Search Results

Search found 5349 results on 214 pages for 'narf the mouse'.

Page 202/214 | < Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >

• Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

  - by jgottula

  I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

  Read the article

• "LNK2001: unresolved external symbol" when trying to build my program

  - by random

  I get the following error(s) on my program that captures the mouse and then draws a line. Errors: 1>------ Build started: Project: Capture_Mouse_Line, Configuration: Debug Win32 ------ 1> main.cpp 1>main.obj : error LNK2001: unresolved external symbol "public: static long * Line::yc2" (?yc2@Line@@2PAJA) 1>main.obj : error LNK2001: unresolved external symbol "public: static long * Line::xc2" (?xc2@Line@@2PAJA) 1>main.obj : error LNK2001: unresolved external symbol "public: static long * Line::yc1" (?yc1@Line@@2PAJA) 1>main.obj : error LNK2001: unresolved external symbol "public: static long * Line::xc1" (?xc1@Line@@2PAJA) 1>MSVCRTD.lib(crtexe.obj) : error LNK2019: unresolved external symbol _main referenced in function ___tmainCRTStartup 1>D:\Visual C++ Projects\Capture_Mouse_Line\Debug\Capture_Mouse_Line.exe : fatal error LNK1120: 5 unresolved externals ========== Build: 0 succeeded, 1 failed, 0 up-to-date, 0 skipped ========== Here is my code: #include<allegro5\allegro.h> #include<allegro5\allegro_native_dialog.h> #include<allegro5\allegro_primitives.h> #include<Windows.h> #include<allegro5\allegro_windows.h> #ifndef WIDTH #define WIDTH 1440 #endif #ifndef HEIGHT #define HEIGHT 900 #endif class Line { public: static void ErasePreviousLine(); static void DrawLine(long* x, long* y,long* x2,long* y2); static bool Erasable(); static long* xc1; static long* yc1; static long* xc2; static long* yc2; }; void Line::ErasePreviousLine() { delete xc1; xc1 = NULL; delete yc1; yc1 = NULL; delete xc2; xc2 = NULL; delete yc2; yc2 = NULL; } bool Line::Erasable() { if(xc1 && yc1 && xc2 && yc2 == NULL) { return false; } else { return true; } } void Line::DrawLine(long* x,long* y,long* x2,long* y2) { if(!al_init_primitives_addon()) { al_show_native_message_box(NULL,NULL,NULL,"failed to initialize allegro", NULL,NULL); } xc1 = x; yc1 = y; xc2 = x2; yc2 = y2; al_draw_line((float)*xc1, (float)*yc1, (float)*xc2, (float)*yc2,al_map_rgb(255,0,255), 1); delete x; delete y; delete x2; delete y2; } LRESULT CALLBACK WndProc(HWND hwnd, UINT msg, WPARAM wParam, LPARAM lParam); int WINAPI WinMain(HINSTANCE hInstance,HINSTANCE hPrevInstance, LPSTR lpCmdLine, int nCmdShow) { MSG msg; ALLEGRO_DISPLAY* display = NULL; if(!al_init()) { al_show_native_message_box(NULL,NULL,NULL,"failed to initialize allegro", NULL,NULL); return -1; } display = al_create_display(WIDTH,HEIGHT); if(!display) { al_show_native_message_box(NULL,NULL,NULL,"failed to initialize display", NULL,NULL); return -1; } HWND hwnd = al_get_win_window_handle(display); if(hwnd == NULL) { MessageBox(NULL, "Window Creation Failed!", "Error!", MB_ICONEXCLAMATION | MB_OK); return 0; } ShowWindow(hwnd, nCmdShow); UpdateWindow(hwnd); while(GetMessage(&msg, NULL, 0, 0) > 0) { TranslateMessage(&msg); DispatchMessage(&msg); } return msg.wParam; } LRESULT CALLBACK WndProc(HWND hwnd, UINT msg, WPARAM wParam, LPARAM lParam) { static bool bIsCaptured; static POINTS ptsBegin; static POINTS ptsEnd; switch(msg) { case WM_LBUTTONDOWN: SetCapture(hwnd); bIsCaptured = true; ptsBegin = MAKEPOINTS(lParam); return 0; case WM_MOUSEMOVE: if(wParam & MK_LBUTTON) { if(!Line::Erasable()) { return 0; } Line::ErasePreviousLine(); ptsEnd = MAKEPOINTS(lParam); Line::DrawLine(new long(ptsBegin.x),new long(ptsBegin.y),new long(ptsEnd.x),new long(ptsEnd.y)); } break; case WM_LBUTTONUP: bIsCaptured = false; ReleaseCapture(); break; case WM_ACTIVATEAPP: { if(wParam == TRUE) { if(bIsCaptured){ SetCapture(hwnd);} } } break; } return 0; }

  Read the article

• Increasing efficiency of N-Body gravity simulation

  - by Postman

  I'm making a space exploration type game, it will have many planets and other objects that will all have realistic gravity. I currently have a system in place that works, but if the number of planets goes above 70, the FPS decreases an practically exponential rates. I'm making it in C# and XNA. My guess is that I should be able to do gravity calculations between 100 objects without this kind of strain, so clearly my method is not as efficient as it should be. I have two files, Gravity.cs and EntityEngine.cs. Gravity manages JUST the gravity calculations, EntityEngine creates an instance of Gravity and runs it, along with other entity related methods. EntityEngine.cs public void Update() { foreach (KeyValuePair<string, Entity> e in Entities) { e.Value.Update(); } gravity.Update(); } (Only relevant piece of code from EntityEngine, self explanatory. When an instance of Gravity is made in entityEngine, it passes itself (this) into it, so that gravity can have access to entityEngine.Entities (a dictionary of all planet objects)) Gravity.cs namespace ExplorationEngine { public class Gravity { private EntityEngine entityEngine; private Vector2 Force; private Vector2 VecForce; private float distance; private float mult; public Gravity(EntityEngine e) { entityEngine = e; } public void Update() { //First loop foreach (KeyValuePair<string, Entity> e in entityEngine.Entities) { //Reset the force vector Force = new Vector2(); //Second loop foreach (KeyValuePair<string, Entity> e2 in entityEngine.Entities) { //Make sure the second value is not the current value from the first loop if (e2.Value != e.Value ) { //Find the distance between the two objects. Because Fg = G * ((M1 * M2) / r^2), using Vector2.Distance() and then squaring it //is pointless and inefficient because distance uses a sqrt, squaring the result simple cancels that sqrt. distance = Vector2.DistanceSquared(e2.Value.Position, e.Value.Position); //This makes sure that two planets do not attract eachother if they are touching, completely unnecessary when I add collision, //For now it just makes it so that the planets are not glitchy, performance is not significantly improved by removing this IF if (Math.Sqrt(distance) > (e.Value.Texture.Width / 2 + e2.Value.Texture.Width / 2)) { //Calculate the magnitude of Fg (I'm using my own gravitational constant (G) for the sake of time (I know it's 1 at the moment, but I've been changing it) mult = 1.0f * ((e.Value.Mass * e2.Value.Mass) / distance); //Calculate the direction of the force, simply subtracting the positions and normalizing works, this fixes diagonal vectors //from having a larger value, and basically makes VecForce a direction. VecForce = e2.Value.Position - e.Value.Position; VecForce.Normalize(); //Add the vector for each planet in the second loop to a force var. Force = Vector2.Add(Force, VecForce * mult); //I have tried Force += VecForce * mult, and have not noticed much of an increase in speed. } } } //Add that force to the first loop's planet's position (later on I'll instead add to acceleration, to account for inertia) e.Value.Position += Force; } } } } I have used various tips (about gravity optimizing, not threading) from THIS question (that I made yesterday). I've made this gravity method (Gravity.Update) as efficient as I know how to make it. This O(N^2) algorithm still seems to be eating up all of my CPU power though. Here is a LINK (google drive, go to File download, keep .Exe with the content folder, you will need XNA Framework 4.0 Redist. if you don't already have it) to the current version of my game. Left click makes a planet, right click removes the last planet. Mouse moves the camera, scroll wheel zooms in and out. Watch the FPS and Planet Count to see what I mean about performance issues past 70 planets. (ALL 70 planets must be moving, I've had 100 stationary planets and only 5 or so moving ones while still having 300 fps, the issue arises when 70+ are moving around) After 70 planets are made, performance tanks exponentially. With < 70 planets, I get 330 fps (I have it capped at 300). At 90 planets, the FPS is about 2, more than that and it sticks around at 0 FPS. Strangely enough, when all planets are stationary, the FPS climbs back up to around 300, but as soon as something moves, it goes right back down to what it was, I have no systems in place to make this happen, it just does. I considered multithreading, but that previous question I asked taught me a thing or two, and I see now that that's not a viable option. I've also thought maybe I could do the calculations on my GPU instead, though I don't think it should be necessary. I also do not know how to do this, it is not a simple concept and I want to avoid it unless someone knows a really noob friendly simple way to do it that will work for an n-body gravity calculation. (I have an NVidia gtx 660) Lastly I've considered using a quadtree type system. (Barnes Hut simulation) I've been told (in the previous question) that this is a good method that is commonly used, and it seems logical and straightforward, however the implementation is way over my head and I haven't found a good tutorial for C# yet that explains it in a way I can understand, or uses code I can eventually figure out. So my question is this: How can I make my gravity method more efficient, allowing me to use more than 100 objects (I can render 1000 planets with constant 300+ FPS without gravity calculations), and if I can't do much to improve performance (including some kind of quadtree system), could I use my GPU to do the calculations?

  Read the article

• Understanding implementation of glu.PickMatrix()

  - by stoney78us

  I am working on an OpenGL project which requires object selection feature. I use OpenTK framework to do this; however OpenTK doesn't support glu.PickMatrix() method to define the picking region. I ended up googling its implementation and here is what i got: void GluPickMatrix(double x, double y, double deltax, double deltay, int[] viewport) { if (deltax <= 0 || deltay <= 0) { return; } GL.Translate((viewport[2] - 2 * (x - viewport[0])) / deltax, (viewport[3] - 2 * (y - viewport[1])) / deltay, 0); GL.Scale(viewport[2] / deltax, viewport[3] / deltay, 1.0); } I totally fail to understand this piece of code. Moreover, this doesn't work with my following code sample: //selectbuffer private int[] _selectBuffer = new int[512]; private void Init() { float[] triangleVertices = new float[] { 0.0f, 1.0f, 0.0f, -1.0f, -1.0f, 0.0f, 1.0f, -1.0f, 0.0f }; float[] _triangleColors = new float[] { 0.0f, 1.0f, 0.0f, 1.0f, 0.0f, 0.0f, 0.0f, 0.0f, 1.0f }; GL.GenBuffers(2, _vBO); GL.BindBuffer(BufferTarget.ArrayBuffer, _vBO[0]); GL.BufferData(BufferTarget.ArrayBuffer, new IntPtr(sizeof(float) * _triangleVertices.Length), _triangleVertices, BufferUsageHint.StaticDraw); GL.VertexPointer(3, VertexPointerType.Float, 0, 0); GL.BindBuffer(BufferTarget.ArrayBuffer, _vBO[1]); GL.BufferData(BufferTarget.ArrayBuffer, new IntPtr(sizeof(float) * _triangleColors.Length), _triangleColors, BufferUsageHint.StaticDraw); GL.ColorPointer(3, ColorPointerType.Float, 0, 0); GL.EnableClientState(ArrayCap.VertexArray); GL.EnableClientState(ArrayCap.ColorArray); //Selectbuffer set up GL.SelectBuffer(512, _selectBuffer); } private void glControlWindow_Paint(object sender, PaintEventArgs e) { GL.Clear(ClearBufferMask.ColorBufferBit); GL.Clear(ClearBufferMask.DepthBufferBit); float[] eyes = { 0.0f, 0.0f, -10.0f }; float[] target = { 0.0f, 0.0f, 0.0f }; Matrix4 projection = Matrix4.CreatePerspectiveFieldOfView(0.785398163f, 4.0f / 3.0f, 0.1f, 100f); //45 degree = 0.785398163 rads Matrix4 view = Matrix4.LookAt(eyes[0], eyes[1], eyes[2], target[0], target[1], target[2], 0, 1, 0); Matrix4 model = Matrix4.Identity; Matrix4 MV = view * model; //First Clear Buffers GL.Clear(ClearBufferMask.ColorBufferBit); GL.Clear(ClearBufferMask.DepthBufferBit); GL.MatrixMode(MatrixMode.Projection); GL.LoadIdentity(); GL.LoadMatrix(ref projection); GL.MatrixMode(MatrixMode.Modelview); GL.LoadIdentity(); GL.LoadMatrix(ref MV); GL.Viewport(0, 0, glControlWindow.Width, glControlWindow.Height); GL.Enable(EnableCap.DepthTest); //Enable correct Z Drawings GL.DepthFunc(DepthFunction.Less); //Enable correct Z Drawings GL.MatrixMode(MatrixMode.Modelview); GL.PushMatrix(); GL.Translate(3.0f, 0.0f, 0.0f); DrawTriangle(); GL.PopMatrix(); GL.PushMatrix(); GL.Translate(-3.0f, 0.0f, 0.0f); DrawTriangle(); GL.PopMatrix(); //Finally... GraphicsContext.CurrentContext.VSync = true; //Caps frame rate as to not over run GPU glControlWindow.SwapBuffers(); //Takes from the 'GL' and puts into control } private void DrawTriangle() { GL.BindBuffer(BufferTarget.ArrayBuffer, _vBO[0]); GL.VertexPointer(3, VertexPointerType.Float, 0, 0); GL.EnableClientState(ArrayCap.VertexArray); GL.DrawArrays(BeginMode.Triangles, 0, 3); GL.DisableClientState(ArrayCap.VertexArray); } //mouse click event implementation private void glControlWindow_MouseClick(object sender, System.Windows.Forms.MouseEventArgs e) { //Enter Select mode. Pretend drawing. GL.RenderMode(RenderingMode.Select); int[] viewport = new int[4]; GL.GetInteger(GetPName.Viewport, viewport); GL.PushMatrix(); GL.MatrixMode(MatrixMode.Projection); GL.LoadIdentity(); GluPickMatrix(e.X, e.Y, 5, 5, viewport); Matrix4 projection = Matrix4.CreatePerspectiveFieldOfView(0.785398163f, 4.0f / 3.0f, 0.1f, 100f); // this projection matrix is the same as one in glControlWindow_Paint method. GL.LoadMatrix(ref projection); GL.MatrixMode(MatrixMode.Modelview); int i = 0; int hits; GL.PushMatrix(); GL.Translate(3.0f, 0.0f, 0.0f); GL.PushName(i); DrawTriangle(); GL.PopName(); GL.PopMatrix(); i++; GL.PushMatrix(); GL.Translate(-3.0f, 0.0f, 0.0f); GL.PushName(i); DrawTriangle(); GL.PopName(); GL.PopMatrix(); hits = GL.RenderMode(RenderingMode.Render); .....hits processing code goes here... GL.PopMatrix(); glControlWindow.Invalidate(); } I expect to get only one hit everytime i click inside a triangle, but i always get 2 no matter where i click. I suspect there is something wrong with the implementation of the GluPickMatrix, I haven't figured out yet.

  Read the article

• CSS hover behavior inconsistent on desktop/mobile devices [migrated]

  - by tbart

  I have a strange problem: This page looks good on desktop browsers, but the hovering effect does not seem to work correctly on at least my CM7 Android 2.3.7 device. I know hovering is not supposed to work on touch displays as it does with a mouse, but I'd like to have touch feedback, i.e. the highlight color should show once the user has tapped a menu item. This does work when the link is just a href="#" but it does not when it is a real link. I tried all sorts of stuff as you can see, to no avail. If you go back in the browser history after having tapped a real link, the item is highlighted, so the browser understands the CSS I am throwing at it. However, the javascript alert makes it clear that it only seems to interpret the link opening action and does not care about the color changing stuff. Weird that is. Workarounds welcome, preferable without javascript, but if it has to be JS, then go ahead! either go here: http://orpheus.co.at/hoverprob and Use the source, Luke! or see it here in all its glory: <html> <head> <meta name="viewport" content="width=320"> <style> #nav, #nav ul { width: 100%; float: left; list-style: none; line-height: 1; background: #fff; font-weight: bold; padding: 0; margin: 0 0 5px 0; } #nav a { display: block; color: #001834; text-decoration: none; padding: 5px 7px; } #nav li { float: left; padding: 0; width: 33%; } #nav li ul { position: absolute; left: -9999px; height: auto; margin: 0; opacity: .95; width: 100%; } #nav li a { text-align: center; height: 20px; line-height: 20px; } #nav li ul li a { text-align: left; } #nav li ul li { float: none; /* width: 316px; */ width: 100%; } #nav li:hover ul ul, #nav li:hover ul ul ul, #nav li.sfhover ul ul, #nav li.sfhover ul ul ul { left: -9999px; } #nav li:hover ul, #nav li li:hover ul, #nav li li li:hover ul, #nav li.sfhover ul, #nav li li.sfhover ul, #nav li li li.sfhover ul { left: 0; } #nav li.educate { background: #FFF0B8; /* background: #FF0000; */ /* border-radius: 5px; */ border: 5px; } #nav li.educate:hover { background: #FFCE00; /* border-radius: 5px; */ } </style> </head> <body> <div id="mobMenu"> <ul id="nav" class="nav"> <li class="educate"><a href="#">menu</a> <ul class="educate"> <li class="educate"><a href="#">href=&quot#&quot;, works</a></li> <!--(+emtpy onmouseover for iPose devices)--> <li class="educate"><a onmouseover="" href="index.html">does not work, real link</a></li> <li class="educate" id="bla"><a onmousedown="document.getElementById('bla').style.backgroundColor='Blue'; alert('Done');document.location='index.html';" href="#">JS, not interpreted in corr order</a></li> </ul> </li> </div> </body>

  Read the article

• Part 4 of 4 : Tips/Tricks for Silverlight Developers.

  - by mbcrump

  Part 1 | Part 2 | Part 3 | Part 4 I wanted to create a series of blog post that gets right to the point and is aimed specifically at Silverlight Developers. The most important things I want this series to answer is : What is it?  Why do I care? How do I do it? I hope that you enjoy this series. Let’s get started: Tip/Trick #16) What is it? Find out version information about Silverlight and which WebKit it is using by going to http://issilverlightinstalled.com/scriptverify/. Why do I care? I’ve had those users that its just easier to give them a site and say copy/paste the line that says User Agent in order to troubleshoot a Silverlight problem. I’ve also been debugging my own Silverlight applications and needed an easy way to determine if the plugin is disabled or not. How do I do it: Simply navigate to http://issilverlightinstalled.com/scriptverify/ and hit the Verify button. An example screenshot is located below: Results from Chrome 7 Results from Internet Explorer 8 (With Silverlight Disabled) Tip/Trick #17) What is it? Use Lambdas whenever you can. Why do I care?  It is my personal opinion that code is easier to read using Lambdas after you get past the syntax. How do I do it: For example: You may write code like the following: void MainPage_Loaded(object sender, RoutedEventArgs e) { //Check and see if we have a newer .XAP file on the server Application.Current.CheckAndDownloadUpdateAsync(); Application.Current.CheckAndDownloadUpdateCompleted += new CheckAndDownloadUpdateCompletedEventHandler(Current_CheckAndDownloadUpdateCompleted); } void Current_CheckAndDownloadUpdateCompleted(object sender, CheckAndDownloadUpdateCompletedEventArgs e) { if (e.UpdateAvailable) { MessageBox.Show( "An update has been installed. To see the updates please exit and restart the application"); } } To me this style forces me to look for the other Method to see what the code is actually doing. The style located below is much easier to read in my opinion and does the exact same thing. void MainPage_Loaded(object sender, RoutedEventArgs e) { //Check and see if we have a newer .XAP file on the server Application.Current.CheckAndDownloadUpdateAsync(); Application.Current.CheckAndDownloadUpdateCompleted += (s, e) => { if (e.UpdateAvailable) { MessageBox.Show( "An update has been installed. To see the updates please exit and restart the application"); } }; } Tip/Trick #18) What is it? Prevent development Web Service references from breaking when Visual Studio auto generates a new port number. Why do I care?  We have all been there, we are developing a Silverlight Application and all of a sudden our development web services break. We check and find out that the local port number that Visual Studio assigned has changed and now we need up to update all of our service references. We need a way to stop this. How do I do it: This can actually be prevented with just a few mouse click. Right click on your web solution and goto properties. Click the tab that says, Web. You just need to click the radio button and specify a port number. Now you won’t be bothered with that anymore. Tip/Trick #19) What is it? You can disable the Close Button a ChildWindow. Why do I care?  I wouldn’t blog about it if I hadn’t seen it. Devs trying to override keystrokes to prevent users from closing a Child Window. How do I do it: A property exist on the ChildWindow called “HasCloseButton”, you simply change that to false and your close button is gone. You can delete the “Cancel” button and add some logic to the OK button if you want the user to respond before proceeding. Tip/Trick #20) What is it? Cleanup your XAML. Why do I care?  By removing unneeded namespaces, not naming all of your controls and getting rid of designer markup you can improve code quality and readability. How do I do it: (This is a 3 in one tip) Remove unused Designer markup: 1) Have you ever wondered what the following code snippet does? xmlns:d="http://schemas.microsoft.com/expression/blend/2008" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" mc:Ignorable="d" d:DesignWidth="640" d:DesignHeight="480" This code is telling the designer to do something special with this page in “Design mode” Specifically the width and the height of the page. When its running in the browser it will not use this information and it is actually ignored by the XAML parser. In other words, if you don’t need it then delete it. 2) If you are not using a namespace then remove it. In the code sample below, I am using Resharper which will tell me the ones that I’m not using by the grayed out line below. If you don’t have resharper you can look in your XAML and manually remove the unneeded namespaces. 3) Don’t name an control unless you actually need to refer to it in procedural code. If you name a control you will take a slight performance hit that is totally unnecessary if its not being called. <TextBlock Height="23" Text="TextBlock" />   That is the end of the series. I hope that you enjoyed it and please check out Part 1 | Part 2 | Part 3 if your hungry for more.  Subscribe to my feed CodeProject

  Read the article

• "Mega Menus" for SEO [duplicate]

  - by Thought Space Designs

  This question already has an answer here: How do I handle having to many links on a webpage because of my menu 4 answers I'm using the term "Mega Menus" loosely here. I'm redesigning my WordPress site (it's going to be responsive), and as part of the redesign, I was debating incorporating some sort of descriptive menu setup. For example, normal navigation drop down menus come in the form of unordered lists of links like so: <nav> <ul> <li> <a href="#">Link1</a> </li> <li> <a href="#">Link2</a> </li> <li> <a href="#">Link3</a> <ul> <li> <a href="#">Sub Link1</a> </li> <li> <a href="#">Sub Link2</a> </li> <li> <a href="#">Sub Link3</a> </li> </ul> </li> <li> <a href="#">Link4</a> </li> </ul> </nav> What I'm looking to do is build my drop down menus with more information than your standard menu. For example, I have a top level link named "Team", and under that link, I want to make a large drop down that contains head shots, headers (in the form of styled p tags) and brief (<100 words) descriptions of each team member (only 2 currently). I want to accompany this with a "Read More" link that takes you to their actual team page. This is just one example, of course, and the other top level links would also have descriptive drop downs in the same fashion. On mobile, I was planning on hiding the "mega menu", and delivering a standard unordered list of links. Here's what I was thinking for overall structure and syntax: <nav> <ul> <li> <a href="#">Home</a> </li> <li> <a href="#">About</a> </li> <li> <a href="#">Team</a> <ul> <!-- DESKTOP --> <li class="mega-menu row"> <a class="col-sm-6" href="#"> <div class="row"> <div class="col-sm-4"> <img src="#" alt="Team Member 1" /> </div> <div class="col-sm-8"> <p class="header">Team Member 1</p> <p>Short description goes here.</p> </div> </div> </a> <a class="col-sm-6" href="#"> <!-- OTHER TEAM MEMBER INFO --> </a> </li> <!-- END DESKTOP --> <!-- MOBILE --> <li> <a href="#">Team Member 1</a> </li> <li> <a href="#">Team Member 2</a> </li> <!-- END MOBILE --> </ul> </li> <li> <a href="#">Contact</a> </li> </ul> </nav> Can anybody think of any potential SEO ramifications of doing this? I'm not going to be loading these menus full of links, so it shouldn't hurt page rank, but what are the effects of having a good bit of text and maybe even forms within nav elements? Is there such a thing as overloading nav with HTML? EDIT: Here's an example of what the menu would look like rendered on desktop. I'm currently hovering the "Team" menu, but you can't see because my mouse went away when I took the screenshot. EDIT 2: This question is not a duplicate. I'm not going to have "too many" links in my menus. I'm wondering how having images and text inside of header navigation will affect my menus. Also, I don't just want "yes, this is bad" answers. Please cite your sources and be specific with reasoning.

  Read the article

• Linux fsck.ext3 says "Device or resource busy" although I did not mount the disk.

  - by matnagel

  I am running an ubuntu 8.04 server instance with a 8GB virtual disk on vmware 1.0.9. For disk maintenance I made a copy of the virtual disk (by making a copy of the 2 vmdk files of sda on the stopped vm on the host) and added it to the original vm. Now this vm has it's original virtual disk sda plus a 1:1 copy (sdd). There are 2 additional disk sdb and sdc which I ignore.) I would expect sdb not to be mounted when I start the vm. So I try tp do a ext2 fsck on sdd from the running vm, but it reports fsck reported that sdb was mounted. $ sudo fsck.ext3 -b 8193 /dev/sdd e2fsck 1.40.8 (13-Mar-2008) fsck.ext3: Device or resource busy while trying to open /dev/sdd Filesystem mounted or opened exclusively by another program? The "mount" command does not tell me sdd is mounted: $ sudo mount /dev/sda1 on / type ext3 (rw,relatime,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) /sys on /sys type sysfs (rw,noexec,nosuid,nodev) varrun on /var/run type tmpfs (rw,noexec,nosuid,nodev,mode=0755) varlock on /var/lock type tmpfs (rw,noexec,nosuid,nodev,mode=1777) udev on /dev type tmpfs (rw,mode=0755) devshm on /dev/shm type tmpfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) /dev/sdc1 on /mnt/r1 type ext3 (rw,relatime,errors=remount-ro) /dev/sdb1 on /mnt/k1 type ext3 (rw,relatime,errors=remount-ro) securityfs on /sys/kernel/security type securityfs (rw) When I ignore the warning and continue the fsck, it reported many errors. How do I get this under control? Is there a better way to figure out if sdd is mounted? Or how is it "busy? How to unmount it then? How to prevent ubuntu from automatically mounting. Or is there something else I am missing? Also from /var/log/syslog I cannot see it is mounted, this is the last part of the startup sequence: kernel: [ 14.229494] ACPI: Power Button (FF) [PWRF] kernel: [ 14.230326] ACPI: AC Adapter [ACAD] (on-line) kernel: [ 14.460136] input: PC Speaker as /devices/platform/pcspkr/input/input3 kernel: [ 14.639366] udev: renamed network interface eth0 to eth1 kernel: [ 14.670187] eth1: link up kernel: [ 16.329607] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/ kernel: [ 16.367540] parport_pc 00:08: reported by Plug and Play ACPI kernel: [ 16.367670] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] kernel: [ 19.425637] NET: Registered protocol family 10 kernel: [ 19.437550] lo: Disabled Privacy Extensions kernel: [ 24.328857] loop: module loaded kernel: [ 24.449293] lp0: using parport0 (interrupt-driven). kernel: [ 26.075499] EXT3 FS on sda1, internal journal kernel: [ 28.380299] kjournald starting. Commit interval 5 seconds kernel: [ 28.381706] EXT3 FS on sdc1, internal journal kernel: [ 28.381747] EXT3-fs: mounted filesystem with ordered data mode. kernel: [ 28.444867] kjournald starting. Commit interval 5 seconds kernel: [ 28.445436] EXT3 FS on sdb1, internal journal kernel: [ 28.445444] EXT3-fs: mounted filesystem with ordered data mode. kernel: [ 31.309766] eth1: no IPv6 routers present kernel: [ 35.054268] ip_tables: (C) 2000-2006 Netfilter Core Team mysqld_safe[4367]: started mysqld[4370]: 100124 14:40:21 InnoDB: Started; log sequence number 0 10130914 mysqld[4370]: 100124 14:40:21 [Note] /usr/sbin/mysqld: ready for connections. mysqld[4370]: Version: '5.0.51a-3ubuntu5.4' socket: '/var/run/mysqld/mysqld.sock' port: 3 /etc/mysql/debian-start[4417]: Upgrading MySQL tables if necessary. /etc/mysql/debian-start[4422]: Looking for 'mysql' in: /usr/bin/mysql /etc/mysql/debian-start[4422]: Looking for 'mysqlcheck' in: /usr/bin/mysqlcheck /etc/mysql/debian-start[4422]: This installation of MySQL is already upgraded to 5.0.51a, u /etc/mysql/debian-start[4436]: Checking for insecure root accounts. /etc/mysql/debian-start[4444]: Checking for crashed MySQL tables.

  Read the article

• Useful software for netbook?

  - by Moayad Mardini

  I'm looking for recommendations of good software that are particularly useful for netbooks. Software that run great on small screens and low CPU/RAM requirments. I'll start off with the following : Operating Systems: Ubuntu Netbook Remix. Easy Peasy: A fork of Ubuntu Netbook Remix that was once called UBuntu EEE. It isn't just for eeePCs though. Definitely worth a look if vanilla Netbook Remix isn't cutting it. (MarkM) Damn Small Linux (Source) Windows 7: With trimming the installation or compressing the Windows directory to fit on an 8GB SSD. (Will Eddins) nLite: A utility to install a lightweight version of Windows XP without the unnecessary components (like Media Player, Internet Explorer, Outlook Express, MSN Explorer, Messenger...). Utilites: TouchFreeze: To disable the touch pad while typing (Source) InSSIDer: Not only does it make it easier to find and keep a wireless connection, but it turns a netbook into the perfect mobile tool for troubleshooting wireless networks. (phenry) AltMove: Adds more functionality to your mouse for interacting with windows. (Rob) ASUS Font Resizer Utility and other tools by ASUS, specific to ASUS Eee PC series. Internet: Run FileZilla FTP client for a small screen : You can hide a lot of FileZilla's interface parts in the View menu, even the directory trees. Go into Settings = Interface and move the message log next to the transfer queue, if you haven't hidden them both or you want to see them. Select a theme with 16x16 icons. (Source) IDEs and Text Editors: Best lightweight IDE/Text Editor: A question on Stack Overflow that has many good suggestions of IDEs and general text editors for programmers. What’s a good linux C/C++ IDE for a low-res screen?: IDEs for Linux-powered netbooks. Online tools: Dropbox: Since the Netbook has limited disk space, you would like to use Cloud Apps like Dropbox and Ubuntu One so that you don't run out of space especially if you are on a holiday. Later when you go back to your desktop with big hard disk,you can take out the files from your dropbox repo. (Manish Sinha) Google products: like Docs, Calendar and Reader (aviraldg) Web sites and software lists: Netbookfiles.com: Netbook specific software downloads. Software Apps to Maximise your Netbook Battery Power: Netbooks are known for their portability. Not only are they small and lightweight but with their increased power efficiency, batteries can last much longer than conventional laptops. This also means you no longer have to carry a power adapter with you! Several brands emphasis the longevity of the battery as a strong selling point, and for those people who travel a lot, it sure is. Free Must-Have Netbook Apps: Finding software for netbooks can present challenges due to limited hard drive space, processor power, RAM, and screen real-estate. That doesn't mean you have to do without essential programs. The apps below cover all the bases -- entertainment, productivity, security, and communication -- without compromising on performance or usability. Best of all, they're free! Useful Netbook Software: With short battery lives and small resolution screens Netbooks, unlike many other computers on the market, could so with some specific software for their use. Now, not all of those I’ve found are specifically designed for Netbooks, but all are relevant. And they’re designed for Windows XP. The question is community wiki, so feel free to edit it. Updated, thank you all for suggestions.

  Read the article

• iproute2 not functioning ("RTNETLINK answers: Operation not supported")

  - by James Watt

  The command and error message: gtwy ~ # ip rule add from 64.251.23.186 table t1 RTNETLINK answers: Operation not supported Older article of the same problem, but it did not help me: http://forums.gentoo.org/viewtopic-t-696982-start-0-postdays-0-postorder-asc-highlight-.html I have looked on google at great lengths to try to find a solution. It seems that my kernel configuration is missing something? Any help or ideas would be appreciated. My system/kernel is: 2.6.36-gentoo-r5 #3 SMP Thu Jan 13 10:49:06 EST 2011 x86_64 Intel(R) Xeon(R) CPU X3220 @ 2.40GHz GenuineIntel GNU/Linux. I am posting this on SuperUser since this system is used as a workstation and this problem is unrelated to specific tasks that are handled exclusively by servers. iproute2 is installed: gtwy etc # emerge --search iproute2 Searching... [ Results for search key : iproute2 ] [ Applications found : 1 ] * sys-apps/iproute2 Latest version available: 2.6.35-r2 Latest version installed: 2.6.35-r2 Size of files: 378 kB Homepage: http://www.linuxfoundation.org/collaborate/workgroups/networking/iproute2 Description: kernel routing and traffic control utilities License: GPL-2 A small snippet of my kernel .config (view entire .config): gtwy linux # cat .config | grep NETLINK CONFIG_NETFILTER_NETLINK=y CONFIG_NETFILTER_NETLINK_QUEUE=y CONFIG_NETFILTER_NETLINK_LOG=y CONFIG_NF_CT_NETLINK=y CONFIG_SCSI_NETLINK=y gtwy linux # cat .config | grep IP_ADVANCED_ROUTER CONFIG_IP_ADVANCED_ROUTER=y gtwy linux # cat .config | grep INGRESS CONFIG_NET_SCH_INGRESS=y gtwy linux # cat .config | grep NET_SCHED CONFIG_NET_SCHED=y emerge --info Portage 2.1.9.25 (default/linux/amd64/10.0, gcc-4.1.2, glibc-2.10.1-r1, 2.6.36-gentoo-r5 x86_64) ================================================================= System uname: Linux-2.6.36-gentoo-r5-x86_64-Intel-R-_Xeon-R-_CPU_X3220_@_2.40GHz-with-gentoo-1.12.13 Timestamp of tree: Thu, 13 Jan 2011 01:15:01 +0000 app-shells/bash: 4.0_p37 dev-java/java-config: 1.3.7-r1, 2.1.10 dev-lang/python: 2.4.6, 2.5.4-r4, 2.6.5-r2, 3.1.2-r3 sys-apps/baselayout: 1.12.13 sys-apps/sandbox: 1.6-r2 sys-devel/autoconf: 2.13, 2.65 sys-devel/automake: 1.9.6-r2::<unknown repository>, 1.10.2, 1.11.1 sys-devel/binutils: 2.20.1-r1 sys-devel/gcc: 4.1.2, 4.3.4, 4.4.3-r2 sys-devel/gcc-config: 1.4.1 sys-devel/libtool: 2.2.6b sys-devel/make: 3.81 virtual/os-headers: 2.6.30-r1 (sys-kernel/linux-headers) ACCEPT_KEYWORDS="amd64" ACCEPT_LICENSE="*" CBUILD="x86_64-pc-linux-gnu" CFLAGS="-march=nocona -O2 -pipe" CHOST="x86_64-pc-linux-gnu" CONFIG_PROTECT="/etc /var/bind" CONFIG_PROTECT_MASK="/etc/ca-certificates.conf /etc/env.d /etc/env.d/java/ /etc/fonts/fonts.conf /etc/gconf /etc/php/apache2-php5/ext-active/ /etc/php/cgi-php5/ext-active/ /etc/php/cli-php5/ext-active/ /etc/revdep-rebuild /etc/sandbox.d /etc/terminfo" CXXFLAGS="-march=nocona -O2 -pipe" DISTDIR="/usr/portage/distfiles" FEATURES="assume-digests binpkg-logs distlocks fixlafiles fixpackages news parallel-fetch protect-owned sandbox sfperms strict unknown-features-warn unmerge-logs unmerge-orphans userfetch" GENTOO_MIRRORS="http://gentoo.chem.wisc.edu/gentoo" LC_ALL="en_US.UTF-8" LDFLAGS="-Wl,-O1 -Wl,--as-needed" LINGUAS="en" MAKEOPTS="-j5" PKGDIR="/usr/portage/packages" PORTAGE_CONFIGROOT="/" PORTAGE_RSYNC_OPTS="--recursive --links --safe-links --perms --times --compress --force --whole-file --delete --stats --timeout=180 --exclude=/distfiles --exclude=/local --exclude=/packages" PORTAGE_TMPDIR="/var/tmp" PORTDIR="/usr/portage" PORTDIR_OVERLAY="/usr/local/portage" SYNC="rsync://rsync.namerica.gentoo.org/gentoo-portage" USE="acl amd64 apache2 berkdb bzip2 cli cracklib crypt ctype cups curl cxx dri fortran gdbm gpm iconv jpeg jpeg2k libwww mmx modules mudflap multilib mysql ncurses nls nptl nptlonly openmp pam pcre perl php png pppd python readline session sockets sse sse2 ssl symlink sysfs tcpd threads unicode vhosts xml xorg xsl zlib" ALSA_CARDS="ali5451 als4000 atiixp atiixp-modem bt87x ca0106 cmipci emu10k1x ens1370 ens1371 es1938 es1968 fm801 hda-intel intel8x0 intel8x0m maestro3 trident usb-audio via82xx via82xx-modem ymfpci" ALSA_PCM_PLUGINS="adpcm alaw asym copy dmix dshare dsnoop empty extplug file hooks iec958 ioplug ladspa lfloat linear meter mmap_emul mulaw multi null plug rate route share shm softvol" APACHE2_MODULES="actions alias auth_basic authn_alias authn_anon authn_dbm authn_default authn_file authz_dbm authz_default authz_groupfile authz_host authz_owner authz_user autoindex cache cgi cgid dav dav_fs dav_lock deflate dir disk_cache env expires ext_filter file_cache filter headers include info log_config logio mem_cache mime mime_magic negotiation rewrite setenvif speling status unique_id userdir usertrack vhost_alias" COLLECTD_PLUGINS="df interface irq load memory rrdtool swap syslog" ELIBC="glibc" GPSD_PROTOCOLS="ashtech aivdm earthmate evermore fv18 garmin garmintxt gpsclock itrax mtk3301 nmea ntrip navcom oceanserver oldstyle oncore rtcm104v2 rtcm104v3 sirf superstar2 timing tsip tripmate tnt ubx" INPUT_DEVICES="keyboard mouse evdev" KERNEL="linux" LCD_DEVICES="bayrad cfontz cfontz633 glk hd44780 lb216 lcdm001 mtxorb ncurses text" LINGUAS="en" PHP_TARGETS="php5-3" RUBY_TARGETS="ruby18" USERLAND="GNU" VIDEO_CARDS="fbdev glint intel mach64 mga neomagic nouveau nv r128 radeon savage sis tdfx trident vesa via vmware dummy v4l" XTABLES_ADDONS="quota2 psd pknock lscan length2 ipv4options ipset ipp2p iface geoip fuzzy condition tee tarpit sysrq steal rawnat logmark ipmark dhcpmac delude chaos account" Unset: CPPFLAGS, CTARGET, EMERGE_DEFAULT_OPTS, FFLAGS, INSTALL_MASK, LANG, PORTAGE_BUNZIP2_COMMAND, PORTAGE_COMPRESS, PORTAGE_COMPRESS_FLAGS, PORTAGE_RSYNC_EXTRA_OPTS

  Read the article

• Ubuntu: Failure to login with multiple video adapters

  - by tsilb

  Forgive my ignorance, for I am a complete linux noob. I have a computer with three video cards and six monitors. Works great on Windows. Trying to get it to run Ubuntu as well. It loads fine when I have it configured to run on one adapter; detects both screens, runs ok. But I want to turn the other 4 monitors on and run the whole thing as one extended desktop (one session, etc). So I downloaded and installed the newest ATI driver for Linux, which seems to work, kinda. I ran this to set up the screens: aticonfig --adapter=all --initial -f Now when I boot, Ubuntu seems to turn on all the screens (3 viewports, each with two cloned displays from what I can tell). When I enter my login info OR move the mouse off the main screen, the screens freeze and the kbd/ms become unresponsive. aticonfig generated xorg.conf included below. Have tried the following: aticonfig -initial -f - works, but only detects the primary adapter and 2 screens aticccle - Tells me I have to reboot after enabling the other cards. Then goes into above described freezing state. aticonfig --adapter=all --initial -f - see above Manually editing xorg.conf file with my limited knowledge - Was able to get two adapters running, but only the second adapter initialized while the primary stopped at the Ubuntu boot screen. Was unable to see the login prompt. Froze after I logged in blindly (was able to hear the login sound). Using generic "radeon" driver instead of ATI Proprietary driver with the above init attempts Toggling xinerama Various combinations of the above Hardware: Intel Core 2 Quad q6600 8GB DDR2 (3x) ATI Radeon HD 4680 5 monitors (21W, 21W, 22W Portrait, 22W Portrait, 19")and an HDTV (26"W, HDMI) in a horizontal arrangement I know next to nothing about Linux/Ubuntu aside from basic filesystem navigation, editing text files, and accessing my local and networked Windows stores and shares. Basically this is the most advanced thing I've had to do. I installed today. Please advise how to make this configuration work. my xorg.conf: Section "ServerLayout" Identifier "Layout0" Screen 0 "aticonfig-Screen[0]-0" 0 0 Screen "aticonfig-Screen[1]-0" RightOf "aticonfig-Screen[0]-0" Screen "aticonfig-Screen[2]-0" RightOf "aticonfig-Screen[1]-0" Option "RenderAccel" "true" Option "AllowGLXWithComposite" "true" EndSection Section "Files" EndSection Section "Module" EndSection Section "ServerFlags" Option "Xinerama" "0" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[1]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[2]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "aticonfig-Device[1]-0" Driver "fglrx" BusID "PCI:3:0:0" EndSection Section "Device" Identifier "aticonfig-Device[2]-0" Driver "fglrx" BusID "PCI:4:0:0" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[1]-0" Device "aticonfig-Device[1]-0" Monitor "aticonfig-Monitor[1]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[2]-0" Device "aticonfig-Device[2]-0" Monitor "aticonfig-Monitor[2]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

  Read the article

• Server 2003 R2 doesn't allow logon after a few days of uptime

  - by Bryan

  We have a server 2003 R2 standard (which I'll refer to as SRV01) that's knocking on a bit now, but it still acts as a file, print and SQL server on our company's network. SRV01 hosts user profiles, home directories and pretty much all our business data. Note our AD is currently at 2008 R2 level. This server is due to be upgraded in the next 12 months, but I've no budget to spend on it just yet. A bit of history of this server follows: When SRV01 was first commissioned, it acted as a domain controller (with the same 2003 R2 install it has today), paired with another server that ran Server 2003 R2 SBS. A few years ago, we purchased a pair of dedicated DCs (2008 R2) and at this point we decommissioned the 2003 SBS server, and SRV01 was DCPROMOed out of the AD. Up until very recently, SRV01 used to run Exchange 2003, however we've recently purchased a dedicated server for Exchange 2010 and upgraded (following Microsoft recommended upgrade path). Exchange 2003 was recently uninstalled. - Cleanly to the best of my knowledge. Ever since Exchange was removed from SRV01, I'm finding that after a few days of uptime, when I attempt to logon, pressing CTRL-ALT-DEL just hides the Welcome to Windows Server 2003 banner, and never presents the logon dialog. All I see is a moveable mouse pointer and a blank background. It's a similar story with an admin TS session, the RDP client connects and gives me a blank background, but no logon dialog is presented. The RDP session indefinitely hangs until I give up and close it. The only way I've been able to gain access to the server is to pull the plug on it. Whilst the server does have a battery backed up RAID 5 controller, I'm unhappy about having to do this, so as a temporary measure, I've created a scheduled job to reboot SRV01 each night. Not only do I not like the idea of scheduling a reboot of a server like this, but it is also causing problems for users that leave desktop PCs left logged on overnight. Users complain of 'Delayed Write Failures', and there has also been a number of users that have started to complain about account lockout problems, as well as users not able to connect to shares on SRV01 until they reboot their desktop PCs. I've examined event logs on SRV01 and on the DCs looking for clues as to what the problem is, but there really is nothing untoward being logged. How could I being to investigate this problem when nothing of any relevance is being logged? Is there some additional logging that can be enabled that might give some clues as to what could be causing this problem? Could performance monitor help me out here, and if so, what counters would you consider monitoring? It's worth mentioning that whilst the server is unresponsive via the console and TS, it does still respond to clients connecting to shares without problems for several days, but after about a week I then start to hear users reporting problems accessing shares, but this seems quite sporadic. I've also tried leaving the console logged on (and locked), when I notice I can no longer logon via TS, I can unlock the server console without problem, but it refuses to reboot/shutdown, and subsequent attempts to reboot report that a system shutdown is already in progress and the system then completely hangs. I've tried playing the waiting game for several hours thinking that a timeout might allow the shutdown to continue, but to no avail.

  Read the article

• Blank black screen with cursor after login -- RHEL5

  - by Sean O.

  I have a RHEL 5 machine here which is a Dell Precision T3500. I'm an Ubuntu guy, but I'm having a heck of a time with this machine. After processing its first security update, we cannot log in via the gdm greeter. A new kernel was installed; then I installed the nVidia drivers for our Quadro NVS 295. I know the X configuration is valid because the gdm greeter does display; however, upon login all we can get is a blank, black screen with a cursor. I thought perhaps our python installation was corrupted but a reinstall via yum has not helped. I have searched & googled extensively for a potential fix for this and can find nothing. Below are outputs from uname, a tail of an error in /var/log/messages, and the Xorg.conf. Can anyone suggest a course of action? [sean@cheetah ~]$ uname -a Linux cheetah.*.* 2.6.18-308.8.1.el5 #1 SMP Fri May 4 16:43:02 EDT 2012 x86_64 x86_64 x86_64 GNU/Linux [sean@cheetah ~]$ sudo tail /var/log/messages Jun 5 15:03:04 cheetah gconfd (sean-4592): Resolved address "xml:readonly:/etc/gconf/gconf.xml.defaults" to a read-only configuration source at position 2 Jun 5 15:03:05 cheetah hcid[3855]: Default passkey agent (:1.8, /org/bluez/applet) registered Jun 5 15:03:05 cheetah pcscd: winscard.c:304:SCardConnect() Reader E-Gate 0 0 Not Found Jun 5 15:03:05 cheetah last message repeated 2 times Jun 5 15:03:06 cheetah gconfd (sean-4592): Resolved address "xml:readwrite:/home/sean/.gconf" to a writable configuration source at position 0 Jun 5 15:03:06 cheetah setroubleshoot: [program.ERROR] exception ImportError: /usr/lib/libatk-1.0.so.0: undefined symbol: g_assertion_message_expr Traceback (most recent call last): File "/usr/bin/sealert", line 952, in ? from setroubleshoot.gui_utils import * File "/usr/lib/python2.4/site-packages/setroubleshoot/gui_utils.py", line 26, in ? import gtk File "/usr/lib64/python2.4/site-packages/gtk-2.0/gtk/__init__.py", line 48, in ? from gtk import _gtk ImportError: /usr/lib/libatk-1.0.so.0: undefined symbol: g_assertion_message_expr Jun 5 15:03:07 cheetah setroubleshoot: [program.ERROR] exception ImportError: /usr/lib/libatk-1.0.so.0: undefined symbol: g_assertion_message_expr Traceback (most recent call last): File "/usr/bin/sealert", line 952, in ? from setroubleshoot.gui_utils import * File "/usr/lib/python2.4/site-packages/setroubleshoot/gui_utils.py", line 26, in ? import gtk File "/usr/lib64/python2.4/site-packages/gtk-2.0/gtk/__init__.py", line 48, in ? from gtk import _gtk ImportError: /usr/lib/libatk-1.0.so.0: undefined symbol: g_assertion_message_expr Jun 5 15:03:08 cheetah pcscd: winscard.c:304:SCardConnect() Reader E-Gate 0 0 Not Found Jun 5 15:07:01 cheetah ntpd[4114]: synchronized to 64.16.211.38, stratum 3 Jun 5 15:07:01 cheetah ntpd[4114]: kernel time sync enabled 0001 [sean@cheetah ~]$ cat /etc/X11/xorg.conf # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 295.53 ([email protected]) Sat May 12 00:34:20 PDT 2012 # Xorg configuration created by system-config-display Section "ServerLayout" Identifier "single head configuration" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" Option "XkbModel" "pc105" Option "XkbLayout" "us" EndSection Section "Monitor" ### Comment all HorizSync and VertSync values to use DDC: ### Comment all HorizSync and VertSync values to use DDC: Identifier "Monitor0" ModelName "LCD Panel 1600x1200" HorizSync 31.5 - 74.7 VertRefresh 56.0 - 65.0 Option "dpms" EndSection Section "Device" Identifier "Videocard0" Driver "nvidia" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

  Read the article

• Chrome does not re-draw properly on Windows 8

  - by Akshat Mittal

  There are a lot of problems with Chrome (24.0.1312.14 beta || But all this happened before update also) on Windows 8. Problems and explanations are listed below: Google Chrome re-draw time: When I switch tabs, the window retains the content of the previous tab and displays that even if I move my mouse, if only refreshes (re-draws) when there is a change on the webpage (like on hover) or I do a select all (or scroll). One thing to note is that the hover and select happens on the real page and not the retained image-like thing of the older webpage. Chrome is slow and laggy: Websites such as Facebook and Twitter (and more) have gone extremely laggy on Chrome (Win 8). When I was using Windows 7, I never experienced a lag or something. Also when using HTML-5 Websites, the transition (the -webkit-transition in CSS) goes extremely slow at times. Plugins Crash: Plugins like Flash Player, Shockwave Player, and more that are in-built into Chrome Crashes a lot, even when doing simple tasks like playing YouTube Videos, displaying ads or something. Chrome Crashes: Chrome has crashed over 100 times in the past month. Google Chrome just crashes randomly or I don't know the reason. Random Page crashes: Chrome results chrome://crash/(Copy-Paste this in address bar) on random pages even when the page is just loaded, I understand that this can happen on heavy HTML5 or JS websites but what about HTML only websites? Computer Freeze: Chrome sometimes, randomly, freezes my computer. Freeze in the sense, none of the other apps are also working. It's like the whole system freezes, I can not even switch to other apps. I am sure that this is because of Chrome since this happens only when Chrome is active. Most of the things above happens on Super User also, Super User never had any problem when using Chrome on Windows 7. UPDATE 1: @magicandre1981 Commented for trying to disable Hardware Acceleration. I tried it, it somewhat solved the problem but din't fix it. I am still experiencing all the above issues but less frequently (maybe because Chrome Restarted Completely) UPDATE 2: @avirk asked me to try a Stable Version of Chrome and Firefox, I din't experience any lag in Firefox, a little (negligible) lag in Chrome 22 (Maybe because its a new copy of Chrome, I haven't used it much). UPDATE 3: @NothingsImpossible said that He is also experiencing the same problem on Windows Server 2008! This seams to be a major issue now. He also said that GPU load is also high at the same time! Even I saw the same thing. UPDATE 4: Recently, Chrome updated to v24 Stable (I am using stable from a long time now). I was experiencing this problem a lot less in Chrome 23, but this is back in Chrome 24. Seams like Chrome 24 is the most affected from this bug, as this same problem was high in Chrome 24 beta also. UPDATE 5: Chrome was updated to v25 Stable. This problem is 99% Gone, it is still there in 1% of the cases. One such example is when I leave chrome inactive for a while with a few tabs open, the tabs go black and no activity can get them back to active state. If I open a new tab, the new tab is OK but the others are still black, I need to close all those tabs. UPDATE 6: Chrome updated to v27 Stable channel, this problem is nearly gone. This does happen occasionally, but not as frequent as in earlier versions of Chrome. UPDATE 7: I am on Chrome v35.0.1916.114 Stable, Windows 8.1 Pro Update 1. Some of the other problems appears to be back. Chrome is slow and laggy again. Re-draw time is getting worse. Is anybody else experiencing such issues? Does anybody have a solution to any of these?

  Read the article

• Excel: conditionally format a cell using the format of another, content-matching cell

  - by Eric A. Meyer

  I have an Excel spreadsheet where I’d like to be able to create a “key” of formatted cells with unique values, and then in another sheet format cells using the key formatting. So for example, my key is as follows, with one value per cell and the visual formatting indicated in parentheses: A (red background) B (green background) C (blue background) So that’s on one sheet (or in a remote corner of the current sheet—whichever is better). Then, in an area that I mark for conditional formatting, I can type one of those three letters and have the cell where I typed it visually formatted according to the key. So if I type a “B” into one of the conditionally formatted cells, it gets a green background. (Note that I’m using backgrounds here solely for ease of explanation: ideally I want to have all visual formatting copied over, whether it’s foreground color, background color, font weight, borders, or whatever. But I’ll take what I can get, obviously.) And—just to make it extra-tricky—if I change the formatting in the key, that change should be reflected in cells that reference the key. Thus, if I change the “B” formatting in the key from a green background to a purple background, any “B” in the main sheet should switch to the new color. Similarly, it should be possible to add or remove values from the key and have those changes applied to the main data set. I’m okay with the formatting-update-on-key-change being triggered by clicking a button or something. I suspect that if any of this is possible it will require VBA, but I’ve never used it so I’ve no idea where to start if that’s the case. I’m hoping it’s possible without VBA. I know it’s possible to just use multiple conditional formats, but my use case here is that I’m trying to create the above-described capability for someone who isn’t conversant with conditional formatting. I’d like to let them be able to define a key, update it if necessary, and keep on truckin’ without me having to rewrite the spreadsheet’s formatting rules for them. --- UPDATE --- So I think I was a bit unclear about my original request. Let me try again with an image. The image shows the “key” on the left, where values and styles are defined using keyboard and mouse input. On the right, you see the data that should be formatted to match the key. Thus if I type a “C” into a cell in the Data area, it should be blue-backed. Furthermore, if I change the formatting of “C” in the Key to have a purple background, all the “C” cells should switch from blue to purple. For further craziness, if I add more to the Key (say, “D” with a yellow background) then any “D” cells will be styled to match; if I remove a Key entry, then matching values in the Data area should revert to default styling. So. Is that more clear? Is it possible, in whole or in part? I don’t have to use conditional formatting for this; in fact, at this point I suspect I probably shouldn’t. But I’m open to any approach!

  Read the article

• Synergy 1.4.2 Linux server, OSX client, Media/Function key mapping issues

  - by at165dB

  I'm using an Apple bluetooth keybord to control my Linux synergy server. SSH tunneling, Mouse, Keyboard, and Copy&Paste all work. Linux sees all the media/app keys that are on top of the F# keys correctly. However if I press any of those keys while controlling my OSX client, nothing happens on the client. Running synergys with -d DEBUG1 I can see the following keycode info: Pressing the "dim monitor" key that also serves as F1 generates: new mask: 0x2000 event: KeyPress code=232, state=0x0010 new mask: 0x2000 If I press "fn" and the same key, I can see it sending what I'm assuming is an F1: event: KeyPress code=67, state=0x0010 onKeyDown id=61374 mask=0x2000 button=0x0043 send key down to "foo.cisco.com" id=61374, mask=0x2000, button=0x0043 new mask: 0x2000 event: KeyRelease code=67, state=0x0010 onKeyUp id=61374 mask=0x2000 button=0x0043 send key up to "foo.cisco.com" id=61374, mask=0x2000, button=0x0043 I'm guessing I need to tweak my synergy.conf so that the server sends keys that it currently isn't. I'm also not sure what I need to do to tweak the keys that it is sending, but are not working. Below are all the other keys I'm having issues with. Does anyone have any idea how I can enable their functionality? brighten monitor: new mask: 0x2000 event: KeyPress code=233, state=0x0010 new mask: 0x2000 expose: new mask: 0x2000 event: KeyPress code=128, state=0x0010 new mask: 0x2000 dashboard: new mask: 0x2000 event: KeyPress code=212, state=0x0010 new mask: 0x2000 dim keyboard: new mask: 0x2000 event: KeyPress code=237, state=0x0010 new mask: 0x2000 brighten keyboard: new mask: 0x2000 event: KeyPress code=238, state=0x0010 new mask: 0x2000 rewind: event: KeyPress code=173, state=0x0010 onKeyDown id=57521 mask=0x2000 button=0x00ad send key down to "foo.cisco.com" id=57521, mask=0x2000, button=0x00ad new mask: 0x2000 event: KeyRelease code=173, state=0x0010 onKeyUp id=57521 mask=0x2000 button=0x00ad send key up to "foo.cisco.com" id=57521, mask=0x2000, button=0x00ad play/pause: event: KeyPress code=172, state=0x0010 onKeyDown id=57523 mask=0x2000 button=0x00ac send key down to "foo.cisco.com" id=57523, mask=0x2000, button=0x00ac new mask: 0x2000 event: KeyRelease code=172, state=0x0010 onKeyUp id=57523 mask=0x2000 button=0x00ac send key up to "foo.cisco.com" id=57523, mask=0x2000, button=0x00ac fastforward: event: KeyPress code=171, state=0x0010 onKeyDown id=57520 mask=0x2000 button=0x00ab send key down to "foo.cisco.com" id=57520, mask=0x2000, button=0x00ab new mask: 0x2000 event: KeyRelease code=171, state=0x0010 onKeyUp id=57520 mask=0x2000 button=0x00ab send key up to "foo.cisco.com" id=57520, mask=0x2000, button=0x00ab mute: event: KeyPress code=121, state=0x0010 onKeyDown id=57517 mask=0x2000 button=0x0079 send key down to "foo.cisco.com" id=57517, mask=0x2000, button=0x0079 new mask: 0x2000 event: KeyRelease code=121, state=0x0010 onKeyUp id=57517 mask=0x2000 button=0x0079 send key up to "foo.cisco.com" id=57517, mask=0x2000, button=0x0079 volume down: onKeyDown id=57518 mask=0x2000 button=0x007a send key down to "foo.cisco.com" id=57518, mask=0x2000, button=0x007a new mask: 0x2000 event: KeyRelease code=122, state=0x0010 onKeyUp id=57518 mask=0x2000 button=0x007a send key up to "foo.cisco.com" id=57518, mask=0x2000, button=0x007a volume up: event: KeyPress code=123, state=0x0010 onKeyDown id=57519 mask=0x2000 button=0x007b send key down to "foo.cisco.com" id=57519, mask=0x2000, button=0x007b new mask: 0x2000 event: KeyRelease code=123, state=0x0010 onKeyUp id=57519 mask=0x2000 button=0x007b send key up to "foo.cisco.com" id=57519, mask=0x2000, button=0x007b eject: event: KeyPress code=169, state=0x0010 onKeyDown id=57345 mask=0x2000 button=0x00a9 send key down to "foo.cisco.com" id=57345, mask=0x2000, button=0x00a9 new mask: 0x2000 event: KeyRelease code=169, state=0x0010 onKeyUp id=57345 mask=0x2000 button=0x00a9 send key up to "foo.cisco.com" id=57345, mask=0x2000, button=0x00a9

  Read the article

• How to diagnose computer lockup/freezing problem

  - by Scott Mitchell

  I built a desktop computer a couple years back with the following specs: CPU: Intel Core 2 Quad Q9300 Yorkfield 2.5GHz 6MB L2 Cache LGA 775 95W Quad-Core Processor BX80580Q9300 Motherboard: EVGA 122-CK-NF68-T1 LGA 775 NVIDIA nForce 680i SLI ATX Intel Motherboard Video Card: Two EVGA 256-P2-N758-TR GeForce 8600GT SCC 256MB 128-bit GDDR3 PCI Express x16 SLI Supported Video Card PSU: SeaSonic S12 Energy Plus SS-550HT 550W ATX12V V2.3 / EPS12V V2.91 SLI Certified CrossFire Ready 80 PLUS Certified Active PFC Power Supply Memory: Two G.SKILL 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model F2-6400CL5D-4GBPQ Since its inception, the machine has periodically locked up, the regularlity having varied over the years from once a day to once a month. Typically, lockups happen once every few days. By "lockup" I mean my computer just freezes. The screen locks up, I can't move the mouse. Hitting keys on my keyboard that normally turn LEDs on or off on the keyboard (such as Caps Lock) no longer turn the LEDs on or off. If there was music playing at the time of the lockup, noise keeps coming out of the speakers, but it's just the current frequency/note that plays indefinitely. There is no BSOD. When such a lockup occurs I have to do a hard reboot by either turning off the computer or hitting the reset button. I have the most recent version of the NVIDIA hardware drivers, and update them semi-regularly, but that hasn't seemed to help. I am currently using Windows 7 x64, but was previously using Windows Server 2003 x64 and having the same lockup issues. My guess is that it's somehow video driver or motherboard related, but I don't know how to go about diagnosing this problem to narrow down which of the two is the culprit. Additional information re: cooling Regarding cooling... I've not installed any after-market cooling systems aside from two regular fans I scavenged from an older computer. The fan atop the CPU is the one that shipped with it. One of the two scavenged fans I added it located at the bottom tower of the corner, in an attempt to create some airflow from front to back. The second fan is pointed directly at the two video cards. SpeedFan installation and readings Per studiohack's suggestion, I installed SpeedFan, which provided the following temperature readings: GPU: 63C GPU: 65C System: 76C CPU: 64C AUX: 36C Core 0: 78C Core 1: 76C Core 2: 79C Core 3: 79C Update #3: Another Lockup :-( Well, I had another lockup last night. :-( SpeedFan reported the CPU temp at 38 C when it happened, and there was no spike in temperature leading up to the freeze. One thing I notice is that the freeze seems more likely to happen if I am watching a video. In fact, of the last 5 freezes over the past month, 4 of them have been while watching a video on Flickr. Not necessarily the same video, but a video nevertheless. I don't know if this is just coincidence or if it means anything. (As an aside, each night before bedtime my 2 year old daughter sits on my lap and watches some home videos on Flickr and, in the last month, has learned the phrase, "Uh oh, computer broke.") Update #4: MemTest86 and 3DMark06 Test Results: Per suggestions in the comments, I ran the MemTest86 overnight and it cycled through the 8 GB of memory 5 times without error. I also ran the 3DMark06 test without a problem (see my scores at http://3dmark.com/3dm06/15163549). So... what now? :-) Any further suggestions on what to check? Is there some way to get a stack trace or something when the computer locks like that? Thanks

  Read the article

• Yet again: "This device can perform faster" (Samsung Galaxy Tab 2)

  - by Mike C

  I've been doing a lot of research with no reasonable solution. Please excuse the length of my post. When I plug my Galaxy Tab 2 (7" / Wi-Fi only / Android ICS) into my Windows 7 64-bit machine, I (almost always) get this warning popup that "This device can perform faster." And in fact, transfers onto the Tab in this mode are slow. The two times I've been able to get a high-speed connection, the transfer has occurred at the expected speed. I just don't know what to do to get that high-speed transfer. (The first time I did, it was the first time I connected the Tab; the second time I did, I was fiddling around and unplugging/plugging in again.) That popup is telling me that the device is USB2, but that it thinks I've connected to a USB1 port. In fact, every USB port (there are ten) on this system is USB2. It's an ASUS M3A78-EMH mobo from late 2008. I'm not sure what the chipset is; the CPU is an AMD Athlon 4850e, but I've seen this message reported for non-AMD systems. (Every mobo reference I've seen in reports on this has been for Asus, but of course most reporters aren't reporting that info at all.) The Windows 7 installation is just a couple weeks old (I had a disk crash) but I saw the same warning on the WinXP/64 that was installed previously. In Device Manager, there are two "Standard Enhanced PCI to USB Host Controller" nodes which are the actual high-speed controllers. There are also five "Standard OpenHCD USB Host Controller" nodes, which I have determined are virtual USB1 controllers embedded in the "Enhanced" controllers. (In Device Manager, I'm using View|Devices by Connection.) My high-speed thumb drives, external disks, and iPod all show up as subnodes of the "Enhanced" controllers; the keyboard, mouse, and USB speakers under the "OpenHCD" ones -- and this is true no matter which ports these devices are plugged into. The Tab shows up under an OpenHCD node, unsurprisingly. It appears as a threesome: a top-level "Mobile USB Composite device" with two subs: "Galaxy Tab 2" and "Mobile USB Modem." (I have no idea what the modem device implies or how I might use it, but I don't care about it either: I just want the Tab to reliably connect at high speed.) On the Tab, the USB support has a switch between PTP and MTP, the latter being the default, and the preferred mode for me (as I'm usually hooking it up for music synch). I have tried, however, connecting it as PTP, and it still connects as USB 1. (As PTP, only the "Galaxy Tab 2" device appears -- no Composite, no Modem.) If it's plugged in as MTP and I change the setting to PTP, Windows unloads and reloads the device, and voila: The Tab appears under an "Enhanced" node, but eventually re-loads again to show a exclamation icon on the device; Properties then shows "This device cannot start." Same response if I plug it in as PTP and then change to MTP; in this case, only the Tab itself shows the exclamation, not the other two devices. One thing I have not tried, and really would prefer to avoid, is installing the "beta" chipset driver available on the Asus website, which is dated 2009. Windows tells me it has the most up-to-date drivers for the Tab, and for the chipset, and I'm inclined to believe that. I suspect the problem is with the Samsung drivers, or possibly the hardware. One suggestion I saw elsewhere which might, possibly, pertain is to ensure the USB cable is properly shielded; however, the Tab has one of those misbegotten 30-pin, not-quite-an-iPod connectors; I don't know if I could find a 3rd party one. It seems unlikely that this cable is improperly shielded, tho. (Is there a way to test that?) So, my question is: does anyone know how to get this working as one might reasonably expect it to?

  Read the article

• ubuntu 10.04; kvm bridged networking not working with public ip addresses

  - by senorsmile

  I have a dedicated hosted server box with ubuntu 10.04 64 bit installed. I would like to run kvm with ubuntu 8.04 installed for some php 5.2 compatible apps(they don't work right with php 5.3, the default in ubuntu 10.04). I installed KVM as instructed at https://help.ubuntu.com/community/KVM/Installation . I installed the vm using virt-manager. I never could figure out how use virt-install or any of those automated installers. I just installed it using the disc. I set up bridged networking as per https://help.ubuntu.com/community/KVM/Networking . However, the bridged connection doesn't work. Here's my /etc/network/interfaces on the host, running ubuntu 10.04. (with specific public ip blanked) auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address xx.xx.xx.xx netmask 255.255.255.248 gateway xx.xx.xx.xa bridge_ports eth0 bridge_stp on bridge_fd 0 bridge_maxwait 10 ` Here's my /etc/network/interfaces on the guest, running ubuntu 8.04. auto lo iface lo inet loopback auto eth0 iface eth0 inet static address xx.xx.xx.xy netmask 255.255.255.248 gateway xx.xx.xx.xa The two vm's can communicate to each other. But, the guest vm can't access anyone in the real world. Here's my /etc/libvirt/qemu/store_804.xml <domain type='kvm'> <name>store_804</name> <uuid>27acfb75-4f90-a34c-9a0b-70a6927ae84c</uuid> <memory>2097152</memory> <currentMemory>2097152</currentMemory> <vcpu>2</vcpu> <os> <type arch='x86_64' machine='pc-0.12'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/var/lib/libvirt/images/store_804.img'/> <target dev='hda' bus='ide'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> </disk> <interface type='bridge'> <mac address='52:54:00:26:0b:c6'/> <source bridge='br0'/> <model type='virtio'/> </interface> <console type='pty'> <target port='0'/> </console> <console type='pty'> <target port='0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes'/> <sound model='es1370'/> <video> <model type='cirrus' vram='9216' heads='1'/> </video> </devices> </domain> Any idea where I've gone wrong?

  Read the article

• Windows 7 sometimes boots in VGA mode

  - by TuxRug

  I have an Asus G50VT-x5 laptop with nVidia GeForce9800M-GS graphics. Normally, Windows boots normally, but about 20% of the time (rough estimate), it will boot with the fallback VGA driver, maxing out at 800x600 with no Aero. I've checked the system logs and there is nothing indicating an error loading the nVidia driver. It even specifies in the logs that the Nvidia Display Driver service started successfully, even though it has booted in safe graphics mode. This has been happening for a while, but it's happening a little more often now than it was before. Since the first time my system exhibited this behavior, I have updated my graphics driver a handful of times. I used System Information for Windows to check for problems there, but the only thing that stood out was the following: Core Temperature 4486449 °C (8075639 °F) Shaders Temperature 1171513530 °C (2108724330 °F) I know this reading is incorrect, because my laptop is nowhere near the surface of the sun and my desk has not burst into flames. When it's opererating normally, I get a sane reading like [Core Temperature 58 °C (136 °F)] with no Shaders Temperature listed. All I have to do to resolve the issue is reboot. I have seen no stability issues with the graphics or anything else. A long time ago, I had an issue with this computer where my framerate would suddenly drop during a 3D game from 40fps to <1fps, but after looking at the temperature readout immediately after quitting a game, I removed the bottom panel and blew the dust out of the vent and heatsink. Since then I have no drops in framerate under any situation. I have uploaded a zip containing the SIW reports for when the problem is occurring and when the computer is operating normally. I don't have a paid account so it can only be downloaded 10 times, so please only download the reports if you think you can use them. If you try to download the reports and they are no longer available, please comment and I will re-upload them. If you want to look at the files, they are on Rapidshare. EDIT It happened again, and I looked a little deeper into the System logs. When this happens, there are a lot of errors about other device drivers unable to start. All of these errors are for PnP drivers. Also, my USB keyboard and mouse take a few moments before they actually start working, although this happens sometimes the first normal boot as well. I am quite sure this is related, so I am adding the pnp tag. Also, CHKDSK will not run on boot. Even if a check is scheduled or a volume is manually set as dirty, CHKDSK will be skipped entirely, not even leaving an entry in the System logs. I tried running CHKNTFS /D, which did not work. I then manually changed my HKLM\System\CurrentControlSet\Control\Session Manager BootExecute value to the default listed on Microsoft's website. That did not work either. I ended up booting to repair mode and running CHKDSK there, which found a number of minor inconsistencies on my system drive, but none on my data drive. I have no idea if this is related. Some more information for those who don't download my SIW report file: Antivirus and Firewall are ESET Smart Security I have three different virutalization programs installed: VMware Player, Windows Virtual PC, and VirtualBox. The network adapters for these show up in the log of failed device starts. EDIT 2 I tried running sfc /scannow, which reported that it found corrupted files that could not be fixed. The CBS log is extremely cryptic. I tried booting to my install disk, launching repair mode, and doing an offline sfc from there, which produced the same result.

  Read the article

• Logitech USB headphones detected and selected in Debian Squeeze but sound still coming from speakers

  - by mattalexx

  I have a pair of Logitech wireless USB headphones that work with Ubuntu Natty but aren't working in Debian Squeeze. When they are selected as the default audio output, the sound comes out of the speakers instead of the headphones. I have rebooted and tried using a different USB port. My computer is a Thinkpad T510. How can I fix this problem? Here is lsusb: Bus 002 Device 005: ID 046d:0a29 Logitech, Inc. Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 005: ID 046d:c52f Logitech, Inc. Wireless Mouse M305 Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Here is cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xf2420000 irq 17 1 [Headset ]: USB-Audio - Logitech Wireless Headset Logitech Logitech Wireless Headset at usb-0000:00:1d.0-1.1, full speed 2 [NVidia ]: HDA-Intel - HDA NVidia HDA NVidia at 0xcdefc000 irq 17 Here is the gnome-volume-control GUI: Here's lsmod | grep usb: snd_usb_audio 50670 0 snd_usb_lib 11192 1 snd_usb_audio usbhid 28008 0 hid 50909 1 usbhid snd_rawmidi 12513 2 snd_usb_lib,snd_seq_midi snd_hwdep 4054 2 snd_usb_audio,snd_hda_codec snd_pcm 47226 3 snd_usb_audio,snd_hda_intel,snd_hda_codec usbcore 98969 5 snd_usb_audio,snd_usb_lib,usbhid,ehci_hcd snd 34423 11 snd_usb_audio,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device nls_base 4541 1 usbcore Here's cat /etc/modprobe.d/alsa-base.conf: # autoloader aliases install sound-slot-0 /sbin/modprobe snd-card-0 install sound-slot-1 /sbin/modprobe snd-card-1 install sound-slot-2 /sbin/modprobe snd-card-2 install sound-slot-3 /sbin/modprobe snd-card-3 install sound-slot-4 /sbin/modprobe snd-card-4 install sound-slot-5 /sbin/modprobe snd-card-5 install sound-slot-6 /sbin/modprobe snd-card-6 install sound-slot-7 /sbin/modprobe snd-card-7 # Cause optional modules to be loaded above generic modules install snd /sbin/modprobe --ignore-install snd && { /sbin/modprobe --quiet snd-ioctl32 ; /sbin/modprobe --quiet snd-seq ; } install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi && { /sbin/modprobe --quiet snd-seq-midi ; : ; } install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 && { /sbin/modprobe --quiet snd-emu10k1-synth ; : ; } # Prevent abnormal drivers from grabbing index 0 options bt87x index=-2 options cx88_alsa index=-2 options snd-atiixp-modem index=-2 options snd-intel8x0m index=-2 options snd-via82xx-modem index=-2 # Keep snd-pcsp from beeing loaded as first soundcard options snd-pcsp index=-2 # Keep snd-usb-audio from beeing loaded as first soundcard options snd-usb-audio index=-2 EDIT In VLC, I reset VLC prefs (Output: Default) and sound still comes out of speakers as expected. Then I change it to "Output: ALSA Audio output" and a Device menu appears. I select the headphones. When I then save the prefs, the audio switch to the headphones! But here's what's weird: I go back to prefs, change it to "Output: Default" and the headphones keep working. Maybe the ALSA option is actually what is being chosen as the "Default" option, but the Device menu (whose selection is still being used) is still set to the headphones. Anyway, now I need to figure out how to make it work as the default for the whole system.

  Read the article

• My computer freezes irregurarly

  - by Manhim

  My computer started to freeze at irregular times for 3 weeks now. What happens My computer freezes, the video stops. (No graphic glitches, it just stops) Sound keeps playing up to some time (Usually 10-30 seconds) then stops playing. Sometimes, randomly, the screen on my G-15 keyboard flickers and I see caracters not at the right places. Usually happens for about 1-2 seconds and a bit before my computer freezes. I have to keep the power button pressed for 4 seconds to shut my computer down. I still hear my hard drives and fans working. Sometimes it works with no problems for a full day, some other times it just keeps freezing each time I restart my computer and I have to leave it for the rest of the day. Sometimes my mouse freezes for a fraction of a second (Like 0.01 to 0.2 seconds) quite randomly, usually before it freezes. No errors spotted by the "Action center" unlike when I had problems with my last video card on this system (Driver errors). My G-15 LCD screen also freezes. What I did so far I have had similar problems in the past and I had changed my hard drive (It was faulty), so I tested my software RAID-0 array and it was faulty so I changed it. (I reinstalled Windows 7 with this part). I also tested with unplugging my secondary hard drive. My CPU was running at about 100 degree Celsius, I removed the dust between the fans and the heatsink and it's now between 50-60. I ran a CPU stress-test and it didn't freeze during the tests (using Prime95 on all cores) Ran a memory test (using memtest86+) for a single pass and there were no errors. Ran a GPU stress test with ati-tools and furmark and it didn't freeze during the tests. (No artefacts either) I had troubles with my graphic card when I got it, but I think that it got fixed with a driver update. I checked the voltages in my BIOS setup and they all seemed ok (±0.2 I think). I have ran on the computer without problems with Fedora 15 on an external hard drive (Appart that it couldn't load Gnome 3 and was reverting to Gnome 2, didn't want to install drivers since I use it on multiple computers) I used it to backup my files from the raid array to my 1TB hard drive for the reinstallation of Windows. (So the crashes only happenned on Windows) [The external hard drive is plugged directly on a SATA port] I contacted EVGA (My graphic card vendor) and pointed them on this question, I'm looking for an answer. Ran sensors on Fedora 15 and got this output: http://pastebin.com/0BHJnAvu When it happens When I play video games (Mostly) When I play flash games (Second most) When I'm looking at my desktop background (It rarely happens when I have a window open, but it does, sometimes) Specs Windows Seven x64 Home Premium Motherboard: M2N-SLI Deluxe CPU: AMD Phenom 9950 x2 @ 2.6GHz Memory: Kingston 4x2GB Dual Channel (Pretty basic memory sticks) Hard drives: Was 2x250GB (Western digital caviar) in raid-0 + 1TB (WD caviar black), I replaced the raid array with a 750GB (WD caviar black) [Yes I removed the array from the raid configurations] 750W Power supply No overcloking. Ever. There have been some power-downs like 4-5 weeks ago, but the problem didn't start immediately after. (I wasn't home, so my computer got shut-down) My current to-try list Change the thermal paste on my CPU. Change my graphic card with a temporary one and stress the computer. Change my power supply. In this situation, how can I successfully pin-point the current hardware problem? (If it's a hardware problem) Because I don't really have the budget to just forget and replace everything. I also don't really have hardware to test-replace current hardware.

  Read the article

• How to diagnose computer lockups and freezes?

  - by Scott Mitchell

  I built a desktop computer a couple years back with the following specs: CPU: Intel Core 2 Quad Q9300 Yorkfield 2.5GHz 6 MB L2 Cache LGA 775 95W Quad-Core Processor BX80580Q9300 Motherboard: EVGA 122-CK-NF68-T1 LGA 775 NVIDIA nForce 680i SLI ATX Intel Motherboard Video Card: Two EVGA 256-P2-N758-TR GeForce 8600GT SCC 256 MB 128-bit GDDR3 PCI Express x16 SLI Supported Video Card PSU: SeaSonic S12 Energy Plus SS-550HT 550W ATX12V V2.3 / EPS12V V2.91 SLI Certified CrossFire Ready 80 PLUS Certified Active PFC Power Supply Memory: Two G.SKILL 4 GB (2 x 2 GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model F2-6400CL5D-4GBPQ Since its inception, the machine has periodically locked up, the regularity having varied over the years from once a day to once a month. Typically, lockups happen once every few days. By "lockup" I mean my computer just freezes. The screen locks up, I can't move the mouse. Hitting keys on my keyboard that normally turn LEDs on or off on the keyboard (such as Caps Lock) no longer turn the LEDs on or off. If there was music playing at the time of the lockup, noise keeps coming out of the speakers, but it's just the current frequency/note that plays indefinitely. There is no BSOD. When such a lockup occurs I have to do a hard reboot by either turning off the computer or hitting the reset button. I have the most recent version of the NVIDIA hardware drivers, and update them semi-regularly, but that hasn't seemed to help. I am currently using Windows 7 x64, but was previously using Windows Server 2003 x64 and having the same lockup issues. My guess is that it's somehow video driver or motherboard related, but I don't know how to go about diagnosing this problem to narrow down which of the two is the culprit. Additional information re: cooling Regarding cooling... I've not installed any after-market cooling systems aside from two regular fans I scavenged from an older computer. The fan atop the CPU is the one that shipped with it. One of the two scavenged fans I added it located at the bottom tower of the corner, in an attempt to create some airflow from front to back. The second fan is pointed directly at the two video cards. SpeedFan installation and readings Per studiohack's suggestion, I installed SpeedFan, which provided the following temperature readings: GPU: 63C GPU: 65C System: 76C CPU: 64C AUX: 36C Core 0: 78C Core 1: 76C Core 2: 79C Core 3: 79C Update #3: Another Lockup :-( Well, I had another lockup last night. :-( SpeedFan reported the CPU temp at 38 C when it happened, and there was no spike in temperature leading up to the freeze. One thing I notice is that the freeze seems more likely to happen if I am watching a video. In fact, of the last 5 freezes over the past month, 4 of them have been while watching a video on Flickr. Not necessarily the same video, but a video nevertheless. I don't know if this is just coincidence or if it means anything. (As an aside, each night before bedtime my 2 year old daughter sits on my lap and watches some home videos on Flickr and, in the last month, has learned the phrase, "Uh oh, computer broke.") Update #4: MemTest86 and 3DMark06 Test Results: Per suggestions in the comments, I ran the MemTest86 overnight and it cycled through the 8 GB of memory 5 times without error. I also ran the 3DMark06 test without a problem (see my scores at http://3dmark.com/3dm06/15163549). So... what now? :-) Any further suggestions on what to check? Is there some way to get a stack trace or something when the computer locks like that? Resolution I have never did figure out the particular problems, but based on the suggestions here and elsewhere, I'm presuming it was a motherboard issue. In any event, I recently upgraded my system, buying a new motherbeard, PSU, CPU, and RAM, and that new rig has been working splendidly the past several weeks. I am using the same graphic cards as in the old setup, so I think it's safe to reason that they weren't the cause of the problem.

  Read the article

• Why are USB 2.0 devices crashing my system?

  - by BenAlabaster

  Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic baby-ATX motherboard with no identifying markings. CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. There's one stamp on the motherboard that says "Rev.B". On board it has 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. It has an 80Gb Western Digital hard drive freshly formatted and built with Windows XP Professional with Service Pack 3 and all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 crashes the machine as soon as it starts up). It's got a Daytek MV150 15" touch screen running through the VGA and COM1 with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem If I hook any USB 2.0 devices to this machine, it hangs the whole machine and I have to hard boot it to get it back up. Workarounds found I can plug the same devices into the on board USB 1.0 connectors and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions I've tried disabling all the on board devices that I'm not using - such as the on board LAN, the second COM port, the AGP connector etc. through the BIOS in an (perhaps misguided or futile) attempt to reduce the power consumption... I don't think it had any effect but it didn't do any harm. I was wondering if the PSU wattage just isn't enough to drive the USB 2.0 devices; I've seen this suggested but haven't found any confirmation that this could really be an issue - nor have I found a way to work around this issue - if indeed it is one. Any ideas? The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference. I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself. Other thoughts Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine?

  Read the article

• Why does my computer run slowly and freeze sometimes?

  - by Brae

  EDIT I disabled sound in the BIOS, rebooted and it hung. I removed the (previously) faulty HDD, rebooted and it hung. I have managed to get my Realtek audio manager open again after its mysterious disappearance. Subsequently my microphone is now working again, to fix it I had to uninstall audio drivers, disable audio in BIOS, install audio drivers, enable audio in BIOS. Access via network (with faulty HDD in) seems to not be triggering hangs at the moment. I think with the sound problem fixed it might play a little nicer, but I think its still going to hang. If it does, then I'm fairly sure its been narrowed down to the mobo. EDIT Pretty convinced my motherboard is the culprit, because nothing else seems to have any obvious problems (bar the hard drive, which the PC still hangs without it being plugged in) So thank you all for helping, once I get more rep ill up a few of the answers. My PC is doing some weird things... Sometimes when I open up a program, lets say Adobe Photoshop, it will load everything normally, nice and quick no problems and I can use it fine. Other times its a little odd, and it loads the program as if it's only using half of the CPU. It's pretty obvious when it does it, normally the loading screen skims past, but when it does this weird load you see it slowly tick though each thing, and the program itself becomes incredibly slow. Even Google Chrome does it sometimes. Yet when I exit and reopen the program without doing anything else, it typically opens fine without lagging. I think this problem is probably a symptom of something bigger, because of other problems I'm having. Random hangs; no matter what I have open or what I'm doing. My PC will sort of freeze up for a few seconds. If music is playing it will either loop the last second or two, or it will buzz. This only lasts for a few seconds then it returns to normal without having to restart. During this time all programs lock up and freeze, and the mouse and keyboard are useless. I am also having a weird issue with my audio jacks, without touching my PC at all, sometimes I will see a popup saying that I have unplugged something or plugged something in, neither of which has actually happened. Pretty sure this is cause by the motherboard. I recently had a 'Pink Screen of Death' (yes pink) which pointed to my audio drivers. The lockups seem to happen with some consistency when someone is accessing my shared files via my home LAN. Which leads me to believe either one of my hard drives is acting up or more likely the controller. One of my drives had a bit of a crash before, I used Spinrite and managed to recover my stuff and now the drive appears to be working okay. This is possibly adding to the problems. My best guess is something has gone wrong with my motherboard, possibly a power issue or a chip has died, I really don't know. So what I would like to know is: Have I have missed some obvious diagnostic to help figure out what it is, or should I just bite the bullet and assume its my motherboard acting up and buy a new system? dxdiag[64-bit] - http://pastebin.com/G30kb2TL PSOD (minidump) - http://pastebin.com/aZsv0H56 HWiNFO64 (system info / specs) - http://pastebin.com/X6h3K8g6

  Read the article

< Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >