Search Results

Search found 5874 results on 235 pages for 'idle mind'.

Page 203/235 | < Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >

• fd partitions gone from 2 discs, md happy with it and resyncs. How to recover ?

  - by d0nd

  Hey gurus, need some help badly with this one. I run a server with a 6Tb md raid5 volume built over 7*1Tb disks. I've had to shut down the server lately and when it went back up, 2 out of the 7 disks used for the raid volume had lost its conf : dmesg : [ 10.184167] sda: sda1 sda2 sda3 // System disk [ 10.202072] sdb: sdb1 [ 10.210073] sdc: sdc1 [ 10.222073] sdd: sdd1 [ 10.229330] sde: sde1 [ 10.239449] sdf: sdf1 [ 11.099896] sdg: unknown partition table [ 11.255641] sdh: unknown partition table All 7 disks have same geometry and were configured alike : dmesg : Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect All 7 disks (sdb1, sdc1, sdd1, sde1, sdf1, sdg1, sdh1) were used in a md raid5 xfs volume. When booting, md, which was (obviously) out of sync kicked in and automatically started rebuilding over the 7 disks, including the two "faulty" ones; xfs tried to do some shenanigans as well: dmesg : [ 19.566941] md: md0 stopped. [ 19.817038] md: bind<sdc1> [ 19.817339] md: bind<sdd1> [ 19.817465] md: bind<sde1> [ 19.817739] md: bind<sdf1> [ 19.817917] md: bind<sdh> [ 19.818079] md: bind<sdg> [ 19.818198] md: bind<sdb1> [ 19.818248] md: md0: raid array is not clean -- starting background reconstruction [ 19.825259] raid5: device sdb1 operational as raid disk 0 [ 19.825261] raid5: device sdg operational as raid disk 6 [ 19.825262] raid5: device sdh operational as raid disk 5 [ 19.825264] raid5: device sdf1 operational as raid disk 4 [ 19.825265] raid5: device sde1 operational as raid disk 3 [ 19.825267] raid5: device sdd1 operational as raid disk 2 [ 19.825268] raid5: device sdc1 operational as raid disk 1 [ 19.825665] raid5: allocated 7334kB for md0 [ 19.825667] raid5: raid level 5 set md0 active with 7 out of 7 devices, algorithm 2 [ 19.825669] RAID5 conf printout: [ 19.825670] --- rd:7 wd:7 [ 19.825671] disk 0, o:1, dev:sdb1 [ 19.825672] disk 1, o:1, dev:sdc1 [ 19.825673] disk 2, o:1, dev:sdd1 [ 19.825675] disk 3, o:1, dev:sde1 [ 19.825676] disk 4, o:1, dev:sdf1 [ 19.825677] disk 5, o:1, dev:sdh [ 19.825679] disk 6, o:1, dev:sdg [ 19.899787] PM: Starting manual resume from disk [ 28.663228] Filesystem "md0": Disabling barriers, not supported by the underlying device [ 28.663228] XFS mounting filesystem md0 [ 28.884433] md: resync of RAID array md0 [ 28.884433] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [ 28.884433] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. [ 28.884433] md: using 128k window, over a total of 976759936 blocks. [ 29.025980] Starting XFS recovery on filesystem: md0 (logdev: internal) [ 32.680486] XFS: xlog_recover_process_data: bad clientid [ 32.680495] XFS: log mount/recovery failed: error 5 [ 32.682773] XFS: log mount failed I ran fdisk and flagged sdg1 and sdh1 as fd. I tried to reassemble the array but it didnt work: no matter what was in mdadm.conf, it still uses sdg and sdh instead of sdg1 and sdh1. I checked in /dev and I see no sdg1 and and sdh1, shich explains why it wont use it. I just don't know why those partitions are gone from /dev and how to readd those... blkid : /dev/sda1: LABEL="boot" UUID="519790ae-32fe-4c15-a7f6-f1bea8139409" TYPE="ext2" /dev/sda2: TYPE="swap" /dev/sda3: LABEL="root" UUID="91390d23-ed31-4af0-917e-e599457f6155" TYPE="ext3" /dev/sdb1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdc1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdd1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sde1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdf1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdg: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdh: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" fdisk -l : Disk /dev/sda: 40.0 GB, 40020664320 bytes 255 heads, 63 sectors/track, 4865 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8c878c87 Device Boot Start End Blocks Id System /dev/sda1 * 1 12 96358+ 83 Linux /dev/sda2 13 134 979965 82 Linux swap / Solaris /dev/sda3 135 4865 38001757+ 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc9bdc1e9 Device Boot Start End Blocks Id System /dev/sdc1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xcc356c30 Device Boot Start End Blocks Id System /dev/sdd1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xe87f7a3d Device Boot Start End Blocks Id System /dev/sde1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdf: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xb17a2d22 Device Boot Start End Blocks Id System /dev/sdf1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdg: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8f3bce61 Device Boot Start End Blocks Id System /dev/sdg1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdh: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xa98062ce Device Boot Start End Blocks Id System /dev/sdh1 1 121601 976760001 fd Linux raid autodetect I really dont know what happened nor how to recover from this mess. Needless to say the 5TB or so worth of data sitting on those disks are very valuable to me... Any idea any one? Did anybody ever experienced a similar situation or know how to recover from it ? Can someone help me? I'm really desperate... :x

  Read the article

• VFS: file-max limit 1231582 reached

  - by Rick Koshi

  I'm running a Linux 2.6.36 kernel, and I'm seeing some random errors. Things like ls: error while loading shared libraries: libpthread.so.0: cannot open shared object file: Error 23 Yes, my system can't consistently run an 'ls' command. :( I note several errors in my dmesg output: # dmesg | tail [2808967.543203] EXT4-fs (sda3): re-mounted. Opts: (null) [2837776.220605] xv[14450] general protection ip:7f20c20c6ac6 sp:7fff3641b368 error:0 in libpng14.so.14.4.0[7f20c20a9000+29000] [4931344.685302] EXT4-fs (md16): re-mounted. Opts: (null) [4982666.631444] VFS: file-max limit 1231582 reached [4982666.764240] VFS: file-max limit 1231582 reached [4982767.360574] VFS: file-max limit 1231582 reached [4982901.904628] VFS: file-max limit 1231582 reached [4982964.930556] VFS: file-max limit 1231582 reached [4982966.352170] VFS: file-max limit 1231582 reached [4982966.649195] top[31095]: segfault at 14 ip 00007fd6ace42700 sp 00007fff20746530 error 6 in libproc-3.2.8.so[7fd6ace3b000+e000] Obviously, the file-max errors look suspicious, being clustered together and recent. # cat /proc/sys/fs/file-max 1231582 # cat /proc/sys/fs/file-nr 1231712 0 1231582 That also looks a bit odd to me, but the thing is, there's no way I have 1.2 million files open on this system. I'm the only one using it, and it's not visible to anyone outside the local network. # lsof | wc 16046 148253 1882901 # ps -ef | wc 574 6104 44260 I saw some documentation saying: file-max & file-nr: The kernel allocates file handles dynamically, but as yet it doesn't free them again. The value in file-max denotes the maximum number of file- handles that the Linux kernel will allocate. When you get lots of error messages about running out of file handles, you might want to increase this limit. Historically, the three values in file-nr denoted the number of allocated file handles, the number of allocated but unused file handles, and the maximum number of file handles. Linux 2.6 always reports 0 as the number of free file handles -- this is not an error, it just means that the number of allocated file handles exactly matches the number of used file handles. Attempts to allocate more file descriptors than file-max are reported with printk, look for "VFS: file-max limit reached". My first reading of this is that the kernel basically has a built-in file descriptor leak, but I find that very hard to believe. It would imply that any system in active use needs to be rebooted every so often to free up the file descriptors. As I said, I can't believe this would be true, since it's normal to me to have Linux systems stay up for months (even years) at a time. On the other hand, I also can't believe that my nearly-idle system is holding over a million files open. Does anyone have any ideas, either for fixes or further diagnosis? I could, of course, just reboot the system, but I don't want this to be a recurring problem every few weeks. As a stopgap measure, I've quit Firefox, which was accounting for almost 2000 lines of lsof output (!) even though I only had one window open, and now I can run 'ls' again, but I doubt that will fix the problem for long. (edit: Oops, spoke too soon. By the time I finished typing out this question, the symptom was/is back) Thanks in advance for any help. And another update: My system was basically unusable, so I decided I had no option but to reboot. But before I did, I carefully quit one process at a time, checking /proc/sys/fs/file-nr after each termination. I found that, predictably, the number of open files gradually went down as I closed things down. Unfortunately, it wasn't a large effect. Yes, I was able to clear up 5000-10000 open files, but there were still over 1.2 million left. I shut down just about everything. All interactive shells, except for the one ssh I left open to finish closing down, httpd, even nfs service. Basically everything in the process table that wasn't a kernel process, and there were still an appalling number of files apparently left open. After the reboot, I found that /proc/sys/fs/file-nr showed about 2000 files open, which is much more reasonable. Starting up 2 Xvnc sessions as usual, along with the dozen or so monitoring windows I like to keep open, brought the total up to about 4000 files. I can see nothing wrong with that, of course, but I've obviously failed to identify the root cause. I'm still looking for ideas, since I definitely expect it to happen again. And another update, the next day: I watched the system carefully, and discovered that /proc/sys/fs/file-nr showed a growth of about 900 open files per hour. I shut down the system's only NFS client for the night, and the growth stopped. Mind you, it didn't free up the resources, but it did at least stop consuming more. Is this a known bug with NFS? I'll be bringing the NFS client back online today, and I'll narrow it down further. If anyone is familiar with this behavior, feel free to jump in with "Yeah, NFS4 has this problem, go back to NFS3" or something like that.

  Read the article

• Planning trunk capacity for multiple GbE switches

  - by wuckachucka

  Without measuring throughput (it's at the top of the list; this is just theoretical), I want to know the most standard method for trunking VLANs on multiple Gigabit (GbE) switches to a core Layer 3 GbE switch. Say you have three VLANs: VLAN10 (10.0.0.0/24) Servers: your typical Windows DC/file server, Exchange, and an Accounting/SQL server. VLAN20: (10.0.1.0/24) Sales: needs access to everything on VLAN10; doesn't need access to VLAN30 and vice-versa. VLAN20: (10.0.1.0/24) Support: needs access to everything on VLAN10; doesn't need access to VLAN20 and vice-versa. Here's how I think this should work in my head: Switch #1: Ports 2-20 are assigned to VLAN20; all the Sales workstations and printers are connected here. Optional 10GbE combo port #1 is trunked to L3 switch's 10 GbE combo port #1. Switch #2: Ports 2-20 are assigned to VLAN30; all the Support workstations and printers are connected here. Optional 10GbE combo port #1 is trunked to L3 switch's 10 GbE combo port #2. Core L3 switch: Ports 2-10 are assigned to VLAN10; all three servers are connected here. With a standard 10/100 x 24 switch, it'll usually come with one or two 1 GbE uplink ports; carrying over this logic to a 10/100/1000 x 24, the "optional" 10 GbE combo ports that most higher-end switches can get shouldn't really be an option. Keep in mind I haven't tested anything yet, I'm primarily moving in this direction for growth (don't want to buy 10/100 switches and have to replace those within a couple of years) and security (being able to control access between VLANs with L3 routing/packet filtering ACLs). Does this sound right? Do I really need the 10 GbE ports? It seems very non-standard and expensive, but it "feels" right when you think about 40 or 50 workstations trunking up to the L3 switch over 1 GbE standard ports. If say 20 workstations want to download a 10 GB image from the servers concurrently, wouldn't the trunk be the bottleneck? At least if the trunk was 10 GbE, you'd have 10x1GbE nodes being able to reach their theoretical max. What about switch stacking? Some of the D-Links I've been looking at have HDMI interfaces for stacking. As far as I know, stacking two switches creates one logical switch, but is this just for management I/O or does the switches use the (assuming it's HDMI 1.3) 10.2 Gbps for carrying data back and forth?

  Read the article

• Ubuntu: Multiple NICs, one used only for Wake-On-LAN

  - by jcwx86

  This is similar to some other questions, but I have a specific need which is not covered in the other questions. I have an Ubuntu server (11.10) with two NICs. One is built into the motherboard and the other is a PCI express card. I want to have my server connected to the internet via my NAT router and also have it able to wake from suspend using a Magic Packet (henceforth referred to as Wake-On-LAN, WOL). I can't do this with just one of the NICs because each has an issue - the built-in NIC will crash the system if it is placed under heavy load (typically downloading data), whilst the PCI express NIC will crash the system if it is used for WOL. I have spent some time investigating these individual problems, to no avail. My plan is thus: use the built-in NIC solely for WOL, and use the PCI express card for all other network communication except WOL. Since I send the WOL Magic Packet to a specific MAC address, there is no danger of hitting the wrong NIC, but there is a danger of using the built-in NIC for general network access, overloading it and crashing the system. Both NICs are wired to the same LAN with address space 192.168.0.0/24. The built-in ethernet card is set to have interface name eth1 and the PCI express card is eth0 in Ubuntu's udev persistent rules (so they stay the same upon reboot). I have been trying to set this up with the /etc/network/interfaces file. Here is where I am currently: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 auto eth1 iface eth1 inet static address 192.168.0.254 netmask 255.255.255.0 I think by not specifying a gateway for eth1, I prevent it being used for outgoing requests. I don't mind if it can be reached on 192.168.0.254 on the LAN, i.e. via SSH -- it's IP is irrelevant to WOL, which is based on MAC addresses -- I just don't want it to be used to access internet resources. My kernel routing table (from route -n) is Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 My question is this: Is this sufficient for what I want to achieve? My research has thrown up the idea of using static routing to specify that eth1 should only be used for WOL on the local network, but I'm not sure this is necessary. I have been monitoring the activity of the interfaces using iptraf and it seems like eth0 takes the vast majority of the packets, though I am not sure that this will be consistent based on my configuration. Given that if I mess up the configuration, my system will likely crash, it is important to me to have this set up correctly!

  Read the article

• Baseline / Benchmark Physical and virtual server performance

  - by EyeonTech

  I am setting up a new server and there are some options. I want to perform some benchmarks and I need your help in determining the best tools and if possible run pre-configured benchmarks designed for SQL servers on Windows Server 2008/2012. Step 1. Run a performance monitor on the current Live SQL server (Windows Server 2008 Virtual machine running on ESXi. New server Hardware rundown: Intel® Server System R1304BTLSHBN - 1U Rack, LGA1155 http://ark.intel.com/products/53559/Intel-Server-System-R1304BTLSHBN Intel Xeon E3-1270V2 2x Intel SSD 330 Series 240GB 2.5in SATA 6Gb/s 25nm 1x WD 2TB WD2002FAEX 2TB 64M SATA3 CAVIAR BLACK 4x 8GB 1333MHz DDR3 ECC CL9 DIMM There are several options for configurations and I want to benchmark some of them and share the results. Option 1. Configure 2x SSDs at RAID 0. Install Windows Server 2008 directly to the 2TB WD Caviar HDD. Store Database files on the RAID 0 Volume. Benchmark the OS direct on the hardware as an SQL Server. Store SQL Backup databases on the 2TB WD Caviar HDD. Option 2. Configure 2x SSDs at RAID 0. Install Windows Server 2012 directly to the 2TB WD Caviar HDD. Install Hyper-V. Install the SQL Server (Server 2008) as a virtual machine. Store the Virtual Hard Disks on the SSDs. Option 3. Configure 2x SSDs at RAID 0. Install VMWare ESXi on a partition of the 2TB WD Caviar HDD. Install the SQL Server (Server 2008) as a virtual machine. Store the Virtual Hard Disks on the SSDs. I have a few tools in mind from http://technet.microsoft.com/en-us/library/cc768530(v=bts.10).aspx. Any tools with pre-configured test would be fantastic. Specifically if there are pre-configured perfmon sets avaliable. Any opinions on the setup to gain the best results is welcome. Thanks in advance.

  Read the article

• change owner/uid of mount point upon mount

  - by Shiplu

  The scenario is like this. Bob has a computer. It crashed. Now he only has the hdd. The hdd is in ext3 format. He go to his office and told the sys admin John to mount this hdd and put the mount point in his home directory. John used the following fstab entries. # Bobs harddisk /media/TAPE4/Bobs-hdd.img /home/bob/myhdd/windows ntfs ro,loop,offset=32256 0 0 /media/TAPE4/Bobs-hdd.img /home/bob/myhdd/linux ext3 ro,loop,offset=14048810496 0 0 /media/TAPE4/Bobs-hdd.img /home/bob/myhdd/extra ntfs ro,loop,offset=28015335936 0 0 Bob was happy. He could access his old extra and windows. Specially the Documents and Settings in windows was helpful for him. But he found a problem. He is a web developer and all his websites are in linux/home/bob/public_html directory. When he tried to access that public_html directory he got permission_denied. He executed ls -lh he saw this. drwxr-xr-x 2 john john 4.0K Nov 9 2011 Desktop drwxr-xr-x 3 john john 4.0K Aug 12 2011 Documents drwxr-xr-x 3 john john 4.0K Aug 21 2011 public_html He contacted John thinking he might be mistakenly did this. But John couldn't find a way why this happend? Then one thing came into his mind file system hardly store username. They store uids. So he executed ls -ln drwxr-xr-x 2 1000 1000 4096 Nov 9 2011 Desktop drwxr-xr-x 3 1000 1000 4096 Aug 12 2011 Documents drwxr-xr-x 3 1000 1000 4096 Aug 21 2011 public_html John thinks 1000 is the first uid on a linux system. As he is the admin of the current system. He created his account first. so Johns uid was 1000. Bob also setup his private system and crated his account first. So Bobs uid was 1000 too. So thats an expected behavior. But problem remains. How can Bob access those websites in public_html?

  Read the article

• Microsoft Office 2003 document (Excel and Word) intermitently, takes 30 seconds to load

  - by Julio Nobre

  I am trying to figure out why a simple .XLS EXCEL workbook is taking, randomly, 30 seconds to open. Before answering: Please, bear mind the following: Problem symptoms Hanging is intermitent and it takes exactly 30 seconds; During hanging there is no cpu or disk activity; It only happens during document load. Every runs smooth after that; Windows Explorer.exe hangs on folder, but all other folders, system and applications are still responsive; There are no consecutive hangings. I have to wait for while to reproduce this behaviour; All samples documents are located on a local drive (C:\BPI); The no document has has macros and have any addins usage; The problem does occurs on others files extensions like .PDF, for example; Office 2003 is being used for several years; The computer is running Windows XP; Computer has several network mapped drives, all addressed to main file server; Recently, main fileserver was replaced by Windows 2011 SBS Standard Edition What I have done so far I have traced machine Explorer.exe, using Process Monitor, added Duration column, and filtered by Duration 1. That's is how I found that hanging was taking exactly 30 seconds. For further information, please refer to Oliver Salzburg tutorial. Using Process Monitor, I have also figured out than five operations were taking most of sample collecting duration. Looking at sample image below, column Operation below you will notice that one single operation was taking 29 seconds; I have tried different documents (.xls and .doc), all of them smaller than 30 KB; I have, temporarily, removed all shortcuts on User Document's folder that were pointing to network drives or shares; I have runned CCleaner to fix registry issues; I made sure that there were no external links on tested workbook or word documents; I have reproduced this behaviour for hours; I have extensivelly researched for hours on the web; Process Monitor's collected and filtered data

  Read the article

• New monitor connected to HDMI adaptor doesn't show output after booting

  - by Paul

  Hello out there in the multiple monitors’ world. I am a very old newbie in your world and need help. I just purchased a new Asus VH236H monitor and hooked it up the HDMI port of an ATI Radeon HD4300 / 4500 Series display adaptor. I left the old Princeton LCD19 (TMDS) hooked up to the DVI port of the same display adaptor. Both monitors displayed the boot sequence, after I fired good old Sarastro2 (Asus P5Q Pro Turbo – Dual Core E5300 – 2.60 GHz) up. The Asus lacked one half of a second behind the Princeton until the Windows 7 Ultimate SP 1 boot up was complete. Then the Asus displayed “HDMI NO SIGNAL” and went into hibernation. The Princeton stayed lit up as before. Both monitors are displayed on the “Screen Resolution Setup Display” and I plaid around with them for a while. The only thing I accomplished was to shove the desktop icons from the Princeton to the still hibernating Asus. The “Multiple displays:” is set to “Extend these displays”, the Orientation is “Landscape” and the Resolutions are set on both to the “recommended” one. Both monitors show that they work properly in the advanced Properties display. What am I doing wrong, what am I missing? Never mind the opinions about the different resolutions of the two monitors. I always can unhook the Princeton and give it to a Goodwill Store if I do not like the setup. I just would like to make it work. Any constructive help is very much appreciated, Thank you. Thank you Anees Bakrain Only the ATI Radeon HD 4300/4500 Series adapter is displayed in the Device Manager, for that reason I have to assume that the onboard display adaptor is not active. All 40 drivers of Sarastro2 are up to date and the HDMI cable can not be the problem because both monitors displayed the boot sequence up to the moment when Windows 7 was loaded completely. This was the moment, when the Asus monitor lost its signal. Both connectors, HDMI and DVI are connected and removing the DVI connector would not solve my problem of running both monitors simultaneously. However, your suggestions shifted my seventy one year old brain into the next gear. The only question remaining is; “Why the signals to the Asus monitor stop after the sequence is complete”. The ATI Radeon HD 4300/4500 Series adapter seems to be capable of sending simultaneous HDMI and DVI signals, what is done during the boot sequence. Why do the signals change after the boot sequence is complete is the key question or der springende Punkt? Is this a correct assumption slhck?

  Read the article

• A dusty server room

  - by pauska

  Here's the story.. The owners of the building we lease office space from decided to do a renovation of the exterior. This involved in some pretty heavy work at the level where our server room is, including exchanging windows wich are fit inside a concrete wall. My red alert went off when I heard that they were going to do the same thing with our server room (yes, our server room has a window. We're a small shop with 3 racks. The window is secured with steel bars.) I explicity told the contractor that they need to put up a temporarily wall between our racks and the original wall - and to make sure that the temporary wall is 100 % air and water-tight. They promised to do so. The temporary wall has a small door in it, so that workers can go in/out through the day (through our server room, wich was the only option....). On several occasions I could find the small door half-way shut while working evenings/nights. I locked the door, and thought that they would hopefully get the point soon and keep the door shut. I even gave a electrician a mouthful when I saw that he didn't close the door properly. By this point - I bet that most of you get a picture of what happened. Yes, they probably left the door open while drilling in the concrete. I present you our 4 weeks old EMC VNX: I'll even put in a little bonus, here is the APC UPS one rack further away from the temporary wall. See the nice little landing strip from my finger? What should I do? The only thing that comes to mind is to either call all our suppliers (EMC, HP, Dell, Cisco) and get them to send technicians to check out all the gear in the server room, or get some kind of certified 3rd-party consulant to check all of it. Would you run production systems on this gear? How long? Edit: I should also note that our aircondition isn't exactly enterprise-grade, given the nature of our small room. It's just a single inverter, wich have failed one time before I started working here (failed inverters usually leads to water dripping out).

  Read the article

• DCHP and Router load testing

  - by John H

  I manage a campground wifi network with an average of 10 - 60 active users. I have encountered issues where the router starts acting flaky (failing to assign DHCP or failing to pass traffic) without any clear warning (low cpu utilization, etc). I upgraded the router a couple times and ended up with a Netgear ProSafe VPN router that seems to be handling the traffic. The interesting thing is that the Netgear has lower specs than the Buffalo router it replaced, indicating the issue is with the DD-WRT firmware. While I'll be pursuing this issue on the dd-wrt forums, I need a way to test routers. My vision is having 1-2 computers connected on the LAN side and 1-2 computers connected on the WAN side. I want the LAN computers to be generating various type of traffic and connections, as well as requesting DCHP addresses. A few notes: The wireless aspect should be a non-issue. Most clients would connect to a wireless bridge and come into the router through a network cable. I had a monitoring server with Nagios running check_dhcp against the router. This server was connected directly by a network cable, eliminating wifi bridges and other devices from the equation. This question is somewhat related, but not exactly: Load testing wireless LANs I am going to look at IxChariot. While I'd ideally like to use a 1 computer on each side running Linux and preferably free software, I can entertain running Windows, multiple computers, or non-free software. Total bandwidth doesn't seem to be the issue. I can transfer large files all day. Even on the busiest days, the users seemed to only pull ~5Mbps. There is very little "LAN to LAN traffic" and most of it might never have reached the main router. The issue I need to test for seems to be tied to active users, or more appropriately, active sessions. I know active users or active clients is a meaningless term from a router standpoint and wouldn't mind having more appropriate terms to use. Summary: I need a way to test a routers ability in handling traffic from a large number of clients. My current strategy is to purchase a router, deploy it, and see how it fails in the live environment.

  Read the article

• Routing RFC1918 addresses through dd-wrt via a switch

  - by espenfjo

  I am a bit stuck with an experiment of mine. I have a network looking somewhat like this. | Internet | | ---- |Switch| ---- | | Server w/pub IP | DD-WRT router 192.168.1.1 | | RFC1918 clients 192.168.1.0/24 What I want is for the RFC1918 clients to speak directly with each others. On the server with the public IP I have this route: 192.168.1.0/24 dev eth0 scope link and can see that packets are infact reaching the dd-wrt router for 192.168.1.1, even though if I get no answer. Trying to reach one of the RFC1918 clients from the public IP server will get no result, as the dd-wrt router is not announcing that network on to its external interface (arp who-has 192.168.1.107 tell xxx.xxx.xxx.xxx, but no answer). The router being an WLAN dd-wrt router has of course a load of routes, VLANs and interfaces: xxx.xxx.xxx.1 dev vlan2 scope link 192.168.1.0/24 dev br0 proto kernel scope link src 192.168.1.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.244 84.215.64.0/18 dev vlan2 proto kernel scope link src xxx.xxx.xxx.xxx 169.254.0.0/16 dev br0 proto kernel scope link src 169.254.255.1 127.0.0.0/8 dev lo scope link 0.0.0.0 via xxx.xxx.xxx.1 dev vlan2 xxx.xxx.xxx.xxx being the public IP, and xxx.xxx.xxx.1 being the default route for the public IP. I am not sure where to continue with this. I would recon that I both need routing on the dd-wrt router, as well as some iptables magic? Why do something this complex? Why not ;) Also, do not mind that "Internet" can get RFC1918 traffic, it wont go outside of the walls. EDIT 1: Following the tip from stew I do indeed get the correct ARP flowing. And adding an iptables rule for allowing traffic from that specific public IPd machine I get traffic between the systems! Oddly enough though, the speed I get from Server w/pub IP - RFC1918 clients are the same as if the traffic were routed out onto the Internet and back. Edit 2: Ok, disconnecting the external Internet connection will still give the same, crappy transfer speed. So it has to be something else. Edit 3: Ok, I guess there are other reasons for this crappy speed. Case closed. :)

  Read the article

• Need advice on which PCI SATA Controller Card to Purchase

  - by Matt1776

  I have a major issue with the build of a machine I am trying to get up and running. My goal is to create a file server that will service the needs of my software development, personal media storage and streaming/media server needs, as well as provide a strong platform for backing up all this data in a routine, cron-job oriented German efficiency sort of way. The issue is a simple one - all my drives are SATA drives and my motherboard controller only contains 4 ports. Solving the issue has proven to be an unmitigated nightmare. I would like advice on the purchase of the following: 4 Port internal SATA / 2 Port external eSATA PCI SATA Controller Card that has the following features and/or advantages: It must function. If I plug it in and attach drives, I expect my system to still make it to the Operating System login screen. It must function on CentOS, and I mean it must function WELL and with MINIMAL hassle. If hassle is unavoidable, there shall be CLEAR CUT and EASY TO FOLLOW instructions on how to install drivers and other supporting software. I do not need nor want fakeRAID - I will be setting up any RAID configurations from within the operating system. Now, if I am able to find such a mythical device, I would be eternally grateful to whomever would be able to point me in the right direction, a direction which I assume will be paved with yellow bricks. I am prepared to pay a considerable sum of money (as SATA controller cards go) and so paying anywhere between 60 to 120 dollars will not be an issue whatsoever. Does such a magical device exist? The following link shows an "example" of the type of thing I am looking for, however, I have no way of verifying that once I plug this baby in that my system will still continue to function once I've attached the drives, or that once I've made it to the OS, I will be able to install whatever drivers or software programs I need to make it work with relative ease. It doesn't have to be dog-shit simple, but it cannot involve kernels or brain surgery. http://www.amazon.com/gp/product/B00552PLN4/ref=pd_lpo_k2_dp_sr_1?pf_rd_p=486539851&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=B003GSGMPU&pf_rd_m=ATVPDKIKX0DER&pf_rd_r=1HJG60XTZFJ48Z173HKY So does anyone have a suggestion regarding the subject I am asking about? PCI SATA Controller Cards? It would help if you've had experience with the component before - that is after all why I am asking here - for those who have had experience that I do not have. Bear in mind that this is for a home setup and that I do not have a company credit card. I have a budget with a 'relative' upper limit of about $150.00.

  Read the article

• Is Samba Server what I'm looking for, and if so, what do I need? (currently on DD-WRT Micro)

  - by Anthony

  I am really confused as to what Samba actually does and how it works. Here's what I'm hoping it does: I set up a Samba server on my LAN, and everyone will be able to see each other's shared files and swap them. But some of the documentation makes it sound like it will just allow Mac/Linux computers to see Windows computers. Other bits of the documentation make it sound more like a local server, where a Linux machine would install Samba and they would see everyone and be visible to everyone, but that won't change if anybody else can see each other. While still other things I've read make it seem more like a file-server, where everyone sees each other but file transfers are not peer-to-peer but instead need a host disk for files to act as go between. So, assuming I'm even in the right ballpark of what Samba does in terms of my goal of total cross-visibility on the network, I am left with needing to know what I'd need to set up the server and whether it can be done and is worth it... DD-WRT's article on Samba is a bit ambiguous. One second it sounds as if I can run the server on micro as long as it's set up on a usb drive, but then it also sounds like micro can't run it at all, etc. If I can run it from a usb-connected drive, I still need to know if the files are actually stored on that drive. The dd-wrt article mentions: You can run a Samba server on your main computer and run a client on your router (thus gaining writable storage for the router) or you can use Samba to share a drive connected (typically by USB) to the router among all the computers connected to your network. That one part "to share a drive...among all the computers" makes it sound like the only benefit I get from Samba is a share drive that any OS on the network can see, but they still won't see each other. But I'm very hopeful I'm misreading this. If the computers can see each other but still need the disk, how much space is generally a good idea? I'm basing this on the idea that the drive is a temporary store point. Obviously I'd have to get a drive big enough to store everything people wanted to share if the drive is a full-on file server. If I do have this all wrong, is there any software that achieves what I have in mind? Something that connects to the main router to bridge all clients?

  Read the article

• Cisco: unable to negotiate IP using IPCP with Windows server

  - by lnk

  I am connecting to Windows server using PPP (for vpn), I establish connection but server does not respond me for my address requests: *Mar 23 00:40:06.055: Vi1 MS-CHAP-V2: I CHALLENGE id 0 len 25 from "MSDC" *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using hostname from interface CHAP *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using password from interface CHAP *Mar 23 00:40:06.067: Vi1 MS-CHAP-V2: O RESPONSE id 0 len 69 from "XXX" *Mar 23 00:40:06.087: Vi1 PPP: I pkt type 0xC223, datagramsize 50 link[ppp] *Mar 23 00:40:06.087: Vi1 MS-CHAP-V2: I SUCCESS id 0 len 46 msg is "S=XXX" *Mar 23 00:40:06.087: Vi1 MS CHAP V2 No Password found for : XXX *Mar 23 00:40:06.091: Vi1 MS CHAP V2 Check AuthenticatorResponse Success for : XXX *Mar 23 00:40:06.091: Vi1 IPCP: O CONFREQ [Closed] id 1 len 20 *Mar 23 00:40:06.091: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:06.091: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:07.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up *Mar 23 00:40:07.091: Vi1 LCP: O ECHOREQ [Open] id 1 len 12 magic 0x194CAFCF *Mar 23 00:40:07.103: Vi1 LCP-FS: I ECHOREP [Open] id 1 len 12 magic 0x361B62E5 *Mar 23 00:40:07.103: Vi1 LCP-FS: Received id 1, sent id 1, line up *Mar 23 00:40:08.083: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:08.083: Vi1 IPCP: O CONFREQ [REQsent] id 2 len 20 *Mar 23 00:40:08.083: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:08.083: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:10.099: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:10.099: Vi1 IPCP: O CONFREQ [REQsent] id 3 len 20 *Mar 23 00:40:10.099: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:10.099: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.115: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:12.115: Vi1 IPCP: O CONFREQ [REQsent] id 4 len 20 *Mar 23 00:40:12.115: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:12.115: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.211: Vi1 LCP: O ECHOREQ [Open] id 2 len 12 magic 0x194CAFCF *Mar 23 00:40:12.219: Vi1 LCP-FS: I ECHOREP [Open] id 2 len 12 magic 0x361B62E5 *Mar 23 00:40:12.219: Vi1 LCP-FS: Received id 2, sent id 2, line up *Mar 23 00:40:14.131: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:14.131: Vi1 IPCP: O CONFREQ [REQsent] id 5 len 20 *Mar 23 00:40:14.131: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:14.131: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:16.147: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:16.147: Vi1 IPCP: O CONFREQ [REQsent] id 6 len 20 *Mar 23 00:40:16.147: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:16.147: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:17.331: Vi1 LCP: O ECHOREQ [Open] id 3 len 12 magic 0x194CAFCF *Mar 23 00:40:17.343: Vi1 LCP-FS: I ECHOREP [Open] id 3 len 12 magic 0x361B62E5 *Mar 23 00:40:17.343: Vi1 LCP-FS: Received id 3, sent id 3, line up You see: My router asks for address, but only keepalives are on line. But the same server works with windows client!! ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption service internal ! hostname Router ! boot-start-marker boot-end-marker ! ! no aaa new-model ! resource policy ! ip subnet-zero ! ! ip cef vpdn enable ! vpdn-group pptp request-dialin protocol pptp pool-member 1 initiate-to ip XXXX ! ! ! ! ! ! ! bridge irb ! ! interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface Dot11Radio0 no ip address shutdown speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Vlan1 no ip address bridge-group 1 ! interface Dialer0 ip address negotiated encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer string XXX dialer persistent dialer vpdn dialer-group 1 keepalive 5 3 no cdp enable ppp authentication ms-chap-v2 optional ppp eap refuse ppp chap hostname XXX ppp chap password 0 XXX ppp ipcp mask request ppp ipcp ignore-map ppp ipcp address accept ! interface BVI1 mac-address XXX.XXX.XXX ip address dhcp ! ip classless ip route 172.0.0.0 255.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! dialer-list 1 protocol ip permit ! control-plane ! bridge 1 protocol vlan-bridge bridge 1 route ip ! line con 0 no modem enable line aux 0 line vty 0 4 login ! scheduler max-task-time 5000 end

  Read the article

• local user cannot access vsftpd server

  - by Zloy Smiertniy

  I'm currently running a vsftpd server and I added the necessary configurations in vsftpd.conf so that local users can use clients like FileZilla to manage their homes in a server. I found out that only users in the sudoers list access without a problem only they can't download the files, but users that are not sudoers cannot even access their homes from a client but they can access by a web browser using the FTP protocol and they can only access their home directories (as intented) Im running a fedora 14 on my server and my vsftpd.conf looks like this: # Example config file /etc/vsftpd/vsftpd.conf # # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=NO # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. #anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. #anon_mkdir_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log #xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=YES # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. ascii_upload_enable=YES ascii_download_enable=YES # # You may fully customise the login banner string: ftpd_banner=Welcome to GAMBITA FTP service # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). chroot_local_user=YES chroot_list_enable=YES # (default follows) chroot_list_file=/etc/vsftpd/chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd with two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES use_localtime=YES Anyone has an idea of what might be happening? Nothing concerning vsftpd is written in any log

  Read the article

• Monitoring the status of accounts with IT Service providers (ISP, Domain Registrar etc.)

  - by Sholom

  Hi All, Short version: You have software that tells you when your servers power-outlet is down. It monitors multiple servers from one management console, alerts you when something is wrong etc. Does anyone know of software that will let me take the same approach to monitor if the money-outlet (the bill!) is down (not paid) to my IT Services providers (ISP, Domain Registrar, MX Backup service etc). I need a top down, centrally managed service that is capable of sending out alerts. Just like the one that monitors my own exchange server etc. I don't mind if i have to manually enter every payment. Long version: Our very likable but absent minded bookkeeper keeps neglecting to pay our IT vendors on time. Just this past week our internet service was disconnected. Same could happen to many other mission critical accounts (domain registrar, backup MX, anti-virus license, HackerSafe (McAfee secure) service and even an 800 number to name a few). As the sysadmin, i monitor my severs to make sure they are plugged into the power-outlet. I believe i should also monitor my services to make sure they are plugged in to their money-outlet. To compound the problem, when the power goes out someone else will likely notice and notify me. But if a bill is not payed, no one will ever notice until service is lost. Lost as in losing our domain name which would cause a lot more damage then the power failing on our server. [Solution] = [Doesn't work because]: Retrain the bookkeeper = Wishful thinking. Notify my manager = Already have (via email). Protects me, does not solve problem. Fire bookkeeper = What makes you so sure the next one will never forget? Bottom line: Humans are humans and sooner or later something critical will be royally messed up. We need to partner with a machine to help us out here. Anybody have the same problem? What software/solution do you use? I would like software that emails me when a bill is passed due just like i get an email when the power outlet fails. Anyone hear of anything like that? Thanks

  Read the article

• setting up Ubuntu 10.10 as paravirtualized guest in Xen on RHEL5 host - what kernel?

  - by kostmo

  I've discovered the tool ubuntu-vm-builder, which I've installed and then invoked on an Ubuntu workstation as: sudo vmbuilder xen ubuntu --suite maverick --flavour virtual --arch amd64 --mem=512 --rootsize 8192 This workstation is not the intended target host of the virtual machine, however; I would like to host the guest on a Red Hat Enterprise Linux 5 machine that is running Xen 3.0.3. The output of this command appears to be a folder named ubuntu-xen containing three files: tmpXXXXXX, a very large file which I assume is the root partition image tmpYYYYYY, a somewhat large file which I assume is the swap partition image xen.conf, a text file I have copied the xen.conf file to the RHEL server's /etc/xen directory under the new name newvm, adjusting the paths of tempXXXXXX and tempYYYYYYin the file after also copying them from my local workstation to the RHEL server. When I launch the Virtual Machine Manager virt-manager, I can see the newvm virtual machine listed underneath the Dom0 machine. When I try to start newvm, I get the error: Error starting domain: virDomainCreate() failed POST operation failed: (xend.err 'Error creating domain: Kernel image does not exist: None') Indeed, there exists an entry kernel = 'None' in the xen.conf file. How do I find out what the path of the kernel should be? Is this path supposed to be to a kernel stored on the local filesystem of the RHEL5 host, or is it supposed to be a path inside the guest image? I see that the vmbuilder command provides for a --xen-kernel option, along with a --xen-ramdisk option, but I'm not sure what to use for either. I think I should be able to get this to work, since Ubuntu is said to be supported as a Xen guest, even though the Xen 4.0.1 docs state support for only a limited set of distributions, Ubuntu excluded. Update 1 When running vmbuilder on my local workstation, I did observe an output line saying: Calling hook: install_kernel and later, output lines saying: update-initramfs: Generating /boot/initrd.img-2.6.35-23-virtual [...] run-parts: executing /etc/kernel/postinst.d/initramfs-tools 2.6.35-23-virtual /boot/vmlinuz-2.6.35-23-virtual So in the xen.conf file, I tried setting the lines: kernel = '/boot/vmlinuz-2.6.35-23-virtual' ramdisk = '/boot/initrd.img-2.6.35-23-virtual' When trying to start the VM, I got an error similar to last time: Error starting domain: virDomainCreate() failed POST operation failed: (xend.err 'Error creating domain: Kernel image does not exist: /boot/vmlinuz-2.6.35-23-virtual') This makes me think that the RHEL5 machine is looking for local files, rather than a file within the binary guest disk image. After running sudo updatedb on my workstation, neither of those files were found. If the vmbuilder tool had tried to install them, it must have failed. Update 2 I was able to extract the kernel and initrd images from the guest disk binary by mounting it: mkdir mnt_tmp sudo mount ubuntu-xen/tmpXXXXXX mnt_tmp/ -o loop cp mnt_tmp/boot/vmlinuz-2.6.35-23-virtual virtual_kernel_ubuntu cp mnt_tmp/boot/initrd.img-2.6.35-23-virtual virtual_initrd_ubuntu These two files I copied to the RHEL5 server, and edited the xen.conf file to point to them as kernel and ramdisk. With this done, I could "run" the newvm virtual machine from within virt-manager, but was met with the message Console Not Configured For Guest when I double clicked the entry to open the Virtual Machine Console. As suggested by a forum, I then added the line vfb = [ 'type=vnc' ] to the configuration file, recreated the virtual machine (a ~10 min process), and this time got the message: Connecting to console for guest This remained indefinitely; after selecting View - Serial Console, I found a kernel panic: [5442621.272173] Kernel panic - not syncing: Attempted to kill the idle task! [5442621.272179] Pid: 0, comm: swapper Tainted: G D 2.6.35-23-virtual #41-Ubuntu [5442621.272184] Call Trace: [5442621.272191] [<ffffffff815a1b81>] panic+0x90/0x111 [5442621.272199] [<ffffffff810652ee>] do_exit+0x3be/0x3f0 [5442621.272204] [<ffffffff815a5e20>] oops_end+0xb0/0xf0 [5442621.272211] [<ffffffff8100ddeb>] die+0x5b/0x90 [5442621.272216] [<ffffffff815a56c4>] do_trap+0xc4/0x170 [5442621.272221] [<ffffffff8100ba35>] do_invalid_op+0x95/0xb0 [5442621.272227] [<ffffffff8130851c>] ? intel_idle+0xac/0x180 [5442621.272232] [<ffffffff810072bf>] ? xen_restore_fl_direct_end+0x0/0x1 [5442621.272239] [<ffffffff815a48fe>] ? _raw_spin_unlock_irqrestore+0x1e/0x30 [5442621.272247] [<ffffffff8108dfb7>] ? tick_broadcast_oneshot_control+0xc7/0x120 [5442621.272253] [<ffffffff8100ad5b>] invalid_op+0x1b/0x20 [5442621.272259] [<ffffffff8130851c>] ? intel_idle+0xac/0x180 [5442621.272264] [<ffffffff813084e0>] ? intel_idle+0x70/0x180 [5442621.272269] [<ffffffff810072bf>] ? xen_restore_fl_direct_end+0x0/0x1 [5442621.272275] [<ffffffff8148a147>] cpuidle_idle_call+0xa7/0x140 [5442621.272281] [<ffffffff81008d93>] cpu_idle+0xb3/0x110 [5442621.272286] [<ffffffff815873aa>] rest_init+0x8a/0x90 [5442621.272291] [<ffffffff81b04c9d>] start_kernel+0x387/0x390 [5442621.272297] [<ffffffff81b04341>] x86_64_start_reservations+0x12c/0x130 [5442621.272303] [<ffffffff81b08002>] xen_start_kernel+0x55d/0x561 Update 3 I tried an i386 architecture instead of amd64, but got the same kernel panic. Also, it seems the Virtual Machine Manager pays attention to the format of the filename of the kernel; for the same kernel binary, I tried simply naming it vmlinuz-virtual, which threw out an error box about an invalid kernel. When I named it vmlinuz-2.6.35-23-virtual, it did not throw the error, but it did still result in the kernel panic shortly thereafter.

  Read the article

• Managing multiple independant domains with Google Apps

  - by Saif Bechan

  I am currently running a server where I have multiple domains with all of them running there own mail server. My plan is to outsource this whole email service and have Google, or competitor, do this for me. Let me start by telling you the setup I have now and want to migrate to Google. Initial setup I have a main domain where I run my server, and my nameserver. This is an important domain because this holds the connection with all my internal applications. For example log messages, cronjob messages, and virus-scan messages are sent to this domain. This email is also registered at my registrar and I use it to communicate with my ISP. Next I run a few independent websites that all need their independent email addresses. This can be on shared space, I don't mind. 1 Gig will be enough for everything I am going to do. Summary: superdomain.com (which only has a catchall for internal use and communication with my ISP) cars.com (independent) flowers.com (independent) foods.com (independent) I am going to be the admin for all of this. The independent domains don't need there own admin panel, they just need email addresses like info@ support@, etc. I do all the managing and they just send and receive emails using the accounts i give them. All of the websites have there different staff that use the accounts. Tried so far I have registered my superdomain, but I can only add aliases to the main domain. If I make all the other domains aliases the emails from [email protected] and [email protected] will have the same inbox. I want them to be separate. is the only way to achieve this by creating an account for each domain? And if so, is there no way of creating a superdomain account where I can edit all these accounts easily without having to log in 4 different places to get my work done. I have searched the Google help forums, and posted questions but without any results so far. Questions Can anyone please give me some advice on what to do. I currently use the free program Google has.

  Read the article

• Linux filesystem with inodes close on the disk

  - by pts

  I'd like to make the ls -laR /media/myfs on Linux as fast as possible. I'll have 1 million files on the filesystem, 2TB of total file size, and some directories containing as much as 10000 files. Which filesystem should I use and how should I configure it? As far as I understand, the reason why ls -laR is slow because it has to stat(2) each inode (i.e. 1 million stat(2)s), and since inodes are distributed randomly on the disk, each stat(2) needs one disk seek. Here are some solutions I had in mind, none of which I am satisfied with: Create the filesystem on an SSD, because the seek operations on SSDs are fast. This wouldn't work, because a 2TB SSD doesn't exist, or it's prohibitively expensive. Create a filesystem which spans on two block devices: an SSD and a disk; the disk contains file data, and the SSD contains all the metadata (including directory entries, inodes and POSIX extended attributes). Is there a filesystem which supports this? Would it survive a system crash (power outage)? Use find /media/myfs on ext2, ext3 or ext4, instead of ls -laR /media/myfs, because the former can the advantage of the d_type field (see in the getdents(2) man page), so it doesn't have to stat. Unfortunately, this doesn't meet my requirements, because I need all file sizes as well, which find /media/myfs doesn't print. Use a filesystem, such as VFAT, which stores inodes in the directory entries. I'd love this one, but VFAT is not reliable and flexible enough for me, and I don't know of any other filesystem which does that. Do you? Of course, storing inodes in the directory entries wouldn't work for files with a link count more than 1, but that's not a problem since I have only a few dozen such files in my use case. Adjust some settings in /proc or sysctl so that inodes are locked to system memory forever. This would not speed up the first ls -laR /media/myfs, but it would make all subsequent invocations amazingly fast. How can I do this? I don't like this idea, because it doesn't speed up the first invocation, which currently takes 30 minutes. Also I'd like to lock the POSIX extended attributes in memory as well. What do I have to do for that? Use a filesystem which has an online defragmentation tool, which can be instructed to relocate inodes to the the beginning of the block device. Once the relocation is done, I can run dd if=/dev/sdb of=/dev/null bs=1M count=256 to get the beginning of the block device fetched to the kernel in-memory cache without seeking, and then the stat(2) operations would be fast, because they read from the cache. Is there a way to lock those inodes and/or blocks into memory once they have been read? Which filesystem has such a defragmentation tool?

  Read the article

• What the best way to achieve RPO of zero and lowest possible RTO (less than 15 minutes) with SQL 2008 R2?

  - by Adrian Hope-Bailie

  We are running a payments (EFT transaction processing) application which is processing high volumes of transactions 24/7 and are currently investigating a better way of doing DB replication to our disaster recovery site. Our current and previous strategies have included using both DoubleTake and Redgate to replicate data to a warm stand-by. DoubleTake is the supported solution from the payments software vendor however their (DoubleTake's) support in South Africa is very poor. We had a few issues and simply couldn't ever resolve them so we had to give up on DoubleTake. We have been using Redgate to manually read the data from the primary site (via queries) and write to the DR site but this is: A bad solution Getting the software vendor hot and bothered whenever we have support issues as it has a tendency to interfere with the payment application which is very DB intensive. We recently upgraded the whole system to run on SQL 2008 R2 Enterprise which means we should probably be looking at using some of the built-in replication features. The server has 2 fairly large databases with a mixture of tables containing highly volatile transactional data and pretty static configuration data. Replication would be done over a WAN link to a separate physical site and needs to achieve the following objectives. RPO: Zero loss - This is transactional data with financial impact so we can't lose anything. RTO: Tending to zero - The business depends on our ability to process transactions every minute we are down we are losing money I have looked at a few of the other questions/answers but none meet our case exactly: SQL Server 2008 failover strategy - Log shipping or replication? How to achieve the following RTO & RPO with logshipping only using SQL Server? What is the best of two approaches to achieve DB Replication? My current thinking is that we should use mirroring but I am concerned that for RPO:0 we will need to do delayed commits and this could impact the performance of the primary DB which is not an option. Our current DR process is to: Stop incoming traffic to the primary site and allow all in-flight transaction to complete. Allow the replication to DR to complete. Change network routing to route to DR site. Start all applications and services on the secondary site (Ideally we can change this to a warmer stand-by whereby the applications are already running but not processing any transactions). In other words the DR database needs to, as quickly as possible, catch up with primary and be ready for processing as the new primary. We would then need to be able to reverse this when we are ready to switch back. Is there a better option than mirroring (should we be doing log-shipping too) and can anyone suggest other considerations that we should keep in mind?

  Read the article

• force unattended install php apt debian squeeze

  - by user1258619

  i am trying to do an unattended install via php for several packages but every time when the dependencies come up it aborts instead of forcing the answer to be yes. (i have broken apt a few times...) each time though i start off re-imaging my vps(testing server) so there isn't an issue of something still being hung or crashed.can someone tell me what i am doing wrong? keep in mind this is the 12th version of this script to get nowhere. fwrite(STDOUT, "Root Password:\n"); $root_pass = chop(fgets(STDIN)); $file_apt = '/etc/apt/apt.conf.d/70debconf'; // Open the file to get existing content $current_apt = file_get_contents($file_apt); // Append a new person to the file $current_apt .= "Dpkg::Options {\"--force-confold\";};\n"; // Write the contents back to the file file_put_contents($file_apt, $current_apt); $update = shell_exec('echo '.$root_pass.' | DEBIAN_FRONTEND=noninteractive sudo -S apt-get update'); echo $update; $update_upgrade = shell_exec('echo '.$root_pass.' | DEBIAN_FRONTEND=noninteractive sudo -s apt-get upgrade'); echo $update_upgrade; $install_unattended_mysql = shell_exec('echo '.$root_pass.' | DEBIAN_FRONTEND=noninteractive apt-get install --yes --force-yes mysql-server'); echo $install_unattended_mysql; $install_mysql_set_password = shell_exec('mysql -u root -e "UPDATE mysql.user SET password=PASSWORD("'.$root_pass.'") WHERE user="root"; FLUSH PRIVILEGES;'); echo $install_mysql_set_password; i have read a few places that i needed to edit the apt.conf file so i am doing so here and doing an update and an upgrade. also the upgrade does abort when it actually has to install something. The following packages will be upgraded: apache2 apache2-doc apache2-mpm-prefork apache2-utils apache2.2-bin apache2.2-common base-files bind9 bind9-host bind9utils debian-archive-keyring dpkg dselect libbind9-60 libc-bin libc6 libdns69 libisc62 libisccc60 libisccfg62 liblwres60 locales 22 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 18.4 MB of archives. After this operation, 8192 B of additional disk space will be used. Do you want to continue [Y/n]? Abort. I also should note that only a few pieces of software are going to be installed from the apt repo's as i will include some binaries to go along with it.

  Read the article

• Port forwarding not working properly

  - by sudo work

  I'm trying to host a small web server from my home network; however, I have not been able to successfully port forward ports to the local server. My current network topology looks like this: Cable Modem/Router - Secondary Wireless Router - Many computers (including server) The modem/router I'm using is a Cisco (Scientific Atlantic) DPC2100, provided by my ISP. The wireless router that I'm using as the central hub to my home network is a Linksys E3000. The computer being used as a server is running Ubuntu 10.04 Server Edition. The main issue is that I can't access the server remotely, using my WAN IP address. I have port forwarded my wireless router; however, I believe that I need to somehow set my modem to bridge mode. As far as I can tell though, this isn't possible. Here are the various IP address settings: DPC2100 WAN: 69.xxx.xxx.xxx Internal IP: 192.168.100.1 Internal Network: 192.168.7.0 E3000 IP Address: 192.168.7.2 Gateway: 192.168.7.1 Internal IP: 192.168.1.1 Internal Network: 192.168.1.0 Server IP Address: 192.168.1.123 Gateway: 192.168.1.1 Now I can do an nmap at various nodes, and here are the results (from the server): nmap localhost: 22,25,53,80,110,139,143,445,631,993,995,3306,5432,8080 open nmap 192.168.7.2: 22,25,80 (filtered),110,139,445 open (ports I have forwarded in the E3000)* nmap 69.xxx.xxx.xxx: 1720 open *For some reason, I can SSH into the server at 192.168.7.2, but not view the website. Here are also some other settings: /etc/hosts/ 127.0.0.1 localhost 127.0.1.1 servername ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters /etc/apache2/sites-available/default snippet <VirtualHost *:80> DocumentRoot /srv/www/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> ... </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> ... </Directory> ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> ... </Directory> </VirtualHost> Let me know if you need any other information; some stuff probably slipped my mind.

  Read the article

• When upgrading from Vista to Windows 7 on a DELL laptop, how do I know which drivers to reinstall an

  - by msorens

  According to Dell's upgrade page for Vista to Windows 7, after using the upgrade assistant the final step is to install drivers. They refer to this page for the order of driver installation, listing 9 items. From there I go to the Dell Drivers and Downloads page, enter my system tag, and get a list of the downloads available for my specific box. That page, by the way, has a link to driver install instructions that lists 10 rather than 9 items. Going to Drivers Help in the side panel and clicking on "In what order should drivers be installed?" shows yet a third list, this one containing 13 items. Not surprisingly, the order of these 3 lists of drivers are not quite the same for the common items! Furthermore, of the 26 files Dell's site recommends for my machine, there are several not shown on any of the 3 lists! I can make determinations for some of these: 6 of them are "applications" so I know which of those I want and that they could probably be safely installed after all drivers. BIOS: I would think this should be unaffected by an OS upgrade so could be skipped. Two tools in the diagnostics category: could probably be done after all drivers. That leaves just a CD/DVD driver and a webcam driver unaccounted for. So my two related questions are these: How critical is the driver installation order and which one do I follow? (Keep in mind this is for an upgrade, not a fresh install.) Where in the order do I insert the CD/DVD and the webcam drivers (if needed) ? Dell's driver download page provides (in theory) the list of all downloads relevant to my specific machine, via the service tag. But do I actually need to reinstall all of them? some? none? How does one determine this? They do label each with Recommended or Optional, so do I need to reinstall all the recommended ones? (Part of the reason for my perplexed frown is that I wonder why I would need to reinstall a CD/DVD driver since I would already be using the drive to install the OS!)

  Read the article

• Anti-virus protection question?

  - by DaBaer

  About 4 years ago, I found Kaspersky and have been using the most current version since. Most people try and argue the use of AVG or Avast to me, and there are some very solid reasons I do not go that route. Over the years, I have found Kasp to become bulkier and bulkier, and have had issues setting it up for friends/family/clients. I am just curios on possible recommendations from other users, with my criteria in mind: What I like about Kasp in the past: The license sold in stores in a 3 pack, is considered a commercial license, and emails from Kasp in response to my questions, make it clear that I can do with the 3 licenses that I want, providing I do not use more than 3 installs per Key. So, allowed me to buy 3, 5, and 7 packs, and resell to users at a cheaper cost than what they would pay if they bought their own license. The ability to easily obtain a currently updated .exe for installation on multiple peoples machines. Power of the scan. Kasp has been a good solution for me (even when using a trial license) on cleaning up machines that were badly infected (in which AVG and AVAST were unable to.) Speed of install/update. After a cleanup of malwarebytes, spybot, mcafee stinger, ccleaner, and combofix, I used to be able to get Kasp Int Security installed and updated in around 5 minutes. The issues that I have with the free AV, is strength of protection. In my opinion for someone who is a 'power use' these are good alternatives, because such a user should be trained or knowledgeable enough to be careful and not get themselves in trouble. Most of the users I assist, are too PC ignorant to know any better, and go hogwild on the web. It has been my experience that the number of people coming back to me with spyware/malware/virus issues since I have converted from AVG to Kasp has been cut down to around 20% of what it used to be 4 or 5 years ago. In a perfect world, I could install and use Kasp Internet Security 2008, and be very happy. But this is not the case anymore. So after this long description of what I used, and have used, does anyone have any good recommendations on AV that isn't going to cost me too much per install?

  Read the article

• e2fsck extremly slow, although enough memory exists

  - by kaefert

  I've got this external USB-Disk: kaefert@blechmobil:~$ lsusb -s 2:3 Bus 002 Device 003: ID 0bc2:3320 Seagate RSS LLC As can be seen in this dmesg output, there are some problems that prevents that disk from beeing mounted: kaefert@blechmobil:~$ dmesg | grep sdb [ 114.474342] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.475089] sd 5:0:0:0: [sdb] Write Protect is off [ 114.475092] sd 5:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 114.475959] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 114.477093] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.501649] sdb: sdb1 [ 114.502717] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.504354] sd 5:0:0:0: [sdb] Attached SCSI disk [ 116.804408] EXT4-fs (sdb1): ext4_check_descriptors: Checksum for group 3976 failed (47397!=61519) [ 116.804413] EXT4-fs (sdb1): group descriptors corrupted! So I went and fired up my favorite partition manager - gparted, and told it to verify and repair the partition sdb1. This made gparted call e2fsck (version 1.42.4 (12-Jun-2012)) e2fsck -f -y -v /dev/sdb1 Although gparted called e2fsck with the "-v" option, sadly it doesn't show me the output of my e2fsck process (bugreport https://bugzilla.gnome.org/show_bug.cgi?id=467925 ) I started this whole thing on Sunday (2012-11-04_2200) evening, so about 48 hours ago, this is what htop says about it now (2012-11-06-1900): PID USER PRI NI VIRT RES SHR S CPU% MEM% TIME+ Command 3704 root 39 19 1560M 1166M 768 R 98.0 19.5 42h56:43 e2fsck -f -y -v /dev/sdb1 Now I found a few posts on the internet that discuss e2fsck running slow, for example: http://gparted-forum.surf4.info/viewtopic.php?id=13613 where they write that its a good idea to see if the disk is just that slow because maybe its damaged, and I think these outputs tell me that this is not the case in my case: kaefert@blechmobil:~$ sudo hdparm -tT /dev/sdb /dev/sdb: Timing cached reads: 3562 MB in 2.00 seconds = 1783.29 MB/sec Timing buffered disk reads: 82 MB in 3.01 seconds = 27.26 MB/sec kaefert@blechmobil:~$ sudo hdparm /dev/sdb /dev/sdb: multcount = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 364801/255/63, sectors = 5860533160, start = 0 However, although I can read quickly from that disk, this disk speed doesn't seem to be used by e2fsck, considering tools like gkrellm or iotop or this: kaefert@blechmobil:~$ iostat -x Linux 3.2.0-2-amd64 (blechmobil) 2012-11-06 _x86_64_ (2 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 14,24 47,81 14,63 0,95 0,00 22,37 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util sda 0,59 8,29 2,42 5,14 43,17 160,17 53,75 0,30 39,80 8,72 54,42 3,95 2,99 sdb 137,54 5,48 9,23 0,20 587,07 22,73 129,35 0,07 7,70 7,51 16,18 2,17 2,04 Now I researched a little bit on how to find out what e2fsck is doing with all that processor time, and I found the tool strace, which gives me this: kaefert@blechmobil:~$ sudo strace -p3704 lseek(4, 41026998272, SEEK_SET) = 41026998272 write(4, "\212\354K[_\361\3nl\212\245\352\255jR\303\354\312Yv\334p\253r\217\265\3567\325\257\3766"..., 4096) = 4096 lseek(4, 48404766720, SEEK_SET) = 48404766720 read(4, "\7t\260\366\346\337\304\210\33\267j\35\377'\31f\372\252\ffU\317.y\211\360\36\240c\30`\34"..., 4096) = 4096 lseek(4, 41027002368, SEEK_SET) = 41027002368 write(4, "\232]7Ws\321\352\t\1@[+5\263\334\276{\343zZx\352\21\316`1\271[\202\350R`"..., 4096) = 4096 lseek(4, 48404770816, SEEK_SET) = 48404770816 read(4, "\17\362r\230\327\25\346//\210H\v\311\3237\323K\304\306\361a\223\311\324\272?\213\tq \370\24"..., 4096) = 4096 lseek(4, 41027006464, SEEK_SET) = 41027006464 write(4, "\367yy>x\216?=\324Z\305\351\376&\25\244\210\271\22\306}\276\237\370(\214\205G\262\360\257#"..., 4096) = 4096 lseek(4, 48404774912, SEEK_SET) = 48404774912 read(4, "\365\25\0\21|T\0\21}3t_\272\373\222k\r\177\303\1\201\261\221$\261B\232\3142\21U\316"..., 4096) = 4096 ^CProcess 3704 detached around 16 of these lines every second, so 4 read and 4 write operations every second, which I don't consider to be a lot.. And finally, my question: Will this process ever finish? If those numbers from fseek (48404774912) represent bytes, that would be something like 45 gigabytes, with this beeing a 3 terrabyte disk, which would give me 134 days to go, if the speed stays constant, and he scans the disk like this completly and only once. Do you have some advice for me? I have most of the data on that disk elsewhere, but I've put a lot of hours into sorting and merging it to this disk, so I would prefer to getting this disk up and running again, without formatting it anew. I don't think that the hardware is damaged since the disk is only a few months and since I can't see any I/O errors in the dmesg output. UPDATE: I just looked at the strace output again (2012-11-06_2300), now it looks like this: lseek(4, 1419860611072, SEEK_SET) = 1419860611072 read(4, "3#\f\2447\335\0\22A\355\374\276j\204'\207|\217V|\23\245[\7VP\251\242\276\207\317:"..., 4096) = 4096 lseek(4, 43018145792, SEEK_SET) = 43018145792 write(4, "]\206\231\342Y\204-2I\362\242\344\6R\205\361\324\177\265\317C\334V\324\260\334\275t=\10F."..., 4096) = 4096 lseek(4, 1419860615168, SEEK_SET) = 1419860615168 read(4, "\262\305\314Y\367\37x\326\245\226\226\320N\333$s\34\204\311\222\7\315\236\336\300TK\337\264\236\211n"..., 4096) = 4096 lseek(4, 43018149888, SEEK_SET) = 43018149888 write(4, "\271\224m\311\224\25!I\376\16;\377\0\223H\25Yd\201Y\342\r\203\271\24eG<\202{\373V"..., 4096) = 4096 lseek(4, 1419860619264, SEEK_SET) = 1419860619264 read(4, ";d\360\177\n\346\253\210\222|\250\352T\335M\33\260\320\261\7g\222P\344H?t\240\20\2548\310"..., 4096) = 4096 lseek(4, 43018153984, SEEK_SET) = 43018153984 write(4, "\360\252j\317\310\251G\227\335{\214`\341\267\31Y\202\360\v\374\307oq\3063\217Z\223\313\36D\211"..., 4096) = 4096 So this number of the lseeks before the reads, like 1419860619264 are already a lot bigger, standing for 1.29 terabytes if the numbers are bytes, so it doesn't seem to be a linear progress on a big scale, maybe there are only some areas that need work, that have big gaps in between them. (times are in CET)

  Read the article

< Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >