the returned global variable. If it has data... then I'm happy, and I process the data. Problem is... if the sleep is too short.. it will fail. And I feel it's flakey.. putting stuff into variables.. then waiting... The other option is to use ReadLine instead, but that's very blocking. So I remove the datarecieved method, and instead... just send the data... then call ReadLine(). That may give me better results. There's no time, except when we connect initially, that data comes from the device, without me requesting it. So, maybe readline will be simpler and safer? Is this known as 'Blocking' reads? Also, can I set a timeout? Hopefully someone can guide me.

Read the article

Search Results

Search found 5278 results on 212 pages for 'hitchhikers guide to the galaxy'.

Page 202/212 | < Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209 | Next Page >

- by Lekensteyn

- by Tom Brito

- by Hristo

- by user287745

- by Babul

- by Ian Boyd

- by robmzd

- by new

- by Ziv

- by Praveen Chandrasekaran

- by Praveen Chandrasekaran

- by Fitzroy

- by Shailesh Jaiswal

- by DownUnder

- by Noctis Skytower

- by Noctis Skytower

- by vol7ron

- by Joel Coel

- by Panthe

- by Banderdash

- by toomanyairmiles

- by BillW

- by Brabster

- by Michael Borgwardt

- by cdotlister

< Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209 | Next Page >